APOSTILA DE REDES DE COMPUTADORES PARTE VI SWITCH
|
|
|
- Poppy Golden
- 7 years ago
- Views:
Transcription
1 APOSTILA DE REDES DE COMPUTADORES PARTE VI SWITCH 1
2 1. Criando um Banner de Login REDE DE COMPUTADORES VI SALESIANO#conf t SALESIANO(config)#banner motd c Enter TEXT message. End with the character 'c'. ################################################ # MENSAGEM!!!! # ################################################c SALESIANO(config)# 2. Verificando um Banner de Login SALESIANO (config)#^z exit SALESIANO con0 is now available Press RETURN to get started. ################################################ # MENSAGEM!!!! # ################################################ SALESIANO > 3. Setando Data e Hora no Switch clock set 15:13:00 14 Apr 2010 sh clock *15:13:3.558 UTC qua abr
3 4. Comando Show Vlan sh vlan VLAN Name Status Ports default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Fa0/24 Gig1/1, Gig1/ fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans enet fddi tr fdnet ieee trnet ibm Remote SPAN VLANs Primary Secondary Type Ports Criando uma Vlan conf t SALESIANO (config)#vlan 10 SALESIANO (config-vlan)#name TESTE SALESIANO (config-vlan)#^z 3
4 6. Verificando a Vlan Criada sh vlan VLAN Name Status Ports default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Fa0/24 Gig1/1, Gig1/2 10 TESTE active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans enet enet fddi tr Inserindo portas à uma Vlan conf t SALESIANO (config)#interface fastethernet 0/20 SALESIANO (config-if)#switchport access vlan 10 SALESIANO (config-if)#no shut SALESIANO (config-if)#^z 4
5 8. Verificando a porta inserida na Vlan show vlan VLAN Name Status Ports default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gig1/1 Gig1/2 10 TESTE active Fa0/ fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup 9. Inserindo IP em uma Vlan SALESIANO >ena conf t SALESIANO (config)#interface vlan 10 SALESIANO (config-if)# %LINK-5-CHANGED: Interface Vlan10, changed state to up SALESIANO (config-if)#ip address SALESIANO (config-if)#no shut SALESIANO (config-if)#^z 5
6 10. Verificando o Status de uma Vlan sh interfaces vlan 10 Vlan10 is up, line protocol is down Hardware is CPU Interface, address is ca.4801 (bia ca.4801) Internet address is /8 MTU 1500 bytes, BW Kbit, DLY usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set ARP type: ARPA, ARP Timeout 04:00:00 Last input 21:40:21, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 1682 packets input, bytes, 0 no buffer Received 0 broadcasts (0 IP multicast) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored packets output, 0 bytes, 0 underruns 0 output errors, 23 interface resets 0 output buffer failures, 0 output buffers swapped out 6
Configuring Link Aggregation
10 CHAPTER This chapter describes how to configure link aggregation for the ML-Series cards, both EtherChannel and packet-over-sonet/sdh (POS) channel. For additional information about the Cisco IOS commands
Lab 5.3.5 Configuring Basic Router Settings with the Cisco IOS CLI
Lab 5.3.5 Configuring Basic Router Settings with the Cisco IOS CLI Device Host Name Interface IP Address Subnet Mask R1 R1 Serial 0/0/0 (DCE) 172.17.0.1 255.255.0.0 FastEthernet 0/0 172.16.0.1 255.255.0.0
Configuring the Switch for the Firewall Services Module
CHAPTER 2 Configuring the Switch for the Firewall Services Module This chapter describes how to configure the Catalyst 6500 series switch or the Cisco 7600 series router for use with the FWSM. Before completing
CISCO ROUTERLAR İLE ISDN BRI DATA HABERLEŞMESİ UYGULAMASI
CISCO ROUTERLAR İLE ISDN BRI DATA HABERLEŞMESİ UYGULAMASI Gökhan AKIN İTÜ 2003 TOPOLOJİ: İSTENENLER: 1. Topolojiyi Legacy DDR tekniği ile kurunuz. 2. Aynõ Topolojiyi Dialer Profile tekniğini kullanarak
- Switch Port Configuration -
