Bentley MicroStation V8i
|
|
- Darlene McBride
- 8 years ago
- Views:
Transcription
1 Bentley MicroStation V8i Bentley MicroStation V8i is a CAD program designed with the interoperability of software in mind. MicroStation is compatible with both DWG and DGN files, either preexisting or new, and has both 2D and 3D capabilities. When working with a DWG file, MicroStation enters DWG work mode, and limits use of some of its features that are not DWG compatible. If working in DWG work mode and a file is opened that is not DWG compatible, MicroStation will ignore, but still leave intact the incompatible components while still allowing work to be done in a DWG compatible fashion. 1. To open Bentley MicroStation V8i : Start All Programs Bentley MicroStation V8i (SELECT Series 3) then choose MicroStation V8i (SELECT Series 3). 2. Open a seed template from the C: drive. File Open Local Disk (C:) ProgramData Bentley MicroStation V8i (SELECTseries) WorkSpace System seed seed3d.dgn. This opens a 3D dgn file, if you desire a dwg-compatible file, you will need to choose a different seed file. Four different view windows will be open with labels at the top of each telling which view is shown. 3. Once the template is open, use save as under the file tab to save it to a source that you are able to write to (i.e. C:temp or a USB storage device). 4. Click the down carrot on the Solids Modeling tab on the left of the screen. Choose the slab solid icon. 5. A window will come up, make sure that Orthogonal is selected and that for axis, Points (AccuDraw) is chosen. If the AccuDraw is not included after points, toggle the AccuDraw function on by clicking this icon in the tool bar near the top of the screen: 6. Click a point in the Top view window to set the axis of your piece. Drag the pointer in the direction that you want the length of the piece to extend and type the specific length you want,
2 then click the mouse. This will set the length of the piece. Do the same for the width (dragging, entering the width, and click). For the height, simply type the desired height and click. For the example shown, the dimensions are 2x3x1. Click the X on the Slab Solid window to close the tool. 7. Now your slab is set, you can zoom in or out in any of the views by rolling the scroll wheel on the mouse in the view window you wish to zoom, or move around your workspace by clicking the scroll wheel, holding down and dragging the screen. 8. To round the edges on the end of the piece, use the fillet edges tool under the Solids Modeling tab: In the window that comes up, set the radius that you want for your fillet, then, in the isometric view, select the corner edge that you want rounded, it will turn yellow, click again to carry out the command. Do this same procedure to the next edge. In the example, a radius of 0.5 is used for both corners. Close the Fillet Edges window to exit the tool. 9. To put a hole through the slab, use the hole feature, it is found under the Feature Modeling tab:
3 10. In the Hole Feature window that comes up, choose the diameter and other specifications for the hole. Then click on the slab to select it as your object. It is easiest to work in the top view for this feature. A tentative sketch will guide you while placing your hole. To place the hole, the pointer will snap to the center of the end of the slab, click the mouse and let go then drag the mouse along the direction you want the hole to be and type in the distance you want the hole to be from the point where you clicked and then click again. The whole is now placed through the slab. The example hole has a radius of 0.5 and is centered lengthwise and widthwise on the piece. Close the Hole Feature window. 11. To change the display style and add shading, click and hold the view display mode icon in the isomeric view window until a drop down menu appears, choose Illustration with Shadows.
4 12. Before adding dimensions, you ll need to create some settings. Click on Element Dimension Styles, in the window that comes up, click the Create Style icon: and name your style what you wish. Then, in the tabs to the right, set the amount of decimal places and units (under Units), the size of the font (under Text), and other adjustments you want. Then, make sure your style is selected and click the Set Style Active icon: and close the window. To add dimensions, click Tools Dimensions Dimension Element. Hold the mouse over the section that you want to add a dimension for, it will turn purple. Click on the section and drag the dimension away from the piece and place it where you wish. Repeat for the remaining sections.
5 13. To print the part, go to File Print. In the new window, there will be options and a preview of what will be printed. By default view that you had active will be the one previewed, to change this, choose the view you want to print from the View drop down. With the print window open, you can roll the mouse over the active view and use the scroll wheel to zoom in or out to your liking, then to update the preview click the Update from View button. Once all of the settings are correct, click the printer icon to print the piece.
PLAY VIDEO. Close- Closes the file you are working on and takes you back to MicroStation V8i Open File dialog.
