Insulated Panels CI/SfB (4-) Rh2 September 2008 INSULATED WALL SYSTEMS Longspan Architectural Frame to Frame Insulated Panel System Approved to LPS 1181 Certificate No. 186a & 260a
Longspan is a frame to frame insulated wall panel system which can eliminate secondary steel work The paper we have printed on is from 80% postconsumer waste and the remaining 20% pulp is TCF (Totally Chlorine Free). This fibre is FSC certified (see fsc.org for details). In recognition, the range has been awarded both the NAPM and Eugropa recycled marks, two of the most prestigious and recognisable recycled certificates available. The ink we have used is vegetable based, allowing the document to be recycled. Sustainable Forest Recyclable Vegetable Based 2
Contents Contents Introduction 5 Product Data 6 Construction Details 10 3
4 The Longspan system is a high performance construction solution providing external architectural aesthetics combined with faster on-site installation
Introduction The KS1000 LS Longspan System is a cost effective architectural wall system which provides quicker project completion, simpler installation and guaranteed performance. KS1000 LS Longspan wall panels can span up to 8.2 metres from support to support, providing enhanced aesthetics and reducing the need for secondary steelwork. Performance Advantages Property & Business Protection - Loss Prevention Certification Board (LPCB) LPS 1181 certified insurer approved systems deliver certainty of performance and insurability. Complies with HSA/HSE and CDM safety requirements. Fully complies with Part L2 (England & Wales) Building Regulations and Section 6 (Scotland) Technical Handbooks. Lifetime insulation continuity, thermal performance and airtightness (5m 3 /hr/m 2 ) certainty. Frame to frame spanning capability of up to 8.2 metres. Available in cover widths of 600, 900 and 1000mm. Standard Architectural Panel Six external architectural profiles available Simple integration with doors, windows, glazing, louvres and traditional construction materials. Suitable for horizontal or vertical application. Accelerated build speed through pre-engineered, single component, single-fix installation, that can reduce site times by up to 50%. Introduction Environmentally sustainable system - zero ODP and non-deleterious. Guaranteed for up to 25 years for thermal and structural performance through TOTAL Guarantee. Quality approved to ISO 9001: 2000. s manufacturing plants are ISO 14001 (Environmentally) and ISO 18001 (Health & Safety) accredited. Approved to LPS 1181 Certificate No. 186a & 260a KS600/900/1000 LS Longspan Panel 5
Product Data Application KS1000 LS Longspan is a frame to frame long spanning, secret fixed system which can be laid horizontally and vertically. It is suitable for all building applications except where there are low temperature controlled environments. Product Reference KS600/900/1000 Application Description KS1000 LS Longspan wall panel with Loss Prevention Certification Board (LPCB) approval for wall applications. KS600/900/1000 LS 600/900/1000mm cover width Core thickness A - Core thickness (mm) 80 100 120 140 Weight (kg/m 2 ) 0.63/0.63 steel 15.4 16.2 17.0 17.8 Product Tolerances Cut to Length (mm) -5 +5 Cover Width (mm) -2 +2 Thickness (mm) -2 +2 End Square (mm) -3 +3 Flatness per metre (mm) -2 +2 Profiles Available The external weather sheet is available in six profiles: MR (Micro-Rib) EB (Euro-Box) MM (Mini-Micro) WV (Wave) CX (Convex) FL/FL-S (Flat) Available Lengths Standard lengths of 1.8 to 12.0 metres, 12.1 to 16 metre panels can be supplied but are subject to a transport surcharge. Panels less than 1.8m long can be supplied and are subject to an extra cost. Panel length Material Steel Substrate Standard external sheet thickness 0.63mm, standard internal sheet thickness 0.63mm. Other thicknesses can be supplied to special order. Coatings External Weather Sheet XL Forté : 200 micron thick high performance coating applied to the weatherside of the panel. Designed to achieve high levels of durability and colour stability and is highly resistant to damage in transit and on-site. Spectrum - polyurethane semi-gloss coating. Colorcoat Prisma - 50 micron thick coating. 