Spacemaster SX Electric Wire Rope Hoists & Options 1 Bulletin: RM-SX-TG-SPEC-2001-8-ENG.doc
Table of Contents 1 PERFORMANCE... 6 1.1 General...6 2 HOIST DUTY SERVICE CLASSIFICATION... 6 2.1 FEM Hoist Duty Service Classification...6 2.2 ASME Hoist Duty Service Classification...7 2.3 Comparison of Hoist Duty Service Classifications...7 3 HOIST FEATURES... 8 3.1 Standard Features...8 4 HOIST CHARACTERISTICS... 9 4.1 Height of Lift and Drum Code...9 4.2 Hoist Speeds...9 4.3 Suspension Type Code...9 4.4 Reeving Code...9 4.5 Rope Type Code...9 4.6 Hoist Duty Rating...9 4.7 Hoist Characteristics Table...10 5 MAIN COMPONENTS - HOIST... 20 6 HOIST MOTOR...20 6.1 Hoist Motor Features...20 6.2 Optional Hoist Motor Features...20 6.3 Ambient Conditions...21 6.4 P-Motors...21 6.5 T-Motors...21 6.6 Motor Temperature Protection...21 6.7 Motor Cooling...21 6.8 Hoist Motor Brake...21 6.9 50 Hertz Hoist Motor Data Two-speed...22 6.10 50 Hertz Hoist Motor Currents Two-speed...24 6.11 60 Hertz Hoist Motor Data Two-speed...26 6.12 60 Hertz Hoist Motor Currents Two-speed...28 6.13 100 Hertz Hoist Motor Data Inverter Motors...30 6.14 120 Hertz Hoist Motor Data-Inverter Motor...31 6.15 Hoist Motor Currents Inverter Motor (100 & 120 Hertz)...32 7 HOIST GEARBOX... 34 7.1 Hoist Gear Reducer...34 7.2 Hoist Gear Lubricant...34 8 ROPE DRUM...35 8.1 Drum Data...35 8.2 Drum Length Code...35 8.3 Rope Clamps...36 8.4 Rope Guide...36 9 REEVING ILLUSTRATION... 38 9.1 Single Reeved...38 9.2 Double Reeved...38 9.3 Rope Anchor...39 10 WIRE ROPE... 40 10.1 Wire Rope Technical Data...40 10.2 Heavy Duty Wire Rope RR09...41 11 BOTTOM BLOCK... 42 11.1 Bottom Block Dimensions...42 11.2 Block Construction...43 11.3 RSN and HBC Hook Dimensions...44 2 RM-SX-TG-SPEC-2001-8-ENG.doc
11.4 DIN Hooks HOK09...44 11.5 Other Hooks HOK07...44 11.6 Ramshorn (twin-points) Hooks HOK03...44 11.7 Sheaves...45 12 HOIST LIMIT SWITCH - STANDARD SETTING... 46 12.1 SX1 Hoist...46 12.2 SX2-SX7 Hoists...47 13 OVERLOAD DEVICE, MECHANICAL (MEC)... 48 14 TROLLEY... 49 14.1 Special Low Headroom Hoist...49 14.2 Low Headroom Hoist...50 14.3 Normal Headroom Hoist...51 14.4 Patented Track Wheel Option TR26...51 14.5 Swivel Trolley for Curved Track...52 14.6 Double Girder Trolley...53 14.7 Trolley Gauge...53 14.8 Cross Mounting Double Girder Hoist...53 15 INVERTER CONTROL... 54 15.1 Infinitely Variable (EP) Speed Control...54 15.2 Multi-step (MS) Speed Control...54 15.3 Dynamic Braking...54 15.4 Factory settings of Inverters...54 16 VARIABLE FREQUENCY DRIVE TYPES... 55 16.1 CMXC AFD...55 16.2 ControlMaster Select VFD...56 16.3 ControlMaster Plus VFD...57 16.4 ControlMaster Elite VFD...58 17 INVERTER TROLLEY SPEEDS... 59 17.1 Low Headroom - Inverter Trolley...59 17.2 Normal Headroom Inverter Trolley...59 17.3 Double Girder - Inverter Trolley...60 18 TWO-SPEED TROLLEY SPEEDS... 60 18.1 Low Headroom Two-speed Trolley...60 18.2 Normal Headroom Two-speed Trolley...61 18.3 Double Girder Two-speed Trolley...61 19 GEK DRIVE... 62 19.1 MF06 Inverter-duty Motor...62 19.2 Compact Brake...62 19.3 MF06 Two-speed Motor...62 19.4 D.C. Brake...62 20 GEK GEAR LUBRICANTS... 63 21 BRIDGE AND TROLLEY MOTOR DATA... 64 21.1 Inverter Duty Motor Data MF06...64 21.2 Inverter Duty Motor Data MF07...65 21.3 Two-speed Motor Data MF06...65 21.4 Two-speed Motor Data MF07...66 21.5 Two-speed Motor Data MF10...66 22 HOIST CONTROLS... 67 22.1 Monorail Package Hoist (Solo Hoist)...67 22.2 Crane Package Hoist...67 22.3 Power Supply and Control Voltage...67 23 HOIST PROTECTION RATING... 67 24 PENDANT... 68 3 RM-SX-TG-SPEC-2001-8-ENG.doc
24.1 Technical Data...68 24.2 Direction Symbols or Labels...68 25 HOIST MONITOR... 69 25.1 Hoist Monitor HS11...69 25.2 Optional Features...70 25.3 Hoist Monitor Select HS12...70 25.4 HoistMonitor Elite HS13...71 25.5 HoistMonitor Plus PE10...71 26 OUTDOOR SERVICE PROTECTION... 72 27 SURFACE TREATMENT... 72 27.1 Hoist & Trolley Color...72 27.2 End Truck Color...73 27.3 Standard Painting Method...73 28 MATERIALS... 74 29 HOIST OPTIONS... 77 29.1 Second Hoist Brake BRA01...77 29.2 Bumper Extensions between Trolleys DES29...77 29.3 Contactor Control, Trolley Two-speed...77 29.4 Control Transformer & Mainline Contactor DES02...77 29.5 Hoist Motor, IP66 Protection HM04...77 29.6 Crank Shaft for Hoist Motor HM11...77 29.7 Derailment Catches for Double Girder Trolleys OTH23...77 29.8 Hoist Drum Brake HS07...77 29.9 Hoist Motor External Fan MOT08...78 29.10 Hoist without Electrical Controls ELE65...78 29.11 Limit Switch, Hoist Operating with Bypass LIM17...79 29.12 Limit Switch, Extra - Level Setting LIM16...80 29.13 Limit Switch, Hook Operated HS22...81 29.14 Limit Switch, Trolley Traveling One-step (Slowdown) LIM13...81 29.15 Limit Switch, Trolley Traveling One-step (Stop) LIM14...81 29.16 Limit Switch, Trolley Traveling Two-step (Slowdown + Stop) - LIM15...81 29.17 Lockable Hook in Bottom Block HOK02...81 29.18 Lug Mount Suspension...81 29.19 Manual Brake Release for Hoist Motor BRA07...81 29.20 Manual Brake Release for Trolley Motor BRA05...81 29.21 Nonstandard Voltage/frequency for Hoist...81 29.22 Rain Cover for Hoist Motor HS04...82 29.23 Rain Cover for Trolley Motor MOT10...82 29.24 Special Paint Thickness PAI03...82 29.25 Stainless Steel Hoist Enclosure, IP66 PAN03...82 29.26 Stainless Steel Hoist Enclosure, IP55 PAN14...82 29.27 Stainless Wire Rope RR08...82 29.28 Standby Heater for Hoist Control Panel PAN02...82 29.29 Standby Heater for Motors MOT03 (hoist) MOT04 (trolley) MOT16 (bridge)...82 29.30 Transformer for Trolley Control ELE68...82 29.31 Trolley Motor, IP66 Protection TM04...82 29.32 Trolley Motor, Thermal Protection TM10...82 29.33 Trolley Rail Gauge, One Step Smaller from Standard PRI06...82 29.34 Trolley Rail Gauge, One Step Larger from Standard PRI07...83 29.35 Trolley Speed, Faster than Standard SPD10...83 29.36 Trolley Speed, Slower than Standard SPD11...83 29.37 Trolley, Double Girder High Connection DES01...83 29.38 Trolley, Double Girder Low Connection DES01...83 29.39 Trolley, Special Flange Width for Low Headroom DIM19...83 29.40 Trolley, Special Flange Width for Normal Headroom DIM20...83 29.41 Multi-hook Leveling HS18...83 4 RM-SX-TG-SPEC-2001-8-ENG.doc
