MAXIMO The panel formwork with the MX Tie which is installed from one side only

Transcription

1 MAXIMO The panel formwork with the MX Tie which is installed from one side only The PERI MX Tie

2 Edition 02/2010 PERI GmbH Formwork Scaffolding Engineering P.O. Box Weissenhorn Germany Tel +49 (0) Fax +49 (0) Important Notes: Without exception, all current safety regulations must be observed in those countries where our products are used. The illustrations in this brochure are photographs of particular situations on a construction site. Safety or formwork anchor details are therefore not to be taken as a definitive guide to the way the equipment is to be used. Safety instructions and load specifications are to be strictly observed at all times. Separate structural calculations are required for any deviations from the standard design data. The information contained herein is subject to technical changes in the interests of progress. Errors and typographical mistakes reserved.

3 Content MAXIMO 3 The panel formwork with the MX Tie which is installed from one side only Faster 4 with the MX Tie which is installed from one side only Time saving 6 through systematised tie points 8 through the reduced number of tie points 9 through low site personnel requirements MAXIMO 11 Less individual operations = faster forming Improved concrete finish 12 through a neat joint and tie arrangement Project examples 14 The optimal system for all requirements Reliable 16 through systematised sealing technology Standard application with Inside Corner 50/20 20 Panel connections, T-junctions, wall connections, corners, wall offsets Standard applications 22 Stopend formwork, fillers, oblique angles Supplementary system components 24 Inside Corner 60/60 25 Push-Pull Spreader 26 Components 1

4

5 MAXIMO The panel formwork with the MX Tie which is installed from one side only Since its launch in 1986, PERI TRIO has developed into the world s most successful panel formwork system. Arguments such as few different panel sizes or only one single connecting part, the BFD alignment coupler, have set benchmarks in the industry. With the development of MAXIMO, PERI has justified its role as technological market leader. This independent formwork system - fully compatible to TRIO - fulfils the highest requirements regarding costeffectiveness and achievable quality of workmanship. Photo left: perfectly designed concrete surfaces using MAXIMO at the PERI branch office in Viersen. PERI MAXIMO panel formwork Faster through one-sided anchoring with the MX Tie technology without spacer tubes Time saving through the systematised and reduced number of tie points Improved concrete finish through a neat joint and tie arrangement Flexible panel formwork system for all requirements on small building sites as well as for large construction projects. The MX tie is installed from one side only which makes the MAXIMO particularly cost-effective. Cellar of a single-family house in Buchenberg/ Vorderburg, Germany. The neat joint and tie arrangement allows construction of concrete surfaces of the highest quality. Multi-storey car park in Mainz, Germany. PERI MAXIMO 3

6 Faster with the MX Tie which is installed from one side only MX Tie Item no for wall thicknesses 20/22/24/25/30 The conical-shaped MX Tie rod is also set in the concrete when filling the formwork. Due to the special form, spacer tubes and cones are not required. This saves materials and the tie can be installed and removed considerably quicker MX Tie Item no for wall thicknesses 15/17.5/20/22/24/25 MX Tie Item no for wall thicknesses 30/35/36/40 MX Tie System assembly sequence Preparation Tie installation A. Placing Formwork B. Ties Position MX Wingnut, attach Eye Bolt and tighten with the MX Tie Rod Spanner. Peg out the required wall thickness with cotter pins and turn the nut against the cotter pin. 1. Push the tie through through the closing formwork into the wingnut of the placing formwork and screw in. 2. Screw in MX Tie with the MX Tie Rod Spanner-2 until the Eye Bolt can be attached. 4 PERI MAXIMO

7 With the PERI MAXIMO, the conventional DW 15 and DW 20 systems can be used as well as the MX tie technology. The opening in the frame allows deviations of the tie rod angle of ± 4. The tie hole is protected against any impact through a metal ring. The Sealing Sleeve seals the tie point and prevents any concrete bleeding. MX Wingnut Item no MX Tie Rod Spanner-2 Item no Dismantling ties 1. First loosen and then completely unscrew the Eye Bolt. 2. Remove ties by means of the MX Tie Rod Spanner Tighten MX tie with the MX Tie Rod Spanner-2 as far as it can go. 4. Tighten Eye Bolt. PERI MAXIMO 5

