2.02. Specifications. General. Products. Execution. Offset Pivots P-694 Top and Bottom Pivots

Transcription

1

2 2.02 Standard Specifications General Entrances Description Furnish all necessary materials, labor and equipment for the complete installation of aluminum entrance doors, door frames and hardware as shown on the drawings and specified herein. Doors and frames shall be as manufactured by Tubelite Inc., Reed City, Michigan. W,henever substitute products are to be considered, supporting technical literature, samples, drawings and performance data must be submitted ten (10) days prior to bid in order to make a valid comparison of the products involved. Test reports certified by an independent laboratory must be made available upon request. Products Materials Extrusions shall be of aluminum alloy 6063-T5 extruded within commercial tolerance and free from defects impairing strength and/or durability. Door stile and rail sections to be a minimum of,125 inch wall thinkness. Door frame sections to be of.080 inch minimum wall thickness, with glazing and door moldings a minimum of.050 inch. Steel tension rods of,375 inch diameter shall run the full width of the top and bottom rails and shall be fixed with steel plates and lock nuts. Door glazing shall be by means of an interior and exterior fixed gasket of high quality extruded elastomeric material. Door frame members shall have a continuous wool pile weatherstripping at the head and jamb members. Bottom rail weathersweep at threshold optional (architect specify). Door stops shall be of snap-in design on butt hinge and offset pivot applications, eliminating use of exposed screws. All door and frame members shall be accurate1 fitted to flush hairline joints, All H tack (Narrow Stile) Doors shall have an adjustable setting block in the top rail. Hardware Stock Entrance Doors and Frames shall have standard hardware as furnished by Tubelite, as follows: Butt Hinges P-092 Ball Bearing Butt Hinges P-1565 Push Bar P-1564 Pull Handle E % x 4 Threshold P-l 420 Deadbolt MS Lock P-1409 Lock Faceplate, or P-l 408 Lock Faceplate (Pairs of Doors) P-l 438 TubeliteiLCN Surface Mount Closer P-059 Flush Bolts (Pairs of Doors) Offset Pivots P-694 Top and Bottom Pivots P-1565 Push Bar P-1564 Pull Handle E-0019 % x 4 Threshold P-1420 Deadbolt MS Lock P-1409 Lock Faceplate, or P-1408 Lock Faceplate (Pairs of Doors) P-1438 Tubelite/LCN Surface Mount Closer P-059 Flush Bolts (Pairs of Doors) Center Pivots P-970 Concealed Overhead Closer with Bottom Pivot P-1565 Push Bars E % x 4 Threshold P-1420 Deadbolt MS Lock P-1409 Lock Faceplate, or P-1408 Lock Faceplate (Pairs of Doors) P-059 Flush Bolts (Pairs of Doors) Special hardware for custom doors and entrances shall be specified by the architect. Hardware furnished by others shall be sent to the door manufacturer for application. Finish All exposed framing surfaces shall be free of scratches and other serious blemishes. Finish to be: (architect select) Etched and clear anodized (AA-M12C22A31) - Clear (OA) Electrolytically deposited color (AA-M 12C22A44) - Champa ne (4K) Execution Light Am i3 er (2K) Amber (1 K) Statuary Bronze (3K) Black (OD) Fluoropolymer painted color Installation Shall be in accordance with the manufacturer s installation instructions and the approved shop drawings. Note: In keeping with Tubelite s policy of continuing product improvements, all specifications are subject to change without written notice by the manufacturer. TUBELITE SxxILm L ENIMKIS 1998

3 A 2 6 B Key Elevation & 1/4 Size Details a 3 KEY ELEVATIONS TRANSOM OPENING TRANSOM OPENING 7 1a 1 8 OPENING DIMENSION 1/ TRANSOM OPENING 4 5a 1/ 2a 4 1/2" 3a OPENING DIMENSION TRANSOM 1/ OPENING / 10" 3b 2

4 2.04 Standard Isometric Details Entrances P-679 TUBELITE srokmbmn(is 1998

5 E-4015 Standard 2.05 Entrances Isometric Details C, E-4531 E-4543 E-4545 C F;:973 E-4i20 E-4545 B E-0019 Right Hand NOTE: Double acting doors are not handed. TUBELITE 1998 ~~~..~R~NI~~LMI(I*I(I~

