Price List 2016 BUILDING, January 2016 Pittsburgh Corning UK Ltd (Building) www.foamglas.co.uk FOAMGLAS PERINSUL HL FOAMGLAS Slabs FOAMGLAS Blocks FOAMGLAS Tapered Slabs and Blocks FOAMGLAS Boards FOAMGLAS PERISAVE FOAMGLAS Accessories
Index FOAMGLAS PERINSUL HL 3 SLABS - FOAMGLAS Slabs 4 - FOAMGLAS READY BLOCK 8 - FOAMGLAS ROOF BLOCK 11 - FOAMGLAS Tapered Slabs 14 - FOAMGLAS Tapered READY BLOCK 15 - FOAMGLAS Tapered ROOF BLOCK 16 BOARDS - FOAMGLAS WALL BOARD 17 - FOAMGLAS FLOOR BOARD 18 - FOAMGLAS READY BOARD 21 - FOAMGLAS ROOF BOARD G2 22 FOAMGLAS PERISAVE 23 FOAMGLAS Accessories 24 Frequently Asked Questions & Further Information 32 General Terms & Conditions of Sale 34
FOAMGLAS PERINSUL HL FOAMGLAS PERINSUL HL Compressive strength at breakpoint 2.9 N/mm 2 Applications: To ensure continuity of the insulation system by eliminating thermal bridging at structural junctions. Technical Data, see European Technical Approval (ETA) and Product Profile literature. Article number Thickness x Width x Length Pieces per pack Linear m per pack Gross kg per pack Price per pack * Thickness = Height mm pcs / pack m / pack kg / pack Price / pack 65 x 100 x 450 25 11.25 13.5 109.83 65 x 140 x 450 17 7.65 12.9 104.59 65 x 215 x 450 12 5.40 15.0 113.42 100 x 100 x 450 15 6.75 12.5 101.47 100 x 140 x 450 10 4.50 11.7 94.84 100 x 215 x 450 7 3.15 18.0 101.73 140 x 140 x 450 6 2.70 12.0 79.67 140 x 215 x 450 5 2.25 15.0 101.96 Typical applications include: Perimeter Insulation to prevent thermal (cold) bridging between structural elements of the Building: example, between concrete structure and brick or block wall, timber wall, door threshold etc. PERINSUL sizes suit popular brick and block dimensions. Use PERINSUL HL DPC may be located above or below the Perinsul HL. Lay PERINSUL into an even bed of wet mortar; butt the PERINSUL up dry end to end. Lay a bed of mortar over the PERINSUL and commence with construction of the wall. For further information on PERINSUL HL see: Constructive Details http://www.constructivedetails.co.uk/ Building Information Modelling, BIM http://www.nationalbimlibrary.com/foamglas/foamglas-perinsul-hl BBA Certificate Contact info@foamglas.co.uk for further information. Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1000 mm x 1450 mm. 65 mm x 100 mm x 450 mm: 21 packs / pallet 65 mm x 140 mm x 450 mm: 21 packs / pallet 65 mm x 215 mm x 450 mm: 18 packs / pallet 100 mm x 100 mm x 450 mm: 21 packs / pallet 100 mm x 140 mm x 450 mm: 21 packs / pallet 100 mm x 215 mm x 450 mm: 21 packs / pallet 140 mm x 140 mm x 450 mm: 21 packs / pallet 140 mm x 215 mm x 450 mm: 18 packs / pallet FOAMGLAS PERINSUL HL Delivery Charges Pack Quantity England & Wales Scotland Delivery Charges Delivery Charges 1 20.59 41.38 2 30.77 51.98 3 41.38 62.59 4 51.98 73.20 5 58.35 79.57 6-19 68.96 90.18 19-20 79.57 100.79 Over 21 Delivery free of charge Delivery free of charge Delivery: Contact FOAMGLAS, Pittsburgh Corning UK, Tel 020 7492 1731 or info@foamglas.co.uk * See: Order Value, Delivery, Conditions of Sale, page 34. 3
FOAMGLAS Slabs FOAMGLAS W+F D = 0.038 W / mk Density: 100 kg /m 3 Technical Data, see TDS or Product Profile literature. Applications: Façades, External and Internal Walls, Cavity Walls, Soffits. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Slabs Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack W+F 05001 50 x 600 x 450 10 5.0 14.0 18.97 2.70 51.22 W+F 06001 60 x 600 x 450 8 6.0 13.5 22.77 2.16 49.18 W+F 07001 70 x 600 x 450 7 7.0 13.7 26.56 1.89 50.20 W+F 08001 80 x 600 x 450 6 8.0 13.5 30.35 1.62 49.17 W+F 09001 90 x 600 x 450 6 9.0 15.1 34.15 1.62 55.32 W+F 10001 100 x 600 x 450 5 10.0 14.0 37.94 1.35 51.22 W+F 11001 110 x 600 x 450 5 11.0 15.4 41.74 1.35 56.35 W+F 12001 120 x 600 x 450 4 12.0 13.5 45.53 1.08 49.17 W+F 13001 130 x 600 x 450 4 13.0 14.5 49.33 1.08 53.28 W+F 14001 140 x 600 x 450 4 14.0 15.6 53.12 1.08 57.37 W+F 15001 150 x 600 x 450 3 15.0 12.7 56.91 0.81 46.10 W+F 16001 160 x 600 x 450 3 16.0 13.5 60.71 0.81 49.18 Weights are net and for guidance only. Pallet: ± 10 kg. 12 packs / pallet. Pallet dimensions approx. 1200 mm x 1100 mm x 1450 mm. * For thickness over 160 mm install as 2 layers, minimum 80 mm per layer. 4
FOAMGLAS Slabs FOAMGLAS T4+ D = 0.041 W / mk Density: ~ 115 kg /m 3 Technical Data, see TDS or Product Profile literature. Applications: Flat and Tapered Roofs. If required, FOAMGLAS can be installed in 2 or more layers. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Slabs Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack T4+ 04001 40 x 600 x 450 12 4.6 15.4 15.18 3.24 49.18 T4+ 05001 50 x 600 x 450 10 5.8 16.0 18.97 2.70 51.22 T4+ 06001 60 x 600 x 450 8 6.9 15.4 22.77 2.16 49.18 T4+ 07001 70 x 600 x 450 7 8.1 15.7 26.56 1.89 50.20 T4+ 08001 80 x 600 x 450 6 9.2 15.4 30.35 1.62 49.17 T4+ 09001 90 x 600 x 450 6 10.4 17.3 34.15 1.62 55.32 T4+ 10001 100 x 600 x 450 5 11.5 16.0 37.94 1.35 51.22 T4+ 11001 110 x 600 x 450 5 12.7 17.6 41.74 1.35 56.35 T4+ 12001 120 x 600 x 450 4 13.8 15.4 45.53 1.08 49.17 T4+ 13001 130 x 600 x 450 4 15.0 16.6 49.33 1.08 53.28 T4+ 14001 140 x 600 x 450 4 16.1 17.9 53.12 1.08 57.37 T4+ 15001 150 x 600 x 450 3 17.3 14.5 56.91 0.81 46.10 T4+ 16001 160 x 600 x 450 3 18.4 15.4 60.71 0.81 49.18 T4+ 17001 170 x 600 x 450 3 19.6 16.3 64.50 0.81 52.25 T4+ 18001 180 x 600 x 450 3 20.7 17.3 68.30 0.81 55.32 Weights are net and for guidance only. Pallet: ± 10 kg. 12 packs / pallet. Pallet dimensions approx. 1200 mm x 1100 mm x 1450 mm. * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 5
FOAMGLAS Slabs FOAMGLAS S3 D = 0.045 W / mk Density: ~ 135 kg /m 3 Technical Data, see TDS or Product Profile literature. Applications: Flat and Tapered Roofs, which require insulation with a higher compressive strength. If required, FOAMGLAS can be installed in 2 or more layers. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Slabs Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack S3 04001 40 x 600 x 450 12 5.2 17.3 16.46 3.24 53.33 S3 05001 50 x 600 x 450 10 6.5 18.1 20.57 2.70 55.54 S3 06001 60 x 600 x 450 8 7.8 17.3 24.69 2.16 53.33 S3 07001 70 x 600 x 450 7 9.1 17.7 28.80 1.89 54.43 S3 08001 80 x 600 x 450 6 10.4 17.3 32.91 1.62 53.31 S3 09001 90 x 600 x 450 6 11.7 19.5 37.03 1.62 59.99 S3 10001 100 x 600 x 450 5 13.0 18.1 41.14 1.35 55.54 S3 11001 110 x 600 x 450 5 14.3 19.8 45.26 1.35 61.10 S3 12001 120 x 600 x 450 4 15.6 17.3 49.37 1.08 53.32 S3 13001 130 x 600 x 450 4 16.9 18.8 53.49 1.08 57.77 S3 14001 140 x 600 x 450 4 18.2 20.2 57.60 1.08 62.21 S3 15001 150 x 600 x 450 3 19.5 16.3 61.71 0.81 49.99 S3 16001 160 x 600 x 450 3 20.8 17.3 65.83 0.81 53.32 S3 17001 170 x 600 x 450 3 22.1 18.4 69.94 0.81 56.65 S3 18001 180 x 600 x 450 3 23.4 19.5 74.06 0.81 59.99 Weights are net and for guidance only. Pallet: ± 10 kg. 12 packs / pallet. Pallet dimensions approx. 1200 mm x 1100 mm x 1450 mm. * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 6
FOAMGLAS Slabs FOAMGLAS F D = 0.050 W / mk Density: ~ 165 kg /m 3 Technical Data, see TDS or Product Profile literature. Applications: Flat and Tapered Roofs, which require insulation with the highest compressive strength. If required, FOAMGLAS can be installed in 2 or more layers. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Slabs Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack F 04001 40 x 600 x 450 12 6.6 21.9 20.25 3.24 65.61 F 05001 50 x 600 x 450 10 8.3 22.8 25.31 2.70 68.34 F 06001 60 x 600 x 450 8 9.9 21.9 30.38 2.16 65.62 F 07001 70 x 600 x 450 7 11.6 22.3 35.44 1.89 66.98 F 08001 80 x 600 x 450 6 13.2 21.9 40.50 1.62 65.61 F 09001 90 x 600 x 450 6 14.9 24.6 45.57 1.62 73.82 F 10001 100 x 600 x 450 5 16.5 22.8 50.63 1.35 68.35 F 11001 110 x 600 x 450 5 18.2 25.0 55.69 1.35 75.18 F 12001 120 x 600 x 450 4 19.8 21.9 60.75 1.08 65.61 F 13001 130 x 600 x 450 4 21.5 23.7 65.82 1.08 71.09 F 14001 140 x 600 x 450 4 23.1 25.4 70.88 1.08 76.55 F 15001 150 x 600 x 450 3 24.7 20.5 75.94 0.81 61.51 F 16001 160 x 600 x 450 3 26.4 21.9 81.01 0.81 65.62 Weights are net and for guidance only. Pallet: ± 10 kg. 12 packs / pallet. Pallet dimensions approx. 1200 mm x 1100 mm x 1450 mm. * For thickness over 160 mm install as 2 layers, minimum 80 mm per layer. 7
FOAMGLAS READY BLOCK FOAMGLAS READY BLOCK T4+ D = 0.041 W / mk Density: ~ 115 kg /m 3 Technical Data, see TDS or Product Profile literature. Applications: For Flat and Tapered Roofs. If required, FOAMGLAS can be installed in 2 or more layers, for base layer use Slab T4+. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Blocks Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack RDBLT4+ 04026 40 x 600 x 450 1 4.6 1.4 16.41 0.27 4.43 RDBLT4+ 05026 50 x 600 x 450 1 5.8 1.8 20.51 0.27 5.54 RDBLT4+ 06026 60 x 600 x 450 1 6.9 2.1 24.62 0.27 6.65 RDBLT4+ 07026 70 x 600 x 450 1 8.1 2.4 28.72 0.27 7.75 RDBLT4+ 08026 80 x 600 x 450 1 9.2 2.7 32.82 0.27 8.86 RDBLT4+ 09026 90 x 600 x 450 1 10.4 3.0 36.93 0.27 9.97 RDBLT4+ 10026 100 x 600 x 450 1 11.5 3.3 41.03 0.27 11.08 RDBLT4+ 11026 110 x 600 x 450 1 12.7 3.6 45.13 0.27 12.19 RDBLT4+ 12026 120 x 600 x 450 1 13.8 3.9 49.23 0.27 13.29 RDBLT4+ 13026 130 x 600 x 450 1 15.0 4.2 53.34 0.27 14.40 RDBLT4+ 14026 140 x 600 x 450 1 16.1 4.6 57.44 0.27 15.51 RDBLT4+ 15026 150 x 600 x 450 1 17.3 4.9 61.54 0.27 16.62 RDBLT4+ 16026 160 x 600 x 450 1 18.4 5.2 65.65 0.27 17.73 RDBLT4+ 17026 170 x 600 x 450 1 19.6 5.5 69.75 0.27 18.83 RDBLT4+ 18026 180 x 600 x 450 1 20.7 5.8 73.85 0.27 19.94 Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 32 packs / pallet. * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 8