8 Time saving through systematised tie points With MAXIMO, the tie points are systematized, i. e. all panel sizes are centrically arranged and each position is engaged. MAXIMO tie point. MAXIMO does not require any edge ties, all tie points are always engaged. With conventional panel formwork, all unused edge tie points must be closed. Additional work is frequently necessary due to unclosed tie holes: Freeing the tie points in the panel which have been plugged with concrete. Concrete cosmetic work on the concrete surfaces affected by bleeding. 6 PERI MAXIMO

9 Width Height Panel grid arrangement 30 cm MAXIMO panels are available in 6 heights from 30 cm up to 3.30 m as well as 5 widths from 30 cm to 2.40 m in 30 cm increments. In addition, a 45 cm wide panel is available which greatly reduces the use of filler plates. Panel connections with the BFD alignment coupler The BFD alignment coupler ensures neat panel joints resulting in perfect concrete finishes. With only one component, every panel connection is flush, aligned and tight. PERI MAXIMO 7

10 Time saving through the reduced number of tie points Conventional formwork PERI MAXIMO tie point savings Comparison: PERI MAXIMO vs. conventional panel formwork Apart from the time advantage due to the MX tie being operated from one side only, the reduced number of tie points has a positive effect on the performance factor. MAXIMO requires up to 40% fewer ties results in a clear panel arrangement ensures a neat tie and joint pattern Due to the centricallypositioned arrangement, up to 40% fewer ties are required. In spite of the low number of required ties, concreting can still be carried out quickly with MAXIMO. High permissible concrete pressure Permissible fresh concrete pressure for 2.70 m panels according to DIN kn/m 2 uniform load DIN 18202, Table 3, Line kn/m² triangular load DIN 18202, Table 3, Line 7. Maximo fulfils the high demands regarding the flatness. The high rigidity of the panels ensures only minimum deflection and distortion as well as being a guarantee for a high level of concrete surface evenness. 8 PERI MAXIMO

11 Time saving through low site personnel requirements For the construction of concrete walls with panel formwork, the two formwork elements facing each other must be anchored. MX Tie DW 15 Tie MAXIMO With the innovative tie system of the MAXIMO panel formwork elements, tie operations take place after a one-off basic assembly of the wingnut on the placing formwork always from one side only. Thus, one less worker is required the performance factor is reduced by approx. 40%. Conventional formwork For conventional systems, one worker is required on each side of the formwork for this working step. More information about the comparison is available at: PERI MAXIMO 9

12 Working scaffold is not required resulting in more savings Due to the fact that ties are installed from one side only, additional safety measures such as working scaffold for the placing formwork are not necessary which saves both time and money. This is of great importance particularly for high formwork. 10 PERI MAXIMO

13 MAXIMO Less individual operations = faster forming Comparison Conventional panel formwork vs. MAXIMO Conventional Shuttering - reinforcement work - concreting formwork MAXIMO 1 Lay out/indicate on the bottom slab Assemble placing formwork Oil and mount MX Wingnut + 4 Oil placing formwork Erect placing formwork/ fix push-pull props Mount guardrails (intermediate position for tie operations for heights over 3.00 m) ++ 7 Position reinforcement scaffold Lay out of box-outs/indicate Nail on box-out units Close unused tie holes + 11 Turn wingnut pivot plate on the tie + 12 Insert tie + 13 Cutting the spacer tubes to size + 14 Attach cones to spacer tube on both sides + 15 Push spacer tube on tie + 16 Reinforcement work Remove reinforcement scaffold Adjust MX Tie to wall thickness (only once is necessary according to specified wall thickness) + 19 Assemble closing formwork Oil closing formwork Attach guardrails Erect closing formwork Oil MX Tie + 24 Screw in MX Tie (1 worker) + 25 Attach eye bolt + 26 Screw wingnut counterplate on tie (2 workers) If necessary, re-plugging of incorrectly closed tie points (2 workers) Setting of stopends Concreting + + Striking 30 Release wingnut counterplate (2 workers) Remove tie (2 workers) Release eye bolt (1 worker) + 33 Remove MX Tie (1 worker) + 34 Closing formwork is retracted and removed Cleaning of closing formwork Placing formwork is retracted and re-positioned (ideally) Clean placing formwork Removing the compression cones + 39 If necessary, cosmetic work to repair impressions in the concrete due to unclosed tie holes If, necessary, freeing of concrete residue from tie holes in the formwork + Miscellaneous Up to 25% more ties in conventional formwork, especially with high formwork ++ In tightly-spaced shaft internal formwork, a second worker is required for conventional ties ++ PERI MAXIMO 11