Chapter Five Menus PLAY VIDEO INTRODUCTION To be able to utilize the many different menus and tools MicroStation V8i offers throughout the program and this guide, you must first be able to locate and understand
More informationIntroduction to Autodesk Inventor for F1 in Schools
F1 in Schools race car Introduction to Autodesk Inventor for F1 in Schools In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital Prototyping strategy
More informationIntroduction to Autodesk Inventor for F1 in Schools
Introduction to Autodesk Inventor for F1 in Schools F1 in Schools Race Car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s digital prototyping strategy
More informationA Practical Guide for Using MicroStation V8i Select Series 2
A Practical Guide for Using MicroStation V8i Select Series 2 CADD and Engineering Innovation Updated May 17, 2011 4201 E Arkansas Avenue Denver, CO 80222 (303) 512-5204 http://www.dot.state.co.us/designsupport/
More informationLAB 3-3D View Control
Chapter Objectives: After completing this exercise you will know how to: Check the elevation of an element Rotate a view using the rv= keyin Rotate a view using the 3-point method Rotate a view by element
More informationIntro to Excel spreadsheets
Intro to Excel spreadsheets What are the objectives of this document? The objectives of document are: 1. Familiarize you with what a spreadsheet is, how it works, and what its capabilities are; 2. Using
More informationPractice Workbook. QuickStart for Roadway Modeling Using OpenRoads
Practice Workbook This workbook is designed for use in Live instructor-led training and for OnDemand selfstudy. The explanations and demonstrations are provided by the instructor in the classroom, or in
More informationSpaceClaim Introduction Training Session. A SpaceClaim Support Document
SpaceClaim Introduction Training Session A SpaceClaim Support Document In this class we will walk through the basic tools used to create and modify models in SpaceClaim. Introduction We will focus on:
More informationTABLE OF CONTENTS. INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE...
Starting Guide TABLE OF CONTENTS INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE... 7 ADVANCE CONCRETE USER INTERFACE... 7 Other important
More information2013 Getting Started Guide
2013 Getting Started Guide The contents of this guide and accompanying exercises were originally created by Nemetschek Vectorworks, Inc. Vectorworks Fundamentals Getting Started Guide Created using: Vectorworks
More information4 Manipulating Elements
4 Manipulating Elements In the context of this course, Manipulation of elements means moving, copying, rotating, scaling and some other similar operations. We will find that manipulations are always a
More informationCDOT Monumentation Sheets
CDOT Monumentation Sheets This document describes the process used to assemble a Right of Way Monumentation Sheet. An InRoads XML report is used to display the required data from the geometry project.
More informationGenerative Drafting. Page 1 1997 2001 DASSAULT SYSTEMES. IBM Product Lifecycle Management Solutions / Dassault Systemes
Generative Drafting Page 1 Tutorial Objectives Description This Tutorial is an introduction to Generative Drafting. Message To show how CATIA V5 allows the user to automatically generate associative drafting
More informationCreating Fill-able Forms using Acrobat 8.0: Part 1
Creating Fill-able Forms using Acrobat 8.0: Part 1 The first step in creating a fill-able form in Adobe Acrobat is to generate the form with all its formatting in a program such as Microsoft Word. Then
More informationWhat s New V 11. Preferences: Parameters: Layout/ Modifications: Reverse mouse scroll wheel zoom direction
What s New V 11 Preferences: Reverse mouse scroll wheel zoom direction Assign mouse scroll wheel Middle Button as Fine tune Pricing Method (Manufacturing/Design) Display- Display Long Name Parameters:
More informationLayout Tutorial. Getting Started
Getting Started Layout Tutorial This tutorial will explain how create a layout template, send views to a layout page, then save the document in PDF format. In this tutorial you will learn about: Creating
More informationGuide To Creating Academic Posters Using Microsoft PowerPoint 2010
Guide To Creating Academic Posters Using Microsoft PowerPoint 2010 INFORMATION SERVICES Version 3.0 July 2011 Table of Contents Section 1 - Introduction... 1 Section 2 - Initial Preparation... 2 2.1 Overall
More informationMET 306 Activity 6. Using Pro/MFG Milling Operations Creo 2.0. Machining a Mast Step
Using Pro/MFG Milling Operations Creo 2.0 Machining a Mast Step If the Trim option is grayed out when trimming the mill volume, Save (making sure the.asm file is going to the correct subdirectory), Exit
More informationLEGO Digital Designer 4.3 User Manual
LEGO Digital Designer 4.3 User Manual The Readme file contains system requirements and the latest information about this software release. Please refer to it first if you encounter any problems. Contents
More information2. More Use of the Mouse in Windows 7
65 2. More Use of the Mouse in Windows 7 The mouse has become an essential part of the computer. But it is actually a relatively new addition. The mouse did not become a standard part of the PC until Windows
More informationBarcode Support. Table of Contents
Barcode Support Table of Contents Barcode Scanning and Labeling Support... 2 Scanning in Barcodes... 2 Basic Scanning Techniques... 2 Quick Barcode Scanning... 2 Using the Quick Find Fields with Scanners...
