Johnson Controls, Inc. now offers Mercury Security Corporation s high-quality access control hardware products, which can be integrated with the Johnson Controls P2000 Security Management System (SMS) Version 3.12 and later, providing added flexibility to help you meet the needs of your site s security requirements, using products from a well-known and time-tested security manufacturer. The following Mercury intelligent controllers are available separately or as part of a pre-configured security control panel assembly housed in a secure enclosure: CKM-EP2500 CKM-EP1501 CKM-EP1502 Wireless lock integration The integration to Mercury Controllers also enables P2000 integration with the Aperio line of wireless locks from ASSA ABLOY and the AD Series wired and wireless locks from Schlage. The Aperio wireless hub functions as a multi-lock (up to 8) reader module with all three of the Mercury intelligent network controllers. The Schlage PIM module functions as a reader module with the CKM-EP2500 and CKM-EP1501 intelligent network controllers. Access Platform CKM-EP2500 Controller The Access Platform CKM-EP2500 is an intelligent controller platform with native network support. This powerful and high-performance platform provides an Ethernet ready controller capable of efficiently managing a large network of Mercury access modules in multiple system designs. Based on the intelligent, next-generation Mercury Access Foundation, the CKM-EP2500 uses an Ethernet link to connect to the Microsoft Windows based P2000 host to provide access control, alarm management, and scheduled operations all in one package. The CKM-EP2500 is capable of elaborate processes and procedures without host intervention. Once configured, the CKM-EP2500 functions independently of the host, and is capable of controlling access, managing alarms, interfacing with an array of Mercury hardware devices, all while providing the decision-making oversight that each system configuration requires. CKM-EP2500 supports the range of reader technologies, including Wiegand, magnetic stripe, and biometric connectivity. As an intelligent system cornerstone, the CKM-EP2500 provides the greatest system capacity within Mercury s family of controller platforms. The Access Platform CKM-EP2500 is best deployed in systems where high-end capabilities and network-ready capacity are required. For high device counts, large numbers of readers, and a high volume of system activity, the CKM-EP2500 is the controller of choice. Network ready System intelligence decentralized Intelligent oversight and auxiliary monitoring to 64 doors Note: The CKM-EP2500 does not support shared mode and central mode communications with the P2000 host. Multi-card format support Multi-reader technology support Transport Layer Security (TLS) encryption support between P2000 server and controller Alarm keypad support for intrusion applications Code No. LIT-1900829 Issued February 26, 2016 CKM-EP2500 CKM-EP1501 CKM-EP1502 Optional Dual-LAN support for connection redundancy 1 CKM-EP2500 Controller s Primary Power Ethernet/Serial Ports CKM-EP2500 Feature 12-24 VDC +/- 10%, 300 ma maximum Primary 10/100 Ethernet Port 1: RS-232, 2-wire, dial-up, or secondary Ethernet Port 2: 2-wire Port 3: 2-wire, Two dedicated: tamper and power monitor 5.0 in. W x 6.0 in. L x 1.0 in. H (127 mm W x 152 mm L x 25 mm H) 10 to 93% Relative Non Condensing (RHNC) Connectivity Primary Port: 10/100 Ethernet, Dynamic Host Configuration Protocol (DHCP) Client, TLS, X.509 Access Control 500,000 cardholder capacity Card Formats 8 active card formats per CKM-EP2500 Entire card number reported on invalid read 18-digit (63-bit) UserId and 9-digit Personal Identification Numbers (PIN) maximum Personal Identify Verification (PIV) II, Common Access Card (CAC), and Transportation Worker Identification Credential (TWIC ) card compatible 32 access groups per cardholder 1. CKM-EP2500 must be installed in CKM enclosure to be UL Listed. 1 of 5