30 HOIST SPEEDS...83 31 QX CRANE PACKAGE... 84 32 BRIDGE PANEL... 84 33 CRANE ELECTRIFICATION PACKAGE... 84 34 BRIDGE PANEL DIMENSIONS... 85 35 LIMIT SWITCH, BRIDGE TRAVEL ONE-STEP (SLOWDOWN) LIM10... 85 36 PLUG CONNECTORS... 86 36.1 Control Plugs...86 36.2 Power Plugs...86 36.3 Plug Kits and Stainless Steel Enclosures...87 37 BRIDGE GIRDER... 87 38 TANDEM HOISTS... 87 39 CRANE OPTIONS... 88 39.1 Anti-collision Device for Crane OTH08...88 39.2 Anti-collision Device for Second Crane BT20...88 39.3 Bumper Extensions between End Trucks DES44...88 39.4 Contactor Control, Bridge Two-speed...88 39.5 Flashing Light for Bridge Traveling ELE20...88 39.6 Horn ELE05...88 39.7 Limit Switch, Bridge Traveling One-step (Stop) LIM11...89 39.8 Limit Switch, Bridge Traveling Two-step (Slowdown + Stop) LIM12...89 39.9 Limit Switch, Hook Operated, Trips Mainline Contactor ELE64...89 39.10 Limit Switch, Trolley Travel, Trips all Trolleys on Bridge ELE63...89 39.11 Load Display HS09...89 39.12 Load Display for Two Hoists on Crane HS10...89 39.13 Longer Chain for Trolley Tow Arm & Festoon...89 39.14 Manual Brake Release for Bridge Motor BRA06...89 39.15 Nonstandard Voltage/frequency for Crane...89 39.16 Pliotex Type Wire Marking ELE48...89 39.17 Provision for Crane Lights (115v, max. 3x400W) ELE70...90 39.18 Provision for Lights on Bridge (as main voltage) ELE62...90 39.19 Rain Cover for Bridge Motor MOT18...90 39.20 Stainless Steel Bridge Control Enclosure, IP66 PAN04...90 39.21 Standby Heater for Bridge Control Panel PAN08...90 39.22 Standby Heater for Pendant Enclosure PEN03...90 39.23 Standby Heater for Bridge Motor MOT17...90 39.24 Thermal Protection for Bridge Motor MOT16...90 39.25 Transformer for Entire Crane ELE67...90 39.26 Transformer for Bridge Control ELE69...90 39.27 Bridge Motor, IP66 Protection BM04...90 40 CONVERSIONS... 91 5 RM-SX-TG-SPEC-2001-8-ENG.doc
1 Performance 1.1 General Hoists are designed for lifting and transporting of materials only. Under no conditions or circumstances are hoists to be used for lifting or transporting of personnel. Spacemaster SX wire rope hoists are designed for indoor use where the ambient temperature between 14 F and 104 F (-10 C and 40 C), and the elevation is less than 3300 ft [1000m], and the relative humidity is less than 90%. When specially equipped, the hoists may be used for outdoor use or in more extreme ambient temperature conditions -4 F to 122 F (-20 C and 50 C) or a higher elevation. The sound intensity level of the hoist in the assumed operating location does not exceed 70dB. 2 Hoist Duty Service Classification 2.1 FEM Hoist Duty Service Classification Service conditions have important influence on the performance of wearing parts of a hoist such as gears, bearings, rope, sheaves, electrical equipment, brake linings, load and lift limit devices, wheels, etc. Careful consideration of the hoist-duty service classifications will enable the user to evaluate the application, and to obtain a hoist designed for optimum performance and minimum maintenance. According to FEM9.511 standard, the hoist-duty service classification can be determined from its 1) load spectrum 2) average daily operating time. 2.1.1 FEM Load Spectrum The load spectrum can be determined from the table below. LIGHT Occasional full loads. Usually light load. Small fixed load. MEDIUM Occasional full loads. Usually light load. Average fixed load. Load % Load % Operating time % Operating time % HEAVY Repetitive full loads. Usually average load. Heavy fixed load. VERY HEAVY Usually almost full loads. Very heavy fixed load. Load % Operating time % Load % Operating time % 6 RM-SX-TG-SPEC-2001-8-ENG.doc
2.1.2 FEM Average Daily Operating Time The average daily operating time of the hoist can be calculated from the running time of the hoisting machinery [hours/day]. 2 H N T t = V 60 H = average hoisting height [m] N = number of work cycles per hour [cycles/h] T = daily working time [h] V = hoisting speed [m/min] 2.1.3 Determining the FEM hoist duty service classification When the load spectrum and the average daily operating time of the hoist are identified, the duty service classification of the hoist is obtained from the table below. Load spectrum LIGHT MEDIUM HEAVY VERY HEAVY Average daily operating time ISO/FEM (hours per day) 0.5 1 2 4 8 16 M3 1Bm M4 1Am M3 1Bm M4 1Am M5 2m M3 1Bm M4 1Am M5 2m M6 3m M4 1Am M5 2m M6 3m M7 4m M5 2m M6 3m M7 4m M6 3m M7 4m 2.2 ASME Hoist Duty Service Classification For information about ASME Hoist Duty Service Classification, reference ASME publication catalog ASME HST-4 (latest edition) for electric wire rope hoists. 2.3 Comparison of Hoist Duty Service Classifications Code 3 4 5 6 ISO M3 M4 M5 M6 FEM 1Bm 1Am 2m 3m ASME HST-4M H2 H3 H4 H4* Starts per Hour FEM 150 180 240 300 360 ASME HST-4M 75 150 300 300 --- FEM Intermittent Duty-ANSI/ASME Uniformly Distributed Work Periods (min/hr) FEM ASME HST-4M 7.5 15 30 30 --- *None of the Spacemaster SX hoists is or can be rated higher than ASME H4 duty service classification. 7 RM-SX-TG-SPEC-2001-8-ENG.doc
3 Hoist Features 3.1 Standard Features Two-speed hoist motor (6:1 ratio) with thermal protection, class F insulation D.C. disc hoist brake Compact hoist gear box Overload limit device Over-travel protection Rope guide **Hoist and trolley controls Inverter trolley control (except SX1 hoist; contactor control) 65 fpm [20 m/min] trolley speed (except SX1 hoist; 80/20 fpm [25/6.3 m/min]) Trolley drive with inverter-duty motor with brake (except SX1; two-speed motor) Crown tread wheels on under-hung trolley suitable for flat or tapered flange Flat tread wheels on double girder trolley Trolley bumper and safety drop lug HBC or RSN style hook with spring-return safety latch IP55 protection for motor Standard hoist nameplate carries a CSA c/us rating and a NEMA 3R rating for electrical enclosures Plugs for power (some exceptions) and controller cables (except SX1 hoist; hardwired) Wiring Diagram Hoist Owner s manual - Paper + CD (1 set) Includes: Hoist (load) test certificate Hook certificate for RSN or HBC hook Wire rope certificate ** For monorail applications, the mainline contactor, control transformer and the pushbutton pendant are available as equipment adders except these items are standard equipment on the SX1 hoist. ** For crane applications, the mainline contactor and control transformer are supplied as standard in the bridge panel. The pushbutton pendant is selected as part of the crane components. 8 RM-SX-TG-SPEC-2001-8-ENG.doc