More informationPart Number: PMT1080-ENG Rev. 1
2010 Dassault Systèmes, All Rights Reserved DraftSight and the DraftSight logos are trademarks of Dassault Systèmes or its subsidiaries in the US and/or other countries. Other brand or product names are
More informationSage Accountants Business Cloud EasyEditor Quick Start Guide
Sage Accountants Business Cloud EasyEditor Quick Start Guide VERSION 1.0 September 2013 Contents Introduction 3 Overview of the interface 4 Working with elements 6 Adding and moving elements 7 Resizing
More informationAutodesk Fusion 360 Badge Guide: Design an F1 in Schools Trophy
Autodesk Fusion 360 Badge Guide: Design an F1 in Schools Trophy Abstract: Gain basic understanding of creating 3D models in Fusion 360 by designing an F1 in Schools trophy. This badge may be claimed by
More informationGetting Started With DraftSight A Guide For AEC Users
Getting Started With DraftSight A Guide For AEC Users DraftSight.com Facebook.com/DraftSight Welcome to DraftSight a valuable tool for any AEC professional! DraftSight is more than a free, professional-grade
More informationChapter 23: Drafting in Worksheet View
Chapter 23: Drafting in Worksheet View Worksheet View is a powerful, 2D production drafting module. Here you can find all of the drawing and editing tools needed to create fast, accurate, detailed working
More informationManual. OIRE Escuela de Profesiones de la Salud. Power Point 2007
Power Point 2007 Manual OIRE Escuela de Profesiones de la Salud Power Point 2007 2008 The New Power Point Interface PowerPoint is currently the most common software used for making visual aids for presentations.
More informationGetting to know Windows 8
Getting to know Windows 8 Queen Mary student desktop Sign In & Sign Out Sign in: Please enter your Queen Mary username and password when prompted. Sign out: There are two easy ways to sign out: From the
More informationOrtelia Space Builder User Manual
Ortelia Space Builder User Manual http://ortelia.com 1 Table of Contents Introducing Ortelia Space Builder... 2 System Requirements... 3 1. Operating system:... 3 2. Hardware:... 3 Minimum Graphics card
More informationCREATING EXCEL PIVOT TABLES AND PIVOT CHARTS FOR LIBRARY QUESTIONNAIRE RESULTS
CREATING EXCEL PIVOT TABLES AND PIVOT CHARTS FOR LIBRARY QUESTIONNAIRE RESULTS An Excel Pivot Table is an interactive table that summarizes large amounts of data. It allows the user to view and manipulate
More informationGETTING STARTED WITH DIALux (A Very Rough Guide) Rev. 6
1. Scaling your project drawing for import into DIALux using AutoCAD 2004 OR DraftSight, (procedure is similar in AutoCAD 2014 but you will need to access the commands through the ribbon interface): a)
More informationBarcode Labels Feature Focus Series. POSitive For Windows
Barcode Labels Feature Focus Series POSitive For Windows Inventory Label Printing... 3 PFW System Requirement for Scanners... 3 A Note About Barcode Symbologies... 4 An Occasional Misunderstanding... 4
More informationHouse Design Tutorial
Chapter 2: House Design Tutorial This House Design Tutorial shows you how to get started on a design project. The tutorials that follow continue with the same plan. When we are finished, we will have created
More informationPro/ENGINEER Wildfire 4.0 Basic Design
Introduction Datum features are non-solid features used during the construction of other features. The most common datum features include planes, axes, coordinate systems, and curves. Datum features do
More informationIntroduction to CATIA V5
Introduction to CATIA V5 Release 16 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com
More informationThe CAD interface is comprised of two different screens: the graphic/drawing screen and the text screen.
