Chapter 30: How to import a DWG drawing not created with MasterChef
|
|
- Oscar Page
- 8 years ago
- Views:
Transcription
1 Chapter 30: How to import a DWG drawing not created with MasterChef Launch MasterChef from the icon on your desktop. Note: If you are using a demo version, once loaded the program, a message will notify the remaining days of the evaluation period. If you are in possession of the licence of the software, make sure you have inserted and installed the USB hardware key that came with the licence to use the software. From the main screen of the PDM module of MasterChef you double-click on the plan using the menu on the left side or the the central grid part containing the list of projects already created. Pag. 1
2 Before creating the new MasterChef drawing where you will import the DWG plan not created with MSC, it is necessary to open the original file and recover some necessary information: the scale and the unit of measurement. Open the DWG file that you want to import and, using the DISTANCE command of your CAD engine, measure the width of a window or a door to verify if the drawing has been created in meters, centimeters, millimeters, inches.. In this case the drawing to import has been created in meters because the calculated distance is Pag. 2
3 Now run the command UNITS of your CAD engine, writing in the command line _DDUNITS, in order to set the correct unit of measurement of the drawing. In fact the unit of measurement is often not defined, set to Unitless, or the one which has been defined is not the correct one. Based on the verification you did using the DISTANCE command, choose meters as insertion scale in the center of the window. If the drawing you are going to import has been created in centimeters or millimeters (i.e. 75 cm or 750 mm) set the correct unit. Confirm your modifications clicking on OK, then close and save the original drawing and also the CAD engine. Go back to you project in the PDM module of MasterChef. Note: In this way we didn t modify anything in the original drawing, we have only changed the information about the DWG unit of measurement. The drawing still has its original characteristics, it will be not necessary to change its scale in order to use the MasterChef commands, because it will be inserted as block inside a new MasterChef drawing. Pag. 3
4 Select the project where you want to add shown here below click on the button the new DWG (as explained in the previous chapters) and in the tool bar and select Add a new DWG to an existing plan. MasterChef will automatically open the CAD environment to start your project. In the window that opens insert the drawing data (name, title, etc) In the end click on the green button and the CAD engine will open automatically. Pag. 4
5 In the CAD tolbar choose INSERT > BLOCK. Clicking on the BROWSE button load the DWG file you want to import. At the bottom right you can see all the information about the unit of the drawing that will be inserted as a block. On the basis of this unit of measurement the CAD will calculateautomatically the scale factor to convert the imported block according to the unit of measurement of the current drawing. In this case the original drawing has been created in meters while the MasterChef project is in millimeters. Then the scale factor proposed to convert meters to millimeters will be Make sure you have checked the options Insertion point: Specify On-screen and Explode on the left. Click on the OK button to confirm. Click anywhere inside your MasterChef drawing in order to insert the imported block. Pag. 5
6 At the end click on PLAN VIEW button in the MasterChef toolpalette to display the whole drawing. To verify if the import has been done correctly measure the width of the same window or door you had measured before in the original drawing. Now the size is expressed in millimeters (in this case 750 mm). Pag. 6
7 Click on the PLAN VIEW button in the MasterChef toolpalette to display the whole drawing. All the layers used in the original drawing have been imported and added in the layers list of MasterChef. In this specific case the drafter of the original project has correctly categorized each object by type (walls, doors, windows, pillars, stairs) using customized layers. Often in the imported drawing all the objects are on the same layer. As the most important thing is to get the wall plan, we suggest you to change the layer for all the other items (frames, fixtures, etc.). Note: Make sure also that the wall entities are lines. In fact the MasterChef command for the creatin of 3D walls can work only with line entities placed on layer 400-Walls-2D. Otherwise you can use the EXPLODE commmand of the CAD engine to convert all the entities to lines. From the Architectural toolpalette of MasterChef run the command CONVERT LAYERS. This command permits you to move all the entites from a generic layer to a layer of MasterChef. In our case we use this command to move all walls from the original layer WALLS to the layer for 2D walls of MasterChef: 400-Walls-2D. Pag. 7