4 Hoist Characteristics The hoist characteristics table is a summary of the hoist characteristics, which include: Height of lift and corresponding drum (length) code Hoist speeds including alternate speeds for both two-speed and inverter controls Availability of standard suspension types for each model Reeving Code Rope type code for each model Hoist duty rating 4.1 Height of Lift and Drum Code The height of lift along with the corresponding drum length code is listed for each basic model. In this table, height of lift is specified in meters. To convert meters to feet, multiply by 3.281. The drum code is included in the hoist model code. 4.2 Hoist Speeds The published hoist speeds are nominal. The actual hoist speed could vary ±15% when comparing hoists with the same nominal speed but with different reeving, different gearing and/or different motor type. Always use VFD hoisting controls when better speed accuracy is needed on hoists operating together. 4.3 Suspension Type Code Suspension types that are available for the hoist model are marked with a code. Special suspensions are not included here. Suspension Code in table Description J Special low headroom hoist L Low headroom hoist DH Double girder trolley high: Height above the rail is higher than the standard trolley - to get better headroom below the rail. D0 Double girder trolley standard DW Double girder trolley low: Height above the rail is lower than the standard trolley to get better overhead clearance but it increases headroom. N Normal headroom hoist F Foot mount 4.4 Reeving Code Reeving code Description Reeving code Description 021 2 part single 022 2 part double 041 4 part single 042 4 part double 061 6 part single 062 6 part double 081 8 part single 082 8 part double A2 2 part single Smaller rope diameter; reduced capacity; longer lift; SX4 low headroom hoists only A4 4 part single Smaller rope diameter; reduced capacity; longer lift; SX4 low headroom hoists only 4.5 Rope Type Code The rope type code is listed for each height of lift. The characteristics of the wire rope can be found in the Wire Rope section. The double-reeved hoists use two separate ropes a right-hand lay and a left-hand lay. See Wire Rope section for definition of Rope Type code. 4.6 Hoist Duty Rating ASME hoist duty ratings (H3, H4, etc.) apply to hoists marked with typical U.S. capacities (for example, 1 ton = 2000 lbs = 907 kg) and do not apply to hoists marked with typical metric capacities (for example, 1 metric ton = 1,000 kg = 2,200 lbs). FEM/ISO ratings apply to hoists with typical metric capacities. 9 RM-SX-TG-SPEC-2001-8-ENG.doc
4.7 Hoist Characteristics Table Load Contactor Inverter Suspension Drum Rope Duty Rating Control Control Ton Kg L D D D N F J HOL Gear Motor Speed Motor Speed ASME FEM/ISO Hoist Reeving H 0 W Code ft m Code Type Ratio code fpm m/min code fpm m/min 1 1000 SX1 021 J A 19'-8" 6 A E 133.8 PX 32/5.3 9.5/1.5 H4 2m/M5 B 39-4 12 2 2000 SX1 041 J B 19'-8" 6 A E 133.8 PX 16/2.6 4.8/0.7 H4 2m/M5 C 29-6 9 3/4 800 SX2 021 L H 0 N F A 39-4 12 A F 134.2 P1 40/6.6 12/2 T1 40 12 H4+ 3m/M6 C 62-4 19 1 1000 SX2 021 L H 0 N F A 39-4 12 A F 134.2 P1 40/6.6 12/2 T1 40 12 H4 2m/M5 C 62-4 19 1 ½ 1600 SX2 041 L H 0 N F A 19'-8" 6 A F 134.2 P1 20/3.1 6/1 T1 20 6 H4+ 3m/M6 C 31-2 9.5 2 2000 SX2 041 L H 0 N F A 19'-8" 6 A F 134.2 P1 20/3.1 6/1 T1 20 6 H4 2m/M5 C 31-2 9.5 1 1000 SX3 021 L H 0 N F A 39-4 12 A F 134.2 P2 40/6.6 12/2 T2 40 12 H4+ 3m/M6 C 62-4 19 G 106 P2 50/7.8 15/2.5 T2 50 15 H 87.7 P3 60/9.8 19/3.3 T3 60 19 1 ¼ 1250 SX3 021 L H 0 N F A 39-4 12 A F 134.2 P2 40/6.6 12/2 T2 40 12 H4+ 3m/M6 C 62-4 19 G 106 P2 50/7.8 15/2.5 T2 50 15 H 87.7 P3 60/9.8 19/3.3 T3 60 19 1 ½ 1600 SX3 021 L H 0 N F A 39-4 12 A F 134.2 P2 40/6.6 12/2 T2 40 12 H4 2m/M5 C 62-4 19 G 106 P2 50/7.8 15/2.5 T2 50 15 H 87.7 P3 60/9.8 19/3.3 T3 60 19 2 2000 SX3 041 L H 0 N F A 19'-8" 6 A F 134.2 P2 20/3.1 6/1 T2 20 6 H4+ 3m/M6 C 31-2 9.5 G 106 P2 25/3.9 7.5/1.3 T2 25 7.5 H 87.7 P3 30/4.9 9.5/1.6 T3 30 9.5 2 ½ 2500 SX3 041 L H 0 N F A 19'-8" 6 A F 134.2 P2 20/3.1 6/1 T2 20 6 H4+ 3m/M6 C 31-2 9.5 G 106 P2 25/3.9 7.5/1.3 T2 25 7.5 H 87.7 P3 30/4.9 9.5/1.6 T3 30 9.5 3 3200 SX3 041 L H 0 N F A 19'-8" 6 A F 134.2 P2 20/3.1 6/1 T2 20 6 H4 2m/M5 C 31-2 9.5 G 106 P2 25/3.9 7.5/1.3 T2 25 7.5 H 87.7 P3 30/4.9 9.5/1.6 T3 30 9.5 1 1000 SX4 A2 L C 73-9 22.5 B F 160.3 P2 40/6.6 12/2 T2 40 12 H4+ 3m/M6 D 98-5 30 H 104.7 P4 60/9.8 19/3.3 T4 60 19 1 ¼ 1250 SX4 A2 L C 73-9 22.5 B F 160.3 P2 40/6.6 12/2 T2 40 12 H4+ 3m/M6 D 98-5 30 H 104.7 P4 60/9.8 19/3.3 T4 60 19 1 ½ 1600 SX4 A2 L C 73-9 22.5 B F 160.3 P2 40/6.6 12/2 T2 40 12 H4 2m/M5 D 98-5 30 H 104.7 P4 60/9.8 19/3.3 T4 60 19 2 2000 SX4 A4 L C 36-1 11 A F 160.3 P2 20/3.1 6/1 T2 20 6 H4+ 3m/M6 D 49-2 15 H 104.7 P4 30/4.9 9.6/1.4 T4 30 9.6 2 ½ 2500 SX4 A4 L C 36-1 11 A F 160.3 P2 20/3.1 6/1 T2 20 6 H4+ 3m/M6 D 49-2 15 H 104.7 P4 30/4.9 9.6/1.4 T4 30 9.6 3 3200 SX4 A4 L C 36-1 11 A F 160.3 P2 20/3.1 6/1 T2 20 6 H4 2m/M5 D 49-2 15 H 104.7 P4 30/4.9 9.6/1.4 T4 30 9.6 10 RM-SX-TG-SPEC-2001-8-ENG.doc
Load Contactor Inverter Suspension Drum Rope Duty Rating Control Control Ton Kg L D D D N F J HOL Gear Motor Speed Motor Speed ASME FEM/ISO Hoist Reeving H 0 W Code ft m Code Type Ratio code fpm m/min code fpm m/min 1 ½ 1600 SX4 021 L H 0 N F B 39-4 12 D E 192.6 P3 30/4.9 9.5/1.6 T3 30 9.5 H4+ 3m/M6 C 59-0 18 F 160.3 P2 40/6.6 12/2 T2 40 12 H 0 N F E 98-5 30 D 78-9 24 F H 104.7 P4 60/9.8 19/3.2 T4 60 19 2 2000 SX4 021 L H 0 N F B 39-4 " 12 D E 192.6 P3 30/4.9 9.5/1.6 T3 30 9.5 H4+ 3m/M6 C 59-0 18 F 160.3 P3 40/6.6 12/2 T3 40 12 D 78-9 24 F H 104.7 P4 60/9.8 19/3.2 T4 60 19 H 0 N F E 98-5 30 2 1/2 2500 SX4 021 L H 0 N F B 39-4 " 12 D E 192.6 P3 30/4.9 9.5/1.6 T3 30 9.5 H4 2m/M5 C 59-0 18 F 160.3 P3 40/6.6 12/2 T3 40 12 H 0 N F E 98-5 30 D 78-90 24 F H 104.7 P4 60/9.8 19/3.2 T4 60 19 3 3200 SX4 041 L H 0 N F B 19-8 6 D E 192.6 P2 16/2.4 4.8/0.8 T2 16 4.8 H4+ 3m/M6 C 29-6 9 F 160.3 P2 20/3.1 6/1 T2 20 6 H 0 N F E 49-2 15 D 39-4 12 H 104.7 P4 30/4.9 9.5/1.6 T4 30 9.5 4 4000 SX4 041 L H 0 N F B 19-8 6 D E 192.6 P3 16/2.4 4.8/0.8 T3 16 4.8 H4+ 3m/M6 C 29-6 9 F 160.3 P3 20/3.1 6/1 T3 20 6 H 0 N F E 49-2 15 D 39-4 12 H 104.7 P4 30/4.9 9.5/1.6 T4 30 9.5 5 5000 SX4 041 L H 0 N F B 19-8 6 D E 192.6 P3 16/2.4 4.8/0.8 T3 16 4.8 H4 2m/M5 C 29-6 9 F 160.3 P3 20/3.1 6/1 T3 20 6 H 0 N F E 49-2 15 D 39-4 12 H 104.7 P4 30/4.9 9.5/1.6 T4 30 9.5 6 6000 SX4 061 H 0 N F C 19-8 6 E F 160.3 P3 13/2 4/0.6 T3 13 4 H4+ 3m/M6 D 26-3 8 H 104.7 P4 20/3.1 6/1 T4 20 6 E 32-9 10 7 ½ 7500 SX4 061 H 0 N F C 19-8 6 E F 160.3 P3 13/2 4/0.6 T3 13 4 H4 2m/M5 D 26-3 8 H 104.7 P4 20/3.1 6/1 T4 20 6 E 32-9 10 7 ½ 8000 SX4 081 H 0 N F C 14-9 4.5 E F 160.3 P3 10/1.5 3/0.5 T3 10 3 H4 2m/M5 D 19-8 6 H 104.7 P4 16/2.4 4.8/0.8 T4 16 4.8 E 24-7 7.5 10 10000 SX4 081 H 0 N F C 14-9 4.5 E F 160.3 P3 10/1.5 3/0.5 T3 10 3 H3 1Am/M4 D 19-8 6 H 104.7 P4 16/2.4 4.8/0.8 T4 16 4.8 E 24-7 7.5 11 RM-SX-TG-SPEC-2001-8-ENG.doc
