INSTALLATION INSTRUCTIONS Accessory S Application 2011 CR-V Publications No. AII 44611 Issue Date AUG 2010 PARTS LIST 2 Wire ties with clip A Back-up Sensors Attachment Kit P/N 08V67-SWA-100B Back-up sensor control unit Wire tie with clip B Wire tie with clip C Buzzer 2 EPT sealers Back-up sensor harness Fuse label 2 Self-tapping screws Back-up sensor subharness Flange nut 2 Corner sensor clips Accessory User s Information Manual Center sensor clips Back-up Sensors Kit P/N 08V67-SWA-100J Control unit bracket 2 Center sensors (STOP) (Blue) Connector clip 2 Corner sensors (STOP) 4 Wire ties (White) 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 44611 (1008) 08V67-SWA-1B00-91 1 of 14
TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 8 mm, 10 mm, and 14 mm Sockets Pushpin Felt-tip pen Drill and 5 mm Drill bits 16 mm, 24 mm, and 26 mm Hole saws Scale Eye protection (safety goggles, face shield, etc.) 10 mm Combination wrench File Diagonal cutters Utility knife Plastic trim tool (T/N SILTRMTL 10) Blanket Isopropyl alcohol Shop towel T30 Torx bit Illustration of the Back-up Sensors installed on the Vehicle BACK-UP CORNER INSTALLATION FUSE (2A) CENTER S CORNER BUZZER BACK-UP CONTROL UNIT 931903BG Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: If you are also installing a trailer hitch, install the back-up sensor kit first. 1. Make sure you have the anti-theft code for the radio and navigation system, then write down the radio presets. 2. Disconnect the negative cable from the battery. 3. If equipped, remove the tonneau cover. TONNEAU COVER Pull. 2 of 14 AII 44611 (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
4. Remove the right rear door sill trim (three clips). RIGHT DOOR SILL TRIM 6. Remove the weatherstrip from around the rear trim panel. Remove the rear trim panel (two bolts with tie-down hooks, two clips, and four clips). 4 S 2 S 3 S TRIM 6222010B 2 TIE-DOWN HOOKS 5. Remove the cargo board (two hooks). WEATHERSTRIP 2 BOLTS 6627010B 7. Fold the rear seats forward, and remove the right rear lid from the cargo area right side trim (10 retaining tabs). CARGO AREA RIGHT SIDE TRIM RIGHT TRIM BRACKET CARGO BOARD HOOK 6410010B 10 RETAINING TABS BOLT RIGHT LID 6811060B 8. Remove the vehicle bolt from the right rear trim panel bracket. 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 44611 (1008) 3 of 14
9. Remove the rear door and tailgate weatherstrip from the cargo area right side trim panel. 12. Remove the right quarter pillar glass trim (seven clips). 8 S WEATHERSTRIP 7 S RIGHT QUARTER PILLAR GLASS TRIM WEATHERSTRIP CARGO AREA RIGHT SIDE TRIM 6905060B 6222060B 10. Remove the cargo area right side trim panel (10 clips). 11. Remove the seat belt from the right quarter pillar glass trim (one cover and one seat belt bolt). NOTE: Torque the seat belt bolt to 32 N m (24 lbf ft). 13. Remove the left rear splash guard (four selftapping screws). RIGHT QUARTER PILLAR GLASS TRIM SEAT BELT BOLT COVER SPLASH GUARD 4 SELF-TAPPING SCREWS 6620011Y SEAT BELT 6222050B 14. Remove the right rear splash guard (four selftapping screws). 4 of 14 AII 44611 (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
15. With the help of an assistant, remove the rear bumper (two bolt covers, two bolts, two flange bolts, and two clips). Place the rear bumper on a blanket. BOLT COVER 17. Get the back-up sensor harness. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the fuse label will attach. Attach the (2A ) label to the fuse case. FUSE CASE 2 FLANGE BOLTS FUSE LABEL (2A BACK-UP ) 6216030B 2 SCREWS 920901A 18. If the vehicle is equipped with a moonroof, release the moonroof drain hose (two hooks). 16. If equipped, remove the rear bumper absorber from the rear bumper beam. HOOK BEAM MOONROOF DRAIN HOSE 6509010B ABSORBER 6525560B 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 44611 (1008) 5 of 14
19. Inside the cargo area, remove the clip that secures the vehicle 6-pin connector to the vehicle panel, and unplug the vehicle 6-pin connector. 22. Wrap one EPT sealer around the back-up sensor harness 6-pin connector, and secure the 6-pin connector to the vehicle harness with one wire tie. 6-PIN WIRE TIE EPT SEALER 6-PIN 6-PIN BACK-UP 6-PIN 6-PIN 6311011B 20. Plug the back-up sensor harness into the vehicle 6-pin connector. Plug the other vehicle 6-pin connector into the other back-up sensor harness 6-pin connector. 21. Reinstall the vehicle 6-pin connector clip to the vehicle panel. 6-PIN 120 mm EDGE EPT SEALER BACK-UP 980501AB 23. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the EPT sealer will attach. Attach the EPT sealer to the edge of the vehicle panel in the area shown. 24. Slide the control unit bracket onto the control unit as shown. CONTROL UNIT 6311021B CONTROL UNIT BRACKET 932304AB 6 of 14 AII 44611 (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