8 From the list of the generic layers on the left select the layer corresponding to 2D walls (in our case WALLS). From the list of MasterChef layers on the right select the layer 400-Walls-2D and click on the button LINK. The click on OK to confirm. As you can see all the 2D walls have changed their color because their entities have been placed on the layer 400- Walls-2D. Pag. 8
9 Before extruding the 2D walls to create the 3D you have to insert the fixtures, because the already existing ones in the original drawing are only simple CAD 2D items. Click on the button FIXTURES in the Architectural MasterChef toolpalette. In the window that opens, first of all you have to chooes the fixture type that you want to insert from the list on the right: Window Door Hole Niche Goods-lift Select WINDOW. Click on the preview image of the window to open the library and choose the first type. Cofirm clicking on OK to close the library. Make sure you have checked the following options: Height: mm Height from ground: mm Set Width on the Screen Set Thickness on the Screen At the end click on OK Pag. 9
10 Using the ZOOM command enlarge the space where you want to insert the window in order to define better the workspace. Then click on one of the internal corner of the opening to set the insertion point of the window. Now you have to specify the window width. From the insertion point move to the opposite internal corner and click on it. Finally you have to specify the window thickness that corresponds to the wall thickness. From the insertion point move to the upper corner and click on it. Repeat this command in the same way to insert the other doors and windows. When you have finished inserting the MasterChef fixture, you can deactivate or freeze the original layers. Pag. 10
11 From the Architectural toolpalette of MasterChef run the command EXTRUDE WALLS 2D. The software will ask you if you want to extrude all 2D walls or to select only some entities to create 3D. Press ENTER on your keyboard to extrude all 2D walls. Set the roof height: Roof Height: mm Press again ENTER to confirm. Pag. 11
12 Use the ISOMETRIC VIEWS MasterChef command to change the point of view and display your drawing in 3D. Pag. 12
TABLE OF CONTENTS. INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE...
Starting Guide TABLE OF CONTENTS INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE... 7 ADVANCE CONCRETE USER INTERFACE... 7 Other important
More informationGenerative Drafting. Page 1 1997 2001 DASSAULT SYSTEMES. IBM Product Lifecycle Management Solutions / Dassault Systemes
Generative Drafting Page 1 Tutorial Objectives Description This Tutorial is an introduction to Generative Drafting. Message To show how CATIA V5 allows the user to automatically generate associative drafting
More informationHouse Design Tutorial
Chapter 2: House Design Tutorial This House Design Tutorial shows you how to get started on a design project. The tutorials that follow continue with the same plan. When we are finished, we will have created
More informationEnvisioneer Technical Note
Title Blocks By default there are four pre-defined Worksheet view windows available (Floor Plan, Elevations, Details, and Site Plan). Each one contains a generic border and title block supplied by Cadsoft.
More informationCongratulations on your purchase of a BPM Microsystems device programmer. Your new device programmer was designe d to provid e years of suppor t for
Congratulations on your purchase of a BPM Microsystems device programmer. Your new device programmer was designe d to provid e years of suppor t for thousand s of devices, with the use of optional socket
More informationGETTING STARTED WITH DIALux (A Very Rough Guide) Rev. 6
1. Scaling your project drawing for import into DIALux using AutoCAD 2004 OR DraftSight, (procedure is similar in AutoCAD 2014 but you will need to access the commands through the ribbon interface): a)
More informationSirona SIDEXIS Installation
Sirona SIDEXIS Installation The installation and configuration of Sopro inter-oral cameras with SIDEXIS version 2.3 is a three step process. The first step is to install the USB 2.0 driver and test the
More informationRestoring your Computer from a Backup in Windows 8 (File History)
Restoring your Computer from a Backup in Windows 8 (File History) Introduction 1. The File History tool in Windows 8 and Windows 8.1 is used to restore files and folders to your computer from a backup.