1 Cisco Operating Systems - Switch Port Configuration - Cisco offers two brands of network switches: Catalyst Cisco s flagship switching platform, with a large selection of models spanning access, distribution,
Configuring InterVLAN Routing and ISL/802.1Q Trunking on Catalyst 2900XL/3500XL/2940/2950/2970 Series Switches Using an External Router
Configuring InterVLAN Routing and ISL/802.1Q Trunking on Catalyst 2900XL/3500XL/2940/2950/2970 Series Switches Using an External Router Document ID: 14976 Introduction Before You Begin Conventions Prerequisites
PA-MC-T3 Multi-Channel T3 Synchronous Serial Port Adapter Enhancement
PA-MC-T3 Multi-Channel T3 Synchronous Serial Port Adapter Enhancement This feature module describes the PA-MC-T3 Multi-Channel T3 port adapter (PA-MC-T3 [=]), which can now be configured as either customer
Course "Netzwerke" LAB 2 Basic Router Configuration
Course "Netzwerke" LAB 2 Basic Router Configuration Learning Objectives Review of previously learned skills. Basic IOS Command Line Interface operation. Basic Router configuration. Verification and testing
How To Configure A Cisco Router With A Cio Router
CHAPTER 1 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also
Cisco Quality of Service and DDOS
Cisco Quality of Service and DDOS Engineering Issues for Adaptive Defense Network MITRE 7/25/2001 Contents 1. INTRODUCTION...1 2. TESTBED SETUP...1 3. QUALITY OF SERVICE (QOS) TESTS...3 3.1. FIRST IN,
Analysis of Basic Quality of Service Mechanism for Voice over IP In Hamdard University Network Campus
Analysis of Basic Quality of Service Mechanism for Voice over IP In Hamdard University Network Campus Shahbaz Akhatar Siddiqui Student MS (Telecom) Hamdard University Karachi Junior Lecturer in National
Managing vlan.dat in Cisco Catalyst Switches Running Cisco IOS Software
Managing vlan.dat in Cisco Catalyst Switches Running Cisco IOS Software Document ID: 109304 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions Background Information
section examines how to configure leased lines between two routers using HDLC and PPP.
4357ix.fm Page 620 Thursday, August 25, 2011 11:22 AM This chapter covers the following subjects: Configuring Point-to-Point WANs: This section examines how to configure leased lines between two routers
Configuring the Firewall Management Interface
Configuring the Firewall Management Interface The firewall management interface can be configured under each firewall context to provide a virtualized management interface (see Figure 7). The management
Customer Tool Kit. Recommendations from Choice One Communications
Customer Tool Kit Recommendations from Choice One Communications Jason A. Engh (CCNP, CCDA) Data Level II Network Technician Choice One Communications Date: 12/5/01 1 Customer Tool-Kit for Cisco CPE Routers
- Virtual LANs (VLANs) and VTP -
1 - Virtual LANs (VLANs) and VTP - Collision vs. Broadcast Domains A collision domain is simply defined as any physical segment where a collision can occur. Hubs can only operate at half-duplex, and thus
Fundamentals of Switching
1 CCNA 640-801 Exam Notes - Fundamentals of Switching CCNA 640-801 Exam Notes Fundamentals of Switching 1. LAN Segmentation 1.1 In a collision domain, a frame sent by a device can cause collision with
> Avaya / Cisco Interoperability Technical Configuration Guide. Ethernet Routing Switch
Ethernet Routing Switch IP Phones Engineering > Avaya Data Solutions Document Date: April 6, 2010 Document Number: NN48500-588 Document Version: 2.0 Abstract The purpose of this TCG is to show some of
- QoS and Queuing - Queuing Overview
1 Queuing Overview - QoS and Queuing - A queue is used to store traffic until it can be processed or serialized. Both switch and router interfaces have ingress (inbound) queues and egress (outbound) queues.
