INSTALLATION INSTRUCTIONS Accessory HARD ROOF (5P) P/N 0SR85-HL4-101 Application SXS1000M5D/M5P Honda Dealer: Please give a copy of these instructions to your customer. Publication No. MII 15262 Issue Date Revised December 2015 PARTS LIST (5) (1) (4) (3) No. Description Qty (1) Roof 1 (2) Cam lock 8 (3) Front-center bracket 2 (4) Front-side bracket 2 (5) Side bracket 2 (6) 6 mm flat washer 30 (7) 6 x 18 mm screw 16 (8) 6 x 20 mm screw 14 (9) Nylock nut 14 (10) Installation Instruction URL 1 (9) USE AND CARE INFORMATION Check the accessory mounts frequently and retighten if necessary. Replace this accessory with a new one if it is damaged or discolored excessively. When this accessory becomes dirty, rinse it thoroughly with cool water to remove loose dirt, then wipe with a clean cloth or sponge. Do not use a brush to clean this accessory as it may scratch the surface. Never use petroleum solvents such as gasoline, thinner, benzine, acid or alkaline cleaners. INSTALLATION NOTE: Remove and discard the rubber shipping band from the cam lock before installation of this accessory. SHIPPING BAND (DISCARD) TOOLS AND SUPPLIES REQUIRED 4 mm hex wrench Torque wrench 10 mm open-end wrench Power drill 5/16" (8 mm) drill bit TORQUE CHARTS Tighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts. Item N m kgf m lbf ft 6 mm screw and nut 5 0.5 4 2015 American Honda Motor Co., Inc - All Rights Reserved. 0SR85-HL4-101 1 of 6
TOP TOP OPTIONAL: LED LIGHT BAR PRE-INSTALLATION If you purchased the optional LED Light Bar (P/N 0SV31- HL4-301), complete the following steps to prepare the roof for later installation of this accessory. Print both template pages. Templates must be printed Actual Size. Cut out both templates, including the holes. Tape both templates together along the joining edge. Place the template over the surface of the roof as shown, aligning the holes in the template with the holes in the roof. Insert a 6 x 20 mm screw into each of the four holes to secure the template to the surface of the roof. Drill a hole through the roof at each crosshair on the template using a 5/16" (8 mm) drill bit. Remove the template. TEMPLATE 2. Repeat Step 1 for the remaining front-side bracket. 3. Loosely install the front-side, outer brackets to the roof using two 6 x 20 mm screws, flat washers, and nylock nuts per bracket. LOCK NUT 4. Install a front-center bracket to the bottom of a cam lock using two 6 x 18 mm screws and flat washers, noting the orientation of the cam lock as shown. ROOF 1. Loosely install a front-side bracket to the bottom of a cam lock using two 6 x 18 mm screws and flat washers, noting the orientation of the cam lock as shown. 6 x 18 mm SCREW 5. Repeat Step 3 for the remaining front-center bracket. 6. Loosely install the front-center brackets to the roof using two 6 x 20 mm screws, flat washers, and nylock nuts per bracket as shown. 6 x 18 mm SCREW LOCK NUT 2 of 6 0SR85-HL4-101 2015 American Honda Motor Co., Inc - All Rights Reserved.
7. Install two cam locks to the rear corners of the roof using two 6 x 18 mm screws and flat washers per cam lock as shown. The cam locks must open towards the rear edge of the roof, as shown. 10. Open all eight clamps on the underside of the roof. 11. Place the roof on the top of the cab frame and align the clamps around the cab frame bars. ROOF <REAR CORNER> CAB FRAME 6 x 18 mm SCREW 8. Install a cam lock to each of the side brackets using two 6 x 18 mm screws and flat washers per bracket. 12. Check that the roof is centered over the cab frame. Starting with the middle, snap closed each of the eight cam locks. Tighten all hardware to the specification in the Torque Chart. There should be no bulging near the base of the clamps or along the edges of the roof panel. If there is bulging, loosen the cam lock mounting hardware and adjust the fit as necessary. SIDE 6 x 18 mm SCREW 9. Install the side brackets to the roof using three 6 x 20 mm screws, flat washers, and nylock nuts per bracket as shown. NYLOCK NUT NYLOCK NUT SIDE 2015 American Honda Motor Co., Inc - All Rights Reserved. 0SR85-HL4-101 3 of 6
13. Adjust cam lock tension by rotating the threaded arm clockwise to tighten, counter-clockwise to loosen. THREADED ARM 4 of 6 0SR85-HL4-101 2015 American Honda Motor Co., Inc - All Rights Reserved.
Align with A <TEMPLATE> Roof, Driver Side Drill Template B NOTICE If you print this template from your local computer, make sure the printer settngs do not scale or shrink the page. TOP Drill here. 50mm 40 10 SCALE 20 30 SCALE 50mm 40 30 20 10 2015 American Honda Motor Co., Inc - All Rights Reserved. 0SR85-HL4-101 5 of 6
SCALE 10 20 30 40 50mm SCALE 40 50mm Drill here. 30 20 10 TOP Align with B If you print this template from your local computer, make sure the printer settngs do not scale or shrink the page. Roof, Passenger Side Drill Template A NOTICE <TEMPLATE> 6 of 6 0SR85-HL4-101 2015 American Honda Motor Co., Inc - All Rights Reserved.