Load Contactor Inverter Suspension Drum Rope Duty Rating Control Control Ton Kg L D D D N F J HOL Gear Motor Speed Motor Speed ASME FEM/ISO Hoist Reeving H 0 W Code ft m Code Type Ratio code fpm m/min code fpm m/min 4 4000 SX5 021 L H 0 W N F D 59-0 18 G E 223.8 P5 30/4.9 9.5/1.6 T5 30 9.5 H4+ 3m/M6 E 78-9 24 F 185.3 P5 40/6.6 12/2 T5 40 12 F 104-11 32 J H 113.8 P6 60/9.8 19/3.2 T6 60 19 H 0 W N F G 131-3 40 J 94.3 P7 80/13 24/4 T7 80 24 5 5000 SX5 021 L H 0 N F D 59-0 18 G E 223.8 P5 30/4.9 9.5/1.6 T5 30 9.5 H4 2m/M5 E 78-9 24 F 185.3 P5 40/6.6 12/2 T5 40 12 F 104-11 32 J H 113.8 P6 60/9.8 19/3.2 T6 60 19 H 0 W N F G 131-3 40 J 94.3 P7 80/13 24/4 T7 80 24 6 6300 SX5 041 L H 0 N F D 29'-6" 9 G E 223.8 P5 16/2.4 4.8/0.8 T5 16 4.8 H4+ 3m/M6 E 39-4 12 F 185.3 P5 20/3.1 6/1 T5 20 6 F 52-6 16 H 113.8 P6 30/4.9 9.5/1.6 T6 30 9.5 H 0 W N F G 65-7 20 J 94.3 P7 40/6.6 12/2 T7 40 12 7 ½ 8000 SX5 041 L H 0 N F D 29'-6" 9 G E 223.8 P5 16/2.4 4.8/0.8 T5 16 4.8 H4+ 3m/M6 E 39-4 12 F 185.3 P5 20/3.1 6/1 T5 20 6 F 52-6 16 H 113.8 P6 30/4.9 9.5/1.6 T6 30 9.5 H 0 W N F G 65-7 20 J 94.3 P7 40/6.6 12/2 T7 40 12 10 10000 SX5 041 L H 0 W N F D 29'-6" 9 G E 223.8 P5 16/2.4 4.8/0.8 T5 16 4.8 H4 2m/M5 E 39-4 12 F 185.3 P5 20/3.1 6/1 T5 20 6 F 52-6 16 H 113.8 P6 30/4.9 9.5/1.6 T6 30 9.5 H 0 W N F G 65-7 20 J 94.3 P7 40/6.6 12/2 T7 40 12 12 12000 SX5 061 H 0 W N F D 19-8 6 H F 185.3 P5 13/2 4/0.6 T5 13 4 H4 2m/M5 E 26-3 8 H 113.8 P6 20/3.1 6/1 T6 20 6 F 32-9 10 J 94.3 P7 25/3.9 7.5/1.3 T7 25 7.5 G 42-7 13 15 15000 SX5 061 H 0 W N F D 19-8 6 H F 185.3 P5 13/2 4/0.6 T5 13 4 H3 1Am/M4 E 26-3 8 H 113.8 P6 20/3.1 6/1 T6 20 6 F 32-9 10 J 94.3 P7 25/3.9 7.5/1.3 T7 25 7.5 G 42-7 13 15 16000 SX5 081 H 0 W N F D 14-9 4.5 H F 185.3 P5 10/1.5 3/0.5 T5 10 3 H4 2m/M5 E 19-8 6 H 113.8 P6 16/2.4 4.8/0.8 T6 16 4.8 F 26-3 8 J 94.3 P7 20/3.1 6/1 T7 20 6 G 32-9 10 20 20000 SX5 081 H 0 W N F D 14-9 4.5 H F 185.3 P5 10/1.5 3/0.5 T5 10 3 H3 1Am/M4 E 19-8 6 H 113.8 P6 16/2.4 4.8/0.8 T6 16 4.8 F 26-3 8 J 94.3 P7 20/3.1 6/1 T7 20 6 G 32-9 10 4 4000 SX5 022 H 0 W F D 27-10 8.5 D F 185.3 P5 40/6.6 12/2 T5 40 12 H4+ 3m/M6 E 42-7 13 + H 113.8 P6 60/9.8 19/3.2 T6 60 19 F 59-0 18 Dr J 94.3 P7 80/13 24/4 T7 80 24 G 82-0 25 H 109-11 33.5 J 150-11 46 5 5000 SX5 022 H 0 W F D 27-10 8.5 D F 185.3 P5 40/6.6 12/2 T5 40 12 H4 2m/M5 E 42-7 13 + H 113.8 P6 60/9.8 19/3.2 T6 60 19 F 59-0 18 Dr J 94.3 P7 80/13 24/4 T7 80 24 G 82-0 25 H 109-11 33.5 J 150-11 46 12 RM-SX-TG-SPEC-2001-8-ENG.doc
Load Contactor Inverter Suspension Drum Rope Duty Rating Control Control Ton Kg L D D D N F J HOL Gear Motor Speed Motor Speed ASME FEM/ISO Hoist Reeving H 0 W Code ft m Code Type Ratio code fpm m/min code fpm m/min 6 6300 SX5 042 H 0 W F D 13-1 4 D F 185.3 P5 20/3.1 6/1 T5 20 6 H4+ 3m/M6 E 21-3 6.5 + H 113.8 P6 30/4.9 9.5/1.6 T6 30 9.5 F 29-6 9 Dr J 94.3 P7 40/6.6 12/2 T7 40 12 G 41-0 12.5 H 54-1 16.5 J 75-5 23 7 ½ 8000 SX5 042 H 0 W F D 13-1 4 D F 185.3 P5 20/3.1 6/1 T5 20 6 H4+ 3m/M6 E 21-3 6.5 + H 113.8 P6 30/4.9 9.5/1.6 T6 30 9.5 F 29-6 9 Dr J 94.3 P7 40/6.6 12/2 T7 40 12 G 41-0 12.5 H 54-1 16.5 J 75-5 23 10 10000 SX5 042 H 0 W F D 13-1 4 D F 185.3 P5 20/3.1 6/1 T5 20 6 H4 2m/M5 E 21-3 6.5 + H 113.8 P6 30/4.9 9.5/1.6 T6 30 9.5 F 29-6 9 Dr J 94.3 P7 40/6.6 12/2 T7 40 12 G 41-0 12.5 H 54-1 16.5 J 75-5 23 12 12000 SX5 062 H 0 W F E 13-1 4 E F 185.3 P5 13/2 4/0.6 T5 13 4 H4+ 3m/M6 F 19-8 6 + H 113.8 P6 20/3.1 6/1 T6 20 6 G 26-2 8 Er J 94.3 P7 25/4.4 7.5/1.3 T7 25 7.5 H 36-1 11 J 49-2 15 15 15000 SX5 062 H 0 W F E 13-1 4 E F 185.3 P5 13/2 4/0.6 T5 13 4 H4 2m/M5 F 19-8 6 + H 113.8 P6 20/3.1 6/1 T6 20 6 G 26-2 8 Er J 94.3 P7 25/4.4 7.5/1.3 T7 25 7.5 H 36-1 11 J 49-2 15 15 16000 SX5 082 H 0 W F F 14-9 4.5 E F 185.3 P5 10/1.6 3/0.5 T5 10 3 H4 2m/M5 G 19-8 6 + H 113.8 P6 16/2.8 4.8/0.8 T6 16 4.8 H 26-2 8 Er J 94.3 P7 20/3.1 6/1 T7 20 6 J 37-8 11.5 20 20000 SX5 082 H 0 W F F 14-9 4.5 E F 185.3 P5 10/1.6 3/0.5 T5 10 3 H3 1Am/M4 G 19-8 6 + H 113.8 P6 16/2.8 4.8/0.8 T6 16 4.8 H 26-2 8 Er J 94.3 P7 20/3.1 6/1 T7 20 6 J 37-8 11.5 13 RM-SX-TG-SPEC-2001-8-ENG.doc
Load Contactor Inverter Suspension Drum Rope Duty Rating Control Control Ton Kg L D D D N F J HOL Gear Motor Speed Motor Speed ASME FEM/ISO Hoist Reeving H 0 W Code ft m Code Type Ratio code fpm m/min code fpm m/min 6 6300 SX6 021 0 N F C 50-10 15.5 K E 344.9 P6 30/4.9 9.5/1.6 T6 30 9.5 H4+ 3m/M6 D 68-10 21 F 269.1 P6 40/6.6 12/2 T6 40 12 E 91-10 28 M G 223.1 P7 50/7.8 15/2.5 T7 50 15 F 118-1 36 H 184.1 T8 60 19 G 154-2 47 J 143.6 T9 80 24 H 200-1 61 J 264-1 80.5 K 318-2 97 7 ½ 8000 SX6 021 0 N F C 50-10 15.5 K E 344.9 P6 30/4.9 9.5/1.6 T6 30 9.5 H4 2m/M5 D 68-10 21 F 269.1 P6 40/6.6 12/2 T6 40 12 E 91-10 28 M G 223.1 P7 50/7.8 15/2.5 T7 50 15 F 118-1 36 H 184.1 T8 60 19 G 154-2 47 J 143.6 T9 80 24 H 200-1 61 J 264-1 80.5 K 318-2 97 10 10000 SX6 021 0 N F C 50-10 15.5 K E 344.9 P6 30/4.9 9.5/1.6 T6 30 9.5 H3 1Am/M4 D 68-10 21 F 269.1 P7 40/6.6 12/2 T7 40 12 E 91-10 28 M G 223.1 P8 50/7.8 15/2.5 T8 50 15 F 118-1 36 H 184.1 T9 60 19 G 154-2 47 J 143.6 TA 80 24 H 200-1 61 J 264-1 80.5 K 318-2 97 12 ½ 12500 SX6 041 0 N F C 24'-6" 7.5 K E 344.9 P6 16/2.4 4.8/0.8 T6 16 4.8 H4+ 3m/M6 D 34-5 10.5 F 269.1 P6 20/3.1 6/1 T6 20 6 E 45-11 14 G 223.1 P7 25/3.9 7.5/1.3 T7 25 7.5 F 59-0 18 H 184.1 T8 30 9.5 G 77-1 23.5 J 143.6 T9 40 12 H 100-0 30.5 J 131-2 40 K 159-1 48.5 15 16000 SX6 041 0 N F C 24'-6" 7.5 K E 344.9 P6 16/2.4 4.8/0.8 T6 16 4.8 H4 2m/M5 D 34-5 10.5 F 269.1 P6 20/3.1 6/1 T6 20 6 E 45-11 14 G 223.1 P7 25/3.9 7.5/1.3 T7 25 7.5 F 59-0 18 H 184.1 T8 30 9.5 G 77-1 23.5 J 143.6 T9 40 12 H 100-0 30.5 J 131-2 40 K 159-1 48.5 20 20000 SX6 041 0 N F C 24'-6" 7.5 K E 344.9 P6 16/2.4 4.8/0.8 T6 16 4.8 H3 1Am/M4 D 34-5 10.5 F 269.1 P7 20/3.1 6/1 T7 20 6 E 45-11 14 G 223.1 P8 25/3.9 7.5/1.3 T8 25 7.5 F 59-0 18 H 184.1 T9 30 9.5 G 77-1 23.5 J 143.6 TA 40 12 H 100-0 30.5 J 131-2 40 K 159-1 48.5 14 RM-SX-TG-SPEC-2001-8-ENG.doc