CCNA Exploration 4.0.5.0 Routing Protocols and Concepts Student Lab Manual
4.0.5.0 Routing Protocols and Concepts Student Lab Manual This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution
Laboratorio 3 Comunicación sincrónica Vía Satélite
Laboratorio 3 Comunicación sincrónica Vía Satélite Esquema de la Red WAN 192.168.0.0 /30 192.168.0.1 Router 1 Router 2 10.0.1.1 192.168.0.1 10.0.2.1 Ethernet Ethernet 10.0.1.20 LAN 1 10.0.1.0 /24 LAN 2
Chapter 3 Using Maintenance & Troubleshooting Tools & Applications Objectives
Using Maintenance & Troubleshooting Tools & Applications Objectives Describe & utilise Cisco IOS diagnostic tools. Explain the need for specialist tools in the troubleshooting process. Configure software
Basic Wireless Configuration
Basic Wireless Configuration Topology Diagram Learning Objectives Configure options in the Linksys Setup tab. Configure options in the Linksys Wireless tab. Configure options in the Linksys Administration
Configuring a Leased Line
CHAPTER 4 Configuring a Leased Line The configuration in this chapter describes how to configure a Cisco 1700 router for IP and IPX over a synchronous serial line. Before You Begin The configuration in
Troubleshooting Switch Port and Interface Problems
Troubleshooting Switch Port and Interface Problems Document ID: 12027 Contents Introduction Prerequisites Requirements Components Used Conventions Physical Layer Troubleshooting Using the LEDs to Troubleshoot
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNP: Optimizing
Configuring IPsec VPN Fragmentation and MTU
CHAPTER 5 This chapter provides information about configuring IPsec VPN fragmentation and the maximum transmission unit (MTU). It includes the following sections: Understanding IPsec VPN Fragmentation
Cisco DSL Router Configuration and Troubleshooting Guide PPPoA Troubleshooting
Cisco DSL Router Configuration and Troubleshooting Guide PPPoA Troubleshooting Document ID: 71115 Contents Introduction Prerequisites Requirements Components Used Conventions Layer 1 Issues Is the carrier
Configuring POS. POS on the ML-Series Card. ML-Series SONET and SDH Circuit Sizes CHAPTER
5 CHAPTER Configuring POS This chapter describes advanced packet-over-sonet/sdh (POS) interface configuration for the ML-Series card. Basic POS interface configuration is included in Chapter 4, Configuring
IP Addressing and Subnetting. 2002, Cisco Systems, Inc. All rights reserved.
IP Addressing and Subnetting 2002, Cisco Systems, Inc. All rights reserved. 1 Objectives Upon completion, you will be able to: Discuss the Types of Network Addressing Explain the Form of an IP Address
CCNP ROUTE 6.0 Student Lab Manual
CCNP ROUTE 6.0 Student Lab Manual This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors
Troubleshoot VDSL. Contents. Introduction. Document ID: 119009 Contributed by Sunil C, Cisco TAC Engineer. Jun 22, 2015
Troubleshoot VDSL Document ID: 119009 Contributed by Sunil C, Cisco TAC Engineer. Jun 22, 2015 Contents Introduction Prerequisites Requirements Components Used Layer 1 Issues Is the carrier detect (CD)
Laboratorio 4. Comunicación sincrónica Vía Satélite
Laboratorio 4 Comunicación sincrónica Vía Satélite Esquema de la Red WAN 192.168.0.0 /30 192.168.0.1 Router 1 Router 2 10.0.1.1 192.168.0.1 10.0.2.1 Ethernet Ethernet 10.0.1.20 LAN 1 10.0.1.0 /24 LAN 2
Cisco DSL Router Configuration and Troubleshooting Guide PPPoE: DSL Router as a PPPoE Client Troubleshooting
Cisco DSL Router Configuration and Troubleshooting Guide PPPoE: DSL Router as a PPPoE Client Troubleshooting Document ID: 71124 Contents Introduction Prerequisites Requirements Components Used Conventions
Exploring the Enterprise Network Infrastructure
CHAPTER 2 Exploring the Enterprise Network Infrastructure Objectives Upon completion of this chapter, you should be able to answer the following questions: What are the main types of network documentation
CISCO IOS XR. Jeffrey Fry October 2012 FryGuy.Net
CISCO IOS XR Jeffrey Fry October 2012 FryGuy.Net Table of Contents 1. Cisco IOS XR Introduction and Comparison to IOS 2. Cisco IOS XR Prompt and Hostname Differences 3. Basic Configuration Options 4. Configuring
Configure IOS Catalyst Switches to Connect Cisco IP Phones Configuration Example
Configure IOS Catalyst Switches to Connect Cisco IP Phones Configuration Example Document ID: 69632 Introduction Prerequisites Requirements Components Used Conventions Background Information Configure
ProCurve / Cisco Interoperability Guide
ProCurve Networking ProCurve / Cisco Interoperability Guide Introduction... 3 Discovery protocols: LLDP & CDP... 4 VLAN configuration... 7 Introduction... 7 VLAN configuration on Cisco Catalyst... 8 VLAN
Appendix A Remote Network Monitoring
Appendix A Remote Network Monitoring This appendix describes the remote monitoring features available on HP products: Remote Monitoring (RMON) statistics All HP products support RMON statistics on the
Dynamic routing protocols over IPSec tunnels between Palo Alto Networks and Cisco routers
Dynamic routing protocols over IPSec tunnels between Palo Alto Networks and Cisco routers Tech Note PAN-OS 4.1 Revision C 2012, Palo Alto Networks, Inc. www.paloaltonetworks.com Contents Overview... 3
Virtual LAN Security: weaknesses and countermeasures. GIAC Security Essentials Practical Assignment Version 1.4b. Steve A.
