Order # - General Layout Step 8..00 0 Plan View 0 3/4 View 0 Page of 3
Order # - General Information Step 8..00 Using Your Setup Instructions The Visionary Designs Setup Instructions are created specifically for your configuration. They are laid out sequentially, including an exploded view of the entire display, and then a logical series of detailed steps to assemble the main structure and components. We encourage you to study the instructions before attempting to assemble your exhibit. Each page reminds you to tighten the setscrews after disassembling your exhibit to prevent loss of the locks and setscrews (see below in RED). This is VERY IMPORTANT. Cleaning and Packing Your Display ) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners. ) When cleaning laminate inserts or countertops, use mild cleansers and a soft material such as cotton. 3) Keep all display components away from extreme heat and long exposure to sunlight to avoid warping and fading. 4) Retain all packing material. It will make re-packing much easier and will reduce the likelihood of shipping damage. The Tool Most Visionary Designs exhibits can be assembled with the supplied Hex Key Tool. Occasionally, a flat head screwdriver may be required. Detail A Typical Connection Typical Connection (cont d) Most horizontal extrusion connections have a patented expandable lock. This lock inserts into the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock and creates a strong positive connection. Detail B Detail C Detail D Setscrews Detail E Numbered Label Horizontal Inline Connection (remove only one setscrew) Base Plate Connection Vertical Connection (remove only two setscrews) When vertical extrusions are packed in portable cases rather than crates or tubs, they must broken down into smaller sections which then require assembly. Each extrusion contains a numbered label which corresponds with setup instructions. The label is located within a groove of the extrusion (when possible). With Visionary Designs the labels contain Black numbers unless otherwise specified. Remove only () setscrew when disassembling. Replace setscrew in extrusion after assembling it. Before packing, replace setscrew in extrusion to avoid losing it. Attach base plate to round or square vertical extrusion using the bolt provided. Be careful not to strip the threads. Remove only () setscrews when disassembling. Replace setscrews in extrusion after assembling it. Before packing, replace setscrews in extrusion to avoid losing them. 0 Page of 3
Order # - XXXXXXXXXXXXXXXXXXXX Step 3/4 3A/4A 3B/4B 3C/4C / / / / 9 h Vertical Extrusion 9 h Vertical Extrusion. w Horizontal Extusion. w Horizontal Extusion 3C ) Connect lower curved extrusions together. ) Connect lower horizontals to the front and back of the lower curved extrusions as shown. 3) Connect upper curved extrusions together. 4) Attach upper curved extrusions between verticals. ) Attach fabric graphics. ) Attach panels. 7) Use stand off caps and barels to connect graphic panel to curved backwall. 8) Attach lights. * Light Connection Attach lights to backwall where desired and tighten in place. Z4 * Attachment SEG Fabric Standoff Barrel Panel Cap 8..00 3B 3A 4C 4B 4A Attach standoff barrels to backwall panel and secure in place. Apply SEG. Secure graphic panels to standoff barrels using screw caps. Step Step 3 Step * * 3 4 * * 0 Page of 3
Order # - XXXXXXXXXXXXXXXXXXXX Step 3 4 7 8 9 38 h x. w Panel 38 h x 4.87 w Door Panel 38 h x. w Panel 38 h x 7.0 w Curved Panel 38 h x 7.0 w Curved Panel Counter 8..00 ) Connect each item together in numberical order. ) Use the Attachment detail to apply the graphic to the the front curved panels. 3) Place the counter on top of the assembled pedestal. When assembled 3 4 Door Attachment 7 9 8 Panel Stand-Off Barrel Screw Cap Screw stand-off barrels into backwall panel. Attach graphic to stand-offs using screw caps. 0 Page of 3
Order # - XXXXXXXXXXXXXXXXXXXX Step 3 8..00 3 4 7 8 9 38 h x 8. w Panel 38 h x 8. w Panel 38 h x 8. w Door Panel 38 h x 8. w Panel ) Connect each panel together in numberical order. ) Unfold counter and place it on top of assembled lower panels. 4 When assembled 3 7 9 8 0 Page 3 of 3