MOBILE PAINT MANUFACTURING CO., INC. PAINTING SYSTEMS GUIDE

Welcome to the MOBILE PAINT MANUFACTURING CO., INC. PAINTING SYSTEMS GUIDE PLEASE NOTE This document may take several minutes to load depending on the speed of your connection. Do not try to navigate through the document until the status bar at the bottom of your screen indicates "Done". Best viewed with Acrobat Reader version 5.0 available free from Adobe. Go to Painting Systems Guide Go to Painting Systems Guide Introduction Go to Painting Systems Guide Index

MOBILE PAINT MANUFACTURING CO., INC. PAINTING SYSTEMS GUIDE Go to Painting Systems Guide Introduction Go to Painting Systems Guide Index

INDEX TO PAINTING SYSTEMS GUIDE INTRODUCTION Introduction to Mobile Paints and the Painting Systems Guide GUIDE TO GOVERNMENT SPECIFICATIONS A cross reference of Federal / Military Paint Specifications and our equivalent commercial products SSPC SPECIFICATIONS FOR SURFACE PREPARATION A summary of surface preparation specifications by the Society for Protective Coatings (SSPC) FERROUS METALS Coating systems for steel surfaces for non-immersion service at ambient temperatures FERROUS METAL PRIMER GUIDE Overview of Anticorrosive Metal Primers GALVANIZED METALS & ALUMINUM Coating systems for galvanized metal and aluminum for non-immersion service at ambient temperatures HIGH TEMPERATURE SURFACES Coating systems for steel surfaces in service at temperatures up to 1,000 O F EXTERIOR MASONRY Coating systems for masonry, including cement block, concrete, brick, plaster, stucco, and gypsum board INTERIOR MASONRY Coating systems for interior cement block, plaster, concrete, and gypsum board surfaces WOOD FINISHES Interior and exterior finishes for wood FLOOR FINISHES Interior and exterior finishes for wood and concrete floors and decks WATER STORAGE TANKS Interior and exterior painting systems for water storage tanks - Potable water, fire protection water, plant process water, and de-mineralized water. WASTE WATER TREATMENT PLANTS Painting systems for industrial waste water treatment plants and sewage treatment plants. MARINE FINISHES Marine painting systems for commercial, military and recreational vessels INDEX OF PRODUCT DATA SHEETS

MOBILE PAINT MANUFACTURING CO., INC. Introduction to Painting Systems Guide Mobile Paints, founded in 1921, has over 80 years experience in formulating top-quality architectural, industrial and marine coatings for tropical and subtropical climates. We were pioneers in developing effective and environmentally safe mildew inhibitors as well as lead-free paints for residential and industrial service. Basically conservative, we put quality first and are proud of our logo: This guide is a series of paint systems specifications for industrial, institutional, commercial and residential applications, covering both specific materials, such as ferrous metals, and specific services, such as floors. Product data sheets are available online at our Web Site (www.blpmobilepaint.com) and an index can be found in this publication. Material Safety Data Sheets are also available on request. Individual sections of this guide cover Water Storage Tanks and Waste Water Treatment Plants. Alternate systems are offered wherever practical in order to give additional flexibility in matching finish and service required. Maintenance upgrade systems are included where applicable. Systems include surface preparation and application details. The scope has been expanded to include maintenance painting for upgrading deteriorated systems to high performance coatings. Except as noted, all products listed are lead-free, chromate-free, mercury-free, and compliant with current VOC regulations. As regulations may change, consult your Mobile Paint representative for products meeting specific requirements in your area. Mobile Paints offers a complete line of marine finishes for commercial, military and recreational vessels. Marine systems are also covered in this guide. We invite your inquiry and will be happy to work with you on your specific requirements. It is impossible to cover each specific situation in a guide such as this. For particular situations, consult your BLP Mobile Paint representative for recommendations. We appreciate your confidence in our products and look forward to being of service. Go to Painting Systems Guide Index

GUIDE TO GOVERNMENT SPECIFICATION COATINGS This guide contains information concerning products manufactured by Mobile Paint Mfg. Co., Inc. and those products application as performance equivalents to certain Federal and Military Specification coatings. These BLP Mobile Paint products are manufactured from quality raw materials to rigid quality standards and are recommended as performance equivalents to the listed government specifications under their intended conditions of use. Under some conditions of use, government specification coatings, while giving satisfactory performance, may not be the coating or coating system most ideally suited to the job. Technical assistance is available through the Mobile Paint Laboratory in developing a coating system which is ideally suited to your requirements. Unless so designated, the BLP Mobile Paint products cannot be certified as specification material. These products are offered as substitutes only and should not be represented otherwise. If you have special requirements or if the specification in question is not contained in the list, contact our Customer Service Department for assistance. This information is offered in good faith and believed to be accurate at the time of publication. This information is subject to change without prior notice PLEASE NOTE: (*) to note the following: Government Specification Numbers in the following list are annotated with one or two asterisks * Denotes that a Special Order Product is available which meets the specification requirements ** Denotes that the Mobile Paint Product listed meets the specification requirements FED / MIL SPEC BLP MOBILE PAINT NUMBER DESCRIPTION ALTERNATE PRODUCT SS-W-110 ** Water Repellent, Colorless Silicone Base Dub-L-Tite Silicone Exterior Waterproofing, Clear 74-12 TT-C-535 Coating, Epoxy, Two Component, for Interior MoPoxY TM HS Epoxy on Metal, Wood, Concrete and Masonry Coating 613-series TT-C-542 Coating, Polyurethane, Oil Free, Mothane TM MC-63 63-AF-1 Moisture Curing (Type II Class A) TT-C-550 Coating System, Glaze, Interior, MoPoxY TM HS Epoxy for Masonry Surfaces Coating 613-series TT-C-555 ** Masonry Coating System, Textured WEATHER-TITE TM ELASTOMERIC Wall Coating 43-20 1

FED / MIL SPEC BLP MOBILE PAINT NUMBER DESCRIPTION ALTERNATE PRODUCT TT-E-485 * Enamel, Semigloss, Rust Inhibiting Special RUS-KIL Semi-gloss 52-Series (Special Order Only) or RUS-KIL Hi-Hide 655 series TT-E-487 Enamel, Floor & Deck SpeeDeck Polyurethane Floor & Deck Enamel 50-series TT-E-489G * Gloss Synthetic Enamel Class A - NAM-A-LAC Alkyd All Purpose Air Drying Enamel 30-series TT-E-489H * Enamel, Alkyd, Gloss, Low VOC Special order only TT-E-490 * Enamel, Silicone Semi-gloss Exterior Silicone Alkyd Enamel 13-Series & 432-series (High gloss only) TT-E-491 Gloss Synthetic Enamel Class A - NAM-A-LAC Alkyd All Purpose Air Drying Enamel 30-series TT-E-505 Enamel, Odorless Alkyd, Interior High Gloss, NAM-A-LAC Alkyd All Purpose White & Light Tints Enamel 30-series TT-E-506 Enamel, White, Gloss, Interior NAM-A-LAC Alkyd All Purpose Enamel 30-series TT-E-508 * Interior Semi-gloss Enamel (Alkyd) COVENTRY Lustarite Alkyd Tints & White Satin Enamel 135-series TT-E-509 Enamel, Odorless, Alkyd Interior, COVENTRY Lustarite Alkyd Semi-gloss, Whites & Tints Satin Enamel 135-series TT-E-529 Semi-gloss Synthetic Enamel Type I - Air Dry Special Order Only TT-E-543 * Interior Enamel Undercoat (Alkyd) COVENTRY Wood Sealer 19-8 Tints & White TT-E-545 Enamel, Odorless, Alkyd Interior, COVENTRY Wood Sealer 19-8 Undercoat, Flat Tints & White TT-E-1593 Enamel, Silicone Alkyd, Gloss Jack Tar Silicone Yacht Finish 432-series 2

FED / MIL SPEC BLP MOBILE PAINT NUMBER DESCRIPTION ALTERNATE PRODUCT TT-E-1793 Enamel, Semi-gloss, Metal & Wood COVENTRY Lustarite Alkyd Satin Class A - Air Dry Enamel 135-series TT-F-1098 Filler, Block, Solvent Thinned for Bloc-Fil TM 60-7 (Water Thinned) Porous Surfaces (NOTE: Substitute Product) TT-P-19 Exterior Acrylic Emulsion WEATHER-TITE TM MOPACOTE 100% Acrylic Latex Flat House Paint 40-series TT-P-25 * Primer, Paint, Exterior Ready-Mixed WEATHER-TITE TM Southern White for Wood Primer with Busan 5-6 TT-P-28 * Paint, Aluminum Heat Resistant (1200 F) BLP Silicone Heat Resistant Aluminum 11-61 TT-P-29 * Paint, Latex Base, Interior Flat, White & Tints COVENTRY Latex Flat Wall Paint 35-series TT-P-31 Red & Brown Iron Oxide Paint (Roof SPEED PRIME TM Red Oxide 9-78 & Barn Paint) TT-P-32 Blackboard Coating, Type I - Black, Chalkboard Slating, Black 17-11 Type II - Green & Green 17-44 TT-P-37 Paint, Oil (Alkyd), Exterior Trim WEATHER-TITE TM Permanent Trim & Accent 25-series TT-P-52 Paint, Oil (Alkyd) Wood Shakes and Rough Weather Protector Exterior Wood Siding Stain & Preservative 1411-40 TT-P-55 Paint, Polyvinyl Acetate Emulsion (Exterior) Smooth-Cote Exterior Vinyl Acrylic House Paint Flat 291-series TT-P-59 Paint, Ready-Mixed, International Orange Jack Tar Yacht Deck Enamel Safety Orange - 450-61 TT-P-61 Ready-Mixed Black Paint RUS-KIL Rust Inhibiting Enamel Black 10-11 3

FED / MIL SPEC BLP MOBILE PAINT NUMBER DESCRIPTION ALTERNATE PRODUCT TT-P-71 Exterior Ready-Mixed Green Paint RUS-KIL Rust Inhibiting Enamel 10-series TT-P-81 Paint, Ready-Mixed, Exterior Medium Shades WEATHER-TITE TM 5-series SOUTHERNIZED Mildew Resistant House Paint TT-P-85 Paint, Traffic and Airfield Marking, BLP Street Marking Oil Base Paint Solvent Based 58-16 White, 58-51 Yellow TT-P-96 * Paint, Latex Base, for Exterior Wood WEATHER-TITE TM 40-series and Metal Surfaces. White & Tints 100% Acrylic Flat House Paint TT-P-102 * Paint, Oil Alkyd (Modified) Exterior, Chalk and WEATHER-TITE TM 5-series Fume Resist., Lead-Free, Ready-Mixed, White SOUTHERNIZED Oil House Paint TT-P-115 Exterior Traffic Paint White & Yellow Type I BLP Street Marking Oil Base Paint 58-series TT-P-620 Exterior Masonry Conditioner Chalk-Koter, White 29-16 TT-P-636 * Primer Coating, Alkyd, Wood and RUS-KIL Rust Inhibiting Primer, Ferrous Metal Red 10-10 TT-P-641 Primer Coating, Zinc Dust-Zinc Oxide Special Order Only (For Galvanized Surfaces) TT-P-645A * Primer, Paint, Zinc Chromate Prymall 35 Yellow Zinc Chromate Primer 9-55 TT-P-645B * Primer, Paint, Zinc Molybdate Zinc Moly Primer Yellow 80242 (May be stocked in some locations) TT-P-650 Interior White Primer, Latex, Type I, COVENTRY Prymall 2 Acrylic Ready-Mixed Primer and Sealer 19-7 TT-P-664C * Primer Coating, Rust Inhibiting, Lacquer Mo-Bar TM Universal Primer Resisting Red 28-DR-105 4

FED / MIL SPEC BLP MOBILE PAINT NUMBER DESCRIPTION ALTERNATE PRODUCT TT-P-664D * Primer Coating, Rust Inhibiting, Lacquer Mo-Bar TM PM III Universal Primer Resisting Red 28-DR-160 TT-P-1510 Paint, Latex, Exterior for Wood Surfaces WEATHER-TITE TM 40-series 100% Acrylic Latex Flat House Paint TT-P-1511 * Paint, Latex Base, Type I Semi-gloss COVENTRY Latex Semi-gloss Enamel 1335-series TT-P-1728 Paint, Latex, Interior COVENTRY Latex Flat Wall Paint 35-series TT-P-1975 Primer Coating, Latex Base, Exterior ACR-A-LAC TM Acrylic Latex (For Metal) Primer Red 330-7 or H 2 0 RUS-KIL Primer 310-9 TT-P-1984 Primer Coating, Latex Base, Exterior WEATHER-TITE TM 100% Acrylic (Undercoat for Wood) Latex Universal Primer 6-6 TT-R-248 Remover-Solvent Type, Water Rinsable Super XL Water Wash Paint Remover 74-24 TT-S-176 Sealer, Surface, Varnish Type, Floor, NUWOOD Poly-Var Floor Wood or Cork Varnish, Gloss 70-12 TT-S-1992 Stain, Latex, Exterior for Wood Surfaces Weather Protector Int./Ext. Acrylic Latex Stain 44-series TT-T-266 Thinner, Dope and Lacquer Lacquer Thinner #15 75-21, Lacquer Thinner #60 75-22, Lacquer Thinner #1000 75-23 TT-T-291 * Thinner, Paint, Mineral Spirits, MoPaxOl Low Odor Paint & Type I Regular Varnish Thinner 75-1 TT-T-306 Thinner, Synthetic Resin Enamel TEC Thinner 75-11 TT-V-51 * Varnish, Asphalt Asphaltum #1 61-11 5

FED / MIL SPEC BLP MOBILE PAINT NUMBER DESCRIPTION ALTERNATE PRODUCT TT-V-71 Interior Varnish NUWOOD Special Floor & Trim Varnish 70-13 TT-V-81 * Varnish, Mixing for Aluminum Special Order Only Type I and Type II TT-V-85 Varnish, Oil, Low sheen, Brush or Spray NUWOOD MoPaCo-Var TM Flat Water White Varnish 70-21 TT-V-109 Varnish, Spar, Alkyd-Resin NUWOOD MoPaCo-Var TM Gloss Water White Varnish 70-23 TT-V-119 Varnish, Spar, Phenolic Resin Jack Tar 100% Phenolic Marine Spar Varnish 470-31 TT-V-121 Water Resisting Spar Varnish Jack Tar 100% Phenolic Marine Spar Varnish 470-31 DOD-E-698 * Enamel, Alkyd, Deck, Black SpeeDeck Polyurethane Floor & Deck Enamel 50-series (Not Semi-gloss) DOD-E-699 * Enamel, Deck Gray SpeeDeck Polyurethane Floor & Deck Enamel 50-series (Not Semi-gloss) DOD-E-700 * Enamel, Deck, Interior, Gray SpeeDeck Polyurethane Floor & Deck Enamel 50-series (Not Semi-gloss) DOD-E-1115 * Enamel, Interior and Exterior, Special Order Only White (Formula 30) DOD-E-1265 Enamel, Ship, Exterior, Ocean Gray NAM-A-LAC Alkyd All Purpose Enamel 30-series MIL-C-4556d * Steel Tank Coating System MoPoxY TM HB Primer 40-DR-5 & MoPoxY TM HB White 40-AW-13 6

FED / MIL SPEC BLP MOBILE PAINT NUMBER DESCRIPTION ALTERNATE PRODUCT MIL-E-15090 * Enamel, Equipment, Light Gray Special Order Only (Formula 111) Type I & Type III DOD-P-15146 * Exterior Enamel, Dull Black Formula 104 RUS-KIL Rust Inhibiting Enamel Flat Black 10-12 DOD-P-15328 ** Primer (Wash) Pretreatment Vinyl Wash Primer 9-42 MIL-P-15931 ** Paint, Anti-fouling, Vinyl Formula 121 Jack Tar Vinyl Anti-fouling Red 473-73 MIL-P-19451 ** Paint, Antifouling, Cold Plastic, Formula 105 Jack Tar VIP Cold Plastic Anti-fouling Red 473-71 DOD-P-21035 ** Paint, High Zinc Dust Galv. Repair Coating Gray 80166 (May be stocked in some locations) MIL-C-22750 Coating, Epoxy/Polyamide MoPoxY TM HS Epoxy Coating 613-series DOD-P-23236A Paint Coating Systems, Steel Ship Tank, Class 1-40-AW-13 Fuel and Salt Water Ballast, Type I Class 2-40-AX-7 Class 3-28-DH-50 Class 4 - Not Available MIL-P-23377 ** Primer Coating, Epoxy-Polyamide MoPoxY TM Catalyzed Epoxy Primer 40-DN-4 MIL-P-24441 * Paint, Epoxy-Polyamide Special Order Only Type I, Type III or Type IV (May be stocked in some locations) DOD-P-24596 * Coating Compounds, Non-Flaming, Special Order Only Fire Protective DOD-P-24607 * Enamel, Interior, Non-Flaming (Dry), Special Order Only Chlorinated Alkyd Resin, Semigloss DOD-E-24635 * Enamel, Silicone Alkyd Copolymer Special Order Only (May be stocked in some locations) 7

FED / MIL SPEC BLP MOBILE PAINT NUMBER DESCRIPTION ALTERNATE PRODUCT MIL-P-28577 Primer, Water Reducible WEATHER-TITE TM 100% Acrylic Latex Universal Primer 6-6 MIL-P-28578 Paint, Water Reducible, Semi-Gloss WEATHER-TITE TM 100% Acrylic Latex Gloss House Paint 140-series MIL-P-28582 Primer Coating, Exterior WEATHER-TITE TM Southern White Primer with Busan 5-6 MIL-P-38336 Primer Coating, Inorganic Zinc MoZinc TM 3 Inorganic Zinc Coating 28-DH-50 MIL-C-81309 Corrosion Preventative Compound BLP Lube 60 TM 10-60 Type II, Class 2 MIL-C-83286 * Coating, Urethane, Aliphatic Isocyanate Special Order Only MIL-C-85285 * Coating, Polyurethane, High Solids, Type II Special Order Only 8

SURFACE PREPARATION SPECIFICATIONS SOCIETY FOR PROTECTIVE COATINGS PROPER SURFACE PREPARATION is the key to maximum service from any paint system. The following is a brief summary of the standards published by the Society for Protective Coatings, formerly the Steel Structures Painting Council, 40 24th Street, 6th Floor, Pittsburgh, Pennsylvania 15222-4643. Please refer to the full specification for further information. SSPC-SP 1: SOLVENT CLEANING Solvent Cleaning covers many methods of cleaning, some of which go beyond solvent action and utilize chemical cleaning to remove oil, grease, dirt, soil, drawing compounds and other similar matter. It includes the removal of old paints by the use of paint removers or alkaline paint strippers. Corrosive salts, such as chlorides and sulfates are not removed with hydrocarbons and must be removed with water prior to cleaning the surface with hydrocarbon solvents. This method of cleaning will not remove rust, rust scale, or mill scale. When rags are used for solvent cleaning, they should be changed frequently as they absorb grease and act as a transfer medium for contaminants. Any alkaline compounds should be removed carefully as they may form soap, which will inhibit good adhesion of future coating systems. As a final step for extra protection, the surface should be wiped clean with a weak phosphoric acid solution. Caution should always be taken when using solvent cleaning because of the danger of combustion. SSPC-SP 2: HAND TOOL CLEANING Hand Tool Cleaning is primarily a method for preparing metal surfaces for coating by removing loose mill scale, loose rust and loose paint by hand brushing, sanding, scraping or chipping. Other hand-impact tools or a combination of these methods can be used. This type of cleaning is normally used in preparing surfaces where corrosion is only a minor problem. Care should always be taken on weld seams or spots to remove flux as it promotes premature system failure. Hand cleaning is not recommended for the faster drying finishing systems, such as vinyls. SSPC-SP 3: POWER TOOL CLEANING Power Tool Cleaning is a method of preparing metal surfaces for coating by removing the loose mill scale, loose rust, and loose old paint with power wire brushes, impact tools, grinders, sanders or a combination of the tools. In employing this method, care should be taken that burnished mill scale is not mistaken for bright, clean metal. Primer coatings will not adhere to burnished areas of this type and premature failure results. This system does not intend that tight mill scale, tight rust, and tight paint be removed by this process. Loose mill scale, loose rust, and loose paint, and other detrimental foreign matter present, however, shall be removed. 1

SSPC-SP 5: WHITE METAL BLAST CLEANING White Metal Blast Cleaning is a method of preparing surfaces for coating by removing all mill scale, rust scale, paint, or other foreign matter by the use of abrasive propelled either through nozzles by compressed air or by centrifugal wheels. White Metal is defined as a surface with a gray-white uniform metallic color, slightly roughened to form a suitable anchor pattern for coatings. The surface shall be free of visible mill scale, rust, corrosion, oxide, paint or other foreign matter. The cost of this method is comparatively high and is generally used only when required for top performance of sophisticated coating systems. SSPC-SP 6: COMMERCIAL BLAST CLEANING Commercial Blast Cleaning is a method of preparing surfaces for coating by removing all mill scale, rust scale, paint, or other foreign matter by the use of abrasive propelled either through nozzles by compressed air or by centrifugal wheels. It requires the removal of all visible scale, rust, and other surface contaminants. Evenly dispersed very light shadows, streaks, and discoloration caused by stains of rust, stains of mill scales, and stains of previously applied paint may remain on no more than 33% of the surface. Slight residues of rust and paint may also be left in the craters or pits if the original surface is pitted. SSPC-SP 7: BRUSH-OFF BLAST CLEANING Brush-Off Blast Cleaning is a method of preparing surfaces for coating by removing loose mill scale, loose rust scale, loose paint, or other foreign matter by the use of abrasive propelled either through nozzles by compressed air or by centrifugal wheels. It is not intended that the surface be free of all scale, rust, and paint. The remaining scale, rust, and paint should be tight and the surface should be sufficiently abraded to provide good adhesion and bonding of paint. The low cost of this method may result in economical protection in mild environments. A blast-cleaned surface should be treated or primed before any rusting occurs or the benefit of blast cleaning is lost. The exposed bare metal will rust quickly under conditions of high humidity, when wet, or when in a corrosive atmosphere. It is best practice to prime or chemically treat within eight hours of blasting. SSPC-SP 10: NEAR-WHITE BLAST CLEANING Near-White Blast Cleaning is a method of preparing surfaces for coating by removing nearly all mill scale, rust scale, paint, or other foreign matter by the use of abrasive propelled either through nozzles by compressed air or by centrifugal wheels. A Near-White blast cleaned finish is defined as one from which all oil, grease, dirt, mill scale, rust, corrosion products, oxides, paint or other foreign matter have been completely removed from the surface except for very light shadows, very slight streaks, or slight discoloration caused by rust stain, mill scales oxides, or slight residue of paint or coating that may remain. At least 95% of each square inch of surface shall be free of all visible residues and the remainder shall be limited to the slight discoloration mentioned above. 2

SSPC-SP 11: POWER TOOL CLEANING TO BARE METAL Power Tool Cleaning to Bare Metal is a method of preparing metal surfaces for painting by removing all mill scale, rust scale, paint, or other foreign matter by the use of power tools to produce a bare metal surface and to retain or produce a surface profile. The surface shall be free of visible mill scale, rust, corrosion, oxide, paint or other foreign matter. Slight residues of rust and paint may be left in the lower portions of pits if the original surface is pitted. 3

RECOMMENDED PAINTING SPECIFICATIONS FOR FERROUS METALS For Non-Immersion Service at Ambient Temperatures This section covers ferrous metals, including structural steel, non-galvanized roof decking, exteriors of storage tanks and silos, tubing, pipe racks, platforms, ladders, siding, doors and door frames, both interior and exterior, for non-immersion service at ambient temperatures. Originally written for new industrial construction, the scope has been expanded to include coating systems for commercial, institutional, and residential construction and for maintenance painting, both for recoating original systems and for upgrading deteriorated industrial coating systems where removal of existing coatings is not feasible or practical but high performance is required. Proper surface preparation is essential to the life of any coating system. Abrasive blasting is the preferred method of removing rust and mill scale on new steel and old paint, rust and similar surface contaminants on previously painted steel prior to coating. In addition to cleaning the surface, abrasive blasting cuts the steel to provide an anchor pattern which assures good adhesion of the primer to the substrate. Solvent clean to remove grease, oil and similar contaminants which cannot be removed successfully with abrasive blasting. The Society for Protective Coatings, formerly the Steel Structures Painting Council, is the recognized authority on surface preparation and painting procedures for steel and reference is made to their standards as follows: Solvent Cleaning SSPC-SP 1 Hand Cleaning SSPC-SP 2 Power Tool Cleaning SSPC-SP 3 White Metal Blast SSPC-SP 5 Commercial Blast SSPC-SP 6 Brush-off Blast SSPC-SP 7 Near White Blast SSPC-SP 10 Power Tool Cleaning to Bare Metal SSPC-SP 11 Details will be found in Section 3 of this book, SSPC Standards. Wet blasting is becoming more common to control dust from abrasive blasting and comply with stringent EPA requirements, requiring new techniques and the use of additives to the blasting water to prevent immediate rust bloom. Consult your BLP Mobile Paint representative for equipment and additive recommendations. Ferrous Metals Systems 1

Choice of the coating system will ultimately depend on the surface to be coated, condition of this substrate or of the existing coating and the degree of surface preparation possible, the skill of the applicator and the time available, desired service life of the paint system, and the economic and regulatory factors involved. When specifying coatings, one should always think of the substrate or surface to be painted, surface preparation, pretreatment, shop coat, primer, and intermediate and finish coats as the entire coating system. Please see the FERROUS METALS PRIMER GUIDE for additional primers and shop coats. In new construction, industry practice is to clean and prime structural steel prior to erection. The shop coat or primer selected depends on the finish paint chosen, which is again a function of the service required from the coating system. After erection, all nuts, bolts, scratches and abraded areas should be cleaned and spot-primed before additional coats of primer or finish are applied. Welds should be ground smooth to remove weld splatter before priming. Maintenance painting is the same as for new construction except for surface preparation and spot priming when complete removal of the existing coating system is not contemplated. Maintenance upgrading to high performance coatings is covered at the end of this section. The following sections are listed in order of increasing protection and are intended for non-immersion service at ambient temperatures. SECTION 01. ALKYD SYSTEMS - good protection against normal weathering. Least expensive, easiest surface preparation and application, but shortest service life. May be applied by brush, roller or spray. SECTION 02. ACRYLIC LATEX SYSTEMS - water thinned, may be applied over a variety of primers including alkyd, acrylic, galvanized steel and inorganic zinc. Offers superior resistance to weathering and ultraviolet, good resistance to mild chemical fumes and salt spray. May be applied by brush, roller or spray. SECTION 03. SILICONE ALKYD SYSTEMS - combine ease of surface preparation and application with excellent resistance to weathering and ultraviolet, good resistance to mild chemical fumes and salt spray. Has outstanding gloss and color retention. May be applied by brush, roller or spray over alkyd, silicone alkyd and acrylic primers. SECTION 04. CATALYZED EPOXY AND POLYURETHANES - superior resistance to chemicals, especially alkalis, moisture, and abrasion. Good resistance to most solvents, marine environments, acid splashes. Most epoxies will chalk on exposure to ultraviolet. Topcoat with acrylic epoxy or catalyzed polyurethane to prevent chalking in exterior service. Suitable for immersion service in fresh and salt water. Immersion service is covered separately in sections on Water Storage Tanks and Waste Water Treatment Plants. Recommended for use in industrial and marine service for factories, refineries, tank farms, pipelines, chemical and pharmaceutical plants, waste water treatment plants, and other institutional and commercial applications such as machine shops, schools, hospitals, laundries, kitchens and food processing areas, where a durable, easily-cleaned and attractive finish is desired. Available in high gloss and semi-gloss in a wide range of colors. Waterborne formulations are available. Ferrous Metals Systems 2

SECTION 05 - INORGANIC ZINC-RICH PRIMER SYSTEMS - Excellent galvanic protection in moderate to severe industrial and marine service. See SECTION 04 for high performance topcoats. SECTION 06 - ZINC-RICH EPOXY PRIMER SYSTEMS - Combine the wetting properties, chemical and abrasion resistance of a catalyzed epoxy with the galvanic protections afforded by inorganic zinc. See SECTION 04 for high performance topcoats. SECTION 07 - MAINTENANCE UPGRADE SYSTEMS - For upgrading deteriorated systems.. Mobile Paints offers a wide range of industrial finishes for specialized applications. Please consult your BLP Mobile Paint representative for specific recommendations. Ferrous Metals Systems 3

RECOMMENDED PAINTING SPECIFICATIONS FOR FERROUS METALS For Non-Immersion Service at Ambient Temperatures This section covers ferrous metals, including structural steel, non-galvanized roof decking, tubing,pipe racks, exteriors of storage tanks and silos, platforms, ladders, siding, doors and door frames, both interior and exterior, for non-immersion service at ambient temperatures. Recommended systems include surface preparation, recommended shop coat, and field-applied primers, intermediate and finish coats. Systems have been expanded to include residential, commercial, institutional, light industrial, heavy industrial and marine service as indicated. Additional systems are included for maintenance and upgrading existing deteriorated coatings. Specific applications such as Potable Water Storage Tanks, OEM, Waste Water Treatment Plants, Tank Farms, Food Processing Areas, and Pharmaceutical Plants will be found in their individual sections. Please see the FERROUS METALS PRIMER GUIDE for additional primers and shop coats. In addition to the products listed, Mobile Paints formulates an extensive line of specialty coatings, product finishes, and Federal Specification Paints. Please call your BLP Mobile Paint representative for assistance in meeting your requirements. 1-. SECTION 01 - ALKYD SYSTEMS: 01 ALKYD SYSTEMS offer good protection against normal weathering, mild chemical fumes and normal abrasion. Least expensive, easiest surface preparation and application, shortest service life. Available in a wide range of colors. Not suitable for immersion service. All systems are VOC compliant. Suitable for Interior and Exterior service except as noted. Please see the FERROUS METAL PRIMER GUIDE for additional primers and shop coats. Surface Preparation: Application: Commercial Blast, SSPC-SP 6, recommended Power Tool Clean, SSPC-SP 2, recommended minimum Hand Tool Clean, SSPC-SP 3, minimum acceptable Solvent Clean, SSPC-SP 1, to remove oil or grease Brush, Roller, Airless or Conventional Spray Ferrous Metals Systems 4

01.A Alkyd System, High Gloss, Residential, Commercial & Light Industrial Service Coat Product High Gloss Enamel Finish VOC Sq Ft Mils Shop 9-78 SPEED PRIME Red Oxide Primer 3.76 447 1.5 Prime 10-10 RUS-KIL Metal Primer, Red 3.35 395 2 Intermediate 10-Series RUS-KIL Gloss Enamel 3.35 385 2 Finish 10-Series RUS-KIL Gloss Enamel 3.35 385 2 Total Dry Mils 7.5 01.B Alkyd System, High Gloss, Residential, Commercial & Light Industrial Service Coat Product High Gloss Enamel Finish VOC Sq Ft Mils Shop 9-78 SPEED PRIME Red Oxide Primer 3.76 447 1.5 Prime 10-10 RUS-KIL Metal Primer, Red 3.35 395 2 Intermediate 30-Series NAM-A-LAC Non-Toxic Enamel 3.18 409 1.5 Finish 30-Series NAM-A-LAC Non-Toxic Enamel 3.18 409 1.5 Total Dry Mils 6.5 01.C Alkyd System, Semi-Gloss, Interior, Residential, Commercial & Light Industrial Service Coat Product Semi-Gloss Enamel Finish VOC Sq Ft Mils Shop 9-78 SPEED PRIME Red Oxide Primer 3.76 447 1.5 Prime 10-10 RUS-KIL Metal Primer, Red 3.35 395 2 Intermediate 135-Series COVENTRY Lustarite Satin-Gloss 3.04 427 2 Finish 135-Series COVENTRY Lustarite Satin-Gloss 3.04 427 2 01.D Alkyd System, High Gloss, Industrial Service Total Dry Mils 7.5 Coat Product High Gloss Enamel Finish VOC Sq Ft Mils Shop 28-DR-154 MO-BAR Universal LCF Primer 4.50 379 1.5 Prime 28-DR-160 MO-BAR PM-III LCF Universal Primer 3.49 387 2 Intermediate 10-Series RUS-KIL Gloss Enamel 3.35 385 2 Finish 10-Series RUS-KIL Gloss Enamel 3.35 385 2 Total Dry Mils 7.5 Ferrous Metals Systems 5

01.E Alkyd System, Spray Fog Dry Semi-Gloss, Interior, Commercial & Industrial Service Coat Product Semi-Gloss Enamel Finish VOC Sq Ft Mils Shop 9-78 SPEED PRIME Red Oxide Primer 3.76 447 1.5 Prime 10-9 RUS-KIL Metal Primer, Gray 3.35 395 2 Intermediate* 61-BW-2 SPRAY FOG DRY Semi-Gloss Coating 3.25 382 2 Finish* 61-BW-2 SPRAY FOG DRY Semi-Gloss Coating 3.25 382 2 * Apply by airless spray Total Dry Mils 7.5 01.F Alkyd System, Spray Fog Dry Flat, Interior, Commercial & Industrial Service Coat Product Flat Enamel Finish VOC Sq Ft Mils Shop 9-78 SPEED PRIME Red Oxide Primer 3.76 447 1.5 Prime 10-9 RUS-KIL Metal Primer, Gray 3.35 395 2 Intermediate* 6-DW-58 SPRAY FOG DRY Flat Coating 3.17 407 2 Finish* 6-DW-58 SPRAY FOG DRY Flat Coating 3.17 407 2 * Apply by airless spray Total Dry Mils 7.5 SECTION 02 - ACRYLIC LATEX ENAMEL SYSTEMS: 02 ACRYLIC LATEX ENAMELS are the latest development in a general purpose finish for interior and exterior service. Lead, chromate and mercury free. Very low VOC. Easy to apply over a variety of primers and substrates including zinc and galvanized metals. Good resistance to normal weathering and mild chemical fumes. Waterborne, low odor, easy cleanup. Not for immersion service. Please see the FERROUS METAL PRIMER GUIDE for additional primers and shop coats. Surface Preparation: Application: Commercial Blast, SSPC-SP 6, preferred Power Tool Clean, SSPC-SP 2, recommended minimum Hand Tool Clean, SSPC-SP 3, minimum acceptable Solvent Clean, SSPC-SP 1, to remove oil or grease Brush, Roller, Airless or Conventional Spray Ferrous Metals Systems 6

02.A Acrylic Latex DTM System, High Gloss, Residential to Light Industrial Service Coat Product Acrylic Gloss DTM Enamel Finish VOC Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 310-Series H2O RUS-KIL Acrylic DTM Enamel 1.09 295 2 Finish 310-Series H2O RUS-KIL Acrylic DTM Enamel 1.09 295 2 Total Dry Mils 8.0 02.B Acrylic Latex System, High Gloss, Residential to Light Industrial Service Coat Product Acrylic Gloss Enamel Finish VOC Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 330-Series ACR-A-LAC Acrylic Gloss Enamel 2.11 293 2 Finish 330-Series ACR-A-LAC Acrylic Gloss Enamel 2.11 293 2 Total Dry Mils 8.0 02.C Acrylic Latex System, Medium Gloss, Residential to Light Industrial Service Coat Product Acrylic Gloss Enamel Finish Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 140-Series WEATHER-TITE 100% Acrylic Gloss 1.99 296 2 Finish 140-Series WEATHER-TITE 100% Acrylic Gloss 1.99 296 2 Total Dry Mils 8.0 02.D Acrylic Latex System, Satin Gloss, Residential to Light Industrial Service Coat Product Acrylic Satin Gloss Enamel Finish VOC Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 240-Series WEATHER-TITE 100% Acrylic Satin 2.19 271 2 Finish 240-Series WEATHER-TITE 100% Acrylic Satin 2.19 271 2 Total Dry Mils 8.0 Ferrous Metals Systems 7

02.E Acrylic Latex System, Flat, Residential to Light Industrial Service Coat Product Acrylic Flat Finish VOC Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 40-Series WEATHER-TITE 100% Acrylic Flat 1.03 291 2 Finish 40-Series WEATHER-TITE 100% Acrylic Flat 1.03 291 2 Total Dry Mils 8.0 02.F Vinyl Latex System, Interior, Flat, Residential to Light Industrial Service Coat Product Latex Flat Finish VOC Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 35-Series COVENTRY Interior Latex Flat 0.83 375 1.5 Finish 35-Series COVENTRY Interior Latex Flat 0.83 375 1.5 Total Dry Mils 7.0 02.G Acrylic Latex System, Interior, Semi-Gloss, Residential to Light Industrial Service Coat Product Acrylic Semi-Gloss Enamel Finish VOC Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 1335-Series COVENTRY Acrylic Latex Semi-Gloss 2.00 345 1.5 Finish 1335-Series COVENTRY Acrylic Latex Semi-Gloss 2.00 345 1.5 Total Dry Mils 7.0 02.H Acrylic Latex System, Interior, Eggshell, Residential to Light Industrial Service Coat Product Acrylic Eggshell Enamel Finish VOC Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 2335-Series COVENTRY Acrylic Eggshell Enamel 0.86 375 1.5 Finish 2335-Series COVENTRY Acrylic Eggshell Enamel 0.86 375 1.5 Total Dry Mils 7.0 Ferrous Metals Systems 8