Virtual LAN Security: weaknesses and countermeasures GIAC Security Essentials Practical Assignment Version 1.4b by Steve A. Rouiller 1 Abstract Based on Blackhat report [11], we decided to investigate
Embedded Event Manager Commands
This module describes the commands that are used to set the Embedded Event Manager (EEM) operational attributes and monitor EEM operations. The Cisco IOS XR software EEM functions as the central clearing
Chapter 2 Reading Organizer
Chapter 2 Reading Organizer After completion of this chapter, you should be able to: Explain the advantages and disadvantages of static routing Configure initial settings on a Cisco switch Configure switch
Network Troubleshooting and Problem Identification. Brad Hale
Network Troubleshooting and Problem Identification Brad Hale Table of Contents Introduction... 3 Troubleshooting Network Performance Issues... 3 Baseline Network Performance... 3 Collect Network Device
This chapter covers the following topics: ADSL Overview Cisco 6160 DSLAM Overview Cisco 6400 UAC Overview DSL Access Architectures and Protocols
This chapter covers the following topics: ADSL Overview Cisco 6160 DSLAM Overview Cisco 6400 UAC Overview DSL Access Architectures and Protocols C H A P T E R 8 Using DSL to Access a Central Site This
Configuring DHCP Snooping and IP Source Guard
CHAPTER 19 This chapter describes how to configure Dynamic Host Configuration Protocol (DHCP) snooping and IP Source Guard on Catalyst 4500 series switches. It provides guidelines, procedures, and configuration
Configuring EtherChannels
CHAPTER 12 This chapter describes how to configure EtherChannels on the Cisco 7600 series router Layer 2 or Layer 3 LAN ports. For complete syntax and usage information for the commands used in this chapter,
Trinity Feature: T1/E1 Configuration
Trinity Feature: Reference Guide Appendix Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW: www.patton.com Part Number: 07MTRINT1E1-APD, Rev. C Revised:
isco Troubleshooting Input Queue Drops and Output Queue D
isco Troubleshooting Input Queue Drops and Output Queue D Table of Contents Troubleshooting Input Queue Drops and Output Queue Drops..1 Interactive: This document offers customized analysis of your Cisco
LiveAction Application Note
LiveAction Application Note Layer 2 Monitoring and Host Location Using LiveAction to monitor and identify inter-/intra-switch VLAN configurations, and locating workstations within the network infrastructure.