Access Platform CKM-EP1501 Controller Mercury s Access Platform CKM-EP1501 is an intelligent controller within the EP platform family and is built on the Mercury Access Foundation. The CKM-EP1501 provides a high-performance, Ethernet ready, cost-effective dual card reader panel capable of controlling a single opening. The CKM-EP1501 is expandable up to 8 downstream supervised input/output (SIO) controllers and up to 16 CKM-MR51E network ready door controllers for a total of 17 doors. Easy installation with Power Over Ethernet (PoE) makes this the top choice for a singledoor controller. Once configured, the CKM-EP1501 functions independently of the host and is capable of controlling access and managing elaborate processes such as relating selected system devices and their activity to other onboard devices, allowing actions and activities to transpire without host intervention. Offering powerful flexibility, the CKM-EP1501 is capable of interfacing with an array of reader technologies for a single opening. Reader ports support separate in/out readers and technologies that include Wiegand, clock and data,, magnetic stripe, keypads, LCD, and biometrics. The CKM-EP1501 seamlessly interfaces a single opening with a larger system for easy expansion. Providing all the intelligence and functionality of the Mercury family of controllers, the CKM-EP1501 is PoE capable and sets the standard for powerful, reliable performance, all at an economical price point. Decentralizes system intelligence Single-door interface Network ready to 17 doors Seamless P2000 software interface integration multiple card formats and card reader technologies PoE capable TLS encryption support between P2000 server and controller Triple gang footprint CKM-MR51E support (up to 16) SIO module interface capability (up to 8) CKM-EP1501 Controller s (Part 1 of 2) Power Input Power Output Reader Interface PoE Power Input 12.95 W, compliant to IEEE 802.3af or 12 VDC ± 10% 900 ma maximum power supply For UL installations, PoE powered devices shall not be used. Power for these devices must be provided by a UL 294 listed power limited source (12 VDC). 12 VDC at 650 ma, including reader and AUX output Reader Power: PoE: 12 VDC ± 10% or local power supply (12 VDC). (PTC limited 150 ma maximum) 2 general purpose programmable circuit type, and dedicated tamper CKM-EP1501 Controller s (Part 2 of 2) Outputs Reader Ports Keypad LED Buzzer 2 relays Form C, 2 A at 30 VDC CKM-EP1501 Feature Two Transistor Transistor Logic (TTL) reader ports or one 2-wire reader port capable of supporting two readers Multiplexed with card data Two-wire or one-wire bicolor support Only with one-wire LED Without Bracket: 5.5 in. W x 2.75 in. L x 0.96 in. H (140 mm W x 70 mm L x 24 mm H) With Bracket: 5.5 in. W x 3.63 in. L x 1.33 in. H (140 mm W x 92 mm L x 34 mm H) 10 to 93% RHNC Connectivity Door Control Primary Port: 10/100 Ethernet One physical barrier can be controlled using single or paired readers. Two reader ports: Mag, Wiegand, or ( on one reader port capable of supporting two readers) Two supervised inputs, two relays. Diagnostic LEDs. Dedicated tamper input. Access Control 240,000 cardholders 32 access groups per cardholder. 18-digit (63-bit) UserId and 9-digit PIN numbers maximum Card Formats 8 active card formats per CKM-EP1501 PIV-II, CAC, and TWIC card compatible Alarm Management Normally open/closed, unsupervised, supervised. Standard or custom end-of-line resistances 1. CKM-EP1501 must be installed in CKM enclosure to be UL Listed. 2 of 5
