PotashCorp New Brunswick Division Picadilly Potash Project ETAP SIMULATION Prepared by: Carlos Reinel Senior Engineer R&D Department Power Survey International Approved by: Pierre Archambault, PEng. VP Engineering Power Survey International Inc. 16 September 2009 Page 1 of 15
TABLE OF CONTENTS 1. GENERAL 1.1 Purpose of this Study 1.2 Data Available 1.3 Assumptions 1.4 Summary 2. RESULTS 2.1 ETAP Single Line Diagram 2.2 Current and Voltage Harmonics at PCC 2.3 Filter Currents 2.4 Capacitor Voltages 2.5 Conclusions 3. APPENDIX 3.1 IEEE Guidelines Page 2 of 15
1. GENERAL 1.1 Purpose of this Study The purpose of this study is to check the harmonic distortion at the Point of Common Coupling in compliance with IEEE 519 guidelines. This study is based on available data as indicated in the next section. The system simulation has been performed using ETAP Software Version 5.5.6 1.2 Data Available Following files and documents were available: Penobsquis VFD MCCs.pdf Motor List Picadilly VFD MCCs.pdf Motor List Load Distribution for Cap Banks Pic and Pen.xls Excel Spreadsheet PSMV1003-1.dwg Drawing # 130-20-10000 PSMV1003-1.dwg Drawing # 130-20-10001 PSMV1003-2.dwg Drawing # 130-20-10002 320-20-41201%20R1_6142-1.pdf System Layout Page 3 of 15
Filter Data BANKS 1,2 Step1 Nominal 2000 KVAR Effective 2011 KVAR @ 13.8 KV C 26.74 µf / ph C 6x500.06 KVAR @ 9.96 KV XL 4.490 Ohms N 4.70 h Step2 Nominal 2000 KVAR Effective 1968 KVAR @ 13.8 KV C 27.86 µf C 6x500.73 KVAR @ 9.96 KV XL 2.199 Ohms N 6.58 h BANKS 3, 4, 5 Step1 Nominal 2500 KVAR Effective 2632 KVAR @ 13.8 KV C 35.00 µf C 6x600.45 KVAR @ 9.54 KV XL 3.431 Ohms N 4.70 h Step2 Nominal 2500 KVAR Effective 2572 KVAR @ 13.8 KV C 35.00 µf C 6x600.39 KVAR @ 9.54 KV XL 1.751 Ohms N 6.58 h Step3 Nominal 2500 KVAR Effective 2535 KVAR @ 13.8 KV C 34.98 µf C 6x600.07 KVAR @ 9.54 KV XL 0.706 Ohms N 10.34 h Serving you since 1948 Page 4 of 15
1.3 Assumptions Following the data specified above and having installed the one line diagram on ETAP, the following assumptions were made: Utility: Isc = 4.18 ka sym. @ 138 kv 1,000 MVA Tie-breakers Open at all voltage levels Feeder 1007A Open Harmonic Injections As per Amec Specifications #156930-E-SP-16331, Section 2.2 Sources of Harmonic Currents, pages 14-16 Page 5 of 15
1.4 Summary Harmonic Currents - IEEE519 Compliance As per Section 2.2 of this report, a compliance with IEEE 519 guidelines was found for the simulated system at the PCC point. The only remark due is that the mine hoist drives do not show any low end harmonic injection for n < 35, but adding limited harmonics (less than 5%) below that frequency does not change the results. Page 6 of 15
2. RESULTS 2.1 ETAP Single Line Diagram Page 7 of 15
Page 8 of 15
