The only system with ISSF approval for all disciplines System overview and components SIUS AG Im Langhag CH-8307 Effretikon Switzerland Phone +4 52 354 60 60 Fax +4 52 354 60 66 www.sius.com admin@sius.com
B-KB--en 07/4 The approved system for shooting sport The system guarantees an unbeatable price/performance ratio and extreme reliability due to the integration of the most sophisticated electronic elements. All known ISSF-disciplines from 0-meter air rifle and pistol (including «running target») up to 300-meter big bore rifle are preprogrammed in the same control unit simply exchange the target for the different disciplines. Key points: The only system with ISSF authorization for all disciplines Applications for 0m, 25m, 50m, 300m Ideal for competitions and training Flexible use, handling barcode scanner, keyboard, remote controls or PC From a single stand-alone system to a large installation for a world cup, anything is possible LS0 HS0 HS25/50 S0 S30 RT0 «running target» 2
B-KB--en 07/4 basic installation Monitor, power supply and cables Firing line components The article group firing line includes all devices and parts required for the operation of individual lanes at the shooting range. A4 to the next lanes Article group cables and power supply A6 A5 A A3 A A2 Pos. Article no. Pcs. Description A Article group firing line A M94 Monitor TFT 0.4 (26cm) A2 CU94-CLUB Control unit, for clubs, schoools etc. (ISSF approval phase and 2) A2 CU94-ISSF Control unit, with software for ISSF competitions (ISSF approval phase, 2 and 3) A3 HST94V3 Monitor holder for CU94 A4 KL00-T T-Adapter fem/fem/male LTW IP67 A5 KL003-2.0 Cable LTW male RJ45 2.0m A6 KL00-2.0 Cable LTW male fem 2.0m Reference Country-specific power supply cable > page 3
B-KB--en 07/4 Control unit CU94 The control unit CU94 is the control device for the firing lane. Targets, programs and settings are selected here and, if required, shown on the display. The commands are entered either by means of the keyboard or of the remote control (PC or RC94). A A = LC display B = Keyboard C = Connection barcode scanner C B Connections for links to various devices and neighbouring lanes are located on the back of the control unit CU904. A B D E F G H I J C A = Service buttons = top: mode / bottom: LON service B = Monitor M94 C = Matrix printer D94 D = Graphic printer D2-N E = Shot indication / remote control / VGA monitor F = Interface RS232 G = Monitor, VGA b/w H = Power supply 24V DC I = RJ45 LonBus / power supply 24V J = Remote control / zoom Control unit CU94 CU94-CLUB Control unit, for clubs, schools etc. (ISSF approval phase and 2) Size (WxHxD): 90x77x295mm, weight:.05 kg (without optional accessory), Consumption: 3 W CU94-ISSF Control unit, with software for ISSF competitions (ISSF approval phase, 2 and 3) Size (BxHxT): 90x77x295mm, weight:.05 kg (without optional accessory), Consumption: 3 W Reference Country-specific power supply cable > page 4
B-KB--en 07/4 Monitor M94 The 0.4" TFT Monitor M94 is the viewing screen for the programs, system messages and results during shooting. The monitor is connected with the control unit CU94. The power supply unit is included in delivery. By default European 2-pin central plug. The power supply unit can be provided with an adapter and a country-specific power supply cable. 2 Monitor M94 M94 Monitor TFT 0.4 (26cm) Size (WxHxD): 265x275x25mm, weight:.7 kg Consumption: 24 W Optional accessory and spare parts 2 AS694 Adapter KlgerBu 2-pin C7fem C4male device 3pin With this adapter and the corresponding country-specific power supply cable, the power supply unit of the monitor M94 can be connected to every country-specific plug. Reference Country-specific power supply cable > page Monitor for spectators An additional VGA monitor can be connected to each firing line set to work in parallel with the shooting monitor. Depending on the model of the monitor, spectators can follow the competition shot by shot in graphic display. Monitor for spectators Monitor for spectators incl. corresponding connecting cables (on request) Reference Country-specific power supply cable > page 5
B-KB--en 07/4 Thermal printer D2-N The thermal printer D2-N is a graphic printer using thermopaper. The printer prints out the final results, the contents of the screen, and also the test results, if desired. It is directly connected to the control unit with the cable in Pos. 2. It is powered by a power supply device with a country-specific cable. The cable between the control unit and the printer must not be longer than 2m. 2 3 4 Thermal printer D2-N D2-N Thermal printer 0/220V for, including power supply Size (WxHxD): 50x65x30mm, weight: kg Consumption: 36 W Optional accessory and spare parts 2 CEBT93 Printer cable for thermal printer, parallel 3 AAG048 Thermal paper, 2mm wide 4 ME93D004 Mounting plate for printer D2-N on CU94 Reference Country-specific power supply cable > page 6
B-KB--en 07/4 Barcode scanner AAG33 The barcode scanner can be connected to the control unit CU94. This device enables operating the control unit the similar to the keyboard function. Furthermore, it is possible to scan in individual user programs created in the Barcode-Library. Barcode scanner AAG33 AAG33 Barcode scanner Size (WxHxD): 90x70x80mm, weight: 245 g Remote control RC94 The remote control (RC94) can be connected directly to the control unit CU94. It enables control of important functions directly from the shooter s position. ZOOM: Selects the next zoom level. MENU: Calls up the menu on the screen in which the following functions can be selected among others: «Delete screen» or «Print hard copy» MATCH: Switches from «Practice» to «Match» Remote control RC94 RC94 Remote control Size (BxHxT): 50x20x30mm, weight: 60 g Remote control RC-Zoom The remote control RC94 can be connected directly to the control unit CU94. By pushing the button, the preferred zoom level can be selected. Remote control RC-ZOOM RC-ZOOM Remote control for zoom Length: m 7
B-KB--en 07/4 Monitor holder HST94V3 for CU94 The monitor holder HST94V3 enables the connection of the monitor M94 with the control unit CU94 and the thermal printer D2-N. Monitor holder HST94 HST94V3 Monitor holder for CU94 8
B-KB--en 07/4 Shot sensor for big bore rifles The shot sensor differentiates the shots of one lane from shots of other lanes (cross shots, target errors). > see brochures of the corresponding targets S0 und S30 Crosstalk separators for the shot sensor We recommend the installation of crosstalk seperators between the individual lanes for firing lanes equipped with shot sensors. These prevent the acoustic and optical triggering of shots from neighbouring lanes. > see brochures of the corresponding targets S0 und S30 9
B-KB--en 07/4 0
B-KB--en 07/4 Country specific power supply cables The connection between device and socket is achieved with the use of country specific power supply cables. This is provided with the device coupling on one side and with a country specific plug on the other side. 2 3 4 5 Pos. Artikel-Nr. Bezeichnung AA0 Power supply cable 2m GB 2 AA02 Power supply cable 2m USA 3 AA09 Power supply cable 2m CH 4 AA0 Power supply cable 2m EU 5 AA26 Power supply cable 2m AUS
B-KB--en 07/4 SIUS worldwide There are SIUS representatives all around the globe. Find your local SIUS sales partner here: www.sius.com/en/representatives 2