02.I Acrylic Latex System, Interior, High Gloss, Residential to Light Industrial Service Coat Product Acrylic High Gloss Enamel Finish VOC Sq Ft Mils Shop 310-09 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-09 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 335-Series COVENTRY Acrylic High Gloss Enamel 1.09 408 1.5 Finish 335-Series COVENTRY Acrylic High Gloss Enamel 1.09 408 1.5 Total Dry Mils 7.0 02.J Acrylic Latex System, Interior, Fog Dry, Flat, Commercial to Light Industrial Service Coat Product Acrylic Flat Enamel Finish VOC Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 3.35 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 3.35 345 2 Intermediate* 55-DW-3 SPRAY Fog Dry Acrylic Flat White 0.80 322 2 Finish* 55-DW-3 SPRAY Fog Dry Acrylic Flat White 0.80 322 2 *Apply by airless spray Total Dry Mils 8.0 02.K Acrylic Latex System, Interior, Fog Dry, Gloss, Commercial to Light Industrial Service Coat Product Acrylic Gloss Enamel Finish VOC Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 3.35 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 3.35 345 2 Intermediate* 55-AW-9 SPRAY Fog Dry Acrylic Gloss White 0.75 289 2 Finish* 55-AW-9 SPRAY Fog Dry Acrylic Gloss White 0.75 289 2 *Apply by airless spray Total Dry Mils 8.0 Ferrous Metals Systems 9

SECTION 03 - SILICONE ALKYD SYSTEMS: 03 SILICONE ALKYDS offer excellent resistance to marine and industrial environments, weathering and ultraviolet exposure. Good resistance to mild chemical fumes, outstanding gloss and color retention. Easy to apply. Not for immersion service.lead, chromate and mercury free. Please see the FERROUS METAL PRIMER GUIDE for additional primers and shop coats. Surface Preparation: Application: Commercial Blast, SSPC-SP 6, recommended Power Tool Clean, SSPC-SP 2, recommended minimum Hand Tool Clean, SSPC-SP 3, minimum acceptable Solvent Clean, SSPC-SP 1, to remove oil or grease Brush, Roller, Airless or Conventional Spray 03.A Silicone Alkyd System, High Gloss, Residential, Commercial & Industrial Service Coat Product High Gloss Silicone Alkyd Enamel VOC Sq Ft Mils Shop 9-78 SPEED PRIME Red Oxide Primer 3.76 447 1.5 Prime 10-10 RUS-KIL Metal Primer, Red 3.35 395 2 Intermediate 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.5 Finish 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.5 Total Dry Mils 6.5 03.B Silicone Alkyd System, High Gloss, Heavy Industrial & Marine Service Coat Product High Gloss Silicone Alkyd Enamel VOC Sq Ft Mils Shop 28-DR-160 MO-BAR PR-III Universal Primer 3.49 387 2 Prime 28-DR-160 MO-BAR PR-III Universal Primer 3.49 387 2 Intermediate 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.5 Finish 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.5 Total Dry Mils 7.0 Ferrous Metals Systems 10

SECTION 04 - CATALYZED EPOXY AND POLYURETHANE SYSTEMS: 04 CATALYZED EPOXY AND POLYURETHANE SYSTEMS offer superior resistance to many chemicals, especially alkalis, abrasion and moisture, together with good resistance to most solvents, acid splashes and chemical fumes. Recommended for Commercial, Light Industrial, heavy Industrial, and Marine Service at ambient temperatures. Excellent for interior use in chemical and pharmaceutical plants, schools, hospitals, kitchens and food processing areas, laundries, and other institutional, industrial and commercial installations where maximum protection and durability are required. Available in a wide range of colors for an easily cleaned and attractive finish. While most epoxies have excellent resistance to fresh and salt water, immersion service is covered in separate sections under Water Storage Tanks and Sewage Treatment Plants. Waterborne epoxies are offered but should not be used in immersion service. Epoxy mastics are generally surface tolerant and suitable both as primers for sandblasted steel and for application over ferrous metal surfaces where optimum surface preparation may not be feasible. Also recommended as a sealer / barrier coat over existing deterioratedcoatings to allow upgrading to high performance systems such as epoxies and polyurethanes. The following epoxy primers and epoxy-mastics are available and may be interchanged within the suggested system recommendations. Topcoat with catalyzed polyurethane or acrylic epoxy to prevent chalking in exterior service. Code Description VOC Sq Ft DFT /Gal 40-DR-5 MOPOXY HB Epoxy Primer, Red 3.49 131 6.0 513-10 MOPOXY Epoxy Primer, Red 4.24 322 2.0 613-10 MOPOXY HS Epoxy Primer, Red 2.00 382 3 41-Series MOPOXY IR (Indefinate Recoat) DTM Mastic 2.29 136 8 40-AY-2 MOPOXY MASTIC Aluminum 0.51 248 6 40-AW-32 MOPOXY MASTIC White 1.30 217 6 40-AH-51 MOPOXY MASTIC Gray 1.30 217 6 41-Series MOPOXY PLUS High Solids Mastic 2.36 131 8 41-AF-2 MOPOXY PRE-PREP Penetrating Sealer 0.00 1604 1 40-DR-12 MOPOXY PCP Preconstruction Primer 5.25 388 1 The following Coal Tar epoxies are generally used in immersion or underground service and are not topcoated. 40-AX-7 MO-TAR C-200 Polyamide Coal Tar 1.56 157 8 40-BX-6 MO-TAR HB-90 High Build Coal Tar 1.13 67 20 Please review our FERROUS METAL PRIMER GUIDE for additional detail. CATALYZED POLYURETHANES offer good outstanding color and gloss retention. Recommended for marine environments, tank farms, chemical plants, and heavy equipment. Not recommended for immersion service. Ferrous Metals Systems 11

The following catalyzed polyurethane formulations are available and may be used interchangeably within the suggested system recommendations. Other formulations are available for special service. Code Description VOC Sq Ft DFT /Gal 72-Series MOTHANE Polyurethane Enamel 4.11 339 2 Apply by Airless or Conventional Spray only 72-Series MOTHANE HD (Heavy Duty) Polyurethane 4.11 268 2.5 Apply by Airless or Conventional Spray, Brush or Roll 72-Series MOTHANE HS-1000 (High Solids) Polyurethane 2.45 513 2 Apply by Airless or Conventional Spray, Brush or Roll 72-Series MOTHANE HS-900 (High Solids) Polyurethane 2.47 417 2.5 Apply by Airless or Conventional Spray only Mobile Paints offers a wide range of epoxies and polyurethanes for special applications. Ask your BLP Mobile Paint representative for detailed recommendations. Please see the FERROUS METAL PRIMER GUIDE for additional primers and shop coats. Surface Preparation: Application: Commercial Blast, SSPC-SP 6, preferred minimum Power Tool Clean, SSPC-SP 2, minimum acceptable Solvent Clean, SSPC-SP 1, to remove oil or grease Brush, Roller, Airless or Conventional Spray unless otherwise indicated 04.A Catalyzed Water-Borne Acrylic Epoxy, Commercial & Light Industrial Service Coat Product High Gloss W/B Catalyzed Acrylic VOC Sq Ft Mils Shop 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 69-AW-5 MOPOXY H2O-100 W/B Acrylic Epoxy 1.71 313 2 Finish 69-AW-5 MOPOXY H2O-100 W/B Acrylic Epoxy 1.71 313 2 Total Dry Mils 8.0 Ferrous Metals Systems 12

04.B Catalyzed Water-Borne Epoxy System, Commercial & Industrial Service Coat Product Semi-Gloss W/B Amide Epoxy Finish VOC Sq Ft Mils Shop 69-DR-1* MOPOXY H2O Polyamide Metal Primer 0.89 257 3 Prime 69-DR-1* MOPOXY H2O Polyamide Metal Primer 0.89 257 3 Intermediate 69-AW-6 MOPOXY H2O-200 W/B Amide Epoxy 1.00 225 3 Finish 69-AW-6 MOPOXY H2O-200 W/B Amide Epoxy 1.00 225 3 * May also use 310-9 H2O RUS-KIL Primer Total Dry Mils 12.0 04.C Catalyzed Epoxy System, Commercial & Industrial Service Coat Product High Gloss Epoxy Finish VOC Sq Ft Mils Shop 40-DR-12 MOPOXY PCP Preconstruction 5.25 348 1 Prime 513-10 MOPOXY Metal Primer 4.24 322 2 Intermediate 513-Line MOPOXY High* Gloss Epoxy Coating 4.30 314 2 Finish 513-Line MOPOXY High* Gloss Epoxy Coating 4.30 314 2 * use catalyst 77-17 for semi-gloss Total Dry Mils 7.0 04.D Catalyzed Epoxy System, Commercial & Industrial Service Coat Product High Solids Semi-Gloss Epoxy Finish VOC Sq Ft Mils Shop 40-DR-12 MOPOXY PCP Preconstruction 5.25 348 1 Prime 613-10 MOPOXY HS High Solids Metal Primer 2.00 382 3 Intermediate 613-line MOPOXY HS High Solids S/G Epoxy 2.00 374 3 Finish 613-line MOPOXY HS High Solids S/G Epoxy 2.00 374 3 Total Dry Mils 10.0 04.E Catalyzed Epoxy System, Commercial & Industrial Service Coat Product Acrylic Epoxy High Gloss Finish VOC Sq Ft Mils Shop 40-DR-12 MOPOXY PCP Preconstruction 5.25 348 1 Prime 613-10 MOPOXY HS High Solids Metal Primer 2.00 382 3 Intermediate 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 8.0 Ferrous Metals Systems 13

04.F Catalyzed Epoxy / Epoxy Mastic / Polyurethane System, Heavy Industrial & Marine Service Coat Product High Gloss Polyurethane Finish VOC Sq Ft Mils Prime 613-10 MOPOXY HS High Solids Metal Primer 2.00 382 3 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6 Finish 72-Series MOTHANE HD Polyurethane 4.11 268 2.5 Finish 72-Series MOTHANE HD Polyurethane 4.11 268 2.5 Total Dry Mils 14.0 04.G Catalyzed Epoxy / Epoxy Mastic / Polyurethane System, Heavy Industrial & Marine Service Coat Product High Gloss Polyurethane Finish VOC Sq Ft Mils Prime 613-10 MOPOXY HS High Solids Metal Primer 2.00 382 3 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 13.0 All of the below are high-solids, low VOC and may be used interchangeably as Primer and Intermediate coats in the following systems. All may be topcoated with either catalyzed epoxy or polyurethane for maximum protection in heavy industrial and marine environments. MOPOXY MASTIC is a high solids, high build, surface tolerant amine epoxy formulated for application over sound rust and/ or deteriorated paint systems as a base coat for upgrading to high performance coatings such as acrylic epoxies and polyurethanes. Superior performance over abrasive blasted steel in heavy industrial and marine environments. Excellent resistance to fresh and salt water, most organic solvents, chemical splashes and fumes, and abrasion. MOPOXY PLUS is a high-performance, high solids DTM polyamide epoxy with excellent adhesion to tight rust, good adhesion to damp surfaces, and cures at low temperatures. Excellent resistance to fresh and salt water, detergents and corrosive chemicals. Very good resistance to fumes and spills of most organic solvents, acids, and alkalis. Superior performance over blast cleaned steel. MOPOXY IR - Indefinite Recoatability Epoxy - is a high-solids, high-build, surface tolerant, DMTpolyamide coating which may be applied to damp, rusty surfaces, allowed to dry for prolonged periods, then topcoated with other epoxies or polyurethanes without loss of intercoat adhesion. Good anticorrosive properties. Solvent sensitive. Superior anticorrosive properties over blast-cleaned steel. Ferrous Metals Systems 14

04.H Catalyzed Epoxy Mastic /Epoxy System, Heavy Industrial & Marine Service Coat Product High Gloss Epoxy Finish VOC Sq Ft Mils Prime 40-AH-51 MOPOXY Mastic, Dawn Gray 1.30 217 6 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6 Finish 513-Line MOPOXY High* Gloss Epoxy Coating 4.30 314 2 Finish 513-Line MOPOXY High* Gloss Epoxy Coating 4.30 314 2 * use catalyst 77-17 for semi-gloss Total Dry Mils 16.0 04.I Catalyzed Epoxy Mastic /Epoxy System, Heavy Industrial & Marine Service Coat Product High Solids Semi-Gloss Epoxy Finish VOC Sq Ft Mils Prime 40-AH-51 MOPOXY Mastic, Dawn Gray 1.30 217 6 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6 Finish 613-line MOPOXY HS High Solids Epoxy 2.00 374 3 Finish 613-line MOPOXY HS High Solids Epoxy 2.00 374 3 Total Dry Mils 18.0 04.J Catalyzed Epoxy Mastic /Acrylic Epoxy System, Heavy Industrial & Marine Service Coat Product High Gloss Acrylic Epoxy Finish VOC Sq Ft Mils Prime 40-AH-51 MOPOXY Mastic, Dawn Gray 1.30 217 6 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 16.0 Ferrous Metals Systems 15

04.K Catalyzed Epoxy Mastic /Polyurethane System, Very Heavy Industrial & Marine Service Coat Product High Gloss Polyurethane Finish VOC Sq Ft Mils Prime 40-AH-51 MOPOXY Mastic, Dawn Gray 1.30 217 6 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6 Finish 72-Series MOTHANE HD Polyurethane 4.11 268 2.5 Finish 72-Series MOTHANE HD Polyurethane 4.11 268 2.5 Total Dry Mils 17.0 04.L Catalyzed Epoxy Mastic /Polyurethane System, Very Heavy Industrial & Marine Service Coat Product High Solids Polyurethane Finish VOC Sq Ft Mils Prime 40-AY-2 MOPOXY Mastic, Aluminum 0.51 248 6 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 16.0 04.M Catalyzed Epoxy Mastic /Acrylic Epoxy System, Heavy Industrial & Marine Service Coat Product Acrylic Epoxy Gloss Finish VOC Sq Ft Mils Prime 41-CW-1 MOPOXY-PLUS DTM Epoxy 2.36 131 8 Intermediate 41-CW-1 MOPOXY-PLUS DTM Epoxy 2.36 131 8 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 20.0 Ferrous Metals Systems 16

04.N Catalyzed DTM Epoxy Mastic /Polyurethane System, Heavy Industrial & Marine Service Coat Product High Solids Polyurethane Finish VOC Sq Ft Mils Prime 41-CW-1 MOPOXY-PLUS DTM Epoxy 2.36 131 8 Intermediate 41-CW-1 MOPOXY-PLUS DTM Epoxy 2.36 131 8 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 20.0 04.O Indefinitely Recoatable Epoxy/Polyurethane System, Heavy Industrial & Marine Service Coat Product High Gloss Acrylic Epoxy Finish VOC Sq Ft Mils Prime 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Intermediate 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 20.0 04.P Recoatable Epoxy/Polyurethane System, Heavy Industrial & Marine Service Coat Product High Solids Polyurethane Finish VOC Sq Ft Mils Prime 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Intermediate 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 20.0 Ferrous Metals Systems 17

SECTION 05 - INORGANIC ZINC-RICH PRIMER SYSTEMS: 05 INORGANIC ZINC-RICH PRIMERS offer excellent galvanic protection in moderate to severe industrial and marine environments. Excellent resistance to fresh and salt water, detergents, and most chemicals, moisture and abrasion. High performance topcoats are recommended for severe chemical exposures. Heat resistant to 750 degrees Fahrenheit. Recommended for tank farms, pipe racks, in heavy industrial or marine service. Inorganic zinc requires a clean surface and good anchor pattern for good adhesion. Surface Preparation: Application: White Metal Sandblast, SSPC-SP-5, preferred Commercial Sandblast, SSPC-SP 6, minimum acceptable Airless or Conventional Spray with constant mechanical agitation Inorganic Zinc is much more porous than hot-dip galvanizing and may be top-coated without application of vinyl wash primer. See Galvanized Metals & Aluminum for details. Top-coat Application: Apply mist coat to wet zinc thoroughly to dispel air and avoid bubbles. Follow by full body coat while still tacky, 05.A Inorganic Zinc/Epoxy Mastic/Polyurethane System, Very Heavy Industrial & Marine Service Recommended for tank farms, pipe racks, in heavy industrial or marine service. Coat Product High Gloss Polyurethane Finish VOC Sq Ft Mils Prime 28-DH-50 MO-ZINC #3 Inorganic Zinc Primer 3.88 342 3 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 13.0 05.B Inorganic Zinc/Epoxy Mastic/Epoxy System, Heavy Industrial & Marine Service Coat Product High solids Semi-Gloss Epoxy Finish VOC Sq Ft Mils Prime 28-DH-50 MO-ZINC #3 Inorganic Zinc Primer 3.88 342 3 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 613-Series MOPOXY HS High Solids Epoxy 2.00 374 3 Finish 613-Series MOPOXY HS High Solids Epoxy 2.00 374 3 Total Dry Mils 15.0 Ferrous Metals Systems 18

05.C Inorganic Zinc/Epoxy Mastic/Epoxy System, Heavy Industrial & Marine Service Coat Product Acrylic Epoxy Gloss Finish VOC Sq Ft Mils Prime 28-DH-50 MO-ZINC #3 Inorganic Zinc Primer 3.88 342 3 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 13.0 SECTION 06 - ZINC-RICH EPOXY PRIMER SYSTEMS: 06 ZINC-RICH EPOXY PRIMER combines the wetting properties, chemical and abrasion resistance of a catalyzed epoxy with the galvanic protection afforded by inorganic zinc. Excellent resistance to fresh and salt water, detergents and most chemicals, abrasion and moisture. Excellent for touch-up of inorganic zinc primers. VOC Compliant. Recommended for tank farms, pipe rack, severe industrial and marine environments. Topcoat recommended for severe exposures. Surface Preparation: Application: Near-White Metal Blast, SSPC-SP10, recommended Commercial Sandblast, SSPC-SP 6, recommended minimum Power Tool Clean, SSPC-SP 2, minimum acceptable Airless or Conventional Spray with continual mechanical agitation. The following zinc-rich epoxy primers are available and may be used interchangeably: Code Description VOC Sq Ft Mils 40-CM-2 MOPOXY ZR Zinc Rich Primer 3.45 321 2.5 40-CM-4 MOPOXY ZR Zinc Rich Primer, Green 3.89 257 3.5 40-DH-6 MIL-DTL-24441 F 159 ZR Primer 2.50 336 3.0 In the interest of simplicity, we have written the following recommendations based on the application of 40-CM-2 because of its low VOC and very high zinc content in the dry film. Please see the FERROUS METAL PRIMER GUIDE for additional primers and shop coats. Ask your BLP Mobile Paint representative for detailed recommendations. Ferrous Metals Systems 19

06.A Zinc-Rich Epoxy/Epoxy/Polyurethane System, Very Heavy Industrial & Marine Service Recommended for tank farms, pipe rack, severe industrial and marine environments. Coat Product High Gloss Polyurethane Finish VOC Sq Ft Mils Prime 40-CM-2 MOPOXY ZR Zinc Rich Epoxy Primer 3.45 321 2.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 12.5 06.B Zinc-Rich Epoxy/Epoxy Mastic/Epoxy System, Heavy Industrial & Marine Service Coat Product High Solids Semi-Gloss Epoxy Finish VOC Sq Ft Mils Prime 40-CM-2 MOPOXY ZR Zinc Rich Epoxy Primer 3.45 321 2.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 613-Series MOPOXY HS High Solids Epoxy 2.00 374 3 Finish 613-Series MOPOXY HS High Solids Epoxy 2.00 374 3 Total Dry Mils 14.5 06.C Zinc-Rich Epoxy/Epoxy Mastic/Acrylic Epoxy, Heavy Industrial & Marine Service Coat Product High Solids Semi-Gloss Epoxy Finish VOC Sq Ft Mils Prime 40-CM-2 MOPOXY ZR Zinc Rich Epoxy Primer 3.45 321 2.5 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 12.5 Ferrous Metals Systems 20

SECTION 07 - MAINTENANCE UPGRADE SYSTEMS: 07 FOR UPGRADING deteriorated alkyd, silicone alkyd and acrylic finishes and repairing catalyzed epoxy and polyurethane systems where removal of existing coatings is not possible. See Section 04, Catalyzed Epoxy and Polyurethane Systems, for additional coatings. MOPOXY MASTIC Aluminum is a very high solids, low VOC, surface tolerant high performance epoxy coating offering excellent protection in moderate to severe industrial and marine environments. DTM or use as base coating over rust and deteriorated paint for upgrading to high performance topcoats. MOPOXY MASTIC is a high-solids, high-build, surface tolerant amine epoxy formulated for application over sound rust and/or deteriorated paint systems as a base coat for upgrading to high performance coatings such as acrylic epoxies and polyurethanes. MOPOXY IR, Indefinite Recoatablility Epoxy, is a high-solids, surface-tolerant, high-build polyamide coating which may be applied to damp, rusty surfaces, allowed to dry for prolonged periods, then topcoated with other epoxies or polyurethanes without loss of intercoat adhesion. Good anticorrosive properties. MOPOXY PLUS is a high-performance high-solids DTM polyamide epoxy with excellent adhesion to tight rust, good adhesion to damp surfaces, and cures at low temperatures. Excellent resistance to fresh and salt water, detergents and corrosive chemicals. Very good resistance to fumes and spills of most organic solvents, acids and alkalis. MOPOXY PRE-PREP is a 100% solids epoxy with very low viscosity and excellent substrate wetting properties. Excellent for badly rusted areas where sandblasting and removal of existing coatings is not possible and only minimal cleaning is possible. Penetrates and bonds rust and deteriorated coatings into a solid film which seals out moisture and oxygen. Allow to cure for 24 hours, then apply recommended intermediate coat while still slightly soft. Will accept a wide variety of coatings. MO-BAR Universal Primer is a high-quality, quick-drying modified alkyd anticorrosive primer or shop coat. Use as a barrier coat to prevent lifting of solvent-sensitive coatings by high performance top coats. Excellent protection against corrosion in mild industrial and marine environments. All systems recommended are suitable for heavy industrial and marine service. Surface Preparation: Application: Pressure Wash (3,000 psi or better) to remove contamination Solvent Clean, SSPC-SP 1, to remove oil and grease Power Tool Clean, SSPC-SP 2, preferred Hand Tool Clean, SSPC-SP 3, minimum recommended Brush, roller or airless or conventional spray. Ferrous Metals Systems 21

07.A Epoxy Mastic / High Solids Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq Ft Mils Spot Prime 40-AY-2 MOPOXY MASTIC, Aluminum 0.51 248 6 Prime 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 16.0 07.B Epoxy Mastic / Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq Ft Mils Spot Prime 40-AY-2 MOPOXY MASTIC, Aluminum 0.51 248 6 Prime 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 16.0 07.C IR Epoxy / High Solids Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq Ft Mils Spot Prime 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Prime 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 20.0 07.D IR Epoxy / Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq Ft Mils Spot Prime 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Prime 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 20.0 Ferrous Metals Systems 22

07-E Low Viscosity Epoxy / Epoxy Mastic / High Solids Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq Ft Mils Prime 41-AF-2 MOPOXY PrePrep Clear 0.00 1069 1.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 11.5 07-F Low Viscosity Epoxy / Epoxy Mastic / Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq Ft Mils Prime 41-AF-2 MOPOXY PrePrep Clear 0.00 1069 1.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 11.5 07-G Universal Primer / Epoxy Mastic / High Solids Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq Ft Mils Prime 28-DR-160 MO-BAR PM-III Universal Primer 3.49 393 1.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 11.5 07-H Universal Primer / Epoxy Mastic / Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq Ft Mils Prime 28-DR-160 MO-BAR PM-III Universal Primer 3.49 393 1.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 11.5 Ferrous Metals Systems 23

FERROUS METAL PRIMER GUIDE INDEX Overview of Anticorrosive Metal Primers Section 1 - Alkyd Primers for Ferrous Metals 1.a MO-BAR Universal Primers 1.b QD QUICK DRY Metal Primers 1.c FD FAST DRY Metal Primers 1.d Miscellaneous Specialty Items Section 2 - Waterborne Metal Primers 2.a Waterborne Acrylic Metal Primers 2.b Waterborne Alkyd Metal Primers 2.c Waterborne Epoxy Metal Primers Section 3 - Zinc Rich Metal Primers 3.a Inorganic Zinc-Rich Primers 3.b Organic Zinc-Rich Epoxy Primers Section 4 - Epoxy Primers for Ferrous Metals 4.a MoPoxY Catalyzed Epoxy Metal Primers 4.b MoPoxY DTM Primers & Intermediate Coats Section 5 - Coal Tar Epoxies 5.a MO-TAR Coal Tar Epoxy Ferrous Metals Systems - Primer Guide 1

FERROUS METAL PRIMER GUIDE This Guide is intended to show a representative selection of the Ferrous Metal Primers and Shop Coats formulated by Mobile Paints. In addition, we offer an extensive selection of products for OEM, Federal Specification and Navy Formulas, product finishes, and private labels. Please contact our home office for your specific requirements. Section 1 ALKYD PRIMERS FOR FERROUS METALS 1.a MOBAR UNIVERSAL PRIMER MO-BAR Universal Primer: A high-quality, quick-drying phenolic-modified alkyd universal anticorrosive primer or shop coat. Use as barrier coat to prevent lifting of existing solvent-sensitive coatings by high performance top coats. Excellent protection against corrosion in mild industrial and marine environments. Recoat time between 1 and 4 hours except under high performance top coats when longer cure may be required. Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle To Recoat 28-DR-164 MO-BAR 3.5 VOC Universal Primer, LCF, Red 3.40 1.5 535 15 min 1 hr 3 hrs 28-DH-93 MO-BAR PM-III Univeral Primer, LCF, Gray 3.49 2 387 10 min 20 min 4 hrs 28-DR-160 MO-BAR PM-III Universal Primer, LCF, Red 3.49 2 387 10 min 20 min 4 hrs 28-DH-95 MO-BAR PM-II Universal Primer, Gray 4.30 1.5 393 15 min 1 hr 3 hrs 28-DR-145 MO-BAR PM-II Universal Primer, Red 4.30 1.5 393 15 min 1 hr 3 hrs 28-DW-13 MO-BAR PM-II Universal Primer, White 4.30 1.5 393 15 min 1 hr 3 hrs 28-DH-37 MO-BAR Universal Primer, Gray 4.50 1.5 382 5 min 15 min 1 hr 28-DR-105 MO-BAR Universal Primer, Red 4.50 1.5 382 5min 15 min 1 hr 28-DW-12 MO-BAR Universal Primer, White 4.50 1.5 382 5 min 15 min 1 hr 28-DH-83 MO-BAR Universal Primer, LCF, Gray 4.50 1.5 379 5 min 15 min 1 hr 28-DR-154 MO-BAR Universal Primer, LCF, Red 4.50 1.5 379 5 min 15 min 1 hr Ferrous Metals Systems - Primer Guide 2

1.b QD QUICK DRY METAL PRIMERS QD QUICK-DRY: Modified alkyd anticorrosive primers for service as primer or shopcoat. Excellent protection against corrosion in mild industrial and marine environments. Very fast dry time allows short recoat period between 1 to 4 hours. Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle ToRecoat 28-DH-97 HS Hi-Solids Primer, LCF, Gray 2.95 2 375 15 min 1 hr 3 hrs 28-DH-117 HS High Solids Primer, LCF, Gray 3.10 1 372 10 min 1 hr 4 hrs 28-DH-84 SPEED PRIME 10 QD Primer, LCF, Gray 3.50 1 522 15 min 30 min 1 hr 28-DH-75 QD-58 Quick Dry LCF Primer, Gray 4.15 2 320 10 min 30 min 1 hr 28-DR-134 QD-58 Quick Dry LCF Primer, Red 4.15 2 320 10 min 30 min 1 hr 28-DH-64 QD-Lead Free Primer, LCF, Blue Gray 4.20 2 319 10 min 30 min 1 hr 28-DR-126 Fast Dry Primer, LCF, Red 4.25 1.5 400 30 min 1 hr 2 hrs 28-DH-73 SPEED PRIME II Zinc Chromate, Gray 4.29 1.5 349 15 min 30 min 4 hrs 28-DR-127 SPEED PRIME II Zinc Chromate, Red 4.29 1.5 349 15 min 30 min 4 hrs 1.c FD FAST DRY METAL PRIMERS FD FAST-DRY: Modified alkyd anticorrosive primers or shopcoats. Offer excellent protection against corrosion in mild industrial and marine environments. Average recoat time of 8 to 24 hours. Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle To Recoat 28-DH-74 SPEED PRIME HS High Solids ZC, Gray 2.56 2 482 30 min 2 hrs 12 hrs 28-DR-136 SPEED PRIME HS High Solids ZC, Red 2.56 2 482 30 min 2 hrs 12 hrs 28-DR-166 SPEED PRIME HS LCF Red Primer 2.70 2 461 30 min 2 hrs 12 hrs 28-DH-97 High Solids LCF Primer, Gray 2.95 2 375 30 min 2 hrs 12 hrs 28-DR-147 High Solids LCF Red Oxide 3.25 2 417 30 min 1 hr 8 hrs 10-5 RUS-KIL Rust Inhibiting Primer, LCF, White 3.35 2 395 2 hrs 4 hrs 24 hrs 10-9 RUS-KIL Rust Inhibiting Primer, LCF, Gray 3.35 2 395 2 hrs 4 hrs 24 hrs 10-10 RUS-KIL Rust Inhibiting Primer, LCF, Red 3.35 2 395 2 hrs 4 hrs 24 hrs 521-5 QD-521 Quick Dry Primer, White 3.50 1.5 556 1 hr 4 hrs 12 hrs 521-8 QD-521 Quick Dry Primer, Gray 3.50 1.5 556 1 hr 4 hrs 12 hrs 521-10 QD-521 Quick Dry Primer, Red 3.50 1.5 556 1 hr 4 hrs 12 hrs 9-78 SPEED PRIME Red Oxide Primer, LCF 3.76 1.5 447 45 min 2 hrs 8 hrs 520-8 520-10 QD-520 Quick Dry Primer, Gray (OEM) QD-520 Quick Dry Primer, Red (OEM) 3.91 3.91 1.5 1.5 450 450 1 hr 1 hr 2 hr 2 hr 8 hrs 8 hrs 520-5 QD-520 Quick Dry Primer, White (OEM) 4.31 1.5 389 1 hr 2 hr 8 hrs Ferrous Metals Systems - Primer Guide 3

1.d MISCELLANEOUS SPECIALTY ITEMS Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle To Recoat 80439 DOD-P-21035B Galvanizing Repair 2.46 2 532 30 min 8 hrs max 8 hrs 409-68 Jack Tar Phenolic A/C ZC Primer, Brown 2.81 6 310 20 min 3 hrs 16 hrs 10-7 RUS-KIL Brite Galvanizing Coating 4.17 1 666 15 min 45 min 3 hrs 10-8 RUS-KIL Cold Galvanizing Coating 4.13 1 666 15 min 45 min 3 hrs 80242 TT-P-645B Zinc Molybdate Yellow (LCF) 2.83 1.5 595 4-6 hrs 6-8 hrs 9-42 VINYL Wash Primer 6.04 0.5 252 5 min 15 min 30 min Section 2 WATERBORNE METAL PRIMERS 2.a WATERBORNE ACRYLIC METAL PRIMERS High performance, water-reducible acrylic latex corrosion-inhibiting primers for ferrous metal, galvanized metal, and aluminum. Excellent adhesion, flexibility, blister resistance and mild chemical resistance. Excellent protection in mild industrial and marine exposures. Use as primer or shop coat. Lead-free, chromate-free, mercury-free, low VOC. Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle To Recoat 310-6 H2O RUS-KIL Primer, LCF, White 1.14 2 345 1 hr 4 hrs 4 hrs 310-8 H2O RUS-KIL Primer, LCF, Gray 1.14 2 345 1 hr 4 hrs 4 hrs 310-9 H2O RUS-KIL Primer, LCF, Red 1.14 2 345 1 hr 4 hrs 4 hrs 55-DH-2 W/R ACRYLIC Metal Primer, LCF, Light Gray 1.39 2 341 30 min 1 hr 2 hrs 55-DR-9 W/R ACRYLIC Metal Primer, LCF, Red 1.61 1 602 30 min 1 hr 2 hrs 2.b WATERBORNE ALKYD METAL PRIMERS Manufactured to special order. Please contact your BLP Mobile Paints Sales Representative for particulars Ferrous Metals Systems - Primer Guide 4

2.c WATERBORNE EPOXY METAL PRIMERS Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle To Recoat 69-DR-1 MOPOXY H2O Epoxy Primer, LCF, Red 0.89 3 257 2 hrs 6 hrs 24 hrs Section 3 ZINC RICH PRIMERS 3.a INORGANIC ZINC RICH PRIMERS INORGANIC ZINC RICH PRIMERS offer excellent galvanic protection from corrosion in moderate to severe industrial and marine environments. Excellent resistance to fresh and salt water, detergents and most chemicals.very good resistance to most organic solvents. May require topcoating with epoxy or polyurethane for maximum chemical resistance. Heat resistant to 750 degrees Fahrenheit. Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle To Recoat 28-DH-50 MO-ZINC #3 Inorganic Zinc 3.88 3 342 1 hr 2 hrs 24 hrs 28-DH-86 MO-ZINC HS-15 Inorganic Zinc 3.40 3 380 1 hr 2 hrs 24 hrs 3.b ORGANIC ZINC RICH EPOXY PRIMERS ORGANIC ZINC RICH EPOXY PRIMERS offer excellent galvanic protection from corrosion in moderate to severe industrial and marine environments. Excellent resistance to fresh and salt water, detergents and most chemicals. Very good resistance to most organic solvents. Superior primer for use with high performance epoxy or polyurethane topcoats. Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle To Recoat 40-CM-2 MOPOXY ZR Epoxy Zinc Rich Primer 3.45 2.5 321 1 hr 4 hrs 18 hrs 40-CM-4 MOPOXY ZR Epoxy Zinc Rich Primer 3.89 3.5 257 30 min 1 hr 2 hrs 40-DH-6 MIL-DTL-24441 F 159 Zinc Rich Primer 2.50 3 336 2 hrs 8 hrs 12 hrs Ferrous Metals Systems - Primer Guide 5

Section 4 EPOXY PRIMERS FOR FERROUS METALS 4.a MoPoxY CATALYZED EPOXY PRIMERS MOPOXY Catalyzed Epoxy Primers offer excellent protection in moderate to severe industrial and marine environments. Excellent resistance to fresh and salt water, detergents and most chemicals. Very good resistance to fumes and spillage of most organic solvents, acids and alkalis. Specialized formulations available for specific services. Recommended primers under epoxy and polyurethane top coats. Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle To Recoat 613-10 MOPOXY HS High Solids Primer, LCF, Red 2.10 3 374 3 hrs 8 hrs 24 hrs 40-DR-5 MOPOXY HB High Build Metal Primer, Red 3.49 6 131 2 hrs 8 hrs 24 hrs 513-10 MOPOXY Epoxy Metal Primer, Red 4.24 2 322 2 hrs 8 hrs 24 hrs 40-DN-4 MOPOXY Primer, Yellow, MIL-P-23377 4.96 2 224 30 min 1 hr 2 hrs 40-DR-12 MOPOXY PCP Preconstruction Primer (LCF) 5.25 1 602 2 min 5 min 1 hr 4.b MOPOXY DTM PRIMERS & INTERMEDIATE COATS MOPOXY DTM Direct to Metal Primers offer excellent corrosion protection for steel surfaces where abrasive blasting is not feasible and for upgrading existing coating systems to high performance epoxy / polyurethane topcoats. Specialized formulations offer excellent recoatability, adhesion to damp surfaces, and other special advantages.41-af-2, MOPOXY Pre-Prep Sealer, is a 100% solids water-thin penetrating sealer formulated for areas where zero surface preparation is possible. Penetrates chalking and scaling paint, rust, and other contaminants to form a solid film which can be finished with a high performance epoxy-mastic polyurethane system. Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle To Recoat 41-AF-2 MOPOXY PRE-PREP Sealer, Clear 0.00 1 1604 48 hrs hard 24 hrs 40-AH-51 MOPOXY MASTIC, LCF, Gray 1.30 6 217 3 hrs 8 hrs 24 hrs 40-AR-19 MOPOXY MASTIC, LCF, Red 1.30 6 217 3 hrs 8 hrs 24 hrs 40-AW-32 MOPOXY MASTIC, LCF, White 1.30 6 217 3 hrs 8 hrs 24 hrs 40-AY-2 MOPOXY MASTIC, Aluminum 1.50 6 248 3 hrs 8 hrs 24 hrs 41-BK-14 MOPOXY IR Indefinate Recoat, LCF, Buff 2.29 8 136 1 hr 5 hrs 12 hrs 41-BH-3 MOPOXY ST HS LCF, Gray 2.36 8 131 16 hrs hard 5 hrs 41-BK-1 MOPOXY ST HS LCF, Buff 2.36 8 131 16 hrs hard 5 hrs 41-CH-1 MOPOXY PLUS, LCF, Gray 2.36 8 131 9 hrs hard 4 hrs 41-CW-1 MOPOXY PLUS, LCF, White 2.36 8 131 9 hrs hard 4 hrs Ferrous Metals Systems - Primer Guide 6