14 Improved concrete finish through a neat joint and tie arrangement Designing concrete surfaces Systematically, cost-effective, simple A frequent request of building owners and architects is the realisation of special wall surfaces without any large additional work and expense using an efficient panel formwork system. PERI MAXIMO is the panel formwork with centrically arranged tie points for each panel. This results in a regular joint arrangement - horizontally as well as vertically. Concrete surface design with the MX grid arrangement With the possibility to select from a range of panel combinations, this provides more creative freedom and thus more design options - cost-effectively realised with PERI MAXIMO. Example: MX tie arrangement Stack More information available at: 12 PERI MAXIMO

15 The defined arrangement of individual MAXIMO panels in so-called MX grid, allows the creation of attractively-designed visible concrete finishes: neat concrete surfaces no impressions from unused tie points no concrete bleeding from unclosed tie points Perfectly designed concrete surfaces with PERI MAXIMO. PERI MAXIMO 13

16 Project examples The optimal system for all requirements Regular joint and tie arrangement on visibly remaining wall surfaces. Outlet Centre Business Complex, Metzingen, Germany Short construction period with a small number of site personnel. Cellar for a semi-detached house, Rosenheim, Germany 14 PERI MAXIMO

17 In addition to the requirement of being able to be used flexibly as well as efficiently on the construction site for all those components to be constructed, MAXIMO also fulfils the requirement to create the remaining visible concrete surfaces in high quality through the skilful selection and arrangement of the panels. MAXIMO for high, inclined walls in combination with SKS climbing brackets. Congress Centre am Schlossberg, Heidenheim, Germany Extension of the Environmental Research Station Schneefernerhaus, Zugspitze, Germany MAXIMO in climbing operations on Folding Platforms FB 180. Siemens Logistics Centre, Frankfurt, Germany High, visibly remaining wall surfaces. Rehabilitation Centre, Stuttgart-Fellbach, Germany A triple extension, moved as a complete unit and requiring no working scaffold on the opposite side. Rehearsal stage at the Staatstheater, Stuttgart, Germany PERI MAXIMO 15

18 Reliable through systematised sealing technology Anchoring With the MX Tie MX Tie Depending on the wall thickness (see page 4). Sealing system Plug MX Ø Item no Large lamellas. For all hole diameters mm. Stopper MX 50 OF Item no Deeply inserted. For all hole diametets mm*. Requirements Sealing only for visual effect. Sealing against non-pressing water. Walls with a sound protection function*. Walls with Fire Resistance Class F90*. *Test reports available. Closing tie points Assembly Installation takes place using an Allen key or even faster with the help of a battery-powered screwdriver in seconds - regardless of environmental influences, such as temperature, and concrete technology. Allen Key 4 mm 16 PERI MAXIMO

19 Aufbau- und Verwendungsanleitung für die Regelausführung Ausgabe 12/2009 Stopper MX 50 MF Item no Install flush with the surface. Stopper MX 84 MF Item no Install flush with the surface. Sealing against non-pressing water. Walls with a sound protection function*. Walls with Fire Resistance Class F90*. *Test reports available. Sealing against pressing water according to DIN EN 206-1/ for components with high water penetration resistance*. Walls with sound protection function*. Walls with Fire Resistance Class F90*. *Test reports available. Installation takes place using an Allen key or even faster with the help of a battery-powered screwdriver in seconds - regardless of environmental influences, such as temperature, and concrete technology. Stud Spanner MAXIMO Item no For holding the stoppers. MAXIMO Rahmenschalung The PERI assembly instructions for MAXIMO should be taken into account! PERI MAXIMO 17

20 Reliable through systematised sealing technology Anchoring With MX Ties and Sealing Cones MX 55 Magnet Cone MX 55 Item no Magnets are fitted in the cone which means it is reliably fixed to the metal ring of the sealing integrated in the panel. Sealing system DK Concrete Cone DW 15-58/30 Item no DK Concrete Cone Architectural/01 DW 15-58/52 Item no DK Concrete Cone UNI 58/52 Item no Requirements Used for attractively designed visible concrete surfaces. Deeply inserted. Used for attractively designed visible concrete surfaces. With shadow joints. Against pressing water according to DIN EN 206-1/ for components with high water penetration resistance*, e.g. for sewage plants or drinking water containers whereby the concrete surface and cones must be flush. Walls with sound protection function* Walls with Fire Resistance Class F90*, e.g. stairways. *Test reports available. Closing tie points Assembly Dismantling of the sealing cone takes place with help of the MX Magnet Cone Spanner. For installing the concrete cones, see PERI Tie Technology brochure. Magnet Cone Spanner MX Item no PERI MAXIMO

