SIMPLE EXPERIMENT CONFIRMING THE NEGATIVE TEMPERATURE DEPENDENCE OF GRAVITY FORCE



Similar documents
TEMPERATURE DEPENDENCE OF GRAVITATIONAL FORCE: EXPERIMENTS, ASTROPHYSICS, PERSPECTIVES. A.L. Dmitriev

AS COMPETITION PAPER 2008

HIGH VOLTAGE ELECTROSTATIC PENDULUM

Theory of Heating by Induction

Prelab Exercises: Hooke's Law and the Behavior of Springs

CFD SIMULATION OF SDHW STORAGE TANK WITH AND WITHOUT HEATER

PS-6.2 Explain the factors that determine potential and kinetic energy and the transformation of one to the other.

AS COMPETITION PAPER 2007 SOLUTIONS

State Newton's second law of motion for a particle, defining carefully each term used.

E/M Experiment: Electrons in a Magnetic Field.

PHYS 101-4M, Fall 2005 Exam #3. MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question.

Practice final for Basic Physics spring 2005 answers on the last page Name: Date:

Calculating Heat Loss by Mark Crombie, Chromalox

Force on Moving Charges in a Magnetic Field

Lecture 24 - Surface tension, viscous flow, thermodynamics

Natural Convection. Buoyancy force

E. K. A. ADVANCED PHYSICS LABORATORY PHYSICS 3081, 4051 NUCLEAR MAGNETIC RESONANCE

Blackbody radiation derivation of Planck s radiation low

The Fundamentals of Thermoelectrics

Wednesday 16 January 2013 Afternoon

Energy and Energy Transformations Test Review

PHYSICAL QUANTITIES AND UNITS

APPLICATION NOTE AP050830

Free piston Stirling engine for rural development

Cambridge International Examinations Cambridge International General Certificate of Secondary Education

Lead & Magnet Wire Connection Methods Using the Tin Fusing Method Joyal A Division of AWE, Inc.

Physical Principle of Formation and Essence of Radio Waves

Rolling cylinder on a horizontal plane

State Newton's second law of motion for a particle, defining carefully each term used.

MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question.

Forms of Energy. Freshman Seminar

The Electrical Properties of Materials: Resistivity

NEW TECHNIQUE FOR RESIDUAL STRESS MEASUREMENT NDT

Determination of Thermal Conductivity of Coarse and Fine Sand Soils

1. The diagram below represents magnetic lines of force within a region of space.

Part I. Student Laboratory Manuals

Chapter 4: Transfer of Thermal Energy

Welding of Plastics. Amit Mukund Joshi. (B.E Mechanical, A.M.I.Prod.E)

MEASUREMENT OF VISCOSITY OF LIQUIDS BY THE STOKE S METHOD

Basic Equations, Boundary Conditions and Dimensionless Parameters

The Analytical Balance

Laminar and Turbulent flow. Flow Sensors. Reynolds Number. Thermal flow Sensor. Flow and Flow rate. R = Mass Flow controllers

Sample Questions for the AP Physics 1 Exam

Vibration measurements on future supports of mirrors M3 and M4 (ver. 1.0)

THERMAL STRATIFICATION IN A HOT WATER TANK ESTABLISHED BY HEAT LOSS FROM THE TANK

APPLICATION NOTE ULTRASONIC CERAMIC TRANSDUCERS

Chapter 3 Student Reading

User checks and maintenance of laboratory balances

Time allowed: 1 hour 45 minutes

INVESTIGATING THE EFFECT OF THE MAGNETIC FIELD FROM A WIRE ON A COMPASS

Physics 9e/Cutnell. correlated to the. College Board AP Physics 1 Course Objectives

Review Questions PHYS 2426 Exam 2

Fluid Mechanics: Static s Kinematics Dynamics Fluid

The Basic Principles of Sieve Analysis

Net thrust measurement of propellantless microwave thrusters* Yang Juan** Wang Yuquan Li Pengfei Wang Yang Wang Yunmin Ma Yanjie