16 metallic colours. HPS200 Ultra - Nominal 200 micron thick high performance coating. Reverse side of sheet coated with grey polyester coating. The steel is available in either plain or stucco embossed finish. Coatings Internal Liner Sheet Bright White Polyester: Coating developed for use as the internal lining of insulated panels. Standard colour is bright white with an easy clean surface. Aquasafe 200: 200 micron thick coating used in areas where there is high internal humidity, or a corrosive environment. Cleansafe: a chemically inert polymer film bonded to steel substrate for cladding of cold stores, food processing buildings and other hygiene applications. Reverse side of sheet coated with a light grey polyester coating. The sheet is available in either plain or stucco embossed finish. These panels cannot be end lapped. 6
Insulation Core The core of KS1000 LS Longspan is a, closed cell PIR insulation which is non-deleterious with zero Ozone Depletion Potential (zero ODP). Seals Factory Applied Side Joint Seal All side joints have a factory applied seal fitted into the groove to automatically seal the joint between panels. Performance Thermal Insulation Panel Thickness (mm) U-value W/m 2 K 80 0.30 100 0.23 120 0.17 140 0.15 U-value - Thermal transmittance W/m 2 K Biological KS1000 LS Longspan panels are resistant to attack from mould, fungi, mildew and vermin. No urea formaldehyde is used in the manufacture of the panels. Fire Steel inner and outer facings have a Class 1 surface spread of flame to BS476 Part 7: 1987, and are Class 0 as defined by the Building Regulations. KS1000 LS Longspan is approved by the Loss Prevention Certification Board (LPCB) to LPS1181. KS1000 LS Longspan panels have a core which has been specially formulated to provide the following benefits: Stable protective char No flash over No flame spread No flame propagation Acoustics All KS1000 LS Longspan panels have a single figure weighted sound reduction Rw = 25dB. Sound Reduction Index (SRI) Frequency (Hz) SRI (db) 125 20.1 250 21.1 500 24.6 1000 24.9 2000 29.6 4000 38.0 Quality insulated panels are manufactured from the highest quality materials, using state of the art production equipment to rigorous quality control standards, approved to ISO 9001: 2000. manufacturing plants are ISO 14001 (Environmentally) and ISO 18001 (Health & Safety) accredited. Guarantees insulated panels are available with the TOTAL Guarantee offering 25 years thermal and structural performance guarantee. Packing Standard Packing KS1000 LS Longspan panels are stacked face up and require turning over during unpacking / erection. Removable hot melt adhesive is laid between each panel. The top, bottom, sides and each end are protected with polystyrene and timber packing and the entire pack is wrapped in polythene. The number of panels in each pack depends on the panel thickness, as shown in the table below. Typical pack height is 1100mm. Panel Core Thickness 80 100 120 140 No. panel/pack (max.) 11 10 7 7 Sea Freight Fully timber crated packs are available on projects requiring delivery by sea freight shipping, at additional cost. Alternatively, steel containers can be used. Special loading charges apply. Delivery All deliveries (unless indicated otherwise) are road transport to project site. Off loading is the responsibility of the cladding contractor or installer. Typical Spans Product Reference Typical Single Span (m) KS1000 LS 80 5.0 KS1000 LS 100 6.0 KS1000 LS 120 7.0 KS1000 LS 140 8.0 Notes: These typical spans are based on a design wind pressure and suction of 0.9kN/m 2, for guidance only. Please check exact design wind loads for building (obtained from the project engineer) with the load/span table on page 8. Product Data 7