That CAD Girl J ennifer dib ona Website: www.thatcadgirl.com Email: jennifer@thatcadgirl.com Phone: (919) 417-8351 Fax: (919) 573-0351 Overview of AutoCAD or IntelliCAD with Carlson Software Screens and
More informationSolidworks Lesson 6 - Assembly & Part Drawings. UCF Engineering
Solidworks Lesson 6 - Assembly & Part Drawings UCF Engineering Mechanical Drawings So far we have been dealing with creating parts and assemblies in SolidWorks, however, when you go to get a part machined,
More informationMicroStation Tips & Tricks
MicroStation Tips & Tricks % keyin - Used to start another Windows application %pipespecs.doc %calc ALT+DATA to Match - To quickly match an elements level, color, line style or line weight: hold the pointer
More informationCreating and Using Links and Bookmarks in PDF Documents
Creating and Using Links and Bookmarks in PDF Documents After making a document into a PDF, there may be times when you will need to make links or bookmarks within that PDF to aid navigation through the
More informationBasic 2D Design Be sure you have the latest information!
Basic 2D Design mastercam x getting started tutorials Basic 2D Design December 2011 Be sure you have the latest information! Information might have been changed or added since this document was published.
More informationChapter 30: How to import a DWG drawing not created with MasterChef
Chapter 30: How to import a DWG drawing not created with MasterChef Launch MasterChef from the icon on your desktop. Note: If you are using a demo version, once loaded the program, a message will notify
More informationPC Advanced with Windows 8
PC Advanced with Windows 8 Mercer County Library System Brian M. Hughes, County Executive Action 1. Start Screen Technique The Windows 8 Start Screen which is an extended version of the Start Button s
More informationCreating Forms with Acrobat 10
Creating Forms with Acrobat 10 Copyright 2013, Software Application Training, West Chester University. A member of the Pennsylvania State Systems of Higher Education. No portion of this document may be
More informationLogbook Entry Creator Program
Aircraft Maintenance Logbook Entries Made Easy Logbook Entry Creator Program Instruction Manual www.ronsaviationsoftware.com Rons Aviation Software V1.2 The log book entry creator program is designed to
More informationRev9 TOPCON Global Marketing Group
Quick Start Guide Rev9 TOPCON Global Marketing Group 1/18 The flow of Data Processing 1-1 Create a new project Obtain data by remote-controlling the GLS-1000 Obtain data by standalone 2-A-1 Connect PC
More informationExcel 2007 Basic knowledge
Ribbon menu The Ribbon menu system with tabs for various Excel commands. This Ribbon system replaces the traditional menus used with Excel 2003. Above the Ribbon in the upper-left corner is the Microsoft
More informationPro/ENGINEER Wildfire 3.0 Tips
Pro/ENGINEER Wildfire 3.0 Tips W. Durfee Keyboard/mouse shortcuts CTRL+D Default view Middle-Button Spin SHIFT+Middle Pan CTRL+Middle Zoom (press, drag up-down) CTRL+Middle Turn (press, drag left-right)
More informationUnderstand the Sketcher workbench of CATIA V5.