FOAMGLAS READY BLOCK FOAMGLAS READY BLOCK S3 D = 0.045 W / mk Density: ~ 135 kg /m 3 Technical Data, see TDS or Product Profile literature. Applications: For Flat and Tapered Roofs. If required, FOAMGLAS can be installed in 2 or more layers, for base layer use Slab S3. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Blocks Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack RDBLS3 04026 40 x 600 x 450 1 4.6 1.6 17.69 0.27 4.78 RDBLS3 05026 50 x 600 x 450 1 5.8 2.0 22.11 0.27 5.97 RDBLS3 06026 60 x 600 x 450 1 6.9 2.3 26.54 0.27 7.17 RDBLS3 07026 70 x 600 x 450 1 8.1 2.7 30.96 0.27 8.36 RDBLS3 08026 80 x 600 x 450 1 9.2 3.0 35.38 0.27 9.55 RDBLS3 09026 90 x 600 x 450 1 10.4 3.4 39.81 0.27 10.75 RDBLS3 10026 100 x 600 x 450 1 11.5 3.7 44.23 0.27 11.94 RDBLS3 11026 110 x 600 x 450 1 12.7 4.1 48.65 0.27 13.14 RDBLS3 12026 120 x 600 x 450 1 13.8 4.4 53.07 0.27 14.33 RDBLS3 13026 130 x 600 x 450 1 15.0 4.8 57.50 0.27 15.53 RDBLS3 14026 140 x 600 x 450 1 16.1 5.1 61.92 0.27 16.72 RDBLS3 15026 150 x 600 x 450 1 17.3 5.5 66.34 0.27 17.91 RDBLS3 16026 160 x 600 x 450 1 18.4 5.8 70.77 0.27 19.11 RDBLS3 17026 170 x 600 x 450 1 19.6 6.2 75.19 0.27 20.30 RDBLS3 18026 180 x 600 x 450 1 20.7 6.5 79.61 0.27 21.49 Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 32 packs / pallet. * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 9
FOAMGLAS READY BLOCK FOAMGLAS READY BLOCK F D = 0.050 W / mk Density: ~ 165 kg /m 3 Technical Data, see TDS or Product Profile literature. Applications: For Flat and Tapered Roofs. If required, FOAMGLAS can be installed in 2 or more layers, for base layer use Slab F. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Blocks Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack RDBLF 04026 40 x 600 x 450 1 4.6 2.0 21.49 0.27 5.80 RDBLF 05026 50 x 600 x 450 1 5.8 2.4 26.86 0.27 7.25 RDBLF 06026 60 x 600 x 450 1 6.9 2.9 32.23 0.27 8.70 RDBLF 07026 70 x 600 x 450 1 8.1 3.3 37.60 0.27 10.15 RDBLF 08026 80 x 600 x 450 1 9.2 3.8 42.97 0.27 11.60 RDBLF 09026 90 x 600 x 450 1 10.4 4.2 48.34 0.27 13.05 RDBLF 10026 100 x 600 x 450 1 11.5 4.7 53.71 0.27 14.50 RDBLF 11026 110 x 600 x 450 1 12.7 5.1 59.09 0.27 15.95 RDBLF 12026 120 x 600 x 450 1 13.8 5.6 64.46 0.27 17.40 RDBLF 13026 130 x 600 x 450 1 15.0 6.0 69.83 0.27 18.85 RDBLF 14026 140 x 600 x 450 1 16.1 6.4 75.20 0.27 20.30 RDBLF 15026 150 x 600 x 450 1 17.3 6.9 80.57 0.27 21.75 RDBLF 16026 160 x 600 x 450 1 18.4 7.3 85.94 0.27 23.20 Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 32 packs / pallet. * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 10
FOAMGLAS ROOF BLOCK FOAMGLAS ROOF BLOCK G1 T4+ D = 0.041 W / mk Density: ~ 115 kg /m 3 Technical Data, see TDS. Applications: For Flat and Tapered Roofs. If required, FOAMGLAS can be installed in 2 or more layers, for base layer use Slab T4+. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Blocks Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack RBLG1T4+ 04026 40 x 600 x 450 1 4.6 1.4 16.41 0.27 4.43 RBLG1T4+ 05026 50 x 600 x 450 1 5.8 1.8 20.51 0.27 5.54 RBLG1T4+ 06026 60 x 600 x 450 1 6.9 2.1 24.62 0.27 6.65 RBLG1T4+ 07026 70 x 600 x 450 1 8.1 2.4 28.72 0.27 7.75 RBLG1T4+ 08026 80 x 600 x 450 1 9.2 2.7 32.82 0.27 8.86 RBLG1T4+ 09026 90 x 600 x 450 1 10.4 3.0 36.93 0.27 9.97 RBLG1T4+ 10026 100 x 600 x 450 1 11.5 3.3 41.03 0.27 11.08 RBLG1T4+ 11026 110 x 600 x 450 1 12.7 3.6 45.13 0.27 12.19 RBLG1T4+ 12026 120 x 600 x 450 1 13.8 3.9 49.23 0.27 13.29 RBLG1T4+ 13026 130 x 600 x 450 1 15.0 4.2 53.34 0.27 14.40 RBLG1T4+ 14026 140 x 600 x 450 1 16.1 4.6 57.44 0.27 15.51 RBLG1T4+ 15026 150 x 600 x 450 1 17.3 4.9 61.54 0.27 16.62 RBLG1T4+ 16026 160 x 600 x 450 1 18.4 5.2 65.65 0.27 17.73 RBLG1T4+ 17026 170 x 600 x 450 1 19.6 5.5 69.75 0.27 18.83 RBLG1T4+ 18026 180 x 600 x 450 1 20.7 5.8 73.85 0.27 19.94 Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 32 packs / pallet. Price of FOAMGLAS ROOF BLOCK G1 T4+ is the same price as FOAMGLAS READY BLOCK T4+ * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 11
FOAMGLAS ROOF BLOCK FOAMGLAS ROOF BLOCK G1 S3 D = 0.045 W / mk Density: ~ 135 kg /m 3 Technical Data, see TDS. Applications: For Flat and Tapered Roofs. If required, FOAMGLAS can be installed in 2 or more layers, for base layer use Slab S3. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Blocks Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack RBLG1S3 04026 40 x 600 x 450 1 4.6 1.6 17.69 0.27 4.78 RBLG1S3 05026 50 x 600 x 450 1 5.8 2.0 22.11 0.27 5.97 RBLG1S3 06026 60 x 600 x 450 1 6.9 2.3 26.54 0.27 7.17 RBLG1S3 07026 70 x 600 x 450 1 8.1 2.7 30.96 0.27 8.36 RBLG1S3 08026 80 x 600 x 450 1 9.2 3.0 35.38 0.27 9.55 RBLG1S3 09026 90 x 600 x 450 1 10.4 3.4 39.81 0.27 10.75 RBLG1S3 10026 100 x 600 x 450 1 11.5 3.7 44.23 0.27 11.94 RBLG1S3 11026 110 x 600 x 450 1 12.7 4.1 48.65 0.27 13.14 RBLG1S3 12026 120 x 600 x 450 1 13.8 4.4 53.07 0.27 14.33 RBLG1S3 13026 130 x 600 x 450 1 15.0 4.8 57.50 0.27 15.53 RBLG1S3 14026 140 x 600 x 450 1 16.1 5.1 61.92 0.27 16.72 RBLG1S3 15026 150 x 600 x 450 1 17.3 5.5 66.34 0.27 17.91 RBLG1S3 16026 160 x 600 x 450 1 18.4 5.8 70.77 0.27 19.11 RBLG1S3 17026 170 x 600 x 450 1 19.6 6.2 75.19 0.27 20.30 RBLG1S3 18026 180 x 600 x 450 1 20.7 6.5 79.61 0.27 21.49 Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 32 packs / pallet. Price of FOAMGLAS ROOF BLOCK S3 is the same price as FOAMGLAS READY BLOCK S3 * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 12
FOAMGLAS ROOF BLOCK FOAMGLAS ROOF BLOCK G1 F D = 0.050 W / mk Density: ~ 165 kg /m 3 Technical Data, see TDS. Applications: For Flat and Tapered Roofs. If required, FOAMGLAS can be installed in 2 or more layers, for base layer use Slab F. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Blocks Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack RBLG1F 04026 40 x 600 x 450 1 4.6 2.0 21.49 0.27 5.80 RBLG1F 05026 50 x 600 x 450 1 5.8 2.4 26.86 0.27 7.25 RBLG1F 06026 60 x 600 x 450 1 6.9 2.9 32.23 0.27 8.70 RBLG1F 07026 70 x 600 x 450 1 8.1 3.3 37.60 0.27 10.15 RBLG1F 08026 80 x 600 x 450 1 9.2 3.8 42.97 0.27 11.60 RBLG1F 09026 90 x 600 x 450 1 10.4 4.2 48.34 0.27 13.05 RBLG1F 10026 100 x 600 x 450 1 11.5 4.7 53.71 0.27 14.50 RBLG1F 11026 110 x 600 x 450 1 12.7 5.1 59.09 0.27 15.95 RBLG1F 12026 120 x 600 x 450 1 13.8 5.6 64.46 0.27 17.40 RBG1LF 13026 130 x 600 x 450 1 15.0 6.0 69.83 0.27 18.85 RBLG1F 14026 140 x 600 x 450 1 16.1 6.4 75.20 0.27 20.30 RBLG1F 15026 150 x 600 x 450 1 17.3 6.9 80.57 0.27 21.75 RBLG1F 16026 160 x 600 x 450 1 18.4 7.3 85.94 0.27 23.20 Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 32 packs / pallet. Price of FOAMGLAS ROOF BLOCK F is the same price as FOAMGLAS READY BLOCK F * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 13
TAPERED INSULATION FOAMGLAS FOAMGLAS Tapered Slab Tapered insulation FOAMGLAS Type Slab T4+ D = 0.041 W / mk Density: ~ 115 kg /m 3 Technical Data, see TDS or Product Profile literature. Tapered insulation FOAMGLAS Type Slab S3 D = 0.045 W / mk Density: ~ 135 kg /m 3 Technical Data, see TDS or Product Profile literature. Tapered insulation FOAMGLAS Type Slab F D = 0.050 W / mk Density: ~ 165 kg /m 3 Technical Data, see TDS or Product Profile literature. Factory produced with a Tapered thickness as below: % Slope: 0.55% 1.1% 1.25% 1.7% 2.2% 3.3% 4.4% 5.5% 6.7% Gradient: 1:180 1:90 1:80 1:60 1:45 1:30 1:22.5 1.18 1:15 Angle: 0.32 0.64 0.72 0.96 1.27 1.91 2.55 3.18 3.81 Applications: Tapered Insulation System for Roofs, Balconies, Terraces, Walkways, Vehicle Roadway & Parking. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Contact FOAMGLAS UK for further information regarding pricing**. Contact FOAMGLAS UK for the Tapered Insulation Design Service. * For thickness over 180 mm install as 2 layers. Base layer is Slab T4+. FOAMGLAS Building, Net prices, excluding V.A.T., 2015 14
TAPERED INSULATION FOAMGLAS FOAMGLAS Tapered READY BLOCK T4+ Tapered insulation FOAMGLAS Type READY BLOCK T4+ D = 0.041 W / mk Density: ~ 115 kg /m 3 Technical Data, see TDS or Product Profile literature. Factory produced with a Tapered thickness* as below: % Slope: 0.55% 1.1% 1.25% 1.7% 2.2% 3.3% 4.4% 5.5% 6.7% Gradient: 1:180 1:90 1:80 1:60 1:45 1:30 1:22.5 1.18 1:15 Angle: 0.32 0.64 0.72 0.96 1.27 1.91 2.55 3.18 3.81 Applications: Flat Roofs, Tapered Insulation System, FOAMGLAS READY BLOCK. READY BLOCK is cold bonded with PC adhesive to substructures. Membranes can be torched directly onto the upper surface of the READY BLOCK. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. FOAMGLAS Tapered READY BLOCK S3 Tapered insulation FOAMGLAS Type READY BLOCK S3 D = 0.045 W / mk Density: ~ 135 kg /m 3 Technical Data, see TDS or Product Profile literature. Factory produced with a Tapered thickness* as below: % Slope: 0.55% 1.1% 1.25% 1.7% 2.2% 3.3% 4.4% 5.5% 6.7% Gradient: 1:180 1:90 1:80 1:60 1:45 1:30 1:22.5 1.18 1:15 Angle: 0.32 0.64 0.72 0.96 1.27 1.91 2.55 3.18 3.81 Applications: Flat Roofs, Tapered Insulation System, FOAMGLAS READY BLOCK. READY BLOCK is cold bonded with PC adhesive to substructures. Membranes can be torched directly onto the upper surface of the READY BLOCK. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. FOAMGLAS Tapered READY BLOCK F Tapered insulation FOAMGLAS Type READY BLOCK F D = 0.050 W / mk Density: ~ 165 kg /m 3 Technical Data, see TDS or Product Profile literature. Factory produced with a Tapered thickness* as below: % Slope: 0.55% 1.1% 1.25% 1.7% 2.2% 3.3% 4.4% 5.5% 6.7% Gradient: 1:180 1:90 1:80 1:60 1:45 1:30 1:22.5 1.18 1:15 Angle: 0.32 0.64 0.72 0.96 1.27 1.91 2.55 3.18 3.81 Applications: Flat Roofs, Tapered Insulation System, FOAMGLAS READY BLOCK. READY BLOCK is cold bonded with PC adhesive to substructures. Membranes can be torched directly onto the upper surface of the READY BLOCK. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Contact FOAMGLAS UK for further information regarding pricing**. Contact FOAMGLAS UK for the Tapered Insulation Design Service. * For thickness over 180 mm install as 2 layers. Base layer is Slab T4+. 15