Overview of Access VPNs and Tunneling Technologies
Overview of Access VPNs and Tunneling Technologies Introduction A virtual private network (VPN) is a network that extends remote access to users over a shared infrastructure. VPNs maintain the same security
CCIE R&S Lab Workbook Volume I Version 5.0
Copyright Information, Inc. All rights reserved. The following publication, CCIE R&S Lab Workbook Volume I Version 5.0, was developed by Internetwork Expert, Inc. All rights reserved. No part of this publication
04 Internet Protocol (IP)
SE 4C03 Winter 2007 04 Internet Protocol (IP) William M. Farmer Department of Computing and Software McMaster University 29 January 2007 Internet Protocol (IP) IP provides a connectionless packet delivery
ADMINISTRATION GUIDE Cisco Small Business
ADMINISTRATION GUIDE Cisco Small Business 200 Series Smart Switch Administration Guide Contents Chapter 1: Getting Started 1 Starting the Web-based Switch Configuration Utility 1 Launching the Configuration
Lab: Basic Router Configuration
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Def. Gateway R1 Fa0/0 192.168.1.1 255.255.255.0 N/A S0/0/0 192.168.2.1 255.255.255.0 N/A R2 Fa0/0 192.168.3.1 255.255.255.0 N/A
Cisco CCNA Routing and Switching 200-120. Flash Cards and Exam Practice Pack. Eric Rivard. Cisco Press 800 East 96th Street Indianapolis, IN 46240 USA
Cisco CCNA Routing and Switching 200-120 Flash Cards and Exam Practice Pack Eric Rivard Cisco Press 800 East 96th Street Indianapolis, IN 46240 USA ii Cisco CCNA Routing and Switching 200-120 Flash Cards
Introduction to Routing and Packet Forwarding. Routing Protocols and Concepts Chapter 1
Introduction to Routing and Packet Forwarding Routing Protocols and Concepts Chapter 1 1 1 Objectives Identify a router as a computer with an OS and hardware designed for the routing process. Demonstrate
Basic Router Configuration
CHAPTER 3 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also
How To Switch In Sonicos Enhanced 5.7.7 (Sonicwall) On A 2400Mmi 2400Mm2 (Solarwall Nametra) (Soulwall 2400Mm1) (Network) (
You can read the recommendations in the user, the technical or the installation for SONICWALL SWITCHING NSA 2400MX IN SONICOS ENHANCED 5.7. You'll find the answers to all your questions on the SONICWALL
BLADE PVST+ Spanning Tree and Interoperability with Cisco
BLADE PVST+ Spanning Tree and Interoperability with Cisco Technical Brief Industry-standard PVST+ Spanning Tree Protocol with Cisco interoperability Introduction...1 Spanning Tree Protocol (IEEE 802.1d)...1
Management Software. Web Browser User s Guide AT-S106. For the AT-GS950/48 Gigabit Ethernet Smart Switch. Version 1.0.0. 613-001339 Rev.
Management Software AT-S106 Web Browser User s Guide For the AT-GS950/48 Gigabit Ethernet Smart Switch Version 1.0.0 613-001339 Rev. A Copyright 2010 Allied Telesis, Inc. All rights reserved. No part of
ICND1-100-101 IOS CLI Study Guide (CCENT)
ICND1-100-101 IOS CLI Study Guide (CCENT) Hostname: 2. hostname SW1 SWITCH CONFIGURATION Mgmt IP: 2. interface vlan 1 3. ip address 10.0.0.2 4. no shut Gateway: 2. ip default-gateway 10.0.0.1 Local User/Pwd:
Implementation Note for NetFlow Collectors
This document describes the implementation details for NetFlow collectors for the ASA 5580 adaptive security appliance, and includes the following sections: Event-Driven Data Export Bidirectional Flows
AFDX networks. Computers and Real-Time Group, University of Cantabria
AFDX networks By: J. Javier Gutiérrez (gutierjj@unican.es) Computers and Real-Time Group, University of Cantabria ArtistDesign Workshop on Real-Time System Models for Schedulability Analysis Santander,
Chapter 2 Lab 2-2, EIGRP Load Balancing
Chapter 2 Lab 2-2, EIGRP Load Balancing Topology Objectives Background Review a basic EIGRP configuration. Explore the EIGRP topology table. Identify successors, feasible successors, and feasible distances.
About This Guide. Document Objectives. Audience
About This Guide This preface describes the objectives, audience, organization, and conventions of the Cisco 1600 Series Software Configuration Guide. Cisco documentation and additional literature are
CCT vs. CCENT Skill Set Comparison
Operation of IP Data Networks Recognize the purpose and functions of various network devices such as Routers, Switches, Bridges and Hubs Select the components required to meet a given network specification
NetFlow Subinterface Support
NetFlow Subinterface Support Feature History Release Modification 12.2(14)S This feature was introduced. 12.2(15)T This feature was integrated into Cisco IOS Release 12.2 T. This document describes the
How To Configure InterVLAN Routing on Layer 3 Switches
How To Configure InterVLAN Routing on Layer 3 Switches Document ID: 41860 Contents Introduction Prerequisites Requirements Components Used Conventions Configure InterVLAN Routing Task Step by Step Instructions
Internet Working 5 th lecture. Chair of Communication Systems Department of Applied Sciences University of Freiburg 2004
5 th lecture Chair of Communication Systems Department of Applied Sciences University of Freiburg 2004 1 43 Last lecture Lecture room hopefully all got the message lecture on tuesday and thursday same
AlliedWare Plus Version 2.1.2 AT-9000 Layer 2-4 Gigabit Ethernet EcoSwitches Software Release Notes
4 AlliedWare Plus Version 2.1.2 AT-9000 Layer 2-4 Gigabit Ethernet EcoSwitches Software Release Notes Please read this document before you begin to use the management software. The document has the following
CCBOOTCAMP s Comprehensive ICND2 Study Guide With Sample Questions
CCBOOTCAMP s Comprehensive ICND2 Study Guide With Sample Questions Interconnecting Cisco Networking Devices Part 2 (ICND2) Cisco Exam 640-816 A Unique Study Guide format that compresses important need-to-knowinformation
Configuring Serial Interfaces for E1- and T1-Carrier Lines
5 Configuring Serial Interfaces for E1- and T1-Carrier Lines Contents Using the Serial Module for E1- or T1-Carrier Lines.................. 5-3 Elements of an E1- or T1-Carrier Line..........................
