Features. High Brightness LED Light source

Transcription

1 Solid-State Lighting Series 6W MR16 DATASHEET Features High Brightness LED Light source Ecologically Friendly Energy Efficient

2 General Information... 1 Product Dimensions... 2 Product Information... 3 Technical Data... 3 Light Patterns... 4 Applications... 5 Environmental Friendly... 6 Product Safety... 7 Package Information... 8 Revision History... 8 About Edison Opto... 9

3 6W MR16 DATASHEET General Information Introduction Edison Opto 6W MR16 is based on high brightness LED source which provides a superior light illuminance. It is ideal for using in recessed, ceiling mounted and suspended light fixtures. The lamp features standard MR16 bi-pin, which can easily switch and replace from a standard halogen MR16 bulb.moreover, the product can be used in hard-to-reach locations to prevent regular maintenance needs. Furthermore, the multi- selection on various colors provides a great experience in decorative and mood lighting applications. 1

4 Product Dimensions Ø2 [Ø50mm] Ø1 5/8 [Ø42 mm] Ø2 [Ø50mm] Tolerance: ±2.5 mm Ø2 [Ø50mm] 2

5 Product Information Product Type 6W MR16 Product Order Code 7-MR16-11 WATT COLOR ANGLE DRIVER COVER BASE Code Type Code Type Code Type Code Type Code Type Code Type 06 6W CW (5,700K) NW (4,000K) WW (3,000K) WW (2,700K) Note: Available selection of Color, Beam angle, Driver. 2 20~ ~39 7 No Driver AC/ DC12V W0 White 05 GU5.3 (MR16) Technical Data Parameter Rating / Value Units Power Consumption 6 W Color Temperature 5,700/4,000/3,000/2,700 K AC/DC Input Voltage 12 V CRI CW 80 NW 80 WW 80 Weight 45 ± 5 g Base GU Operating Temperature -20 ~ +40 C Storage Temperature -40 ~ +60 C Notes: 1. Power consumption has 10% tolerance. 2. Color rendering index (CRI) is measured with accuracy in minimum. 3. Weight has ± 5 g tolerance. 4. The operating temperature* is based on the ambient temperature to the heatsink in 5 cm distance. -- 3

6 Technical Data Power Consumption (W) Beam Angle Color Typ. Flux (lm) Typ. (lx) Cool White 560 2, Neutral White 560 2,200 6W 15W Warm White 500 2,000 Cool White 560 1, Neutral White 560 1,400 Warm White 500 1,350 Notes: 1. LED is a dynamic and constantly evolving technology. The final lux output of your 6W MR16 may vary. 2. Angle has ±5 tolerance. Light Patterns 105 Beam Angle Beam Angle

7 6W MR16 DATASHEET Applications Recessed and suspended fixtures apply Ceiling mounted fixtures apply Retail stores, Hotel, Showroom 5

8 Environmentally Friendly To look at the increased demand of energy and the effect on global warming, Edison Opto plays the role in preserving the forest by reducing energy consumption, and CO2 emission one step at a time. Thanks to the replacement of traditional halogen lamp, one of 6W MR16 lighting application can help in reducing global warming by kg of CO2 annually. 6W MR16 VS 50W Halogen Power Reduction by 88% Reduction of CO2 = emission by 245.9kg = Saving 17.6 Trees a year KWh % Note : Calculation based on 24 hours of daily operation W Halogen lamp 6W MR16 6

9 Product Safety WARNING Risk of Electrical Shock, Injury, and damage Disconnect or turn off power before servicing or installing luminaire. Do not hot swap! LED heat sink module must not to be disconnected with line power on failure to do so may damage product. All wiring connections should be capped with UL approved recognized wire connectors. The luminaire shall, under no circumstance, be covered with thermal insulation matting or similar material, and pay attention not to exceed the maximum operation temperature of LED module. If the IP rating of the fixture should be higher than IP20, the design of the housing should be according to the IP standards in the application. The LED module itself and all its components must not be mechanically stressed. Assembly must not damage or destroy conducting paths on the circuit board. Be aware of, the luminaire is intended for indoor application and keep away from any chemicals. CAUTION Avoid direct eye exposure to the light source while it is on. Wear safety glasses and gloves during installation and servicing. Allow lamp/fixture to cool before handling. Do NOT touch enclosure or light source. Follow all manufacturers warnings, recommendations and restrictions for : burning position, mounting location/methods, and replacement. 7

10 Package Information 1pc / Pack 10 Packs / Box 10 Boxes / Carton Notes : 1. Pack Dimensions : 60mm(length)*55mm(width)*65mm(height) 2. Box Dimensions : 330mm(length)*120mm(width)*70mm(height) 3. Carton Dimensions : 368mm(length)*248mm(width)*350mm(height) 4. Figures not shown to scale. Revision History Versions Description Release Date 1 Establish order code information 2012/11/22 2 Update technical data 2013/10/01 3 Revise CCT of Cool White 2013/12/ Update photo of front page 2. Establish a New version 3. Add Product safety 2014/09/12 8

11 About Edison Opto Edison Opto is a leading manufacturer of high power LED and a solution provider experienced in LDMS. LDMS is an integrated program derived from the four essential technologies in LED lighting applications- Thermal Management, Electrical Scheme, Mechanical Refinement, Optical Optimization, to provide customer with various LED components and modules. More Information about the company and our products can be found at Copyright 2014 Edison Opto. All rights reserved. No part of publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photo copy, recording or any other information storage and retrieval system, without prior permission in writing from the publisher. The information in this publication are subject to change without notice. For general assistance please contact: service@edison-opto.com.tw For technical assistance please contact: LED.Detective@edison-opto.com.tw 9