25. Plug the back-up sensor harness 14-pin connector into the control unit. 28. Install the back-up sensor harness clip into the hole in the vehicle panel. CONTROL UNIT CONTROL UNIT BRACKET 14-PIN 6224060B 26. Attach the back-up sensor harness clip to the control unit bracket. 27. Insert the stud on the control unit bracket into the hole in the vehicle panel, making sure that the bracket tab is seated in the large hole. Secure the bracket to the vehicle panel using a 6 mm flange nut. 29. Using a utility knife, trim the right quarter pillar glass trim in the area shown. RIGHT QUARTER PILLAR GLASS TRIM 6224080B CONTROL UNIT CONTROL UNIT BRACKET STUD UTILITY KNIFE BRACKET TAB 5 mm Cut off. RIB 932308AB LARGE 6 mm FLANGE NUT 6311041B 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 44611 (1008) 7 of 14
30. Using a scale and a felt-tip pen, measure and mark the right quarter pillar glass trim in the area shown. 33. Using a pushpin, pierce the center marked position of the right quarter pillar glass trim. RIGHT QUARTER PILLAR GLASS TRIM S FELT-TIP PEN 16 mm 20 mm 20 mm RIB RIB 22.5 mm 6.5 mm RIB 31. Using a pushpin, pierce the two outer marked positions of the right quarter pillar glass trim. S 6.5 mm 962502BB 5 mm BIT RIGHT QUARTER PILLAR GLASS TRIM BIT 963006AB 34. While wearing eye protection, drill the pierced center mark to 16 mm. First drill with a drill bit, and finish with a 16 mm hole saw. Remove any burrs. 35. Using isopropyl alcohol on a shop towel, clean the right quarter pillar glass trim where the double-sided tape will attach. Remove the adhesive backing from the buzzer. Route the buzzer 2-pin connector through the 16 mm hole, and install the buzzer to the right quarter pillar glass trim with two self-tapping screws. Install it with the on/off switch and the volume control toward the front of the vehicle. RIGHT QUARTER PILLAR GLASS TRIM DOUBLE-SIDED TAPE SWITCH BUZZER ADHESIVE BACKING RIGHT QUARTER PILLAR GLASS TRIM 6224101B VOLUME CONTROL 32. While wearing eye protection, drill the two pierced marks to 5 mm. First drill with a drill bit, and finish with a 5 mm drill bit. 5 mm 16 mm 5 mm 2 SELF- TAPPING SCREWS BUZZER 2-PIN 6822011B 36. Reinstall the right quarter pillar glass trim. 8 of 14 AII 44611 (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
37. Plug the back-up sensor harness 2-pin connector into the buzzer 2-pin connector. 41. At the right rear corner of the vehicle, remove the vehicle grommet. Without a Vehicle Harness WIRE TIE WITH B 2-PIN BUZZER 6-PIN GROMMET WIRE TIE cargo area outside 2-PIN BUZZER 2-PIN 38. Secure the 2-pin connector: 2-PIN 962503BB With a vehicle harness, secure the 2-pin connector to the vehicle harness with a wire tie. Without a vehicle harness, secure the 2-pin connector to the vehicle panel with one wire tie with clip B. 39. Secure the back-up sensor harness to the vehicle harness with one wire tie. BUZZER 6227010B 42. Route the back-up sensor subharness 6-pin connector through the hole where the vehicle grommet was removed, and seat the back-up sensor subharness grommet into the vehicle panel hole. 43. Install the connector clip to the back-up sensor subharness 6-pin connector. BACK-UP GROMMET (Discard.) 6-PIN 6-PIN BUZZER Bundle up the excess. BACK-UP BACK-UP WIRE TIE WIRE TIE WITH C 972101AD 40. Bundle up the excess buzzer harness, and secure it to the vehicle panel with one wire tie with clip C. 6-PIN 6227020B 44. Plug the back-up sensor subharness 6-pin connector into the back-up sensor harness 6-pin connector, and install the connector clip. Secure the clip in the vehicle panel hole in the area shown. 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 44611 (1008) 9 of 14