More informationConverting an AutoCAD Drawing into PDF File
Tutorial Created by Brijesh Bhatha, 2004. Updated 2006 by Corinne Stewart (corinnestewart@gmail.com) CP-208 Plan Preparation Studio - Prof. Elizabeth Macdonald 2 In this tutorial we will learn to create
More informationCREATING A 3D VISUALISATION OF YOUR PLANS IN PLANSXPRESS AND CORTONA VRML CLIENT
CREATING A 3D VISUALISATION OF YOUR PLANS IN PLANSXPRESS AND CORTONA VRML CLIENT 20-25 Minutes This topic is for users of PlansXpress Total Toolkit Edition. To upgrade to PlansXpress Total Toolkit, call
More informationSketchUp Instructions
SketchUp Instructions Every architect needs to know how to use SketchUp! SketchUp is free from Google just Google it and download to your computer. You can do just about anything with it, but it is especially
More informationIntroduction to AutoCAD 2007
Introduction to AutoCAD 2007 Alf Yarwood Chapter 10 Exercise 1 1. Open AutoCAD 2007 with a double-click on its shortcut icon in the Windows desktop. 2. Open the template acadiso.dwt. 3. Construct the drawing
More informationIntroduction to AutoCAD 2010
Page 1 Introduction to AutoCAD 2010 Alf Yarwood Chapter 10 Exercise 1 1. Open AutoCAD 2010 with a double-click on its shortcut icon in the Windows desktop. 2. Open the template acadiso.dwt. 3. Construct
More informationLayout Tutorial. Getting Started
Getting Started Layout Tutorial This tutorial will explain how create a layout template, send views to a layout page, then save the document in PDF format. In this tutorial you will learn about: Creating
More informationGetting Started With DraftSight A Guide For AEC Users
Getting Started With DraftSight A Guide For AEC Users DraftSight.com Facebook.com/DraftSight Welcome to DraftSight a valuable tool for any AEC professional! DraftSight is more than a free, professional-grade
More informationBentley MicroStation V8i
Bentley MicroStation V8i Bentley MicroStation V8i is a CAD program designed with the interoperability of software in mind. MicroStation is compatible with both DWG and DGN files, either preexisting or
More informationIntroduction to GIS functionality
Exercise Introduction to GIS functionality Step 1 Start ArcInfo If necessary, start ArcInfo. Click the Start button in your Windows 2000 Task Bar and select Programs. Click the ArcInfo program group and
More informationFlash MX Image Animation
Flash MX Image Animation Introduction (Preparing the Stage) Movie Property Definitions: Go to the Properties panel at the bottom of the window to choose the frame rate, width, height, and background color
More informationUse your mobile phone as Modem. Intel Easy Steps 1 2012 Intel Corporation All rights reserved.
Use your mobile phone as Modem Intel Easy Steps 1 2012 Intel Corporation Mobile phone as Modem Use your mobile phone as Modem In order to connect your computer to the internet you need to use the services
More informationIntroduction to Autodesk Inventor for F1 in Schools
Introduction to Autodesk Inventor for F1 in Schools F1 in Schools Race Car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s digital prototyping strategy
More informationHow to Attach Files in Blackboard Learn Email, Messages, Discussions, and Assignments
E-Mail 1. Launch the Email by clicking the icon from the Menu frame found on the left side of the screen. 2. From within the Send Email page, click the "Select Users" link. If you click any links above
More informationSolidWorks Building Blocks Tutorial. Toy-car
SolidWorks Building Blocks Tutorial Toy-car From the age of until the age of For use with SolidWorks Educational Release 2010-2011 This tutorial was developed for SolidWorks Worldwide and may be used by
More informationAutoCAD Architecture 2012 UK Content Tools
AutoCAD Architecture 2012 UK Content Tools Contents Contents... 1 Installation... 2 Loading the utilities... 2 Utilities Overview... 3 Menu and Toolbar... 3 Content Generation... 3 Content Publishing...
