CISCO ROUTERLAR İLE ISDN BRI DATA HABERLEŞMESİ UYGULAMASI



Similar documents
How To Configure A Cisco Router With A Cio Router

Course "Netzwerke" LAB 2 Basic Router Configuration

Configuring Link Aggregation

PA-MC-T3 Multi-Channel T3 Synchronous Serial Port Adapter Enhancement

Lab Configuring Basic Router Settings with the Cisco IOS CLI

Cisco Quality of Service and DDOS

Configuring the Switch for the Firewall Services Module

APOSTILA DE REDES DE COMPUTADORES PARTE VI SWITCH

Chapter 2 Lab 2-2, EIGRP Load Balancing

section examines how to configure leased lines between two routers using HDLC and PPP.

Laboratorio 3 Comunicación sincrónica Vía Satélite

Troubleshooting Second B channel Call Failures on ISDN B

Configuring ISDN Special Signaling

Chapter 3 Using Maintenance & Troubleshooting Tools & Applications Objectives

Overview of Access VPNs and Tunneling Technologies

Table of Contents. Cisco Configuring a Basic MPLS VPN

Laboratorio 4. Comunicación sincrónica Vía Satélite

CertificationKits.com EIGRP Sample CCNA Lab. EIGRP Routing. The purpose of this lab is to explore the functionality of the EIGRP routing protocol.

Configuring InterVLAN Routing and ISL/802.1Q Trunking on Catalyst 2900XL/3500XL/2940/2950/2970 Series Switches Using an External Router

Analysis of Basic Quality of Service Mechanism for Voice over IP In Hamdard University Network Campus

- Switch Port Configuration -

Basic Router Configuration

IOS NAT Load Balancing with Optimized Edge Routing for Two Internet Connections

Ubigate Quick Reference Guide for Covad. Document Type. Release Note. No of Pages. Item Code. Quick Reference Guide for Ubigate 1000 Page 1

CCIE R&S Lab Workbook Volume I Version 5.0

Configuring Dial Backup and Remote Management

Lab 4.2 Challenge Lab: Implementing MPLS VPNs

- QoS and Queuing - Queuing Overview

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and

Lab Load Balancing Across Multiple Paths Instructor Version 2500

Lab 7-1 Configuring Switches for IP Telephony Support

How To Configure InterVLAN Routing on Layer 3 Switches

Frame Mode MPLS Implementation

Configuring a Basic MPLS VPN

CCNP ROUTE 6.0 Student Lab Manual

Lab: Basic Router Configuration

Cisco DSL Router Configuration and Troubleshooting Guide PPPoA Troubleshooting

Objectives. Router as a Computer. Router components and their functions. Router components and their functions

Troubleshooting IP Routing

IOS NAT Load Balancing for Two ISP Connections

This chapter covers the following topics: ADSL Overview Cisco 6160 DSLAM Overview Cisco 6400 UAC Overview DSL Access Architectures and Protocols

Configuring a Leased Line

Cisco 850 Series and Cisco 870 Series Access Routers Software Configuration Guide

isco Troubleshooting Input Queue Drops and Output Queue D

Chapter 7 Lab 7-1, Configuring Switches for IP Telephony Support

Leased Line Support for Cisco 2600/3600 Series Analog Modems

Dynamic routing protocols over IPSec tunnels between Palo Alto Networks and Cisco routers

Special ISDN Signaling Commands

Lab 5-5 Configuring the Cisco IOS DHCP Server

Configuring Static and Dynamic NAT Simultaneously

Troubleshooting Layer 2 Protocols over T1 Using the CLI

OSPF Configuring Multi-Area OSPF

The Bryant Advantage Cisco Certified Network Associate Command Reference. 150 Commands Every CCNA Must Know!

Configuring the Firewall Management Interface

CCNP2 - Implementing Secure Converged Wide-area Networks v5.0

Troubleshooting Layer 2 Protocols Over T1 Using the CLI

IPv6 Hands-on Lab. Faraz Shamim, Technical Leader Harold Ritter, Technical Leader. Toronto, Canada May 30, 2013

> Avaya / Cisco Interoperability Technical Configuration Guide. Ethernet Routing Switch

isco Connecting Routers Back to Back Through the AUX P

How To Lower Data Rate On A Network On A 2Ghz Network On An Ipnet 2 (Net 2) On A Pnet 2 On A Router On A Gbnet 2.5 (Net 1) On An Uniden Network On

ASA 9.x EIGRP Configuration Example

High-Level Data Link Control

Cisco DSL Router Configuration and Troubleshooting Guide PPPoE: DSL Router as a PPPoE Client Troubleshooting

Cisco Certified Network Associate Exam. Operation of IP Data Networks. LAN Switching Technologies. IP addressing (IPv4 / IPv6)