Section 5 COAL TAR EPOXIES 5.a MO-TAR COAL TAR EPOXY MO-TAR is a heavy-duty, chemical and corrosion resistant with excellent chemical and abrasion resistance in severe industrial & marine service. For steel and masonry surfaces. Excellent resistance to fresh and salt water, solvents, petroleum products, acids and alkalis. Excellent for underground and immersion service. All formulations are Lead-free and Chromate-Free. Product Item Description VOC DFT Sq Ft Dry Time: Code Mils Gallon ToTouch To Handle To Recoat 40-BX-6 MO-TAR HB-90 High Build Epoxy, Black 1.13 20 67 8 hrs 16 hrs 16 hrs 40-AR-16 MO-TAR C-200 Polyamide Epoxy, Red 1.56 8 157 4 hrs 6 hrs 6 hrs 40-AX-7 MO-TAR C-200 Polyamide Epoxy, Black 1.56 8 157 4 hrs 6 hrs 6 hrs Ferrous Metals Systems - Primer Guide 7

RECOMMENDED PAINTING SPECIFICATIONS FOR GALVANIZED METALS & ALUMINUM For Non-Immersion Service at Ambient Temperatures This section covers hot dip galvanized structural steel and steel plate, roof decking and piping, and aluminum surfaces, in interior and exterior service at ambient temperatures. Not intended for immersion service. Many paints are not compatible with zinc and require the application of vinyl wash primer as a pretreatment or of an acrylic primer to guarantee adhesion of coating systems to the zinc, as indicated in each system. Aluminum is included in this section because it also requires the use of vinyl wash primer or of an acrylic primer to promote adhesion. Inorganic zinc is not included in this section because it normally does not require application of vinyl wash primer for topcoat adhesion. See FERROUS METALS for application details. Vinyl wash primer contains zinc chromate. All other products are lead, chromate and mercury-free. SURFACE PREPARATION Galvanized steel sheet and pipe are customarily coated with oil to prevent galvanic action while stacked. This oil must be removed prior to painting. Solvent Cleaning, SSPC-SP 1, is the preferred method of removing oil and grease. Aluminum may be cleaned and etched with a Phosphoric acid based cleaner to promote coating adhesion. Surface preparation will be the same for all systems. Alternate Primers: Code Description VOC Sq. Ft. Mils 6-6 WEATHER-TITE 100% Acrylic Primer 1.17 393 2.00 9-5 GALVA-TEC Acrylic Primer 0.90 317 1.50 9-42 Vinyl Wash Primer 5.72 314 0.50 80439A&B MIL-P-21035 Cold Galvanize Repair 2.46 532 2.00 10-7 RUS-KIL Brite Galvanizing Coating 4.17 666 1.00 10-8 RUS-KIL Cold Galvanizing Coating 4.13 666 1.00 310-9 H2O RUS-KIL Acrylic DTM Primer 1.14 345 2.00 40-DN-4 MOPOXY Primer Yellow MIL-P-23377d 4.96 224 2.00 Galvanized Metals & Aluminum Systems 1

SECTION 01 ALKYD SYSTEMS FOR GALVANIZED & ALUMINUM 01 ALKYD SYSTEMS offer good protection against normal weathering, mild chemical fumes and normal abrasion. Least expensive, easiest surface preparation and application, shortest service life. Available in a wide range of colors. Not suitable for immersion service. Vinyl wash primer or acrylic metal primer required for adhesion. See above for Alternate Primers. All systems are VOC compliant. All are for interior and exterior service except as noted. Surface Preparation: Application: Solvent Clean, SSPC-SP1 to remove grease or oil. Brush, Roller, Airless or Conventional Spray. 01.A Alkyd System, High Gloss, Residential, Commercial & Industrial Service Coat Product High Gloss Enamel Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 10-Series RUS-KIL Gloss Enamel 3.35 385 2.00 Finish 10-Series RUS-KIL Gloss Enamel 3.35 385 2.00 Total Dry Mils 4.50 01.B Alkyd System, High Gloss, Residential, Commercial, & Industrial Service Coat Product Alkyd Semi-Gloss Enamel Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 30-Series NAM-A-LAC Non-Toxic Enamel 3.18 314 1.50 Finish 30-Series NAM-A-LAC Non-Toxic Enamel 3.18 314 1.50 Total Dry Mils 3.50 01.C Alkyd System, Semigloss, Residential, Commercial, & Light Industrial Service Coat Product High Gloss Enamel Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 135-Series COVENTRY Lustarite Satin-Gloss 3.04 427 2.00 Finish 135-Series COVENTRY Lustarite Satin-Gloss 3.04 427 2.00 Total Dry Mils 4.50 Galvanized Metals & Aluminum Systems 2

01.D Alkyd System, Spray Fog-Dry, Flat, Interior, Commercial & Industrial Service Coat Product Sweep-Dry Flat Enamel Finish VOC Sq Ft Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 6-DW-58* SPRAY FOG-DRY Flat White 3.17 407 2.00 Finish 6-DW-58* SPRAY FOG-DRY Flat White 3.17 407 2.00 * Apply by airless spray Total Dry Mils 4.50 01.E Alkyd System, Spray Fog Dry, Semi-Gloss, Interior, Commercial & Industrial Service Coat Product Sweep-Dry Semi-Gloss Enamel Finish VOC Sq Ft Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 61-BW-2* SPRAY FOG-DRY Semi-Gloss White 3.25 382 2.00 Finish 61-BW-2* SPRAY FOG-DRY Semi-Gloss White 3.25 382 2.00 * Apply by airless spray Total Dry Mils 4.50 SECTION 02 ACRYLIC LATEX SYSTEMS FOR GALVANIZED & ALUMINUM 02 WATERBORNE ACRYLIC LATEX ENAMELS are the latest development in general-purpose finishes for interior and exterior service. Easy to apply over a variety of primers and substrates including zinc and galvanized metals. Good resistance to normal weathering and mild chemical fumes. Not for immersion service. Lead, chromate and mercury free. Low VOC. Apply directly to zinc or aluminum. No pretreatment required. Acrylic latex primer optional. Surface Preparation: Application: Solvent Clean, SSPC-SP 1, to remove oil or grease. Brush, Roller, Airless or Conventional Spray 02.A Acrylic Latex System, High-Gloss, Residential to Light Industrial Service Coat Product High Gloss Acrylic Finish VOC Sq. Ft. Mils Prime* 310-9 H2O RUS-KIL Acrylic Metal Primer 1.14 345 2.00 Intermediate 310-Series H2O RUS-KIL Acrylic DTM Finish 1.09 295 2.00 Finish 310-Series H2O RUS-KIL Acrylic DTM Finish 1.09 295 2.00 *Corrosion-resistant primer optional Total Dry Mils 6.00 Galvanized Metals & Aluminum Systems 3

02.B Acrylic Latex DTM System, High-Gloss, Residential to Light Industrial Service Coat Product High Gloss DTM Acrylic Finish VOC Sq. Ft. Mils Prime* 310-9 H2O RUS-KIL Acrylic DTM Metal Primer 1.14 345 2.00 Intermediate 330-Series ACR-A-LAC 100% Acrylic Gloss 2.11 293 2.00 Finish 330-Series ACR-A-LAC 100% Acrylic Gloss 2.11 293 2.00 *Corrosion-resistant primer optional Total Dry Mils 6.00 02.C Acrylic Latex System, Exterior, Gloss, Residential to Light Industrial Service Coat Product Gloss Acrylic Finish VOC Sq. Ft. Mils Prime 6-6 WEATHER-TITE Universal Primer 1.17 393 1.50 Intermediate 140-Series WEATHER-TITE 100% Acrylic Gloss 1.99 296 2.00 Finish 140-Series WEATHER-TITE 100% Acrylic Gloss 1.99 296 2.00 Total Dry Mils 5.50 02.D Acrylic Latex System, Exterior, Satin Gloss, Residential to Light Industrial Service Coat Product Satin-Gloss Acrylic Finish VOC Sq. Ft. Mils Prime 6-6 WEATHER-TITE Universal Primer 1.17 393 1.50 Intermediate 240-Series WEATHER-TITE 100% Acrylic Satin 2.19 271 2.00 Finish 240-Series WEATHER-TITE 100% Acrylic Satin 2.19 271 2.00 Total Dry Mils 5.50 02.E Acrylic Latex System, Exterior, Flat, Residential to Light Industrial Service Coat Product Flat Acrylic Finish VOC Sq. Ft. Mils Prime 6-6 WEATHER-TITE Universal Primer 1.17 393 1.50 Intermediate 40-Series WEATHER-TITE 100% Acrylic Flat 1.03 291 2.00 Finish 40-Series WEATHER-TITE 100% Acrylic Flat 1.03 291 2.00 Total Dry Mils 5.50 Galvanized Metals & Aluminum Systems 4

02.F Vinyl Latex System, Interior, Flat, Residential to Light Industrial Service Coat Product Flat Latex Finish VOC Sq. Ft. Mils Prime* 310-9 H2O RUS-KIL Acrylic DTM Metal Primer 1.14 345 2.00 Intermediate 35-Series COVENTRY Interior Latex Flat 0.83 375 1.50 Finish 35-Series COVENTRY Interior Latex Flat 0.83 375 1.50 *Corrosion-resistant primer optional Total Dry Mils 5.00 02.G Acrylic Latex System, Interior, Semi-Gloss, Residential to Light Industrial Service Coat Product Semi-Gloss Acrylic Finish VOC Sq. Ft. Mils Prime* 310-9 H2O RUS-KIL Acrylic DTM Metal Primer 1.14 345 2.00 Intermediate 1335-Series COVENTRY Latex Semi-Gloss 2.00 345 1.50 Finish 1335-Series COVENTRY Latex Semi-Gloss 2.00 345 1.50 *Corrosion-resistant primer optional Total Dry Mils 5.00 02.H Acrylic Latex System, Interior, Eggshell, Residential to Light Industrial Service Coat Product Eggshell Acrylic Finish VOC Sq. Ft. Mils Prime* 310-9 H2O RUS-KIL Acrylic DTM Metal Primer 1.14 345 2.00 Intermediate 2335-Series COVENTRY Acrylic Eggshell 0.86 375 1.50 Finish 2335-Series COVENTRY Acrylic Eggshell 0.86 375 1.50 *Corrosion-resistant primer optional Total Dry Mils 5.00 02.I Acrylic Latex System, Interior, High Gloss, Residential to Light Industrial Service Coat Product High Gloss Acrylic Enamel Finish VOC Sq. Ft. Mils Prime* 310-9 H2O RUS-KIL Acrylic DTM Metal Primer 1.14 345 2.00 Intermediate 335-Series COVENTRY Acrylic High Gloss Enamel 1.09 408 1.50 Finish 335-Series COVENTRY Acrylic High Gloss Enamel 1.09 408 1.50 *Corrosion-resistant primer optional Total Dry Mils 5.00 Galvanized Metals & Aluminum Systems 5

02.J Acrylic Latex System, Interior, Fog-Dry Flat, Commercial & Industrial Service Coat Product Flat Sweep-Dry Acrylic Finish VOC Sq. Ft. Mils Prime 310-9 H2O RUS-KIL Acrylic DTM Metal Primer 1.14 345 2.00 Intermediate 55-DW-3* SPRAY Fog-Dry Acrylic Flat White 0.80 322 2.00 Finish 55-DW-3* SPRAY Fog-Dry Acrylic Flat White 0.80 322 2.00 *Use airless spray Total Dry Mils 6.00 02.K Acrylic Latex System, Interior, Fog-Dry Gloss, Commercial & Industrial Service Coat Product Gloss Sweep-Dry Acrylic Finish VOC Sq. Ft. Mils Prime 310-9 H2O RUS-KIL Acrylic DTM Metal Primer 1.14 345 2.00 Intermediate 55-AW-9* SPRAY Fog-Dry Acrylic Gloss White 0.75 289 2.00 Finish 55-AW-9* SPRAY Fog-Dry Acrylic Gloss White 0.75 289 2.00 *Use airless spray Total Dry Mils 6.00 SECTION 03 SILICONE ALKYD SYSTEMS FOR GALVANIZED & ALUMINUM 03 SILICONE ALKYDS offer outstanding gloss and color retention, excellent resistance to industrial and marine environments, weathering and ultraviolet exposure, and good resistance to mild chemical fumes. Not for immersion service. Easy to apply. Lead, chromate and mercury free. VOC compliant. Vinyl wash primer or acrylic latex metal primer required for adhesion. All systems are VOC Compliant Surface Preparation: Application: Solvent Clean, SSPC-SP1 to remove grease or oil. Brush, Roller, Airless or Conventional Spray. 03.A Silicone Alkyd System, High Gloss, Residential, Commercial, Marine & Industrial Service Coat Product High Gloss Silicone Alkyd Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 314 0.50 Intermediate 432-Series JACK TAR Silicone Yacht Finish 484 1.50 Finish 432-Series JACK TAR Silicone Yacht Finish 484 1.50 Total Dry Mils 3.50 Galvanized Metals & Aluminum Systems 6

SECTION 04 EPOXY & POLYURETHANE SYSTEMS FOR GALVANIZED & ALUMINUM 04 CATALYZED EPOXY AND POLYURETHANE SYSTEMS offer superior resistance to many chemicals, especially alkalis, abrasion, and moisture, together with good resistance to most organic solvents, acid splashes and chemical fumes. For Commercial, Heavy Industrial and Marine Service at ambient temperatures. We do not recommend galvanized metal for immersion service because of possible galvanic action. CATALYZED EPOXIES are excellent for interior use in schools, hospitals, institutions, laundries, kitchens and food processing areas, chemical and pharmaceutical plants, and other industrial and commercial installations where maximum protection and durability are required. Available in high gloss and semigloss in a wide range of colors for an easily clean and attractive finish. Waterborne formulations are available. The following primers are recommended for adhesion: Code Description VOC Sq. Ft. Mils 9-42 Vinyl Wash Primer 5.72 314 0.50 40-DN-4 MOPOXY Primer Yellow MIL-P-23377 4.96 224 2.00 310-9 H2O RUS-KIL Acrylic DTM Primer 1.14 345 2.00 CATALYZED POLYURETHANES offer good chemical and solvent resistance with outstanding color and gloss retention. Recommended for marine environments, tank farms, pipe racks, chemical plants, and heavy equipment. Not for immersion service. The following catalyzed polyurethane formulations are available and may be used interchangeably within the suggested system recommendations. Other formulations are available for special service. Code Description VOC Sq Ft DFT /Gal 72-Series MOTHANE Polyurethane Enamel 4.11 339 2 Apply by Airless or Conventional Spray only 72-Series MOTHANE HD (Heavy Duty) Polyurethane 4.11 268 2.5 Apply by Airless or Conventional Spray, Brush or Roll 72-Series MOTHANE HS-1000 (High Solids) Polyurethane 2.45 513 2 Apply by Airless or Conventional Spray, Brush or Roll 72-Series MOTHANE HS-900 (High Solids) Polyurethane 2.47 417 2.5 Apply by Airless or Conventional Spray only Mobile Paints offers a wide range of epoxies and polyurethanes for special applications. Ask your BLP Mobile Paint representative for detailed recommendations. Surface Preparation: Application: Solvent Clean, SSPC-SP1, to remove oil and grease Brush, Roller, Airless or Conventional Spray unless otherwise indicated. Galvanized Metals & Aluminum Systems 7

04.A Catalyzed Waterborne Acrylic Epoxy System, Commercial & Industrial Service Coat Product High Gloss W/B Catalyzed Acrylic VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 69-AW-5 MOPOXY H2O-100 W/B Acrylic Epoxy 1.71 313 2.00 Finish 69-AW-5 MOPOXY H2O-100 W/B Acrylic Epoxy 1.71 313 2.00 Total Dry Mils 4.50 04.B Catalyzed Waterborne Amide Epoxy System, Commercial & Industrial Service Coat Product Semi-Gloss W/B Amide Epoxy Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 69-AW-6 MOPOXY H2O-200 W/B Amide Epoxy 1.00 225 2.00 Finish 69-AW-6 MOPOXY H2O-200 W/B Amide Epoxy 1.00 225 2.00 Total Dry Mils 4.50 04.C Catalyzed Epoxy System, Commercial & Industrial Service Coat Product High Gloss Epoxy Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 513-Series MOPOXY High Gloss Epoxy 4.30 314 2.00 Finish 513-Series MOPOXY High Gloss Epoxy 4.30 314 2.00 Total Dry Mils 4.50 04.D Catalyzed Epoxy System, Commercial & Industrial Service Coat Product High Solids Semi-Gloss Epoxy Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 613-Series MOPOXY HS High Solids S/G Epoxy 2.00 374 3.00 Finish 613-Series MOPOXY HS High Solids S/G Epoxy 2.00 374 3.00 Total Dry Mils 6.50 Galvanized Metals & Aluminum Systems 8

04.E Catalyzed Epoxy Mastic /Epoxy System, Heavy Industrial & Marine Service Coat Product High Solids Semi-Gloss Epoxy Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 40-AW-32 MOPOXY MASTIC White 1.30 217 6.00 Finish 613-Series MOPOXY HS High Solids Epoxy 2.00 374 3.00 Finish 613-Series MOPOXY HS High Solids Epoxy 2.00 374 3.00 Total Dry Mils 12.50 04.F Catalyzed Epoxy Mastic /Acrylic Epoxy System, Heavy Industrial & Marine Service Coat Product High Gloss Acrylic Epoxy Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6.00 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2.00 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2.00 Total Dry Mils 10.50 04.G Catalyzed Epoxy Mastic /Polyurethane System, Heavy Industrial & Marine Service Coat Product High Solids Gloss Polyurethane Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 40-AW-32 MOPOXY Mastic, White 1.30 217 6.00 Finish 72-Series MOTHANE HD Polyurethane 4.11 268 2.50 Finish 72-Series MOTHANE HD Polyurethane 4.11 268 2.50 Total Dry Mils 11.50 04.H Catalyzed DTM Epoxy /Polyurethane System, Heavy Industrial & Marine Service Coat Product High Gloss Polyurethane Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 41-CW-1 MOPOXY-PLUS DTM Epoxy 2.36 131 6.00 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane 2.45 268 2.00 Finish 72-AW-6 MOTHANE HS-1000 Polyurethane 2.45 268 2.00 Total Dry Mils 10.50 Galvanized Metals & Aluminum Systems 9

04.I Catalyzed DTM Epoxy /Acrylic Epoxy System, Heavy Industrial & Marine Service Coat Product High Gloss Acrylic Epoxy Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 41-CW-1 MOPOXY-PLUS DTM Epoxy 2.36 131 6.00 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2.00 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2.00 Total Dry Mils 10.50 04.J Recoatable Epoxy / Polyurethane System, Heavy Industrial & Marine Service Coat Product High Gloss Polyurethane Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8.00 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2.00 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2.00 Total Dry Mils 12.50 04.K Recoatable Epoxy / Acrylic Epoxy System, Heavy Industrial & Marine Service Coat Product High Gloss Acrylic Epoxy Finish VOC Sq. Ft. Mils Pretreat 9-42 Vinyl Wash Primer 5.72 314 0.50 Intermediate 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8.00 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2.00 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2.00 Total Dry Mils 12.50 Galvanized Metals & Aluminum Systems 10

SECTION 05 - MAINTENANCE UPGRADE SYSTEMS: 05 FOR UPGRADING deteriorated alkyd, silicone alkyd and acrylic finishes and repairing catalyzed epoxy and polyurethane systems where removal of existing coatings is not possible. MOPOXY MASTIC Aluminum is a very high solids, low VOC, surface tolerant high performance epoxy coating offering excellent protection in moderate to severe industrial and marine environments. DTM or use as base coating over sound rust and /or previous paint for upgrading to high performance topcoats. MOPOXY MASTIC is a high-solids, high-build, surface tolerant amine epoxy formulated for application over sound rust and/or previous paint systems as a base coat for upgrading to high performance coatings such as acrylic epoxies and polyurethanes. MOPOXY IR, Indefinite Recoatability Epoxy, is a high-solids, surface-tolerant, high-build polyamide coating which may be applied to damp, rusty surfaces, allowed to dry for prolonged periods, then topcoated with other epoxies or polyurethanes without loss of intercoat adhesion. Good anticorrosive properties. MOPOXY PLUS is a high-performance high-solids DTM polyamide epoxy with excellent adhesion to tight rust, good adhesion to damp surfaces, and cures at low temperatures. Excellent resistance to fresh and salt water, detergents and corrosive chemicals. Very good resistance to fumes and spills of most organic solvents, acids and alkalis. MOPOXY PRE-PREP is a 100% solids epoxy with very low viscosity and excellent substrate wetting properties. Excellent for badly rusted areas where sandblasting and removal of existing coatings is not possible and only minimal cleaning is possible. Penetrates and bonds rust and deteriorated coatings into a solid film which seals out moisture and oxygen. Allow to cure for 24 hours, then apply recommended intermediate coat while still slightly soft. Will accept a wide variety of coatings. MO-BAR Universal Primer is a high-quality, quick-drying modified alkyd anticorrosive primer or shop coat. Use as a barrier coat to prevent lifting of solvent-sensitive coatings by high performance top coats. Excellent protection against corrosion in mild industrial and marine environments. All systems recommended are suitable for heavy industrial and marine service. Surface Preparation: Application: Pressure Wash (3,000 psi or better) to remove contamination Solvent Clean, SSPC-SP 1, to remove oil and grease Power Tool Clean, SSPC-SP 2, preferred Hand Tool Clean, SSPC-SP 3, minimum recommended Brush, roller or airless or conventional spray. Galvanized Metals & Aluminum Systems 11

05.A Epoxy Mastic / High Solids Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq. Ft. Mils Spot Prime 40-AY-2 MOPOXY MASTIC, Aluminum 0.51 248 6 Prime 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 72-Series MOTHANE HD Polyurethane 4.11 2.68 2.5 Finish 72-Series MOTHANE HD Polyurethane 4.11 2.68 2.5 Total Dry Mils 17.0 05.B Epoxy Mastic / Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq. Ft. Mils Spot Prime 40-AY-2 MOPOXY MASTIC, Aluminum 0.51 248 6 Prime 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 16.0 05.C IR Epoxy / High Solids Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq. Ft. Mils Spot Prime 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Prime 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 20.0 05.D IR Epoxy / Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq. Ft. Mils Spot Prime 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Prime 41-BK-14 MOPOXY IR High Solids Epoxy Buff 2.29 136 8 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 20.0 Galvanized Metals & Aluminum Systems 12

05-E Low Viscosity Epoxy / Epoxy Mastic / High Solids Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq. Ft. Mils Prime 41-AF-2 MOPOXY PrePrep Clear 0.00 1069 1.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 11.5 05-F Low Viscosity Epoxy / Epoxy Mastic / Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq. Ft. Mils Prime 41-AF-2 MOPOXY PrePrep Clear 0.00 1069 1.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 11.5 05-G Universal Primer / Epoxy Mastic / High Solids Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq. Ft. Mils Prime 28-DR-160 MO-BAR PM-III Universal Primer 3.49 393 1.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 11.5 05-H Universal Primer / Epoxy Mastic / Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq. Ft. Mils Prime 28-DR-160 MO-BAR PM-III Universal Primer 3.49 393 1.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 11.5 Galvanized Metals & Aluminum Systems 13

RECOMMENDED PAINTING SPECIFICATIONS FOR FERROUS METALS AT HIGH TEMPERATURES For Non-Immersion Service Only PART I INTRODUCTION Surface Preparation and Temperature Ranges for Paints Part II INDEX OF COATING SYSTEMS Detailed Index of Coating Systems Part III COATING SYSTEMS Recommended Primers, Intermediate Coats Finish Coats, Dry Film Thickness and Coverage SUMMARY INDEX 01 - Steel Surfaces - up to 200 O F, Constant 02 - Steel Surfaces - up to 300 O F, Constant 03 - Steel Surfaces - up to 500 O F, Constant 04 - Steel Surfaces - up to 500 O F Constant, 800 O F Intermittent 05 - Steel Surfaces - up to 800 O F Constant, 1000 O F Intermittent INDEX OF PRODUCT DATA SHEETS High Temperature Paint Systems for Ferrous Metals 1

RECOMMENDED PAINTING SPECIFICATIONS FOR FERROUS METALS AT HIGH TEMPERATURES PART I INTRODUCTION This section covers ferrous metals, including structural steel, chimneys, exteriors of storage tanks and silos, tubing and pipes, boilers, compressors, reactors, generators, heat exchangers and similar equipment for non-immersion service at elevated temperatures. Proper surface preparation is essential to the life of any coating system. Sandblasting is the preferred method of removing rust and mill scale on new steel and old paint, rust, and similar contaminants on previously painted steel prior to coating. In addition to cleaning the surface, sandblasting cuts the steel to provide an anchor pattern which assures good adhesion of the primer to the substrate. Solvent clean to remove grease, oil and similar contaminants which cannot be removed successfully with abrasive blast cleaning. The Society for Protective Coatings, formerly the Steel Structures Painting Council is the recognized authority on surface preparation and painting procedures for steel and reference is made to their standards as follows: Solvent Cleaning SSPC-SP 1 Hand Cleaning SSPC-SP 2 Power Tool Cleaning SSPC-SP 3 White Metal Blast SSPC-SP 5 Commercial Blast SSPC-SP 6 Brush-off Blast SSPC-SP 7 Near White Blast SSPC-SP 10 Power Tool Cleaning to Bare Metal SSPC-SP 11 See Section 3, SSPC, for detailed descriptions of the above standards. Commercial Blast cleaning should be considered the minimum acceptable surface preparation when specifying paint systems for service at elevated temperatures. Wet sandblasting is becoming more common because of stringent EPA requirements, requiring new techniques and the use of additives to the blasting water to prevent immediate rust bloom. Consult your BLP Mobile Paint representative for equipment and additive recommendations. High Temperature Paint Systems for Ferrous Metals 2

RECOMMENDED PAINTING SPECIFICATIONS FOR FERROUS METALS AT HIGH TEMPERATURES PART I INTRODUCTION (continued) MAXIMUM OPERATING TEMPERATURES FOR PAINTS Zinc melts at 780 degrees Fahrenheit. Aluminum melts at 1,220 degrees. Steel turns red at 1,000 degrees and melts at 1,535 degrees. Paints oxidize at accelerated rates as the temperature increases. Because of the importance of determining the exact temperature range required, it is recommended that surface temperatures be verified with an accurate thermometer. Please call your nearest BLP Mobile Paint representative for assistance. The following guide is conservative and for non-immersion service only. Temperatures are shown in degrees Fahrenheit. Product Product Description Code Constant Intermittent Vinyl, Solvent Thinned 160 180 Chlorinated Rubber 160 180 Phenolic, Non-Catalyzed 190 180 Alkyd Enamels 275 300 Acrylic Latex Gloss Enamels 200 250 Epoxies, Catalyzed 200 250 Epoxy-Phenolic, Catalyzed 200 250 Polyurethane, Catalyzed 200 250 Silicone Alkyd Primer 28-DR-79 375 400 Silicone Alkyd Enamel 432-Line 300 400 Silicone Alkyd Aluminum 11-61 500 600 Inorganic Zinc 28-DH-50 600 750 HR Silicone Acrylic Aluminum 62-AY-5 800 1,000 Silicone Hi-Heat Aluminum 62-AY-1 1,000 1,200 High Temperature Paint Systems for Ferrous Metals 3

RECOMMENDED PAINTING SPECIFICATIONS FOR FERROUS METALS AT HIGH TEMPERATURES Part II INDEX OF COATING SYSTEMS 01 - Steel Surfaces - up to 200 O F, Constant 01.A Inorganic Zinc/Epoxy/Polyurethane System for Heavy Industrial Service 01.B Zinc Rich Epoxy/Epoxy/Polyurethane System for Heavy Industrial Service 01.C Inorganic Zinc/Modified Acrylic Latex System for Light Industrial Service 01.D Alkyd/Silicone Alkyd System for Residential, Marine and Light Industrial Service 01.E Acrylic Latex DTM System for Residential to Light Industrial Service 02 - Steel Surfaces - up to 300 O F, Constant 02.A Silicone Alkyd System for Heavy Industrial Service 03 - Steel Surfaces - up to 500 O F, Constant 03.A Silicone Alkyd Aluminum for Heavy Industrial Service 04 - Steel Surfaces - up to 500 O F Constant, 800 O F Intermittent 04.A Heat Resitant - Silcone Acrylic Aluminum for Heavy Industrial Service 05 - Steel Surfaces - up to 800 O F Constant, 1000 O F Intermittent 05.A Silicone Acrylic Aluminum for Heavy Industrial Service High Temperature Paint Systems for Ferrous Metals 4

01 STEEL SURFACES, AMBIENT TEMPERATURE UP TO 200 F CONSTANT 01.A Inorganic Zinc/Epoxy/Polyurethane System for maximum protection Coat Product VOC Sq Ft Mils Shop Prime 28-DH-50 MO-ZINC #3 Inorganic Zinc 3.88 342 3 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.3 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 13.0 01.B Zinc Rich Epoxy/Epoxy/Polyurethane System for maximum protection Coat Product VOC Sq Ft Mils Prime 40-CM-2 MOPOXY ZR Zinc Rich Primer 3.45 321 2.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.3 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 12.5 01.C Inorganic Zinc/Modified Acrylic Latex DTM System for superior protection Coat Product VOC Sq Ft Mils Shop Prime 28-DH-50 MO-ZINC #3 Inorganic Zinc 3.88 342 3 Finish 310-Series H 2 O RUS-KIL DTM Acrylic Enamel 1.09 295 2 Finish 310-Series H 2 O RUS-KIL DTM Acrylic Enamel 1.09 295 2 Total Dry Mils 7.0 High Temperature Paint Systems for Ferrous Metals 5

01.D Alkyd/Silicone Alkyd System for superior gloss and color retention Coat Product High Gloss VOC Sq Ft Mils Shop 28-DR-160 MO-BAR PM-III Universal Primer 3.49 387 2 Prime 28-DR-160 MO-BAR PM-III Universal Primer 3.49 387 2 Intermediate 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.5 Finish 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.5 Total Dry Mils 7.0 01.E Acrylic Latex DTM System, High Gloss, for light industrial service Coat Product VOC Sq Ft Mils Shop 310-9 H 2 O RUS-KIL Acrylic Metal Primer 1.14 345 2 Prime 310-9 H 2 O RUS-KIL Acrylic Metal Primer 1.14 345 2 Intermediate 310-Series H 2 O RUS-KIL Acrylic DTM Enamel 1.09 295 2 Finish 310-Series H 2 O RUS-KIL Acrylic DTM Enamel 1.09 295 2 Total Dry Mils 8.0 02 STEEL SURFACES UP TO 300 o F CONSTANT 02.A Silicone Alkyd System for good corrosion resistance, excellent gloss retention Coat Product VOC Sq Ft Mils Shop 28-DR-79 Silicone Alkyd Primer 3.76 449 1.5 Prime 28-DR-79 Silicone Alkyd Primer 3.76 449 1.5 Intermediate 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.5 Finish 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.5 Total Dry Mils 6.0 High Temperature Paint Systems for Ferrous Metals 6

03 STEEL SURFACES UP TO 500 o F CONSTANT 03.A Silicone Alkyd Aluminum for good corrosion resistance, excellent gloss retention Coat Product VOC Sq Ft Mils Prime 11-61 HR Silicone Alkyd Aluminum 4.61 450 1 Finish 11-61 HR Silicone Alkyd Aluminum 4.61 450 1 Total Dry Mils 2.0 04 STEEL SURFACES UP TO 500 o F CONSTANT, 800 o F INTERMITTENT 04.A Silicone Acrylic Aluminum for good corrosion resistance, gloss retention Coat Product VOC Sq Ft Mils Prime 62-AY-5 HR Silicone Acrylic Aluminum 4.34 427 1.5 Finish 62-AY-5 HR Silicone Acrylic Aluminum 4.34 427 1.5 Total Dry Mils 3.0 05 STEEL SURFACES UP TO 800 o F CONSTANT, 1,000 o F INTERMITTENT 05.A Silicone Aluminum for good corrosion resistance, excellent gloss retention Coat Product VOC Sq Ft Mils Prime 62-AY-1 HR Silicone Aluminum 4.38 409 1.5 Finish 62-AY-1 HR Silicone Aluminum 4.38 409 1.5 Total Dry Mils 3.0 High Temperature Paint Systems for Ferrous Metals 7

RECOMMENDED PAINTING SPECIFICATIONS FOR EXTERIOR MASONRY SURFACES INDEX Index of Recommended Coating Systems for Exterior Masonry Page 1 Each system includes prime or fill coat, first and second coats of compatible products. First, look for the substrate to be coated, then the type of finish desired Introduction - Recommended Painting Specifications Page 2 A basic introduction to our products Recommended Products Page 2 All products listed are recognized for their history of quality and service. Product data sheets and color cards are in the last section of this book Application Details for Painting Exterior Masonry Page 5 SUGGESTED SYSTEMS Section 01 Exterior Exposed Block or Concrete Masonry Units Page 7 Section 02 Exterior Cement Plaster, Stucco, Concrete, Brick or Drywall Page 10 Section 03 Exterior Exposed Plaster, Concrete or Brick Clear Sealant Page 14 Section 04 Concrete Secondary Contention Dike Systems Page 15 Section 05 Traffic Zone Marking on Concrete and Asphalt Page 16 Exterior Masonry Systems 1

RECOMMENDED PAINTING SPECIFICATIONS FOR EXTERIOR MASONRY SURFACES Mobile Paints was founded in Mobile, Alabama in 1921 and was a pioneer in formulating top-quality architectural, industrial and marine coatings and finishes for tropical and subtropical climates. From this beginning, Mobile has expanded throughout the Southeastern and South Central United States, Puerto Rico and the Virgin Islands. Mobile Paints is recognized for its dedication to quality and service. This section includes recommendations for finishing new exterior concrete, cement block, brick, plaster or stucco surfaces exposed to normal conditions experienced in typical residential, commercial, industrial and marine environments, for protecting masonry surfaces which are to be left unpainted, and for refinishing previously painted masonry surfaces. For severe exposures and specific coating problems, please consult your BLP Mobile Paint representative. RECOMMENDED COATINGS AND PRIMERS WEATHER-TITE TM is the modern industry standard for exterior masonry coatings. Formulated with 100% acrylic resins, it breathes, allowing moisture in the wall to transpire and evaporate without damaging the paint film. WEATHER-TITE TM has exceptional color stability and is available in a wide range of designer colors. It has outstanding resistance to blistering, lime burn and ultraviolet degradation. WEATHER-TITE TM contains an effective mildewcide, is lead-free, chromate-free, mercury- free, and low VOC. WEATHER-TITE TM 100% Acrylic Latex House Paint is formulated in Flat, Gloss and Satin finishes. WEATHER-TITE TM 100% Acrylic Universal Primer and WEATHER-TITE TM Premium 100 Caulk are part of the complete line of WEATHER-TITE TM exterior paints and coatings. WEATHER-TITE TM ELASTOMERIC Wall Coating has extraordinary properties of elongation, stretching and contracting with the substrate while bridging small cracks and waterproofing against wind-driven rain. Especially recommended for older buildings with moisture problems. SMOOTH-COTE and Architectural are the brand names for our contractor professional coatings which are available in a complete line of interior and exterior finishes and primers. All exterior products contain an effective mildewcide. All are leadfree, mercury-free, chromate-free, and low VOC. Exterior Masonry Systems 2