Chapter 1 Drawing Sketches in Learning Objectives the Sketcher Workbench-I After completing this chapter you will be able to: Understand the Sketcher workbench of CATIA V5. Start a new file in the Part
More informationUser Tutorial on Changing Frame Size, Window Size, and Screen Resolution for The Original Version of The Cancer-Rates.Info/NJ Application
User Tutorial on Changing Frame Size, Window Size, and Screen Resolution for The Original Version of The Cancer-Rates.Info/NJ Application Introduction The original version of Cancer-Rates.Info/NJ, like
More informationSolidWorks: Mirror, Revolve, and. Introduction to Robotics
SolidWorks: Mirror, Revolve, and Circular Pattern Introduction to Robotics Let s Review At this point we have learned the following: Extrude Boss/Base Extruded Cut Adding Relations and Dimensions Linear
More informationChapter 1. Creating Sketches in. the Sketch Mode-I. Evaluation chapter. Logon to www.cadcim.com for more details. Learning Objectives
Chapter 1 Creating Sketches in Learning Objectives the Sketch Mode-I After completing this chapter you will be able to: Use various tools to create a geometry. Dimension a sketch. Apply constraints to
More informationHow to use Wireframe in Visio
Visio Tutorial: How to use Wireframe How to use Wireframe in Visio By Derek Tobler Table of Contents Getting started... 2 To start go to the Start icon and click on it. Then type Visio in the Search programs
More informationSoftware User's Guide
Software User's Guide Brother QL-series The contents of this guide and the specifications of this product are subject to change without notice. Brother reserves the right to make changes without notice
More informationYouthQuest Quick Key FOB Project
YouthQuest Quick Key FOB Project This project is designed to demonstrate how to use the 3D design application, Moment of inspiration, to create a custom key fob for printing on the Cube3 3D printer. Downloading
More informationIDOT Getting Around Illinois Interactive Map Quick Reference Guide
IDOT Getting Around Illinois Interactive Map Quick Reference Guide 1 2 3 4 5 6 7 8 9 10 1) Navigation Tools The Navigation tools are used to reposition the visible area on the map display. Zoom In Clicking
More informationPrinting Solutions for Word 2013. Printing Solutions for Word 2010. Printing Solutions for Word 2007. Printing Solutions for Word 2003
Printing Solutions for Word 2013 Printing Solutions for Word 2010 Printing Solutions for Word 2007 Printing Solutions for Word 2003 Printing solutions for Printers Word 2013 sure you have selected the
More informationEdline Manual Design Guide Version: September 2011
Edline Manual Design Guide Version: September 2011 Copyright Statements: Edline software is a trademark of Edline. Copyright 2011. Microsoft Windows names and logos are registered trademarks of the Microsoft
More informationCADVANCE Release Notes for V15
CADVANCE Release Notes for V15 This document describes what is new and improved for CADVANCE V15. These release notes should provide all the information needed to get you started with this release. Updated
More information7 Enclosed Areas. When you have completed this chapter, you will be able to:
7 Enclosed Areas Our designs so far have consisted entirely of open linework, except for a brief introduction to Fill Attributes on page 3-15. Closed linework may delineate an Area, such as a section of
More informationStrikeRisk v6.0 IEC/EN 62305-2 Risk Management Software Getting Started
StrikeRisk v6.0 IEC/EN 62305-2 Risk Management Software Getting Started Contents StrikeRisk v6.0 Introduction 1/1 1 Installing StrikeRisk System requirements Installing StrikeRisk Installation troubleshooting
More informationSnap 9 Professional s Scanning Module
Miami s Quick Start Guide for Using Snap 9 Professional s Scanning Module to Create a Scannable Paper Survey Miami s Survey Solutions Snap 9 Professional Scanning Module Overview The Snap Scanning Module
More informationShipment Label Header Guide
Shipment Label Header Guide This guide will walk you through the 3 main phases of setting up a shipment label header within World Ship 2013. This guide was made using standard Windows Microsoft Office
More informationCustomizing forms and writing QuickBooks Letters
LESSON 15 Customizing forms and writing QuickBooks Letters 15 Lesson objectives, 398 Supporting materials, 398 Instructor preparation, 398 To start this lesson, 398 About QuickBooks forms, 399 Customizing
More informationWhat s New in QuarkXPress 8
What s New in QuarkXPress 8 LEGAL NOTICES 2008 Quark Inc. as to the content and arrangement of this material. All rights reserved. 1986 2008 Quark Inc. and its licensors as to the technology. All rights
More informationLinkage 3.2. User s Guide
Linkage 3.2 User s Guide David Rector Wednesday, April 06, 2016 Table of Contents Table of Contents... 2 Installation... 3 Running the Linkage Program... 3 Simple Mechanism Tutorial... 5 Mouse Operations...