TAPERED INSULATION FOAMGLAS FOAMGLAS Tapered ROOF BLOCK G1 T4+ Tapered insulation FOAMGLAS Type ROOF BLOCK G1 T4+ D = 0.041 W / mk Density: ~ 115 kg /m 3 Technical Data, see TDS or Product Profile literature. Factory produced with a Tapered thickness* as below: % Slope: 0.55% 1.1% 1.25% 1.7% 2.2% 3.3% 4.4% 5.5% 6.7% Gradient: 1:180 1:90 1:80 1:60 1:45 1:30 1:22.5 1.18 1:15 Angle: 0.32 0.64 0.72 0.96 1.27 1.91 2.55 3.18 3.81 Applications: Flat Roofs, Tapered Insulation System, FOAMGLAS Tapered ROOF BLOCK G1 T4+. ROOF BLOCK is cold bonded with PC adhesive to substructures. If required, FOAMGLAS can be installed in 2 or more layers, for base layer use Slab T4+. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 16
FOAMGLAS Boards FOAMGLAS WALL BOARD W+F D = 0.038 W / mk Density: 100 kg /m 3 Technical Data, see pages 30-31 or Product Profile literature. Applications: Façades, Walls and Soffits Internal and External, Walls Above and Below Ground. If required, FOAMGLAS can be installed in 2 or more layers. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article Number Thickness, dimensions * Boards Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack WBW+F 04020 40 x 1200 x 600 6 4.0 23.8 16.41 4.32 70.89 WBW+F 05020 50 x 1200 x 600 5 5.0 23.5 20.51 3.60 73.84 WBW+F 06020 60 x 1200 x 600 4 6.0 21.9 24.62 2.88 70.91 WBW+F 07020 70 x 1200 x 600 4 7.0 24.8 28.72 2.88 82.71 WBW+F 08020 80 x 1200 x 600 3 8.0 20.9 32.82 2.16 70.89 WBW+F 09020 90 x 1200 x 600 3 9.0 23.1 36.93 2.16 79.77 WBW+F 10020 100 x 1200 x 600 3 10.0 25.3 41.03 2.16 88.62 WBW+F 11020 110 x 1200 x 600 2 11.0 18.5 45.13 1.44 64.99 WBW+F 12020 120 x 1200 x 600 2 12.0 20.0 49.23 1.44 70.89 WBW+F 13020 130 x 1200 x 600 2 13.0 21.4 53.34 1.44 76.81 WBW+F 14020 140 x 1200 x 600 2 14.0 22.9 57.44 1.44 82.71 WBW+F 15020 150 x 1200 x 600 2 15.0 24.3 61.54 1.44 88.62 WBW+F 16020 160 x 1200 x 600 2 16.0 25.8 65.65 1.44 94.54 Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 40 mm to 90 mm thickness: 8 packs / pallet. 100 mm and 160 mm thickness: 6 packs / pallet. * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 17
FOAMGLAS Boards FOAMGLAS FLOOR BOARD T4+ D = 0.041 W / mk Density ~ 115 kg /m 3 Technical Data, see pages 30-31 or Product Profile literature. Applications: Typically used internally or externally, above or below the floor structure. If required, FOAMGLAS can be installed in 2 or more layers. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Boards Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack FBT4+ 04020 40 x 1200 x 600 6 4.6 26.4 16.41 4.32 70.89 FBT4+ 05020 50 x 1200 x 600 5 5.8 26.2 20.51 3.60 73.84 FBT4+ 06020 60 x 1200 x 600 4 6.9 24.5 24.62 2.88 70.91 FBT4+ 07020 70 x 1200 x 600 4 8.1 27.8 28.72 2.88 82.71 FBT4+ 08020 80 x 1200 x 600 3 9.2 23.5 32.82 2.16 70.89 FBT4+ 09020 90 x 1200 x 600 3 10.4 26.0 36.93 2.16 79.77 FBT4+ 10020 100 x 1200 x 600 3 11.5 28.5 41.03 2.16 88.62 FBT4+ 11020 110 x 1200 x 600 2 12.7 20.9 45.13 1.44 64.99 FBT4+ 12020 120 x 1200 x 600 2 13.8 22.6 49.23 1.44 70.89 FBT4+ 13020 130 x 1200 x 600 2 15.0 24.2 53.34 1.44 76.81 FBT4+ 14020 140 x 1200 x 600 2 16.1 25.9 57.44 1.44 82.71 FBT4+ 15020 150 x 1200 x 600 2 17.3 27.6 61.54 1.44 88.62 FBT4+ 16020 160 x 1200 x 600 2 18.4 29.2 65.65 1.44 94.54 FBT4+ 17020 170 x 1200 x 600 1 19.6 15.1 69.75 0.72 50.22 FBT4+ 18020 180 x 1200 x 600 1 20.7 15.9 73.85 0.72 53.17 Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 40 mm to 90 mm thickness: 8 packs / pallet 100 mm and 160 mm thickness: 6 packs / pallet 170 mm and 180 mm thickness: 14 packs / pallet * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 18
FOAMGLAS Boards FOAMGLAS FLOOR BOARD S3 D = 0.045 W / mk Density ~ 135 kg /m 3 Technical Data, see pages 30-31 or Product Profile literature. Applications: Insulation with higher compressive strength. Typically used internally or externally, above or below the floor structure. If required, FOAMGLAS can be installed in 2 or more layers. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Boards Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack FBS3 04020 40 x 1200 x 600 6 5.2 30.0 18.06 4.32 78.02 FBS3 05020 50 x 1200 x 600 5 6.5 31.0 22.57 3.60 81.25 FBS3 06020 60 x 1200 x 600 4 7.8 28.0 27.09 2.88 78.02 FBS3 07020 70 x 1200 x 600 4 9.1 31.0 31.60 2.88 91.01 FBS3 08020 80 x 1200 x 600 3 10.4 27.0 36.11 2.16 78.00 FBS3 09020 90 x 1200 x 600 3 11.7 29.0 40.63 2.16 87.76 FBS3 10020 100 x 1200 x 600 3 13.0 32.0 45.14 2.16 97.50 FBS3 11020 110 x 1200 x 600 3 14.3 23.0 49.66 1.44 71.51 FBS3 12020 120 x 1200 x 600 2 15.6 26.0 54.17 1.44 78.00 FBS3 13020 130 x 1200 x 600 2 16.9 28.0 58.69 1.44 84.51 FBS3 14020 140 x 1200 x 600 2 18.2 30.0 63.20 1.44 91.01 FBS3 15020 150 x 1200 x 600 2 19.5 32.0 67.71 1.44 97.50 FBS3 16020 160 x 1200 x 600 2 20.8 34.0 72.23 1.44 104.01 FBS3 17020 170 x 1200 x 600 1 22.1 18.1 76.74 0.72 55.25 FBS3 18020 180 x 1200 x 600 1 23.4 18.7 81.26 0.72 58.51 Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 40 mm to 90 mm thickness: 8 packs / pallet 100 mm and 160 mm thickness: 6 packs / pallet 170 mm and 180 mm thickness: 14 packs / pallet * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. 19
FOAMGLAS Boards FOAMGLAS FLOOR BOARD F D = 0.050 W / mk Density ~ 165 kg /m 3 Technical Data, see pages 30-31 or Product Profile literature. Applications: Insulation with the highest compressive strength. Typically used internally or externally, above or below the floor structure. If required, FOAMGLAS can be installed in 2 or more layers. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Boards Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack FBF 04020 40 x 1200 x 600 6 6.6 35.0 21.85 4.32 94.39 FBF 05020 50 x 1200 x 600 5 8.3 35.2 27.31 3.60 98.32 FBF 06020 60 x 1200 x 600 4 9.9 33.1 32.78 2.88 94.41 FBF 07020 70 x 1200 x 600 4 11.6 37.9 38.24 2.88 110.13 FBF 08020 80 x 1200 x 600 3 13.2 32.2 43.70 2.16 94.39 FBF 09020 90 x 1200 x 600 3 14.9 35.7 49.17 2.16 106.21 FBF 10020 100 x 1200 x 600 3 16.5 39.3 54.63 2.16 118.00 FBF 11020 110 x 1200 x 600 2 18.2 28.8 60.09 1.44 86.53 FBF 12020 120 x 1200 x 600 2 19.8 31.2 65.55 1.44 94.39 FBF 13020 130 x 1200 x 600 2 21.5 33.6 71.02 1.44 102.27 FBF 14020 140 x 1200 x 600 2 23.1 36.0 76.48 1.44 110.13 FBF 15020 150 x 1200 x 600 2 24.8 38.4 81.94 1.44 117.99 FBF 16020 160 x 1200 x 600 2 26.4 40.7 87.41 1.44 125.87 Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 40 mm to 90 mm thickness: 8 packs / pallet 100 mm and 160 mm thickness: 6 packs / pallet * For thickness over 160 mm install as 2 layers, minimum 80 mm per layer. 20
FOAMGLAS Boards FOAMGLAS READY BOARD T4+ D = 0.041 W / mk Density ~ 115 kg /m 3 Technical Data, see pages 30-31 or Product Profile literature. Applications: Flat Roofs, Pitched and Metal Roofs, External Walls below ground. Torch on membranes can be applied directly to the upper surface of the READY BOARD. If required, FOAMGLAS can be installed in 2 or more layers. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Boards Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack RDBT4+ 04020 40 x 1200 x 600 6 4.6 26.4 16.41 4.32 70.89 RDBT4+ 05020 50 x 1200 x 600 5 5.8 26.2 20.51 3.60 73.84 RDBT4+ 06020 60 x 1200 x 600 4 6.9 24.5 24.62 2.88 70.91 RDBT4+ 07020 70 x 1200 x 600 4 8.1 27.8 28.72 2.88 82.71 RDBT4+ 08020 80 x 1200 x 600 3 9.2 23.5 32.82 2.16 70.89 RDBT4+ 09020 90 x 1200 x 600 3 10.4 26.0 36.93 2.16 79.77 RDBT4+ 10020 100 x 1200 x 600 3 11.5 28.5 41.03 2.16 88.62 RDBT4+ 11020 110 x 1200 x 600 2 12.7 20.9 45.13 1.44 64.99 RDBT4+ 12020 120 x 1200 x 600 2 13.8 22.6 49.23 1.44 70.89 RDBT4+ 13020 130 x 1200 x 600 2 15.0 24.2 53.34 1.44 76.81 RDBT4+ 14020 140 x 1200 x 600 2 16.1 25.9 57.44 1.44 82.71 RDBT4+ 15020 150 x 1200 x 600 2 17.3 27.6 61.54 1.44 88.62 RDBT4+ 16020 160 x 1200 x 600 2 18.4 29.2 65.65 1.44 94.54 RDBT4+ 17020 170 x 1200 x 600 1 19.6 15.1 69.75 0.72 50.22 RDBT4+ 18020 180 x 1200 x 600 1 20.7 15.9 73.85 0.72 53.17 READY BOARD T4+ has a fleece lower side and a bitumen upper side. Where two or more layers are required, use FOAMGLAS ROOF BOARD G2 T4+ as the base layer. Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 40 mm to 90 mm thickness: 8 packs / pallet 100 mm and 160 mm thickness: 6 packs / pallet 170 mm and 180 mm thickness: 14 packs / pallet * For thickness over 180 mm install as 2 layers, minimum 00 mm per layer. 21