Objectives. The Role of Redundancy in a Switched Network. Layer 2 Loops. Broadcast Storms. More problems with Layer 2 loops
ITE I Chapter 6 2006 Cisco Systems, Inc. All rights reserved. Cisco Public 1 Objectives Implement Spanning Tree Protocols LAN Switching and Wireless Chapter 5 Explain the role of redundancy in a converged
Procedure: You can find the problem sheet on Drive D: of the lab PCs. Part 1: Router & Switch
University of Jordan Faculty of Engineering & Technology Computer Engineering Department Computer Networks Laboratory 907528 Lab. 2 Network Devices & Packet Tracer Objectives 1. To become familiar with
Configuring DHCP Snooping
CHAPTER 19 This chapter describes how to configure Dynamic Host Configuration Protocol (DHCP) snooping on Catalyst 4500 series switches. It provides guidelines, procedures, and configuration examples.
How Much Broadcast and Multicast Traffic Should I Allow in My Network?
PowerConnect Application Note #5 November 2003 How Much Broadcast and Multicast Traffic Should I Allow in My Network? This Application Note relates to the following Dell PowerConnect products: PowerConnect
LAB MANUAL for Computer Network
LAB MANUAL for Computer Network CSE-310 F Computer Network Lab L T P - - 3 Class Work : 25 Marks Exam : 25 MARKS Total : 50 Marks This course provides students with hands on training regarding the design,
Router Lab Reference Guide
Router Lab Reference Guide 1 PURPOSE AND GOALS The routing lab allows testing different IP-related protocols and solutions in a close to live environment. You can learn how to configure Cisco routers and
Troubleshooting IP Access Lists
CHAPTER 21 This chapter describes how to troubleshoot IPv4 and IPv6 access lists (IP-ACLs) created and maintained in the Cisco MDS 9000 Family. It includes the following sections: Overview, page 21-1 Initial
ProSAFE M4100 Managed Switches
Software Administration Manual Software Version 10.0.1 March 2015 202-11161-02 350 East Plumeria Drive San Jose, CA 95134 USA Support Thank you for selecting NETGEAR products. After installing your device,
AT-S60 Version 1.1.4 Management Software for the AT-8400 Series Switch. Software Release Notes
AT-S60 Version 1.1.4 Management Software for the AT-8400 Series Switch Supported Platforms Software Release Notes Please read this document before you begin to use the AT-S60 management software. The AT-S60
Unit of Learning # 2 The Physical Layer. Sergio Guíñez Molinos sguinez@utalca.cl 2-2009
Unit of Learning # 2 The Physical Layer Sergio Guíñez Molinos sguinez@utalca.cl 2-2009 Local Area Network (LAN) Redes de Computadores 2 Historic topologies more used in LAN Ethernet Logical Bus and Physical
Cisco Certified Network Associate Exam. Operation of IP Data Networks. LAN Switching Technologies. IP addressing (IPv4 / IPv6)
Cisco Certified Network Associate Exam Exam Number 200-120 CCNA Associated Certifications CCNA Routing and Switching Operation of IP Data Networks Operation of IP Data Networks Recognize the purpose and
TP-LINK. JetStream 28-Port Gigabit Stackable L3 Managed Switch. Overview. Datasheet T3700G-28TQ. www.tp-link.com
TP-LINK JetStream 28-Port Gigabit Stackable L3 Managed Switch Overview TP-LINK s is an L3 managed switch designed to build a highly accessible, scalable, and robust network. The switch is equipped with
- Hubs vs. Switches vs. Routers -
1 Layered Communication - Hubs vs. Switches vs. Routers - Network communication models are generally organized into layers. The OSI model specifically consists of seven layers, with each layer representing
Lab - Using IOS CLI with Switch MAC Address Tables
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1 255.255.255.0 N/A S1 VLAN 1 192.168.1.11 255.255.255.0 192.168.1.1 S2 VLAN 1 192.168.1.12