Energy Transport. Focus on heat transfer. Heat Transfer Mechanisms: Conduction Radiation Convection (mass movement of fluids)

Lecture 30 - Chapter 6 Thermal & Energy Systems (Examples) 1

01 The Nature of Fluids

Physics Lab Report Guidelines

Mechanics. Determining the gravitational constant with the gravitation torsion balance after Cavendish. LD Physics Leaflets P

The content is based on the National Science Teachers Association (NSTA) standards and is aligned with state standards.

Spectra of pyroelectric X-ray generator

4 SENSORS. Example. A force of 1 N is exerted on a PZT5A disc of diameter 10 mm and thickness 1 mm. The resulting mechanical stress is:

Rock Bolt Condition Monitoring Using Ultrasonic Guided Waves

Conservation of Momentum and Energy

Solution Derivations for Capa #11

Calibration of Dallas sensors

Cambridge International Examinations Cambridge International General Certificate of Secondary Education

P O W E R C A P A C I T O R A S S E M B L I E S

Green Heating. Pupil Research Brief. Teachers Notes. Syllabus Coverage Subject Knowledge and Understanding. Route through the Brief UPIL ESEARCHER

ElectroMagnetic Induction. AP Physics B

UX-30 PERFORMANCE TESTING SUMMARY REPORT Revision 0

Journal of Engineering Science and Technology Review 2 (1) (2009) Lecture Note

DIRECT CURRENT GENERATORS

The University of the State of New York REGENTS HIGH SCHOOL EXAMINATION PHYSICAL SETTING PHYSICS. Friday, June 20, :15 to 4:15 p.m.

Cathode Ray Tube. Introduction. Functional principle

Physics 181- Summer Experiment #8 1 Experiment #8, Measurement of Density and Archimedes' Principle

American Society of Agricultural and Biological Engineers

Thermal Mass Availability for Cooling Data Centers during Power Shutdown

Thermodynamical aspects of the passage to hybrid nuclear power plants

PHYSICS 111 HOMEWORK SOLUTION #9. April 5, 2013

A LIGHTWEIGHT REAR BUMPER WITH CRASH WORTHY COMPARTMENT

The Three Heat Transfer Modes in Reflow Soldering

Millikan Oil Drop Experiment Matthew Norton, Jurasits Christopher, Heyduck William, Nick Chumbley. Norton 0

Objectives 200 CHAPTER 4 RESISTANCE

45. The peak value of an alternating current in a 1500-W device is 5.4 A. What is the rms voltage across?

Specific Heat Capacity and Latent Heat Questions A2 Physics

THE STRAIN GAGE PRESSURE TRANSDUCER

Candidate Number. General Certificate of Education Advanced Level Examination June 2012

Use the following image to answer the next question. 1. Which of the following rows identifies the electrical charge on A and B shown above?

The rate of change of velocity with respect to time. The average rate of change of distance/displacement with respect to time.

Rotational Motion: Moment of Inertia

Midterm Solutions. mvr = ω f (I wheel + I bullet ) = ω f 2 MR2 + mr 2 ) ω f = v R. 1 + M 2m

THE SECRET OF FREE ENERGY FROM THE PENDULUM

Mechanical Energy and Heat

36T Series Snap-Action Temperature Controls

Heat Pipe Selection Revision 12/04/2001

Vibrations of a Free-Free Beam

Current Staff Course Unit/ Length. Basic Outline/ Structure. Unit Objectives/ Big Ideas. Properties of Waves A simple wave has a PH: Sound and Light

Moving Coil or Moving Iron Controllable Actuators: How to make the good choice.