More information10.0-2. Finite Element Modeling
What s New in FEMAP FEMAP 10.0 and 10.0.1 include enhancements and new features in: User Interface on page 3 Meshing on page 23 Mesh Associativity on page 33 Properties on page 33 Functions on page 35
More informationIf you know exactly how you want your business forms to look and don t mind detail
Advanced Form Customization APPENDIX E If you know exactly how you want your business forms to look and don t mind detail work, you can customize QuickBooks forms however you want. With QuickBooks Layout
More informationEpson Brightlink Interactive Board and Pen Training. Step One: Install the Brightlink Easy Interactive Driver
California State University, Fullerton Campus Information Technology Division Documentation and Training Services Handout Epson Brightlink Interactive Board and Pen Training Downloading Brightlink Drivers
More informationWindows 8 Features (http://www.dummies.com/how-to/content/windows-8-for-dummies-cheat-sheet.html)
Windows 8 Features (http://www.dummies.com/how-to/content/windows-8-for-dummies-cheat-sheet.html) Five Big Changes in Windows 8 Windows 8 looks and behaves much differently from previous versions of Windows.
More informationGetting Started in Tinkercad
Getting Started in Tinkercad By Bonnie Roskes, 3DVinci Tinkercad is a fun, easy to use, web-based 3D design application. You don t need any design experience - Tinkercad can be used by anyone. In fact,
More informationQuickstart Tutorial. Bradford Technologies, Inc. 302 Piercy Road, San Jose, California 95138 800-622-8727 fax 408-360-8529 www.bradfordsoftware.
Quickstart Tutorial A ClickFORMS Tutorial Page 2 Bradford Technologies. All Rights Reserved. No part of this document may be reproduced in any form or by any means without the written permission of Bradford
More informationAutodesk Fusion 360: Assemblies. Overview
Overview In this module you will learn how different components can be put together to create an assembly. We will use several tools in Fusion 360 to make sure that these assemblies are constrained appropriately
More informationChapter 4: Website Basics
1 Chapter 4: In its most basic form, a website is a group of files stored in folders on a hard drive that is connected directly to the internet. These files include all of the items that you see on your
More informationPresents. AccuDraw. Instructor Pam Roberts pamroberts@cadassist.com www.cadassist.com
Presents AccuDraw Instructor Pam Roberts pamroberts@cadassist.com www.cadassist.com ACCUDRAW AccuDraw gives user an easy way to input accurate points. By default with MicroStation V8 AccuDraw will automatically
More informationFile Management Windows
File Management Windows : Explorer Navigating the Windows File Structure 1. The Windows Explorer can be opened from the Start Button, Programs menu and clicking on the Windows Explorer application OR by
More informationTable of Contents. Part I Welcome. Part II Introduction. Part III Getting Started. Part IV The User Interface. Part V Quick Start Tutorials
Contents I Table of Contents Part I Welcome 5 Part II Introduction 5 1 Overview... 5 2 Product... Levels 5 3 Technical... Support 6 4 Copyright... 7 Part III Getting Started 7 1 Installation... 7 2 Register...
More informationAvery DesignPro 2000 User Guide
Avery DesignPro 2000 User Guide Creating labels and cards for your personal needs is easy with Avery DesignPro 2000 Avery DesignPro 2000 User Guide First edition of the condensed user manual for Avery
More informationHands On Exercise Using the SHA Detail Model (Bridge)
Let s look at an example: Hands On Exercise Using the SHA Detail Model (Bridge) In this exercise, the standard shadetail2d.dgn has been used to create a new file (pbr- BD01_chapter2.dgn). Additional elements
More informationCREATING POSTERS WITH POWERPOINT
CREATING POSTERS WITH POWERPOINT PowerPoint files will be required for Posters on CD-Rom with very few exceptions. WHY POWERPOINT? Although there are many software programs that will create posters, PowerPoint
More informationCreating a Poster Presentation using PowerPoint
Creating a Poster Presentation using PowerPoint Course Description: This course is designed to assist you in creating eye-catching effective posters for presentation of research findings at scientific
More informationDinoXcope User Manual
DinoXcope User Manual Contents 1 System Requirements 1 Installation 2 Adding a time stamp to the live view 3 Capturing an image 4 Creating a real time movie 5 Creating a time-lapse movie 6 Drawing on an
More informationHow to Edit an Email. Here are some of the things you can do to customize your email:
How to Edit an Email Editing a new email created during the Create an Email wizard or editing an existing email in the Edit Email section of the Manage Emails tab is easy, using editing tools you re probably
