8--99 8-/8 8-7/8 B 8-/4 A A Dim. A Leaf Width B ELEVATION F DESIGN Vertical edge seams mechanically interlocked Square hinge and lock edges 4-/ x.4 full mortise hinge prep Gov. 60/6 cyl lock prep...prefix VCR -/4 MATERIAL: Face sheets -- 0 gage, textured - galvanized steel. 6 gage steel flushmounted top and bottom channels. 7 gage steel hinge reinforcements. Core -- resin impregnated, sanded edge, kraft fiber honeycomb with a nominal one inch cell size. Core is laminated to top and bottom face sheets by means of moisture resistant, contact type adhesive. FINISH: BRONZE OR WHITE /8 Dim. A / / Core Top SECTION BB Top Honeycomb core Detail C 84 Door Opening Height Top Flush Laminated Detail C Welded /4 SECTION AA Lite Kits Narrow Lite 6-/8 x 6-/8 Half-Glass -/4 x 9-7/6 -/4 x 9-7/6 Full-Glass -/4 x 6-/ OMREV N/H Door for RF Frames Page.A
8--99 7-0 /8 8.88 4 HINGE SPACING 8 CYLINDRICAL LOCK 4.06 40.69 6 MORTISE LOCK NOMINAL DOOR OPENING HEIGHT ACTUAL LEAF HEIGHT 8. 9 Finished Floor DOOR ELEVATION ¾ VERTICAL SECTION SINGLE SWING DOUBLE SWING 7 / / NOMINAL DOOR OPENING WIDTH / NOMINAL DOOR OPENING WIDTH / HORIZONTAL SECTIONS (Conversion: =.4 mm, e.g., -/4 = 44.4 mm) OVERLAPPING ASTRAGAL 44 FOR -/4 THICK DOORS WITH OPTIONAL POLY-PILE INSERT 7 SPLIT ASTRAGAL 446 WITH WOOL-PILE INSERT 7 OVERLAPPING ASTRAGAL 7 446 FOR -/4 THICK DOORS IN IN SNAP-ON COVER LISTED Construction Features Page.B
8--99 6 GAGE END CHANNELS WELDED TO DOOR FLUSH TOP AND BOTTOM CHANNELS Inverted Channel (optional) VERTICAL EDGES MECHANICALLY INTERLOCKED HEMMED EDGES ALSO AVAILABLE SEAMLESS (WELDED OR BODY FILLER) Hairline Seam Epoxy Seal CLOSER REINFORCEMENT (OPTIONAL) LOCK PREPARATION GOV. 60/6 CYLINDRICAL TYPE 4 GAGE CHANNEL 6 LONG (C) (ANSI A.) -/4 BACKSET HINGE PREPARATION 4-/ X.4 HIGH, STANDARD OR HEAVY WT. FULL MORTISE HINGE PREPS ANSI A6.7 TEMPLATE NON-HANDED 7 GAGE REINFT. CLOSURE PLATES INCLUDED LOCK PREPARATION GOV. 86-4 MORTISE TYPE (M) (B) (P) (ANSI a.) -/4 BACKSET SIMILAR TO DETAIL LESS FACE CUTOUT SIMILAR TO DETAIL LESS ALL CUTOUT AND REINFORCEMENT 6 GLAZING TRIM 48 (APPLIED) FOR STANDARD FLUSH DOORS GLAZING TRIM 484 (APPLIED) FOR ALL FIRE DOORS PIERCED LOUVER 8 8 9 FOR HONEYCOMB CORE DOORS SNAP-IN BEAD /8 WIDE GLAZING POCKET /8 WIDE GLAZING POCKET LISTED L DESIGN Construction Features Page.C
8--99 STANDARD SIZES NOMINAL DOOR OPENING SINGLE WIDTH DOUBLE HEIGHT -0 4-0 -4 4-8 -6-0 6-8 -8-4 7-0 -0-8 7 - -0 6-0 7-0 -4 6-8 8-0 -6 7-0 9-0 -8 7-4 -0 7-8 4-0 8-0 FIRE DOORS LABELING AGENCIES: UNDERWRITERS LABOROTORY WARNOCK HERSEY FACTORY MUTUAL TEST: ASTM E-, UL0B, UBC 4- RATING: 0 MIN, ¾ HR, -/ HR, OR HR MAX. SIZE: 40 x 90 SINGLE 80 x 90 PAIR DESIGNS: F, G, N, & V Not all ratings are available in all sizes, designs and materials. MATERIAL PRODUCT SPECIFICATIONS: DOOR FACE SHEETS GRADE C.R. 0 Gage Textured Steel (4080 max.) -/4 thick steel doors shall be as manufactured by Ceco Door Products, Milan, TN USA. Doors shall conform to the Steel Door Institute guide specification ANSI/SDI 00-9; see chart below for performance classifications. OMEGA doors are made full-flush or (optional) seamless style. Faces sheets are commercial quality cold rolled steel conforming to ASTM A66 or A60 & A68...or (optional) hot-dipped galvanized steel (conforming to ASTM A6 or A64 & A) - see chart below. Omega full-flush doors have mechanically interlocked, hemmed, hairline seams on vertical edges and have no visible seams on faces. Doors specified seamless have no visible seams on faces or vertical edges. A one piece, chemically-treated, 99 lb., One inch cell, kraft-fibre honeycomb slab is securely bonded to both face sheets under pressure with contact adhesive. The top and bottom door edges are closed flush by 6 gage steel channels welded in place. The bottom edge channel can also be installed inverted (optional). Hardware Provisions: Hinge preparations are non-handed. Hinge edges are mortised for 4-/ standard and heavy weight hinges. 7 gage steel reinforcements are welded inside the door edge and are drilled and tapped for fasteners in accordance with ANSI A6.7. Hinge closing plates are included. The lock edge is square and is prepared for Gov. Series 86, or 60-6 locks in accordance with ANSI A (specify which). Optional closer reinforcement is a gage steel channel. Paint: -/4 steel doors shall be provided with one coat of oven-cured neutral color primer paint. Primer coat shall conform with ANSI A4.-990 with the thickness of primer coat not being less than 0.7 mils. The primer coat is a preparatory base for necessary finish painting. Colorstyle finish coat is also available from a selection of standard colors (optional). Colorstyle finish is electrostatically applied, oven-cured urethane enamel. For accurate color selectors ask for a Ceco Colorstyle chart. A60 GALV G90 RECOMMENDED DOOR FRAME MATERIAL Standard Duty STD OPT - 6 Gage Steel 0 Gage Steel (4080 max.) Standard Duty STD OPT - 6 Gage Steel 8 Gage Steel Heavy Duty STD OPT OPT 6 Gage Steel 6 Gage Steel Extra Heavy Duty STD OPT OPT 6 or 4 Gage Steel PERFORMANCE Core Thermal Characters: Sound Transmission Class: Physical Endurance Level: U Factor: 0.067 R Factor: 4.97 STC 6 (F Design, 8 Gage Face Sheets, ASTM E90-8 & E4-7 [Fully Operable]) Meets ANSI A. Performance Test, 0 GAGE: Level B (00,000 Cycles); 8 and 6: Level A (,000,000 Cycles) Product Specifications Page.D
8--99 WALK DOOR SYSTEM HONEYCOMB CORE PERFORMANCE TESTS Description Test Method Results. Slam Test ANSI A.-8,000,000 Cycles. Grade without failure. Twist or torque test ANSI A.-8 Max. defl. At 00# =.800 max. Permanent set =.09.. Acoustical properties ASTM E90-6T STC rating of. 4. Insulation properties ASTM C6 Mod. U factor = 0.04. R factor =.44.. Standard fire rating ASTM E Door is rated at -/ hours. * Must be installed in fire rated frame. (class B label) 6. Paint performance ASTM B7 00 hrs. salt spray. ASTM D47 00 hrs. humidity. Weatherometer 000 hrs. CONFORMANCE TO NATIONALLY ACCEPTED SPECIFICATIONS AND STANDARDS Requirements Complies. ANSI/SDI 00 YES. RR-D-7B YES. PBS 4-080 YES 4. CS 4-6 YES. CEGS-080 YES 6. NFGS-080 YES 7. H-08-, 080 YES 8. UL 0B/ANSI A. YES 9. ANSI A YES 0. ANSI A6.7 YES. NFPA 80 YES. ASHRAE 90 YES (if weatherstripped). ASTM D-47 00 hrs. 4. ASTM B-7 00 hrs.. ASTM A- A-60 Coating Designation 6. ASTM A-66 Uncoated 7. PS-4-66 YES 8. CS-9-6 YES 9. ANSI A4.-80 YES 0. ASTM C6 Mod. YES Performance and Conformance Data Page.4