FOAMGLAS Boards FOAMGLAS ROOF BOARD G2 T4+ D = 0.041 W / mk Density ~ 115 kg /m 3 Technical Data, see pages 30-31 or Product Profile literature. Applications: Typically for Roofs, and as a Base Layer for READY BOARD T4+, and ROOF BOARD G2 T4+. If required, FOAMGLAS can be installed in 2 or more layers. FOAMGLAS with adhesive sealed joints provides an insulation system and vapour barrier. Article number Thickness, dimensions * Boards Material per only pack Price per m 2 Price per pack ** Gross kg mm kg / m 2 per pack Price / m 2 m 2 / pack Price / pack RBG2T4+ 04020 40 x 1200 x 600 6 4.6 26.4 16.41 4.32 70.89 RBG2T4+ 05020 50 x 1200 x 600 5 5.8 26.2 20.51 3.60 73.84 RBG2T4+ 06020 60 x 1200 x 600 4 6.9 24.5 24.62 2.88 70.91 RBG2T4+ 07020 70 x 1200 x 600 4 8.1 27.8 28.72 2.88 82.71 RBG2T4+ 08020 80 x 1200 x 600 3 9.2 23.5 32.82 2.16 70.89 RBG2T4+ 09020 90 x 1200 x 600 3 10.4 26.0 36.93 2.16 79.77 RBG2T4+ 10020 100 x 1200 x 600 3 11.5 28.5 41.03 2.16 88.62 RBG2T4+ 11020 110 x 1200 x 600 2 12.7 20.9 45.13 1.44 64.99 RBG2T4+ 12020 120 x 1200 x 600 2 13.8 22.6 49.23 1.44 70.89 RBG2T4+ 13020 130 x 1200 x 600 2 15.0 24.2 53.34 1.44 76.81 RBG2T4+ 14020 140 x 1200 x 600 2 16.1 25.9 57.44 1.44 82.71 RBG2T4+ 15020 150 x 1200 x 600 2 17.3 27.6 61.54 1.44 88.62 RBG2T4+ 16020 160 x 1200 x 600 2 18.4 29.2 65.65 1.44 94.54 RBG2T4+ 17020 170 x 1200 x 600 1 19.6 15.1 69.75 0.72 50.22 RBG2T4+ 18020 180 x 1200 x 600 1 20.7 15.9 73.85 0.72 53.17 FOAMGLAS ROOF BOARD G2 T4+ has fleece on both sides. Where two or more layers are required, use FOAMGLAS ROOF BOARD G2 T4+ as the base layer. Weights are net and for guidance only. Pallet: ± 10 kg. Pallet dimensions approx. 1200 mm x 1200 mm x 1450 mm. 40 mm to 90 mm thickness: 8 packs / pallet 100 mm and 160 mm thickness: 6 packs / pallet 170 mm and 180 mm thickness: 14 packs / pallet * For thickness over 180 mm install as 2 layers, minimum 90 mm per layer. For base layer use FOAMGLAS ROOF BOARD G2 T4+. 22
Special products PC PERISAVE Base Block D 0.038 W/(m K) Density: 100 kg/m 3 Compressive strength (EN 826, Annex A) 400 Kpa Technical Data, see Product Profile literature. Applications: Universal base block; meets passive house requirements. System element which meets passive house insulation requirements. Article number Dimensions piece* Thickness x width length Price per mm mm Each PERISS 28001 280 x 450 600 143.64 PC PERISAVE Marginal Stop D 0.038 W/(m K) Density: 100 kg/m 3 Compressive strength (EN 826, Annex A) 400 Kpa Technical Data, see Product Profile literature. Applications: Marginal stop, insulation and formwork for concrete floor slabs. System element which meets passive house insulation requirements. 15 15 15 Article number Dimensions Price per piece * thickness x width length mm mm Each PERISMS 2502 250 x 300 600 41.91 PERISMS 3002 300 x 300 600 44.34 * See: Order Value, Delivery, Conditions of Sale, page 34. 23
FOAMGLAS Accessory Prices Primer / Adhesives PC EM Primer Type: Viscous, solvent-free bitumen emulsion. Application: Primer coat to improve adhesion on absorbing substructures as concrete, brickwalls and plaster. Consistency: Liquid Colour: Black Solvents: None Mixing ratio: Used as a primer in cold bitumen applications. Dilute the product 1 : 10 (by volume) with water, (1 part PC EM, 10 parts of water). The base surface should be free of dust and form oil (release agents). PC EM can be applied to a dry or wet surface. Working temperature (air + base surface) : +5 C Drying time: App. 3 to 12 hours depending on temperature and humidity. Storage*: Maximum 1 year. Store dry in well-closed containers. Protect against frost, heat and direct sun exposure. Consumption: About 300 g/m 2 finished mixture. Article number Packing unit, pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0004 5 kg 96 pails 12.46 PC 56 Type: Two-component adhesive, hydraulic binding. Application: Bonding of FOAMGLAS slabs / boards to absorbent surfaces. Adhesion of FOAMGLAS slabs to each other. Surfacer. Consistency: Pasty Colour: Black-brown Solvents: None Mixing ration: Fluid / Powder 3 : 1 by weight. The batch supplies the correct proportional quantities of the two components which should be stirred with a power drill and a mixing paddle to a homogeneous adhesive compound until smooth. Working temperature (air + base surface) : +5 C to +35 C Installation: The base surface should be clean and free of dust, it can be dry or wet. The adhesive is applied to the FOAMGLAS elements to be bonded using a notched trowel (depth of notches 8-10 mm). Working time: At +20 C about 90 minutes Curing time: Several days (1 3 days, depending on temperature, humidity and base surface). Storage*: See label for expiration date. Store dry in well-closed containers. Protect against frost, heat and direct sun exposure. Consumption: Complete bonding with filled joints, about 3.5 4.5 kg/m 2 depending on base surface. Surfacer, about 1.5 kg/m 2 Article number Packing unit, Combi-pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0056 28 kg 18 pails 55.11 PC 88 Type: Two-component adhesive. Application: Bonding of FOAMGLAS slabs / boards on to absorbent and non-absorbent surfaces. Adhesion of FOAMGLAS slabs to each other. Consistency: Pasty Colour: Black Solvents: Little Mixing ration: 1 tin per pail Working temperature (air + base surface) : +5 C to +35 C Installation: The base surface should be clean and free of dust, it must be dry. The adhesive is applied to the FOAMGLAS elements to be bonded using a notched trowel (depth of notches 8-10 mm). Working time: At +25 C 2 to 2½ hours Curing time: Several days (1 3 days, depending on temperature, humidity and base surface). Storage*: See label for expiration date. Store dry in well-closed containers. Protect against frost, heat and direct sun exposure. Consumption: Complete bonding with filled joints, about 3.5 4.5 kg/m 2 depending on base surface. Article number Packing unit, Component 1 + 2 Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0062 + 0063 16.2 kg (15.1 l) Comp. 1 + 2 36 pails + tins 139.56 PC 0188 + 0065 8.2 kg (7.6 l) Comp. 1 + 2 48 pails + tins 75.14 * In closed original pail. Accessory components are fully compatible with FOAMGLAS material and systems. It is highly recommended to use them in connection with FOAMGLAS insulation to avoid damage. Due to dependence on suppliers and exchange rates price adjustments during the year for Accessories remain reserved on date of shipment. 24
FOAMGLAS Accessory Prices Adhesives PC 58 Type: Two-component adhesive, hydraulic binding Application: Bonding of FOAMGLAS slabs / boards to absorbent surfaces. Surfacer. Consistency: Pasty Colour: Black-brown Solvents: None Working temperature (air + base surface): +5 C to +35 C Mixing ratio: 24 kg black component + 8 kg powder component (batch supplies the correct proportional quantities) Installation: The base surface should be clean, dry and free of dust and oil. Working time: At 20 C: about 90 minutes Curing time: 1 to 3 days Storage*: See label for expiration date. Store dry in well-closed containers. Protect against frost, heat and direct sun exposure. Consumption: Complete bonding, about 5.0 to 7.0 kg/m 2. Surfacer about 2.0 kg/m 2. Article number Packing unit, Combi-pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0058 32 kg 18 pails 68.13 PC 11 Type: Single-component adhesive Application: Bonding of FOAMGLAS slabs / boards on steel deck using a special extrusion pump applicator. Consistency: Pasty Colour: Black Solvents: Few Working temperature (air + base surface): +5 C to +40 C. Installation: PC 11 is a ready for use, solvent-containing and permanently elastic, non-ageing adhesive to be applied on to a clean base surface. Position and alignement of the bonded insulation slabs can be corrected within 5 minutes. Working time: Drying time: Several days Storage*: See label for expiration date. Store dry in well-closed containers. Protect against frost, heat and direct sun exposure. Consumption: 8 adhesive strips per meter: about 1.0 kg/m 2 (700 g/m 2 surface; 300 g/m 2 butt joint). Note: A compressor powered, air operated Pump for PC 11 can be purchased, or rented (deposit payable), see Price List item Tools, PC 0160, page 27. Article number Packing unit, pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0046 28 kg 22 pails 107.78 PC 0047 3 kg sausage 8 pieces 13.07 PC 500 Type: Single-component adhesive Application: Bonding of FOAMGLAS slabs / boards to absorbent surfaces. Consistency: Pasty Colour: Black-brown Solvents: Few (< 6%) Working temperature (air + base surface): +5 C to + 40 C Installation: The base surface should be clean, dry and free of dust and oil. Surfaces contaminated with form oil (release agents) should be cleaned prior to application. A primer, for example PC EM, is to be applied as a bonding agent. Working time: At + 20 C, several days. Drying time: Completely dry after several months. Touch dry: Several hours, rapid hardening due to thixotropic behaviour of the adhesive (= time related decrease of viscosity). Storage*: Maximum 1 year. Store dry in well-closed containers. Protect against frost, heat and direct sun exposure. Keep away from open flames and sparks. Consumption: Full, completely bonded with filled joints, about 5.0 to 7.0 kg/m 2. Bonding of waterproofing membrane, about 2.0 kg/m 2. Surfacer, about 2.0 kg/m 2. Article number Packing unit, pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0059 25 kg 22 pails 61.54 * In closed original pail. Due to dependence on suppliers and exchange rates price adjustments during the year for Accessories remain reserved on date of shipment. 25
