Installation manual: CADDY Parrot MKi + Parrot CK3100 range CADDY This The VOLKSWAGEN sheet is designed CADDY to marque help you and with VOLKSWAGEN the installation logo of are a the Parrot property product of the and VOLKSWAGEN is purely for France information. Group s.a Any or installation VOLKSWAGEN performed AG. This in compliance document is with only the valid instructions for the vehicle appearing model in CADDY this document year 2011 is AND done 2012, under excluding the sole all responsibility other models of in the installer, same range who and is entirely excluding responsible later for modifications the quality made of the to installation. the vehicle All by rights the manufacturer. reserved Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation The Parrot brand of Parrot name SA. and Pictures logos are for the information exclusive property only. of Parrot SA.
Fitting time / Main features Disassembly 30 min NO ACC wire Kit installation 30 min NO ISO Refitting 30 min YES UNIKA Testing 15 min FRONT SPEAKER TEL mode Total 1 hour 45 minutes ALL MUSIC mode CK range Tools Plastic Trim Removal tools FACOM / BOJO MKi range Accessories required -TORX screwdriver - Cutting pliers - Crimping pliers - Multimeter or Test lamp - Pull through cord - Electrical/amalgamation tape - Soldering Iron Kram ref. Dealer ref. CK range 86 200 YY 138 CABL 1 MKi range 84 942 YY 138 CABL 2 Photos for illustration purposes Updating "Please contact your retailer to purchase accessories. List of retailers available at www.certified.parrot.com" To get the most out of your hands-free kit, we recommend that you update your software regularly. The procedure for doing this can be found at http://www.parrot.com/usa/support/downloads
Disassembly
Disassembly 1 / 3 1 2 1 2 Release the panel by inserting the plastic pry tools underneath Remove screws 1 and 2 3 4 Unclip the cabin light and Using the plastic pry tools, unclip disconnect it the vanity light from the lefthand side 5 6 3 4 4 5 Using the plastic pry tools, unclip the car stereo and air conditioning surround. Remove screws 3, 4, 5 and 6 around the car stereo. Disconnect the connector and the aerial cables
Disassembly 2 / 3 7 8 7 9 9 8 10 Remove screws 7, 8, 9 and 10 around the air conditioning control unit, then remove it without disconnecting it Open the storage compartment under the steering wheel 10 Press down on the tabs inside to release the box Pull up to unclip it 11 12 Using the plastic pry tools, unclip the side panel of the dashboard on the driver's side Unclip the cover plate running up the side of the door
Disassembly 3 / 3 13 Remove the door seal 9 10
Finding an ACC wire 1 2 Using a guide, feed an electric wire from under the steering wheel to the car stereo housing. Feed the wire to the left into the fusebox housing Fit a 1.5 mm connector and insert it into one of the small fuse housings on the left-hand side of the box (using the multimeter, check that the +12 v is connected to the ignition) 3 Reconnect the ACC wire using a round male connector to the blue wire of the adaptor in front of the fuse holder
Microphone feeding 1 / 2 1 2 3 Using a guide, feed the cable from the windscreen to the cabin light After cleaning the centre of the panel where the rain sensor is connected, attach the cradle supplied. 4 Using a guide, feed the cable Using a guide, feed the cable from the cabin light to the vanity from the vanity light to the light driver's side door 5 6 Slide the cable along the driver's side door while refitting the door seal Pass the cable through the fusebox
Microphone feeding 2 / 2 7 8 Using a guide, feed the cable from the top of the dashboard to the fusebox Using a guide, feed the cable under the steering wheel towards the car stereo housing
Feeding the accessory cable 1 2 Using a guide, feed the cable in the top part of the glove compartment through to the air conditioning control unit housing Make sure that the cable is long enough
Fitting the hands-free system 1 / 2 1 Connect the adaptor to the original connector and connect all of the wires to the blue box as shown in the diagram below. Test the assembly before completing fitting and then slide everything behind the air conditioning control unit Direct adaptor cable
2 Fitting the hands-free system 2 / 2! 3 4 Slide the cable behind the air conditioning control unit PLEASE NOTE: When refitting the system, take care not to trap and cut the cable After cleaning the left-hand side of the car stereo/air conditioning surround, affix the mounting (supplied) 12
Testing Before refitting the system, switch the kit on using the ignition (or by starting the car). By pushing the central knob of the remote control, check: 1 - that the menu is displayed on the screen (language or ipod) 2 - that the system can be muted (click in the blue box) 3 - that there is no sound coming from the speakers 4 - that the sound from the voice menu is coming out of the front speakers 5 - then turn off the ignition, check that the kit switches off and that the "goodbye" message appears on the screen (if not, reverse the fuses on the kit's wiring harness) 6 - pair a telephone with the kit and make a call (check that both the microphone and the kit are working)
Refitting Refit the system using the following procedure: 1 - refit the panel next to the dashboard 2 - refit the panel on the left-hand side of the dashboard 3 - refit the storage compartment under the steering wheel 4 - reconnect and refit the cabin light (screws 1 and 2) 5 - refit the cabin light panel 6 - refit the vanity light 7 - refit the 4 screws (7, 8, 9 and 10) for the air conditioning control unit 8 reconnect the adaptor and the aerials behind the car stereo and slip them inside the housing (make sure that you do not trap and cut any screen wires) 9 - refit the 4 screws (3, 4, 5 and 6) for the car stereo 10 - refit the car stereo and air conditioning surround 12 - retest to check that the system is working correctly