Load Contactor Inverter Suspension Drum Rope Duty Rating Control Control Ton Kg L D D D N F J HOL Gear Motor Speed Motor Speed ASME FEM/ISO Hoist Reeving H 0 W Code ft m Code Type Ratio code fpm m/min code fpm m/min 20 20000 SX6 061 0 N F C 16-4 5 L E 344.9 P6 10/1.5 3/0.5 T6 10 3 H4+ 3m/M6 D 22-11 7 F 269.1 P6 13/2 4/0.6 T6 13 4 E 29-6 9 G 223.1 P7 16/2.4 4.8/0.8 T7 16 4.8 F 39-4 12 H 184.1 T8 20 6 G 50-10 15.5 J 143.6 T9 25 7.5 H 65-7 20 J 86-11 26.5 K 105-0 32 25 25000 SX6 061 0 N F C 16-4 5 L E 344.9 P6 10/1.5 3/0.5 T6 10 3 H4 2m/M5 D 22-11 7 F 269.1 P6 13/2 4/0.6 T6 13 4 E 29-6 9 G 223.1 P7 16/2.4 4.8/0.8 T7 16 4.8 F 39-4 12 H 184.1 T8 20 6 G 50-10 15.5 J 143.6 T9 25 7.5 H 65-7 20 J 86-11 26.5 K 105-0 32 30 30000 SX6 061 0 N F C 16-4 5 L E 344.9 P6 10/1.5 3/0.5 T6 10 3 H3 1Am/M4 D 22-11 7 F 269.1 P7 13/2 4/0.6 T7 13 4 E 29-6 9 G 223.1 P8 16/2.4 4.8/0.8 T8 16 4.8 F 39-4 12 H 184.1 T9 20 6 G 50-10 15.5 J 143.6 TA 25 7.5 H 65-7 20 J 86-11 26.5 K 105-0 32 30 32000 SX6 081 0 N F E 22-11 7 L E 344.9 P6 8/1.2 2.4/0.4 T6 8 2.4 H4 2m/M5 F 29-6 9 F 269.1 P7 10/1.5 3/0.5 T7 10 3 G 37-8 11.5 G 223.1 T8 13 4 H 49-2 15 H 184.1 T9 16 4.8 J 65-7 20 J 143.6 TA 20 6 K 78-8 24 40 40000 SX6 081 0 N F E 22-11 7 L E 344.9 P6 8/1.2 2.4/0.4 T6 8 2.4 H3 1Am/M4 F 29-6 9 F 269.1 P7 10/1.5 3/0.5 T7 10 3 G 37-8 11.5 G 223.1 P8 13/2 4/0.6 T8 13 4 H 49-2 15 H 184.1 T9 16 4.8 J 65-7 20 J 143.6 TA 20 6 K 78-8 24 6 6300 SX6 022 0 N F E 54-2 16.5 G E 344.9 P6 30/4.9 9.5/1.6 T6 30 9.5 H4+ 3m/M6 F 72-2 22 + F 269.1 P6 40/6.6 12/2 T6 40 12 G 96-9 29.5 Gr G 223.1 P7 50/7.8 15/2.5 T7 50 15 H 127-11 39 H 184.1 T8 60 19 J 170-7 52 J 143.6 T9 80 24 K 208-4 63.5 L 252-7 77 M 283-10 86.5 N 321-6 98 15 RM-SX-TG-SPEC-2001-8-ENG.doc
Load Contactor Inverter Suspension Drum Rope Duty Rating Control Control Ton Kg L D D D N F J HOL Gear Motor Speed Motor Speed ASME FEM/ISO Hoist Reeving H 0 W Code ft m Code Type Ratio code fpm m/min code fpm m/min 7 ½ 8000 SX6 022 0 N F E 54-2 16.5 G E 344.9 P6 30/4.9 9.5/1.6 T6 30 9.5 H4 2m/M5 F 72-2 22 + F 269.1 P6 40/6.6 12/2 T6 40 12 G 96-9 29.5 Gr G 223.1 P7 50/7.8 15/2.5 T7 50 15 H 127-11 39 H 184.1 T8 60 19 J 170-7 52 J 143.6 T9 80 24 K 208-4 63.5 L 252-7 77 M 283-10 86.5 N 321-6 98 10 10000 SX6 022 0 N F E 54-2 16.5 G E 344.9 P6 30/4.9 9.5/1.6 T6 30 9.5 H3 1Am/M4 F 72-2 22 + F 269.1 P7 40/6.6 12/2 T7 40 12 G 96-9 29.5 Gr G 223.1 P8 50/7.8 15/2.5 T8 50 15 H 127-11 39 H 184.1 T9 60 19 J 170-7 52 J 143.6 TA 80 24 K 208-4 63.5 L 252-7 77 M 283-10 86.5 N 321-6 98 12 ½ 12500 SX6 042 0 N F E 26'-3" 8 G E 344.9 P6 16/2.4 4.8/0.8 T6 16 4.8 H4+ 3m/M6 F 36-1 11 + F 269.1 P6 20/3.1 6/1 T6 20 6 G 47-7 14.5 Gr G 223.1 P7 25/3.9 7.5/1.3 T7 25 7.5 H 64-0 19.5 H 184.1 T8 30 9.5 J 85-4 26 J 143.6 T9 40 12 K 103-4 31.5 L 126-4 38.5 M 141-1 43 N 160-9 49 15 16000 SX6 042 0 N F E 26'-3" 8 G E 344.9 P6 16/2.4 4.8/0.8 T6 16 4.8 H4 2m/M5 F 36-1 11 + F 269.1 P6 20/3.1 6/1 T6 20 6 G 47-7 14.5 Gr G 223.1 P7 25/3.9 7.5/1.3 T7 25 7.5 H 64-0 19.5 H 184.1 T8 30 9.5 J 85-4 26 J 143.6 T9 40 12 K 103-4 31.5 L 126-4 38.5 M 141-1 43 N 160-9 49 20 20000 SX6 042 0 N F E 26'-3" 8 G E 344.9 P6 16/2.4 4.8/0.8 T6 16 4.8 H3 1Am/M4 F 36-1 11 + F 269.1 P7 20/3.1 6/1 T7 20 6 G 47-7 14.5 Gr G 223.1 P8 25/3.9 7.5/1.3 T8 25 7.5 H 64-0 19.5 H 184.1 T9 30 9.5 J 85-4 26 J 143.6 TA 40 12 K 103-4 31.5 L 126-4 38.5 M 141-1 43 N 160-9 49 16 RM-SX-TG-SPEC-2001-8-ENG.doc
Load Contactor Inverter Suspension Drum Rope Duty Rating Control Control Ton Kg L D D D N F J HOL Gear Motor Speed Motor Speed ASME FEM/ISO Hoist Reeving H 0 W Code ft m Code Type Ratio code fpm m/min code fpm m/min 20 20000 SX6 062 0 N F E 18'-1" 5.5 H E 344.9 P6 10/1.5 3/0.5 T6 10 3 H4+ 3m/M6 F 23-0 7 + F 269.1 P6 13/2 4/0.6 T6 13 4 G 31-2 9.5 Hr G 223.1 P7 16/2.4 4.8/0.8 T7 16 4.8 H 42-8 13 H 184.1 T8 20 6 J 55-9 17 J 143.6 T9 25 7.5 K 68-11 21 L 83-8 25.5 M 93-6 28.5 N 106-8 32.5 25 25000 SX6 062 0 N F E 18'-1" 5.5 H E 344.9 P6 10/1.5 3/0.5 T6 10 3 H4 2m/M5 F 23-0 7 + F 269.1 P6 13/2 4/0.6 T6 13 4 G 31-2 9.5 Hr G 223.1 P7 16/2.4 4.8/0.8 T7 16 4.8 H 42-8 13 H 184.1 T8 20 6 J 55-9 17 J 143.6 T9 25 7.5 K 68-11 21 L 83-8 25.5 M 93-6 28.5 N 106-8 32.5 30 30000 SX6 062 0 N F E 18'-1" 5.5 H E 344.9 P6 10/1.5 3/0.5 T6 10 3 H3 1Am/M4 F 23-0 7 + F 269.1 P7 13/2 4/0.6 T7 13 4 G 31-2 9.5 Hr G 223.1 P8 16/2.4 4.8/0.8 T8 16 4.8 H 42-8 13 H 184.1 T9 20 6 J 55-9 17 J 143.6 TA 25 7.5 K 68-11 21 L 83-8 25.5 M 93-6 28.5 N 106-8 32.5 30 32000 SX6 082 0 N F F 18'-1" 5.5 H E 344.9 P6 8/1.2 2.4/0.4 T6 8 2.4 H4 2m/M5 G 23-0 7 + F 269.1 P7 10/1.5 3/0.5 T7 10 3 H 31-2 9.5 Hr G 223.1 T8 13 4 J 42-8 13 H 184.1 T9 16 4.8 K 50-10 15.5 J 143.6 TA 20 6 L 62-4 19 M 70-6 21.5 N 80-5 24.5 40 40000 SX6 082 0 N F F 18'-1" 5.5 H E 344.9 P6 8/1.2 2.4/0.4 T6 8 2.4 H3 1Am/M4 G 23-0 7 + F 269.1 P7 10/1.5 3/0.5 T7 10 3 H 31-2 9.5 Hr G 223.1 P8 13/2 4/0.6 T8 13 4 J 42-8 13 H 184.1 T9 16 4.8 K 50-10 15.5 J 143.6 TA 20 6 L 62-4 19 M 70-6 21.5 N 80-5 24.5 17 RM-SX-TG-SPEC-2001-8-ENG.doc
Load Contactor Inverter Suspension Drum Rope Duty Rating Control Control Ton Kg L D D D N F J HOL Gear Motor Speed Motor Speed ASME FEM/ISO Hoist Reeving H 0 W Code ft m Code Type Ratio code fpm m/min code fpm m/min 12 ½ 12500 SX7 022 0 F F 50'-10" 15.5 K E 344.9 2 P6 32/4.6 9.6/1.4 2 T6 32 9.6 H4+ 3m/M6 G 67-3 20.5 + F 269.1 2 P6 39/6.2 12/2 2 T6 39 12 H 90-2 27.5 Kr G 223.1 2 P7 49/7.2 15/2.5 2 T7 49 15 J 123-0 37.5 H 184.1 2 T8 63 19 K 150-11 46 J 143.6 2 T9 78.7 24 L 182-5 55.6 M 205-0 62.5 N 232-11 71 15 16000 SX7 022 0 F F 50'-10" 15.5 K E 344.9 2 P6 32/4.6 9.6/1.4 2 T6 32 9.6 H4 2m/M5 G 67-3 20.5 + F 269.1 2 P6 39/6.2 12/2 2 T6 39 12 H 90-2 27.5 Kr G 223.1 2 P7 49/7.2 15/2.5 2 T7 49 15 J 123-0 37.5 H 184.1 2 T8 63 19 K 150-11 46 J 143.6 2 T9 78.7 24 L 182-5 55.6 M 205-0 62.5 N 232-11 71 20 20000 SX7 022 0 F F 50'-10" 15.5 K E 344.9 2 P6 32/4.6 9.6/1.4 2 T6 32 9.6 H3 1Am/M4 G 67-3 20.5 + F 269.1 2 P7 39/6.2 12/2 2 T7 39 12 H 90-2 27.5 Kr G 223.1 2 T8 49 15 J 123-0 37.5 H 184.1 2 T9 63 19 K 150-11 46 L 182-5 55.6 M 205-0 62.5 N 232-11 71 25 25000 SX7 042 0 F F 24-7 7.5 K E 344.9 2 P6 16/2.4 4.8/0.8 2 T6 16 4.8 H4+ 3m/M6 G 32-9 10 + F 269.1 2 P6 20/3.1 6/1 2 T6 20 6 H 44-3 13.5 Kr G 223.1 2 P7 25/4 7.5/1.3 2 T7 25 7.5 J 60-8 18.5 H 184.1 2 T8 32 9.8 K 75-5 23 J 143.6 2 T9 40 12 L 90-2 27.5 M 101-8 31 N 116-5 35.5 30 32000 SX7 042 0 F F 24-7 7.5 K E 344.9 2 P6 16/2.4 4.8/0.8 2 T6 16 4.8 H4 2m/M5 G 32-9 10 + F 269.1 2 P6 20/3.1 6/1 2 T6 20 6 H 44-3 13.5 Kr G 223.1 2 P7 25/4 7.5/1.3 2 T7 25 7.5 J 60-8 18.5 H 184.1 2 T8 32 9.8 K 75-5 23 J 143.6 2 T9 40 12 L 90-2 27.5 M 101-8 31 N 116-5 35.5 40 40000 SX7 042 0 F F 24-7 7.5 K E 344.9 2 P6 16/2.4 4.8/0.8 2 T6 16 4.8 H3 1Am/M4 G 32-9 10 + F 269.1 2 P7 20/3.1 6/1 2 T7 20 6 H 44-3 13.5 Kr G 223.1 2 T8 25 7.5 J 60-8 18.5 H 184.1 2 T9 32 9.8 K 75-5 23 L 90-2 27.5 M 101-8 31 N 116-5 35.5 18 RM-SX-TG-SPEC-2001-8-ENG.doc
