Homework 5 chapter 28: 2, 7, 31, 43

Similar documents
CHAPTER 28 ELECTRIC CIRCUITS

= (0.400 A) (4.80 V) = 1.92 W = (0.400 A) (7.20 V) = 2.88 W

Chapter 7 Direct-Current Circuits

Circuits. The light bulbs in the circuits below are identical. Which configuration produces more light? (a) circuit I (b) circuit II (c) both the same

Electrical Fundamentals Module 3: Parallel Circuits

13.10: How Series and Parallel Circuits Differ pg. 571

How To Find The Current Of A Circuit

Resistors in Series and Parallel

Eðlisfræði 2, vor 2007

DC Circuits (Combination of resistances)

Chapter 5. Parallel Circuits ISU EE. C.Y. Lee

Fig. 1 Analogue Multimeter Fig.2 Digital Multimeter

Problem Solving 8: RC and LR Circuits

Chapter 7. DC Circuits

Cornerstone Electronics Technology and Robotics I Week 15 Combination Circuits (Series-Parallel Circuits)

Physics 133: tutorial week 4 Ohm s law, electrical power, emf and internal resistance.

Exercises on Voltage, Capacitance and Circuits. A d = ( ) π(0.05)2 = F

Capacitors in Circuits

Series and Parallel Resistive Circuits

Series and Parallel Circuits

AP Physics Electricity and Magnetism #4 Electrical Circuits, Kirchoff s Rules

Last time : energy storage elements capacitor.

The Time Constant of an RC Circuit

AP1 Electricity. 1. A student wearing shoes stands on a tile floor. The students shoes do not fall into the tile floor due to

Student Exploration: Circuits

Parallel and Series Resistors, Kirchoff s Law

Curcuits and Differential Equaitons

2 A bank account for electricity II: flows and taxes

First Order Circuits. EENG223 Circuit Theory I

Example: Determine the power supplied by each of the sources, independent and dependent, in this circuit:

Resistors in Series and Parallel

Preamble. Kirchoff Voltage Law (KVL) Series Resistors. In this section of my lectures we will be. resistor arrangements; series and

PHYSICS 111 LABORATORY Experiment #3 Current, Voltage and Resistance in Series and Parallel Circuits

HOW TO USE MULTIMETER. COMPILE BY: Dzulautotech

Experiment 4 ~ Resistors in Series & Parallel

Physics, Chapter 27: Direct-Current Circuits

ES250: Electrical Science. HW7: Energy Storage Elements

Tristan s Guide to: Solving Parallel Circuits. Version: 1.0 Written in Written By: Tristan Miller Tristan@CatherineNorth.com

Circuit Analysis using the Node and Mesh Methods

Experiment #5, Series and Parallel Circuits, Kirchhoff s Laws

TECH TIP # 37 SOLVING SERIES/PARALLEL CIRCUITS THREE LAWS --- SERIES CIRCUITS LAW # THE SAME CURRENT FLOWS THROUGH ALL PARTS OF THE CIRCUIT

Lecture Notes: ECS 203 Basic Electrical Engineering Semester 1/2010. Dr.Prapun Suksompong 1 June 16, 2010

Series and Parallel Circuits

MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question.

ELECTRICAL CIRCUITS. Electrical Circuits

Kirchhoff's Current Law (KCL)

W03 Analysis of DC Circuits. Yrd. Doç. Dr. Aytaç Gören

Current, Resistance and Electromotive Force. Young and Freedman Chapter 25

Σ I in = Σ I out E = IR 1 + IR 2 FXA 2008 KIRCHHOFF S LAWS 1. Candidates should be able to : LAW 1 (K1)

Nodal and Loop Analysis

Series and Parallel Circuits

Basic Laws Circuit Theorems Methods of Network Analysis Non-Linear Devices and Simulation Models

Experiment 8 Series-Parallel Circuits

SERIES-PARALLEL DC CIRCUITS

Experiment NO.3 Series and parallel connection

Direct-Current Circuits

EXAMPLE 8: An Electrical System (Mechanical-Electrical Analogy)

Analysis of a single-loop circuit using the KVL method

Series and Parallel Resistive Circuits Physics Lab VIII

Resistors in Series and Parallel Circuits

Lab 3 - DC Circuits and Ohm s Law

PROCEDURE: 1. Measure and record the actual values of the four resistors listed in Table 10-1.

