TECHNICAL DATA GENERAL INFORMATIONS Voltage nominal maximum for test 1 135 kv When mounting tube inserts adopt proper caution, in order to avoid glass bulb breaking and fragments projection. Please use protective gloves and glasses. Tube insert connected to H.V. supply is a radiation source: be sure to take all necessary safety cautions Inverse voltage Focal spots (IEC 6336:5) nominal maximum for test small large 1 135.5 1.5 kv mm Wash thoroughly with alcohol the external surface of tube insert (care of fire risk). Avoid contact of dirty surfaces with cleaned tube insert. Clamp system inside housing or self-contained units must not mechanically stress the tube. After installation, check the right working of the tube (no fluctuation of tube current nor crackling) Filament characteristics small large 2.4 4. V 3. 4. A 4. 8. V 3.5 4.5 A Anode material tungsten Target angle 12 Anode heat storage capacity 3* J Maximum anode cooling rate 27* W Comply with insert thermal parameters, planning and programming the exposure parameters and cooling pauses. Housing or self-contained units must be provided with an adequate thermic protection. Voltages indicated in charts are valid for transformer supplied with ground center. Tube inserts contain environment polluting materials, particularly lead liner tubes. Please apply to qualified operator for waste disposal, according to local regulation requirements. Nominal anode input power at.1 s (DC) small 78 large 4 W Inherent filtration.5 mm Al Maximum diameter 5 mm Overall length 155* mm INCIDENT REPORT ACCORDING TO 93/42/EEC MEDICAL DEVICES DIRECTIVE In order to comply with CE marking requirements, end users have to report to local Competent Authority all the informations about possible incidents involving the device, regarding any deterioration in its characteristics and performances, as well as any inaccuracies in this documentation, which might lead to or might have led to the death of patient / user or a deterioration in his state of health. This information must be promptly reported also to C.E.I. in order to start manufacturer reporting, as per above mentioned directive. * with standard shank. On every kind of shank it is possible to make customized millings for the allignement of the tube. 459 this mark assures device conformity to EC Directive 93/42 on Medical Devices Safety Rev.I 412 Original text: Italian Pag. 1 di 6 C.E.I. Srl via della Tecnica 3 San Lazzaro di Savena BOLOGNA - Italy
DIMENSIONS AND CONNECTIONS STD SHANK (Anode heat storage capacity 3 kj, Maximum anode cooling rate 27 W) large focus - red common - black Small focus-yellow raggi X THERMAL CURVES Heat storage (J) INSULATING CYLINDER LEAD Time (s) Rev.I 412 Original text: Italian Pag. 2 di 6 C.E.I. Srl via della Tecnica 3 San Lazzaro di Savena BOLOGNA - Italy
DIMENSIONS AND CONNECTIONS LONG SHANK (Anode heat storage capacity 33 kj, Maximum anode cooling rate 28 W) large focus - red common - black Small focus-yellow raggi X THERMAL CURVES Heat storage (J) LEAD INSULATING CYLINDER Time (s) Rev.I 412 Original text: Italian Pag. 3 di 6 C.E.I. Srl via della Tecnica 3 San Lazzaro di Savena BOLOGNA - Italy
DIMENSIONS AND CONNECTIONS RADIATOR (Anode heat storage capacity 4 kj, Maximum anode cooling rate 5 W) large focus - red common - black Small focus-yellow raggi X Heat storage (J) INSULATING CYLINDER Time (s) LEAD Rev.I 412 Original text: Italian Pag. 4 di 6 C.E.I. Srl via della Tecnica 3 San Lazzaro di Savena BOLOGNA - Italy
EMISSION CHARACTERISTICS FILAMENT CHARACTERISTICS DC 24 4.2 SMALL FOCAL SPOT (.5 IEC 336) 16 16 12 7 kv 7 kv 12 8 8 4 4 2.2 2.4 2.6 2.8 3. 3.2 3.4 3.6 2.2 2.4 2.6 2.8 3. 3.2 3.4 3.6 Filament current (A) 4.1 4. 3.9 3.8 3.7 3.6 3.5 3.4 3.3 3.2 2.4 2.8 3.2 3.6 4. LARGE FOCAL SPOT (1.5 IEC 336) 1 8 6 7 kv 4 4. 5. 6. 7. 8. 1 1 8 7 kv 6 4 4. 5. 6. 7. 8. Filament current (A) 4.5 4.4 4.3 4.2 4.1 4. 3.9 3.8 3.7 3.6 3.5 4. 5. 6. 7. 8. Rev.I 412 Original text: Italian Pag. 5 di 6 C.E.I. Srl via della Tecnica 3 San Lazzaro di Savena BOLOGNA - Italy
MAXIMUM RATING CHARTS DC SMALL FOCAL SPOT (.5 IEC 336) LARGE FOCAL SPOT (1.5 IEC 336) 4 kv 5 kv 6 kv 7 kv 8 kv 9 kv 1 kv 11 kv 1 kv 4 kv 5 kv 6 kv 7 kv 8 kv 9 kv 1 kv 11 kv 1 kv Rev.I 412 Original text: Italian Pag. 6 di 6 C.E.I. Srl via della Tecnica 3 San Lazzaro di Savena BOLOGNA - Italy