Load Contactor Inverter Suspension Drum Rope Duty Rating Control Control Ton Kg L D D D N F J HOL Gear Motor Speed Motor Speed ASME FEM/ISO Hoist Reeving H 0 W Code ft m Code Type Ratio code fpm m/min code fpm m/min 40 40000 SX7 062 0 F F 16-4 5 L E 344.9 2 P6 10/1.6 3/0.5 2 T6 10 3 H4+ 3m/M6 G 21-3 6.5 + F 269.1 2 P6 13/2 4/0.6 2 T6 13 4 H 29-6 9 Lr G 223.1 2 P7 16/2.3 4.8/0.8 2 T7 16 4.8 J 41-0 12.5 H 184.1 2 T8 20 6 K 49-2 15 J 143.6 2 T9 25 7.5 L 60-8 18.5 M 67-3 20.5 N 77-1 23.5 50 50000 SX7 062 0 F F 16-4 5 L E 344.9 2 P6 10/1.6 3/0.5 2 T6 10 3 H4 2m/M5 G 21-3 6.5 + F 269.1 2 P6 13/2 4/0.6 2 T6 13 4 H 29-6 9 Lr G 223.1 2 P7 16/2.3 4.8/0.8 2 T7 16 4.8 J 41-0 12.5 H 184.1 2 T8 20 6 K 49-2 15 J 143.6 2 T9 25 7.5 L 60-8 18.5 M 67-3 20.5 N 77-1 23.5 60 60000 SX7 062 0 F F 16-4 5 L E 344.9 2 P6 10/1.6 3/0.5 2 T6 10 3 H3 1Am/M4 G 21-3 6.5 + F 269.1 2 P7 13/2 4/0.6 2 T7 13 4 H 29-6 9 Lr G 223.1 2 T8 16 4.8 J 41-0 12.5 H 184.1 2 T9 20 6 K 49-2 15 L 60-8 18.5 M 67-3 20.5 N 77-1 23.5 60 60000 SX7 082 0 F H 21-3 6.5 L E 344.9 2 P6 8/1.2 2.4/0.4 2 T6 8 2.4 H4 2m/M5 J 29-6 9 + F 269.1 2 P6 10/1.6 3/0.51 2 T6 10 3 K 36-1 11 Lr G 223.1 2 P7 13/2 4/0.6 2 T7 13 4 L 44-3 13.5 H 184.1 2 T8 16 4.8 M 50-10 15.5 J 143.6 2 T9 20 6 N 57-5 17.5 80 80000 SX7 082 0 F H 21-3 6.5 L E 344.9 2 P6 8/1.2 2.4/0.4 2 T6 8 2.4 H3 1Am/M4 J 29-6 9 + F 269.1 2 P7 10/1.6 3/0.51 2 T7 10 3 K 36-1 11 Lr G 223.1 2 T8 13 4 L 44-3 13.5 H 184.1 2 T9 16 4.8 M 50-10 15.5 N 57-5 17.5 19 RM-SX-TG-SPEC-2001-8-ENG.doc
5 Main Components - Hoist The hoist motor and gearbox, rope drum and the bottom block are the main hoist components. 1. Hoist motor 2. Hoist gearbox 3. Cover 4. Rotary limit switch 5. Gear guard 6. Drum gear 7. End plate A, B, C, D mounting bolts c_r1hm1a 6 Hoist Motor c_homo1a 1. Fan cover 2. Fan 3. Inspection port 4. Brake 5. Brake Disc 6. Mounting bolts 7. Friction plate 6.1 Hoist Motor Features Squirrel cage motor Double windings for two-speed motor, 6:1 speed ratio Synchronous speed See Motor Data IP55 protection Class F insulation Klixon type bimetal switch for thermal protection P1 P8 code designate standard two-speed hoist motors T1 TA code designate standard inverter hoist motors Power ratings See Motor Data 6.2 Optional Hoist Motor Features Standby heater (tropicalized protection is standard) IP66 protection Class H insulation 20 Bulletin: RM-SX-TG-SPEC-2001-8-ENG.doc
6.3 Ambient Conditions The standard motor is designed for operation at a minimum ambient temperature 10 C to a maximum ambient temperature 40 C and maximum altitude of 1000 meters (3280 feet). 6.4 P-Motors The alpha character P designates a standard two-speed hoist motor and the numeric character indicates power size. 6.5 T-Motors The alpha character T designates a standard inverter-duty hoist motor and the numeric character that follows indicates power size. The inverter-duty motors are specially designed for use with a variable frequency drive. 6.6 Motor Temperature Protection As standard, P or T type motor is equipped with normally closed, automatic reset thermal protector embedded in the stator winding(s). 6.7 Motor Cooling The hoist motors have ribbed outer frames to maximize convection cooling. The motors are normally equipped with an integral cooling fan that is driven directly by the motor shaft. The shaft driven fan is only effective when the motor is energized. In severe environmental conditions, such as high ambient temperature, a blower fan replaces the shaft driven fan to improve the cooling. 6.8 Hoist Motor Brake All hoist models are equipped with a disc brake to bring the load to a smooth and quick stop and to hold the load when the motor is not energized. The disc brake is integrated into the design of the motor and located between the motor end bell and the cooling fan. (On double reeved SX5 hoist models for drum lengths H and J, the disc brake is mounted to the gear case cover inline with the motor instead of mounted directly to the hoist motor.) A single disc with friction linings on both sides is used. The hub of the disc is engaged on the splined motor shaft. The disc can also move axially along the shaft to accommodate any friction lining wear. The brake is engaged by a number of springs that force a stationary pressure plate against the friction disc. An energized coil releases the brake. Since the brake is always engaged when the brake coil is not energized, the brake is a fail-safe system. 21 RM-SX-TG-SPEC-2001-8-ENG.doc
6.9 50 Hertz Hoist Motor Data Two-speed Duty Group Fem/ISO motor data PX P1 P2 P3 MF09ZA106 MF10M-106 MF10Z-106 MF10X-106 Synchronous speed RPM 3000 500 3000 500 3000 500 3000 500 Brake torque Nm 14 21 21 42 Max el. Brake torque Nm 32 63 77 El. Brake torque Nm 12.6 25 38 Power fact. Start 0.89 0.77 0.8 0.83 0.83 0.78 0.84 0.77 Starting torque Nm 11 12.4 10.7 25 22 34 28 Weight kg 21 22.6 30.6 35 Brake inertia kgm 2 0.00017 0.00017 0.00017 0.00045 Inertia w/o brake kgm 2 0.0039 0.0027 0.0049 0.0059 2m/M5 Load tm/min 8 10 20 25 240 300 Nominal power kw 1.5 0.25 1.8 0.25 3.6 0.5 4.5 0.7 Starts/h starts/h Nominal torque Nm 5.4 5.4 6.1 6.1 12.3 12.3 15.3 15.3 40 % ED 60 % ED Nominal speed RPM 2750 400 2780 420 2800 400 2750 415 30/3.5 min Short time duty min 30 15 60 15 60 15 30 15 Power factor 0.88 0.66 0.82 0.67 0.87 0.63 0.92 0.61 Efficiency 0.66 0.23 0.66 0.24 0.73 0.30 0.72 0.30 3m/M6 Load tm/min 8 16 20 300 300 Nominal power kw 1.5 0.2 2.9 0.4 3.6 0.5 Starts/h starts/h Nominal torque Nm 4.9 4.9 9.8 9.8 12.3 12.3 50 % ED 60 % ED Nominal speed RPM 2830 435 2850 420 2830 430 30/4 min Short time duty min Power factor 0.78 0.64 0.84 0.58 0.89 0.56 Efficiency 0.64 0.22 0.76 0.29 0.74 0.29 Duty Group Fem/ISO motor data P4 P5 P6 P7 MF11XA106 MF11X-106 MF13Z-106 