2.2 Current and Voltage Harmonics at PCC Serving you since 1948 The following table shows the harmonic currents at the primary side of the main 40 MVA 138/13.8 kv transformers T303 and T304: T303 T304 T303 T304 [%] [%] Amp Amp 1 IEEE 100 100 115.06 96.20 5 4 0.2750 0.3243 0.32 0.31 7 4 0.0347 0.0532 0.04 0.05 11 2 0.0105 0.0211 0.01 0.02 13 2 0.0122 0.0271 0.01 0.03 17 1.5 0.0088 0.0188 0.01 0.02 19 1.5 0.0083 0.0169 0.01 0.02 23 0.6 0.0055 0.0100 0.01 0.01 25 0.6 0.0039 0.0073 0.00 0.01 29 0.6 0.0040 0.0071 0.00 0.01 31 0.6 0.0035 0.0066 0.00 0.01 35 0.3 0.0731 0.1439 0.08 0.14 37 0.3 0.0469 0.0906 0.05 0.09 41 0.3 0.0017 0.0024 0.00 0.00 43 0.3 0.0018 0.0024 0.00 0.00 47 0.3 0.0588 0.1042 0.07 0.10 49 0.3 0.0467 0.0811 0.05 0.08 59 0.3 0.0172 0.0282 0.02 0.03 61 0.3 0.0105 0.0169 0.01 0.02 71 0.3 0.0037 0.0056 0.00 0.01 73 0.3 0.0075 0.0113 0.01 0.01 THD 5 0.3016 0.3970 The above table show comfortable compliance with IEEE limits for Isc/IL < 20 (most demanding condition, worst case possible). Page 9 of 15
The following table shows the voltage harmonics at the main 13.8 kv busses SGR303 and SGR304 (40 MVA main transformers, secondary side): SGR303 SGR304 SGR303 SGR304 [%] [%] Volts Volts 1 100 100 13800 13800 5 0.1511 0.1501 20.85 20.71 7 0.0291 0.0336 4.02 4.64 11 0.0142 0.0196 1.96 2.71 13 0.0209 0.0300 2.89 4.14 17 0.0193 0.0274 2.67 3.78 19 0.0199 0.0277 2.74 3.82 23 0.0151 0.0201 2.08 2.77 25 0.0116 0.0158 1.61 2.17 29 0.0134 0.0179 1.84 2.47 31 0.0126 0.0177 1.74 2.44 35 0.3161 0.4416 43.63 60.94 37 0.2114 0.2945 29.17 40.64 41 0.0073 0.0088 1.01 1.22 43 0.0076 0.0091 1.05 1.26 47 0.3169 0.4364 43.73 60.22 49 0.2590 0.3553 35.74 49.03 59 0.1091 0.1503 15.05 20.74 61 0.0678 0.0934 9.36 12.89 71 0.0267 0.0367 3.68 5.06 73 0.0551 0.0757 7.60 10.44 THD 0.60 0.82 Voltage THD values are well below IEEE limit of 3% for Special Applications (worst case). Page 10 of 15
2.3 Filter Currents The following tables show the filter currents for the different filter steps: F1.STP1 F1.STP2 F1.STP1 F1.STP2 F3.STP1 F3.STP2 F3.STP3 F3.STP1 F3.STP2 F3.STP3 [%] [%] Amps Amps [%] [%] [%] Amps Amps Amps 1 100 100 83.13 81.37 100 100 100 109.81 107.32 105.75 5 5.4861 1.7564 4.56 1.43 4.9544 1.7440 0.9789 5.44 1.87 1.04 7 0.1866 1.7576 0.16 1.43 0.1590 1.2774 0.3724 0.17 1.37 0.39 11 0.0466 0.1189 0.04 0.10 0.0332 0.0841 0.8508 0.04 0.09 0.90 13 0.0567 0.1328 0.05 0.11 0.0388 0.0904 0.4394 0.04 0.10 0.46 17 0.0372 0.0811 0.03 0.07 0.0256 0.0556 0.1852 0.03 0.06 0.20 19 0.0331 0.0708 0.03 0.06 0.0231 0.0493 0.1527 0.03 0.05 0.16 23 0.0194 0.0407 0.02 0.03 0.0141 0.0294 0.0841 0.02 0.03 0.09 25 0.0139 0.0290 0.01 0.02 0.0099 0.0205 0.0572 0.01 0.02 0.06 29 0.0135 0.0278 0.01 0.02 0.0096 0.0197 0.0533 0.01 0.02 0.06 31 0.0124 0.0255 0.01 0.02 0.0084 0.0172 0.0460 0.01 0.02 0.05 35 0.2743 0.5597 0.23 0.46 0.1834 0.3735 0.9829 0.20 0.40 1.04 37 0.1727 0.3517 0.14 0.29 0.1150 0.2338 0.6117 0.13 0.25 0.65 41 0.0046 0.0094 0.00 0.01 0.0035 0.0072 0.0186 0.00 0.01 0.02 43 0.0046 0.0093 0.00 0.01 0.0035 0.0071 0.0182 0.00 0.01 0.02 47 0.2002 0.4053 0.17 0.33 0.1302 0.2632 0.6757 0.14 0.28 0.71 49 0.1562 0.3160 0.13 0.26 0.1012 0.2044 0.5235 0.11 0.22 0.55 59 0.0547 0.1104 0.05 0.09 0.0339 0.0682 0.1733 0.04 0.07 0.18 61 0.0329 0.0663 0.03 0.05 0.0202 0.0406 0.1031 0.02 0.04 0.11 71 0.0111 0.0223 