Structural Unfactored Load/Span Table (use calculated design windload values unfactored) Span Core Load Uniformly Distributed Loads (kn/m 2 ) Condition Thickness Type Span L in metres (mm) 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 Single Span 80 Pressure 3.12 2.31 1.73 1.34 1.04 0.81 - - - - - Outer sheet Suction 2.75 1.98 1.44 1.08 0.81 0.61 - - - - - 0.63mm steel 100 Pressure 3.57 3.05 2.41 1.89 1.51 1.20 0.97 0.73 - - - Inner sheet Suction 3.55 2.78 2.10 1.61 1.26 0.98 0.77 0.61 - - - 0.63mm steel 120 Pressure 3.75 3.21 2.80 2.45 1.98 1.61 1.32 1.10 0.92 - - L Suction 3.75 3.21 2.68 2.12 1.72 1.36 1.10 0.88 0.73 - - 140 Pressure 3.75 3.21 2.80 2.45 2.24 2.00 1.66 1.39 1.18 0.99 0.85 Suction 3.75 3.21 2.80 2.34 1.90 1.56 1.31 1.12 0.96 0.81 0.68 Notes: 1. Values have been calculated using the limit state method described in the European recommendations for the design of sandwich panels. (ECCS document No.115 2001). Taking imposed loads, temperature and creep into account. 2. For each value individual and combined load cases with appropriate load factors and temperatures have been considered. These are detailed under Structural Performance in the Building Design Section of the Design & Construction Guide. 3. The table is for dark coloured panels. 4. The following deflection limits have been used: Pressure loading L /100 Suction loading L /100 5. For Intermediate values linear interpolation may be used. 6. The actual wind suction load resisted by the panel is dependant on the number of fasteners used. The fastener calculation should be carried out in accordance with the appropriate standard. For further advice please contact envirocare Technical Services. 7. The allowable steelwork tolerance between bearing planes of adjacent vertical columns is 10mm to NSSS (National Structural Steelwork Specification). 8. Load span tables for the panel specifications not shown are available from the envirocare Technical Services. 8
9 Product Data
Construction Details Vertical Joint Details Option A Detail Panel fasteners at joint only. Number dependent upon design wind suction loadings. 40mm Air seal EPDM bubble gasket 95 x 10mm, Ref: VJ2 Supplied in 25m rolls PIR board insulation with fire rated canister insulation to fill any gaps if required to maintain continuity of insulation AWP joint filler and gun-grade sealant Air seal gun-grade sealant to male joint 4mm diameter butyl rubber sealant (site applied) Option A top hat (roll formed) 30mm deep with 100mm sealed butt straps. Supplied in max. 6000mm lengths 30mm KS1000 LS Longspan TM horizontally laid Snap on cover flashing. Maximum 6000mm lengths 10
Option B Detail Panel fasteners at joint only. Number dependent upon design wind suction loadings 40mm Air seal EPDM bubble gasket 95mm x 10mm, Ref: VJ2 Supplied in 25m rolls PIR board insulation with fire rated canister insulation to fill any gaps if required to maintain continuity of insulation AWP joint filler and gun-grade sealant Air seal gun-grade sealant to male joint 4mm diameter butyl rubber sealant (site applied) Option B top hat (roll formed) 30mm deep with 100mm sealed butt straps. Supplied in max. 6000mm lengths 30mm KS1000 LS Longspan TM horizontally laid Construction Details 11
Vertical Joint Details Option C Detail 10mm Air seal EPDM bubble gasket 95mm x 10mm, Ref: VJ2 Supplied in 25m rolls Panel fasteners at joint only. Number dependent upon design wind suction loadings. 