GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Side Window Pathfinder (2013) 999D3 XZ000 Item Qty. Part Description Service Part Number A 1 Side Window -Front LH --- B 1 Side Window -Front RH --- C 1 Side Window -Rear LH --- D 1 Side Window -Rear RH --- E 8 Bracket A --- F 2 Bracket B --- G 10 Capped Screw --- H 10 Washer --- I 10 Nut --- J 1 Nut Tool --- K 10 --- L 2 Alcohol Wipe - 2 pk --- M 1 Installation Instruction Replacement Template 999V2 AW000 A B C D E F G H I J K L M TOOLS REQUIRED: Clean Cloth Soap/Water 90% or great isopropyl alcohol Masking Tape Scale/Measuring Tape (mm) Non Permanent Marker / Pencil PRE-INSTALLATION WARNINGS, CAUTIONS, CRITICAL STEPS, and NOTES: Read all instructions carefully before beginning installation. Never use ammonia based cleaner or solvents on the hood protector Dealer Installation Recommended. No moisture contact or washing vehicle for 24 hours after installation. Ideal ambient temperature for installation is above 55 (15 C). Page 1 of 9 999D3 XZ000 II Rev. 7/18/2012
Fig. 1 1) 2) Clean front door with soap/water and dry with a clean cloth. Lower window and pull rubber weather strip down to expose door flange and mirror sail edge. Pull Fig. 2 3) Clean installation surface (shaded area) with provided alcohol wipe. Clean shaded area 5) Flush 5) Flush Fig. 3 4) 5) Align front flange of deflector over mirror sail at step in both parts. Dry fit deflector by aligning top of deflector edge flush to top of door frame. Detail A Detail A 4) Align Steps Page 2 of 9 999D3 XZ000 II Rev. 7/18/2012
6) Detail A Fig. 4 6) Place masking tape on roof surface and mirror sail at bracket hole locations and mark with pen or pencil. 6) Detail A 6) Detail A Detail A Mark 6) Masking Tape Roof Surface 7) 5mm 7) Place abrasive tape with 5mm contacting door surface and mirror surface centered to marked tape locations (see detail A). Inner Door Flange 8) Wrap abrasive tape into inner door flange (see detail A). Abrasive Tape 8) Wrap Fig. 5 9) 10) Attach Bracket A using a capped screw through deflector and bracket. With capped screw through deflector and bracket, place washer and nut on capped screw. 11) Loosely tighten nut with nut tool. NOTE: Do not fully tighten screws. Section A Bracket A Capped Screw Washer Nut Nut tool Page 3 of 9 999D3 XZ000 II Rev. 7/18/2012
Fig. 6 12) Attach deflector to door by sliding brackets onto door flange. NOTE: Make sure liner pull tabs are exposed. Section View - Door Flange Door flange Bracket 13) Flush 16) Flush Fig. 7 13) 14) Align top of deflector edge flush to top of door frame at marked front location. Align front flange of deflector over mirror sail at step in both parts. 15) Pull front pull tab back about 1" and tack down deflector. 15) Pull 1" 17) Pull 16) 17) Align top of deflector edge flush to top of door frame at marked rear location. Pull vertical pull tab to remove liner and tack down deflector in place. 19) Remove Fig. 8 18) 19) Remove tape liner by pulling on exposed pull tab. Remove masking tape. 19) Remove 19) Remove 18) Pull Page 4 of 9 999D3 XZ000 II Rev. 7/18/2012
Push (min 15lbs) Fig. 9 20) Using a clean cloth apply at least 15 lbs. of pressure along tape length. Tighten Fig. 10 21) Use nut tool and tighten nuts on brackets. Tighten Nut Tool Fig. 11 22) Place Bracket B onto mirror sail. 23) Attach Bracket B to deflector by using a capped screw through deflector and bracket. 24) 25) With capped screw through deflector and bracket, place washer and nut on capped screw. Tighten nut with nut tool. Section A Capped Screw Mirror Sail Abrasive Tape 26) Push Nut Washer Bracket B Nut Tool 26) If exposed, push foam seal under deflector flange with credit card. 27) Place rubber weather strip back into door channel. Page 5 of 9 999D3 XZ000 II Rev. 7/18/2012
Fig. 12 28) 29) Clean rear door with soap/water and dry with a clean cloth. Lower window and pull rubber weather strip down to expose door flange. Pull Fig. 13 30) Clean installation surface (shaded area) with provided alcohol wipe. Clean shaded area 31) Flush 31) Flush Fig. 14 31) 32) Dry fit deflector by aligning top of deflector edge flush to top of door frame at marked locations. Line up front vertical edge 5mm away from edge of door frame. 32) 5mm Page 6 of 9 999D3 XZ000 II Rev. 7/18/2012
33) Detail A 33) Detail A Fig. 15 33) Place masking tape on roof surface at bracket locations and mark with pen or pencil. Detail A 33) Masking Tape 33) Mark Roof Surface 34) 5mm 34) Place abrasive tape with 5mm contacting door surface and centered to marked tape locations. See detail A. Inner Door Flange 35) Wrap abrasive tape into inner door flange. See detail A. 35) Wrap Fig. 16 36) 37) Attach Bracket A using a capped screw through deflector and bracket. With capped screw through deflector and bracket place washer and nut on capped screw. 38) Loosely tighten nut with nut tool. NOTE: Do not fully tighten screws. Section A Bracket A Capped Screw Washer Nut Nut tool Page 7 of 9 999D3 XZ000 II Rev. 7/18/2012
Fig. 17 39) Attach deflector to door by sliding brackets onto door flange. NOTE: Make sure liner pull tabs are exposed. Section View - Door Flange Door flange Bracket 40) Flush 40) Flush Fig. 18 40) Align top of deflector edge flush to top of door frame at marked front location. 41) Line up front vertical edge 5mm away from edge of door frame. 42) Pull 41) 5mm 45) Pull 42) Pull front vertical pull tab and remove liner. 43) Tack down deflector in place 44) Align top of deflector edge flush to top of door frame at marked rear location. 45) Pull vertical pull tab and remove liner. 46) Tack down deflector in place 48) Remove 48) Remove 47) Pull Fig. 19 47) Pull 47) 48) Remove tape liner by pulling on exposed pull tabs. Remove masking tape. Page 8 of 9 999D3 XZ000 II Rev. 7/18/2012
Push (min 15lbs) Fig. 20 49) Using a clean cloth apply at least 15 lbs. of pressure along tape length. Tighten Tighten Fig. 21 50) Use nut tool and tighten nuts on brackets. 51) Push rubber weather strip back into door channel. Nut Tool 52) Repeat steps 1-51 for other side. Page 9 of 9 999D3 XZ000 II Rev. 7/18/2012