21 With Tie Rod DW 15 and Cone MX DR 22 With Tie Rod DW 20 and DK Sealing Cone DW 20/55 Cone MX DR 22 Item no For use with Spacer Tube, Rough DR 22 or Concrete Spacer Tube FZR. Covers the sealing on the panel. DK Sealing Cone DW 20/55 Item no For use with Spacer Tube DR 28 and DR Concrete Cone UNI 58/52. Plug DR 22 Item no Plug FRZ 22 Item no Correspondingly, the DK Sealing Cones can also be used for DW 15 DK Concrete Cone UNI 58/52 Item no or only as a visual function. For sealing against pressing water according to DIN EN 206-1/ for components with high water penetration resistance*. Walls with Fire Resistance Class F90*, e.g. stairways. *Test reports available. PERI MAXIMO 19

22 Standard application with Inside Corner 50/20 Panel connections, T-junctions, wall connections Panel connections Wall connections With Alignment Coupler BFD Item no T-Junctions Wall thickness cm Internal formwork Inside Corner MXI 50/20 3 x Alignment Coupler BFD 60 MXI 50/ MXI 50/ External formwork Panel MX 60 2 x Alignment Coupler BFD Adapting to the wall thickness with Wall Thickness Compensator MX or timber. 3 x Alignment Coupler BFD MXI 50/20 MXI 50/20 MXI 50/ MXI 50/20 MXI 50/20 MXI 50/ PERI MAXIMO

23 Corners, Wall Offsets Corners with MXI 50/20 Wall thickness cm Internal Formwork Inside Corner MXI 50/20 3 x Alignment Coupler BFD External Formwork Outside Corner MXA 45 Panel MX 30 4 x Alignment Coupler BFD MXA / 45 / 30 MXA / 45 / 30 MXA / 45 / / 45 / / 45 / / 45 / 30 MXI 50/20 MXI 50/20 MXI 50/ /25 30 No tie is required on the short side of the Inside Corner MXI 50/20. Wall Offset 30 MXA MXI 50/20 MXI 50/20 MXI 50/20 MXI 50/ MXA cm Inside Corner MXI 50/20 Panel MX 45 Compensation Waler MAR 170 Compensation Waler MAR 85 filler timber supplied by contractor cm Inside Corner MXI 50/20 Outside Corner MXA 45 Panel MX 30 Compensation Waler MAR 170 with 1 Hook Tie DW 15 and Wingnut Pivot Plate Compensation Waler MAR 85 with 1 Hook Tie DW 15 and Wingnut Pivot Plate filler timber supplied by contractor PERI MAXIMO 21

24 Standard applications Stopend Formwork Stopend Formwork With a conventional solution 3 x Compensation Waler MAR 85-2 at 2.70 m height. With TRIO Stopend Panel MT/MTF For continuous reinforcement, with or without water bars. Time savings min. 40%. No damage to the formlining. Centre Section MT, without water bar Centre Section MTF, with water bar 22 PERI MAXIMO

25 Fillers, Oblique Angles Fillers Up to 10 cm With Wall Thickness Compensator MX or timbers and Alignment Coupler BFD. 10 cm to 36 cm With Filler Support TPP and formlining. TPP 270, Item no TPP. Item no Oblique Angles 75 External formwork Articulated Corner MX outside Panel MXM 60 Panel MX 45 and MX 30 at 75 Internal formwork Articulated Corner MX inside Panel MX 45 Panel MX 30 at 75 Outside: 3 x BFD x SRU Inside: 2 x BFD Outside: 3 x BFD x MAR Inside: 2 x BFD 1 6 = number of struts PERI MAXIMO 23

26 Supplementary System Components: Inside Corner 60/60 For perfectly-finished concrete surfaces and when using the Sealing Cone MX 55 Corners Wall thickness cm Internal formwork Inside Corner MXI 60/60 3 x Alignment Coupler BFD External formwork Outside Corner MXA 35 or 45 2 x Panel MX 45 4 x Alignment Coupler BFD MXA MXI 60 T-Junctions Wall thickness cm Internal formwork Inside Corner MXI 60/60 3 x Alignment Coupler BFD 45 External formwork 2 x Panel MX 45 1 x Panel MX 60 3 x MAR x Alignment Coupler BFD MXi PERI MAXIMO