25mm 25mm Site applied fire rated canister insulation AWP joint filler and gun-grade sealant Air seal gun-grade sealant to male joint 15mm 4mm diameter butyl rubber sealant (site applied) 80mm KS1000 LS Longspan TM horizontally laid Option C Shadow Line feature flashing with 100mm sealed butt straps. Supplied in max. 6000mm lengths Option D Detail Air seal EPDM bubble gasket 95 x 10mm, Ref: VJ2 Supplied in 25m rolls 50mm Panel fasteners at joint only. Number dependent upon design wind suction loadings PIR board insulation with fire rated canister insulation to fill any gaps if required to maintain continuity of insulation AWP joint filler and gun-grade sealant Air seal gun-grade sealant to male joint EPDM integral fir tree seal. Supplied in 50m rolls 34mm KS1000 LS Longspan TM horizontally laid Option D extruded aluminium top hat section TH30 30mm deep with 100mm sealed butt straps. Supplied in 6000mm lengths extruded aluminium insert section Ref: IN11. Supplied in 6000mm lengths. 12
Option E Detail Panel fasteners at joint only. Number dependent upon design wind suction loadings 50mm Air seal EPDM bubble gasket 95mm x 10mm, Ref: VJ2 Supplied in 25m rolls PIR board insulation with fire rated canister insulation to fill any gaps if required to maintain continuity of insulation AWP joint filler and gun-grade sealant Air seal gun-grade sealant to male joint EPDM integral fir tree seal. Supplied in 50m rolls Option D extruded aluminium top hat section TH30 30mm deep with 100mm sealed butt straps. Supplied in 6000mm lengths. Note: extruded aluminium sections are supplied mill finished as standard or can be specified polyester powder coated to BS or RAL colours 34mm KS1000 LS Longspan TM horizontally laid extruded aluminium insert section Ref: IN23. Supplied in 6000mm lengths Drip Detail 140mm thick panel Column face KS1000 LS Longspan TM horizontally laid Internal closure flashing with 100mm sealed laps Air seal 9mm x 3mm butyl rubber sealant Canister applied insulation Drip flashing Base channel (Ref: LS BC 140) for full length of panel levelled with packers and fixed to floor slab at 500mm maximum centres Air seal continuous bead of gun-grade sealant Construction Details 13
Drip Detail 80mm thick panel Column face KS1000 LS Longspan TM horizontally laid Internal closure flashing with 100mm sealed laps Air seal 9mm x 3mm butyl rubber sealant Base channel (Ref: LS BC 80) for full length of panel levelled with packers and fixed to floor slab at 500mm maximum centres Canister applied insulation Air seal continuous bead of gun-grade sealant Drip flashing 14
Vertical Joint Layout KS1000 LS Longspan TM horizontally laid Top hat support cleats at 500mm max centres using avex rivets Avex rivets 4mm diameter butyl rubber seal Vertical top hat Top hat fixed to top hat support cleats Snap on cover cap Construction Details 15
Insulated Roof, Wall & Façade Systems Roof Systems KS1000 RW Trapezoidal KS1000 SF Secret Fix KS1000 TS Slate & Tile Support KS500/1000 ZIP Kingzip Standing Seam KS1000 LP Lo-Pitch EnergiPanel KS1000 CR Curved Roof Roof Tile KS1000 FC Box Profile Envirodek Polycarb Rooflight Wall & Façade Systems & 1000 Optimo & 1000 MR Micro-Rib & 1000 EB Euro-Box & 1000 FL Flat & 1000 FL-S Stucco & 1000 MM Mini-Micro & 1000 CX Convex & 1000 WV Wave & 1000 LS Longspan KS1000 RW Trapezoidal KS1000 FC Box Profile EnergiPanel Thermatile Thermabrick Thermastone WoodTherm Wall-Lite Ancillaries Gutters, Tophats & Flashings Limited UK: Telephone: +44 (0) 1352 716100 Fax: +44 (0) 1352 710161 Email: info@kingspanpanels.com Ireland: Telephone: +353 (0) 42 96 98500 Fax: +353 (0) 42 96 98572 Email: sales.ire@kingspanpanels.com Details for the following countries; Australia, Belgium, Czech Republic, France, Germany, Hungary, Netherlands, New Zealand, Norway, Poland, Romania, Slovakia & Sweden can be found by visiting our website www.kingspanpanels.com or our group website www.kingspan.com Care has been taken to ensure that the contents of this publication are accurate, but Limited and its subsidiary companies do not accept responsibility for errors or for information that is found to be misleading. Suggestions for, or description of, the end use or application of products or methods of working are for information only and Limited and its subsidiaries accept no liability in respect thereof.