More informationWorkspaces Creating and Opening Pages Creating Ticker Lists Looking up Ticker Symbols Ticker Sync Groups Market Summary Snap Quote Key Statistics
Getting Started Workspaces Creating and Opening Pages Creating Ticker Lists Looking up Ticker Symbols Ticker Sync Groups Market Summary Snap Quote Key Statistics Snap Report Price Charts Comparing Price
More informationMicrosoft SharePoint 2010 End User Quick Reference Card
Microsoft SharePoint 2010 End User Quick Reference Card Microsoft SharePoint 2010 brings together the people, documents, information, and ideas of the University into a customizable workspace where everyone
More informationCreating a Poster in PowerPoint 2010. A. Set Up Your Poster
View the Best Practices in Poster Design located at http://www.emich.edu/training/poster before you begin creating a poster. Then in PowerPoint: (A) set up the poster size and orientation, (B) add and
More informationCODESOFT Installation Scenarios
CODESOFT Installation Scenarios NOTES: CODESOFT is a separate install from existing versions of CODESOFT. You will need to make note of your current settings (default directories, etc.) so you can duplicate
More informationActiView. Visual Presenter Image Software User Manual - English
ActiView Visual Presenter Image Software User Manual - English Date: 05/02/2013 Table of Contents 1. Introduction... 3 2. System Requirements... 3 3. Install ActiView - Windows OS... 4 4. Install ActiView
More informationCrop and Frame Your Photos
Crop and Frame Your Photos Paint Shop Pro s crop tool gives you total control over your photo compositions. Cropping allows you to turn busy portraits into professional prints. And when you have a nicely
More informationUnderstand the Sketcher workbench of CATIA V5.
Chapter 1 Drawing Sketches in Learning Objectives the Sketcher Workbench-I After completing this chapter you will be able to: Understand the Sketcher workbench of CATIA V5. Start a new file in the Part
More informationOverview... 2 How to Add New Documents... 3 Adding a Note / SMS or Phone Message... 3 Adding a New Letter... 4. How to Create Letter Templates...
THE DOCUMENT MANAGER Chapter 14 THE DOCUMENT MANAGER CONTENTS Overview... 2 How to Add New Documents... 3 Adding a Note / SMS or Phone Message... 3 Adding a New Letter... 4 How to Create Letter Templates...
More information2013 Getting Started Guide
2013 Getting Started Guide The contents of this guide and accompanying exercises were originally created by Nemetschek Vectorworks, Inc. Vectorworks Fundamentals Getting Started Guide Created using: Vectorworks
More informationIntroduction to Autodesk Inventor for F1 in Schools
F1 in Schools race car Introduction to Autodesk Inventor for F1 in Schools In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital Prototyping strategy
More informationSmart Board Notebook Software A guide for new Smart Board users
Smart Board Notebook Software A guide for new Smart Board users This guide will address the following tasks in Notebook: 1. Adding shapes, text, and pictures. 2. Searching the Gallery. 3. Arranging objects
More informationSoundLAB Software Download Software from the Bogen website: www.bogen.com/software
SPLM DIGITAL SOUND PRESSURE LEVEL METER SoundLAB Software INSTALLATION & INSTRUCTION MANUAL Download Software from the Bogen website: www.bogen.com/software Specifications are subject to change without
More informationCreating Your Personal Website
Creating Your Personal Website These instructions will show you how to create a personal webpage for CSULB students using Dreamweaver MX 2004. The page will consist of a title, background image, text,
More informationManaging Contacts in Outlook
Managing Contacts in Outlook This document provides instructions for creating contacts and distribution lists in Microsoft Outlook 2007. In addition, instructions for using contacts in a Microsoft Word
More informationUsing the enclosed installation diagram, drill three holes in the wall with the lower hole 1150mm from the floor.