Access Platform CKM-EP1502 Controller Based on the intelligent Mercury Access Foundation, the Access Platform CKM-EP1502 platform uses an Ethernet link to connect to a Windows-based P2000 host to provide access control, alarm management, and scheduled operations, all in one package. With native connectivity, the CKM-EP1502 platform functions independently of the host, controlling access, managing alarms, and interfacing with an array of reader technologies through its Wiegand, magnetic stripe, and biometric connectivity. The result is the flexibility, versatility, and reliability you need for system success. Alarm Management capabilities include standard or customized end-of-line resistances; programmable sensitivity and hold time for line conditioning; entry delay latching and unlatching options; and entry-exit delays. The Access Platform CKM-EP1502 is the intelligent cornerstone of an access system, providing support for two readers and the capacity to expand to up to 64 doors. Reliably distributing intelligence, the CKM-EP1502 ensures that activities generated by select devices can be related to other devices for continued actions without host intervention. Decentralizes system intelligence Two-door interface with auxiliary I/O to 64 doors Multi-card format support Multi-reader technology support TLS encryption support between P2000 server and controller Alarm keypad support CKM-EP1502 Controller s Primary Power Ethernet/Serial Ports Outputs Reader Ports Power Keypad LED Buzzer 12-24 VDC +/- 10%, 500 ma maximum Primary 10/100 Ethernet Port 1: RS-232 Port 2:, 2-wire 8 general purpose: programmable circuit type; Two dedicated: tamper and power monitor 4 relays: Form C, 5 A at 30 VDC 2 reader ports Unregulated pass through (150 ma maximum); Signaling Card/Data, Wiegand, or Multiplexed with card data Two-wire or one-wire bicolor support Only with one-wire LED 6.0 in. W x 8.0 in. L x 1.0 in. H (152 mm W x 203 mm L x 25 mm H) 10 to 93% RHNC CKM-EP1502 Feature Connectivity Door Control Access Control Card Formats Primary Port: 10/100 Ethernet Port 1: RS-232, dial-up Port 2: 2-wire Two reader ports: Mag, Wiegand, or ; Eight supervised inputs, four relays. Diagnostic LEDs 250,000 cardholder capacity 32 access groups per cardholder 18-digit (63-bit) User ID and 9-digit PIN numbers maximum 8 active card formats per CKM-EP1502 PIV-II, CAC, and TWIC card compatible Alarm Management Normally open/closed, unsupervised, supervised. Standard or custom End-of-Line resistances. 1. CKM-EP1502 must be installed in CKM enclosure to be UL Listed. 3 of 5
CKM-EPxxxx Controller Comparison Matrix CKM-EPxxxx Controller Comparison Matrix /Feature 1 CKM-EP2500 CKM-EP1502 CKM-EP1501 Primary Power 12-24 VDC 12-24 VDC 12 VDC Power Over Ethernet No No Yes Dual LAN Option Yes No No Battery Coin cell, Field replaceable Coin cell, Field replaceable Rechargeable, Not field replaceable Onboard 2 dedicated (tamper and power monitor) 8 general purpose, 2 dedicated (tamper/power monitor) 2 general purpose, Dedicated tamper Onboard Outputs 0 4 relays 2 relays Onboard Readers 0 2 reader ports 2 reader ports (first reader port could be used instead for downstream communications) Reader Port Voltage N/A 12-24 V or 12 V 12 V Downstream Ports 2 1 1 (replaces first reader port) Card DB Memory 15 MB 6 MB 6 MB Real Time Clock Yes Yes No ASSA ABLOY Aperio Hub Yes Yes Yes (Up to 8) Support Schlage PIM400-485 Support Yes No Yes Maximum Number of Readers 64 64 17 Maximum Number of Supervised 512 512 128 /Outputs (SIOs) without reader modules Maximum Number of CKM-MR51E 32 32 16 modules Anti-Passback Support Yes Yes Yes Snow-Emergency Support Yes Yes Yes 1. Some features were not evaluated by Underwriters Laboratories. Ordering Information Part Number CKM-EP1501 CKM-EP1501 Mercury network controller CKM-EP1502 CKM-EP1502 Mercury network controller CKM-EP2500 CKM-EP2500 Mercury network controller CKM-DLAN CKM-EP2500 Dual LAN Module Related Documentation Document Title CKM-EP2500 Mercury Controller Hardware CKM-EP1501 Mercury Controller Hardware CKM-EP1502 Mercury Controller Hardware Document Number Part No. 24-10707-23 Part No. 24-10707-7 Part No. 24-10707-15 4 of 5
P2000 and Mercury Controllers Integration P2000 Server P2000 Workstation CKM-MR51E IP Network Wide Area Network CKM-EP2500 CKM-EP1502 CKM-EP1501 Door 2 2 2 2 16 General Purpose 16 General Purpose 16 General Purpose to 64 to 64 to 17 P2000 and Mercury Controllers Integration 5 of 5