FOAMGLAS Accessory Prices Coatings PC 74 A2 Type: Mineral coating composition Application: Non-combutible coating to be reinforced by glass-fibre fabric PC 150 on FOAMGLAS slabs for the insulation of raised access floors. Consistency: Powdery Colour: Light grey Solvents: None Working temperature (air + base surface): +5 ºC to +35 ºC Mixing ration: 5 6 l water for 25 kg PC 74 A2 Installation: The dry powder is mixed with water. PC 74 A2 is trowel-applied to the dry, dust-free FOAMGLAS surface. Irregularities in the FOAMGLAS layer need to be repaired. PC 150 glass-fibre fabric is embedded with 10 cm overlapping and pressed in the wet PC 74 A2 layer; a second coat of PC 74 A2 is to cover the first. The fabric lining is to be covered completely. Working time: About 3 4 hours Drying time: About 24 72 hours depending on building moisture. Completely cured after 72 hours (resistant). Storage: See label for expiration date. Store cool and dry in well-closed original bags. Consumption: About 3.5 kg/m 2 (depending on work surface). Article number Packing unit, bag Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0060 25 kg 42 bags 28.17 PC 164 Type: Thin-bed coating Application: 1. PC 164 basic coating is used with fabric PC 150 on FOAMGLAS slabs for ceilings and walls. After sufficient curing the surface allows to be covered, for example with final rendering PC 78. 2. For bonding of FOAMGLAS W+F façade slabs to absorbent and non-absorbent surfaces. Attachment of FOAMGLAS slabs to each other. It is a ready-for-use product, based on a liquid polymer dispersion with mineral extenders, sands and additives. Consistency: Pasty Colour: White. Solvents: None Working temperature (air + base surface): +5 C to +25 C Installation: Coating: The base surface should be clean, free of dust and stable. The pasty coating is applied to the FOAMGLAS insulation using a stainless steel trowel or a notched trowel (depth of notches min. 5 mm). Tools can be cleaned with water. For a basic coating PC 164 is spread on the dust-free FOAMGLAS surface with a smoothing trowel and levelled. Adhesive: The base surface should be clean, free of dust and stable. Start with stirring of PC 164 and apply it to one short and one long side of the FOAMGLAS slabs (in stack) and to the entire surface of the FOAMGLAS slab, using a notched trowel (depth of notches 6 8 mm). The insuation slab is adhered to the wall by pushing it dia gonally into the open corner. Working time: 15-20 minutes (surface). Drying time: About 3 to 5 days depending on building moisture Storage*: See label for expiration date. Store cool and dry in well-closed container. Protect against frost, heat and direct sun exposure. Consumption: As a coating, about 3.5 kg/m 2. Note: In swimming pools with high relative humidity the additional application of a primer-sealer, for example PC 130, on top of the basic coating PC 164 is strongly recommended. Article number Packing unit, pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0009 25 kg 24 pails 62.84 PC PITTCOTE 404 Type: Highly elastic acrylic latex coating Application: Weather-resistant finish layer. Use with fabric lining PC FABRIC 79P on FOAMGLAS slabs. Consistency: Pasty Colour: Off-white or black Solvents: None Working temperature (air + base surface): At least + 5 C Installation: Coating: The base surface should be dry, clean and free of dust. PITTCOTE 404 is a finish coat which is spread with a stainless steel trowel on to a basic coating, embedding the reinforcement. Tools can be cleaned with water. As a basic coating PC 164 is trowel-applied to the dust-free FOAMGLAS surface and smoothed. Working time: About 3 to 4 hours. Drying time: About 48 hours. Storage*: See label for expiration date. Store cool and dry in well-closed containers. Protect against frost, heat and direct sun exposure. Consumption: About 2.5 to 3.5 kg/m 2. Article number Packing unit, pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0010 WHITE 25 kg 24 pails 191.43 PC 0011 BLACK 25 kg 24 pails 192.49 * In closed original pail. Due to dependence on suppliers and exchange rates price adjustments during the year for Accessories remain reserved on date of shipment. 26
FOAMGLAS Accessory Prices Coatings PC 140 Type: Thin-bed coating composition (processed fine filler based on synthetic dispersion as per DIN 55 945). Area of application: PC 140 is applied with a steel smoothing trowel onto the previously primed surface. Once dry, the prepared surface can be wetted with moisture. Consistency: Pasty Colour: Natural white, matt Solvents: None Working temperature (air + base surface): + 5 ºC to + 35 ºC Installation: Ready-to-use PC 140 fine filler should be well stirred before application. With a more fluid consistency the coating can be sprayed (add max. 5 10 % of water). When the surface begins to dry, it can be smoothed by wetting with a soft cloth or sponge board or when fully dry, the surface may be scrubbed or sanded. Working time: 20 30 minutes Drying time: App. 24-72 hours depending on building moisture. Touch-dry after 20 minutes to a few hours. Storage: Maximum 1 year. Store cool and dry in well-closed containers. Protect against frost, heat and direct exposure to sunrays. Consumption: As coating app. 1.5 kg/m 2 per mm layer density. Article number Packing unit, pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0087 25 kg 24 pails 24.82 PC 310 Type: Solvent-free bonding course. Area of application: PC 310 is a solvent-free, pigmented and quartz sand bonding course on synthetic resin dispersion. It is used as a primary coat and bonding course for structural plaster on base plaster PC 74 A2. Consistency: Liquid Colour: White, matt Solvents: None Working temperature (air + base surface): + 5 ºC to + 35 ºC Working: PC 310 should be well stirred before use and is applied undiluted by paint brush or by roll. To modify the consistency up to 10 % of water can be added. Working time: 20 30 minutes Drying time: At + 20 ºC and 65 % relative humidity, app. 12 hours. Storage: Maximum 1 year. Store cool and dry in well-closed containers. Protect against frost, heat and direct exposure to sunrays. Consumption: App. 250 g/m 2 (as primer). Article number Packing unit, pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0088 25 kg 24 pails 31.07 PC 78 Type: Final rendering, grading 1.0 to 3.0 mm Area of application: Final rendering (abrasion). Copolymer made of vinyl acetate, vinyl chloride and ethyl as well as calcite sands and other auxiliary materials. With different finish treatments individual decorative structures can be achieved. A PC 164 basic coating, embedding PC 150 fabric reinforcement, can be covered after sufficient curing with PC 78 final rendering. Consistency: Pasty Colour: Natural white Solvents: None Working temperature (air + base surface): + 5 C to + 25 C Installation: The base surface should be dry, clean, free of dust, level and stable. PC 78 is applied in a thin layer with a stainless steel trowel and then smoothed by abrasion, vinyl etc.. Tools should be cleaned with water. Working time: 15-20 minutes (surface) Drying time: App. 24-72 hours depending on building moisture. Storage: Maximum 6 months / 1 year. Store cool and dry in well-closed containers. Protect against frost, heat and direct exposure to sunrays. Consumption: Grading 1.0 mm: App. 1.0 1.5 kg/m 2 Grading 1.5 mm: App. 1.7 2.2 kg/m 2 Grading 2.0 mm: App. 2.5 3.2 kg/m 2 Grading 3.0 mm: App. 3.7 4.5 kg/m 2 Article number Packing unit, pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0105 25 kg / grading 1.0 mm 24 pails 41.45 PC 0144 25 kg / grading 1.5 mm 24 pails 39.91 PC 0145 25 kg / grading 2.0 mm 24 pails 65.43 PC 0094 25 kg / grading 3.0 mm 24 pails 70.06 * In closed original pail. Due to dependence on suppliers and exchange rates price adjustments during the year for Accessories remain reserved on date of shipment. 27