27 Push-Pull Spreader The middle tie point brings decisive advantages when forming foundations, parapets and beams. Through the use of the push-pull spreader in connection with the middle tie of the MAXIMO panel, a bottom row of ties is not necessary. Push-Pull Spreader MX Item no Foundations/Upturn Beams Only a minimum of working space is required. Water stop metal strips are no hindrance. Parapet or other similar structural components Beam Thick reinforcement is no problem. PERI MAXIMO 25

28 MAXIMO Panel Formwork Item no. Weight kg ,000 Panel MX 330 x m². Panel with plywood 18 mm ,000 Panel MX 330 x m². Panel with plywood 18 mm ,000 Panel MX 330 x m². Panel with plywood 18 mm

29 MAXIMO Panel Formwork Item no. Weight kg ,000 Panel MX 330 x m². Panel with plywood 18 mm ,000 Panel MX 330 x m². Panel with plywood 18 mm ,800 Panel MX 330 x m². Panel with plywood 18 mm

30 MAXIMO Panel Formwork Item no. Weight kg , Panel MX 330 x m². Panel with plywood 18 mm ,000 Multi-Purpose Panel MXM 330 x m². Panel with plywood 18 mm. For oblique angles, wall connections etc. Complete with 33 x Plug MXM Ø x Sealing MXM Ø x 40 = ,000 Inside Corner MXI 330 x m². Panel with plywood 18 mm. For 90 inside corners

31 MAXIMO Panel Formwork Item no. Weight kg ,000 Inside Corner MXI 330 x 50/20 2,310 m 2. Panel with plywood 18 mm. For 90 inside corners. Complete with 12 x Plug MXM Ø x Sealing MXM Ø ,000 Outside Corner MXA 330 x 45 2,970 m 2. Panel with plywood 18 mm. For 90 outside corners ,000 Outside Corner MXA 330 x 35 2,310 m 2. Panel with plywood 18 mm. For 90 outside corners

32 MAXIMO Panel Formwork Item no. Weight kg , Articulated Corner MXGI m². Made of aluminium. For oblique angles from 75 for the inside ,100 Articulated Corner MXGA m². Made of aluminium. For oblique angles from 75 for the outside ,800 18,900 20,200 12,100 Wall Thickness Compensators WDA MX 330 Wall Thickness Comp. WDA MX 330 x 4 Wall Thickness Comp. WDA MX 330 x 5 Wall Thickness Comp. WDA MX 330 x 6 Wall Thickness Comp. WDA MX 330 x 10, Alu For adaptating to different wall thicknesses. B B

33 MAXIMO Panel Formwork Item no. Weight kg ,790 Filler Profile TPP 330, Alu For infillings with 21 mm plywood ,000 Panel MX 270 x m². Panel with plywood 18 mm ,000 Panel MX 270 x m². Panel with plywood 18 mm

34 MAXIMO Panel Formwork Item no. Weight kg ,000 Panel MX 270 x m². Panel with plywood 18 mm ,000 Panel MX 270 x m². Panel with plywood 18 mm , Panel MX 270 x m². Panel with plywood 18 mm

35 MAXIMO Panel Formwork Item no. Weight kg ,800 Panel MX 270 x m². Panel with plywood 18 mm ,000 Multi-Purpose Panel MXM 270 x m². Panel with plywood 18 mm. For oblique angles, wall connections etc. Complete with 22 x Plug MXM Ø x Sealing MXM Ø x 40 = ,000 Inside Corner MXI 270 x m². Panel with plywood 18 mm. For 90 inside corners

36 MAXIMO Panel Formwork Item no. Weight kg ,000 Inside Corner MXI 270 x 50/ m². Panel with plywood 18 mm. For 90 inside corners. Complete with 8 x Plug MXM Ø x Sealing MXM Ø ,000 Outside Corner MXA 270 x 90 4,860 m². Panel with plywood 18 mm. For 90 outside corners. Complete with 24 x Plug MXM Ø x Sealing MXM Ø ,000 Outside Corner MXA 270 x m². Panel with plywood 18 mm. For 90 outside corners

37 MAXIMO Panel Formwork Item no. Weight kg ,000 Outside Corner MXA 270 x m². Panel with plywood 18 mm. For 90 outside corners ,400 Articulated Corner MXGI m². Made of aluminium. For oblique angles from 75 for the inside ,800 Articulated Corner MXGA m². Made of aluminium. For oblique angles from 75 for the outside

