1 Scope of delivery... 02 2 Mounting... 03 2.1 Mounting preparation table of contents 2.2 Mounting on cavity walls / lightweight walls... 04 2.2.1 Wall notch 2.2.2 Angles 2.2.3 Insert the lower case 2.2.4 Adjust the frame 2.2.5 Insert the tablet 2.2.6 Close the cover case 2.3 Mounting on solid walls... 07 2.3.1 Wall notch 2.3.2 Mount the lower case 2.3.3 Insert the tablet 2.3.4 Close the cover case 3 Anti-theft-protection... 09 (only for the products with anti-theft-protection) 1
1. Scope of delivery 1 2 3 4 5 6 1 4x hexagon socket head cap screw M4x8 scope of delivery 2 3 4 5 6 6x stud screw M5x6 2x angle 1x lower case 1x case cover 1x hex-wrench (only for the products with anti-theft-protection) 2
2. Mounting 2.1 Mounting preparation Before installing, please consider the following instructions: 1. Do not install or use TabLines TWE in humid or wet environment. 2. The installation location for the wall mount and cabels has to be deep enough. 3. Select a location with sufficient Wi-Fi signal to make sure that all features of your tablet work correctly. 4. Draw the dimensions on the wall to prepare the notch. The measures/dimensions of the wall cut-out are different, depending on whether you have bought a TWE tablet wall installation for the Samsung Galaxy Tab 4 10.1 or for the Samsung Galaxy Tab 3 10.1. Dimensions for the notch: Samsung Galaxy Tab 4 10.1: 291 x 230 x 15 mm Samsung Galaxy Tab 3 10.1: 219 x 289 x 17 mm Engineering drawings of the TWE models: Fig. 1: TWE for Samsung Galaxy Tab 4 10.1; Tab 3 10.1 3
The TWE wall installation is suitable for cavity walls, lightweight walls and solid walls. If you have a cavity wall/ lightweight wall, please follow the continuing instruction (2.2). If you have a solid wall, skip the step 2.2 and continue with 2.3. 2.2 Mounting on cavity walls/ lightweight walls 2.2.1 Wall notch Select an area of the wall and draw the dimensions on it (leightweight walls). Cut out the selected area. Check the needed depth! Fig. 3: Mark the position 2.2.2 Angles 3 Depending on the wall, TabLines TWE can be used with or without the provided angles. Mounting without angles: If the lower case of the TabLines TWE is flat against the wall, you can mount the frame 4 directly on the backside of the wall. You don t need the angles. If the distance is too large, attach a piece of wood (e.g.) with the required depth and mount the frame. Fig. 4: Mounted angles Mounting with angles: If the cavity is too big, you need the angles. Mount the angles for example with two pieces of wood in the notch. Mount the frame on the angles. Mind the needed depth! 4
2.2.3 Insert the lower case Position the lower case 4 on the angles and fix thecasewiththedeliveredm4-bolts 1 onthe angles (fig. 5). Make sure that all screws have been tightened! Fig. 5: Mounting the lower case 2.2.4 Adjust the frame Because of the elongated holes in the lower case you can easily adjust the frame horizontally, even after tightening on the wall. When the TabLines TWEisinthedesiredposition,tightenthescrews again. With the M5-screws 2 you can do minor adjustments of the build-in depth of the frame to correct mistakes from before. Fig. 6: Frame can be adjusted 5
2.2.5 Insert the tablet Make sure that the homebutton of the tablet is at the bottom. Insert the tablet (fig. 7) between the insert strips (the insert strips are already attached). Make sure that the Samsung Galaxy Tab don t fall down during the installation. If possible, hold it the whole time until the cover is hooked in. Fig. 7: Integrated Samsung Galaxy Tab 2.2.6 Close the cover case Hookthecasecover 5 intothelowercase 4. Make sure that the cover case is hooked into the screws (fig. 8). You can still select the homebutton after closing the cover. Your tablet is mounted! Fig. 8: Hook in the case cover 6
2.3 Mounting on solid walls 2.3.1 Wall notch Select an area of the wall and draw the dimensions on it. Cut out or milling the selected area. Check the needed depth! The cover of the TWE has to be later flush on the wall. Fig. 9: Mark the position 2.3.2 Mount the lower case After cutting out the notch you can just screw the lower case 4 on the wall. Use the supplied M4 screws 1. Instead of the screws, you can also use special glue, foam or tape. Fig. 10: Sticked lower case 7
2.3.3 Insert the tablet Make sure that the homebutton of the tablet is at the bottom. Insertthetablet(fig.11)betweentheinsert strips (the insert strips are already attached). Make sure that the Samsung Galaxy Tab don t fall down during the installation. If possible, hold it the whole time until the cover is hooked in. Fig. 11: Integrated Samsung Galaxy Tab 2.3.4 Close the cover case Hookthecasecover 5 intothelowercase 4. Make sure that the cover case hooked into the screws (fig. 12). You can still select the homebutton after closing the cover. Your tablet is mounted! Fig. 12: Hook in the case cover 8
3. Anti-theft-protection Please note that you can only use this function, if you have purchased a TabLines TWE model with anti-theftprotection. The anti-theft-protection cannot be added subsequently. Use the provided hex-wrench 6 to screw the safety bolt in front of the case. The safety bolt is already integrated in the case. The anti-theft-protection prevents, that an unauthorised person can open the case. Fig. 13: Tighten the security screw 9