Chapter 2 Lab 2-2, Configuring EtherChannel Instructor Version

Configuring a Lan-to-Lan VPN with Overlapping Subnets with Juniper NetScreen/ISG/SSG Products

1/2 Port Channelized T1/E1 PRI Network Module (NM-1CE1T1-PRI and NM-2CE1T1-PRI)

Basic Software Configuration Using the Cisco IOS Command-Line Interface

Cisco 12 CCNA Certification

Configuring Asynchronous SLIP and PPP

Configure ISDN Backup and VPN Connection

Release Notes for Cisco C881G-U-K9

LAB MANUAL for Computer Network

Cisco Configuring Commonly Used IP ACLs

IP Routing Configuring Static Routes

For T1 / E1, an NT NeTwork device must be connected to a TE Terminal Equipment device; NT must connect to TE.

Channelized E1 and Channelized T1 Setup Commands

Provisioning Dial Access to MPLS VPN Integration

Introduction about cisco company and its products (network devices) Tell about cisco offered courses and its salary benefits (ccna ccnp ccie )

Troubleshooting Tools

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and

! encor en etworks TM

Configuring POS. POS on the ML-Series Card. ML-Series SONET and SDH Circuit Sizes CHAPTER

Subnetting,Supernetting, VLSM & CIDR

TCP/IP Fundamentals. OSI Seven Layer Model & Seminar Outline

Effect of Windows XP Firewall on Network Simulation and Testing

Configuring Serial Interface WAN and LAN for SSG Firewall/VPN Products

GLBP Gateway Load Balancing Protocol

Lab 5.5 Configuring Logging

Nationwide WAN + VoIP connectivity

CCNP CISCO CERTIFIED NETWORK PROFESSIONAL LAB MANUAL

VOIP-211RS/210RS/220RS/440S. SIP VoIP Router. User s Guide

Transport and Network Layer

BASIC TCP/IP NETWORKING

ISDN. rek. Petr Grygárek Petr Grygarek, Advanced Computer Networks Technologies 1

Cisco Certified Network Associate (CCNA ) Version 22.0

Transcription:

CISCO ROUTERLAR İLE ISDN BRI DATA HABERLEŞMESİ UYGULAMASI Gökhan AKIN İTÜ 2003 TOPOLOJİ: İSTENENLER: 1. Topolojiyi Legacy DDR tekniği ile kurunuz. 2. Aynõ Topolojiyi Dialer Profile tekniğini kullanarak kurunuz. SANTRAL TELEFON NUMARALARI: PORT NO: TELEFON NOLARI: 1 130-131 -132 2 133-134 -135 3 136-137 -138 4 139-140 -141 5 142-143 -144 6 145-146 -147 7 148-149 -150 8 151-152 -153 9 154-155 -156 10 157-158 -159 11 160-161 -162 12 163-164 -165 1

ÇÖZÜMLER: 1- LEGACY DDR İLE ISTANBUL interface Loopback0 ip address 192.168.1.1 255.255.255.0 interface BRI0 ip address 192.168.0.1 255.255.255.0 dialer map ip 192.168.0.2 133 encapsulation ppp dialer-group 1 isdn switch-type basic-net3 ip route 192.168.2.0 255.255.255.0 192.168.0.2 dialer-list 1 protocol ip permit ANKARA interface Loopback0 ip address 192.168.2.1 255.255.255.0 interface BRI0 ip address 192.168.0.2 255.255.255.0 dialer map ip 192.168.0.1 130 encapsulation ppp dialer-group 1 isdn switch-type basic-net3 ip route 192.168.1.0 255.255.255.0 192.168.0.1 dialer-list 1 protocol ip permit 2

KONTROL KOMUTLARI ANKARA#sh ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is not set C 192.168.0.0/24 is directly connected, BRI0 S 192.168.1.0/24 [1/0] via 192.168.0.1 C 192.168.2.0/24 is directly connected, Loopback0 ANKARA#debug isdn q921 debug isdn q921 is ON. ANKARA#ping 192.168.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds: Dec 28 16:17:25.563: ISDN BR0 Q921: User TX -> IDREQ ri=1463 ai=127 Dec 28 16:17:25.643: ISDN BR0 Q921: User RX <- IDASSN ri=1463 ai=65 Dec 28 16:17:25.647: ISDN BR0 Q921: User TX -> SABMEp sapi=0 tei=65 Dec 28 16:17:25.683: ISDN BR0 Q921: User RX <- UAf sapi=0 tei=65 Dec 28 16:17:25.683: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 65 changed to up Dec 28 16:17:25.687: ISDN BR0 Q921: User TX -> INFO sapi=0 tei=65, ns=0 nr=0 Dec 28 16:17:25.731: ISDN BR0 Q921: User RX <- RR sapi=0 tei=65 nr=1 Dec 28 16:17:25.843: ISDN BR0 Q921: User RX <- INFO sapi=0 tei=65, ns=0 nr=1 Dec 28 16:17:25.847: ISDN BR0 Q921: User TX -> RR sapi=0 tei=65 nr=1 Dec 28 16:17:26.255: ISDN BR0 Q921: User RX <- INFO sapi=0 tei=65, ns=1 nr=1 Dec 28 16:17:26.255: ISDN BR0 Q921: User TX -> RR sapi=0 tei=65 nr=2 Dec 28 16:17:26.351: ISDN BR0 Q921: User RX <- INFO sapi=0 tei=65, ns=2 nr=1 Dec 28 16:17:26.355: ISDN BR0 Q921: User TX -> RR sapi=0 tei=65 nr=3 Dec 28 16:17:26.355: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up. Success rate is 80 percent (4/5), round-trip min/avg/max = 28/30/32 ms Dec 28 16:17:26.359: ISDN BR0 Q921: User TX -> INFO sapi=0 tei=65, ns=1 nr=3 3