MF13X-106 Synchronous speed RPM 3000 500 3000 500 3000 500 3000 500 Brake torque Nm 54 54 100 130 Max el. Br. Torque Nm 105 107 190 225 El. Br. Torque Nm 56 57 84 111 Power fact. Start 0.79 0.69 0.77 0.69 0.67 0.68 0.62 0.65 Starting torque Nm 57 48 67 56 107 84 120 111 Weight kg 51 59 86 99 Brake inertia kgm 2 0.0007 0.0007 0.0007 0.0017 Inertia w/o brake kgm 2 0.0101 0.0116 0.036 0.043 2m/M5 Load tm/min 40 50 80 100 240 300 Nominal power kw 7.5 1.2 9 1.4 15 2.5 18 3 starts/h starts/h Nominal torque Nm 24 24 30 30 48 48 62 62 40 % ED 60 % ED Nominal speed RPM 2650 355 2680 335 2740 420 2770 425 30/3.5 min Short time duty min 30 12 30 10 30 15 30 15 Power factor 0.90 0.56 0.90 0.61 0.87 0.59 0.91 0.56 Efficiency 0.73 0.28 0.72 0.28 0.78 0.45 0.80 0.47 3m/M6 Load tm/min 32 40 63 80 300 300 Nominal power kw 6 1 7.5 1.2 12 2 15 2.5 starts/h starts/h Nominal torque Nm 19.2 19.2 24 24 38 38 48 48 50 % ED 60 % ED Nominal speed RPM 2730 390 2760 370 2810 440 2820 440 30/4 min Short time duty min Power factor 0.87 0.52 0.87 0.56 0.82 0.52 0.89 0.47 Efficiency 0.74 0.27 0.79 0.28 0.80 0.43 0.82 0.43 22 RM-SX-TG-SPEC-2001-8-ENG.doc
Duty Group Fem/ISO motor data P8 * MF13XA106 Synchronous speed RPM 3000 500 Brake torque Nm 200 Max el. Br. Torque Nm 290 El. Br. Torque Nm 150 Power fact. Start 0.73 0.67 Starting torque Nm 165 140 Weight kg 99 Brake inertia kgm 2 0.0017 Inertia w/o brake kgm 2 0.043 2m/M5 Load tm/min 125 240 300 Nominal power kw 23 3.5 starts/h starts/h Nominal torque Nm 76 76 40 % ED 60 % ED Nominal speed RPM 2790 420 30/3.5 min Short time duty min 15 10 Power factor 0.84 0.57 Efficiency 0.83 0.44 3m/M6 Load tm/min 100 300 300 Nominal power kw 18 3 starts/h starts/h Nominal torque Nm 62 62 50 % ED 60 % ED Nominal speed RPM 2870 440 30/4 min Short time duty min Power factor 0.79 0.51 Efficiency 0.84 0.42 *The P8-motor can only be used on hoists with a FEM 1Am or ASME H3 duty rating. External fan on the P8 motor is standard. 23 RM-SX-TG-SPEC-2001-8-ENG.doc
6.10 50 Hertz Hoist Motor Currents Two-speed Currents Nominal voltage 230 V 400 V 500 V 660 V Used in voltage range 220 240 V 380 415 V 500 525 V 660 690 V ton m/min fast slow fast slow fast slow fast slow PX Starting current (A) MF09ZA106 Nominal current (A) 8 3.7 2.2 No-load current (A) 2.1 2.1 P1 Starting current (A) 35 6.1 20 3.6 16 2.9 12 2.2 MF10M-106 Nominal current (A) 10 8.5 4.9 4.9 2.8 3.9 2.2 3.0 1.7 8 7.5 4.3 4.3 2.5 3.4 2.0 2.6 1.5 6.3 7.0 4.3 4 2.5 3.2 2.0 2.4 1.5 5 6.6 4.3 3.8 2.5 3.0 2.0 2.3 1.5 No-load current (A) 6.3 4.9 3.6 2.8 2.9 2.2 2.2 1.7 P2 Starting current (A) 68 11.7 39 6.7 31 5.4 24 4.1 MF10Z-106 Nominal current (A) 20 14 7.1 8.2 4.1 6.6 3.3 5.0 2.5 16 12.2 6.6 7 3.8 5.6 3.0 4.2 2.3 12.5 10.4 6.4 6 3.7 4.8 3.0 3.6 2.2 10 9.2 6.6 5.3 3.8 4.2 3.0 3.2 2.3 No-load current (A) 7.8 7.5 4.5 4.3 3.6 3.4 2.7 2.6 P3 Starting current (A) 77 15 44 8.6 35 6.9 27 5.2 MF10X-106 Nominal current (A) 25 17 9.6 9.9 5.5 7.9 4.4 6.0 3.3 20 14.6 8.7 8.4 5 6.7 4.0 5.1 3.0 16 12.2 8.7 7 5 5.6 4.0 4.2 3.0 12.5 10.6 8.9 6.1 5.1 4.9 4.1 3.7 3.1 No-load current (A) 7.7 9.6 4.4 5.5 3.5 4.4 2.7 3.3 P4 Starting current (A) 118 22 68 12.7 54 10.2 41 7.7 MF11XA106 Nominal current (A) 40 30 17 17 9.5 14 7.6 10 5.8 32 24 15 13.7 8.6 11.0 6.9 8.3 5.2 25 19 15 11 8.6 8.8 6.9 6.7 5.2 20 17 15 10 8.6 8.0 6.9 6.1 5.2 No-load current (A) 12 16 7.0 9.2 5.6 7.4 4.2 5.6 P5 Starting current (A) 144 28 83 16 66 12.8 50 9.7 MF11X-106 Nominal current 50 33 19 19 11 15 8.8 12 6.7 40 28 16 16 9 13 7.2 9.9 5.5 32 23 15 13.5 8.9 10.8 7.1 8.2 5.4 25 19 15 11.1 8.9 8.9 7.1 6.7 5.4 No-load current (A) 14 17 7.8 10 6.2 8.0 4.7 6.1 P6 Starting current (A) 252 43 145 25 116 20 88 15 MF13Z-106 Nominal current (A) 80 56 24 32 14 26 11 19 8.5 63 43 21 25 12 20 9.6 15 7.3 50 38 21 22 12 18 9.6 13 7.3 40 35 21 20 12 16 9.6 12 7.3 No-load current (A) 28 23 16 13 13 10.4 9.7 7.9 P7 Starting current (A) 339 59 195 34 156 27.2 118 21 MF13X-106 Nominal current (A) 100 66 31 38 18 30 14 23 11 80 49 26 28 15 22 12.0 17 9.1 63 40 26 23 15 18 12.0 14 9.1 50 33 26 19 15 15 12.0 11.5 9.1 No-load current (A) 21 31 12 18 9.6 14.4 7.3 10.9 24 RM-SX-TG-SPEC-2001-8-ENG.doc
Currents Nominal voltage 230 V 400 V 500 V 660 V Used in voltage range 220 240 V 380 415 V 500 525 V 660 690 V ton m/min fast slow fast slow fast slow fast slow P8 Starting current (A) 389 68 212 39 170 31 128 24 MF13XA106 Nominal current (A) 125 85 40 49 23 39 18 30 14 No-load current (A) 43 38 25 22 20 18 15 13 25 RM-SX-TG-SPEC-2001-8-ENG.doc
6.11 60 Hertz Hoist Motor Data Two-speed Duty Group Fem/ISO motor data PX P1 P2 P3 MF09ZA106 MF10M-106 MF10Z-106 MF10X-106 Synchronous speed RPM 3600 600 3600 600 3600 600 3600 600 Brake torque Nm 14 21 21 42 Max el. Brake torque Nm 32 63 77 El. Brake torque Nm 12.6 25 38 Power fact. Start 0.87 0.73 0.76 0.81 0.77 0.73 0.78 0.74 Starting torque Nm 11 10 12.4 10.7 24.6 21.7 34 28 Weight kg 21 22.6 30.6 35 Brake inertia kgm 2 0.00012 0.00017 0.00017 0.00045 Inertia w/o brake kgm 2 0.0039 0.0027 0.0049 0.0059 2m/M5 Load tm/min 9.6 12 24 30 240 300 Nominal power kw 1.8 0.3 2.2 0.3 4.3 0.7 5.4 0.9 starts/h starts/h Nominal power hp 2.4 0.4 3 0.4 5.8 0.9 7.2 1.2 40 % ED 60 % ED Nominal torque Nm 5.4 5.4 6.1 6.1 12.3 12.3 15.3 15.3 30/3.5 min Nominal speed RPM 3350 500 3410 525 3400 500 3350 495 Short time duty min 30 15 60 15 60 15 30 15 Power factor 0.90 0.68 0.83 0.65 0.89 0.61 0.93 0.60 Efficiency 0.68 0.25 0.71 0.28 0.75 0.38 0.74 0.36 3m/M6 Load tm/min 9.6 19.2 24 300 300 Nominal power kw 1.8 0.25 3.5 0.5 4.3 0.7 starts/h starts/h Nominal power hp 2.4 0.33 4.7 0.7 5.8 0.9 50 % ED 60 % ED Nominal torque Nm 4.9 4.9 9.8 9.8 12.3 12.3 30/4 min Nominal speed RPM 3450 540 3450 520 3410 530 Short time duty min Power factor 0.80 0.58 0.87 0.54 0.91 0.53 Efficiency 0.71 0.25 0.75 0.36 0.75 0.34 Duty Group Fem/ISO motor data P4 P5 P6 P7 MF11XA106 MF11X-106 MF13Z-106 MF13X-106 Synchronous speed RPM 3600 600 3600 600 3600 600 3600 600 Brake torque Nm 54 54 100 130 Max el. Brake torque Nm 105 112 182 205 El. Brake torque Nm 56 64 82 101 Power fact. Start 0.73 0.67 0.75 0.68 0.60 0.64 0.55 0.59 Starting torque Nm 54 44 63 51 102 82 114 101 Weight kg 51 59 86 99 Brake inertia kgm2 0.0007 0.0007 0.0007 0.0017 Inertia w/o brake kgm2 0.0101 0.0116 0.036 0.043 2m/M5 Load tm/min 48 60 96 120 240 300 Nominal power kw [hp] 9 [12] 1.4 [1.9] 11 [14.8] 1.6 [2.1] 18 [24.1] 3 [4] 21[28.2] 3.5 [4.7] starts/h starts/h Nominal torque Nm 24 24 30 30 48 48 62 62 40 % ED 60 % ED Nominal speed RPM 3230 450 3250 440 3320 515 3360 520 30/3.5 min Short time duty min 30 12 30 10 30 15 30 15 Power factor 0.90 0.54 0.91 0.57 0.88 0.59 0.92 0.55 Efficiency 0.74 0.34 0.75 0.35 0.80 0.50 0.81 0.52 3m/M6 Load tm/min 38 48 76 96 300 300 Nominal power kw [hp] 7.2 [9.6] 1.2 [1.6] 9 [12] 1.4 [1.9] 14 [19] 2.3 [3] 18 [24.1] 3 [4] starts/h starts/h Nominal torque Nm 19.2 19.2 24 24 38 38 48 48 50 % ED 60 % ED Nominal speed RPM 3315 490 3320 470 3390 540 3410 540 30/4 min Short time duty min Power factor 0.88 0.49 0.90 0.53 0.85 0.52 0.90 0.47 Efficiency 0.76 0.33 0.77 0.35 0.82 0.48 0.83 0.49 26 RM-SX-TG-SPEC-2001-8-ENG.doc