RECOMMENDED PAINTING SPECIFICATIONS FOR EXTERIOR MASONRY SURFACES RECOMMENDED COATINGS AND PRIMERS (continued) In addition to the above architectural latex acrylic coatings for residential, commercial, and light industrial service, the following products are recommended for areas subject to more severe service, such as schools, service stations, laundries, car washes, and hospitals, up to and including heavy industrial installations. All are available in an excellent selection of standard colors as shown on their respective color cards and in a wide range of custom colors NAM-A-LAC is the brand name for our first line high gloss alkyd enamels. Nontoxic, self-leveling, fast drying, they are available in a wide range of stock colors as well as an extensive palette of custom colors. Recommended for interior and exterior service over properly prepared wood, metal or masonry surfaces. Very good color retention, good abrasion and solvent resistance, good resistance to marine and mild industrial environments. ACR-A-LAC TM is the brand name for our line of waterborne high gloss acrylic enamels, which share the same color card with our NAM-A-LAC line. 100% acrylic, they have superior gloss and color retention and are excellent for residential, institutional, commercial and light industrial service. Low odor, low VOC, fast drying, they are suitable for interior and exterior service over properly prepared wood, metal or masonry surfaces. RUS-KIL is the brand name for our line of rust inhibiting alkyd enamels for residential, institutional, commercial and industrial service. Available in OSHA Safety Colors and a wide range of industrial and custom colors. Suitable for interior and exterior service over properly prepared wood, metal or masonry surfaces. H 2 O RUS-KIL is the brand name for our line of direct-to-metal (DTM) waterborne high gloss acrylic enamels which share the RUS-KIL color card. 100% acrylic, they have excellent gloss and color retention. Low odor, low VOC, and fast drying H 2 O RUS-KIL gives excellent interior and exterior service over properly prepared wood, metal or masonry surfaces. MoPoxY TM is Mobile Paints brand name for our family of catalyzed epoxies which offer superior resistance to fresh and salt water, solvents, many chemicals and abrasion for institutional, commercial, industrial and marine service where maximum protection and durability are required. Special formulations are stocked for use in food processing plants, kitchens, pharmaceutical plants and other areas requiring direct food contact or FDA certification. MoPoxY TM is recommended for use in schools, hospitals, laundries, shopping centers, chemical and pharmaceutical plants, waste water treatment plants, potable water storage tanks, and other industrial and commercial installations. Please consult your BLP Mobile Paint Representative for specific recommendations for problem areas. Exterior Masonry Systems 3

RECOMMENDED PAINTING SPECIFICATIONS FOR EXTERIOR MASONRY SURFACES RECOMMENDED COATINGS AND PRIMERS (continued) MoPoxY TM is available in solvent-thinned, waterborne and 100% solids formulations. While most epoxies will chalk under ultraviolet exposure, ultraviolet-resistant formulations are available. MoPoxY TM is available in standard industrial colors, OSHA safety colors, and many custom colors on special order. MOTHANE TM is Mobile Paint s brand name for our family of catalyzed polyurethanes which combine good chemical and abrasion resistance with outstanding color and gloss retention and ease of application. Usually specified as top coat in epoxy-polyurethane systems for heavy industrial and marine service, MOTHANE has been proven effective as a masonry finish in areas such as in service stations where an easily maintained exterior finish is required. Available in several formulations and a wide range of stock and custom colors. H 2 O LOX CHALK Clear sealer is a highly penetrating, clear waterborne acrylic sealer which penetrates and bonds residual chalk left on exterior masonry surfaces after cleaning. Seals the surface and provides excellent adhesion for finish coats. Low odor, excellent resistance to moisture and alkali. Lead-free, mercury-free, chromate-free and low VOC. Please consult your BLP Mobile Paint Representative for specific recommendations. Exterior Masonry Systems 4

APPLICATION DETAILS FOR PAINTING EXTERIOR MASONRY SURFACES Proper surface preparation is essential for the maximum life of any painting or coating system. New masonry should be allowed to cure for at least 30 days before painting. Surfaces should be clean, dry, and free of dust, laitance, and form-release oil. All window frames, door jambs, joints and hairline cracks should be caulked with WEATHER-TITE TM Premium 100 Siliconized Acrylic Caulking. Larger cracks should be filled and bridged with WEATHER-TITE TM Elastomeric Patch. Fill exposed block or Concrete Masonry Units (CMU) with one coat of BLOC-FIL TM Latex Block Filler, 60-7, before finishing. Prime new masonry with WEATHER-TITE TM 100% Acrylic Universal Primer, 6-6, to seal the surface and provide better adhesion and coverage to the finish coats. Proper priming will add considerably to the life of the painting system and will also make maintenance repainting easier in the future. Old or previously painted masonry surfaces should be pressure washed to remove dirt and chalking or peeling paint. Kill mildew with a solution of JOMAX and Clorox as directed on the JOMAX label. Apply with a low pressure sprayer, allow to penetrate and kill the roots of the mildew, then wash with high pressure water. Remove grease or oil with detergents. Rinse. Surface must be clean and dry and chalk free prior to painting. Prime either with WEATHER-TITE TM Universal Primer 6-6, H 2 0 LOX CHALK Clear Acrylic Sealer 74-45 or Smooth-Cote Exterior Primer 206-10. Caulk all window frames, door jams, joints and cracks with WEATHER-TITE TM Premium 100 Caulk. Larger cracks should be filled and bridged with WEATHER-TITE TM Elastomeric Patch. When applying WEATHER-TITE TM Elastomeric Wall Coating, special attention should be given to surface preparation in order to assure proper adhesion to the substrate and complete sealing of all cracks, joints, window frames, door jams, and other areas where water can penetrate the fabric of the building. It is also important to apply the full recommended dry film thickness for maximum protection. The recommended form of application is by airless spray in order to achieve 7.5 mils dry per coat. If applied by roller, this will normally require two coats because of the weight or viscosity of the product. Please consult your BLP Mobile Paint Representative for specific recommendations for problem areas. Exterior Masonry Systems 5

APPLICATION DETAILS FOR SEALING EXPOSED EXTERIOR MASONRY SURFACES Unpainted exterior concrete, brick, cement plaster, stucco, or exposed aggregate should be waterproofed to protect the fabric of the structure from moisture, to control the growth of mildew on the surface and to reduce dirt pickup, staining and efflorescence. Mobile Paints offers four systems in this field. Two are solvent based; two are waterborne. All products are invisible when dry and do not affect the color or appearance of the masonry. None forms a measurable film. All repel water, causing to bead on the surface and run off while allowing moisture in the wall to evaporate. All reduce dirt pickup, staining and efflorescence. All are lead, chromate and mercury free. PRODUCTS DUB-L-TITE TM Silicone Waterproofing, Clear, 74-12 is a clear, 5% silicone solution for use on masonry only. Contains no wax and will not stain the surface. May be painted over with solvent-thinned masonry paints after curing. Meets the requirements of Federal Specification SS-W-110C. WEATHER-TITE TM Waterproofing Sealer, Clear, 74-7, is transparent and paintable. Contains no silicones, may be painted with oil or latex paints once dry. For use on masonry, brick, wood, canvas and fabrics. WEATHER-TITE TM H 2 O Dub-L-Tite Clear Waterproofing, 74-13, is a transparent, wax-free, waterborne silicone/silate waterproofing sealer for masonry surfaces. Can be painted with solvent thinned masonry paints after curing. WEATHER-TITE TM H 2 O Clear Waterproofing, 74-17, is a silicone-free, transparent, paintable waterproofing sealer for masonry, wood canvas and fabric. Can be painted with oil or latex paints after drying. APPLICATION DETAILS See Application Details for Painting Exterior Masonry Surfaces for Surface Preparation instructions. Application: Saturate surface thoroughly. Best applied with a low pressure sprayer but may be brushed or rolled. Surface should be saturated and running wet. Exterior Masonry Systems 6

01 EXTERIOR EXPOSED BLOCK OR CONCRETE MASONRY UNITS (CMU) 01.A Exterior Block, Unplastered, 100% Acrylic Latex Flat System Coat Product Premium Quality, Flat Finish VOC Sq Ft Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 40-Line WEATHER-TITE TM 100% Acrylic Flat 1.03 291 2 Finish 40-Line WEATHER-TITE TM 100% Acrylic Flat 1.03 291 2 Total Dry Mils 5 01.B Exterior Block, Unplastered, 100% Acrylic Latex Gloss System Coat Product Premium Quality, Gloss Finish VOC Sq Ft Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 140-Line WEATHER-TITE TM 100% Acrylic Gloss 1.99 296 2 Finish 140-Line WEATHER-TITE TM 100% Acrylic Gloss 1.99 296 2 Total Dry Mils 5 01.C Exterior Block, Unplastered, 100% Acrylic Latex Satin System Coat Product Premium Quality, Satin Finish VOC Sq Ft Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 240-Line WEATHER-TITE TM 100% Acrylic Satin 2.19 271 2 Finish 240-Line WEATHER-TITE TM 100% Acrylic Satin 2.19 271 2 Total Dry Mils 5 01.D Exterior Block, Unplastered, 100% Acrylic Latex High Gloss System Coat Product Premium Quality, Gloss Finish VOC Sq Ft Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 330-Line ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2 Finish 330-Line ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2 Total Dry Mils 5 Exterior Masonry Systems 7

01.E Exterior Block, Unplastered, Elastomeric 100% Acrylic System Coat Product Premium Quality, Eggshell Finish VOC Sq Ft Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 43-20 WEATHER-TITE TM Elastomeric Wall Coat 0.80 100 7.5 Finish 43-20 WEATHER-TITE TM Elastomeric Wall Coat 0.80 100 7.5 Total Dry Mils 16 01.F Exterior Block, Unplastered, Alkyd Gloss Enamel System Coat Product Premium Quality, Gloss Finish VOC Sq Ft Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 30-Line NAM-A-LAC Gloss Enamel 3.18 409 1.5 Finish 30-Line NAM-A-LAC Gloss Enamel 3.18 409 1.5 Total Dry Mils 4 01.G Exterior Block, Unplastered, Alkyd Gloss Enamel System Coat Product Premium Quality, Gloss Finish VOC Sq Ft Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 10-Line RUS-KIL Rust Inhibitive Enamel 3.35 385 2 Finish 10-Line RUS-KIL Rust Inhibitive Enamel 3.35 385 2 Total Dry Mils 5 01.H Exterior Block, Unplastered, High-Solids Semi-gloss Epoxy System Coat Product Premium Quality, Satin Finish VOC Sq Ft Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 613-Line MoPoxY TM HS High Solids Epoxy 2.00 374 3 Finish 613-Line MoPoxY TM HS High Solids Epoxy 2.00 374 3 Total Dry Mils 7 Exterior Masonry Systems 8

01.I Exterior Block, Unplastered, Catalyzed Polyurethane System Coat Product Premium Quality, Gloss Finish VOC Sq Ft Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 72-AW-21 MOTHANE HD Polyurethane Enamel (White) 4.11 268 2.5 Finish 72-AW-21 MOTHANE HD Polyurethane Enamel (White) 4.11 268 2.5 Total Dry Mils 6 01.J Exterior Block, Unplastered, Acrylic Latex Flat System Coat Product Professional Quality, Flat Finish VOC Sq Ft Mils Fill 260-45 ARCHITECTURAL Latex Block Filler 0.88 100 1 First 296-Line SMOOTH-COTE 100% Acrylic Flat 1.25 283 1.5 Finish 296-Line SMOOTH-COTE 100% Acrylic Flat 1.25 283 1.5 Total Dry Mils 4 01.K Exterior Block, Unplastered, Acrylic Latex Semi-Gloss System Coat Product Professional Quality, Semi-Gloss Finish VOC Sq Ft Mils Fill 260-45 ARCHITECTURAL Latex Block Filler 0.88 100 1 First 295-Line SMOOTH-COTE 100% Acrylic Semi-Gloss 2.54 335 1.5 Finish 295-Line SMOOTH-COTE 100% Acrylic Semi-Gloss 2.54 335 1.5 Total Dry Mils 4 01.L Exterior Block, Unplastered, 100% Acrylic Latex Gloss System Coat Product Professional Quality, Gloss Finish VOC Sq Ft Mils Fill 260-45 ARCHITECTURAL Latex Block Filler 0.88 100 1 First 294-Line SMOOTH-COTE 100% Acrylic Gloss 1.48 377 1.5 Finish 294-Line SMOOTH-COTE 100% Acrylic Gloss 1.48 377 1.5 Total Dry Mils 4 Exterior Masonry Systems 9

01.M Exterior Block, Unplastered, Vinyl Acrylic Latex Flat System Coat Product Professional Quality, Flat Finish VOC Sq Ft Mils Fill 260-45 ARCHITECTURAL Latex Block Filler 0.88 100 1 First 291-Line SMOOTH-COTE Vinyl Acrylic Flat 1.30 290 1.5 Finish 291-Line SMOOTH-COTE Vinyl Acrylic Flat 1.30 290 1.5 Total Dry Mils 4 02 EXTERIOR CEMENT PLASTER, STUCCO, CONCRETE, BRICK OR DRYWALL 02.A Exterior Masonry, Plaster and Drywall, Acrylic Latex Flat System Coat Product Premium Quality, Flat Finish VOC Feet Mils Prime 6-6 WEATHER-TITE TM Universal Primer 1.17 393 1.5 First 40-Line WEATHER-TITE TM 100% Acrylic Flat 1.03 291 2 Finish 40-Line WEATHER-TITE TM 100% Acrylic Flat 1.03 291 2 Total Dry Mils 5.5 02.B Exterior Masonry, Plaster and Drywall, Acrylic Latex Gloss System Coat Product Premium Quality, Gloss Finish VOC Feet Mils Prime 6-6 WEATHER-TITE TM Universal Primer 1.17 393 1.5 First 140-Line WEATHER-TITE TM 100% Acrylic Gloss 1.99 296 2 Finish 140-Line WEATHER-TITE TM 100% Acrylic Gloss 1.99 296 2 Total Dry Mils 5.5 02.C Exterior Masonry, Plaster and Drywall, Acrylic Latex Satin System Coat Product Premium Quality, Satin Finish VOC Feet Mils Prime 6-6 WEATHER-TITE TM Universal Primer 1.17 393 1.5 First 240-Line WEATHER-TITE TM 100% Acrylic Satin 2.19 271 2 Finish 240-Line WEATHER-TITE TM 100% Acrylic Satin 2.19 271 2 Total Dry Mils 5.5 Exterior Masonry Systems 10

02.D Exterior Masonry, Plaster and Drywall, Acrylic Latex Gloss System Coat Product Premium Quality, Gloss Finish VOC Sq Ft Mils Prime 6-6 WEATHER-TITE TM Universal Primer 1.17 393 1.5 First 330-Line ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2 Finish 330-Line ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2 Total Dry Mils 5.5 02.E Exterior Masonry, Plaster and Drywall, Elastomeric 100% Acrylic System Coat Product Premium Quality, Eggshell Finish VOC Sq Ft Mils Prime 6-6 WEATHER-TITE TM Universal Primer 1.17 393 1.5 First 43-20 WEATHER-TITE TM Elastomeric Wall Coat 0.80 100 7.5 Finish 43-20 WEATHER-TITE TM Elastomeric Wall Coat 0.80 100 7.5 Total Dry Mils 16.5 02.F Exterior Masonry, Plaster and Drywall, Alkyd Gloss Enamel System Coat Product Premium Quality, Gloss Finish VOC Sq Ft Mils Prime 6-6 WEATHER-TITE TM Universal Primer 1.17 393 1.5 First 30-Line NAM-A-LAC Gloss Enamel 3.18 409 1.5 Finish 30-Line NAM-A-LAC Gloss Enamel 3.18 409 1.5 Total Dry Mils 4.5 02.G Exterior Masonry, Plaster and Drywall, Alkyd Gloss Enamel System Coat Product Premium Quality, Gloss Finish VOC Sq Ft Mils Prime 6-6 WEATHER-TITE TM Universal Primer 1.17 393 1.5 First 10-Line RUS-KIL Rust Inhibitive Enamel 3.35 385 2 Finish 10-Line RUS-KIL Rust Inhibitive Enamel 3.35 385 2 Total Dry Mils 5.5 Exterior Masonry Systems 11

02.H Exterior Masonry, Plaster and Drywall, High-Solids Semi-gloss Epoxy System Coat Product Premium Quality, Semigloss Finish VOC Sq Ft Mils Prime 6-6 WEATHER-TITE TM Universal Primer 1.17 393 1.5 First 613-Line MoPoxY HS High Solids Epoxy 2.00 374 3 Finish 613-Line MoPoxY HS High Solids Epoxy 2.00 374 3 Total Dry Mils 7.5 02.I Exterior Masonry, Plaster and Drywall, High-Solids Epoxy/High Gloss Acrylic Epoxy System Coat Product Premium Quality, Gloss Finish* VOC Sq Ft Mils Prime 6-6 WEATHER-TITE TM Universal Primer 1.17 393 1.5 First 613-Line MoPoxY HS High Solids Epoxy 2.00 374 3 Finish 41-AW-2 MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 *Excellent Gloss Retention in Sunlight Total Dry Mils 6.5 02.J Exterior Masonry, Plaster and Drywall, Catalyzed Polyurethane System Coat Product Premium Quality, Gloss Finish VOC Sq Ft Mils Prime 6-6 WEATHER-TITE TM Universal Primer 1.17 393 1.5 First 72-AW-21 MOTHANE HD Polyurethane Enamel (White) 4.11 268 2.5 Finish 72-AW-21 MOTHANE HD Polyurethane Enamel (White) 4.11 268 2.5 Total Dry Mils 6.5 02.K Exterior Masonry, Plaster and Drywall, Acrylic Latex Flat System Coat Product Professional Quality, Flat Finish VOC Sq Ft Mils Prime 206-10 SMOOTH-COTE Acrylic Primer 1.48 387 1.5 First 296-Line SMOOTH-COTE 100% Acrylic Flat 1.25 283 1.5 Finish 296-Line SMOOTH-COTE 100% Acrylic Flat 1.25 283 1.5 Total Dry Mils 4.5 Exterior Masonry Systems 12

02.L Exterior Masonry, Plaster and Drywall, Acrylic Latex Semi-Gloss System Coat Product Professional Quality, Semi-Gloss Finish VOC Sq Ft Mils Prime 206-10 SMOOTH-COTE Acrylic Primer 1.48 387 1.5 First 295-Line SMOOTH-COTE 100% Acrylic Semi-Gloss 2.54 335 1.5 Finish 295-Line SMOOTH-COTE 100% Acrylic Semi-Gloss 2.54 335 1.5 Total Dry Mils 4.5 02.M Exterior Masonry, Plaster and Drywall, 100% Acrylic Latex Gloss System Coat Product Professional Quality, Gloss Finish VOC Sq Ft Mils Prime 206-10 SMOOTH-COTE Acrylic Primer 1.48 387 1.5 First 294-Line SMOOTH-COTE 100% Acrylic Gloss 1.48 377 1.5 Finish 294-Line SMOOTH-COTE 100% Acrylic Gloss 1.48 377 1.5 Total Dry Mils 4.5 02.N Exterior Masonry, Plaster and Drywall, Vinyl Acrylic Latex Flat System Coat Product Professional Quality, Flat Finish VOC Sq Ft Mils Prime 206-10 SMOOTH-COTE Acrylic Primer 1.48 387 1.5 First 291-Line SMOOTH-COTE Vinyl Acrylic Flat 1.30 290 1.5 Finish 291-Line SMOOTH-COTE Vinyl Acrylic Flat 1.30 290 1.5 Total Dry Mils 4.5 Exterior Masonry Systems 13

03 EXTERIOR EXPOSED PLASTER, CONCRETE OR BRICK, CLEAR SEALANT 03.A Exterior Exposed Concrete, Aggregate or Brick, Solvent-thinned Silicone Sealant System Coat Product Premium Quality - Clear, Non-Paintable VOC Sq Ft Mils Prime 74-12 WEATHER-TITE TM Dub-L-Tite Silicone Waterproofing 6.19 100 N/A Finish 74-12 WEATHER-TITE TM Dub-L-Tite Silicone Waterproofing 6.19 100 N/A Total Dry Mils N/A 03.B Exterior Exposed Concrete, Aggregate or Brick, Solvent-thinned Non-Silicone Sealant System Coat Product Premium Quality - Clear, Paintable VOC Sq Ft Mils Prime 74-7 WEATHER-TITE TM Waterproofing Sealer 5.30 100 N/A Finish 74-7 WEATHER-TITE TM Waterproofing Sealer 5.30 100 N/A Total Dry Mils N/A 03.C Exterior Exposed Concrete, Aggregate or Brick, Waterborne Silicone/Silane Sealant System Coat Product Premium Quality - Clear, Paintable w/ Solvent Thinned Paint after curing. VOC Sq Ft Mils Prime 74-13 WEATHER-TITE TM H 2 O Dub-L-Tite, Clear 0.00 100 N/A Finish 74-13 WEATHER-TITE TM H 2 O Dub-L-Tite, Clear 0.00 100 N/A Total Dry Mils N/A 03.D Exterior Exposed Concrete, Aggregate or Brick, Waterborne Non-Silicone Sealant System Also for wood canvas and fabric Coat Product Premium Quality - Clear, Paintable VOC Sq Ft Mils Prime 74-17 WEATHER-TITE TM H 2 O Waterproofing, Clear 0.68 100 N/A Finish 74-17 WEATHER-TITE TM H 2 O Waterproofing, Clear 0.68 100 N/A Total Dry Mils N/A Exterior Masonry Systems 14

SECTION 04 CONCRETE SECONDARY CONTENTION DIKE SYSTEMS The below systems have been used successfully in a variety of exposures. Please ask your BLP Mobile Paint Representative for recommendations for your specific requirements. 04.A Exterior Masonry, Catalyzed Epoxy System Coat Product Premium Quality - Semi-gloss Epoxy System VOC Sq Ft Mils Prime* 613-Line MoPoxY TM HS High Solids Epoxy 2.00 374 3 First 613-Line MoPoxY TM HS High Solids Epoxy 2.00 374 3 Finish 613-Line MoPoxY TM HS High Solids Epoxy 2.00 374 3 * Thin 10% with MoPoxY TM Brushing Thinner 75-35 Total Dry Mils 9 04.B Exterior Masonry, Catalyzed Epoxy/Acrylic Epoxy System** Coat Product Premium Quality-High Gloss Acrylic Epoxy Sys. VOC Sq Ft Mils Prime* 613-Line MoPoxY TM HS High Solids Epoxy 2.00 374 3 First 613-Line MoPoxY TM HS High Solids Epoxy 2.00 374 3 Finish 41-AW-2 MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 * Thin 10% with MoPoxY TM Brushing Thinner 75-35 **Excellent gloss retention under ultraviolet solar exposure Total Dry Mils 8 04.C Exterior Masonry, Catalyzed Epoxy Mastic / Polyurethane System Coat Product Premium Quality - High Gloss Finish VOC Sq Ft Mils Prime 41-AF-2 MoPoxY TM PRE-PREP Sealer, Clear 0.00 1604 1 First 40-AW-32 MoPoxY TM Mastic White 1.30 217 6 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 9 Exterior Masonry Systems 15

04.D Exterior Masonry, Catalyzed Epoxy, Epoxy Mastic System Coat Product Premium Quality - Gloss Finish VOC Sq Ft Mils Prime 41-AF-2 MoPoxY TM PRE-PREP Sealer, Clear 0.00 1604 1 First 40-AW-32 MoPoxY TM Mastic White 1.30 217 6 Finish 40-AW-32 MoPoxY TM Mastic White 1.30 217 6 Total Dry Mils 13 04.E Exterior Masonry, Catalyzed Epoxy, Epoxy Mastic, Acrylic Epoxy System* Coat Product Premium Quality - Gloss Finish VOC Sq Ft Mils Prime 41-AF-2 MoPoxY TM PRE-PREP Sealer, Clear 0.00 1604 1 First 40-AW-32 MoPoxY TM Mastic White 1.30 217 6 Finish 41-AW-2 MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 *Excellent gloss retention under ultraviolet solar exposure Total Dry Mils 9 SECTION 05 TRAFFIC ZONE MARKING ON CONCRETE AND ASPHALT PAVING AREAS 05.A Traffic Zone Marking on Concrete or Asphalt Paving Areas Coat Product Premium Quality - Matte Finish VOC Sq Ft Mils Finish 258-Line BLP LATEX Street Marking Paint 0.56 200 3 Application: Brush or roll: 3.8 mils DFT or 6 mils wet film thickness will yield a 4" stripe 600 feet long Spray: 9.3 mils DFT or 15 mils wet film thickness will yield a 4" stripe 300 feet long. This thickness is required when using as a binder for drop-on reflective glass beads. Exterior Masonry Systems 16

RECOMMENDED PAINTING SPECIFICATIONS FOR INTERIOR MASONRY SURFACES INDEX Index of Recommended Coating Systems for Interior Masonry Page 1-3 Each system includes prime or fill coat, first and second coats of compatible products. First, look for the substrate to be coated, then the type of finish desired Recommended Products Page 4-5 All products listed are recognized for their history of quality and service. Product data sheets and color cards are in the last section of this book Introduction - Recommended Painting Specifications Page 6-7 Surface Preparation SUGGESTED SYSTEMS Section 01 Interior Masonry, Plaster or Drywall Page 8-12 Section 02 Interior Block (Concrete Masonry Units) Unplastered Page 13-17 Interior Masonry Systems 1

RECOMMENDED COATING SYSTEMS FOR INTERIOR MASONRY INDEX Section 01 Interior Masonry, Plaster or Drywall Premium Quality - Residential, Commercial, Institutional & Industrial Service 01.A COVENTRY One coat Flat Wall Finish 01.B COVENTRY Semi-gloss Acrylic Enamel Finish 01.C COVENTRY Premium Eggshell Enamel Ffinish 01.D COVENTRY Acrylic High Gloss Enamel Finish 01.E ACR-A-LAC TM High Gloss Acrylic Enamel Finish 01.F H 2 O RUS-KIL DTM Acrylic Enamel Finish 01.G COVENTRY Lustarite Alkyd Satin-Gloss Finish 01.H NAM-A-LAC Alkyd Gloss Enamel Finish 01.I RUS-KIL Alkyd Rust Inhibitive Enamel Finish 01.J MoPoxY TM H2O-100 Waterborne Acrylic Epoxy High Gloss Finish 01.K MoPoxY TM H2O-200 Waterborne Amide Epoxy Semi-gloss Finish 01.L MoPoxY TM 513-Series High Gloss Amide Epoxy Finish 01.M MoPoxY TM Mastic / 513-Series High Gloss Amide Epoxy Finish 01.N MoPoxY TM 613-Series High Solids Semi-gloss Amide Epoxy Finish 01.O MoPoxY TM Mastic / 613-Series High Solids Semi-gloss Amide Epoxy Finish Professional Quality, Residential, Commerical, Instifutional & Light Industrial Service 01.P SMOOTH-COTE Interior Latex Flat Finish 01.Q SMOOTH-COTE Interior Latex Semi-gloss Finish 01.R SMOOTH-COTE Interior Acrylic Latex Eggshell Finish 01.S SMOOTH-COTE Interior Alkyd Semi-gloss Finish Interior Masonry Systems 2

Section 02 Interior Block (Concrete Masonry Units) Unplastered Premium Quality - Residential, Commercial, Institutional & Industrial Service 02.A COVENTRY One coat Flat Wall Finish 02.B COVENTRY Semi-gloss Acrylic Enamel Finish 02.C COVENTRY Premium Eggshell Enamel Ffinish 02.D COVENTRY Acrylic High Gloss Enamel Finish 02.E ACR-A-LAC TM High Gloss Acrylic Enamel Finish 02.F H 2 O RUS-KIL DTM Acrylic Enamel Finish 02.G COVENTRY Lustarite Alkyd Satin-Gloss Finish 02.H NAM-A-LAC Alkyd Gloss Enamel Finish 02.I RUS-KIL Alkyd Rust Inhibitive Enamel Finish 02.J MoPoxY TM H2O-100 Waterborne Acrylic Epoxy High Gloss Finish 02.K MoPoxY TM H2O-200 Waterborne Amide Epoxy Semi-gloss Finish 02.L MoPoxY TM 513-Series High Gloss Amide Epoxy Finish 02.M MoPoxY TM Mastic / 513-Series High Gloss Amide Epoxy Finish 02.N MoPoxY TM 613-Series High Solids Semi-gloss Amide Epoxy Finish 02.O MoPoxY TM Mastic / 613-Series High Solids Semi-gloss Amide Epoxy Finish Professional Quality - Residential, Commerical, Instifutional & Light Industrial Service 02.P SMOOTH-COTE Interior Latex Flat Finish 02.Q SMOOTH-COTE Interior Latex Semi-gloss Finish 02.R SMOOTH-COTE Interior Acrylic Latex Eggshell Finish 02.S SMOOTH-COTE Interior Alkyd Semi-gloss Finish Interior Masonry Systems 3

RECOMMENDED PRODUCTS FOR INTERIOR MASONRY SURFACES The below listing is representative of available products which may be used interchangeably within the designated systems depending upon conditions and desired service. Additional detail of product characteristics and application methods will be found in the referenced Product Data Sheets at the rear of this book. For specific recommendations, please consult your BLP Mobile Paint Representative. Number Description VOC Covers DFT Primers 6-6 WEATHER-TITE TM 100% Acrylic Universal Primer 1.17 393 1.50 19-7 COVENTRY PRYMALL 2 QD Acrylic Primer 0.96 302 1.50 219-19 SMOOTH-COTE Interior Latex Primer 1.13 283 1.50 206-10 SMOOTH-COTE Acrylic Primer 1.48 387 1.50 60-7 BLOC-FIL Latex Block Filler 0.55 100 1.00 260-45 Architectural Latex Block Filler 0.88 85-100 1.00 260-55 Architectural Latex Block Filler Brite White 0.70 85-100 1.00 Acrylic & Vinyl Waterborne Finishes 35-Series COVENTRY One Coat Flat Latex Wall Finish 0.83 375 1.50 1335-Series COVENTRY Semi-gloss Acrylic Enamel 2.00 345 1.50 2335-Series COVENTRY Premium Eggshell Enamel 0.86 375 1.50 335-Series COVENTRY Acrylic Latex High Gloss Enamel 1.09 408 1.50 330-Series ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2.00 310-Series H 2 O RUS-KIL DTM Acrylic Enamel 1.09 295 1.50 289-Series SMOOTH-COTE Interior Latex Flat Finish 0.89 346 1.50 290-Series SMOOTH-COTE Latex Semi-Gloss Enamel 1.60 252 1.50 292-Series SMOOTH-COTE Acrylic Latex Eggshell Enamel 0.85 395 0.50 Interior Masonry Systems 4

RECOMMENDED PRODUCTS FOR INTERIOR MASONRY SURFACES Alkyd Finishes 135-Series COVENTRY Lustarite Alkyd Satin Gloss Enamel 3.04 427 2.00 30-Series NAM-A-LAC Gloss Enamel 3.18 409 1.50 10-Series RUS-KIL Rust Inhibitive Gloss Enamel 3.35 385 2.00 50-Series SpeeDeck Polyurethane Enamel 3.35 388 2.00 520-Series QD-520 Quick Dry Enamel (OEM) 4.07 417 1.50 521-Series QD-521 Quick Dry Enamel 3.72 467 1.50 293-Series SMOOTH-COTE Alkyd Semi-gloss Enamel 2.85 449 2.00 Catalyzed Epoxies & Epoxy Mastic 613-Line MoPoxY TM HS High Solids Semi-gloss Epoxy 2.00 374 3.00 513-Line MoPoxY TM High Gloss Epoxy 4.30 314 2.00 69-AW-5 MoPoxY TM H2O-100 Waterborne Acrylic Epoxy, Gloss 1.71 313 2.00 69-AW-6 MoPoxY TM H2O-200 Waterborne Epoxy, Semi-gloss 1.00 225 3.00 40-AW-32 MoPoxY TM MASTIC, White 1.30 217 6.00 41-AF-2 MoPoxY TM Pre-Prep Sealer, Clear 0.00 1604 1.00 41-AW-2 MOPOX-ACRYL Acrylic Epoxy, High Gloss 3.50 409 2.00 Interior Masonry Systems 5

RECOMMENDED PAINTING SPECIFICATIONS FOR INTERIOR MASONRY SURFACES Mobile Paints was founded in Mobile, Alabama, in 1921 and was originally dedicated to formulating top-quality architectural, industrial and marine coatings for the Gulf Coast s tropical and subtropical climates. Subsequently, we have expanded our geographical horizon to include more northern regions and are recognized for the high quality and durability of our products throughout our market area. This section includes recommended coating systems for interior masonry surfaces including brick, plaster, and gypsum board walls and ceilings as well as unplastered cement block or concrete masonry units (CMU), in residential, commercial, institutional and industrial service. Each coating system details the primer, intermediate, and finish coats and is suitable for residential, commercial, institutional and industrial service as indicated. In addition to the usual latex, acrylic and alkyd finishes, we include a variety of catalyzed epoxy systems for clean rooms in pharmaceutical plants, food processing plants, and areas subject to frequent wetting, such as car washes and showers. All products are lead-free, chromate-free, mercury-free, and VOC compliant. SURFACE PREPARATION Proper surface preparation is essential to the life of any coating system. All masonry surfaces should be allowed to cure for at least 30 days before painting. Surfaces should be clean, dry, and free from dust, laitance, and mold release oil. Gypsum board should be dusted thoroughly to remove sanding dust. Seal openings around door jams and windows with WEATHER- TITE TM Premium 100 Siliconized Acrylic Caulk. Bare or unplastered block (CMU) should be filled with either BLOC-FIL Latex Block Filler, 60-7, for normal service or BLOC-SEAL TM Acrylic, 19-10, for service in areas subject to frequent washing or wetting. Previously painted surfaces must be clean and dry. Scrape and sand peeling or flaking paint to provide a sound surface. Sand high gloss finishes to insure good intercoat adhesion. Prime bare areas with one coat of COVENTRY PRYMALL 2 Q D Acrylic Primer, 19-7, 1.5 mils dry. Consult your BLP Mobile Paint Representative for recommendations for specific requirements. Interior Masonry Systems 6

RECOMMENDED PAINTING SPECIFICATIONS FOR INTERIOR COATING SYSTEMS All systems are based on our top-quality products and are generally organized in order of increasing chemical and abrasion resistance. All products are lead-free, chromate-free, mercury-free, and VOC compliant. All products may be applied by brush, roller, or airless or conventional spray. COVENTRY is the brand name for our first line interior primers and finishes which are available in flat, eggshell, semigloss and high gloss latex acrylic coatings and enamels; alkyd satin-gloss enamel, and acrylic primers for wood and masonry. In addition to our famous Southern White Collection of whites, these are available in an almost unlimited range of custom colors though our Color Studio system. NAM-A-LAC is the brand name of our first line high gloss alkyd enamels. Non-toxic, self-leveling, fast-dry, they are available in a wide range of stock colors as well as an extensive palette of custom colors and are formulated for interior and exterior service. ACR-A-LAC TM is the brand name for our line of waterborne high gloss acrylic enamels, which share the same color card with our NAM-A-LAC line. 100% acrylic, they have superior gloss and color retention and are excellent for residential, institutional, commercial and light industrial service. Low odor, low VOC, fast drying, they are suitable for interior and exterior service. RUS-KIL is the brand name for our line of rust-inhibiting alkyd enamels for residential, institutional, commercial and industrial service. These are stocked in White, Black, OSHA Safety Colors, and Industrial colors as shown on the RUS-KIL color card, and are also available in a wide range of custom colors. Suitable for interior and exterior service. H 2 O RUS-KIL is the brand name for our DTM waterborne high gloss acrylic enamels which share the standard RUS-KIL color card. 100% acrylic, they have superior gloss and color retention. Low odor, low VOC, fast drying, they are excellent for interior or exterior service. MoPoxY TM is the brand name for our extensive line of catalyzed epoxies, offering formulations for institutional, commercial, and industrial coating systems where maximum protection and durability are required. Both standard and waterborne formulations are available. In addition to an extensive color card, a wide range of custom colors are shaded to order. MoPoxY TM offers superior resistance to chemicals, especially alkalis, moisture, and abrasion, and good resistance to most solvents and acid splashes. Special formulations are stocked for use in food processing plants, kitchens, pharmaceutical plants and other areas where direct food contact certification is required. Recommended for use in schools, hospitals, laundries, shopping centers, kitchens and food processing areas, chemical and pharmaceutical plants, waste water treatment plants, potable water storage tanks, and other industrial and commercial installations. Formulations are available for specific chemical or food product resistance requirements. Please ask your BLP Mobile paint representative for assistance in meeting your coating needs. SMOOTH-COTE is our brand name for our Professional Line of interior and exterior primers and finishes. Interior Masonry Systems 7