Dec 28 16:17:26.439: ISDN BR0 Q921: User RX <- RR sapi=0 tei=65 nr=2 Dec 28 16:17:27.359: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, cha nged state to up ANKARA#sh dialer BRI0 - dialer type = ISDN Dial String Successes Failures Last DNIS Last status 130 1 0 00:00:25 successful 0 incoming call(s) have been screened. 0 incoming call(s) rejected for callback. BRI0:1 - dialer type = ISDN Idle timer (120 secs), Fast idle timer (20 secs) Wait for carrier (30 secs), Re-enable (15 secs) Dialer state is data link layer up Dial reason: ip (s=192.168.0.2, d=192.168.1.1) Time until disconnect 115 secs Connected to 130 (MERKEZ) BRI0:2 - dialer type = ISDN Idle timer (120 secs), Fast idle timer (20 secs) Wait for carrier (30 secs), Re-enable (15 secs) ANKARA#sh interfaces bri 0 BRI0 is up, line protocol is up (spoofing) Hardware is PQUICC BRI Internet address is 192.168.0.2/24 MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, loopback not set Last input 00:00:07, output never, output hang never Last clearing of "show interface" counters 00:01:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/16 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 48 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 15 packets input, 92 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 15 packets output, 84 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 1 carrier transitions 4

ANKARA# ANKARA#sh interfaces bri 0:1 BRI0:1 is up, line protocol is up Hardware is PQUICC BRI MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, LCP Open Open: CDPCP, IPCP, loopback not set idle 00:01:26 Last input 00:00:33, output 00:00:03, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/16 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 48 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 181 packets input, 14097 bytes, 0 no buffer Received 41 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 185 packets output, 14253 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 8 carrier transitions 5

ÇÖZÜMLER: 1- DIALER PROFILE İLE ISTANBUL interface Loopback0 ip address 192.168.1.1 255.255.255.0 interface BRI0 no ip address dialer pool-member 1 isdn switch-type basic-net3 interface Dialer0 ip address 192.168.0.1 255.255.255.0 encapsulation ppp dialer pool 1 dialer string 133 dialer-group 1 ip route 192.168.2.0 255.255.255.0 Dialer0 dialer-list 1 protocol ip permit ANKARA interface Loopback0 ip address 192.168.2.1 255.255.255.0 interface BRI0 no ip address dialer pool-member 1 isdn switch-type basic-net3 interface Dialer0 ip address 192.168.0.2 255.255.255.0 encapsulation ppp dialer pool 1 dialer string 130 dialer-group 1 ip route 192.168.1.0 255.255.255.0 Dialer0 dialer-list 1 protocol ip permit 6

KONTROL KOMUTLARI ISTANBUL#ping 192.168.2.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds: Dec 29 04:43:12.355: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 76 changed to up Dec 29 04:43:12.963: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up. Success rate is 80 percent (4/5), round-trip min/avg/max = 28/30/32 ms Dec 29 04:43:12.967: %DIALER-6-BIND: Interface BR0:1 bound to profile Di0 Dec 29 04:43:13.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, cha nged state to up ISTANBUL#sh interfaces dialer 0 Dialer0 is up, line protocol is up (spoofing) Hardware is Unknown Internet address is 192.168.0.1/24 MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, loopback not set DTR is pulsed for 1 seconds on reset Interface is bound to BR0:1 Last input never, output never, output hang never Last clearing of "show interface" counters 00:53:44 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/16 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 42 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 265 packets input, 20741 bytes 265 packets output, 20767 bytes Bound to: BRI0:1 is up, line protocol is up Hardware is PQUICC BRI MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, LCP Open Open: CDPCP, IPCP, loopback not set idle 00:01:41 Interface is bound to Di0 (Encapsulation PPP) 7

Last input 00:00:02, output 00:00:18, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 289 packets input, 21029 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 289 packets output, 21055 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 10 carrier transitions ISTANBUL# 8