Duty Group Fem/ISO motor data *P8 MF13XA106 Synchronous speed RPM 3600 600 Brake torque Nm 200 Max el. Brake torque Nm 290 El. Brake torque Nm 150 Power fact. Start 0.68 0.69 Starting torque Nm 160 140 Weight kg 99 Brake inertia kgm2 0.0017 Inertia w/o brake kgm2 0.043 2m/M5 Load tm/min 135 240 300 Nominal power kw 25 3.8 starts/h starts/h Nominal power hp 33.3 5.1 40 % ED 60 % ED Nominal torque Nm 69 69 30/3.5 min Nominal speed RPM 3430 530 Short time duty min 15 10 Power factor 0.87 0.54 Efficiency 0.86 0.49 3m/M6 Load tm/min 120 300 300 Nominal power kw 21 3.5 Nominal power hp 28 4.67 starts/h starts/h Nominal torque Nm 62 62 50 % ED 60 % ED Nominal speed RPM 3460 540 30/4 min Short time duty min Power factor 0.83 0.48 Efficiency 0.87 0.48 *The P8-motor can only be used on hoists with a FEM 1Am or ASME H3 duty rating. External fan on the P8 motor is standard. 27 RM-SX-TG-SPEC-2001-8-ENG.doc
6.12 60 Hertz Hoist Motor Currents Two-speed Currents Nominal voltage 220 V 380 V 460 V 575 V Used in voltage range 208 230 V 360 400 V 440 480 V 575 600 V ton m/min fast slow fast slow fast slow fast slow PX Starting current (A) 15 3.0 MF09ZA106 Nominal current (A) 9.6 3.7 2.2 No-load current (A) 2.1 2.1 P1 Starting current (A) 42 9 23 4.7 20 4.1 15 3.1 MF10M-106 Nominal current (A) 12 9.8 5.9 5.0 3.4 4.7 2.8 3.6 2.2 9.6 8.8 5.2 5.1 3.0 4.2 2.5 3.4 2.0 7.6 7.9 5.2 4.6 3.0 3.8 2.5 3.0 2.0 6 7.1 5.2 4.1 3.0 3.4 2.5 2.7 2.0 No-load current (A) 5.2 5.9 3 3.1 2.5 2.8 2 2.1 P2 Starting current (A) 90 15 52 8.8 43 7.3 34 5.8 MF10Z-106 Nominal current (A) 24 17 8.4 10 4.8 8.3 4.0 6.6 3.2 19.2 15.3 8.2 8.8 4.7 7.3 3.9 5.8 3.1 15 12.5 8.2 7.3 4.7 6 3.9 4.8 3.1 12 11.5 8.2 6.7 4.7 5.5 3.9 4.4 3.1 No-load current (A) 7.9 8.6 4.6 5.0 3.8 4.1 3.0 3.3 P3 Starting current (A) 102 18 59 10.2 49 8.4 39 6.7 MF10X-106 Nominal current (A) 30 22 11 13 6.5 10 5.4 8.2 4.3 24 18 10.2 10.3 5.9 8.5 4.9 6.8 3.9 19.2 15 10.2 8.7 5.9 7.2 4.9 5.8 3.9 15 13 10.2 7.3 5.9 6 4.9 4.8 3.9 No-load current (A) 8.4 11.3 4.8 6.5 4 5.4 3.2 4.3 P4 Starting current (A) 146 29 85 17 70.0 14.0 56 11.2 MF11XA106 Nominal current (A) 48 36 19 21 11 17 9.1 14 7.3 38 27 17 16 10.0 13 8.3 10.4 6.6 30 23 17 13 10.0 11 8.3 8.8 6.6 24 21 17 12 10.0 10 8.3 8.0 6.6 No-load current (A) 12.5 18 7.3 10.7 6.0 8.8 4.8 7.0 P5 Starting current (A) 167 31 97 18.2 80 15 64 12.0 MF11X-106 Nominal current (A) 60 42 21 24 12 20 10 16 8.0 48 33 18 19 10.5 16 8.7 12.8 7.0 38 28 18 16 10.3 13.5 8.5 10.8 6.8 30 23 18 13 10.3 11 8.5 8.8 6.8 No-load current (A) 14 20 8.1 11.5 6.7 9.5 5.4 7.6 P6 Starting current (A) 312 52 180 30 149 25 119 20 MF13Z-106 Nominal current (A) 96 67 27 39 16 32 13 26 10 76 54 27 31 15.7 26 13 21 10.4 60 46 25 27 14.5 22 12 18 9.6 48 36 25 21 14.5 17 12 13.6 9.6 No-load current (A) 27 25 16 14.5 13 12 10.4 9.6 P7 Starting current (A) 433 73 251 42 207 35 166 28 MF13X-106 Nominal current (A) 120 79 33 46 19 38 16 30 13 96 59 29 34 17 28 14 22 11.2 76 46 29 27 17 22 14 18 11.2 60 40 29 23 17 19 14 15 11.2 No-load current (A) 21 33 12 19 10 16 8.0 12.8 28 RM-SX-TG-SPEC-2001-8-ENG.doc
Currents Nominal voltage 220 V 380 V 460 V 575 V Used in voltage range 208 230 V 360 400 V 440 480 V 575 600 V ton m/min fast slow fast slow fast slow fast slow P8 Starting current (A) 460 121 266 70 220 35 176 28 MF13XA106 Nominal current (A) 135 98 47 57 27 47 22 38 18 No-load current (A) 40 41 23 24 19 20 15.2 16 29 RM-SX-TG-SPEC-2001-8-ENG.doc
6.13 100 Hertz Hoist Motor Data Inverter Motors Duty Group Fem/ISO motor data T1 T2 T3 T4 T5 T6 MF10MA200 MF10MB200 MF10MC200 MF11MA200 MF11MB200 MF13Z-200 Rated power kw 1.8 3.6 4.5 7.5 9 15 Synchronous speed RPM 3000 3000 3000 3000 3000 3000 Brake torque Nm 21 42 42 54 54 100 Pull-out torque Nm 16.6 32 40 80 80 165 Speed at 80% of rpm 2500 2500 2410 2500 2500 2700 pull-out torque Weight kg 23 23 23 37 37 59 Brake inertia kgm 2 0.00017 0.00017 0.00045 0.0007 0.0007 0.0007 Inertia w/o brake kgm 2 0.0027 0.0027 0.0027 0.0075 0.0075 0.024 2m/M5 Load tm/min 10 20 25 40 50 80 240 300 Nominal power kw 1.8 3.6 4.5 7.5 9 15 starts/h starts/h Nominal torque Nm 6.1 12.3 15.3 24 30 48 40 % ED 60 % ED Nominal speed RPM 2830 2790 2780 2860 2830 2910 30/3.5 min Short time duty min 60 60 60 30 30 30 Power factor 0.74 0.75 0.78 0.74 0.78 0.85 Efficiency 0.73 0.75 0.77 0.81 0.81 0.86 3m/M6 Load tm/min 8 16 20 32 40 63 300 300 Nominal power kw 1.5 2.9 3.6 6 7.5 12 starts/h starts/h Nominal torque Nm 4.9 9.8 12.3 19.2 24 38 50 % ED 60 % ED Nominal speed RPM 2860 2830 2830 2900 2860 2925 30/4 min Short time duty min Power factor 0.69 0.69 0.72 0.67 0.74 0.79 Efficiency 0.71 0.74 0.77 0.80 0.81 0.86 Duty Group Fem/ISO motor data T7 T8 T9 TA MF13ZA200 MF13ZB200 MF13ZC200 MF13X-200 Rated power kw 18 23 28 35 Synchronous speed RPM 3000 3000 3000 3000 Brake torque Nm 130 200 200 200 Pull-out torque Nm 165 200 275 350 Speed at 80% of pullout rpm 2700 2720 2710 2750 torque Weight kg 59 72 85 99 Brake inertia kgm 2 0.0017 0.0017 0.0017 0.0017 Inertia w/o brake kgm 2 0.024 0.030 0.036 0.043 2m/M5 Load tm/min 100 125 160 200 240 300 Nominal power kw 18 23 28 35 starts/h starts/h Nominal torque Nm 62 76 96 116 40 % ED 60 % ED Nominal speed RPM 2890 2880 2880 2880 30/3.5 min Short time duty min 30 30 30 30 Power factor 0.87 0.88 0.87 0.85 Efficiency 0.87 0.89 0.89 0.90 3m/M6 Load tm/min 80 100 125 160 300 300 Nominal power kw 15 18 23 28 starts/h starts/h Nominal torque Nm 48 62 76 96 50 % ED 60 % ED Nominal speed RPM 2910 2910 2920 2930 30/4 min Short time duty min Power factor 0.85 0.86 0.84 0.83 Efficiency 0.86 0.89 0.89 0.89 30 RM-SX-TG-SPEC-2001-8-ENG.doc