TECHNICAL BRIEF. 3Com. NJ205 IntelliJack Switch Management Feature: Virtual LANs and Traffic Prioritization
TECHNICAL BRIEF 3Com NJ205 IntelliJack Switch Management Feature: Virtual LANs and Traffic Prioritization What is a Virtual LAN (VLAN)? A VLAN is a logical subnet grouping that can be assigned to users,
Catalyst Layer 3 Switch for Wake On LAN Support Across VLANs Configuration Example
Catalyst Layer 3 Switch for Wake On LAN Support Across VLANs Configuration Example Document ID: 91672 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information
Routing. Static Routing. Fairness. Adaptive Routing. Shortest Path First. Flooding, Flow routing. Distance Vector
CSPP 57130 Routing Static Routing Fairness Adaptive Routing Shortest Path First Flooding, Flow routing Distance Vector RIP Distance Vector Sometimes called Bellman-FOrd Original Arpanet, DECNet, Novell,
VLAN 802.1Q. 1. VLAN Overview. 1. VLAN Overview. 2. VLAN Trunk. 3. Why use VLANs? 4. LAN to LAN communication. 5. Management port
1. VLAN Overview 2. VLAN Trunk 3. Why use VLANs? 4. LAN to LAN communication 5. Management port 6. Applications 6.1. Application 1 6.2. Application 2 6.3. Application 3 6.4. Application 4 6.5. Application
Configuration Guide. Independent T1 Timing. 6AOSCG0025-29A February 2012
6AOSCG0025-29A February 2012 Configuration Guide This configuration guide describes the feature available on certain NetVanta units. This guide explains the differences in configuration settings on all
The State of OpenFlow: Advice for Those Considering SDN. Steve Wallace Executive Director, InCNTRE SDN Lab Indiana University ssw@iu.
The State of OpenFlow: Advice for Those Considering SDN Steve Wallace Executive Director, InCNTRE SDN Lab Indiana University ssw@iu.edu 2 3 4 SDN is an architecture Separation of Control and Data Planes
How To. Configure Ethernet Protection Switching Ring (EPSR) to Protect a Ring from Loops. Introduction
How To Configure Ethernet Protection Switching Ring (EPSR) to Protect a Ring from Loops Introduction Putting a ring of Ethernet switches at the core of a network is a simple way to increase the network
CORPORATE NETWORKING
CORPORATE NETWORKING C. Pham Université de Pau et des Pays de l Adour Département Informatique http://www.univ-pau.fr/~cpham Congduc.Pham@univ-pau.fr Typical example of Ethernet local networks Mostly based
TP-LINK. 24-Port 10/100Mbps + 4-Port Gigabit L2 Managed Switch. Overview. Datasheet TL-SL5428E. www.tp-link.com
TP-LINK 24-Port 10/100Mbps + 4-Port Gigabit L2 Managed Switch Overview TP-LINK JetStream L2 managed switch provides high performance, enterprise-level QoS, advanced security strategies and rich layer 2
Overview of Routing between Virtual LANs
Overview of Routing between Virtual LANs This chapter provides an overview of virtual LANs (VLANs). It describes the encapsulation protocols used for routing between VLANs and provides some basic information
! encor en etworks TM
! encor en etworks TM Version A, March 2010 2013 Encore Networks, Inc. All rights reserved. Configuring the BANDIT III s T1 E1 Card for a PCM Voice Network The T1 E1 card fits into the expansion slot on
Physical WAN Circuit Types
Physical WAN Circuit Types POTS T3 OC3 OC12 OC48 OC192 Plain Old Telephone notes Service 24 x POTS 28 x 3 x T3 4 x OC3 4 x OC12 4 x OC48 bit rate 64 Kbps 1.544 Mbps 45 Mbps 155 Mbps 622 Mbps 2.5 Gbps 9.6Gbps
Configuring Port Security
CHAPTER 62 This chapter describes how to configure the port security feature. For complete syntax and usage information for the commands used in this chapter, see the Cisco IOS Master List, at this URL: