With the new LOGO! 8 you can monitor and control your application via PC, smartphone or tablet via the integrated web server with all conventional browsers via the integrated web server. Opening program and changing message text properties Note: In this example the Migration_of_older_programs_to_LOGO!_8.lsc program from the Migration of older programs to LOGO! 8 example is used which you can download in New examples for LOGO! 8 at the LOGO! homepage. Open your program. Page 1 of 18
Double click on the hardware type on the right, on the bottom of the diagram. Click the drop-down arrow and select 0BA8.Standard. Click OK to confirm the selection. Page 2 of 18
Double click the message text in order to open the block properties and make a tick under Message Destination for the web server and click OK. Repeat the process for each other message text that you want to display on the web server. Page 3 of 18
Downloading program in LOGO! 8 Now you can download your existing LOGO! program to LOGO! 8. Click the Download button or click Ctrl+D. Alternatively, you can also navigate in the menu to Tools > Transfer > PC -> LOGO!. Page 4 of 18
Select the interface for your connection to LOGO! and enter the IP address of your LOGO!. Click Test in order to check whether the connection is successful. If the connection is successful click OK in order to load the program into the device. Click Yes to set the LOGO! to STOP before the download. After the successful completion of the download, click Yes in order to set the LOGO! back to RUN. Page 5 of 18
Setting web server access Navigate to Tools > Transfer > PC -> Access control in the menu. Select the interface for your connection to LOGO! and enter the IP address of your LOGO!. Click Test in order to check whether the connection is successful. If the connection is successful click OK. Page 6 of 18
Click Yes to set the LOGO! to STOP. Navigate to the Web server access item and set the tick for Allow Web server access. Confirm the warning message that appears with Yes. Page 7 of 18
Tick Enable password protection for Web server access and enter a password. Page 8 of 18
Click Apply and then click Yes when the message appears in order to set the LOGO! back to RUN. Click OK to close the window. Open your Internet browser (PC, smartphone or tablet) and enter the IP address of the LOGO!, in this case: 192.168.0.10. Enter the password that you have specified in Tools > Transfer > Access control in LOGO!Soft Comfort V8, and click Log on. Page 9 of 18
The web server can called with the following devices and browsers: With all conventional PC Web browsers (Internet Explorer, Chrome, FireFox, ) With all smartphones (optimized resolution) (Android, ios, WindowsPhone, with the conventional Internet browser (Opera, Chrome,.)) With tablet PCs (optimized resolution) (Android, ios, Windows, with the conventional Internet browser) In the window that opens up, you will be shown all system information for your LOGO! basic module. Page 10 of 18
Operating web server and changing parameters Operating LOGO! Basic module Click LOGO! BM in order to open the virtual display of the LOGO! device. Click ESC, in order to enable the functions of the programmed cursor keys. Now you can operate the application with the cursor keys. Click the C1 cursor key. The Q1 output for the light is now set. By clicking the C1 cursor key again, the Q1 output is reset again. Note: In the example, in the message text, a bar chart each is used for displaying the lights which changes color together with the change of status. More information on how you can realize a display with change of colors with a bar chart can be found in the Migration of older programs to LOGO! 8 example in New examples for LOGO! 8 on the LOGO! homepage. Page 11 of 18
Now click ESC again, in order to disable the functions of the programmed cursor keys. The cursor keys C1 and C2 now serve for browsing between the different message texts. Click the C2 cursor key. The second message text is now displayed. Page 12 of 18
In order to get back to the previous message text, click the C1 cursor key. Changing parameters You can also change parameters via the virtual display of the LOGO! basic module or LOGO! TDE on the web server, provided no protection is enabled in the LOGO! program in the message text. Page 13 of 18
Click the parameter you would like to change. Parameters that cannot be changed are displayed in gray. Enter a new value for the parameter and click OK. In this example here, the parameter is a switch-off delay. The value is now changed to, for example, 07:00 seconds. Page 14 of 18
If the protection is enabled in the message text in the LOGO! program, the parameter cannot be changed and is displayed in gray. Page 15 of 18
Operating LOGO! TDE Click LOGO! TD in order to open the virtual display of LOGO! TDE. The functions of the programmed LOGO! TD function buttons are always enabled, unlike the virtual display of LOGO! BM (without clicking ESC). Click the F1 function key. The Q3 output for the light is now set. By clicking the F1 function key again, the Q3 output is reset again. Page 16 of 18
You can use the functions of the programmed cursor keys in the virtual display of LOGO! TDE just as for the virtual display of LOGO! BM. Click ESC and click the C1 cursor key. The Q1 output for the light is now set. By clicking the C1 cursor key again, the Q1 output is reset again. Now click ESC again, in order to disable the functions of the programmed cursor keys. The cursor keys C1 and C2 now serve for browsing between the different message texts just as for the virtual display of LOGO! BM. Click the C2 cursor key. The second message text is now displayed. Page 17 of 18
In order to get back to the previous message text, click the C1 cursor key. You can also change the parameters here, just as for the virtual display of LOGO! BM, the prerequisite is that no protection is enabled for the message text in the LOGO! program. Page 18 of 18