SECTION 01 INTERIOR MASONRY, PLASTER AND DRYWALL 01.A Latex Flat Finish, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 35-Series COVENTRY One Coat Flat Wall Finish 0.83 375 1.5 Finish 35-Series COVENTRY One Coat Flat Wall Finish 0.83 375 1.5 Total Dry Mils 4.5 01.B Acrylic Semi-gloss Finish, Residential, Commercial & Light Industrial Service Coat Product Premium Quality, 100% Acrylic Latex VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 1335-Series COVENTRY Semi-gloss Acrylic Enamel 2.00 345 1.5 Finish 1335-Series COVENTRY Semi-gloss Acrylic Enamel 2.00 345 1.5 Total Dry Mils 4.5 01.C Acrylic Eggshell Finish, Residential, Commercial & Light Industrial Service Coat Product Premium Quality, 100% Acrylic Latex VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 2335-Series COVENTRY Premium Eggshell Enamel 0.86 375 1.5 Finish 2335-Series COVENTRY Premium Eggshell Enamel 0.86 375 1.5 Total Dry Mils 4.5 01.D Acrylic High Gloss Finish, Residential, Commercial & Light Industrial Service Coat Product Premium Quality, 100% Acrylic Latex VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 335-Series COVENTRY Latex High Gloss Enamel 1.09 408 1.5 Finish 335-Series COVENTRY Latex High Gloss Enamel 1.09 408 1.5 Total Dry Mils 4.5 Interior Masonry Systems 8

01.E Acrylic High-Gloss Enamel, Residential, Commercial & Light Industrial Service Coat Product Premium Quality, 100% Acrylic Latex VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 330-Series ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2 Finish 330-Series ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2 Total Dry Mils 5.5 01.F Acrylic High-Gloss Enamel Finish, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 310-Series H 2 O RUS-KIL DTM Acrylic Enamel 1.09 295 2 Finish 310-Series H 2 O RUS-KIL DTM Acrylic Enamel 1.09 295 2 Total Dry Mils 5.5 01.G Alkyd Semi-Gloss Enamel System Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 135-Series COVENTRY Lustarite Satin-Gloss Enamel 3.04 427 2 Finish 135-Series COVENTRY Lustarite Satin-Gloss Enamel 3.04 427 2 Total Dry Mils 5.5 01.H Alkyd Gloss Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 30-Series NAM-A-LAC Gloss Enamel 3.18 409 1.5 Finish 30-Series NAM-A-LAC Gloss Enamel 3.18 409 1.5 Total Dry Mils 4.5 Interior Masonry Systems 9

01.I Alkyd Gloss Enamel System, Residential, Commercial & Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 10-Series RUS-KIL Rust Inhibitive Enamel 3.35 385 2 Finish 10-Series RUS-KIL Rust Inhibitive Enamel 3.35 385 2 Total Dry Mils 5.5 01.J Waterborne Acrylic Gloss Epoxy Finish, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 69-AW-5 MoPoxY TM H 2 0-100 Acrylic Epoxy 1.71 313 2 Finish 69-AW-5 MoPoxY TM H 2 0-100 Acrylic Epoxy 1.71 313 2 Total Dry Mils 5.5 01.K Waterborne Amide Epoxy System, Commercial & Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 69-AW-6 MoPoxY TM H 2 0-200 WB Amide Epoxy 1.00 225 3 Finish 69-AW-6 MoPoxY TM H 2 0-200 WB Amide Epoxy 1.00 225 3 Total Dry Mils 7.5 01.L Amide Gloss Epoxy System, Commercial & Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 513-Series MoPoxY TM High Gloss Epoxy 4.24 322 2 Finish 513-Series MoPoxY TM High Gloss Epoxy 4.24 322 2 Total Dry Mils 5.5 Interior Masonry Systems 10

01.M Epoxy Mastic/Amide Gloss Epoxy System, Commercial & Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 40-AW-32 MoPoxY TM Mastic White 1.30 217 6 Second 513-Series MoPoxY TM High Gloss Epoxy 4.24 322 2 Finish 513-Series MoPoxY TM High Gloss Epoxy 4.24 322 2 Total Dry Mils 11.5 01.N High-solids Amide Semi-Gloss Epoxy System, Commercial & Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 613-Series MoPoxY TM HS High Solids Epoxy 2.00 374 3 Finish 613-Series MoPoxY TM HS High Solids Epoxy 2.00 374 3 Total Dry Mils 7.5 01.O Epoxy Mastic/Semi-Gloss Epoxy System, Heavy Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 19-7 PRYMALL 2 Q D Acrylic Primer 0.96 302 1.5 First 40-AW-32 MoPoxY TM Mastic White 1.30 217 6 Second 613-Series MoPoxY TM HS High Solids Epoxy 2.00 374 3 Finish 613-Series MoPoxY TM HS High Solids Epoxy 2.00 374 3 Total Dry Mils 13.5 01.P Latex Flat Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 219-19 SMOOTH-COTE Interior Latex Primer 1.13 283 1.5 First 289-Series SMOOTH-COTE Interior Latex Flat 0.89 346 1.5 Finish 289-Series SMOOTH-COTE Interior Latex Flat 0.89 346 1.5 Total Dry Mils 4.5 Interior Masonry Systems 11

01.Q Latex Semi-Gloss Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 219-19 SMOOTH-COTE Interior Latex Primer 1.13 283 1.5 First 290-Series SMOOTH-COTE Latex Semi-Gloss 1.60 252 1.5 Finish 290-Series SMOOTH-COTE Latex Semi-Gloss 1.60 252 1.5 Total Dry Mils 4.5 01.R Latex Acrylic Eggshell Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 219-19 SMOOTH-COTE Interior Latex Primer 1.13 283 1.5 First 292-Series SMOOTH-COTE Acrylic Latex Eggshell 0.85 395 1.5 Finish 292-Series SMOOTH-COTE Acrylic Latex Eggshell 0.85 395 1.5 Total Dry Mils 4.5 01.S Alkyd Semi-gloss Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 219-19 SMOOTH-COTE Interior Latex Primer 1.13 283 1.5 First 293-Series SMOOTH-COTE Alkyd Semi-Gloss 2.85 449 2 Finish 293-Series SMOOTH-COTE Alkyd Semi-Gloss 2.85 449 2 Total Dry Mils 5.5 Interior Masonry Systems 12

SECTION 02 INTERIOR BLOCK (CONCRETE MASONRY UNITS) UNPLASTERED 02.A Latex Flat Finish, Residential & Commercial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 35-Series COVENTRY One Coat Flat Wall Finish 0.83 375 1.5 Finish 35-Series COVENTRY One Coat Flat Wall Finish 0.83 375 1.5 Total Dry Mils 4.0 02.B Acrylic Semi-Gloss Finish, Residential, Commercial, Institutional & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 1335-Series COVENTRY Semi-gloss Acrylic Enamel 2.00 345 1.5 Finish 1335-Series COVENTRY Semi-gloss Acrylic Enamel 2.00 345 1.5 Total Dry Mils 4.0 02.C Acrylic Eggshell Finish, Residential, Commercial, Institutional & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 2335-Series COVENTRY Premium Eggshell Enamel 0.86 375 1.5 Finish 2335-Series COVENTRY Premium Eggshell Enamel 0.86 375 1.5 Total Dry Mils 4.0 02.D Acrylic Gloss Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 335-Series COVENTRY Latex Acrylic High Gloss Enamel 1.09 408 1.5 Finish 335-Series COVENTRY Latex Acrylic High Gloss Enamel 1.09 408 1.5 Total Dry Mils 4.0 Interior Masonry Systems 13

02.E Acrylic Gloss Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 330-Series ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2 Finish 330-Series ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2 Total Dry Mils 5.0 02.F Acrylic Gloss Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 310-Series H 2 O RUS-KIL Acrylic DTM Enamel 1.09 295 2 Finish 310-Series H 2 O RUS-KIL Acrylic DTM Enamel 1.09 295 2 Total Dry Mils 5.0 02.G Alkyd Semi-Gloss Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 135-Series COVENTRY Lustarite Satin-Gloss Enamel 3.04 427 2 Finish 135-Series COVENTRY Lustarite Satin-Gloss Enamel 3.04 427 2 Total Dry Mils 5.0 02.H Alkyd Gloss Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-07 BLOC-FIL Latex Block Filler 0.55 100 1 First 30-Series NAM-A-LAC Gloss Enamel 3.18 409 1.5 Finish 30-Series NAM-A-LAC Gloss Enamel 3.18 409 1.5 Total Dry Mils 4.0 Interior Masonry Systems 14

02.I Alkyd Gloss Enamel System, Commercial & Industrial Service Coat Product Premium Industrial Quality VOC Sq. Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 10-Series RUS-KIL Gloss Enamel 3.35 385 2 Finish 10-Series RUS-KIL Gloss Enamel 3.35 385 2 Total Dry Mils 5.0 02.J Waterborne Acrylic Gloss Epoxy Finish, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 69-AW-5 MoPoxY TM H20-100 WB Acrylic Epoxy 1.71 313 2 Finish 69-AW-5 MoPoxY TM H20-100 WB Acrylic Epoxy 1.71 313 2 Total Dry Mils 5.0 02.K Waterborne Amide Epoxy System, Commercial & Industrial Service Coat Product Premium Quality VOC Sq. Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 69-AW-6 MoPoxY TM H20-200 WB Amide Epoxy 1.00 225 3 Finish 69-AW-6 MoPoxY TM H20-200 WB Amide Epoxy 1.00 225 3 Total Dry Mils 7.0 02.L Amide Gloss Epoxy System, Commercial & Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 513-Series MoPoxY TM High GlossEpoxy 4.30 314 2 Finish 513-Series MoPoxY TM High GlossEpoxy 4.30 314 2 Total Dry Mils 5.0 Interior Masonry Systems 15

02.M Epoxy Mastic/High Gloss Epoxy System, Heavy Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 40-AW-32 MoPoxY TM MASTIC White 1.30 217 6 Second 513-Series MoPoxY TM High GlossEpoxy 4.30 314 2 Finish 513-Series MoPoxY TM High GlossEpoxy 4.30 314 2 Total Dry Mils 11.0 02.N High-solids Amide Semi-Gloss Epoxy System, Commercial & Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 613-Series MoPoxY TM HS High Solids Epoxy 2.00 374 3 Finish 613-Series MoPoxY TM HS High Solids Epoxy 2.00 374 3 Total Dry Mils 7.0 02.O Epoxy Mastic/Semi-Gloss Epoxy System, Heavy Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 First 40-AW-32 MoPoxY TM MASTIC White 1.30 217 6 Second 613-Series MoPoxY TM HS High Solids Epoxy 2.00 374 3 Finish 613-Series MoPoxY TM HS High Solids Epoxy 2.00 374 3 Total Dry Mils 13.0 02.P Latex Flat Finish, Residential & Commercial Service Coat Product Professional Quality VOC Feet Mils Prime 260-45 ARCHITECTURAL Block Filler 0.88 85 1 First 289-Series SMOOTH-COTE Interior Latex Flat 0.89 346 1.5 Finish 289-Series SMOOTH-COTE Interior Latex Flat 0.89 346 1.5 Total Dry Mils 4.0 Interior Masonry Systems 16

02.Q Latex Semi-Gloss Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 260-45 ARCHITECTURAL Block Filler 0.88 85 1 First 290-Series SMOOTH-COTE Latex Semi-Gloss 1.60 252 1.5 Finish 290-Series SMOOTH-COTE Latex Semi-Gloss 1.60 252 1.5 Total Dry Mils 4.0 02.R Latex Acrylic Eggshell Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 260-45 ARCHITECTURAL Block Filler 0.88 85 1 First 292-Series SMOOTH-COTE Acrylic Latex Eggshell 0.85 395 1.5 Finish 292-Series SMOOTH-COTE Acrylic Latex Eggshell 0.85 395 1.5 Total Dry Mils 4.0 02.S Alkyd Semi-gloss Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 260-45 ARCHITECTURAL Block Filler 0.88 85 1 First 293-Series SMOOTH-COTE Alkyd Semi-Gloss 2.85 449 2 Finish 293-Series SMOOTH-COTE Alkyd Semi-Gloss 2.85 449 2 Total Dry Mils 5.0 Interior Masonry Systems 17

RECOMMENDED PAINTING SPECIFICATIONS FOR WOOD SURFACES Please see section on FLOORS for Floor Finishing Systems INDEX OF COATING SYSTEMS Detailed Index of Coating Systems INTRODUCTION Page 3 Discussion of surface preparation and product advantages COATING SYSTEMS Page 7 Recommended Primers, Intermediate Coats, Finish Coats, Dry Film Thickness and Coverage 01 - Interior, Natural Grain 02 - Interior, Painted Finishes 03 - Exterior, Natural Grain 04 - Exterior, Painted Finishes PRODUCT DATA SHEETS & COLOR CARDS Will be found in the last section of this book Wood Finishing Specifications 1

RECOMMENDED SPECIFICATIONS FOR WOOD FINISHING Well-finished wood is the hallmark of elegance. Interior wood may be oiled, stained, varnished, or lacquered for a natural finish to display its grain and beauty, or painted to match or contrast with adjoining wall surfaces. Fire retardant systems are included for Class A fire protection. Exterior wood should always be protected from the weather. Even cedar, cypress and redwood benefit from a clear waterproofing to repel water and protect against rot. Clear oil sealers, oil and acrylic stains, and marine varnishes combine the beauty of a natural finish with protection. New waterborne sealants are now available and included in this specification. Traditional coating systems include oil based house paints and enamels and a full line of waterborne acrylic latex paints and enamels which offer exceptional gloss and color retention. Marine varnishes and silicone alkyd enamels offer extra protection and durability in marine and industrial environments. Catalyzed epoxies, both solvent-thinned and waterborne, offer excellent abrasion and chemical resistance. Mobile Paints manufactures a wide variety of finishes for wood, both for interior and exterior, for residential, commercial, institutional, industrial and marine service. In the interests of simplification, we have limited our recommendations to the most widely used systems which have a long record of user satisfaction, and detail these below. All recommended finishes are lead-free, chromate-free, mercury-free and VOC compliant. All are available in a wide palette of colors. Floor finishes are covered in a separate section under FLOORS. Please ask your BLP Mobile Paint representative for specific recommendations. Wood Finishing Specifications 2

INTERIOR SURFACE PREPARATION Surface preparation is the same for all woods, independent of the finish to be applied. Fill any nail holes with matching color putty. Sand lightly to remove any irregularities. Dust with tack cloth to remove all dust. Surface must be clean, dry and dust-free. RECOMMENDED INTERIOR WOOD FINISHES All products recommended are lead-free, mercury-free, chromate-free and VOC compliant. NUWOOD Penetrating Wood Finish, 71-Series - A premium quality polyurethane wood stain and finish for interior wood and wood products. Excellent as a stain and sealer where a natural wood grain finish is desired. Available in a wide variety of standard and custom colors. May be finished with NUWOOD Polyurethane Varnish, 72-Series, or NUWOOD Tung Oil Finish, 72-45. NUWOOD Polyurethane Varnish - A clear, pale varnish with excellent resistance to abrasion, water, mild acids and alkalis, grease, alcohol and soil. Available in gloss, 72-35, and satin-gloss, 72-36, finishes. May be applied directly to wood or over polyurethane stain. Suitable for use on all interior woodwork including floors NUWOOD Tung Oil Finish 72-45 - A clear, hand-rubbed finish with excellent resistance to water spotting, alcohol, grease and abrasion. Excellent for paneling, doors, cabinets and furniture. Not recommended for floors. CLEARCOAT II, 9835-241, is a Class A, interior, fire protective varnish. May be applied over existing varnishes or primers and topcoated with NUWOOD Polyurethane Varnish for additional protection. BLP Spraying Lacquer, 9835 Series - Quick dry, water-white, non-yellowing, with a complimentary line of lacquer stains for natural wood finishes. Also available in tint bases for an almost unlimited range of colors. Excellent for kitchen cabinets, furniture, paneling, doors and door frames and trim. Apply by spray only. Not recommended for floors. COVENTRY is the brand name for our premium line of interior wall finishes and primers. Finishes are available in One-Coat Flat Wall Finish, 35-Series; Semi-gloss Acrylic Enamel, 1335-Series; Eggshell Acrylic Enamel, 2335-Series; and High Gloss Acrylic Enamel, 335-Series. Excellent coverage, easy to apply, quick-drying, odorless, with a wide range of colors. Washable, easily maintained. COVENTRY Lustarite, 135-Series - a complimentary alkyd satin-gloss enamel. Excellent coverage, easy to apply, quick drying, low odor, with a wide range of colors.. Washable, easily maintained. Recommended for areas subject to moderate soiling, abrasion or light chemical exposure. Wood Finishing Specifications 3

ACR-A-LAC TM 100% Acrylic Gloss Enamel, 330-Series - high gloss, low odor, 100% acrylic, with excellent coverage, easy to apply, quick drying. Shares color card with NAM-A-LAC Alkyd Gloss enamel and is also available in with a wide range of custom colors. Washable, easily maintained. Recommended for areas subject to moderate soiling, abrasion or chemical exposure. Suitable for interior and exterior service. NAM-A-LAC Alkyd Gloss Enamel, 30-Series - excellent coverage, easy to apply, quick drying, low odor. Shares color card with ACR-A-LAC TM and is also available in a wide range of custom colors. Washable, easily maintained. Recommended for areas subject to moderate soiling, abrasion or chemical exposure. Suitable for interior and exterior service. RUS-KIL Rust Inhibiting Alkyd Gloss Enamel, 10-Series - an industrial grade general purpose enamel suitable for interior and exterior service on a variety of surfaces. Available in OSHA Safety Colors and other standard colors as shown on the RUS-KIL color card and a wide variety of custom colors. H 2 O RUS-KIL DTM 100% Acrylic Gloss Enamel, 310-Series - high gloss, low odor, 100% acrylic, with excellent coverage, easy to apply, quick drying. Available in OSHA Safety Colors and other standard colors as shown on the RUS-KIL color card as well as a wide range of custom colors. Washable, easily maintained. Recommended for areas subject to light to moderate soiling, abrasion or chemical exposure. Suitable for interior and exterior service. FIRECOAT 320, 9835-239 - A Class A, Underwrites Laboratories Classified, interior latex fire protective coating. May be applied to wood, drywall or fiberglass over a suitable primer or other commercial latex based product. White. Custom pastels are available. May be topcoated with any of the above finish products. MOPOXY TM Catalyzed Epoxy - superior resistance to chemicals, especially alkalis, and abrasion. Good resistance to most solvents, acid splashes. Available in a wide range of formulations for specific services, including direct food contact. Extensive palette of colors. Recommended for use in schools, hospitals, kitchens and food processing areas, chemical and pharmaceutical plants, and other commercial, institutional and industrial installations. where a durable and easily maintained finish is required. Waterborne formulations available. Please see your BLP Mobile Paint representative for specific recommendations. SMOOTH-COTE is Mobile s brand name for our line of Professional primers and coatings and is available in Flat, Semigloss, and Satin Latex and Semi-gloss Alkyd finishes for interior service.. Wood Finishing Specifications 4

EXTERIOR SURFACE PREPARATION Fill any nail holes with matching color putty. Sand lightly to remove any irregularities. Dust with tack cloth to remove all dust. Caulk all joints and openings with WEATHER-TITE TM Premium 100 Siliconized Acrylic Caulking in desired color. Mildew and stains should be removed by washing with a solution of Jomax, Clorox and Trisodium Phosphate as directed on the Jomax label. Clean with high pressure water if necessary to remove chalking paint and other contamination. Surface must be clean, dry and dust free. RECOMMENDED EXTERIOR WOOD FINISHES WEATHER PROTECTOR Exterior Clear Sealer & Preservative, 7-10 - A transparent penetrating sealer with mildewcide and ultraviolet screening agents to help new lumber retain its natural look. May be tinted. WEATHER-TITE Waterproofing Sealer, Clear, 74-7 - A transparent, paintable, waterproofing sealer for masonry, concrete, brick, stucco, wood, and canvas. Contains no silicones. Prevents water penetration while allowing surface to breathe. May be painted when dry. WEATHER-TITE H20 Waterproofing Sealer, Clear. 74-17 - A transparent, paintable waterproofing sealer. Waterborne. Contains no silicones. Suitable for use on most porous surfaces such as masonry, wood, canvas and fabric. Prevents water penetration while allowing the treated surface to breathe. WEATHER PROTECTOR Interior/Exterior Acrylic Wood Stain, 44 Line - A 100% acrylic latex waterborne solid hide stain suitable for interior and exterior use. Available in stock colors, custom colors, and a semitransparent formulation. May be varnished for interior service. Contains an effective mildewcide. JACK TAR 100% Phenolic Marine Spar Varnish, 470-31 - A clear, high gloss marine varnish for industrial, commercial and residential use on exterior exposed wood or metal surfaces JACK TAR Marine Spar Varnish with Ultraviolet Filter, 470-34 - A 100% phenolic high gloss clear finish containing an effective ultraviolet filter. For exterior weather-exposed wood surfaces such as doors, wood trim, hatches, transoms, decks, paneling and spars. WEATHER-TITE TM Southernized Mildew Treated House Paint, 5 Line - An oil based exterior house paint formulated to withstand extreme temperatures and excessive humidity as well as mild chemical fumes and salt air. Contains an effective mildewcide. Wide range of colors, excellent color retention. Wood Finishing Specifications 5

WEATHER-TITE TM 100% Alkyd Universal Primer, 6-6 - A high quality 100% acrylic latex primer for interior or exterior use on wood, masonry, galvanized metal and aluminum. Contains effective mildewcides. Prevents bleeding of many stains. Fast drying, low odor, easy to apply. ACR-A-LAC TM 100% Acrylic Gloss Enamel, 330-Series - high gloss, low odor, 100% acrylic, with excellent coverage, easy to apply, quick drying. Shares color card with NAM-A-LAC Alkyd Gloss enamel and is also available in with a wide range of custom colors. Washable, easily maintained. Recommended for areas subject to moderate soiling, abrasion or chemical exposure. Suitable for interior and exterior service. NAM-A-LAC Alkyd Gloss Enamel, 30-Series - excellent coverage, easy to apply, quick drying, low odor. Shares color card with ACR-A-LAC TM and is also available in a wide range of custom colors. Washable, easily maintained. Recommended for areas subject to moderate soiling, abrasion or chemical exposure. Suitable for interior and exterior service. RUS-KIL Rust Inhibiting Alkyd Gloss Enamel, 10-Series - an industrial grade general purpose enamel suitable for interior and exterior service on a variety of surfaces. Available in OSHA Safety Colors and other standard colors as shown on the RUS-KIL color card and a wide variety of custom colors. H 2 O RUS-KIL DTM 100% Acrylic Gloss Enamel, 310-Series - high gloss, low odor, 100% acrylic, with excellent coverage, easy to apply, quick drying. Available in OSHA Safety Colors and other standard colors as shown on the RUS-KIL color card as well as a wide range of custom colors. Washable, easily maintained. Recommended for areas subject to light to moderate soiling, abrasion or chemical exposure. Suitable for interior and exterior service. JACK TAR Silicone Yacht Finish, 432-Series - a high gloss silicone alkyd enamel with excellent gloss and color retention in marine and industrial environments. SMOOTH-COTE is our brand name for a complete line of professional quality alkyd and latex architectural primers and coatings for interior and exterior service Wood Finishing Specifications 6

01 INTERIOR WOOD FINISHES, NATURAL GRAIN 01.A Interior Wood, Natural, Gloss Polyurethane Varnish System Coat Product Premium Quality VOC Sq.Ft. Mils Prime 71-Line NUWOOD Penetrating Wood Stain 4.61 750 1.00 First 72-35 NUWOOD Polyurethane Gloss Finish 3.77 673 1.00 Finish 72-35 NUWOOD Polyurethane Gloss Finish 3.77 673 1.00 01.B Interior Wood, Natural, Satin-Gloss Polyurethane Varnish System Total Dry Mils 3.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime 71-Line NUWOOD Penetrating Wood Stain 4.61 750 1.00 First 72-36 NUWOOD Polyurethane Satin Finish 3.77 558 1.00 Finish 72-36 NUWOOD Polyurethane Satin Finish 3.77 558 1.00 01.C Interior Wood, Natural, Rubbed Tung Oil Finish Total Dry Mils 3.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime 72-45 NUWOOD Tung Oil Finish 4.51 502 1.00 First 72-45 NUWOOD Tung Oil Finish 4.51 502 1.00 Finish 72-45 NUWOOD Tung Oil Finish 4.51 502 1.00 01.D FIRE RETARDANT Varnish System Total Dry Mils 3.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime 9835-241 CLEARCOAT II Fire Retardant Varnish 4.19 135 5.00 First 9835-241 CLEARCOAT II Fire Retardant Varnish 4.19 135 5.00 Finish with any of the above finish coats Please ask your BLP Mobile Paint service representative for details Total Dry Mils 10.00 Wood Finishing Specifications 7

01.E Interior Wood, Natural, Gloss Lacquer System Coat Product Premium Quality VOC Sq.Ft. Mils Prime 9835-165 Lacquer Sanding Sealer Water-White 152 1.00 First 9835-098 Clear Lacquer, Water-White, Gloss 205 0.80 Second 9835-098 Clear Lacquer, Water-White, Gloss 205 0.80 Finish 9835-098 Clear Lacquer, Water-White, Gloss 205 0.80 01.F Interior Wood, Natural, Satin-Gloss Lacquer System Total Dry Mils 3.40 Coat Product Premium Quality VOC Sq.Ft. Mils Prime 9835-165 Lacquer Sanding Sealer Water-White 152 1.00 First 9835-100 Clear Lacquer, Water-White, Satin 205 0.80 Second 9835-100 Clear Lacquer, Water-White, Satin 205 0.80 Finish 9835-100 Clear Lacquer, Water-White, Satin 205 0.80 02 INTERIOR WOOD, PAINTED FINISHES Total Dry Mils 3.40 02.A Interior Wood, Vinyl Latex Flat Finish. Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 319-8 COVENTRY Acrylic Enamel Undercoat 0.76 351 1.50 First 35-Series COVENTRY Flat Wall Finish 0.83 375 1.50 Finish 35-Series COVENTRY Flat Wall Finish 0.83 375 1.50 Total Dry Mils 4.50 02.B Interior Wood, Acrylic Latex Eggshell Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 319-8 COVENTRY Acrylic Enamel Undercoat 0.76 351 1.50 First 2335-Series COVENTRY Premium Eggshell Enamel 0.86 375 1.50 Finish 2335-Series COVENTRY Premium Eggshell Enamel 0.86 375 1.50 Total Dry Mils 4.50 Wood Finishing Specifications 8

02.C Interior Wood, Acrylic Latex Semi-Gloss Enamel System Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 319-8 COVENTRY Acrylic Enamel Undercoat 0.76 351 1.50 First 1335-Line COVENTRY Semi-gloss Acrylic Enamel 2.00 345 1.50 Finish 1335-Line COVENTRY Semi-gloss Acrylic Enamel 2.00 345 1.50 Total Dry Mils 4.50 02.D Interior Wood, Acrylic High Gloss Enamel System Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 319-8 COVENTRY Acrylic Enamel Undercoat 0.76 351 1.50 First 335-Series COVENTRY Acrylic High Gloss Enamel 1.09 408 1.50 Finish 335-Series COVENTRY Acrylic High Gloss Enamel 1.09 408 1.50 Total Dry Mils 4.50 02.E Interior Wood, 100% Acrylic Gloss Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 319-8 COVENTRY Acrylic Enamel Undercoat 0.76 351 1.50 First 330-Series ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2.00 Finish 330-Series ACR-A-LAC TM 100% Acrylic Gloss Enamel 2.11 293 2.00 Total Dry Mils 5.50 02.F Interior Wood, 100% Acrylic Gloss DTM Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 319-8 COVENTRY Acrylic Enamel Undercoat 0.76 351 1.50 First 310-Series H 2 O RUS-KIL DTM Acrylic Enamel 1.09 295 2.00 Finish 310-Series H 2 O RUS-KIL DTM Acrylic Enamel 1.09 295 2.00 Total Dry Mils 5.50 Wood Finishing Specifications 9

02.G Interior Wood, Fire Retardant Finishing System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 319-8 COVENTRY Acrylic Enamel Undercoat 0.76 351 1.50 First 9835-239 FIRECOAT 320 0.80 145 4.00 Second 9835-239 FIRECOAT 320 0.80 145 4.00 Finish with any of the above-listed topcoats Consult your BLP Mobile Paints service representative for details. Total Dry Mils 9.50 02.H Interior Wood, Latex Flat System, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 219-8 SMOOTH-COTE Enamel Undercoat 0.79 347 1.50 First 289-line SMOOTH-COTE Interior Latex Flat 0.89 346 1.50 Finish 289-line SMOOTH-COTE Interior Latex Flat 0.89 346 1.50 Total Dry Mils 4.50 02.I Interior Wood, Latex Semi-gloss System, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 219-8 SMOOTH-COTE Enamel Undercoat 0.79 347 1.50 First 290-line SMOOTH-COTE Int. Latex Semi-gloss 1.60 252 1.50 Finish 290-line SMOOTH-COTE Int. Latex Semi-gloss 1.60 252 1.50 Total Dry Mils 4.50 02.J Interior Wood, Latex Eggshell System, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 219-8 SMOOTH-COTE Enamel Undercoat 0.79 347 1.50 First 292-line SMOOTH-COTE Int. Latex Eggshell 0.85 395 1.50 Finish 292-line SMOOTH-COTE Int. Latex Eggshell 0.85 395 1.50 Total Dry Mils 4.50 Wood Finishing Specifications 10

02.K Interior Wood, Alkyd Semi-Gloss Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 19-8 COVENTRY Alkyd Enamel Undercoat 3.35 387 2.00 First 135-Series COVENTRY Lustarite Satin-Gloss 3.04 427 2.00 Finish 135-Series COVENTRY Lustarite Satin-Gloss 3.04 427 2.00 Total Dry Mils 6.00 02.L Interior Wood, Alkyd Gloss Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 19-8 COVENTRY Alkyd Enamel Undercoat 3.35 3.87 2.00 First 30-Series NAM-A-LAC Gloss Enamel 3.18 409 1.50 Finish 30-Series NAM-A-LAC Gloss Enamel 3.18 409 1.50 Total Dry Mils 5.00 02.M Interior Wood, Alkyd Gloss Enamel System, Residential, Commercial & Light Industrial Service Coat Product Premium Industrial Quality VOC Sq.Ft. Mils Prime 19-8 COVENTRY Alkyd Enamel Undercoat 3.35 387 2.00 First 10-Series RUS-KIL Alkyd Gloss Enamel 3.35 385 2.00 Finish 10-Series RUS-KIL Alkyd Gloss Enamel 3.35 385 2.00 Total Dry Mils 6.00 02.N Interior Wood, Amide High Solids Epoxy Semi-gloss System,Residential, Com. & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime* 613-Series MOPOXY TM HS Semi-gloss Epoxy 2.00 374 3.00 First 613-Series MOPOXY TM HS Semi-gloss Epoxy 2.00 374 3.00 Finish 613-Series MOPOXY TM HS Semi-gloss Epoxy 2.00 374 3.00 *Thin first coat 20% with MOPOXY TM Brushing Thinner 75-35 Total Dry Mils 9.00 Wood Finishing Specifications 11

02.O Interior Wood, Amide High Solids Epoxy High-Gloss System, Residential, Com. & Light Industrial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime* 513-Series MOPOXY TM High Gloss Epoxy 4.30 314 2.00 First 513-Series MOPOXY TM High Gloss Epoxy 4.30 314 2.00 Finish 513-Series MOPOXY TM High Gloss Epoxy 4.30 314 2.00 *Thin first coat 20% with MOPOXY Brushing Thinner 75-35 02.P Interior Wood, Waterborne Acrylic Epoxy High Gloss System Total Dry Mils 6.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime* 69-AW-5 MOPOXY TM H 2 O-100 White 1.71 313 2.00 First 69-AW-5 MOPOXY TM H 2 O-100 White 1.71 313 2.00 Finish 69-AW-5 MOPOXY TM H 2 O-100 White 1.71 313 2.00 *Thin first coat 20% with Water 02.Q Interior Wood, Waterborne Amide Epoxy Semi-Gloss System Total Dry Mils 6.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime* 69-AW-6 MOPOXY TM H 2 O-200 White 1.00 225 2.00 First 69-AW-6 MOPOXY TM H 2 O-200 White 1.00 225 2.00 Finish 69-AW-6 MOPOXY TM H 2 O-200 White 1.00 225 2.00 *Thin first coat 20% with Water 02.R Interior Wood, White or Tinted Gloss Lacquer System Total Dry Mils 6.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime 9835-172 Lacquer Sanding Sealer Hi-Build White First 9835-line Lacquer Tint Base 345 1.00 Second 9835-line Lacquer Tint Base 345 1.00 Third 9835-line Lacquer Tint Base 345 1.00 Total Dry Mils 3.00 Wood Finishing Specifications 12

02.S Interior Wood, Alkyd Semi-gloss System, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 219-8 SMOOTH-COTE Enamel Undercoat 0.79 347 1.50 First 293-line SMOOTH-COTE Int Alkyd Semi-gloss 2.85 449 2.00 Finish 293-line SMOOTH-COTE Int Alkyd Semi-gloss 2.85 449 2.00 Total Dry Mils 5.50 03 EXTERIOR WOOD FINISHES, NATURAL GRAIN 03.A Exterior Wood, Natural Finish, Oil-based Sealer & Preservative, Residential & Commercial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 7-10 WEATHER-PROTECTOR Sealer 4.61 150 0.50 Finish 7-10 WEATHER-PROTECTOR Sealer 4.61 150 0.50 Penetrating finish, film thickness cannot be accurately measured Total Dry Mils 1.00 03.B Exterior Wood, Natural Finish, Clear Waterproofer (Paintable), Residential & Commercial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 74-7 WEATHER-TITE Clear Waterproofing 5.30 150 0.50 Finish 74-7 WEATHER-TITE Clear Waterproofing 5.30 150 0.50 Penetrating finish, film thickness cannot be accurately measured Total Dry Mils 1.00 Wood Finishing Specifications 13

03.C Exterior Wood, Natural Finish, Waterborne Clear Waterproofer (Paintable), Residential & Commercial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 74-17 H 2 O WEATHER-TITE Clear 0.68 150 0.50 Finish 74-17 H 2 O WEATHER-TITE Clear 0.68 150 0.50 Penetrating finish, film thickness cannot be accurately measured Total Dry Mils 1.00 03.D Exterior Wood, Natural Finish, Acrylic Wood Stain,Residential & Commercial Service Coat Product Premium Quality VOC Sq.Ft. Mils Prime 44-Line WEATHER PROTECTOR Acrylic Stain 1.77 275 1.50 Finish 44-Line WEATHER PROTECTOR Acrylic Stain 1.77 275 1.50 03.E Exterior Wood, 100% Phenolic Marine Spar Varnish Total Dry Mils 3.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime 470-31 JACK TAR 100% Phenolic Spar Varnish 3.79 657 1.00 First 470-31 JACK TAR 100% Phenolic Spar Varnish 3.79 657 1.00 Finish 470-31 JACK TAR 100% Phenolic Spar Varnish 3.79 657 1.00 03.F Exterior Wood, Marine Spar Varnish with Ultraviolet Filter Total Dry Mils 3.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime 470-34 JACK TAR Spar Varnish, UV Filter 3.82 657 1.00 First 470-34 JACK TAR Spar Varnish, UV Filter 3.82 657 1.00 Finish 470-34 JACK TAR Spar Varnish, UV Filter 3.82 657 1.00 Total Dry Mils 3.00 Wood Finishing Specifications 14

04 EXTERIOR WOOD, PAINTED FINISH 04.A Exterior Wood, Southernized Oil-Based Gloss House Paint Coat Product Premium Quality VOC Sq.Ft. Mils Prime 5-6 WEATHER-TITE Oil Base Primer 2.93 440 2.00 First 5-Series WEATHER-TITE Oil Base House Paint 1.28 645 2.00 Finish 5-Series WEATHER-TITE Oil Base House Paint 1.28 645 2.00 04.B Exterior Wood, 100% Acrylic Flat Finish House Paint Total Dry Mils 6.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime 6-6 WEATHER-TITE 100% Acrylic Primer 1.17 393 2.00 First 40-Series WEATHER-TITE 100% Acrylic Flat 1.03 291 2.00 Finish 40-Series WEATHER-TITE 100% Acrylic Flat 1.03 291 2.00 04.C Exterior Wood, 100% Acrylic Gloss Finish House Paint Total Dry Mils 6.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime 6-6 WEATHER-TITE 100% Acrylic Primer 1.17 393 2.00 First 140-Series WEATHER-TITE 100% Acrylic Gloss 1.99 296 2.00 Finish 140-Series WEATHER-TITE 100% Acrylic Gloss 1.99 296 2.00 04.D Exterior Wood, 100% Acrylic Satin Finish House Paint Total Dry Mils 6.00 Coat Product Premium Quality VOC Sq.Ft. Mils Prime 6-6 WEATHER-TITE 100% Acrylic Primer 1.17 393 2.00 First 240-Series WEATHER-TITE 100% Acrylic Satin 2.19 271 2.00 Finish 240-Series WEATHER-TITE 100% Acrylic Satin 2.19 271 2.00 Total Dry Mils 6.00 Wood Finishing Specifications 15