Kirchhoff s Laws Physics Lab IX

Tristan s Guide to: Solving Series Circuits. Version: 1.0 Written in Written By: Tristan Miller Tristan@CatherineNorth.com

BJT AC Analysis. by Kenneth A. Kuhn Oct. 20, 2001, rev Aug. 31, 2008

8.2. Solution by Inverse Matrix Method. Introduction. Prerequisites. Learning Outcomes

Chapter 13: Electric Circuits

RLC Resonant Circuits

Solution Derivations for Capa #11

CURRENT ELECTRICITY INTRODUCTION TO RESISTANCE, CAPACITANCE AND INDUCTANCE

3. Solve the equation containing only one variable for that variable.

EDEXCEL NATIONAL CERTIFICATE/DIPLOMA UNIT 67 - FURTHER ELECTRICAL PRINCIPLES NQF LEVEL 3 OUTCOME 1 TUTORIAL 1 - DIRECT CURRENT CIRCUIT THEOREMS

DC mesh current analysis

Energy, Work, and Power

Partial Fractions. p(x) q(x)

Series-Parallel Circuits. Objectives

Chapter 1. Fundamental Electrical Concepts

People s Physics Book

Module 2. DC Circuit. Version 2 EE IIT, Kharagpur

Chapter 12 Driven RLC Circuits

Parallel DC circuits

EE301 Lesson 14 Reading: , , and

2.1 Introduction. 2.2 Terms and definitions

Welcome to this presentation on Driving LEDs Resistors and Linear Drivers, part of OSRAM Opto Semiconductors LED Fundamentals series.

Lab 2: Resistance, Current, and Voltage

Chapter 29 Alternating-Current Circuits

45. The peak value of an alternating current in a 1500-W device is 5.4 A. What is the rms voltage across?

Lab 1: DC Circuits. Student 1, Partner : Student 2, student2@ufl.edu

Basic Op Amp Circuits

Springs and Dampers. MCE371: Vibrations. Prof. Richter. Department of Mechanical Engineering. Handout 2 Fall 2011

Using the Impedance Method

The Membrane Equation

Maximum value. resistance. 1. Connect the Current Probe to Channel 1 and the Differential Voltage Probe to Channel 2 of the interface.

7. What is the current in a circuit if 15 coulombs of electric charge move past a given point in 3 seconds? (1) 5 A (3) 18 A (2) 12 A (4) 45 A

Homework # Physics 2 for Students of Mechanical Engineering

Slide 1 / 26. Inductance by Bryan Pflueger

Method 1: 30x Method 2: 15

Physics 2102 Lecture 19. Physics 2102

Unit: Charge Differentiated Task Light it Up!

Your Comments. This was a very confusing prelecture. Do you think you could go over thoroughly how the LC circuits work qualitatively?

Transcription:

http://iml.umkc.edu/physics/wrobel/phy5/homework.htm Homework 5 chapter 8:, 7, 3, 43

Problem 8. Two.5-V batteries (with their positive terminals in the same direction) are inserted in series into the barrel of a flashlight. One battery has an internal resistance of.55 Ω, the other an internal resistance of.53 Ω. When the switch is closed, a current of 6 ma occurs in the lamp. (a) What is the lamp s resistance? (b) What fraction of the chemical energy transformed appears as internal energy in the batteries? S R ε, r ε, r a) Solution Using Ohm's law, we can relate the potential difference across the light bulb (lamp) with the current in the circuit and the resistance of the lamp. () R V The two batteries connected in series produce that potential difference. The potential differences each battery creates, depend on their electromotive forces and internal resistances. Since the batteries are connected in series the voltage across both batteries is equal to the sum of voltages produced by each battery. () V ( ε r ) + ( ε ) r