38 MAXIMO Panel Formwork Item no. Weight kg ,700 15,700 16,800 10,000 Wall Thickness Compensators WDA MX 270 Wall Thickness Comp. WDA MX 270 x 4 Wall Thickness Comp. WDA MX 270 x 5 Wall Thickness Comp. WDA MX 270 x 6 Wall Thickness Comp. WDA MX 270 x 10, Alu For adaptating to different wall thicknesses. B B ,050 Filler Profile TPP 270, Alu For infillings with 21 mm plywood ,000 Panel MX x m². Panel with plywood 18 mm

39 MAXIMO Panel Formwork Item no. Weight kg ,700 Panel MX x m². Panel with plywood 18 mm ,700 Panel MX x m². Panel with plywood 18 mm ,200 Panel MX x m². Panel with plywood 18 mm ,100 Panel MX x m². Panel with plywood 18 mm

40 MAXIMO Panel Formwork Item no. Weight kg ,400 Panel MX x m². Panel with plywood 18 mm ,400 Multi-Purpose Panel MXM x m². Panel with plywood 18 mm. For oblique angles, wall connections etc. Complete with 11 x Plug MXM Ø x Sealing MXM Ø x 40 = ,500 Inside Corner MXI x m². Panel with plywood 18 mm. For 90 inside corners ,500 Inside Corner MXI x 50/ m². Panel with plywood 18 mm. For 90 inside corners. Complete with 4 x Plug MXM Ø x Sealing MXM Ø

41 MAXIMO Panel Formwork Item no. Weight kg ,000 Outside Corner MXA x m². Panel with plywood 18 mm. For 90 outside corners. Complete with 12 x Plug MXM Ø x Sealing MXM Ø ,300 Outside Corner MXA x m². Panel with plywood 18 mm. For 90 outside corners ,200 Outside Corner MXA x m². Panel with plywood 18 mm. For 90 outside corners ,200 Articulated Corner MXGI m². Made of aluminium. For oblique angles from 75 for the inside

42 MAXIMO Panel Formwork Item no. Weight kg ,000 Articulated Corner MXGA m². Made of aluminium. For oblique angles from 75 for the outside ,430 6,990 7,480 4,510 Wall Thickness Compensators WDA MX Wall Thickness Comp. WDA MX x 4 Wall Thickness Comp. WDA MX x 5 Wall Thickness Comp. WDA MX x 6 Wall Thickness Comp. WDA MX x 10, Alu For adaptating to different wall thicknesses. B B , Filler Profile TPP, Alu For infillings with 21 mm plywood ,000 Panel MX 90 x m². Panel with plywood 18 mm

43 MAXIMO Panel Formwork Item no. Weight kg ,900 Panel MX 90 x m². Panel with plywood 18 mm , Panel MX 90 x m². Panel with plywood 18 mm ,200 Panel MX 90 x m². Panel with plywood 18 mm ,000 Panel MX 90 x m². Panel with plywood 18 mm

44 MAXIMO Panel Formwork Item no. Weight kg ,100 Inside Corner MXI 90 x m². Panel with plywood 18 mm. For 90 inside corners , Inside Corner MXI 90 x 50/ m². Panel with plywood 18 mm. For 90 inside corners. Complete with 4 x Plug MXM Ø x Sealing MXM Ø ,000 Outside Corner MXA 90 x m². Panel with plywood 18 mm. For 90 outside corners. Complete with 12 x Plug MXM Ø x Sealing MXM Ø ,100 Panel MX 60 x m². Panel with plywood 18 mm ,400 Panel MX 60 x m². Panel with plywood 18 mm

45 MAXIMO Panel Formwork Item no. Weight kg ,900 Panel MX 60 x m². Panel with plywood 18 mm ,200 Panel MX 60 x m². Panel with plywood 18 mm ,400 Inside Corner MXI 60 x m². Panel with plywood 18 mm. For 90 inside corners ,400 Inside Corner MXI 60 x 50/ m². Panel with plywood 18 mm. For 90 inside corners. Complete with 4 x Plug MXM Ø x Sealing MXM Ø ,700 Outside Corner MXA 60 x m². Panel with plywood 18 mm. For 90 outside corners. Complete with 12 x Plug MXM Ø x Sealing MXM Ø