FOAMGLAS Accessory Prices Special products PC 600 Green Adhesive Type: Ready-to use single-component adhesive; anhydrous, thixotropic polymer glue, based on natural oils Application: Bonding of FOAMGLAS Slabs, Boards and Blocks to concrete and timber substrates and for the sealing of FOAMGLAS joints Consistency: Pasty Colour: Green Solvents: None Working temperature (air + base surface): +5 C to + 40 C Installation: The base surface should be clean, dry and free of dust and oil. Surfaces contaminated with form oil (release agents) should be cleaned prior to application. Working time: At + 20 C, several days. Drying time: Surface drying time is several hours; depth drying time is several days. Storage*: Store dry in tightly closed containers. Protect against frost, heat and direct sun exposure. Keep away from open flames and sparks. Consumption: Full bonding with sealed joints, approximately 4.0 to 6.0 kg/m 2. Article number Packing unit, pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0197 28 kg 27 pails 137.53 PC 130 Sealing Primer Type: White-pigmented sealing primer based upon a saponification-resistant synthetic resin Application: Used as a ready processed primer for PC 164 and PC 74 A2 prior to applying the render Consistency: Liquid Colour: White, mat Working temperature (air + base surface): +5 C to +30 C. Application: PC 130 should be stirred with a power drill and is brush- or roll-applied undiluted. Working time: 20-30 minutes Drying: 2 4 hours dust dry at 20 C and 50% r.h., after 15 hours ready for coating Storage*: In cool and dry place. Protect against frost, heat, direct sun exposure. Consumption: Approx. 250 ml/m 2 ~ 400 g/m 2 as a primer Article number Packing unit, pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0155 10 kg 24 pails 10 kg 180.94 PC PITTSEAL 444 N - Sealant Type: Single-component sealing compound Application: Sealing of penetrations and connections. Plastic and permanently elastic compound; adheres to steel, concrete, wood, etc. Consistency: Pasty Colour: - Solvents: Few Working temperature (air and base surface): + 10 C to + 25 C Application: The base surface should be dry, clean and free of dust. FOAMGLAS sealant for walls, floors and roofs, NOT for use on soffits / ceilings. For the cartridges use a caulking gun. Drying: No drying; skin formation in 1 to 3 hours. Storage*: See label for expiration date. Store cool and dry in well-closed containers. Protect against frost, heat and direct sun exposure. Keep away from open flames and sparks. Consumption: About 0.25 kg/m. Article number Packing unit, cartridge Units per pallet; pallet size: 120 x 80 cm (12 cartrides per box) Price / unit PC 0003 310 ml cartridge 100 boxes / pallet 4.86 * In closed original pail. Due to dependence on suppliers and exchange rates price adjustments during the year for Accessories remain reserved on date of shipment. 28
FOAMGLAS Accessory Prices Tile cement, Fabric Reinforcement PC 160 Type: Highly flexible special tile cement. Area of application: PC 160 is a highly flexible special tile cement for fabric-reinforced coating on FOAMGLAS slabs as well as final tile bonding on the previously rendered surface. PC 160 meets the requirements of DIN EN 12004 for hydraulic-setting thin-bed cement and dispersion adhesives. After curing the layer is waterproof and frost-resistant; the material is sufficiently flexible to bridge eventual hair cracks in the base coat. Consistency: Pasty / liquid Colour: A: Light grey. B: White Solvents: None Working temperature (air + base surface): + 5 ºC to + 30 ºC Mixing ration: Component A: Sand/cement, 6 parts per weight of cementatious powder and component B: Liquid synthetic resin, 1 part per weight of elasticator to be mixed for about 3 minutes using a power drill (electric mixer) with 300 revolutions per minute (rpm). Cleaning: Immediate cleaning of tools with water. Working time: App. 1 hour Drying time: After app. 48 hours Storage: Maximum 1 year (both components). Store cool and dry in original packaging. Consumption: Depending on type of rendering base, texture properties and type of tool, 3 mm notches, app. 1.4 kg/m 2 4 mm notches, app. 1.9 kg/m 2 5 mm notches, app. 2.5 kg/m 2 6 mm notches, app. 3.2 kg/m 2 Note: DIN 18195-5 specifies that for walls and floors in wet areas damp-proofing/waterproofing has to be provided. See technical bulletin of Fachverband Deutsches Fliesengewerbe (Professional Association of the German Tile Industry), "Recommendations for damp-/waterproofing measures along with wall or floor tiling and panels for interior or exterior use". Article number Packing unit, bag / pail Units per pallet; pallet size: 120 x 80 cm Price / unit PC 0081 25 kg bag / component A 42 bags 38.95 PC 0082 4.2 kg pail / component B TBA 6.50 PC 150 Glass fabric (FABRIC 79G2) Type: Coarse-meshed glass fabric with styrene acrylic Application: Open-mesh, alkali-resistant glass fabric for reinforcement of coating compositions on FOAMGLAS insulation. Working temperature: Min. 0 C Surface: (m 2 per roll) 50 m 2 Roll: 1 m wide, 50 m long Weight: 165 g/m 2 Meshes/dm 2 : 500 Width of mesh: 3.6 x 3.4 mm Thread thickness: 0.4 mm. Tensile strength: Longitudinal (warp): 42 N/mm Tensile strength: Transverse (weft) 38 N/mm Storage: At least 3 years. Store dry. Article number Roll Surface Rolls per pallet Price / unit PC 0039 1 m wide, 50 m long 50 m 2 30 79.06 PC FABRIC 79P Type: Coarse-meshed polyester fabric Application: Open-mesh, alkali-resistant polyester fabric for reinforcement of coating compositions on FOAMGLAS insulation. Working temperature: Min. 0 C Surface: (m 2 per roll) 46 m 2 Roll: 1 m wide, 46 m long Weight: 90 g/m 2 Meshes/dm 2 : 500 Width of mesh: 3.5 x 3.5 mm Thread thickness: 0.6 mm. Tensile strength: Longitudinal (warp): 6.5 N/mm Tensile strength: Transverse (weft) 5.3 N/mm Storage: At least 3 years. Keep in cool, ventilated place. Article number Roll Surface Price / unit PC 0037-79P 1 m wide, 45 m long 45 m 2 170.13 * In closed original pail. Due to dependence on suppliers and exchange rates price adjustments during the year for Accessories remain reserved on date of shipment. 29
FOAMGLAS Accessory Prices Fixing Plates and Insulation Fixings Roofing plates PC SP 150/150 Article number Dimensions, mm Hole, mm Packing unit, Boxes per Price / box box pallet PC 0034, roofing plate 150 x 150 None 50 pcs 40 52.46 PC 0128 P, façade plate 150 x 150 10.2 50 pcs 40 68.88 PC 0123 P, façade plate 150 x 150 14 50 pcs 40 68.89 Weight per box approx 17 kg. Pallet dimensions approx. 1200 mm x 1000 mm x 1350 mm. Roofing plates PC SP 200/200 Approved by the relevant building supervisory approval Nr. Z-14.4-475 Upon request, other types of material for extra charge. Article number Dimensions, mm Hole, mm Packing unit, box Price / box PC 0111, roofing plate 200 x 200 None 100 pcs 128.56 Insulation fixing A-ISOL Type: Polyethylene insulation fixing with coarse threads, flat head, a setting and screw receptacle. A-ISOL, with receptacle for screw 4.5-5.0 mm Ø. Applications: For fastening additional layers of FOAMGLAS on top of the base layer. Installation: Pre-insert Advantages: - No thermal bridges are created. - Possible to join two rigid FOAMGLAS Boards, Slabs or Blocks with A-ISOL. - Fast efficient installation with common tools. - A-ISOL with receptacle for SW 5 bit. Instructions: To be used according to the instructions from FOAMGLAS technical department. The A-ISOL fixing can be screwed with a cordless screw driver / Philipps-tip screwdriver. Consumption: Depending on the application wall / ceiling Packing unit: Box with 50 pieces Storage: Store dry Article number Type Packing unit, box Price / box PC 0173 A-ISOL 50 50 pcs 24.23 PC 0174 A-ISOL 85 50 pcs 36.95 PC 0175 A-ISOL 120 50 pcs 47.17 PC 0176 A-ISOL 155 50 pcs 61.13 Due to dependence on suppliers and exchange rates price adjustments during the year for Accessories remain reserved on date of shipment. 30
FOAMGLAS Accessory Prices Insulation brackets and Tools PC Anchor F, including fixings 9Article number Length of bracket Insulation thickness Packing unit, box Price / box PC 0068 Size 0 20 mm 40 mm 100 pcs / box, including fixings 79.57 PC 0069 Size 1 30 mm 50 90 mm 100 pcs / box, including fixings 95.48 PC 0070 Size 2 60 mm above 90 mm 100 pcs / box, including fixings 105.06 Weight per box approx. 10 kg. Pallet dimensions approx. 1200 mm x 1000 mm x 1350 mm. Type: Mounting bracket in stainless steel Application: Hidden fixing bracket for fixing FOAMGLAS slabs on ceilings and walls. Suitable base surfaces: concrete, masonry, brickwork, blockwork, timber and metal. In case of hollow block bricks or ventialted bricks contact the manufacturer for the recommended fixing technique. Length of bracket: 20 mm / 30 mm / 60 mm Spacing: For walls: 2 brackets / m 2 ; for soffits: 4 brackets / m 2 Packing unit: Box with 100 brackets; supplied with suitable fixings for masonry, concrete, brickwork and blockwork Storage: Store dry. Cold Adhesive Spreader Type: Notched rubber spreader, NOTE broom type handle is not included. Use: For applying PC 500 and PC 58 adhesive to substrate. Article number Packing unit, piece Consumption per m 2 Price / piece PC 0110 PC Spreader TYPE 6 6 kg/m 2 23.60 Compressed Air Operated PC 11 Adhesive Applicator Compressors to be provided by others. The compressor type required is: 10 bar, 145 psi, 24 litre receiver, 220 l/min, 8 cfm. Note: The compressor powered air operated pump for PC 11 can also be rented (deposit of 450 payable). Article number Packing unit, piece Price / unit PC 0160 Pump for 3 kg PC 11 (air operated applicator) 789.33 PC Mix-Spindle Type: Mixing spindle for powder based adhesives, PC 56, PC 58, PC 72A2 etc. Use: To be used with a heavy duty mixing drill, at least 800 rpm. Article number Packing unit, piece Price / unit PC 0154 1 pcs 15.71 PC Sawblade Type: Sawblade made from molybdenum alloyed high-quality, high-speed steel (HSS). Use: Cutting of FOAMGLAS slabs and boards. Article number Packing unit, piece Price / unit PC 0165 1 piece Length / teeth 575/6 22.88 31