We obtained two equations with two unknowns (R,V). The rest is math. Solving by substitution the resistance of the battery is: Solution. ( ε r ) + ( ε r ) ε + ε R r r.5v +.5V.55Ω.53Ω 4.59Ω.6A We could use Kirchhoff's rule for the circuit. Only one equation, with unknown resistance R of the lamp, can be obtained for one loop. ε r + ε r R Hence ε + ε R r r b) Electric power is also dissipated in the batteries due to their internal resistance. (Recall that we can treat the battery like a resistor in series with the ideal source of the electromotive force.) From the scalar properties of power we can find the power dissipated in any subset of the elements in the circuit by adding the power dissipated in the elements. Therefore the fraction of the power dissipated in the batteries is: P + P % P + P + P R r + r r + r.55ω +.53Ω r + r + R r + r + R.55Ω +.53Ω + 4.6Ω 8.6%

Problem 8.7 onsider the circuir shown in Figure P8.9. Find (a) the current in the -Ω resistor and (b) the potential difference between point a and b. Ω 5V a Ω b 5Ω 5Ω 3 Ω 3 4 Solution We could solve this problem "step by step" finding the equivalent resistance of various subsets of the system of resistors leading to the answer from Ohm's law. Let's find the current flowing through the battery by finding the equivalent resistance of all the resistors. The currents in the Ω resistor and the left hand side 5 Ω resistor are equal. These resistors are connected in series. Therefore R & 5 Ω + 5Ω 5Ω These two resistors, the other 5 Ω resistor, and the Ω resistor connected to the high potential terminal of the battery have the

same potentials on their sides, respectively. They are connected in parallel. This system has an equivalent resistance of R 5Ω 5Ω Ω ( &5)&5& + +.94Ω The current flowing through the Ω resistor connected to the lower potential terminal of the battery is equal to the current flowing through the remaining resistors ( + 3 + 4 ). The resistor is in series with the rest of the system. The equivalent resistance of the entire circuit is therefore R.94Ω + Ω. 94Ω Using Ohm's law, we find the current flowing through the battery and the Ω resistor connected to the lower potential terminal of the battery. ε 5V.93A R.94Ω b) t is easier to first find the potential difference between the two points indicated in the problem. Using Ohm's law, we can find the voltage across the Ω resistor and add the voltage across the battery. V b V a R + ε.93a Ω + 5V 5.68V a) The current flowing through the Ω resistor has the same value as the current flowing through the Ω &5Ω system. These two resistors are connected in series. Therefore Vb V R 5.68V Ω + 5Ω 4 a &5.7A

Solution a) t is easier to use Kirchhoff's rules to write the equations necessary to find any unknown in the circuit. For this circuit we can find three independent equations from the loop rule, and one equation from the junction rule. The four values of the currents can be found from this set of equations. We can assume that their directions are arbitrary but let's make our assignment following our intuition. Using the loop rule for the marked loops and the junction rule for junction A we obtain four equations. - -Ω + Ω + 5Ω + 3 + -Ω -5Ω -5Ω 3 + 3 4 4-5V Since we are interested in current 4, in our solution we will eliminate the other currents. will eliminate them from the fourth equation using the expressions found from the first three equations 3 5 4.53.5 54.5 +.5A.5 4 4 +.5A and obtain an equation for the current in the Ω resistor (.5 Ω +.5 Ω + 5 Ω + Ω ) 4.5V