46 MAXIMO Panel Formwork Item no. Weight kg ,200 Outside Corner MXA 60 x m². Panel with plywood 18 mm. For 90 outside corners ,900 Outside Corner MXA 60 x m². Panel with plywood 18 mm. For 90 outside corners ,900 Panel MX 30 x m². Panel with plywood 18 mm ,350 Alignment Coupler BFD, galv. For all panel connections of MAXIMO, TRIO and RUNDFLEX. Compensations up to 10 cm. Technical Data Permissible tension force 20.0 kn. max ,800 Compensation Waler MAR 85-2 For fillers, height extensions, stopend formworks and special uses with MAXIMO. With captive connection components. Technical Data Permissible bending moment 3.9 knm

47 MAXIMO Panel Formwork Item no. Weight kg ,000 Compensation Waler MAR For fillers, height extensions, stopend formworks and special uses with MAXIMO. With captive connection components. Technical Data Permissible bending moment 3.9 knm ,520 Waler 85 Equivalent to Compensation Waler TAR 85 without mounting hooks. Technical Data Permissible bending moment 4.4 knm ,375 Hook Tie Head DW 15, galv. For connection of accessories to MAXIMO and TRIO panels. Thread DW 15. Technical Data Permissible tension force 20.0 kn Ø ,769 Hook Tie DW 15 l = 400, galv. For connection of accessories to MAXIMO and TRIO panels. Thread DW 15. Technical Data Permissible tension force 20.0 kn DW ,140 Stopend Tie TS, galv. For transmitting force from stopends into MAXIMO and TRIO panels. Thread DW 15. Technical Data Permissible tension force 20.0 kn. DW

48 MAXIMO Panel Formwork Item no. Weight kg ,000 Bulkhead Tie MX DW 20 For forming wall offsets with MAXIMO in connection with the Multi-Purpose Panel MXM ,310 Brace Connector TRIO, galv. For connection of push-pull props and kickers to MAXIMO and TRIO panels. For mounting to horizontal and vertical struts. Complete with 1 x Pin Ø 16 x 42, galv. 1 x Cotter Pin 4/1, galv ,430 Push-Pull Spreader MX For use with foundation formwork up to 1.20 m high and as a substitute for the top anchor with the MAXIMO 330. Complete with 1 x x Cotter Pin 4/1, galv. Note Adjustable in 0.5 cm increments from 15 to 30 cm, and in 1 cm increments from 30 to 40 cm. Technical Data Permissible tension and compression force 9 kn. Ø13, ,068 Stacking Device MX For easy stacking of MAXIMO panels

49 MAXIMO Panel Formwork Item no. Weight kg ,490 Stacking Device MAXIMO For stacking and shifting of 2-5 MAXIMO or TRIO panels of any size. Suitable for crane and fork-lift transportation. 4 pieces per stack. Safety instructions Follow Instructions for Use. Load-bearing capacity: 500 kg per device, 2 t per stack ,740 Lifting Hook MAXIMO 1.5 t For lifting of MAXIMO and TRIO panels. Safety instructions Always use 2 pieces per transportation unit. Follow Instructions for Use. Load-bearing capacity: Steel panels 1.5 t Alu panels 750 kg , Lifting Gear-3 TRIO For transportation of MAXIMO and TRIO panel stacks. Safety instructions Follow Instructions for Use!

50 MAXIMO Panel Formwork Item no. Weight kg ,800 Scaffold Bracket TRG 80 For mounting a working and concreting scaffold on MAXIMO and TRIO. For mounting to horizontal and vertical struts. Note Secured automatically when mounted. Technical Data Permissble load 150 kg/m² at a max. width of influence of 1.35 m / / ,000 Concreting Platform TRIO x 270 Working and concreting scaffold for MAXIMO and TRIO. Mounted on the panel from above, complete with self-locking device. Note Always lift with 4-sling lifting gear. The crane lifitng points are marked in yellow for easy identification. Technical Data Permissible load capacity of 150 kg/m² ,520 Stripping Bar TRIO 1180 Ø26 48

51 MAXIMO Panel Formwork Item no. Weight kg , Connector SB-1,2 - MX/TR/D For assembling Brace Frame SB-1,2 to MAXIMO, TRIO and DOMINO panels. Safety instructions Load-bearing point load capacity 1.0 t with a crane sling angle min 1270 max ,368 2,400 0,414 1,250 Accessories Bolt Ø 19 x 165, galv. Hook Strap SB-1, 2 Bolt SB-MAXIMO, galv. Sleeve SB-MAXIMO, galv ,140 Connector SB-A, B, C - MX/TR/D For assembling SB-A0, A, B, C to MAXIMO, TRIO and DOMINO panels. Note One for each tie point ,368 0,433 1,250 Accessories Bolt Ø 19 x 165, galv. Bolt SB-MAXIMO, galv. Sleeve SB-MAXIMO, galv ,414 Bolt SB-MAXIMO, galv. For connecting MAXIMO panels with SB Brace Frames Ø ,250 Accessories Sleeve SB-MAXIMO, galv. 49