Questions & Further Information Frequently Asked Questions & Further Information A Where can I find Technical Information? 1. For FOAMGLAS Technical and Installation Literature, see www.foamglas.co.uk, or email info@foamglas.co.uk 2. For FOAMGLAS Technical and specification information, see www.ribaproductselector.com/foamglas 3. For your local Technical representative, see uk.foamglas.com/en/building/company/contact/contact_us B Pricing Information 1. To download a current price list go to uk.foamglas.com/en/building/quicklinks/price_list/ 2. For Distribution Customers enquiring about distribution terms please contact info@foamglas.co.uk 3. For FOAMGLAS Perinsul HL pricing see PERINSUL HL pricing page 3 4. All prices provided are valid for 30 days unless amended in writing by Pittsburgh Corning UK Ltd. 5. The Company reserves the right to amend prices subject to one month s notice 6. Terms of payment are strictly 30 days net monthly 7. All materials and accessories are available in full pack quantities only C Where to Buy FOAMGLAS & Accessories 1. To download a current price list go to uk.foamglas.com/en/building/quicklinks/price_list/ 2. For a list of our Distributers go to uk.foamglas.com/en/building/company/contact/distributors D Placing Orders 1. For a list of our Distributers go to uk.foamglas.com/en/building/company/contact/distributors 2. Full delivery address, including postcode, contact name and phone number to be provided in writing at time of order 3. Orders are to be sent preferentially to info@foamglas.co.uk or alternatively by fax on +44 (0) 20 7492 1730 4. All materials and accessories are available in full pack quantities only 5. Please ensure that the standard delivery conditions are met before placing an order see below standard delivery conditions E Small Orders 1. For a list of our Distributers go to uk.foamglas.com/en/building/company/contact/distributors 2. Mainland England, Scotland and Wales orders of less than 2,300 (List price excl VAT), a delivery charge of 150.00 Gross shall be charged 3. All materials and accessories are available in full pack quantities only 4. Standard delivery conditions apply. To request special delivery conditions, please email info@foamglas.co.uk F Transportation and Delivery of FOAMGLAS Perinsul HL Materials 1. For PERINSUL HL delivery details and charges see PERINSUL HL pricing page 3 2. For orders over 21 packs, delivery may be on our standard articulated trailer with standard delivery conditions of vehicle. For further information email info@foamglas.co.uk G Standard delivery conditions: Transportation Cost and Destinations 1. Mainland England, Scotland and Wales orders over 2,300 (List price excl VAT) delivery is free of charge 2. Mainland England, Scotland and Wales orders of less than 2,300 (List price excl VAT), a delivery charge of 150.00 Gross shall be charged 3. For deliveries to UK mainland ports VAT is applicable 4. For VAT exempt deliveries outside the UK Mainland, please email info@foamglas.co.uk for further information 5. For N Ireland a delivery surcharge may apply, for further information please email info@foamglas.co.uk 6. For certain Inner City Postcodes, standard Articulated Trailers will be restricted. For further information please email info@foamglas.co.uk 32
Questions & Further Information H Where can I find Technical Information? 1. All Deliveries shall be by standard CURTAIN SIDED ARTICULATED TRAILERS, measuring 16.5m x 2.6 m x 4.1m high, a clear turning area of 20 m x 20 m is required. Articulated Trailers have 52 stackable pallet spaces. Please note that not all pallets are stackable. For further information please email info@foamglas.co.uk 2. All articulated trailer delivery destinations require forklift offloading equipment which is to be provided by others. Should the delivery driver be delayed awaiting offloading; Pittsburgh Corning reserve the right to charge for any additional costs incurred 3. Should the site be unable to accept our standard delivery vehicle, please ensure the insulation distributor can provide local delivery using smaller vehicles 4. Rigid Vehicles are the exception and shall incur an additional freight charge with a delay on lead times. For further information please email info@foamglas.co.uk I Delivery to Inner City Locations 1. For certain Inner City Postcodes, standard Articulated Trailers will be restricted. For further information please email info@foamglas.co.uk 2. Should the site be unable to accept our standard delivery vehicle, please ensure the insulation distributor can provide local delivery using smaller vehicles J Offloading 1. All articulated trailer delivery destinations require forklift offloading equipment which is to be provided by others. Should the delivery driver be delayed awaiting offloading; Pittsburgh Corning reserve the right to charge for any additional costs incurred 2. All offloading equipment and manpower to be provided by others K Storage of Materials and Accessories 1. Insulation materials should not be stacked more than 2 pallets high, accessories and adhesives cannot be stacked 2. All products should securely stored and have protection from the weather 3. Adhesive must be stored at 5 C or above, protected from direct heat and sunlight 4. For Material Safety data sheets please email info@foamglas.co.uk L Order Cancellation, Changes and Returns 1. Cancellations or changes to the Order or Delivery Address must be notified in writing 4 working days before the dispatch date. Pittsburgh Corning reserve the right to charge for any additional costs incurred 2. Only in exceptional circumstances FOAMGLAS Insulation products will be considered for return. See Pittsburgh Corning (United Kingdom) Limited General Terms and Conditions of Sale. Accessories are non-returnable. For a copy of the returns policy please email info@foamglas.co.uk M Availability 1. For FOAMGLAS Perinsul HL: delivery is typically 3-5 working days from receipt of order 2. For UK stock items, delivery is typically 3-5 working days from receipt of order 3. For European stock items, delivery is typically 5-7 working days from receipt of order 4. For products manufactured to order please allow 10-21 working days from receipt of order 5. For Tapered insulation please allow 10-21 working days from receipt of order & design approval 33
General terms and conditions of sale General Terms and Conditions of Sale All sales by Pittsburgh Corning (United Kingdom) Limited ("PC-UK") are governed by these General Terms and Conditions of Sale ("Terms"). The Buyer agrees to be bound by these Terms upon placing an order with PC-UK to the exclusion of any other terms (including any terms or conditions contained in, or referred to in the Buyer s purchase order, confirmation of order or other correspondence, or implied by law, trade custom, practice or course of dealing. 1. Price and Payment: Product prices are as listed in PC-UK s Current Trade Price Ruling for Goods, as amended from time to time at the sole discretion of PC-UK. Prices are primarily stated in British Pounds (Sterling) and do not include any tax or other charge on the production, sale or shipment of the product imposed by any governmental authority ("Tax"). All Tax shall be paid by the Buyer in addition to the prices quoted or invoiced. In the event that PCUK is required to pay any Tax in relation to the supply of the Product to the Buyer, the Buyer shall reimburse PC-UK in full. All orders will be invoiced at the prices in effect at the time of shipment less any applicable discounts. Payment terms are net 30 days with credit approval by PC-UK and payment must be made in the invoice currency charged. In the event of Buyer s failure to pay an invoice by the due date, PC-UK reserves the right to charge interest on such overdue amount at the rate of 2% above the base interest rate of Barclays Bank. All special requirements such as additional inspections, documentation, labelling or request for certification of compliance must be agreed upon by PC-UK when Buyer places the order and may incur additional charges. 2. Order Acceptance: All orders are subject to acceptance by PC-UK. No contract shall exist between Buyer and PCUK unless and until PC-UK issues an Order Acknowledgement. Also, additional written documentation or specifications may be requested before an order is accepted. 3. Shipment: Shipment of Product within the United Kingdom will be DAP (Incoterms 2010) with unloading at buyer s risk unless otherwise stated. All other shipments will be Ex Works Tessenderlo Belgium (Incoterms 2010) unless otherwise stated. Delivery to the first port of shipment shall constitute delivery to the Buyer. Title and property in all Products will remain with PC-UK until PC-UK has received full payment for the relevant Product (including any Tax or late payment interest due). Risk in all Products shall pass to the Buyer on delivery. The Buyer shall at all times following its assumption of risk, at its own expense maintain all proper insurance with a reputable insurer against all risks for the full current replacement value of such Product. The Buyer shall be free to re-sell the Product before title has passes to the Buyer, providing that the proceeds of sale are held on trust for PC-UK (save that the Buyer may deduct and retain any sum by which the proceeds exceed the amount owing to PC-UK). 