45. Route the back-up sensor subharness as shown, and install the back-up sensor subharness clip into the vehicle panel hole. 46. Route the back-up sensor subharness as shown. Install the back-up sensor subharness clips into the holes in the vehicle panel. With rear bumper beam: Secure the subharness to the rear bumper beam with one wire tie at the green tape. GREEN TAPE WIRE TIE BEAM BEAM 931702AG Without rear bumper beam: Secure the subharness to the stud on the vehicle panel with one wire tie with clip A at the green tape. WIRE TIE WITH A GREEN TAPE 47. Route the back-up sensor subharness as shown. With rear bumper beam: Secure the subharness to the rear bumper beam with one wire tie at the green tape. BEAM BACKUP SUB BACKUP SUB GREEN TAPE 931801AG WIRE TIE STUD BEAM 931703AG 931802AG 10 of 14 AII 44611 (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
Without rear bumper beam: Secure the subharness to the stud on the vehicle panel with one wire tie with clip A at the green tape. GREEN TAPE WIRE TIE WITH A 49. Inside the rear bumper on the passenger s side, locate the two back-up sensor scribe marks. Using a pushpin, pierce the center and top for both the outboard and the inboard scribe marks. There are several marks on the inside of the rear bumper; make certain that you locate and pierce the proper scribe marks. OUTBOARD INBOARD STUD 931803AG 48. Inside the rear bumper on the driver s side, locate the two back-up sensor scribe marks. Using a pushpin, pierce the center and bottom of the outboard scribe marks, and pierce the center and top of the inboard scribe marks. There are several marks on the inside of the rear bumper; make certain that you locate and pierce the proper scribe marks. 980503AB INBOARD OUTBOARD 980502AB 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 44611 (1008) 11 of 14
50. While wearing eye protection, drill a hole at each of four pierced points you made in the center of the rear bumper. NOTE: Drill from the painted side of the bumper. 52. While wearing eye protection, drill a hole at each of four pierced points you made in each corner of the rear bumper. NOTE: Drill from the painted side of the bumper. BIT 2 S BIT 2 S 26 mm SAW 24 mm 24 mm SAW 26 mm 26 mm 931805AG 24 mm SAW 24 mm Passenger s side of the bumper. 2 S BIT 932401AG Driver s side of the bumper. Enlarge the lower holes using a 26 mm hole saw. Enlarge the upper hole using a 24 mm hole saw. Passenger s side of the bumper. 51. Enlarge the lower holes using a 26 mm hole saw. NOTE: Drill from the painted side of the bumper. Remove all burrs. Driver s side of the bumper. Enlarge the lower hole using a 24 mm hole saw. 53. On the passenger s side of the bumper, enlarge the bottom hole to 24 mm using a 24 mm hole saw. On the driver s side of the bumper, enlarge the upper hole to 24 mm using a 24 mm hole saw. NOTE: Drill from the painted side of the bumper. Remove all burrs. 12 of 14 AII 44611 (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.
54. On the passenger s side of the rear bumper, install the corner sensor (white) and the center sensor (blue) to the rear bumper using one corner sensor clip, and one center sensor clip. Be sure the sensors are seated properly. 55. On the driver s side of the rear bumper, install the corner sensor (white) and the center sensor (blue) to the rear bumper using one corner sensor clip, and one center sensor clip. Be sure the sensors are seated properly. 26 mm CENTER CENTER (Blue) CENTER (Blue) CENTER (Blue) 26 mm CENTER (Blue) CENTER 24 mm 24 mm CORNER (White) CORNER (White) CORNER 931806AG CORNER (White) CORNER CORNER (White) 931807AG 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 44611 (1008) 13 of 14
56. If the vehicle is equipped with a rear bumper absorber, use a utility knife to trim each end of absorber using the measurements and scribe marks shown. 58. With the help of an assistant, bring the rear bumper near the vehicle, plug in the four back-up sensor subharness 2-pin connectors into the sensors, and attach the two subharness clips to the two center sensor clips. Reinstall the rear bumper. UTILITY KNIFE 30 mm Cut off. 4 2-PIN S CORNER ABSORBER Cut off. 50 mm UTILITY KNIFE CENTER CENTER CORNER CENTER (White) 2 BACK-UP S 931808AG ABSORBER 57. Reinstall the rear bumper absorber to the rear bumper beam. 931901B 59. Check that all wire harnesses are routed properly and that all connectors are plugged in. 60. Reinstall all removed parts. 61. Reconnect the negative cable to the battery. 62. Enter the anti-theft codes for the radio and navigation systems, then enter the customer s radio presets. 63. Reset the clock. 64. Check that the back-up sensors work properly as described in the Accessory User s Information Manual supplied with the back-up sensor attachment kit. 14 of 14 AII 44611 (1008) 2010 American Honda Motor Co., Inc. All Rights Reserved.