Transcription:

SIMPLE EXPERIMENT CONFIRMING THE NEGATIVE TEMPERATURE DEPENDENCE OF GRAVITY FORCE Alexander L. Dmitriev St-Petersburg National Research University of Information Technologies, Mechanics and Optics, 49 Kronverksky Prospect, St-Petersburg, 19711, Russia Results of weighing of the tight vessel containing a thermo-isolated copper sample heated by a tungstic spiral are submitted. The increase of temperature of a sample with masse of 8 g for about 1 С causes a reduction of its apparent weight for.7 mg. The basic sources of measurement errors are briefly considered, the expediency of researches of temperature dependence of gravity is recognized. Key words: gravity force, weight, temperature, gravity mass. PACS: 4.8-y. Introduction The question on influence of temperature of bodies on the force of their gravitational interaction was already raised from the times when the law of gravitation was formulated. The first exact experiments in this area were carried out at the end of XIXth - the beginning of XXth century with the purpose of checking the consequences of various electromagnetic theories of gravitation (Mi, Weber, Morozov) according to which the force of a gravitational attraction of bodies is increased with the growth of their absolute temperature [1-3]. That period of experimental researches was completed in 193 by the publication of Shaw and Davy s work who concluded that the temperature dependence of gravitation forces does not exceed relative value of 6 1 K and can be is equal to zero [4]. Actually, as shown in [5], those authors confidently registered the negative temperature dependence of gravitation force. Nevertheless, probably in the view of growth of popularity of the general theory of relativity (GR) by Einstein, Shaw and Davy have not dared to insist on their results. According to GR doctrines, the positive relative temperature dependence of gravitation force has the order of 1 it can not practically be observed [6]. 5 K which means that It is necessary to note that non-relativistic, including ether models of gravitation, as well as separate (sometimes exotic) hypotheses of the nature of gravitation, do not exclude rather "strong" temperature dependence of the force of gravitation [7,8]. Here it is pertinent to note the experiment by A.P. Shchegolev made in 1983 who, following the idea of the "thermodynamic" nature of gravitation, had observed the temperature reduction of weight of the massive steel sphere which was heated up with a beam of a powerful laser [9]; unfortunately, the accuracy of those experiments was rather insignificant. In the 9s, in the process of researches into the influence of the accelerated movement of a test body on the results of its exact weighing and on the basis of individual analogies of the

gravitational and electromagnetic phenomena, the author and his colleagues had executed measurements of apparent weights of samples of non-magnetic metal rods exited by ultrasound [1]. The longitudinal ultrasonic waves in rods, created by the piezoelectric converter, are accompanied by significant accelerations of the rod material microparticles which fact was used as a basis of measurements idea. During the experiments it was found that the results of measurements of rod weights were significantly influenced by the increase of their temperature, owing to both absorption of ultrasound and heat transfer from the piezo-converter. The frequency spectrum of temperature fluctuations of solid body particles lies in the field of hypersound frequencies and essentially exceeds the frequency of ultrasound, therefore such results are natural. The measurements of temperature dependence of weight (apparent mass) of metal samples executed by the specified technique had shown a rather strong negative temperature dependence of their weight with relative value γ in the range from 4.6 6 1 K for 6 a lead sample up to 11.6 1 K for duralumin one. The elementary phenomenological theory of temperature dependence of samples weight [1,11] had given a satisfactorily explanation of temperature dependence factor γ on density ρ and elastic properties (speed V of longitudinal ultrasonic waves) of material: V γ ; (1) ρ the same model allowed to prove the orientation dependence of weight of some crystals [1]. Though the results of measurements of negative temperature dependence of gravitation are in obvious disagreement with conclusions of GR, they do not contradict the earlier executed experiments or are challenged by anybody. On the contrary, in 1 the work of Chinese physicists (Liangzao Fan, Jinsong Feng, Wuquing Liu) investigating the temperature dependence of weight of metal samples (including samples from copper, gold and silver) was published in which the sign and value of temperature factor γ for a copper sample closely corresponded to our data [13]. Recently conducted measurements of temperature dependence of weight of the pile of piezoelectric converters excited on resonant frequency had also appreciably shown the reduction of piezo-ceramics weight with the growth of its temperature [14]. Experiment In the described experiment a tight vessel was weighed inside which there was a thermoisolated copper sample heated by a tungstic spiral through which the electric current was