04.E Exterior Wood, Silicone Alkyd Yacht Finish, High Gloss Coat Product Premium Marine Quality VOC Sq.Ft. Mils Prime* 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.50 First 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.50 Finish 432-Series JACK TAR Silicone Yacht Finish 3.57 484 1.50 * Thin 10% with MOPAXOL Thinner 75-1 Total Dry Mils 4.50 04.F Exterior Wood, Acrylic Flat Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 206-10 SMOOTH-COTE 100% Acrylic Primer 1.48 387 1.50 First 291-line SMOOTH-COTE Vinyl Acrylic Flat 1.30 290 1.50 Finish 291-line SMOOTH-COTE Vinyl Acrylic Flat 1.30 290 1.50 Total Dry Mils 4.50 04.G Exterior Wood, Acrylic Gloss Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 206-10 SMOOTH-COTE 100% Acrylic Primer 1.48 387 1.50 First 294-line SMOOTH-COTE 100% Acrylic Gloss 1.48 377 1.50 Finish 294-line SMOOTH-COTE 100% Acrylic Gloss 1.48 377 1.50 Total Dry Mils 4.50 04.H Exterior Wood, Acrylic Semi-gloss Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 206-10 SMOOTH-COTE 100% Acrylic Primer 1.48 387 1.50 First 295-line SMOOTH-COTE 100% Acrylic Semi-gloss 1.54 335 1.50 Finish 295-line SMOOTH-COTE 100% Acrylic Semi-gloss 1.54 335 1.50 Total Dry Mils 4.50 Wood Finishing Specifications 16

04.I Exterior Wood, Acrylic Flat Finish, Residential, Commercial & Light Industrial Service Coat Product Professional Quality VOC Sq.Ft. Mils Prime 206-10 SMOOTH-COTE 100% Acrylic Primer 1.48 387 1.50 First 296-line SMOOTH-COTE 100% Acrylic Flat 1.25 283 1.50 Finish 296-line SMOOTH-COTE 100% Acrylic Flat 1.25 283 1.50 Total Dry Mils 4.50 Wood Finishing Specifications 17

RECOMMENDED FINISHING SPECIFICATIONS FOR FLOORS AND DECKS Beautiful floors are the focal point of any room or area. A gleaming floor is the joy of any homemaker and the hallmark of an efficient and well run commercial or industrial establishment. Decks, terraces, walks and piers enhance the exterior beauty of homes, hotels, marinas and other areas. This section includes a full range of floor finishing systems for residential, commercial, light industrial and heavy industrial applications, both interior and exterior, and is divided as follows: SURFACE PREPARATION RECOMMENDED PRODUCTS 01 INTERIOR WOODEN FLOORS 02 INTERIOR CONCRETE FLOORS 03 INTERIOR STEEL DECKING 04 EXTERIOR WOOD DECKS 05 EXTERIOR CONCRETE DECKS 06 EXTERIOR STEEL DECKS A comprehensive index will be found on the next page Please consult your BLP Mobile Paints representative for specific recommendations. Floor & Deck Finishing Specifications 1

SURFACE PREPARATION INTERIOR WOODEN FLOORS New wooden floors should be inspected carefully prior to finishing. Nail holes should be filled and the floor sanded with fine sandpaper to a smooth finish. All dust must be removed. Good ventilation is essential. Never paint or varnish on days of high humidity or rain. Follow instructions exactly for a finish of which to be proud. GOOD VENTILATION IS ESSENTIAL TO ASSURE PROPER EVAPORATION OF SOLVENTS AND PREVENT DANGEROUS ACCUMULATIONS OF FUMES. CONCRETE FLOORS Moisture damage is the major cause of paint failure as well as the lifting of other types of flooring laid over concrete floors at or below grade level. A moisture barrier installed prior to construction will prevent the percolation of moisture through the slab. Omission of this moisture barrier is almost impossible to correct and seriously limits the selection and durability of the finish. Bare concrete should always be etched with muriatic acid and rinsed with clear water to remove the laitance which is a natural result of trowelling and to leave the surface porous and receptive to paint. The surface must be clean, dry and dust free. Previously sealed concrete presents a series of problems beginning with the correct identification of the sealer used and whether it can be removed to allow the adhesion of paint. Please check with your BLP Mobile Paint representative for specific recommendations. STEEL DECKING Surface preparation is covered in Ferrous Metals in this book. Solvent clean steel iaw SSPC-SP 1 to remove grease and oil. Near-White Blast Cleaning iaw SSPC-SP 10 is recommended; Commercial Blast iaw SSPC- SP 6 should be considered minimum acceptable preparation for marine environments. If abrasive cleaning is not possible because of mechanical or environmental considerations, Power Tool Clean iaw SSPC-SP 3 and treat as in the section on Maintenance Upgrade Systems under Ferrous Metals. Floor & Deck Finishing Specifications 2

RECOMMENDED PRODUCTS All products are lead-free, chromate-free, mercury-free and VOC-compliant. NUWOOD Penetrating Wood Finish, 71-Series, is a polyurethane stain or wood finish. NUWOOD Polyurethane Varnish - Very pale, durable, with excellent resistance to abrasion, hot and cold water, acid, alkali, grease, alcohol and soil. Recommended for homes, public buildings, institutions, schools and gymnasiums. Available in Gloss, 72-35, and Satin, 72-36. FLO-TEC Phenolic HD Gym Floor Finish - Low viscosity wood finish which penetrates into the pores of the wood, sealing the surface and hardening the wood fibers to a considerable depth. Leaves no varnish film on the surface. Highly recommended for gymnasium floors as well as other residential and institutional uses. WEATHER-TITE Waterproofing Sealer, Clear, 74-7 -clear waterproofing which penetrates and repels water, protecting against rot and mildew. Does not change color or appearance of wood. Easy to apply. Contains no silicones, may be painted after 24 hours. WEATHER-TITE H 2 O Waterproofing Clear, 74-17 - a clear, waterborne, paintable waterproofing sealer for masonry, wood, canvas and fabric. Contains no silicones. Low odor. DUB-L-TITE TM Silicone Waterproofing, Clear, 74-12 - a clear silicone waterproofing for masonry surfaces. Penetrates and repels water while allowing the surface to breathe. Forms no film and does not change color. Easy to apply.. WEATHER-TITE H 2 O Dub-L-Tite Clear Waterproofing, 74-13 - a clear waterborne silicone/silane sealer for exterior masonry surfaces. Forms no film and will not change the appearance of the surface. H 2 O Concrete Stain, 308-Series - a waterborne polyurethane acrylic stain with good color and gloss retention and excellent abrasion resistance.. SPEEDECK Polyurethane Floor & Deck Enamel - a polyurethane modified alkyd enamel - Excellent protection against abrasion and weather in mild industrial and marine environments. Good color and gloss retention. Available in stock colors as seen on the color card and in a wide range of custom colors. Floor & Deck Finishing Specifications 3

H 2 O Acrylic Floor & Patio Satin Finish, 350-Series - Waterborne polyurethane modified acrylic enamel for interior and exterior service. Good color and gloss retention, excellent abrasion resistance. Available in stock colors as seen on the color card and in a wide range of custom colors. JACK TAR Silicone Yacht Finish, 432 Line - Silicone Alkyd Enamel - All of the advantages and color range of alkyd enamels plus outstanding gloss and color retention under ultraviolet. Unsurpassed for residential, commercial, institutional, industrial and marine use. MOPOXY TM - our brand name for our complete line of catalyzed epoxies. Extremely durable, excellent chemical and abrasion resistance. Recommended for residential, institutional, commercial and industrial service. MOTHANE - our brand name for our line of catalyzed polyurethane. Extremely durable, excellent chemical and abrasion resistance. Outstanding gloss and color retention. Recommended for residential, institutional, commercial and industrial service. MOPOXY TM H 2 O-200 Waterborne Amide Epoxy - very good abrasion, moisture and chemical resistance. Low odor. Semi-gloss finish. Very low VOC MOPOXY TM HS High Solids Epoxy - a high-solids amide cured epoxy with excellent chemical, moisture and abrasion resistance. MOPOXY-PLUS TM is a high solids, high build, surface tolerant epoxy with excellent abrasion, moisture and chemical resistance. MOPOXY TM PRE-PREP Sealer, Clear, 41-AF-2, is a two component, 0 VOC, 100% solids epoxy which is almost water-thin with exceptional penetration properties. MOPOXY PRE-PREP requires 48 hours at 75 F for full cure. Allow to dry overnight and apply finish coat while the prime coat is still slightly tacky. If a clear sealer is desired, apply a second coat of MOPOXY PRE-PREP as a finish coat. MOPOXY TM AR-100 Deck Armor, 41-BW-1, is a 100% solids, 0 VOC, high performance deck coating with excellent resistance to moisture, abrasion and mechanical damage and good resistance to most solvents and chemicals. Apply by airless spray at the rate of 26 square feet per gallon to produce a dry film thickness of 60 mils. MOPOXY TM NS-200 Non-Skid Deck Armor, 41-BW-12, is a 94.9% solids, very low VOC, high performance deck coating with excellent resistance to moisture, abrasion and mechanical damage and good resistance to most solvents and chemicals. Apply by brush, roller of trowel at the rate of 24 square feet per gallon to produce a dry film thickness of 60 mils. Floor & Deck Finishing Specifications 4

INTERIOR FLOOR FINISHING SYSTEMS 01 WOOD FLOORS, INTERIOR, RESIDENTIAL & COMMERCIAL SERVICE 01.A Interior Wood Floors, Natural, Gloss Polyurethane Varnish System Coat Product Residential & Commercial Service VOC Sq.Ft. Mils Prime 71-Series NUWOOD Penetrating Wood Stain 4.61 750 N/A First 72-35 NUWOOD Polyurethane Gloss Finish 3.77 673 1 Finish 72-35 NUWOOD Polyurethane Gloss Finish 3.77 673 1 Total Dry Mils 2.0 01.B Interior Wood Floors, Natural, Satin-Gloss Polyurethane Varnish System Coat Product Residential & Commercial Service VOC Sq.Ft. Mils Prime 71-Series NUWOOD Penetrating Wood Stain 4.61 750 N/A First 72-36 NUWOOD Polyurethane Satin Finish 3.77 673 1 Finish 72-36 NUWOOD Polyurethane Satin Finish 3.77 673 1 Total Dry Mils 2.0 01.C Interior Wood Floors, Natural, Phenolic Gym Floor Finish Coat Product Commercial & Institutional Service VOC Sq.Ft. Mils Prime 70-41 FLO-TEC Phenolic HD Gym Floor Finish 4.45 500 1 First 70-41 FLO-TEC Phenolic HD Gym Floor Finish 4.45 500 1 Finish 70-41 FLO-TEC Phenolic HD Gym Floor Finish 4.45 500 1 Total Dry Mils 3.0 01.D Interior Wood Floors, Waterborne Polyurethane Acrylic Satin Enamel Finish Coat Product Residential & Light Commercial Service VOC Sq.Ft. Mils Prime 6-06 WEATHER-TITE Acrylic Universal Primer 1.17 393 1.5 First 350-Series H 2 O Acrylic Floor & Patio Finish 2.00 305 2 Finish 350-Series H 2 O Acrylic Floor & Patio Finish 2.00 305 2 Total Dry Mils 5.5 Floor & Deck Finishing Specifications 5

01.E Interior Wood Floors, Polyurethane Gloss Enamel Finish Coat Product Residential & Light Commercial Service VOC Sq.Ft. Mils Prime* 50-Series SPEEDECK Polyurethane Enamel 3.35 388 2 Finish 50-Series SPEEDECK Polyurethane Enamel 3.35 388 2 *Thin 10% with MoPaxOl Thinner 75-1 on new wood Total Dry Mils 4.0 01.F Interior Wood Floors, Waterborne Amide Epoxy Semi-gloss Finish Coat Product Commercial & Light Industrial Service VOC Sq.Ft. Mils Prime* 69-AW-6 MOPOXY TM H2O-200 Epoxy Coating. 1.00 225 3 Finish 69-AW-6 MOPOXY TM H2O-200 Epoxy Coating. 1.00 225 3 *Thin 20% with MOPOXY TM H2O Thinner 43-EF-89 on new wood Total Dry Mils 6.0 01.G Interior Wood Floors, Catalyzed Polyamide Epoxy Semi-gloss Finish Coat Product Commercial & Light Industrial Service VOC Sq.Ft. Mils Prime* 613-Series MOPOXY TM HS High Solids Epoxy Coating. 2.10 374 3 Finish 613-Series MOPOXY TM HS High Solids Epoxy Coating. 2.10 374 3 *Thin 10% with MOPOXY TM Brushing Thinner 75-35 on new wood Total Dry Mils 6.0 01.H Interior Wood Floors, Catalyzed Polyamide Epoxy High-gloss Finish Coat Product Commercial & Light Industrial Service VOC Sq.Ft. Mils Prime* 513-Series MOPOXY TM High Gloss Epoxy Coating. 5.14 314 2 Finish 513-Series MOPOXY TM High Gloss Epoxy Coating. 5.14 314 2 *Thin 10% with MOPOXY TM Brushing Thinner 75-35 on new wood Total Dry Mils 4.0 Floor & Deck Finishing Specifications 6

02 C0NCRETE FLOORS, INTERIOR, RESIDENTIAL, COMMERCIAL & INDUSTRIAL 02.A Interior Concrete Floors, Waterborne Polyurethane Acrylic Satin Finish Coat Product Residential & Light Commercial Service VOC Sq.Ft. Mils Prime 308-Series H 2 O Concrete Stain, Satin Gloss 2.00 374 1.5 Finish 308-Series H 2 O Concrete Stain, Satin Gloss 2.00 374 1.5 Total Dry Mils 3.0 02.B Interior Concrete Floors, Waterborne Polyurethane Acrylic Enamel Satin Finish Coat Product Residential & Light Commercial Service VOC Sq.Ft. Mils Prime 350-Series H 2 O Acrylic Floor & Patio Satin Finish 2.00 305 2 Finish 350-Series H 2 O Acrylic Floor & Patio Satin Finish 2.00 305 2 Total Dry Mils 4.0 02.C Interior Concrete Floors, Polyurethane Enamel Gloss Finish Coat Product Residential & Light Commercial Service VOC Sq.Ft. Mils Prime* 50-Series SPEEDECK Polyurethane Enamel 3.35 388 2 Finish 50-Series SPEEDECK Polyurethane Enamel 3.35 388 2 *Thin 10% with MoPaxOl Thinner 75-1 on new concrete Total Dry Mils 4.0 02.D Interior Concrete Floors, Waterborne Catalyzed Epoxy System, Semi-Gloss Finish Coat Product Commercial & Industrial Service VOC Sq.Ft. Mils Prime* 69-AW-6 MOPOXY H 2 O-200 Amide Epoxy 1.00 225 3 First 69-AW-6 MOPOXY H 2 O-200 Amide Epoxy 1.00 225 3 Second 69-AW-6 MOPOXY H 2 O-200 Amide Epoxy 1.00 225 3 *May be thinned slightly with water to improve penetration on new concrete Total Dry Mils 9.0 Floor & Deck Finishing Specifications 7

02.E Interior Concrete Floors, High-Solids Catalyzed Epoxy System, Semi-Gloss Finish Coat Product Commercial & Industrial Service VOC Sq.Ft. Mils Prime* First 613-Series 613-Series MOPOXY HS High Solids Epoxy MOPOXY HS High Solids Epoxy 2.10 2.10 374 374 3 3 Finish 613-Series MOPOXY HS High Solids Epoxy 2.10 374 3 * Thin 20% with MOPOXY Brushing Thinner, 75-35 on new concrete Total Dry Mils 9.0 02.F Interior Concrete Floors, Catalyzed Epoxy System, High-Gloss Finish Coat Product Commercial & Industrial Service VOC Sq.Ft. Mils Prime* 513-Series MOPOXY High Gloss Epoxy Coating. 5.14 314 2 First 513-Series MOPOXY High Gloss Epoxy Coating. 5.14 314 2 Finish 513-Series MOPOXY High Gloss Epoxy Coating. 5.14 314 2 * Thin 20% with MOPOXY Brushing Thinner, 75-35 on new concrete Total Dry Mils 6.0 02.G Interior Concrete Floors, High Build Epoxy System, Semi-Gloss Finish Coat Product Heavy Industrial Service VOC Sq.Ft. Mils Prime 41-AF-2 MOPOXY-PREP Epoxy Sealer 0.00 1069 1.5 First Second 41-CW-1 613-Series MOPOXY-PLUS HB HS Epoxy MOPOXY HS High Solids Epoxy 2.36 2.10 131 374 8 3 Finish* 613-Series MOPOXY HS High Solids Epoxy 2.10 374 3 *Add JACK TAR Non-Skid, 492-03, for anti-skid properties Total Dry Mils 15.5 02.H Interior Concrete Floors, 100% Solids Epoxy Finish Coat Product Heavy Industrial Service VOC Sq.Ft. Mils Prime 41-AF-2 MOPOXY-PREP Epoxy Sealer 0.00 1069 1.5 Finish 41-BW-1* MOPOXY AR-100 Deck Armor 0.00 26 60 *Apply by airless spray or trowel Total Dry Mils 61.5 Floor & Deck Finishing Specifications 8

02.I Interior Concrete Floors, High Solids Non-Skid Epoxy Finish Coat Product Heavy Industrial Service VOC Sq.Ft. Mils Prime** 41-AF-2 MOPOXY-PREP Epoxy Sealer 0.00 1069 1.5 Finish 41-BW-12* MOPOXY NS-200 Non-Skid Deck Armor 0.75 24 60 *Apply by brush, roller or trowel ** Alternate Primer: MOPOXY HS Epoxy 613-line Total Dry Mils 61.5 03 STEEL DECKING, INTERIOR, RESIDENTIAL, COMMERCIAL & INDUSTRIAL SERVICE 03.A Interior Steel Decking, Polyurethane Gloss Enamel Finish Coat Product Residential & Light Commercial Service VOC Sq.Ft. Mils Prime 10-10 RUS-KIL Metal Primer, Red 3.35 395 2 First 50-Series SPEEDECK Polyurethane Enamel 3.35 388 1.5 Finish 50-Series SPEEDECK Polyurethane Enamel 3.35 388 1.5 Total Dry Mils 5.0 03.B Interior Steel Decking, Waterborne Catalyzed Epoxy System, Semi-Gloss Finish Coat Product Commercial & Light Industrial Service VOC Sq.Ft. Mils Prime 69-DR-1 MOPOXY H 2 O-200 Metal Primer 0.89 257 3 First 69-AW-6 MOPOXY H 2 O-200 Amide Epoxy 1.00 225 3 Finish* 69-AW-6 MOPOXY H 2 O-200 Amide Epoxy 1.00 225 3 * Add JACK TAR Non-Skid 492-3 to finish coat for anti-skid properties Total Dry Mils 9.0 03.C Interior Steel Decking, High-Solids Catalyzed Epoxy System, Semi-Gloss Finish Coat Product Commercial & Industrial Service VOC Sq.Ft. Mils Prime 613-10 MOPOXY HS High Solids Epoxy Primer 2.00 382 3 First Finish* 613-Series 613-Series MOPOXY HS High Solids Epoxy MOPOXY HS High Solids Epoxy 2.10 2.10 374 374 3 3 * Add JACK TAR Non-Skid 492-3 to finish coat for anti-skid properties Total Dry Mils 9.0 Floor & Deck Finishing Specifications 9

03.D Interior Steel Decking, Catalyzed Epoxy System, High-Gloss Finish Coat Product Commercial & Industrial Service VOC Sq.Ft. Mils Prime 513-10 MOPOXY Epoxy Primer 4.24 322 2 First Finish* 513-Series 513-Series MOPOXY High Gloss Epoxy Coating. MOPOXY High Gloss Epoxy Coating. 5.14 5.14 314 314 2 2 * Add JACK TAR Non-Skid 492-3 to finish coat for anti-skid properties Total Dry Mils 6.0 03.E Interior Steel Decks, High Build Epoxy System, Semi-Gloss Finish Coat Product Commercial, Industrial & Marine Service VOC Sq.Ft. Mils Prime First 613-10 41-CW-1 MOPOXY HS High Solids Epoxy Primer MOPOXY-PLUS HB HS Epoxy 2.00 2.36 382 131 3 8 Second 613-Series MOPOXY HS High Solids Epoxy 2.10 374 3 Finish* 613-Series MOPOXY HS High Solids Epoxy 2.10 374 3 * Add JACK TAR Non-Skid 492-03 to finish coat for anti-skid properties Total Dry Mils 17.0 03.F Interior Steel Decking, 100% Solids Epoxy Finish Coat Product Heavy Industrial & Marine Service VOC Sq.Ft. Mils Prime 613-10 MOPOXY HS High Solids Epoxy Primer 2.00 382 3 Finish 41-BW-1* MOPOXY AR-100 Deck Armor 0.00 26 60 *Apply by airless spray or trowel Total Dry Mils 63.0 03.G Interior Steel Decking, High Solids Non-Skid Epoxy Finish Coat Product Heavy Industrial & Marine Service VOC Sq.Ft. Mils Prime 613-10 MOPOXY HS High Solids Epoxy Primer 2.00 382 3 Finish 41-BW-12* MOPOXY NS-200 Non-Skid Deck Armor 0.75 24 60 *Apply by brush, roller or trowel Total Dry Mils 63.0 Mobile Paints has a wide selection of specialized epoxies. We invite your inquiry. Floor & Deck Finishing Specifications 10

EXTERIOR FLOOR & DECK FINISHING SYSTEMS 04 WOOD DECKS, EXTERIOR - RESIDENTIAL, COMMERCIAL, MARINE SERVICE 04.A Exterior Wooden Decks, Clear Waterborne Waterproofing, Natural Finish Coat Product Premium Quality VOC Sq.Ft. Mils Prime 74-17 H 2 O WEATHER-TITE Clear Waterproofing 0.68 100 N/A Finish 74-17 H 2 O WEATHER-TITE Clear Waterproofing 0.68 100 N/A Total Dry Mils 0.0 04.B Exterior Wooden Decks, Clear Waterproofing, Natural Finish Coat Product Premium Quality VOC Sq.Ft. Mils Prime 74-7 WEATHER-TITE Clear Waterproofing 6.14 100 N/A Finish 74-7 WEATHER-TITE Clear Waterproofing 6.14 100 N/A Total Dry Mils 0.0 04.C Exterior Wood Decks, Waterborne Polyurethane Enamel, Satin Gloss Finish Coat Product Residential & Light Commercial Service VOC Sq.Ft. Mils Prime 6-6 WEATHER-TITE Acrylic Universal Primer 1.17 393 1.5 Finish 350-Series H 2 O Acrylic Floor & Patio Satin Finish 2.00 305 2 Second 350-Series H 2 O Acrylic Floor & Patio Satin Finish 2.00 305 2 Total Dry Mils 5.5 04.D Exterior Wood Decks, Polyurethane Enamel, Gloss Finish Coat Product Residential & Light Commercial Service VOC Sq.Ft. Mils Prime* 50-Series SPEEDECK Polyurethane Enamel 3.35 388 1.5 First 50-Series SPEEDECK Polyurethane Enamel 3.35 388 1.5 Finish 50-Series SPEEDECK Polyurethane Enamel 3.35 388 1.5 *Thin 10% with MoPaxOl Thinner 75-1 on new wood Total Dry Mils 4.5 Floor & Deck Finishing Specifications 11

04.E Exterior Wood Decks, Silicone Alkyd Enamel, Gloss Finish Coat Product Residential, COMMERCIAL & Marine Service VOC Sq.Ft. Mils Prime* 432-Line JACK TAR Silicone Yacht Finish 3.57 484 1.5 Second 432-Line JACK TAR Silicone Yacht Finish 3.57 484 1.5 Finish 432-Line JACK TAR Silicone Yacht Finish 3.57 484 1.5 *Thin 10% with MoPaxOl Thinner 75-1 on new wood Total Dry Mils 4.5 05 CONCRETE FLOORS & DECKS, EXTERIOR FINISHING SYSTEMS 05.A Exterior Concrete Decks, Clear Waterborne Silicone Waterproofing, Natural Finish Coat Product Residential, Commercial & Marine Service VOC Sq.Ft. Mils Prime 74-13 WEATHER-TITE H 2 O Dub-L-Tite Clear 0.00 100 N/A Finish 74-13 WEATHER-TITE H 2 O Dub-L-Tite Clear 0.00 100 N/A Total Dry Mils 0.0 05.B Exterior Concrete Decks, Clear Silicone Waterproofing, Natural Finish Coat Product Premium Quality VOC Sq.Ft. Mils Prime 74-12 DUB-L-TITE Clear Waterproofing 6.19 100 N/A Finish 74-12 DUB-L-TITE Clear Waterproofing 6.19 100 N/A Total Dry Mils 0.0 05.C Exterior Concrete Decks, Waterborne Polyurethane Acrylic Stain, Satin Finish Coat Product Residential, Commercial & Marine Service VOC Sq.Ft. Mils Prime 308-Series H 2 O Concrete Stain 2.00 374 1.5 First 308-Series H 2 O Concrete Stain 2.00 374 1.5 Finish 308-Series H 2 O Concrete Stain 2.00 374 1.5 Total Dry Mils 4.5 Floor & Deck Finishing Specifications 12

05.D Exterior Concrete Decks, Waterborne Polyurethane Acrylic Enamel, Satin Gloss Finish Coat Product Residential, Commercial & Marine Service VOC Sq.Ft. Mils Prime 350-Series H 2 O Acrylic Floor & Patio Satin Finish 2.00 305 2 First 350-Series H 2 O Acrylic Floor & Patio Satin Finish 2.00 305 2 Finish 350-Series H 2 O Acrylic Floor & Patio Satin Finish 2.00 305 2 Total Dry Mils 6.0 05.E Exterior Concrete Decks, Polyurethane Enamel, Gloss Finish, Residential, Commercial & Marine Service Coat Product Residential & Light Commercial Service VOC Sq.Ft. Mils Prime* 50-Series SPEEDECK Polyurethane Enamel 3.35 388 1.5 First 50-Series SPEEDECK Polyurethane Enamel 3.35 388 1.5 Finish 50-Series SPEEDECK Polyurethane Enamel 3.35 388 1.5 *Thin 10% with MoPaxOl Thinner 75-1 on new concrete Total Dry Mils 4.5 05.F Exterior Concrete Decks, Silicone Alkyd Enamel, Gloss Finish Coat Product Residential, Commercial & Marine Service VOC Sq.Ft. Mils Prime* 432-Line JACK TAR Silicone Yacht Finish 3.57 484 1.5 Second 432-Line JACK TAR Silicone Yacht Finish 3.57 484 1.5 Finish 432-Line JACK TAR Silicone Yacht Finish 3.57 484 1.5 *Thin 10% with MoPaxOl Thinner 75-1 on new concrete Total Dry Mils 4.5 Floor & Deck Finishing Specifications 13

06 STEEL DECKING, EXTERIOR, RESIDENTIAL, COMMERCIAL & INDUSTRIAL SERVICE 06.A Exterior Steel Decking, Polyurethane Gloss Enamel Finish Coat Product Residential & Light Commercial Service VOC Sq.Ft. Mils Prime 10-10 RUS-KIL Metal Primer, Red 3.35 395 2 First 50-Series SPEEDECK Polyurethane Enamel 3.35 388 1.5 Finish* 50-Series SPEEDECK Polyurethane Enamel 3.35 388 1.5 * Add JACK TAR Non-Skid 492-3 to finish coat for anti-skid properties Total Dry Mils 5.0 06.B Exterior Steel Decks, Silicone Alkyd Enamel, Gloss Finish Coat Product Residential, Commercial & Marine Service VOC Sq.Ft. Mils Prime 10-10 RUS-KIL Metal Primer, Red 3.35 395 2 First 432-Line JACK TAR Silicone Yacht Finish 3.57 484 1.5 Finish* 432-Line JACK TAR Silicone Yacht Finish 3.57 484 1.5 * Add JACK TAR Non-Skid 492-3 to finish coat for anti-skid properties Total Dry Mils 5.0 06.C Exterior Steel Decking, High-Solids Epoxy/Polyurethane System, High Gloss Finish Coat Product Industrial & Marine Service VOC Sq.Ft. Mils Prime 613-10 MOPOXY HS High Solids Epoxy Primer 2.00 382 3 First Second 613-Series 72-Series MOPOXY HS High Solids Epoxy MOTHANE HS-1000 Polyurethane 2.10 2.45 374 513 3 2 Finish* 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 * Add JACK TAR Non-Skid 492-3 to finish coat for anti-skid properties Total Dry Mils 10.0 Floor & Deck Finishing Specifications 14

06.D Exterior Steel Decks, High Build Epoxy/Polyurethane System, High Gloss Finish Coat Product Heavy Industrial & Marine Service VOC Sq.Ft. Mils Prime 613-10 MOPOXY HS High Solids Epoxy Primer 2.00 282 3 First Second 41-CW-1 72-Series MOPOXY-PLUS HB HS Epoxy MOTHANE HS-1000 Polyurethane 2.36 2.45 131 513 8 2 Finish* 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 * Add JACK TAR Non-Skid 492-3 to finish coat for anti-skid properties Total Dry Mils 15.0 06.E Exterior Steel Decking, 100% Solids Epoxy Finish Coat Product Heavy Industrial & Marine Service VOC Sq.Ft. Mils Prime 613-10 MOPOXY HS High Solids Epoxy Primer 2.00 282 3 Finish 41-BW-1* MOPOXY AR-100 Deck Armor 0.00 26 60 *Apply by airless spray or trowel Total Dry Mils 63.0 06.G Exterior Steel Decking, High Solids Non-Skid Epoxy Finish Coat Product Heavy Industrial & Marine Service VOC Sq.Ft. Mils Prime 613-10 MOPOXY HS High Solids Epoxy Primer 2.00 382 3 Finish 41-BW-12* MOPOXY NS-200 Non-Skid Deck Armor 0.75 24 60 *Apply by brush, roller or trowel Total Dry Mils 63.0 Mobile Paints has a wide selection of specialized epoxies. We invite your inquiry. Floor & Deck Finishing Specifications 15

RECOMMENDED PAINTING SPECIFICATIONS FOR WATER STORAGE TANKS This section covers interior finishes for water storage tanks for potable water, for fire protection water, raw process water and for de-mineralized or distilled water at ambient temperatures. Representative exterior coating systems are included but a more extensive listing will be found under Ferrous Metals in this same book. Originally written for new construction, the scope of Ferrous Metals has been expanded to include maintenance painting, both for recoating original systems and for upgrading coating systems The NSF is the recognized authority for potable water storage tanks. Recommended coatings approved by this organization also meet AWWA requirements for potable water and are suitable for direct food contact in food processing and pharmaceutical plants. The Society for Protective Coatings, formerly the Steel Structures Painting Council, is the recognized authority on surface preparation and painting procedures for steel. Reference is made to their standards as follows: Solvent Cleaning SSPC-SP 1 Hand Cleaning SSPC-SP 2 Power Tool Cleaning SSPC-SP 3 White Metal Blast SSPC-SP 5 Commercial Blast SSPC-SP 6 Brush-off Blast SSPC-SP 7 Near White Blast SSPC-SP 10 Power Tool Clean to Bare Metal SSPC-SP 11 Commercial sandblast iaw SSPC-SP 6 should be considered the minimum acceptable surface preparation for non-immersion service. White Metal Blast iaw SSPC-SP 5 is the minimum acceptable surface preparation for immersion service. Wet sandblasting is becoming more common to control dust and to comply with EPA requirements, requiring new techniques and the use of additives to the blasting water to prevent immediate rust bloom. Consult your BLP Mobile Paint representative for equipment and additive recommendations. Shop coats and primers for piping, pumps and non-critical areas should be selected to be compatible with the exterior finish system specified. After erection, all nuts, bolts, abraded areas and scratches should be cleaned and spot primed before additional coats of primer or finish are applied. Welds should be ground to remove weld splatter before priming. Positive ventilation is essential as a safety measure to prevent any accumulation of solvent vapors during both application and during the curing period. We recommend the use of an extractor 24 hours a day until cure is complete. Water Storage Tanks Systems 1

In temperate climates, we recommend a 7 to 14 day curing period. As catalyzed epoxies cure more rapidly in tropical climates, we have found that a 5 to 7 day curing period is acceptable if continuous forced ventilation is maintained. After curing is complete, rinse thoroughly with fresh water to remove any dust or residual solvent contamination, then seal and fill with water for service. POTABLE WATER TANKS All products recommended are approved by the NSF for lining potable water tanks and meet USDA and AWWA regulations. MoPoxY HS-50 Epoxy Coating is a high-build, high-solids, polyamide epoxy certified to ANSI/NSF Standard 61 for potable water tank lining. Best applied by airless spray, may be rolled or brushed. VOC compliant, lead, chromate and mercury free. Acceptable for use on direct food contact surfaces. Surface preparation: White Metal Blast iaw SSPC-SP 5 is minimum acceptable for immersion service. FIRE PROTECTION STORAGE TANKS & RAW PRODUCTION WATER TANKS Surface preparation: White Metal Blast iaw SSPC-SP 5 is minimum acceptable for immersion service. The following products are recommended for immersion service for non-potable water storage tanks. All offer excellent resistance to fresh and salt water immersion. MoPoxY TM PRIME Preconstruction Primer is a modified polyamide epoxy designed for use as a shop coat to protect cleaned steel against corrosion during fabrication and assembly. Also an excellent tie coat or zinc seal over inorganic zinc. Weldable, compatible with all below listed systems. MoPoxY TM HB High Build Epoxy Primer is a marine epoxy designed for ship-bottom service. High solids, VOC - compliant. Lead and mercury free. Best applied by airless spray, may be rolled or brushed. MoPoxY TM MASTIC is an amine adduct direct to metal (DTM) coating with excellent resistance to abrasion, salt and fresh water immersion. High-build, very high-solids, very low-voc. Lead, mercury and chromate free. Best applied by airless spray, may be rolled or brushed. MoPoxY TM -PLUS is a modified polyamine direct to metal (DTM) epoxy with excellent resistance to fresh and salt water immersion and abrasion. High build, high solids, low VOC. Lead, mercury and chromate free. Best applied by airless spray, may be rolled or brushed. MIL-P-24441/29, Formula 150, Type IV, is a green polyamide epoxy primer formulated for Naval use on bilges, underwater hulls and other surfaces subject to salt water immersion. Low VOC and lead free. MIL-P-24441, Formula 152, Type IV, White, is a hard, durable, chemical resistant, non porous polyamide epoxy suitable for use over Formula 150. Suitable for fresh and salt water immersion. Other color formulations are available. MoPoxY TM PHENOLIC Epoxy is a high performance heavy duty formulation with excellent chemical and abrasion resistance, suitable for fresh and salt water immersion. Also certifiable under 40 CFR 175.300 for direct food contact. Water Storage Tanks Systems 2

DE-MINERALIZED WATER TANKS De-mineralized water, distilled water, and de-ionized water are all highly reactive and require special coatings for containment. The below-listed products are recommended for ambient to slightly elevated temperatures; for high temperatures, consult your BLP Mobile Paint representative. Surface preparation: White Metal Blast iaw SSPC-SP 5 is minimum acceptable for immersion service. MoPoxY TM GF Glass Flake Phenolic Epoxy is a high performance heavy duty tank lining, reinforced with glass flake pigment, for maximum resistance to permeation by water and chemicals. This product has excellent abrasion, water and chemical resistance at elevated temperatures. High build, high solids, low VOC. Lead, mercury, and chromate free. Apply by airless spray only. MoPoxY TM MASTIC is an amine adduct direct to metal (DTM) coating with excellent resistance to abrasion, salt and fresh water immersion. High-build, very high-solids, very low-voc, lead, mercury and chromate free. Best applied by airless spray, may be rolled or brushed. MoPoxY TM -PLUS is a modified polyamine direct to metal (DTM) epoxy with excellent resistance to fresh and salt water immersion and abrasion. High build, high solids, low VOC. Lead, mercury and chromate free. Best applied by airless spray, may be rolled or brushed. Water Storage Tanks Systems 3