52 MAXIMO Panel Formwork Item no. Weight kg ,250 Sleeve SB-MAXIMO, galv. For connecting MAXIMO panels with SB Brace Frames. 83 Ø ,414 Accessories Bolt SB-MAXIMO, galv ,940 MX Tie For wall thicknesses cm. Note To make striking easier, spray with a release agent before every use. Technical Data Permissible tension force 90 kn ,060 MX Tie For wall thicknesses cm. Note To make striking easier, spray with a release agent before every use. Technical Data Permissible tension force 90 kn ,310 MX Tie For wall thicknesses cm. Note To make striking easier, spray with a release agent before every use. Technical Data Permissible tension force 90 kn

53 MAXIMO Panel Formwork Item no. Weight kg ,560 MX Wingnut Counternut for Tie MX. Technical Data Permissible tension force 90 kn ,900 MX Tie Rod Spanner-2 For easier release of MX ties ,004 Plug MXM Ø 21 For MAXIMO Multi-Purpose Panel MXM, Inside Corner 50/20, Outside Corner 90 and standard panels for single-sided use. Ø15 Ø21 Ø ,017 Plug MX Ø For sealing MX tie holes in the concrete. Ø ,057 Stopper MX 84 MF For sealing MX tie holes in the concrete. Note For use with pressing water (waterproof concrete). Test report available! ,043 Stopper MX 50 MF For sealing MX tie holes in the concrete. Note For use with non-pressing water

54 MAXIMO Panel Formwork Item no. Weight kg ,036 Stopper MX 50 OF For closing MX tie holes in the concrete if the flange should not be visible. Note For use with non-pressing water ,037 Stud Spanner MX For holding the Stopper MX 84 MF and MX 50 MF ,183 Magnet Cone MX 55 For use with MAXIMO. For use with Tie MX. Note For use with waterproof or architectural concrete. Install on both sides. Ø ,893 Accessories Magnet Cone Spanner MX ,265 DK Concrete Cone UNI 58/52 For closing tie points with DK Sealing Cone DW 15/55, DW 20/55, DW 26/55 and SK Tie Cone DW 15. Note Delivery unit: 50 pieces. Ø58,5 Ø ,893 Magnet Cone Spanner MX For removing the Magnet Cone MX

55 MAXIMO Panel Formwork Item no. Weight kg ,012 Cone MX DR 22 For the use of DW 15 Tie Rods. Suitable for Spacer Tube DR Ø ,055 DK Sealing Cone DW 20/55 For waterproof, fire-resistant and sound-absorbing tie points with Tie Rod DW 20. For use with Tube Rough 28. Note Delivery unit: 50 pieces Ø61,5 Ø28, ,077 Sealing Sleeve MX Ø 16 Ø36 Ø16,5 Ø ,011 Nut Sealing Sleeve MX Ø 16 Ø34 Ø ,080 Accessories Adhesive AN , 50 ml ,080 Adhesive AN , 50 ml Sufficient for approx. 75 pieces, Nut Sealing Sleeve MX Ø ,556 Spanner for Sealing Sleeve MX Ø 16 Ø

56 PERI Product Range Wall Formwork Panel Formwork Girder Formwork Circular Formwork Facade Formwork Brace Frame Climbing Systems Climbing Scaffold Self-Climbing System Climbing Protection Panel Platform Systems Column Formwork Square Rectangular Circular Scaffold, Stairways, Working Platforms Facade Scaffold Working Platform Weather Protection Roof Stairway Access Slab Formwork Panel Formwork Beam Grid Formwork Girder Formwork Slab Table Beam Formwork Bridge and Tunnel Formwork Cantilevered Parapet Carriage Cantilevered Parapet Platform Engineer s Construction Kit Shoring Systems Steel Slab Props Aluminium Slab Props Tower Systems Heavy-Duty Props Services Formwork Assembly Cleaning / Repairs Formwork Planning Software Statics Special Constructions Additional Systems Plywood Formwork Girders Stopend Systems Pallets Transportation Containers D e 02/2010 5ma Art.-Nr.: Copyright by PERI GmbH PERI GmbH Formwork Scaffolding Engineering P.O. Box Weissenhorn Germany Tel +49 (0) Fax +49 (0) info@peri.com