passed. The design and appearance of the container are shown in Fig. 1 and Fig.. Diameter of the vessel is 63 mm, height - 87.5 mm, mass - 17.4 g. 3 Fig. 1. The design of the container. 1 - external, sealed tin vessel; - an envelope of the internal case (foil); 3 - copper cartridge wrapped up by mica and a tungstic spiral; 4 - a suspension bracket; 5 - «cold welding» (polymeric glue); 6 - copper conductors; 7 thermo-isolation envelopes (foam plastic). Fig.. Appearance of the container. Weighing was made by the elongation method (with readout of extreme angular positions of oscillating scales beam) on laboratory scales of ADL- model. Procedure of weighing consisted of three stages. At the first stage the container with a cold sample was weighed for 5-6 minutes. At the second stage of total duration equal to.5 minutes the electrodes of the container heater were connected for 35 seconds to a power supply source; the current in the heater circuit is.9a, resistance of the winding - 6.5 Ohm. At the third stage the continuous readout of current values of container weight was made for 8-9 minute. All mentioned manipulations were repeatedly and carefully fulfilled, the resulting error of measurement of weight of the container did not exceed 5 mcg. During measurements the temperature of walls and bottom of the container was equal to 4.9 ±.1 C. The temperature of the "hottest" central area of the container cover from the

moment of the heater switching ON has grown with speed of less than 4.1 / min ; so, in the first minutes after switching OFF of the heater power supply, the temperature of the container cover had increased by no more than.15 K. Under the specified conditions the influence of the air convection flows caused by difference of temperatures on the surface of the container and air in a closed box of scales was practically insignificant. Absence of a leak (hermetic sealing) in the container was controlled by usual methods. Typical time dependence of container apparent weight is shown in Fig. 3. 1 9 8 7 1 деление 1 мкг 6 5 4 3 1 1 3 4 5 6 7 8 9 1 11 1 13 14 15 16 17 18 19 1 3 4 5 6 7 8 9 3 31 3 33 34 35 36 37 38 39 4 41 4 43 44 45 46 47 48 49 5 51 5 53 54 55 56 57 58 59 6 61 6 63 Период отсчетов 18,3 с Fig. 3. Time dependence of changes of the container apparent weight. Shaped lines specify the moments of the beginning and the end of the second stage of weighing (the time scale of this stage is reduced). Vertical axis: 1 div 1 mcg; horizontal axis: period of sample 18.3 s. During the first -3 minutes after switching OFF of the heater the reduction of the container weight is maximal, reaching mcg, then during approximately 3 minutes a monotonous reduction of weight down to m 7mcg is observed. Discussion The calculated amount of heat supplied by the electric heater is approximately equal to 184 J. A part of this heat is dissipated in conductors and heat insulator, but significant, in amount of about 1J, part Q is transferred to copper sample 3 (Fig. 1) which has mass m 8g. The respective change T of average temperature of uniformly heated sample ( T = Q / mc, where c = 3.9 1 J / kg K is a specific thermal capacity of copper) T 9. The relative temperature change of sample weight, m γ =, () m T

