SMART HIFI WIRELESS HEADPHONE WITH TOUCH CONTROL Headblue 1 INSTRUCTION
Start here Following items are included USB cable
Product overview 1 2 3 1.Volume down 2.Volume up 3.EQ button 4.Multifunction button 5.Trackback 6.Trackforward 7.LED indicator 8.Microphone 9.Charger connector 5 6 7 4 8 9
Basic operation Adjust the volume Press the "+" or "-" button to turn volume up or down, you hear beep voice prompts once reach the maximum or minimum. LED indicator and voice prompts Instruction Power on Power off Pairing Standby Incoming call Battery low Charging LED status Flashes blue twice Flashes red once Flashes red and blue alternately Flashes blue once every 8 seconds Flashes blue continuously Flashes red twice every 2 seconds Flashes red while charging Flashes blue once fully charged Voice prompts Beep Tone from high to low Tone from low to high / Continuous tone Warning tone /
Pairing Pair one phone 1. Press and hold the multifunction button for about 5 seconds, the LED indicator flashes red and blue, you hear voice prompt tone from low to high. 2. Activate the Bluetooth feature on your phone, and set it to search for new Bluetooth devices. Bluetooth ON Search
3. Select Headblue1. If you phone asks, enter 0000 (four zeros) for the passcode or accept the connection. The LED indicator stops flashing red and blue once successfully paired. Note:When the headphone and phone have been paired once, they will automatically connect when the headphone is on and Bluetooth is activated on the phone. Bluetooth ON Headblue1 Connect
Pair another phone Multipoint technology enables you to pair another phone and take a call from either. To pair with another mobile phone, follow the steps for Pair One Phone. After pairing successfully, restart the headphone to connect to 2 paired mobile phone automatically. Bluetooth ON Headblue1 Bluetooth ON Headblue1 Connect Connect
Call Answer a call Press the multifunction button once. When call rings,the LED indicator flashes blue continuously, you hear voice prompt of continuous tone. End a call Press the multifunction button once. Reject a call Press the multifunction button for 2 seconds. When call rings,the LED indicator flashes blue continuously, you hear voice prompt of continuous tone. Redial last call Double-press the multifunction button, and the mobile phone will redial the last call number. Switch between the headphone and phone Press the "<<" button for about 2 seconds to switch between headphone and phone during a call.
Music (Need media player support) Music play / pause Press multifunction button to play / pause music. (Some phones may require you to start a media player first), you hear "toot" once. Trackback Press "<<" button to skip track backward, you hear "toot" once. Trackforward Press ">>" button to skip track forward, you hear "toot" once. Fast forward Press and hold >> button until fast-forward begins. When you want to resume normal playback, release the >> button.
Rewind Press and hold << button until begins to rewind. When you want to resume normal playback, release the << button. EQ setting Press the EQ button to cycle through EQ setting: original, bass, treble, rock, pop. Note: the default EQ setting is original, the EQ setting will be restored to default once headphone restart. Switch music and calls When a call rings during a music playing, the music automatically pauses to allow you to answer or ignore the call. Once the call is ignored or ends, the music is resumed.
More features Voice dial (Need phone support.) Press the multifunction button for 2 seconds, you hear "toot", wait for phone prompt and then tell the phone to dial the name of a stored contact. Battery indicator The current battery status of headphone will be displayed in top right corner after the headphone connected to ios devices.
Listen music via USB cable (Microphone is disabled in this mode) 1. Connect the headset to a USB slot of PC using the supplied micro-usb cable. 2. The driver may need to be installed for the first time, after the driver installed successfully, sets headphones CSR8645 as default playback device (Refer to Computer OS instruction). 3. Turn on the music player on your computer, and then you enjoy music of computer via your headphone.
Charging Your new headphone has enough power to pair and make a few calls. When battery is low, you will hear the warning tone. It takes 2.5 hours to fully charge the headphone. While charging, the battery indicator light is red, the indicator light flashes blue once charging is complete. Note: The lifetime of the battery will be significantly reduced if your headphone is left uncharged for a long period. We recommend that recharge your headphone at least once a month.
Clear paired list Turn off the headphone, press and hold the multifunction button and EQ button simultaneously, then connect the headphone to a USB charger or USB port of computer, LED indicator flashes red, release multifunction button and EQ button after 4 seconds, paired list is cleared. Hardware reset Turn on the headphone, press and hold the multifunction button, connect the headphone to a USB charger or USB port of computer, the LED indicator flashes red, hardware reset is done in about 2 seconds.