WATER STORAGE TANKS - INTERIOR COATING SYSTEMS 01 POTABLE WATER TANKS All products recommended are certified by the NSF for lining potable water tanks and meet ANSI/NSF Standard 61. 01.A Polyamide Epoxy System, 3.4 VOC Coat Product Premium Quality Epoxy VOC Sq Ft Mils Prime 40-BH-11 MoPoxY TM HS-50 NSF, Gray 3.40 134 6 Finish 40-BW-5 MoPoxY TM HS-50 NSF, White 3.40 134 6 Total Dry Mils 12.0 02 FIRE PROTECTION STORAGE TANKS & RAW PRODUCTION WATER TANKS 02.A Preconstruction Primer: for use as shop coat during fabrication and erection. Coat Product VOC Sq Ft Mils Shop 40-DR-12 MoPoxY TM PRIME, Red 5.25 348 1 Coat Compatible with all below systems Total Dry Mils 1.0 02.B Epoxy Primer/Epoxy Mastic Finish Coat Product VOC Sq Ft Mils Prime 40-DR-5 MoPoxY TM HB Hi-Build Primer, Red 3.49 131 6 Finish 40-AW-32 MoPoxY TM MASTIC, White 1.30 217 6 02.C Epoxy Mastic Primer & Finish Total Dry Mils 12.0 Coat Product VOC Sq Ft Mils Prime 40-AH-51 MoPoxY TM MASTIC, Dawn Gray 1.30 217 6 Finish 40-AW-32 MoPoxY TM MASTIC, White 1.30 217 6 Total Dry Mils 12.0 Water Storage Tanks Systems 4

02.D Epoxy High-Build, High-Solids Primer & Finish Coat Product VOC Sq Ft Mils Prime 41-CH-1 MoPoxY TM -PLUS, Haze Gray 2.36 131 8 Finish 41-CW-1 MoPoxY TM -PLUS, White 2.36 131 8 Total Dry Mils 16.0 02.E Navy Formulation MIL-P-24441Type IV Epoxy Primer and Finish Coat Product VOC Sq Ft Mils Prime 40-CM-7 MIL-P-24441/T IV /F 150 Primer Green 2.80 346 3 Finish 40-AW-42 MIL-P-24441/T IV /F 152 White 1.30 319 3 Total Dry Mils 6.0 02.F Phenolic Epoxy Primer and Finish, Maximum Protection Coat Product VOC Sq Ft Mils Prime 41-AH-1 MoPoxY TM PH Phenolic Epoxy, Gray 2.81 156 6 Intermediate 41-AH-1 MoPoxY TM PH Phenolic Epoxy, Gray 2.81 156 6 Finish 41-AH-1 MoPoxY TM PH Phenolic Epoxy, Gray 2.81 156 6 Apply by airless spray only Total Dry Mils 18.0 03 DE-MINERALIZED WATER TANKS 03.A Glass Flake Phenolic Epoxy Primer & Finish, Maximum Protection Coat Product VOC Sq Ft Mils Prime 41-AH-2 MoPoxY TM GF Glass Flake Phenolic, Gray 2.65 122 8 Intermediate 41-AH-2 MoPoxY TM GF Glass Flake Phenolic, Gray 2.65 122 8 Finish 41-AH-2 MoPoxY TM GF Glass Flake Phenolic, Gray 2.65 122 8 Apply by airless spray only Total Dry Mils 24.0 Water Storage Tanks Systems 5

03.B Epoxy Mastic Primer & Finish Coat Product VOC Sq Ft Mils Prime 40-AH-51 MoPoxY TM MASTIC, Dawn Gray 1.30 217 6 Finish 40-AW-32 MoPoxY TM MASTIC, White 1.30 217 6 Total Dry Mils 12.0 03.C Epoxy High-Build, High-Solids Primer & Finish Coat Product VOC Sq Ft Mils Prime 41-CH-1 MoPoxY TM -PLUS, Haze Gray 2.36 131 8 Finish 41-CW-1 MoPoxY TM -PLUS, White 2.36 131 8 Total Dry Mils 16.0 Water Storage Tanks Systems 6

WATER STORAGE TANKS - EXTERIOR COATING SYSTEMS 04 WATER TANKS - EXTERIOR COATING SYSTEMS The below systems are representative of the exterior coating systems suitable for this service. For additional systems, please see sections on Ferrous Metal Systems. 04.A Alkyd System, High Gloss, Residential, Commercial & Light Industrial Service Coat Product High Gloss Enamel Finish VOC Sq Ft Mils Shop 9-78 SPEED PRIME Red Oxide Primer 3.76 447 1.5 Prime 10-10 RUS-KIL Metal Primer, Red 3.35 395 2 Intermediate 10-Series RUS-KIL Gloss Enamel 3.35 385 2 Finish 10-Series RUS-KIL Gloss Enamel 3.35 385 2 Total Dry Mils 7.5 04.B Acrylic Latex DTM System, High Gloss, Residential to Light Industrial Service Coat Product High Gloss Acrylic Enamel Finish VOC Sq Ft Mils Shop 310-9 H 2 O RUS-KIL Acrylic Metal Primer, Red 1.14 345 2 Prime 310-9 H 2 O RUS-KIL Acrylic Metal Primer, Red 1.14 345 2 Intermediate 310-Series H 2 O RUS-KIL Acrylic DTM Enamel 1.09 295 2 Finish 310-Series H 2 O RUS-KIL Acrylic DTM Enamel 1.09 295 2 Total Dry Mils 8.0 04.C Silicone Alkyd System, High Gloss, Residential, Commercial & Industrial Service Coat Product High Gloss Silicone Alkyd Enamel Finish VOC Sq Ft Mils Shop 9-78 SPEED PRIME Red Oxide Primer 3.76 447 1.5 Prime 10-10 RUS-KIL Metal Primer, Red 3.35 395 2 Intermediate 432-Series JACK TAR Silicone Yacht Enamel 3.57 484 1.5 Finish 432-Series JACK TAR Silicone Yacht Enamel 3.57 484 1.5 Total Dry Mils 6.5 04.D Catalyzed Epoxy / Epoxy Mastic / Polyurethane System, Heavy Industrial & Marine Service Coat Product High Gloss Polyurethane Finish VOC Sq Ft Mils Shop 613-10 MoPoxY TM HS High Solids Metal Primer 2.00 382 3 Prime 40-AW-32 MoPoxY TM MASTIC, White 1.30 217 6 Intermediate 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 13.0 Water Storage Tanks Systems 7

RECOMMENDED PAINTING SPECIFICATIONS FOR INDUSTRIAL WASTE WATER AND SEWAGE TREATMENT PLANTS INDEX INTRODUCTION SURFACE PREPARATION STANDARDS Part I: FERROUS METALS 01 - Ferrous Metal, Non-Immersion Service 02 - Ferrous Metal, Immersion Service 03 - Galvanized Steel, Non-Immersion Service 04 - Zinc-Rich Primer on Steel, Non-Immersion Service Part II - MASONRY SURFACES 05 - Interior Unplastered Cement Masonry Units 06 - Interior Cement Plaster or Gypsum Board 07 - Exterior Unplastered Cement Masonry Units 08 - Exterior Exposed Concrete or Brick 09 - Exterior Cement Plaster, Stucco or Concrete 10 - Masonry Surfaces, Immersion Service Part III - OTHER 11 - Fiberglass Reinforced Pipe (FRP) 12 - Maintenance Upgrade Systems Product Data Sheets and Color Cards will be found at the back of this book. Waste Water Treatment Plants 1

RECOMMENDED PAINTING SPECIFICATIONS FOR INDUSTRIAL WASTE WATER AND SEWAGE TREATMENT PLANTS INTRODUCTION Because of the aggressive atmosphere of sewage and waste water treatment plants and the difficulty of maintenance after these plants have been placed in operation, we have limited our recommendations to those high-performance systems and products which have been proven to offer the longest service life. In general, we recommend catalyzed epoxy and polyurethane coatings throughout for their exceptional resistance to chemicals, fumes, abrasion and moisture. Applied as specified over a properly prepared substrate, they will give years of service under adverse conditions with a minimum of maintenance while retaining their color and gloss to provide an attractive and easily cleaned plant. In addition to a large selection of standard colors, custom colors are available in keeping with the modern tradition of making our work places and necessary plants as attractive as possible. Originally written for new construction only, the scope of this specification has been expanded to include upgrading deteriorated paint systems where sandblasting is not feasible or practical but high performance is required. All products recommended are lead-free, chromate-free, and mercury-free, with the exception of Vinyl Wash Primer, which is required for adhesion of topcoats on galvanized metal, and which contains zinc chromate. All systems are VOC-Compliant. Surface preparation is indicated for critical areas, such as surfaces subjected to immersion service. All products are formulated for application by airless spray but may be applied by brush or roller unless otherwise indicated. If applied by roller, high-build formulations will normally require two coats for each 3 mils specified as it is difficult to apply more than 3 mils per coat by roller. For detailed recommendations covering specific problems, please consult your BLP Mobile Paint representative. Waste Water Treatment Plants 2

RECOMMENDED PAINTING SPECIFICATIONS FOR INDUSTRIAL WASTE WATER AND SEWAGE TREATMENT PLANTS SURFACE PREPARATION The Society for Protective Coatings, formerly the Steel Structures Painting Council, is the recognized authority on surface preparation and reference is made to their standards as follows: Solvent Cleaning SSPC-SP 1 Hand Cleaning SSPC-SP 2 Power Tool Cleaning SSPC-SP 3 White Metal Blast SSPC-SP 5 Commercial Blast SSPC-SP 6 Brush-off Blast SSPC-SP 7 Near White Blast SSPC-SP 10 Power Tool Cleaning to Bare Metal SSPC-SP 11 Commercial Sandblast iaw SSPC-SP 6 should be considered as the minimum acceptable surface preparation for nonimmersion service. White Metal Blast iaw SSPC-SP 5 is the minimum acceptable surface preparation for steel in immersion service. Brush-off Blast iaw SSPC-SP 7 is recommended for concrete surfaces in immersion service. Wet sandblasting is becoming more common because of stringent EPA regulations, requiring new techniques and the use of additives in the blasting water to prevent immediate rust bloom. Consult your BLP Mobile Paint representative for equipment and additive recommendations. Shop coats and primers for piping, pumps and non-critical areas must be compatible with the finish system specified. After erection, all nuts, bolts, abraded areas and scratches should be Hand Cleaned (SSPC-SP 2) or Power Tool Cleaned (SSPC-SP ) and spot primed before additional coats of primer or finish are applied. Welds should be ground to remove weld splatter before priming. Waste Water Treatment Plants 3

01 FERROUS METAL SYSTEMS, NON-IMMERSION SERVICE This section covers ferrous metals, including structural steel, non-galvanized roof deckings, tanks and silos, tubing, pipe racks, platforms, ladders, siding, doors and door frames and equipment, both interior and exterior, subject to weathering, splashing and mild fumes, at ambient temperatures in sewage and waste water treatment plants. Not for immersion service. All systems are lead-free, chromate-free, mercury-free, and VOC compliant. Surface Preparation: Application: Commercial Blast, SSPC-SP 6, preferred minimum Power Tool Clean, SSPC-SP 2, minimum for non-critical areas Solvent Clean, SSPC-SP 1, to remove oil or grease Airless spray preferred, conventional spray, brush or roller 01.A Catalyzed Epoxy/Polyurethane System, Severe Service, Exterior Coat Product High Gloss Catalyzed Polyurethane Finish VOC Sq.Ft. Mils Prime 613-10 MoPoxY HS High Solids Metal Primer 2.00 382 3 Intermediate 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Total Dry Mils 13.0 01.B Catalyzed Epoxy/Acrylic Epoxy, Severe Service, Exterior Coat Product High Gloss Acrylic Epoxy Finish VOC Sq.Ft. Mils Prime 613-10 MoPoxY HS High Solids Metal Primer 2.00 382 3 Intermediate 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 41-AW-2 MOPOX-ACRYL White 3.50 409 2 Finish 41-AW-2 MOPOX-ACRYL White 3.50 409 2 Total Dry Mils 13.0 01.C Catalyzed Epoxy Mastic/High-Solids Polyurethane System, Severe Service, Exterior Coat Product High Gloss Catalyzed Polyurethane Finish VOC Sq.Ft. Mils Prime 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Intermediate 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Total Dry Mils 16.0 Waste Water Treatment Plants 4

01.D Catalyzed Epoxy System, Semi-Gloss, Severe Service, Interior Coat Product Semi-Gloss Catalyzed Epoxy Finish VOC Sq.Ft. Mils Prime 613-10 MoPoxY HS High Solids Metal Primer 2.00 382 3 Intermediate 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.10 374 3 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.10 374 3 Total Dry Mils 15.0 01.E Epoxy Mastic/Catalyzed Epoxy System, Semi-Gloss, Severe Service, Interior Coat Product Semi-Gloss Catalyzed Epoxy Finish VOC Sq.Ft. Mils Prime 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Intermediate 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.10 374 3 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.10 374 3 Total Dry Mils 18.0 01.F Catalyzed Waterborne Epoxy System, Semi-Gloss, Moderate Service, Interior Coat Product Semi-Gloss Waterborne Amide Epoxy VOC Sq.Ft. Mils Prime 69-DR-1 MoPoxY H 2 O-200 Metal Primer 0.89 257 3 Intermediate 69-DR-1 MoPoxY H 2 O-200 Metal Primer 0.89 257 3 Finish 69-AW-6 MoPoxY H 2 O-200 Amide Epoxy 1.00 225 3 Finish 69-AW-6 MoPoxY H 2 O-200 Amide Epoxy 1.00 225 3 Total Dry Mils 12.0 Waste Water Treatment Plants 5

02 FERROUS METALS, IMMERSION SERVICE This section covers ferrous metal, including holding and settling tanks and aeration equipment, structural steel, ladders and platforms subject to immersion service at ambient temperatures. Surface Preparation: Application: White Metal Blast, SSPC-SP 5, minimum acceptable Airless Spray preferred. May be brushed or rolled unless otherwise noted. 02.A Glass Flake Phenolic Epoxy System Coat Product Severe service, Maximum protection VOC Sq.Ft. Mils Prime 41-AH-2 MoPoxY GF Light Gray 2.65 122 8 Intermediate 41-AH-2 MoPoxY GF Light Gray 2.65 122 8 Finish 41-AH-2 MoPoxY GF Light Gray 2.65 122 8 Apply by airless spray only Total Dry Mils 24.0 02.B Epoxy Mastic Coating System Coat Product Severe service, Low-VOC VOC Sq.Ft. Mils Prime 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 40-AH-51 MoPoxY MASTIC, Gray 1.30 217 6 Finish 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Total Dry Mils 18.0 02.C Coal Tar Epoxy Coating System Coat Product Severe service, Low-VOC VOC Sq.Ft. Mils Prime 40-AX-7 MO-TAR C-200 Coal Tar Epoxy Coating 1.56 157 8 Finish 40-AX-7 MO-TAR C-200 Coal Tar Epoxy Coating 1.56 157 8 Finish 40-AX-7 MO-TAR C-200 Coal Tar Epoxy Coating 1.56 157 8 Total Dry Mils 24.0 02.D High-Build Coal Tar Epoxy Coating System Coat Product Polyamide Coal Tar Epoxy VOC Sq.Ft. Mils Prime & 40-BX-6 MO-TAR HB-90 Coal Tar Epoxy Coating 1.13 67 20 Finish Total Dry Mils 20.0 Waste Water Treatment Plants 6

03 GALVANIZED STEEL, NON-IMMERSION SERVICE Galvanized steel decking, piping, and similar items are customarily factory coated with oil to prevent galvanic action while stacked. This must be removed prior to painting either by Solvent Cleaning iaw SSPC-SP 1, or by washing with a detergent solution and rinsing with clear water. Galvanized steel requires a pretreatment to insure adhesion of subsequent coats. Surface Preparation: Pretreatment: Solvent Clean, SSPC-SP1, to remove oil or grease Vinyl Wash Primer to promote adhesion 03.A Galvanized Steel, Catalyzed Epoxy/High-Solids Polyurethane System, Exterior Service Coat Product High Gloss Catalyzed Polyurethane Finish VOC Sq.Ft. Mils Pre-Treat 9-42 VINYL WASH Primer 5.72 252 0.5 Prime 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Total Dry Mils 10.5 03.B Galvanized Steel, Catalyzed Epoxy System, Semi-Gloss, Interior Service Coat Product Semi-Gloss Catalyzed Epoxy Finish VOC Sq.Ft. Mils Pre-Treat 9-42 VINYL WASH Primer 5.72 252 0.5 Prime 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.10 374 3 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.10 374 3 Total Dry Mils 12.5 03.C Catalyzed Waterborne Epoxy System, Semi-Gloss, Interior Service Coat Product Semi-Gloss WB Amide Cured Epoxy Finish VOC Sq.Ft. Mils Pre-Treat 9-42 VINYL WASH Primer 5.72 252 0.5 Prime 69-DR-1 MoPoxY H 2 O-200 Metal Primer 0.89 257 3 Finish 69-AW-6 MoPoxY H 2 O-200 Amide Epoxy 1.00 225 3 Finish 69-AW-6 MoPoxY H 2 O-200 Amide Epoxy 1.00 225 3 Total Dry Mils 9.5 Waste Water Treatment Plants 7

04 ZINC-RICH PRIMER ON STEEL, NON-IMMERSION SERVICE Inorganic zinc requires a clean surface and good anchor pattern, best achieved by sandblasting. White Metal Blast, SSPC-SP 5, is preferred. Commercial Sandblast, SSPC-SP 6 is minimum acceptable. Apply by airless or conventional spray with constant mechanical agitation. MoPoxY MASTIC may be applied directly over inorganic zinc by airless spray if a mist coat is applied first to penetrate the pores of the zinc, followed by a full coat. If applied by brush or roller, vinyl wash primer is required. Surface Preparation: Application, Zinc: Application, Epoxy: White Metal Blast, SSPC-SP 5, Preferred Commercial Sandblast, SSPC-SP 6, Minimum acceptable Airless or Conventional Spray with constant mechanical agitation. Airless spray: Apply mist coat of epoxy to zinc, follow with full body coat. Brush or roller: Pretreat with Vinyl Wash Primer 04.A Inorganic Zinc/Epoxy Mastic/High-Solids Polyurethane System, Exterior Service Coat Product High Gloss Polyurethane Finish VOC Sq.Ft. Mils Prime 28-DH-50 MO-ZINC Inorganic Zinc Primer 3.88 342 3 Intermediate Finish 40-AW-32 72-AW-26 MoPoxY MASTIC, White MOTHANE HS-1000 Polyurethane, White 1.20 2.45 217 513 6 2 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Total Dry Mils 13.0 04.B Inorganic Zinc/Epoxy Mastic/Acrylic Epoxy System, Exterior Service Coat Product High Gloss Acrylic Epoxy Finish VOC Sq.Ft. Mils Prime 28-DH-50 MO-ZINC Inorganic Zinc Primer 3.88 342 3 Intermediate Finish 40-AW-32 41-AW-2 MoPoxY MASTIC, White MOPOX-ACRYL Acrylic Epoxy 1.30 3.50 217 409 6 2 Finish 41-AW-2 MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 13.0 04.C Inorganic Zinc/Epoxy Mastic/Semi-Gloss Epoxy System, Interior Service Coat Product Semi-Gloss Epoxy Finish VOC Sq.Ft. Mils Prime 28-DH-50 MO-ZINC Inorganic Zinc Primer 3.88 342 3 Intermediate Finish 40-AW-32 613-17 MoPoxY MASTIC, White MoPoxY HS High Solids Epoxy, White 1.30 2.10 217 374 6 3 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.10 374 3 Total Dry Mils 15.0 Waste Water Treatment Plants 8

04.D Inorganic Zinc/Waterborne Epoxy System, Interior Service Coat Product Semi-Gloss WB Amide Epoxy Finish VOC Sq.Ft. Mils Prime 28-DH-50 MO-ZINC Inorganic Zinc Primer 3.88 342 3 Intermediate 9-42 VINYL WASH Primer 5.72 252 0.5 Finish 69-AW-6 MoPoxY H2O-200 Amide Epoxy 1.00 225 3 Finish 69-AW-6 MoPoxY H2O-200 Amide Epoxy 1.00 225 3 Total Dry Mils 9.5 Zinc-rich epoxy primers combine the improved wetting properties and chemical and abrasion resistance of a catalyzed epoxy with the sacrificial protection afforded by inorganic zinc. Excellent resistance to fresh and salt water, detergents and most chemicals, abrasion and moisture. Excellent for touchup of inorganic zinc primers. VOC Compliant Surface Preparation: Application: Commercial Sandblast, SSPC-SP 6, recommended minimum Power Tool Clean, SSPC-SP 2, minimum acceptable Airless or conventional spray with continuous mechanical agitation 04.E Zinc-Rich Epoxy/Epoxy Mastic/High-solids Polyurethane System, Exterior Service Coat Product High Gloss Polyurethane Finish VOC Sq.Ft. Mils Prime 40-CM-4 MoPoxY ZR Zinc Rich Epoxy Primer 3.89 257 3.5 Intermediate 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Total Dry Mils 13.5 Total Dry Mils ERR 04.F Zinc-Rich Epoxy/Epoxy Mastic/Semi-Gloss Epoxy, Interior Service Coat Product Semi-Gloss Epoxy Finish VOC Sq.Ft. Mils Prime 40-CM-4 MoPoxY ZR Zinc Rich Epoxy Primer 3.89 257 3.5 Intermediate 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.00 374 3 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.00 374 3 Total Dry Mils 15.5 Waste Water Treatment Plants 9

05 INTERIOR EXPOSED MASONRY UNITS, NON-IMMERSION SERVICE 05.A Catalyzed Semi-Gloss Epoxy System, Interior Service Coat Product Semi-Gloss Epoxy Finish VOC Sq.Ft. Mils Fill 19-10 BLOC-SEAL 0.44 100 1 Prime 19-7 PRYMALL 2 QD Primer & Sealer 1.13 302 1.5 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.00 374 3 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.00 374 3 Total Dry Mils 8.5 05.B Waterborne Catalyzed Epoxy System, Interior Service Coat Product Semi-Gloss Waterborne Amide Epoxy Finish VOC Sq.Ft. Mils Fill 19-10 BLOC-SEAL 0.44 100 1 Prime 19-7 PRYMALL 2 QD Primer & Sealer 1.13 302 1.5 Finish 69-AW-6 MoPoxY H20-200 WB Amide-Epoxy 1.00 225 3 Finish 69-AW-6 MoPoxY H20-200 WB Amide-Epoxy 1.00 225 3 Total Dry Mils 8.5 06 INTERIOR CEMENT PLASTER OR GYPSUM BOARD 06.A Catalyzed Semi-Gloss Epoxy System, Interior Service Coat Product Semi-Gloss Epoxy Finish VOC Sq.Ft. Mils Prime 19-7 PRYMALL 2 QD Primer & Sealer 1.13 302 1.5 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.00 374 3 Finish 613-17 MoPoxY HS High Solids Epoxy, White 2.00 374 3 Total Dry Mils 7.5 06.B Waterborne Catalyzed Epoxy System, Interior Service Coat Product Semi-Gloss Waterborne Amide Epoxy Finish VOC Sq.Ft. Mils Prime 19-7 PRYMALL 2 QD Primer & Sealer 1.13 302 1.5 Finish 69-AW-6 MoPoxY H20-200 WB Amide-Epoxy 1.00 225 3 Finish 69-AW-6 MoPoxY H20-200 WB Amide-Epoxy 1.00 225 3 Total Dry Mils 7.5 Waste Water Treatment Plants 10

07 EXTERIOR UNPLASTERED CEMENT MASONRY UNITS WEATHER-TITE TM Acrylic House Paint is the industry standard for exterior masonry finishes. 100% acrylic, it transpires, allowing moisture in the masonry to evaporate without damaging the paint film. Highly resistant to alkali. Contains an effective mildewcide. Excellent color retention. 07.A Acrylic Latex System, Flat Finish Coat Product Acrylic Latex Flat Finish VOC Sq.Ft. Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 Prime 6-6 WEATHER-TITE TM 100% Acrylic Universal Primer 1.17 393 2 Finish 40-Series WEATHER-TITE TM 100% Acrylic House Paint 1.03 291 2 Finish 40-Series WEATHER-TITE TM 100% Acrylic House Paint 1.03 291 2 Total Dry Mils 7.0 07.B Acrylic Latex System, Gloss Finish Coat Product Acrylic Latex, High Semi-Gloss Finish VOC Sq.Ft. Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 Prime 6-6 WEATHER-TITE TM 100% Acrylic Universal Primer 1.17 393 2 Finish 140-Series WEATHER-TITE TM 100% Acrylic House Paint 1.99 296 2 Finish 140-Series WEATHER-TITE TM 100% Acrylic House Paint 1.99 296 2 Total Dry Mils 7.0 07.C Acrylic Latex System, Satin Finish Coat Product Acrylic Latex, Satin Gloss Finish VOC Sq.Ft. Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 Prime 6-6 WEATHER-TITE TM 100% Acrylic Universal Primer 1.17 393 2 Finish 240-Series WEATHER-TITE TM 100% Acrylic House Paint 2.19 271 2 Finish 240-Series WEATHER-TITE TM 100% Acrylic House Paint 2.19 271 2 Total Dry Mils 7.0 Waste Water Treatment Plants 11

07.D Elastomeric Acrylic System WEATHER-TITE TM Elastomeric Wall Coat is 100% acrylic and offers exceptional resistance to alkali, moisture, sun, and mildew. Bridges small cracks, protects against wind driven rain. Excellent for maintenance upgrade service where existing paints have failed. Coat Product Acrylic Latex Elastomeric Finish VOC Sq.Ft. Mils Fill 60-7 BLOC-FIL Latex Block Filler 0.55 100 1 Prime 6-6 WEATHER-TITE TM 100% Acrylic Universal Primer 1.17 393 2 Finish 43-25 WEATHER-TITE TM ELASTOMERIC Wall Coat 0.80 100 7.5 Finish 43-25 WEATHER-TITE TM ELASTOMERIC Wall Coat 0.80 100 7.5 Total Dry Mils 18.0 08 EXTERIOR EXPOSED CONCRETE OR BRICK WEATHER-TITE TM DUB-L-TITE is a clear silicone sealer which penetrates into the pores of the surface and forms an invisible barrier to repel water. Does not change the appearance of the substrate. Recommended for exposed concrete, exposed aggregate, brick and similar surfaces. H 2 O DUB-L-TITE is a waterborne silicone/silane formulation offering low VOC and low odor. 08.A Clear Silicone Sealer & Water Repellant Coat Product VOC Sq.Ft. Mils Prime 74-12 DUB-L-TITE TM Silicone Sealer, Clear 6.19 100 1 Finish 74-12 DUB-L-TITE TM Silicone Sealer, Clear 6.19 100 1 Total Dry Mils 2.0 08.B Clear Waterborne Silicone/Silane Sealer & Water Repellant Coat Product VOC Sq.Ft. Mils Prime 74-13 H 2 O DUB-L-TITE Silicone Sealer, Clear 0.00 100 1 Finish 74-13 H 2 O DUB-L-TITE Silicone Sealer, Clear 0.00 100 1 Total Dry Mils 2.0 Waste Water Treatment Plants 12

09 EXTERIOR CEMENT PLASTER, STUCCO OR CONCRETE 09.A Acrylic Latex System, Flat Finish Coat Product Acrylic Latex Flat Finish VOC Sq.Ft. Mils Prime 6-6 WEATHER-TITE TM 100% Acrylic Universal Primer 1.17 393 2 Finish 40-Series WEATHER-TITE TM 100% Acrylic House Paint 1.03 291 2 Finish 40-Series WEATHER-TITE TM 100% Acrylic House Paint 1.03 291 2 Total Dry Mils 6.0 09.B Acrylic Latex System, Gloss Finish Coat Product Acrylic Latex, High Semi-Gloss Finish VOC Sq.Ft. Mils Prime 6-6 WEATHER-TITE TM 100% Acrylic Universal Primer 1.17 393 2 Finish 140-Series WEATHER-TITE TM 100% Acrylic House Paint 1.99 296 2 Finish 140-Series WEATHER-TITE TM 100% Acrylic House Paint 1.99 296 2 Total Dry Mils 6.0 09.C Acrylic Latex System, Satin Finish Coat Product Acrylic Latex, Satin Gloss Finish VOC Sq.Ft. Mils Prime 6-6 WEATHER-TITE TM 100% Acrylic Universal Primer 1.17 393 2 Finish 240-Series WEATHER-TITE TM 100% Acrylic House Paint 2.19 271 2 Finish 240-Series WEATHER-TITE TM 100% Acrylic House Paint 2.19 271 2 Total Dry Mils 6.0 09.D Elastomeric Acrylic Latex System Coat Product Acrylic Latex, Elastomeric Finish VOC Sq.Ft. Mils Prime 6-6 WEATHER-TITE TM 100% Acrylic Universal Primer 1.17 393 2 Finish 43-25 WEATHER-TITE TM ELASTOMERIC Wall Coat 0.80 100 7.5 Finish 43-25 WEATHER-TITE TM ELASTOMERIC Wall Coat 0.80 100 7.5 Total Dry Mils 17.0 Waste Water Treatment Plants 13

10 MASONRY SURFACES, IMMERSION SERVICE Masonry surfaces subject to immersion service require either Brush Blasting, SSPC-SP 7, or acid etching with muriatic acid to remove laitance and provide the porosity required for good adhesion. 10.A Glass Flake Phenolic Epoxy System Coat Product Maximum abrasion & chemical resistance VOC Sq.Ft. Mils Prime 41-AH-2 MoPoxY GF Light Gray 2.65 122 8 Second 41-AH-2 MoPoxY GF Light Gray 2.65 122 8 Finish 41-AH-2 MoPoxY GF Light Gray 2.65 122 8 Apply by airless spray, only. Total Dry Mils 24.0 10.B Epoxy Mastic Coating Coat Product Severe service VOC Sq.Ft. Mils Prime 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 40-AH-51 MoPoxY MASTIC, Gray 1.30 217 6 Finish 40-AH-51 MoPoxY MASTIC, Gray 1.30 217 6 Total Dry Mils 18.0 10.C Coal Tar Epoxy Coating System Coat Product Severe service VOC Sq.Ft. Mils Prime 40-AX-7 MO-TAR C-200 Coal Tar Epoxy Coating 1.56 157 8 Finish 40-AX-7 MO-TAR C-200 Coal Tar Epoxy Coating 1.56 157 8 Finish 40-AX-7 MO-TAR C-200 Coal Tar Epoxy Coating 1.56 157 8 Total Dry Mils 24.0 10.D High-Build Coal Tar Epoxy Coating System Coat Product Severe service VOC Sq.Ft. Mils Prime* 40-BX-6 MO-TAR HB-90 Coal Tar Epoxy Coating 1.13 67 20 Finish 40-BX-6 MO-TAR HB-90 Coal Tar Epoxy Coating 1.13 67 20 * Thin up to 20% with MoPoxY Spraying Thinner 75-37 Total Dry Mils 40.0 Waste Water Treatment Plants 14

11 FIBERGLASS REINFORCED PIPE (FRP) 11.A Epoxy/High-Solids Polyurethane System, Exterior Service Coat Product High Gloss Polyurethane Finish VOC Sq.Ft. Mils Surface Preparation: Wet Sand with 50:50 water/al-co-sol solution Prime 613-17 MoPoxY HS High Solids White 2.00 374 3 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane, White 2.45 513 2 Total Dry Mils 7.0 11.B Epoxy System, High-Solids, Semi-Gloss, Interior Service Coat Product Semi-Gloss Epoxy Finish VOC Sq.Ft. Mils Surface Preparation: Wet Sand with 50:50 water/al-co-sol solution Prime 613-17 MoPoxY HS High Solids White 2.00 374 3 Finish 613-17 MoPoxY HS High Solids White 2.00 374 3 Total Dry Mils 6.0 Waste Water Treatment Plants 15

12 MAINTENANCE UPGRADE SYSTEMS For upgrading deteriorated alkyd or silicone alkyd finishes and repairing catalyzed epoxy and polyurethane systems where sandblasting is not possible to remove existing coatings. MoPoxY MASTIC is a high-solids, high-build, surface-tolerant amine epoxy formulated for application over sound rust and/or deteriorated paint systems as a base coat for upgrading to high performance coatings such as acrylic epoxies or polyurethanes. MoPoxY IR, Indefinite Recoatablity Epoxy, is a high-solids, surface-tolerant, high-build coating which may be applied to damp, rusty surfaces, allowed to dry for prolonged periods, then topcoated with other epoxies or polyurethanes without loss of intercoat adhesion. MoPoxY PRE-PREP is a 100% solids epoxy with very low viscosity and excellent substrate wetting properties. Excellent for badly rusted areas where sandblasting and removal of existing coatings is not feasible and only minimal cleaning is possible. Penetrates and bonds rust and deteriorated coatings into a solid film which seals out moisture and oxygen. Allow to cure for 24 hours, then apply recommended intermediate coat while still slightly soft. Will accept a wide variety of coatings. All systems are lead-free, chromate-free, mercury-free and VOC compliant. Surface Preparation: Application: Pressure Wash (3,000 psi or better) to remove contamination Solvent Clean, SSPC-SP 1, to remove oil and grease Power Tool Clean, SSPC-SP 2, preferred Hand Tool Clean, SSPC-CP 3, minimum recommended Brush, roller, or airless or conventional spray 12.A Catalyzed Epoxy Mastic/Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq.Ft. Mils Spot Prime 40-AY-2 MoPoxY MASTIC, Aluminum 0.51 248 6 Prime 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 16.0 Waste Water Treatment Plants 16

12.B Catalyzed Epoxy Mastic/Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq.Ft. Mils Spot Prime 40-AY-2 MoPoxY MASTIC, Aluminum 0.51 248 6 Prime 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 16.0 12.C Recoatable Epoxy/Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq.Ft. Mils Spot Prime 41-BK-14 MoPoxY IR High Solids Epoxy Buff 2.29 136 8 Prime 41-BK-14 MoPoxY IR High Solids Epoxy Buff 2.29 136 8 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-AW-26 MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 20.0 12.D Recoatable Epoxy/Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq.Ft. Mils Spot Prime 41-BK-14 MoPoxY IR High Solids Epoxy Buff 2.29 136 8 Prime 41-BK-14 MoPoxY IR High Solids Epoxy Buff 2.29 136 8 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 20.0 12.E Low-Viscosity Epoxy/Epoxy Mastic/Polyurethane System Coat Product High Gloss Polyurethane Finish VOC Sq.Ft. Mils Prime 41-AF-2 MoPoxY PRE-PREP Clear 0.00 1069 1.5 Intermediate 40-AW-32 MoPoxY MASTIC, White 1.30 217 6 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Finish 72-Series MOTHANE HS-1000 Polyurethane 2.45 513 2 Total Dry Mils 11.5 Waste Water Treatment Plants 17

12-F Low-Viscosity Epoxy/Epoxy Mastic/Acrylic Epoxy System Coat Product High Gloss Acrylic Epoxy Finish VOC Sq.Ft. Mils Prime 41-AF-2 MOPOXY PRE-PREP Clear 0.00 1069 1.5 Intermediate 40-AW-32 MOPOXY MASTIC, White 1.30 217 6 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Finish 41-Series MOPOX-ACRYL Acrylic Epoxy 3.50 409 2 Total Dry Mils 11.5 Waste Water Treatment Plants 18

RECOMMENDED PAINTING SPECIFICATIONS FOR MARINE COATING SYSTEMS Painting Recommendations For Ships and Boats Steel, Fiberglass and Wood Part I INTRODUCTION Introduction to Coating Systems and Surface Preparation Part II INDEX OF COATING SYSTEMS Detailed Index of Coating Systems Part III COATING SYSTEMS Recommended Surface Preparation, Primers, Intermediate Coats Finish Coats, Dry Film Thickness and Coverage SUMMARY INDEX 01 - Steel Vessels - Exterior - Above Water Line 02 - Steel Vessels - Exterior - Below Water Line 03 - Steel Vessels - Exterior - Decks & Ladders 04 - Steel Vessels - Interior - Bulkhead & Overhead 05 - Steel Vessels - Interior - Ladders, Decks & Passageways 06 - Fiberglass Vessels - Exterior - Above Water Line 07 - Fiberglass Vessels - Exterior - Below Water Line 08 - Fiberglass Vessels - Exterior - Decks & Ladders 09 - Fiberglass Vessels - Interior - Bulkhead & Overhead 10 - Fiberglass Vessels - Interior - Ladders, Decks & Passageways 11 - Wooden Vessels - Exterior - Above Water Line 12 - Wooden Vessels - Exterior - Below Water Line 13 - Wooden Vessels - Exterior - Decks & Ladders 14 - Wooden Vessels - Interior - Bulkhead & Overhead 15 - Wooden Vessels - Interior - Ladders, Decks & Passageways 16 - Engine Room 17 - Potable Water Tanks 18 - Fuel Tanks 19 - Bilges & Voids INDEX OF PRODUCT DATA SHEETS Marine Coating Systems 1