6 is equal to γ =.8 1 K. This value differs by more than times from the result received in ultrasonic heating of a copper sample; nevertheless, the sign and the order of value γ correspond to the previous measurements [1-14]; comparing the specified results it is necessary to consider the difference of physical conditions of heating the sample by ultrasound and in the process of heat transfer. The general character of apparent weight reduction in Fig. 3 is explained by the process of distribution of heat in a copper sample of complex configuration (the heated part of the copper hollow cartridge makes approximately half of its length; the diameters of heated up and no-load parts of the cartridge differ) and, on the whole, correspond to similar dependence in measurements of weight of a brass core in Dewar s vessel [1]. In both cases the monotonous time dependence of the measured weights is explained by slow distribution of thermal wave in the samples being weighed. As shown by the special measurements, the temperature change of the top part of the 5 container during the experiment did not exceed.5, and the temperature of walls remained constant with accuracy of.1. Under these conditions, on the basis of Glaser s theory [15], the changes of apparent weight of the container, caused by air convection, and the change of buoyancy of the sample do not exceed temperatures of the cylinder surface of the area change m of apparent weight of a cylindrical sample is equal to 5 mcg. So, with a difference of air temperature t and A = 173cm and the diameter d = 6. 3cm, the m = 7 1/ 4 3 / 4 9. 1 Ad t. (3) With t =. from equation (3) which is obviously overestimated for conditions of the described experiment it follows that the total value of the observed weight change. m 75mcg which is approximately by an order less than It can be shown that the change of buoyancy caused by temperature change of the container volume owing to temperature change of the container case even by error of its apparent weight of less than 1 mcg. 1, causes a measurement On the whole, the results of the executed experiment will be coordinated with the dates [1-13] received earlier, confirming the fact of rather strong negative temperature dependence of force of the gravitation acting on the heated test body. *** As a note, we shall mark the following. If during the further experiments it will be shown that the specified temperature dependence has the universal character there probably will be necessary to update some conclusions of the well-known theories and models of gravitation.

6 In particular, the negative temperature dependence of gravitation force specifies that in the course of (astrophysical) gravitational collapse accompanying by an increase of temperature of collapse-mass, the realization of the so-called condition of "singular point" is impossible. Hence, the popular hypothesis of black holes can seem to be rather doubtful. Conclusions 1. An increase of temperature of thermo-isolated copper sample with mass of 8 g by value of about 1 С is accompanied by reduction of its apparent weight by more than.7 mg.. The observed, rather "strong" negative temperature dependence of body physical weight 6 with relative value by the order of 1 K does not contradict the known experiments on exact weighing the heated test body. 3. The experimental researches of temperature dependence of weight of bodies of the various structures, conducted in a wide range of temperatures, will promote the development of concepts of physics of gravitational interaction. References 1. Bogorodsky А. Vsemirnoe Tjagotenie, Кiev. «Naukova dumka», 1971.. Roseveare N. Mercury s Perihelion, Oxford, «Clarendon Press»,198. 3. Gillies G. Rep. Prog. Phys. (1997), Vol. 6, p. 151. 4. Shaw P. & Davy N. Phys. Rev. (193), Vol. 1, p. 68. 5. Dmitriev A. arxiv, physics/611173, Nov. 6. 6. Assis A. & Clemente R. Nuovo Cimento (1993), Vol. 18 B, 6, p. 713. 7. Sizov R. Magnetic Fundamental Particles in Physics of Magnetic and Electromagnetic Effects, Moscow, 7. 8. Bukhalov I. Inercia I gravitacia, Мoscow, «KomKniga», 7. 9. Shegolev A. Nugen grazer, SPb, «Anatolia», 9. 1. Dmitriev A., Nikushchenko E. & Snegov V. Measurement Techniques (3), Vol. 46, No., p. 115. 11. Dmitriev A. AIP Conf. Proc. 8, Vol. 969, p. 1163; 9, Vol. 113, p. 345. 1. Dmitriev A. & Chesnokov N. Measurement Techniques (4) Vol. 47, No. 9, p. 899. 13. Liangzao Fan, Jinsong Feng & Wuquing Liu Engineering Sciences, China (1), No.1(), p. 9. 14. Dmitriev A. & Nikushchenko E. arxiv:115.66v1 [physics. gen-ph], 16 May 11. 15. Glaser M. Metrologia (199), Vol. 7,, p. 95.