0.01 0.02 0.0065 0.0131 0.0331 0.01 0.01 0.03 73 0.0222 0.0447 0.02 0.04 0.0129 0.0260 0.0657 0.01 0.03 0.07 THD % 5.51 2.63 4.97 2.24 2.05 IRMS A 83.26 81.40 109.95 107.35 105.77 Where: F1.STP1 is Filter 1 Step1, etc. Note: Only Filters 1 and 3 are listed above. The fundamental and harmonic currents of Filter 2 are almost identical as for Filter 1. The fundamental and harmonic currents of Filters 4 and 5 are almost identical as for Filter 3. This is because the currents depend mainly on the filter components (Filter 1 and 2 are identical and Filters 3 to 5 are identical). The bus impedances are also basically identical on each of both filter types, as no cabling has been considered in this simulation and the transformers for feeding each filter type are identical. Loads are all different though, but they do not affect the Z bus /Z filter ratio calculation by any considerable value. This fact was double-checked on the ETAP model. The table above shows there will be no major harmonic over-loading of the filter reactors due to the extremely limited harmonic currents. Page 11 of 15
2.4 Capacitor Voltages The following tables show the filter voltages for the different filter steps: F1.STP1 F1.STP2 F3.STP1 F3.STP2 F3.STP3 Volts Volts Volts Volts Volts 1 13,800 13,800 13,800 13,800 13,800 5 94.42 32.44 101.23 34.83 19.28 7 2.33 18.32 2.36 18.54 5.33 11 0.27 0.67 0.32 0.79 7.90 13 0.31 0.71 0.32 0.72 3.45 17 0.16 0.35 0.16 0.35 1.15 19 0.13 0.28 0.13 0.28 0.84 23 0.07 0.13 0.07 0.13 0.38 25 0.04 0.09 0.04 0.09 0.24 29 0.04 0.07 0.04 0.07 0.19 31 0.03 0.06 0.03 0.06 0.17 35 0.75 1.49 0.75 1.49 3.87 37 0.44 0.88 0.44 0.88 2.28 41 0.01 0.02 0.01 0.02 0.04 43 0.01 0.02 0.01 0.02 0.04 47 0.39 0.78 0.40 0.79 1.99 49 0.29 0.58 0.30 0.58 1.47 59 0.08 0.16 0.08 0.16 0.41 61 0.05 0.09 0.05 0.09 0.24 71 0.01 0.03 0.01 0.03 0.07 73 0.03 0.05 0.03 0.05 0.13 SUM 13,900 13,857 13,907 13,860 13,849 Where: F1.STP1 is Filter 1 Step1, etc. Note: Only Filters 1 and 3 are listed above. Same is valid as for the harmonic currents. Page 12 of 15
2.5 Conclusions As per Section 2.2 of this report, a compliance with IEEE 519 guidelines was found for the simulated system at the PCC point and there will be no major harmonic over-loading of the filter reactors due to the extremely limited harmonic currents of the hoist drives. Voltage harmonics will also not represent any major problem for the capacitors. Some harmonics at the low frequency end could result higher than the predicted values from this model, as some 5 th, 7 th and 11 th harmonics will most likely spill over from the large hoist drives anyhow. A hoist duty cycle would help to improve the accuracy of the predicted harmonic levels considering that peak torque requirements of mine hoist drives for about 10 to 20 seconds every 2 minutes are normally about 200% or even higher. Page 13 of 15
3. APPENDIX 3.1 IEEE Guidelines IEEE 519 Guidelines for Current Distortion Page 14 of 15
IEEE 519 Guidelines for Voltage Distortion Serving you since 1948 Page 15 of 15