Terminal Installation When choosing the location of the terminal, care should be taken to select an area with consistent light levels throughout the day and avoid areas where the unit may be subjected
More informationIES <Virtual Environment> Tutorial. ModelIT (Version 6.0)
IES Tutorial ModelIT (Version 6.0) 1 Introduction: ModelIT Tutorial This document shows you how to use ModelIT, IES s 3D building geometry modelling tool. The tutorial is intended
More informationDatabase Program Instructions
Database Program Instructions 1) Start your Comparative Rating software by double-clicking the icon on your desktop. 2) Click on the button on the Comparative Rating Software Main Menu. 3) A message Loading
More informationINSTALLING MÜSE UPDATES FOR ISTAN
INSTALLING MÜSE UPDATES FOR ISTAN System updates are available periodically and can be downloaded using any computer with an Internet connection. CAE Healthcare Instructor Workstations should NOT be connected
More informationOrtelia Space Builder User Manual
Ortelia Space Builder User Manual http://ortelia.com 1 Table of Contents Introducing Ortelia Space Builder... 2 System Requirements... 3 1. Operating system:... 3 2. Hardware:... 3 Minimum Graphics card
More informationAn introduction to 3D draughting & solid modelling using AutoCAD
An introduction to 3D draughting & solid modelling using AutoCAD Faculty of Technology University of Plymouth Drake Circus Plymouth PL4 8AA These notes are to be used in conjunction with the AutoCAD software
More informationSMART Board Interactive Whiteboard Basics Tip Sheet for ABP Faculty
SMART Board Interactive Whiteboard Basics Tip Sheet for ABP Faculty Introduction The SMART Board interactive whiteboard is touch sensitive and operates as part of a system that includes a computer and
More informationTime Stamp. Instruction Booklet
Time Stamp Instruction Booklet Time Stamp Introductions Time stamp is a useful solution for backing up and restoring system, it backs up the entire computer system to the Backup Zone. Time Stamp is used
More informationCreate a new file/canvas to work with by going to the file menu and selecting new.
GIMP: Gif Animation Animating images to create a cartoon-like effect can be performed in GIMP. The GIMP program will only animate.gi f files, so the animation will appear more like a cartoon than like
More informationLayouts, Plotting, Printing
Layouts, Plotting, Printing Sacramento City College Engineering Design Technology Layouts, Plotting, Printing 1 Objectives Print and plot a drawing. Set up layouts using title blocks and viewports. Create
More informationBLOCKS and AutoCAD DesignCenter
BLOCKS and AutoCAD DesignCenter Chapter Objectives After completing this chapter you should: 1. understand the concept of creating and inserting symbols in AutoCAD drawings; 2. be able to use the Block
More informationInterior Design Tutorial
Chapter 4: Interior Design Tutorial In the Interior Design Tutorial, we ll pick up where we left off in the House Design Tutorial. The shell and basic structure of our plan is complete, but a lot of interior
More informationNorthClark Computing, Inc. Bill of Material and Parts Master Maintenance. Administrator s Guide
ERP Consulting Web Development Custom Programming Solutions Desktop & Web Applications for Manfact NorthClark Computing, Inc. Bill of Material and Parts Master Maintenance Administrator s Guide Web and
More informationCreating Figure Ground Maps in ArcMap 10.x: Basic procedures to download, open, manipulate and print spatial data
Creating Figure Ground Maps in ArcMap 10.x: Basic procedures to download, open, manipulate and print spatial data These procedures outline: A. Retrieving Property Data B. Uncompressing the Downloaded Files
More informationCreate a Poster Using Publisher
Contents 1. Introduction 1. Starting Publisher 2. Create a Poster Template 5. Aligning your images and text 7. Apply a background 12. Add text to your poster 14. Add pictures to your poster 17. Add graphs
More informationSMART Board Interactive Whiteboard Setup with USB Cable
SMART Board Interactive Whiteboard Setup with USB Cable The instructions below are for the SMART Board interactive whiteboard 500 series and apply to both desktop and laptop computers. Ready Light USB
More informationUsing BitLocker to encrypt a Windows 8 device
Using BitLocker to encrypt a Windows 8 device 1. Before BitLocker can be used to encrypt the portable device, the Trusted Platform Module must be turned on via the BIOS. Boot the device and press F2, F10,
More informationPhotocopying and scanning
Photocopying and scanning Logging in at the copier Scan your card using the Barcode Scanner at the copier Press in the PIN field Enter your PIN, and then press OK. 1 Photocopying 1. Position your document
More informationSolidWorks. SolidWorks Teacher Guide. and Student Courseware
SolidWorks SolidWorks Teacher Guide and Student Courseware SolidWorks Corporation Outside the U.S.: +1-978-371-5011 300 Baker Avenue Fax: +1-978-371-7303 Concord, Massachusetts 01742 USA Email: info@solidworks.com
More informationManual. OIRE Escuela de Profesiones de la Salud. Power Point 2007
Power Point 2007 Manual OIRE Escuela de Profesiones de la Salud Power Point 2007 2008 The New Power Point Interface PowerPoint is currently the most common software used for making visual aids for presentations.