6 2.06 Jamb-Offset Pivot or Butt Hinge STANDARD SIZES 1 SINGLE DOORS 3'-0" X 7'-0" 3'-6" x 7'-0" DOUBLE DOORS 5'-0" X 7'-0" 6'-0" x 7'-0" ANCHORS N.B.T. P1713 (E4542) E4544 E DRJBH P1098 A E0437 BACKER ROD E4543 OPTIONAL 3/16" E0055 P1431 1/ GLASS SEALANT 1/ 9/16" Center of Pivot 3/ E0410 1/16" HINGESIDE 13/16" 2 1/8" 1/2"

7 2.07 Jamb-Offset Pivot or Butt Hinge STANDARD SIZES SINGLE DOORS 3'-0" X 7'-0" 3'-6" x 7'-0" DOUBLE DOORS 5'-0" X 7'-0" 6'-0" x 7'-0" 8 090DRJBL E4531 E4544 (E4542) P1713 ANCHORS N.B.T. E0437 P1098 A P1431 1/ GLASS E0055 3/16" E4543 OPTIONAL BACKER ROD E0410 1/8" LOCKSIDE SEALANT 2 1/8" 2"

8 2.08 Head-Offset Pivot or Butt Hinge 2 090DRTR BACKER ROD ANCHORS N.B.T. SEALANT 2" E45124 E4531 FRAME OPENING 1/8" 1/2" 2 1/8" E1375 P1098 A E0410 E0437 P1431

9 2.09 Bottom Rail-Offset Pivot or Butt Hinge 090DRBR 3 4 1/2" P1431 (EA. SIDE) E0410 1/ GLASS E0437 SETTING BLOCKS TIE ROD FRAME HEIGHT C L OF PIVOT E1376 3/ 3/16" 11/16" 1/2" FLOOR LINE E0019

10 BACKER ROD ANCHORS N.B.T Transom Bar and Head-Offset Pivot or Butt Hinge SEALANT 2" 160HEAD E E-4541 TRANSOM OPENING SEE GLAZING CHART (PG. 2.13) E4015 E4026 SEE BLOCK CHART 090TRAN 5 1/8" E /8" E1375 P1098A E4531 E0437 E0410 P1431

11 090STILE MEETING STILES 2.17 Door Stiles 7 PILE WEATHERING P013D E0056 E /8" STILE - E0056 STILE - E0087 5" STILE - E /8" STILE - E0057 STILE - E0088 5" STILE - E0418 PILE WEATHERING P013D E0057 E /8" STILE - E0057 STILE - E0088 5" STILE - E0418 HINGE OR LOCK STILE (CENTER HUNG) 2-1/8" STILE - E0055 STILE - E0086 5" STILE - E0416 HINGE OR LOCK STILE (BUTT HINGES OR OFFSET PIVOTS) HINGE OR LOCK STILE (BUTT HINGES OR OFFSET PIVOTS) MEETING STILES 2-1/8" 2-1/8" 5" HINGE OR LOCK STILE (CENTER HUNG) 5" 2-1/8" 5"

12 2.18 Top and Bottom Rails ALL RAILS CAN BE USED AS A TOP OR BOTTOM RAIL. E0148 3" TOP RAILS E /8" E /8" SCALE: FULL DETAIL SCALE:1/=1' E3021 MAY BE USED WITH ANY COMBINATION OF BOTTOM RAILS FOR DESIRED HEIGHT. 1/8" 1 9/16" HEIGHT OF RAIL,SHOWN IN EACH PART BOTTOM RAILS *TYPICAL POCKET DEPTH IS 1 9/16" EXCEPT THE FOLLOWING. E0148 = 1 1/2" E1375 = 1/ E1376 = 3/8" E0255 = 7/8" E " E /2" E /2" E3016 6" E0318 5" E /2" E0054 E

13 E Adjustable Astragal Option ADJASTR2 E1204 ADJASTR1 W/E1193 E2671 E1195 P938(2) 1/8" E /8" 2 1/8" E " E0056 5" 5" E0087 E-0417 E /8" E2671 E0417 E0056

14 2.25 Hardware Locations Notes: If panics are required in lieu of push bars, see Sec. 2 Pg. 24 for panic location. Vertical butt dimensions are for Tubelite standard 4-1/2" mortised butt. Dimensions from top (3-1/16") and bottom (3-11/16") remain the same if butt size and/or door opening changes. Pull Handle Push Bar Finish Floor Line with or without threshold dr.elev.cdr Note: On custom door opening heights, the bottom dimensions of 3-11/16" and top dimensions of 3-1/16" are constant. Intermediate dimensions of 68-1/ and 31-7/8" will vary accordingly. Dimensions of 39-1/2" and 36" are constant. STOREFRONT, CURTAINWALL & ENTRANCE SYSTEMS

15