More informationFlash MX Image Animation
Flash MX Image Animation Introduction (Preparing the Stage) Movie Property Definitions: Go to the Properties panel at the bottom of the window to choose the frame rate, width, height, and background color
More informationUsing Mail Merge to Create Form Letters and Labels
Using Mail Merge to Create Form Letters and Labels 1. Open the word document on your floppy: Practice letter 2. Go to Tools > Mail Merge. The Mail Merger Helper appears. We are going to create form letters,
More informationSection #13 Pictorial Table Of Contents. The Caster. Top & Bottom Shelves. Pages 617-623 Page 624 Page 625 Pages 626-628 Pages 629-633
AQX Introduction Section # Pictorial Table Of Contents Completed Shop Cart Step-by-Step Tutorial The Caster The Leg Fractional The Lower Cross Member Machining w/ Access Holes AutoQuoterX Page 610 Page
More informationTorchmate CAD User s Guide
Torchmate CAD User s Guide Revised May 2011 Table of Contents: Overview of the Manual Installation and Setup Important Configuration Changes Overview of Menus Navigation and Selection Methods Basic CAD
More informationLayout Tutorial. Chapter 10: Getting Started
Chapter 10: Layout Tutorial In this tutorial we will create a layout template, send a few views to a layout page, then save this document in PDF format. In this tutorial you will learn about: Creating
More informationHOW TO VIEW AND EDIT PICTURES
Get started Shutterfly can help you make your pictures look their best. We re going to show you the different ways to view and edit your pictures using our easy-to-use tools. To begin, sign in to your
More informationLearning Services IT Guide. Access 2013
Learning Services IT Guide Access 2013 Microsoft Access is a programme which allows you to store a lot of information easily in the form of a database. For example you could create a database which stored
More information11 Printing Designs. When you have completed this chapter, you will be able to:
11 Printing Designs Creating printed documents is the end we have worked towards from the beginning of this course. We have already been introduced to it very briefly with Printing - A First Look on page
More informationExcel 2003 Tutorial I
This tutorial was adapted from a tutorial by see its complete version at http://www.fgcu.edu/support/office2000/excel/index.html Excel 2003 Tutorial I Spreadsheet Basics Screen Layout Title bar Menu bar
More informationMicrosoft Access 2010 Overview of Basics
Opening Screen Access 2010 launches with a window allowing you to: create a new database from a template; create a new template from scratch; or open an existing database. Open existing Templates Create
More informationSoftware for Producing Rack Layouts and Purchase Orders
1 Software for Producing Rack Layouts and Purchase Orders Welcome to RackTools: software that makes it simple and quick to specify Middle Atlantic Products. RackTools has been designed with one purpose
More informationTABLE OF CONTENTS. INTRODUCTION... 5 Advance Steel... 5 Where to find information?... 6
Starting Guide TABLE OF CONTENTS INTRODUCTION... 5 Advance Steel... 5 Where to find information?... 6 INSTALLATION... 6 System requirements... 6 Starting the installation... 6 STARTING ADVANCE STEEL...
More informationSolidWorks Tutorial 3 MAGNETIC BLOCK
SolidWorks Tutorial 3 MAGNETIC BLOCK Magnetic Block In this exercise you will make a magnetic block. To do so, you will create a few parts, which you will assemble. You will learn the following new applications
More informationChapter 9. Editing Features. Learning Objectives
Chapter 9 Editing Features Learning Objectives After completing this chapter, you will be able to: Edit features. Edit sketches of the sketch based features. Edit the sketch plane of the sketch based features.
More informationVarious MicroStation Tips and Tricks MicroStation (SELECTseries 3) Tine Lai Andersen, LEARNing Consultant
Various MicroStation Tips and Tricks MicroStation (SELECTseries 3) Tine Lai Andersen, LEARNing Consultant MicroStation Tips and tricks At the end of this training session, an assessment will be given.
More informationIntroduction to dobe Acrobat XI Pro
Introduction to dobe Acrobat XI Pro Introduction to Adobe Acrobat XI Pro is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License. To view a copy of this
More informationSketchUp Instructions
SketchUp Instructions Every architect needs to know how to use SketchUp! SketchUp is free from Google just Google it and download to your computer. You can do just about anything with it, but it is especially
More informationIntroduction. Purpose of this Module. Objectives of this Module
Introduction Welcome to the module series. This module is your first step toward learning how to complete various details of your project in 3D using the Bentley InRoads software. Purpose of this Module
More information