More informationUSB Flash Drive. The New Age of Data Storage. 2008 Future. 1990s - 2007
The New Age of Data Storage 1990s - 2007 2008 Future The New Age of Data Storage This presentation is for the Faculty and Students of Kingsborough Community College. The Office of Information Technology
More informationAutoDWG DWGSee DWG Viewer. DWGSee User Guide
DWGSee User Guide DWGSee is comprehensive software for viewing, printing, marking and sharing DWG files. It is fast, powerful and easy-to-use for every expert and beginners. Starting DWGSee After you install
More informationUniversity of Minnesota Financial Document Scanning Guide for ImageNow 6.2
University of Minnesota Financial Document Scanning Guide for ImageNow 6.2 INTRODUCTION... 2 LAUNCHING IMAGENOW AND LOGGING IN... 2 IMAGENOW TOOLBAR... 3 SCANNING DOCUMENTS INTO IMAGENOW... 3 PREPARATION...
More information6. If you want to enter specific formats, click the Format Tab to auto format the information that is entered into the field.
Adobe Acrobat Professional X Part 3 - Creating Fillable Forms Preparing the Form Create the form in Word, including underlines, images and any other text you would like showing on the form. Convert the
More informationHow to borrow and download an ebook using Bolinda (PC)
How to borrow and download an ebook using Bolinda (PC) Before you begin, you will need: Your library card number and PIN An email address Note: If you have already installed Adobe Digital Editions on your
More informationA Guide to Getting Started with the AmeriCorps VISTA Applicant Tracking Tool
A Guide to Getting Started with the AmeriCorps VISTA Applicant Tracking Tool The AmeriCorps VISTA Applicant Tracking Tool will help you stay organized, monitor all the necessary steps, and record applicant
More informationWatch Your Garden Grow
Watch Your Garden Grow The Brinno GardenWatchCam is a low cost, light weight, weather resistant, battery operated time-lapse camera that captures the entire lifecycle of any garden season by taking photos
More informationAccount Access User Guide
Account Access User Guide Available within AgriPoint How to manage your accounts online, anytime, anywhere. Rev. 10/12/2015 This guide is designed to familiarize you with the features and options available
More informationMaking a Web Page with Microsoft Publisher 2003
Making a Web Page with Microsoft Publisher 2003 The first thing to consider when making a Web page or a Web site is the architecture of the site. How many pages will you have and how will they link to
More informationHITT101 H-ITT Audience Response System 101
HITT101 H-ITT Audience Response System 101 Hardware Setup First Time Hardware Setup - WARNING this does take a few minutes Please note that the first time you insert the USB cable from the H-ITT receiver
More informationCANON FAX L360 SOFTWARE MANUAL
CANON FAX L360 SOFTWARE MANUAL Before You Begin the Installation: a Checklist 2 To ensure a smooth and successful installation, take some time before you begin to plan and prepare for the installation
More informationAdobe Illustrator CS5 Part 1: Introduction to Illustrator
CALIFORNIA STATE UNIVERSITY, LOS ANGELES INFORMATION TECHNOLOGY SERVICES Adobe Illustrator CS5 Part 1: Introduction to Illustrator Summer 2011, Version 1.0 Table of Contents Introduction...2 Downloading
More informationOpening the FTD Document Center. Double-click the FTD Document Center icon on your Windows desktop.