4. Delivery: Product will be available for shipment based on factory lead times in effect at the time the order is accepted by PC-UK. Delivery of the product must take place with - in two (2) weeks after notification is sent to the Buyer that the Product is available for shipment. If Product does not ship during the two (2) weeks after notification due to a delay by the Buyer, payment for the Product shall become due on the date PC-UK is prepared to make delivery and PC-UK s delivery obligations shall be deemed fulfilled and all risk of loss or damage to such Product shall thereupon pass to Buyer. In the event the Buyer delays delivery and PC-UK, in its sole discretion, agrees to such delay, PC-UK may place such product in storage either at its manufacturing location or at an off-site location. If the Product is stored, all costs incurred by PC-UK in connection with such storage, including, without limitation, costs of preparing Product for storage, placement into storage, handling, storage or, demurrage fees, inspection, preservation and insurance shall be due and payable by Buyer upon receipt by Buyer of the relevant PC-UK invoice therefore. When conditions permit and upon payment of all amounts due hereunder, PC-UK shall arrange, on behalf of Buyer, and at the cost of Buyer, for shipment to a destination mutually acceptable to PC-UK and Buyer. Buyer may not export any Product to any place out side the country of delivery to any other country without first obtaining any necessary export license or approval. Buyer shall in no event export any Product to any person anywhere in the world engaged in the design, development or manufacture of any weapon of mass destruction or delivery system. 5. Shortage or Damage: No claims for shortage in quantity of Product or damage to Product delivered will be considered unless reported to PC-UK within (i) 48 hours in the case of shipments within the United Kingdom and (ii) 14 days in the case of shipments to a destination outside of the United Kingdom. Claims for damaged Product should be made by the Buyer directly to the delivering carrier upon receipt of shipment. Shortages and / or type of damage should be noted on the freight bill and / or bill of lading at the time of delivery and a copy faxed to PC-UK. Status of the seal should also be documented as "intact" or "broken". Shortages for LTL and list shipments must be noted as such on the freight bill at the time of delivery. 6. Returns: The Buyer can only return Product following written authorization from PC-UK. Only standard Insulation Products in an undamaged condition may be returned. Accessories and specially manufactured Insulation Product are non-returnable. All returns must be in accordance with the PC-UK Returns Policy. 7. Cancellation and Changes to Order: The Buyer may cancel its order only upon written notice to and consent of PC-UK. On cancellation of an order, the Buyer shall pay to PC-UK any costs reasonably and properly incurred by PCUK in relation to such cancellation. Buyer may make changes to a product order for standard material only up to 14 days prior to shipment by PC-UK. All orders for Fabricated and Special order materials are only subject to change with the express written permis sion of PC-UK. 8. Limitation of Warranty and Exclusive Remedy: PC-UK warrants only that the product shall conform to PC-UK s published specifications for the Product when shipped to Buyer. PC-UK will replace without charge goods shown by Buyer to be otherwise than as specified. PC-UK s liability is expressly limited to such replacement unless PC-UK, at its sole discretion, elects to issue a credit to Buyer. PC-UK shall have no further liability to the Buyer. If requested by PCUK, Buyer shall return allegedly nonconforming Product to PC-UK s manufacturing location, and if such Product is replaced, PC-UK will pay freight thereon. In no event will credit, adjustment or return of allegedly nonconforming Product be allowed when the Product has been in the possession of Buyer for more than three (3) months from the date of shipment by PC-UK. Except as provided herein, all conditions and warranties whether express or implied by statute, common law or otherwise, as to the quality or fitness for any of the Products or their correspondence with description are hereby excluded to the fullest extent permitted by law. 9. Recalls: In case of critical product faults justifying a recall of the Products, the Buyer is obliged to confer with PCUK to ensure that the Buyer s related actions will harmonize with PC-UK s policy in respect of product recall. The costs reasonably incurred by the Buyer for any such product recall will be reimbursed by PC-UK to the Buyer if PC-UK is liable therefore. The Buyer shall implement and maintain adequate systems and records to ensure full traceability of all batches of Product. 10. Limitation of Liability: PC-UK s liability to the Buyer shall be limited to the price of the Product with respect to which any breach or loss occurs. Neither party shall in any circumstances be liable (in contract, tort, statutory duty, or otherwise and irrespective of any negligence) for any loss of profits, loss of opportunity, or indirect or consequential losses. Any right of action, claim or remedy in tort (including without limitation, breach of statutory duty) that the Buyer may have against PC-UK is excluded to the fullest extent permitted by law. Nothing in these Terms shall limit or exclude liability of either party for (i) death or personal injury resulting from negligence, (ii) fraud or fraudulent misrepresentation, or (iii) breach of the terms implied by section 12 of the Sale of Goods Act 1979. 11. Force Majeure: PC-UK shall not be liable, nor deemed in default hereunder, for any failure or delay in delivering the Product or in the performance of its other obligations to Buyer hereunder, caused by or arising out of (a) compliance in good faith with any applicable law or regulation or judicial claim of whatever nature and whether national, foreign or local (including the European Union); (b) all acts of God (such as, but not limited to, floods, fires, or tornadoes); (c) strikes and other labour trouble; (d) delays or non-performance by suppliers (or other third parties) of raw products, power or other needed supplies or services; (e) delays or non-performance by transporting carriers; and/or (f) any govern - ment action or inaction; or (g) any other cause, contingency, or circumstance not subject to the reasonable control of PC-UK affecting the performance of PC-UK s obligations hereunder. PC-UK shall determine in good faith the extent to which it can reasonably control a cause, contingency, or circumstance affecting its performance obligations. 12. Retention of Title: The risk in the goods shall pass from the seller to the buyer upon delivery of such goods to the buyer. However, notwithstanding delivery and the passing of risk in the goods, title and property in the goods, including full legal and beneficial ownership, shall not pass to the buyer until the seller has received in cash or cleared funds payment in full for all goods delivered to the buyer under this and all other contracts between the seller and the buyer for which payment of the full price of the goods thereunder has not been paid. Payment of the full price of the goods shall include the amount of any interest or other sum payable under the terms of the and all other contracts between the seller and the buyer under which the goods were delivered. 13. Arbitration: The Buyer and PC-UK agrees that any dispute or controversy arising hereunder (including the validity of this provision) that cannot be resolved between them by good faith negotiations shall be finally settled under the Rules of Arbitration of the London Court of International Arbitration by one arbitrator appointed in accordance with said Rules. Any such arbitration proceeding shall take place in London in the English language. 14. General: If any provision of these Terms is held to be unlawful, void, or for any reason unenforceable, then that provision shall be deemed severable from these Terms and shall not affect the validity and enforceability of any remaining provision. Any waiver by PC-UK of a breach of any term or condition of sale shall not constitute a waiver or prejudice PC-UK s right to otherwise subsequently demand strict compliance with that or any other term or condition of this offer of sale. These Terms are subject to change by PC-UK at any time without notice and all product sold by PC-UK is subject to PC-UK s latest published standard terms and conditions of sale. These Terms and each supply of Product by PC-UK to the Buyer and any dispute or claim arising out of or in connection with it or its subject matter of formation (including non-contractual claims) shall be governed by and construed in accordance with English law. These Terms constitute the whole agreement of the Buyer and PC-UK in relation to its subject matter and supersedes any previous agree - ment, representations, warranties or arrangement (whether in writing or oral) between them in relation to that matter. All clerical errors are subject to correction. 34
www.foamglas.co.uk Pittsburgh Corning (UK) Ltd 31 35, Kirby Street, Hatton Garden London, EC1N 8TE Phone +44 (0)20 7492 1731, Fax +44 (0)20 7492 1730 info@foamglas.co.uk Pittsburgh Corning Europe NV Headquarters Europe, Middle East and Africa (EMEA) Albertkade 1, B - 3980 Tessenderlo, Belgium Phone +32 (0)13 661721 www.foamglas.com O-PDF-0-0116 B-UK-en-PRL-0197