Therefore.5V 4.7A.5Ω +.5Ω + 5Ω + Ω omment. Solving linear equations with a large number of unknowns is rather a tedious process. Scientific calculators are equipped with appropriate programs to help with these tasks. Learn how to do it on your calculator. n case your calculator does not have this program, learn a more efficient method than by substitution. Below included a solution using ramer s method D + 5 5 5 + ( ) 5 5 ( ) 5 ( 5 + ( 5) ( 5) + 5 ( 5) ( 5) ) + ( 5 + ( 5) ( 5) ( ) + ( ) ( ) 5 ( 5) ( 5) ) 55 + 5 5 5 D 4 5 5 5 5 5 + 4 ( ) 5 5 5 ( ) + 3 5 ( 5) 5 D D 5 55 4 4.7A

Problem 8.3 The circuit in Figure P8.37 has been connected for a long time. (a) What is the voltage across the capacitor? (b) f the battery is disconnected, how long does it take the capacitor to discharge to one tenth of its initial voltage? B Ω 8Ω V A µf Q -Q 3 4Ω 3 Ω D Solution f the battery was connected for a long time, the current "flowing" through the capacitor has a zero value. This information simplifies the equations we can obtain from Kirchhoff's rules. We can immediately assume that the current flowing through the Ω resistor has the same value as the current flowing through the 4Ω resistor. We can reduce the number of junctions we have to consider. (Notice that junctions A and generate trivial equations.) ( + 4) Ω V (loop ) Ω 8Ω 3 + V (loop ) V Ω 3 + 4Ω (loop 3) (junction B) 3

We obtained four equations with four unknowns. n fact, the first three equations do not include current through the battery. Therefore the first three equations are necessary to find the answer. From the first equation we can find one unknown V A Ω + 4Ω From the second equation Ω + V 3 8Ω Substituting this expression we find the voltage across the capacitor V 3Ω 6V Solution. n this particular case there is a simpler solution. Notice that when the capacitor is "fully" charged (only then), the Ω and 4Ω are connected in series. We can relate the potential at junction B with the potential at junction A. V VA VD 4Ω 4Ω 8V 4Ω + Ω Similarly V V VD 3 Ω Ω V Ω + 8Ω Therefore V V V V V V 6 ( ) ( ) V A A D D

b) When the battery is disconnected, the capacitor is discharged through the system of resistors. A current of the same value will be flowing through the Ω and the 8Ω resistors. They are connected in series. Similarly, we can see that the 4Ω and Ω resistors are connected in series. Both pairs are V dq dv dt dt connected in parallel at points A and. The equivalent resistance of the system is therefore: () R + 3.6Ω Ω + 8Ω 4Ω + Ω The loop rule applied to the equivalent circuit presented in the figure relates the rate of change in the voltage across the capacitor with the value of that voltage at any instant. dv () V R dt We obtained a differential equation for function V (t). hoosing the instant when the battery is disconnected as the reference instant t s, we can express explicitly the time dependence of the voltage across the capacitor. dv V R dt Q -Q R

ln V V V V () t ( ) t R t t () t V ( ) e R From this function we can write an equation for the time t at which the voltage discharges to a given value. t V ( ) V ( ) e R The solution to this equation is: t Rln 3.6Ω µ F ln 8.9µ s

Problem 8.43 alculate the potential difference between points a and b in Figure P8.54, and identify which point is at the higher potential. 4V Ω a Using Kirchhoff's rules we can write three independent equations for this circuit. V 4Ω Although since points a and b are not connected, we can immediately predict that the Ω current does not flow in the b 4V battery and the Ω resistor. The junction rule, therefore, implicates the same value for the current in the other two resistors. For simplicity's sake will skip the units but first made sure all the quantities are expressed in the S unit system. onsistent with the markings in the figure my equations are as follows. : V Ω 4Ω (loop ) 4 Ω 4V ( Va Vb ) + Ω (loop ) ( + (top junction)) Substituting for the current in the second equation, the potential difference between point a and b is V 6Ω ( V V ) 4Ω 4V 4Ω 4V 4V a b The result indicates that the potential at point a is higher.