23 The allows you to create templates for email messages that you will send from FTD Mercury. You can create several different delivery confirmation templates, as well as email cover letters that can be
More informationQuick Start Using DASYLab with your Measurement Computing USB device
Quick Start Using DASYLab with your Measurement Computing USB device Thank you for purchasing a USB data acquisition device from Measurement Computing Corporation (MCC). This Quick Start document contains
More informationEASE Scan Tool Customers. SECTION I - Installation
Please Install Your EASE Scan Tool DVD Before Installing Any Other Software That Came With Your Package. SECTION I - Installation ATTENTION: Do NOT connect an EASE Vehicle Interface Device to your Computer
More informationPodium View TM 2.0 Visual Presenter Image Software User Manual - English (WINDOWS)
Podium View TM 2.0 Visual Presenter Image Software User Manual - English (WINDOWS) Table of Contents 1. Introduction... 2 2. System Requirements... 2 3. Installing Podium View... 3 4. Connection to the
More informationEPSON Stylus COLOR 740. USB Software Installation Guide (Windows 98/iMac ) USB Setup Guide (imac)
EPSON Stylus COLOR 740 TM USB Software Installation Guide (Windows 98/iMac ) USB Setup Guide (imac) This guide includes USB setup instructions for your imac computer, as well as software installation instructions
More informationUsing the Waterjet. Step One: Export your CAD drawing as a Release 12 DXF file. Step Two: Import your DXF file in FlowPATH
Using the Waterjet Digital Media Tutorial Written By: John Eberhart The waterjet shoots water out of a nozzle at 3 times the speed of sound. This combined with abrasive (garnet) allows the waterjet to
More informationUsing Clicker 5. Hide/View Explorer. Go to the Home Grid. Create Grids. Folders, Grids, and Files. Navigation Tools
Using Clicker 5 Mouse and Keyboard Functions in Clicker Grids A two-button mouse may be used to control access various features of the Clicker program. This table shows the basic uses of mouse clicks with
More informationSolidWorks: Mirror, Revolve, and. Introduction to Robotics
SolidWorks: Mirror, Revolve, and Circular Pattern Introduction to Robotics Let s Review At this point we have learned the following: Extrude Boss/Base Extruded Cut Adding Relations and Dimensions Linear
More informationRaising the Roof Creating Roofs in Revit David Cohn
David Cohn AB322-1 Roofs are one of the most complex architectural elements to model, but with Revit you can create just about any type of roof. This class will explore the best methods for creating various
More informationEmbroidery Fonts Plus ( EFP ) Tutorial Guide Version 1.0505
Embroidery Fonts Plus ( EFP ) Tutorial Guide Version 1.0505 1 Contents Chapter 1 System Requirements.................. 3 Chapter 2 Quick Start Installation.................. 4 System Requirements................
More informationTurboCAD Architectural
TurboCAD Architectural Version 15 Getting Started Guide IMSI/Design LLC, US 100 Rowland Blvd. Novato. CA 94945, USA Tel: +1-415-878-4000 Fax: +1-415-897-2544 Web Site www.imsisoft.com www.turbocad.com
More informationMrSID Viewer 2.0 for Windows 95/NT4.0
MrSID Viewer 2.0 for Windows 95/NT4.0 What is MrSID? Introducing MrSID MrSID image compression and decompression software offers users high-quality image-compression capabilities, along with the ability
More informationGuide to Using AMS 4.0 Marking Software
Guide to Using AMS 4.0 Marking Software Guide to Using AMS 4.0 Marking Software Contents System Requirements...2 Software Installation...2 Selecting the Output Device and Changing Settings...2 Definitions...
More informationWelcome to Bridgit @ CSU The Software Used To Data Conference.
Welcome to Bridgit @ CSU The Software Used To Data Conference. Overview SMART Bridgit software is a client/server application that lets you share programs and information with anyone, anywhere in the world.
More informationKitchen and Bath Design Tutorial
Chapter 5: Kitchen and Bath Design Tutorial This tutorial continues where the Materials Tutorial left off. You should save this tutorial using a new name to archive your previous work. The tools and techniques
More informationTable of Contents. Part I Welcome. Part II Introduction. Part III Getting Started. Part IV The User Interface. Part V Quick Start Tutorials
Contents I Table of Contents Part I Welcome 5 Part II Introduction 5 1 Overview... 5 2 Product... Levels 5 3 Technical... Support 6 4 Copyright... 7 Part III Getting Started 7 1 Installation... 7 2 Register...
More informationRoof Tutorial. Chapter 3:
Chapter 3: Roof Tutorial The majority of Roof Tutorial describes some common roof styles that can be created using settings in the Wall Specification dialog and can be completed independent of the other
More informationFrequently Asked Questions Overview:
Frequently Asked Questions Overview: Do I have to register the software? Product registration is not required to preview the software but is recommended. Registration of the product will allow us to provide
More informationMicro Cam Software. User Manual V1.3
Micro Cam Software User Manual V1.3 CONTENT CHAPTER 1: MICRO CAM SOFTWARE INSTALLATION AND CONNECTION... - 1-1.1 SOFTWARE MICRO CAM INSTALLATION... - 1-1.2 WIRED DEVICE CONNECTION... - 4-1.3 SOFTWARE OPERATION
More informationEnhanced Imaging Options for Client Profiles for Windows
C ase Manag e m e n t by C l i e n t P rofiles Enhanced Imaging Options for Client Profiles for Windows T E C H N O L O G Y F O R T H E B U S I N E S S O F L A W Table of Contents 2 Table of Contents Scanning
More informationZoomText 10.1 for Windows 8 Quick Reference Guide Addendum
ZoomText 10.1 for Windows 8 Quick Reference Guide Addendum This addendum to the ZoomText 10 Quick Reference Guide covers the new features and other changes specific to ZoomText 10.1 for Windows 8. For
More informationMac OS X 10 Using the Keyboard Viewer and Character Palette
Mac OS X 10 Using the Keyboard Viewer and Character Palette Use Keyboard Viewer to see the layout of characters on your keyboard for your chosen language. For example, if the U.S. is selected in the Input
More informationVirtual Office Remote Installation Guide
Virtual Office Remote Installation Guide Table of Contents VIRTUAL OFFICE REMOTE INSTALLATION GUIDE... 3 UNIVERSAL PRINTER CONFIGURATION INSTRUCTIONS... 12 CHANGING DEFAULT PRINTERS ON LOCAL SYSTEM...
More informationLayout Tutorial. Chapter 10: Getting Started
Chapter 10: Layout Tutorial In this tutorial we will create a layout template, send a few views to a layout page, then save this document in PDF format. In this tutorial you will learn about: Creating
More informationGetting Started Guide. Trimble Accubid Enterprise Software
Getting Started Guide Trimble Accubid Enterprise Software Revision A August 2013 F Toronto Office Trimble Canada Ltd. 7725 Jane Street Concord, Ontario L4K 1X4 Copyright and Trademarks 2005-2013 Trimble
More informationUsing Remote Web Workplace Version 1.01
Using Remote Web Workplace Version 1.01 Remote web workplace allows you to access your Windows XP desktop through Small Business Server 2003 from a web browser. 1. Connect to the Internet in your remote
More informationYouthQuest Quick Key FOB Project
YouthQuest Quick Key FOB Project This project is designed to demonstrate how to use the 3D design application, Moment of inspiration, to create a custom key fob for printing on the Cube3 3D printer. Downloading
More informationAddendum Advanced POS Printer Drivers
Addendum Advanced POS Printer Drivers Overview With the introduction of version 4.0, The General Store now supports the use of advanced, manufacturer s printer drivers for certain point of sale printers.
More informationOUTLOOK 2013 - GETTING STARTED
OUTLOOK 2013 - GETTING STARTED Information Technology September 1, 2014 1 GETTING STARTED IN OUTLOOK 2013 Backstage View Ribbon Navigation Pane View Pane Navigation Bar Reading Pane 2 Backstage View contains
More informationFDOT Plans Production Tools
FDOT State Kit for AutoCAD Civil 3D Mike Racca CADD APPLICATIONS SUPPORT Florida Department of Transportation (ECSO) Email: Mike.Racca@dot.state.fl.us Phone: 850-245-1631 GENERAL Civil 3D Plan Production
More informationMicrosoft Office Access 2007 Basics
Access(ing) A Database Project PRESENTED BY THE TECHNOLOGY TRAINERS OF THE MONROE COUNTY LIBRARY SYSTEM EMAIL: TRAININGLAB@MONROE.LIB.MI.US MONROE COUNTY LIBRARY SYSTEM 734-241-5770 1 840 SOUTH ROESSLER
More information