RECOMMENDED PAINTING SPECIFICATIONS FOR MARINE COATING SYSTEMS Part I Introduction Marine coatings are a unique group, in that they must resist the harshest of environments. They must protect from constant salt water spray, high humidity, impact, abrasion, high temperatures, immersion and fouling, as well as, intense assault from sunlight and ultraviolet rays. In order to simplify the selection, we will present several recommended systems for each area to be coated. Surface preparation, primers, intermediate and topcoats are listed for both interior and exterior surfaces. Systems are listed in inverse order of service life. Surface preparation is the key to the life expectancy of any coating system. It is even more critical in the case of marine coatings. Each system will contain a recommended surface preparation for steel, fiberglass and wood. While most products listed may be rolled or brushed, they are best applied by spray. Mobile Paint Manufacturing Co., Inc. has over 80 years experience in formulating and manufacturing top quality industrial, marine and architectural coatings for tropical and subtropical climates. We manufacture an extensive line of items for specialized services including tank linings for chemicals, potable water tanks, fuel and oil tanks, high heat coatings and numerous Military Specification coatings. Please contact your Mobile Paint Manufacturing Co., representative for specific recommendations for particular needs. Marine Coating Systems 2

01 Steel Vessels - Exterior - Above Water Line RECOMMENDED PAINTING SPECIFICATIONS FOR MARINE COATING SYSTEMS Part II Index of Coating Systems 01.A MoPoxY TM ZR / MoPoxY TM Plus / MOTHANE TM Polyurethane System 01.B JackTar Phenolic / JackTar Silicone Alkyd System 01.C Alkyd / JackTar Silicone Alkyd EnamelSystem 01.D Alkyd / JackTar Alkyd Enamel System 02 Steel Vessels - Exterior - Below Water Line 02.A MoPoxY TM Plus / JackTar Vinyl Antifouling System 02.B JackTar Phenolic / JackTar Cold Plastic Antifouling System 02.C JackTar Phenolic / JackTar Dub-L-Cop Antifouling System 03 Steel Vessels - Exterior - Decks & Ladders 03.A MoPoxY TM ZR / MoPoxY TM HS / MoPoxY TM AR-200 Deck Armor High Build System 03.B MoPoxY TM ZR / MoPoxY TM HS / MoPoxY TM NS-200 Deck Armor High Build Non-Skid System 03.C MoPoxY TM ZR / MoPoxY TM HS Epoxy System 04 Steel Vessels - Interior - Bulkhead & Overhead 04.A MoPoxY TM HS Epoxy System 04.B Rus-Kil Rust Inhibitive Enamel System 05 Steel Vessels - Interior - Ladders, Decks & Passageways 05.A MoPoxY TM HS Epoxy System 05.B Rus-Kil / JackTar Alkyd Enamel System 06 Fiberglass Vessels - Exterior - Above Water Line 06.A MoPoxY TM Plus / MOTHANE TM Polyurethane System 06.B JackTar Silicone Alkyd Enamel System 06.C JackTar Alkyd Enamel System Marine Coating Systems 3

07 Fiberglass Vessels - Exterior - Below Water Line RECOMMENDED PAINTING SPECIFICATIONS FOR MARINE COATING SYSTEMS Part II Index of Coating Systems (continued) 07.A MoPoxY TM Plus / JackTar Vinyl Antifouling System 07.B JackTar Phenolic / JackTar Cold Plastic Antifouling System 07.C JackTar Phenolic / JackTar Dub-L-Cop Antifouling System 08 Fiberglass Vessels - Exterior - Decks & Ladders 08.A MoPoxY TM HS / MoPoxY TM AR-200 Deck Armor High Build System 08.B MoPoxY TM HS / MoPoxY TM NS-200 Deck Armor High Build Non-Skid System 08.C MoPoxY TM HS Epoxy System 09 Fiberglass Vessels - Interior - Bulkhead & Overhead 09.A MoPoxY TM HS Epoxy System 09.B Rus-Kil Rust Inhibitive Enamel System 10 Fiberglass Vessels - Interior - Ladders, Decks & Passageways 10.A MoPoxY TM HS Epoxy System 10.B Rus-Kil Primer / JackTar Alkyd Enamel System 11 Wooden Vessels - Exterior - Above Water Line 11.A MoPoxY TM Plus / MOTHANE TM Polyurethane System 11.B JackTar Silicone Alkyd Enamel System 11.C JackTar Alkyd Enamel System 12 Wooden Vessels - Exterior - Below Water Line 12.A MoPoxY TM Plus / JackTar Vinyl Antifouling System 12.B JackTar Phenolic / JackTar Cold Plastic Antifouling System 12.C JackTar Phenolic / JackTar Dub-L-Cop Antifouling System Marine Coating Systems 4

13 Wooden Vessels - Exterior - Decks & Ladders RECOMMENDED PAINTING SPECIFICATIONS FOR MARINE COATING SYSTEMS Part II Index of Coating Systems (continued) 13.A MoPoxY TM HS / MoPoxY TM AR-200 Deck Armor High Build System 13.B MoPoxY TM HS / MoPoxY TM NS-200 Deck Armor High Build Non-Skid System 13.C MoPoxY TM HS Epoxy System 14 Wooden Vessels - Interior - Bulkhead & Overhead 14.A MoPoxY TM HS Epoxy System 14.B Rus-Kil Rust Inhibitive Enamel System 15 Wooden Vessels - Interior - Ladders, Decks & Passageways 15.A MoPoxY TM HS Epoxy System 15.B Rus-Kil Primer / JackTar Alkyd Enamel System 16 Engine Room 16.A MoPoxY TM HS Epoxy System 16.B Rus-Kil Primer / JackTar Alkyd Enamel System 17 Potable Water Tanks 17.A MoPoxY TM HS-50 NSF Epoxy System 18 Fuel Tanks 18.A MoPoxY TM Mastic Epoxy System 19 Bilges & Voids 19.A MoPoxY TM Plus Epoxy System Marine Coating Systems 5

Part III Coating Systems for Ships and Boats Section 01 STEEL VESSELS - EXTERIOR - ABOVE WATER LINE Surface Preparation: minimum acceptable. Near White Metal Sandblast (SSPC-SP10) is preferred and Commercial Sandblast (SSPC-SP6) is 01.A MoPoxY TM ZR / MoPoxY TM Plus / MOTHANE TM Polyurethane System Combines excellent chemical, solvent and abrasion resistance with superior gloss and color retention for maximum service. Coat Product Description Sq.Ft Mils Prime 40-CM-4 MoPoxY ZR Zinc Rich Epoxy Primer 257 3.5 Intermediate 41-CW-1 MoPoxY TM Plus Epoxy Coating 131 8 Finish * 72-series MOTHANE TM Polyurethane Coating 339 2 Finish * 72-series MOTHANE TM Polyurethane Coating 339 2 * Alternate Finish 72-series MOTHANE TM HD Polyurethane Coating 268 2.5 * Alternate Finish 72-series MOTHANE TM HS-1000 Polyurethane Coating 513 2 * Alternate Finish 72-series MOTHANE TM HS-900 Polyurethane Coating 428 2.5 Total Dry Mils 15.5 16.5 01.B JackTar Phenolic / JackTar Silicone Alkyd System Combines easier application with good resistance properties and excellent color and gloss retention. Coat Product Description Sq.Ft Mils Prime 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Finish 432-line JACK TAR Silicone Yacht Finish 484 1.5 Finish 432-line JACK TAR Silicone Yacht Finish 484 1.5 Total Dry Mils 9.0 Marine Coating Systems 6

Part III Coating Systems for Ships and Boats Section 01 STEEL VESSELS - EXTERIOR - ABOVE WATER LINE (continued): 01.C Alkyd / JackTar Silicone Alkyd EnamelSystem Provides greater economy, ease of application and excellent color and gloss retention. Coat Product Description Sq.Ft Mils Prime 10-10 RUS-KIL Metal Primer 337 2 Intermediate 10-10 RUS-KIL Metal Primer 337 2 Finish 432-line JACK TAR Silicone Yacht Finish 484 1.5 Finish 432-line JACK TAR Silicone Yacht Finish 484 1.5 Total Dry Mils 7.0 01.D Alkyd / JackTar Alkyd Enamel System Economic protection in mild marine service. Good color and gloss retention. Coat Product Description Sq.Ft Mils Prime 10-10 RUS-KIL Metal Primer 337 2 Finish 450-line JACK TAR Yacht Deck Enamel 420 1.5 Finish 450-line JACK TAR Yacht Deck Enamel 420 1.5 Total Dry Mils 5.0 Marine Coating Systems 7

Part III Coating Systems for Ships and Boats Section 02 STEEL VESSELS - EXTERIOR - BELOW WATER LINE Surface Preparation: is minimum acceptable. Near White Metal Sandblast (SSPC-SP10) is preferred and Commercial Sandblast (SSPC-SP6) 02.A MoPoxY TM Plus / JackTar Vinyl Antifouling System Offers maximum durability for steel vessels. This system consists of two coats of high solids, high build epoxy primer and two coats of cuprous oxide, vinyl copolymer, anti-fouling paint. Coat Product Description Sq.Ft Mils Prime 41-CW-1 MoPoxY TM Plus Epoxy Coating 131 8 Intermediate 41-CW-1 MoPoxY TM Plus Epoxy Coating 131 8 Finish 473-73 JACK TAR Vinyl Anti-fouling Paint 485 2 Finish 473-73 JACK TAR Vinyl Anti-fouling Paint 485 2 Total Dry Mils 20 Note: Adding a third coat of anti-fouling paint to the break of the bow and to the rudder/prop wash area will extend the service life of an anti-fouling system. 02.B JackTar Phenolic / JackTar Cold Plastic Antifouling System Offers excellent protection and durability for sailboats and slower moving vessels. This system consists of a phenolic anti-corrosive primer and a cuprous oxide anti-fouling paint. Coat Product Description Sq.Ft Mils Prime 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Finish 473-71 JACK TAR Cold Plastic Anti-fouling Paint 537 2 Finish 473-71 JACK TAR Cold Plastic Anti-fouling Paint 537 2 Total Dry Mils 13 Note: Adding a third coat of anti-fouling paint to the break of the bow and to the rudder/prop wash area will extend the service life of an anti-fouling system. Marine Coating Systems 8

Part III Coating Systems for Ships and Boats Section 02 STEEL VESSELS - EXTERIOR - BELOW WATER LINE (continued): 02.C JackTar Phenolic / JackTar Dub-L-Cop Antifouling System Offers good, economical protection for shrimp boats and other slow moving steel hull vessels. This system consists of a phenolic anticorrosive primer and a modified rosin based cuprous oxide anti-fouling paint. Coat Product Description Sq.Ft Mils Prime 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Finish 473-74 JACK TAR Dub-L-Cop Bottom Paint 568 2 Finish 473-74 JACK TAR Dub-L-Cop Bottom Paint 568 2 Total Dry Mils 13 Note: Adding a third coat of anti-fouling paint to the break of the bow and to the rudder/prop wash area will extend the service life of an anti-fouling system. Marine Coating Systems 9

Part III Coating Systems for Ships and Boats Section 03 STEEL VESSELS - EXTERIOR - DECKS & LADDERS Surface Preparation: is minimum acceptable. Near White Metal Sandblast (SSPC-SP10) is preferred and Commercial Sandblast (SSPC-SP6) 03.A MoPoxY TM ZR / MoPoxY TM HS / MoPoxY TM AR-200 Deck Armor High Build System For maximum service life, superior impact and abrasion resistance. Designed specifically for cargo and work deckson shrimp boats, supply boats, crew boats, drydocks, etc or any steel deck requiring exceptional long term protection. Coat Product Description Sq.Ft Mils Prime * 40-CM-4 MoPoxY TM ZR Zinc Rich Epoxy 257 3.5 Finish 41-BW-1 MoPoxY TM Deck Armor AR-100 26 60 Total Dry Mils 63.0 63.5 * Alternate Primer 613-10 MoPoxY TM HS High Solids Epoxy Primer 382 3 03.B MoPoxY TM ZR / MoPoxY TM HS / MoPoxY TM NS-200 Deck Armor High Build Non-Skid System For maximum service life, superior impact and abrasion resistance. Same protection and properties as the above system, except in a non-skid formulation. Coat Product Description Sq.Ft Mils Prime * 40-CM-4 MoPoxY TM ZR Zinc Rich Epoxy 257 3.5 Finish 41-BH-12 MoPoxY TM Deck Armor NS-200 24 60 Total Dry Mils 63.0 63.5 * Alternate Primer 613-10 MoPoxY TM HS High Solids Epoxy Primer 382 3 03.C MoPoxY TM ZR / MoPoxY TM HS Epoxy System A high performance deck coating system providing long term protection in marine environments. Coat Product Description Sq.Ft Mils Prime * 40-CM-4 MoPoxY TM ZR Zinc Rich Epoxy 257 3.5 Finish 613-series MoPoxY TM HS High Solids Epoxy Finish 374 3 Finish 613-series MoPoxY TM HS High Solids Epoxy Finish (NOTE) 374 3 Total Dry Mils 9 9.5 * Alternate Primer 613-10 MoPoxY TM HS High Solids Epoxy Primer 382 3 NOTE: Add JACK TAR Non-Skid Deck Compound, 492-3 to the final finish coat for use in critical work and traffic areas. Marine Coating Systems 10

Part III Coating Systems for Ships and Boats Section 04 STEEL VESSELS - INTERIOR - BULKHEAD & OVERHEAD Surface Preparation: Commercial Sandblast (SSPC-SP6) is preferred. Power Tool Clean (SSPC-SP3) or Hand Tool Clean (SSPC-SP2) are minimum acceptable. 04.A MoPoxY TM HS Epoxy System Combines excellent protection, maximum resistance to soiling and ease of cleaning. Coat Product Description Sq.Ft Mils Prime 613-10 MoPoxY TM HS Primer 382 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Total Dry Mils 9 04.B Rus-Kil Rust Inhibitive Enamel System Good resistance to soiling and easy maintenance Coat Product Description Sq.Ft Mils Prime 10-10 RUS-KIL Metal Primer 337 2 Finish 10-line RUS-KIL Enamel 417 1.5 Finish 10-line RUS-KIL Enamel 417 1.5 Total Dry Mils 5 Marine Coating Systems 11

Part III Coating Systems for Ships and Boats Section 05 STEEL VESSELS - INTERIOR - DECKS, LADDERS & PASSAGEWAYS Surface Preparation: Commercial Sandblast (SSPC-SP6) is preferred. Power Tool Clean (SSPC-SP3) or Hand Tool Clean (SSPC-SP2) are minimum acceptable. 05.A MoPoxY TM HS Epoxy System Combines excellent protection, maximum resistance to soiling and ease of cleaning. Coat Product Description Sq.Ft Mils Prime 613-10 MoPoxY TM HS Primer 382 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Total Dry Mils 9 05.B Rus-Kil / JackTar Alkyd Enamel System Good resistance to soiling and easy maintenance Coat Product Description Sq.Ft Mils Prime 10-10 RUS-KIL Metal Primer 337 2 Finish 450-line JACK TAR Yacht Deck Enamel 420 1.5 Finish 450-line JACK TAR Yacht Deck Enamel (NOTE) 420 1.5 Total Dry Mils 5 NOTE: Add JACK TAR Non-Skid Deck Compound, 492-3 to the final finish coat for use in critical work and traffic areas. Marine Coating Systems 12

Part III Coating Systems for Ships and Boats Section 06 FIBERGLASS VESSELS - EXTERIOR - ABOVE WATER LINE Surface Preparation: Wet sand with a 50:50 solution of Al-Co-Sol, 75-41 and water to remove all traces of wax, mold release compounds, etc.. Wipe clean with clean rags saturated with same solution. Immediately (within 1 hour) before applying coating directly to fiberglass, wipe down fiberglass with MoPoxY TM Thinner, 75-35, or MOTHANE TM Thinner, 43-EF-70, or BLP Vinyl Thinner, 475-31. Use only clean cotton rags for cleaning and fiberglass preparation. 06.A MoPoxY TM Plus / MOTHANE TM Polyurethane System Combines excellent chemical, solvent and abrasion resistance with superior gloss and color retention for maximum service. Coat Product Description Sq.Ft Mils Prime 41-CW-1 MoPoxY TM Plus Epoxy Coating 131 8 Finish * 72-series MOTHANE TM Polyurethane Coating 339 2 Finish * 72-series MOTHANE TM Polyurethane Coating 339 2 * Alternate Finish 72-series MOTHANE TM HD Polyurethane Coating 268 2.5 * Alternate Finish 72-series MOTHANE TM HS-1000 Polyurethane Coating 513 2 * Alternate Finish 72-series MOTHANE TM HS-900 Polyurethane Coating 428 2.5 Total Dry Mils 12-13 06.B JackTar Silicone Alkyd System Combines easier application with good resistance properties and excellent color and gloss retention. Coat Product Description Sq.Ft Mils Prime 432-line JACK TAR Silicone Yacht Finish 484 1.5 Finish 432-line JACK TAR Silicone Yacht Finish 484 1.5 Total Dry Mils 3.0 06.C JackTar Alkyd Enamel System Economic protection in mild marine service. Good color and gloss retention. Coat Product Description Sq.Ft Mils Prime 450-line JACK TAR Yacht Deck Enamel 420 1.5 Finish 450-line JACK TAR Yacht Deck Enamel 420 1.5 Total Dry Mils 3.0 Marine Coating Systems 13

Part III Coating Systems for Ships and Boats Section 07 FIBERGLASS VESSELS - EXTERIOR - BELOW WATER LINE Surface Preparation: Wet sand with a 50:50 solution of Al-Co-Sol, 75-41 and water to remove all traces of wax, mold release compounds, etc.. Wipe clean with clean rags saturated with same solution. Immediately (within 1 hour) before applying coating directly to fiberglass, wipe down fiberglass with MoPoxY TM Thinner, 75-35, or MOTHANE TM Thinner, 43-EF-70, or BLP Vinyl Thinner, 475-31. Use only clean cotton rags for cleaning and fiberglass preparation. 07.A MoPoxY TM Plus / JackTar Vinyl Antifouling System Offers maximum durability for fiberglass vessels. This system consists of one coat of high solids, high build epoxy primer and two coats of cuprous oxide, vinyl copolymer, anti-fouling paint. Coat Product Description Sq.Ft Mils Prime 41-CW-1 MoPoxY TM Plus Epoxy Coating 131 8 Finish 473-73 JACK TAR Vinyl Anti-fouling Paint 485 2 Finish 473-73 JACK TAR Vinyl Anti-fouling Paint 485 2 Total Dry Mils 12 Note: Adding a third coat of anti-fouling paint to the break of the bow and to the rudder/prop wash area will extend the service life of an anti-fouling system. 07.B JackTar Phenolic / JackTar Cold Plastic Antifouling System Offers excellent protection and durability for sailboats and slower moving vessels. This system consists of a phenolic anti-corrosive primer and a cuprous oxide anti-fouling paint. Coat Product Description Sq.Ft Mils Prime 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Finish 473-71 JACK TAR Cold Plastic Anti-fouling Paint 537 2 Finish 473-71 JACK TAR Cold Plastic Anti-fouling Paint 537 2 Total Dry Mils 10 Note: Adding a third coat of anti-fouling paint to the break of the bow and to the rudder/prop wash area will extend the service life of an anti-fouling system. Marine Coating Systems 14

Part III Coating Systems for Ships and Boats Section 07 FIBERGLASS VESSELS - EXTERIOR - BELOW WATER LINE (continued): 07.C JackTar Phenolic / JackTar Dub-L-Cop Antifouling System Offers good, economical protection for shrimp boats and other slow moving fiberglass hull vessels. This system consists of a phenolic anti-corrosive primer and a modified rosin based cuprous oxide anti-fouling paint. Coat Product Description Sq.Ft Mils Prime 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Finish 473-74 JACK TAR Dub-L-Cop Bottom Paint 568 2 Finish 473-74 JACK TAR Dub-L-Cop Bottom Paint 568 2 Total Dry Mils 10 Note: Adding a third coat of anti-fouling paint to the break of the bow and to the rudder/prop wash area will extend the service life of an anti-fouling system. Marine Coating Systems 15

Part III Coating Systems for Ships and Boats Section 08 FIBERGLASS VESSELS - EXTERIOR - DECKS & LADDERS Surface Preparation: Wet sand with a 50:50 solution of Al-Co-Sol, 75-41 and water to remove all traces of wax, mold release compounds, etc.. Wipe clean with clean rags saturated with same solution. Immediately (within 1 hour) before applying coating directly to fiberglass, wipe down fiberglass with MoPoxY TM Thinner, 75-35, or MOTHANE TM Thinner, 43-EF-70, or BLP Vinyl Thinner, 475-31. Use only clean cotton rags for cleaning and fiberglass preparation. 08.A MoPoxY TM HS / MoPoxY TM AR-200 Deck Armor High Build System For maximum service life, superior impact and abrasion resistance. Designed specifically for any fiberglass deck requiring exceptional long term protection. Coat Product Description Sq.Ft Mils Prime 613-10 MoPoxY TM HS High Solids Epoxy Primer 382 3 Finish 41-BW-1 MoPoxY TM Deck Armor AR-100 26 60 Total Dry Mils 63 08.B MoPoxY TM HS / MoPoxY TM NS-200 Deck Armor High Build Non-Skid System For maximum service life, superior impact and abrasion resistance. Same protection and properties as the above system, except in a non-skid formulation. Coat Product Description Sq.Ft Mils Prime 613-10 MoPoxY TM HS High Solids Epoxy Primer 382 3 Finish 41-BH-12 MoPoxY TM Deck Armor NS-200 24 60 Total Dry Mils 63 08.C MoPoxY TM HS Epoxy System A high performance deck coating system providing long term protection in marine environments. Coat Product Description Sq.Ft Mils Prime 613-10 MoPoxY TM HS High Solids Epoxy Primer 382 3 Finish 613-series MoPoxY TM HS High Solids Epoxy Finish 374 3 Finish 613-series MoPoxY TM HS High Solids Epoxy Finish (NOTE) 374 3 Total Dry Mils 9 NOTE: Add JACK TAR Non-Skid Deck Compound, 492-3 to the final finish coat for use in critical work and traffic areas. Marine Coating Systems 16

Part III Coating Systems for Ships and Boats Section 09 FIBERGLASS VESSELS - INTERIOR - BULKHEAD & OVERHEAD Surface Preparation: Wet sand with a 50:50 solution of Al-Co-Sol, 75-41 and water to remove all traces of wax, mold release compounds, etc.. Wipe clean with clean rags saturated with same solution. Immediately (within 1 hour) before applying coating directly to fiberglass, wipe down fiberglass with MoPoxY TM Thinner, 75-35, or MOTHANE TM Thinner, 43-EF-70, or BLP Vinyl Thinner, 475-31. Use only clean cotton rags for cleaning and fiberglass preparation. 09.A MoPoxY TM HS Epoxy System Combines excellent protection, maximum resistance to soiling and ease of cleaning. Coat Product Description Sq.Ft Mils Prime 613-10 MoPoxY TM HS Primer 382 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Total Dry Mils 9 09.B Rus-Kil Rust Inhibitive Enamel System Good resistance to soiling and easy maintenance Coat Product Description Sq.Ft Mils Prime 10-10 RUS-KIL Metal Primer 337 2 Finish 10-line RUS-KIL Enamel 417 1.5 Finish 10-line RUS-KIL Enamel 417 1.5 Total Dry Mils 5 Marine Coating Systems 17

Part III Coating Systems for Ships and Boats Section 10 FIBERGLASS VESSELS - INTERIOR - DECKS, LADDERS & PASSAGEWAYS Surface Preparation: Wet sand with a 50:50 solution of Al-Co-Sol, 75-41 and water to remove all traces of wax, mold release compounds, etc.. Wipe clean with clean rags saturated with same solution. Immediately (within 1 hour) before applying coating directly to fiberglass, wipe down fiberglass with MoPoxY TM Thinner, 75-35, or MOTHANE TM Thinner, 43-EF-70, or BLP Vinyl Thinner, 475-31. Use only clean cotton rags for cleaning and fiberglass preparation. 10.A MoPoxY TM HS Epoxy System Combines excellent protection, maximum resistance to soiling and ease of cleaning. Coat Product Description Sq.Ft Mils Prime 613-10 MoPoxY TM HS Primer 382 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Total Dry Mils 9 10.B Rus-Kil Rust Inhibitive Enamel System Good resistance to soiling and easy maintenance Coat Product Description Sq.Ft Mils Prime 10-10 RUS-KIL Metal Primer 337 2 Finish 450-line JACK TAR Yacht Deck Enamel 420 1.5 Finish 450-line JACK TAR Yacht Deck Enamel (NOTE) 420 1.5 Total Dry Mils 5 NOTE: Add JACK TAR Non-Skid Deck Compound, 492-3 to the final finish coat for use in critical work and traffic areas. Marine Coating Systems 18

Part III Coating Systems for Ships and Boats Section 11 WOODEN VESSELS - EXTERIOR -ABOVE WATER LINE Surface Preparation: New wood should be sanded with fine garnet paper. Previously painted wood should be thoroughly cleaned and washed, then sanded with medium-fine garnet paper to remove all gloss. Feather-edge old paint around bare areas and spot prime as below. If old paint is in poor condition, remove completely and treat as new wood. 11.A MoPoxY TM Plus / MOTHANE TM Polyurethane System Combines excellent chemical, solvent and abrasion resistance with superior gloss and color retention for maximum service. Coat Product Description Sq.Ft Mils Prime 41-CW-1 MoPoxY TM Plus Epoxy Coating 131 8 Finish * 72-series MOTHANE TM Polyurethane Coating 339 2 Finish * 72-series MOTHANE TM Polyurethane Coating 339 2 * Alternate Finish 72-series MOTHANE TM HD Polyurethane Coating 268 2.5 * Alternate Finish 72-series MOTHANE TM HS-1000 Polyurethane Coating 513 2 * Alternate Finish 72-series MOTHANE TM HS-900 Polyurethane Coating 428 2.5 Total Dry Mils 12-13 11.B JackTar Silicone Alkyd System Combines easier application with good resistance properties and excellent color and gloss retention. Coat Product Description Sq.Ft Mils Prime 432-line JACK TAR Silicone Yacht Finish (thinned 10%) 484 1.5 Finish 432-line JACK TAR Silicone Yacht Finish 484 1.5 Finish 432-line JACK TAR Silicone Yacht Finish 484 1.5 Total Dry Mils 4.5 11.C JackTar Alkyd Enamel System Economic protection in mild marine service. Good color and gloss retention. Coat Product Description Sq.Ft Mils Prime 450-line JACK TAR Yacht Deck Enamel (thinned 10%) 420 1.5 Finish 450-line JACK TAR Yacht Deck Enamel 420 1.5 Finish 450-line JACK TAR Yacht Deck Enamel 420 1.5 Total Dry Mils 4.5 Marine Coating Systems 19

Part III Coating Systems for Ships and Boats Section 12 WOODEN VESSELS - EXTERIOR - BELOW WATER LINE Surface Preparation: Pressure wash with clean water to remove any surface contaminants. Allow to dry completely and sand to remove all coatings. Surface to be painted must be bare wood which is sound, clean and thoroughly dry prior to painting. 12.A MoPoxY TM Plus / JackTar Vinyl Antifouling System Offers maximum durability for wooden vessels. This system consists of one coat of high solids, high build epoxy primer and two coats of cuprous oxide, vinyl copolymer, anti-fouling paint. Coat Product Description Sq.Ft Mils Prime 41-CW-1 MoPoxY TM Plus Epoxy Coating 131 8 Finish 473-73 JACK TAR Vinyl Anti-fouling Paint 485 2 Finish 473-73 JACK TAR Vinyl Anti-fouling Paint 485 2 Total Dry Mils 12 Note: Adding a third coat of anti-fouling paint to the break of the bow and to the rudder/prop wash area will extend the service life of an anti-fouling system. 12.B JackTar Phenolic / JackTar Cold Plastic Antifouling System Offers excellent protection and durability for sailboats and slower moving vessels. This system consists of a phenolic anti-corrosive primer and a cuprous oxide anti-fouling paint. Coat Product Description Sq.Ft Mils Prime 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Finish 473-71 JACK TAR Cold Plastic Anti-fouling Paint 537 2 Finish 473-71 JACK TAR Cold Plastic Anti-fouling Paint 537 2 Total Dry Mils 13 Note: Adding a third coat of anti-fouling paint to the break of the bow and to the rudder/prop wash area will extend the service life of an anti-fouling system. Marine Coating Systems 20

Part III Coating Systems for Ships and Boats Section 12 WOODEN VESSELS - EXTERIOR - BELOW WATER LINE 12.C JackTar Phenolic / JackTar Dub-L-Cop Antifouling System Offers good, economical protection for shrimp boats and other slow moving wooden hull vessels. This system consists of a phenolic anti-corrosive primer and a modified rosin based cuprous oxide anti-fouling paint. Coat Product Description Sq.Ft Mils Prime 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Intermediate 409-68 JACK TAR Phenolic Anti-corrosive Primer 310 3 Finish 473-74 JACK TAR Dub-L-Cop Bottom Paint 568 2 Finish 473-74 JACK TAR Dub-L-Cop Bottom Paint 568 2 Total Dry Mils 13 Note: Adding a third coat of anti-fouling paint to the break of the bow and to the rudder/prop wash area will extend the service life of an anti-fouling system. Marine Coating Systems 21

Part III Coating Systems for Ships and Boats Section 13 WOODEN VESSELS - EXTERIOR - DECKS & LADDERS Surface Preparation:. New wood should be sanded with fine garnet paper. Previously painted wood should be thoroughly cleaned and washed, then sanded with medium-fine garnet paper to remove all gloss. Feather-edge old paint around bare areas and spot prime as below. If old paint is in poor condition, remove completely and treat as new wood. * NOTE: Primer should be thinned 15-20% on bare wood surfaces. 13.A MoPoxY TM HS / MoPoxY TM AR-200 Deck Armor High Build System For maximum service life, superior impact and abrasion resistance. Designed specifically for any deck requiring exceptional long term protection. Coat Product Description Sq.Ft Mils Prime * 613-10 MoPoxY TM HS High Solids Epoxy Primer 382 3 Finish 41-BW-1 MoPoxY TM Deck Armor AR-100 26 60 Total Dry Mils 63 13.B MoPoxY TM HS / MoPoxY TM NS-200 Deck Armor High Build Non-Skid System For maximum service life, superior impact and abrasion resistance. Same protection and properties as the above system, except in a non-skid formulation. Coat Product Description Sq.Ft Mils Prime * 613-10 MoPoxY TM HS High Solids Epoxy Primer 382 3 Finish 41-BH-12 MoPoxY TM Deck Armor NS-200 24 60 Total Dry Mils 63 13.C MoPoxY TM HS Epoxy System A high performance deck coating system providing long term protection in marine environments. Coat Product Description Sq.Ft Mils Prime * 613-10 MoPoxY TM HS High Solids Epoxy Primer 382 3 Finish 613-series MoPoxY TM HS High Solids Epoxy Finish 374 3 Finish 613-series MoPoxY TM HS High Solids Epoxy Finish (NOTE) 374 3 Total Dry Mils 9 NOTE: Add JACK TAR Non-Skid Deck Compound, 492-3 to the final finish coat for use in critical work and traffic areas. Marine Coating Systems 22

Part III Coating Systems for Ships and Boats Section 14 WOODEN VESSELS - INTERIOR - BULKHEAD & OVERHEAD Surface Preparation:. New wood should be sanded with fine garnet paper. Previously painted wood should be thoroughly cleaned and washed, then sanded with medium-fine garnet paper to remove all gloss. Feather-edge old paint around bare areas and spot prime as below. If old paint is in poor condition, remove completely and treat as new wood. * NOTE: Primer should be thinned 15-20% on bare wood surfaces. 14.A MoPoxY TM HS Epoxy System Combines excellent protection, maximum resistance to soiling and ease of cleaning. Coat Product Description Sq.Ft Mils Prime 613-10 MoPoxY TM HS Primer 382 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Total Dry Mils 9 14.B Rus-Kil Rust Inhibitive Enamel System Good resistance to soiling and easy maintenance Coat Product Description Sq.Ft Mils Prime 10-10 RUS-KIL Metal Primer 337 2 Finish 10-line RUS-KIL Enamel 417 1.5 Finish 10-line RUS-KIL Enamel 417 1.5 Total Dry Mils 5 Marine Coating Systems 23

Part III Coating Systems for Ships and Boats Section 15 WOODEN VESSELS - INTERIOR - DECKS, LADDERS & PASSAGEWAYS Surface Preparation:. New wood should be sanded with fine garnet paper. Previously painted wood should be thoroughly cleaned and washed, then sanded with medium-fine garnet paper to remove all gloss. Feather-edge old paint around bare areas and spot prime as below. If old paint is in poor condition, remove completely and treat as new wood. * NOTE: Primer should be thinned 15-20% on bare wood surfaces. 15.A MoPoxY TM HS Epoxy System Combines excellent protection, maximum resistance to soiling and ease of cleaning. Coat Product Description Sq.Ft Mils Prime * 613-10 MoPoxY TM HS Primer 382 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Finish 613-line MoPoxY TM HS Epoxy (NOTE) 374 3 Total Dry Mils 9 NOTE: Add JACK TAR Non-Skid Deck Compound, 492-3 to the final finish coat for use in critical work and traffic areas. 15.B Rus-Kil Rust Inhibitive Enamel System Good resistance to soiling and easy maintenance Coat Product Description Sq.Ft Mils Prime * 10-10 RUS-KIL Metal Primer 337 2 Finish 450-line JACK TAR Yacht Deck Enamel 420 1.5 Finish 450-line JACK TAR Yacht Deck Enamel (NOTE) 420 1.5 Total Dry Mils 5 NOTE: Add JACK TAR Non-Skid Deck Compound, 492-3 to the final finish coat for use in critical work and traffic areas. Marine Coating Systems 24

Part III Coating Systems for Ships and Boats Section 16 ENGINE ROOM - BULKHEAD, OVERHEAD & DECKS Surface Preparation: Steel - Commercial Sandblast (SSPC-SP6) is preferred. Power Tool Clean (SSPC-SP3) or Hand Tool Clean (SSPC-SP2) are minimum acceptable. Fiberglass - Wet sand with a 50:50 solution of Al-Co-Sol, 75-41 and water to remove all traces of wax, mold release compounds, etc.. Wipe clean with clean rags saturated with same solution. Immediately (within 1 hour) before applying coating directly to fiberglass, wipe down fiberglass with MoPoxY TM Thinner, 75-35, or MOTHANE TM Thinner, 43-EF-70, or BLP Vinyl Thinner, 475-31. Use only clean cotton rags for cleaning and fiberglass preparation. Wood - New wood should be sanded with fine garnet paper. Previously painted wood should be thoroughly cleaned and washed, then sanded with medium-fine garnet paper to remove all gloss. Feather-edge old paint around bare areas and spot prime as below. If old paint is in poor condition, remove completely and treat as new wood. * NOTE: Primer should be thinned 15-20% on bare wood surfaces. 16.A MoPoxY TM HS Epoxy System Combines excellent protection, maximum resistance to soiling and ease of cleaning. Coat Product Description Sq.Ft Mils Prime 613-10 MoPoxY TM HS Primer 382 3 Finish 613-line MoPoxY TM HS Epoxy 374 3 Finish 613-line MoPoxY TM HS Epoxy (NOTE) 374 3 Total Dry Mils 9 NOTE: Add JACK TAR Non-Skid Deck Compound, 492-3 to the final finish coat for use on decks in work and traffic areas. 16.B Rus-Kil Rust Inhibitive Enamel System Good resistance to soiling and easy maintenance Coat Product Description Sq.Ft Mils Prime 10-10 RUS-KIL Metal Primer 337 2 Finish 10-line RUS-KIL Enamel 417 1.5 Finish 10-line RUS-KIL Enamel (NOTE) 417 1.5 Total Dry Mils 5 NOTE: Add JACK TAR Non-Skid Deck Compound, 492-3 to the final finish coat for use on decks in work and traffic areas. Marine Coating Systems 25

Part III Coating Systems for Ships and Boats Section 17 POTABLE WATER TANKS Surface Preparation: Steel - White Metal Sandblast (SSPC-SP5) is required. Fiberglass - Wet sand with a 50:50 solution of Al-Co-Sol, 75-41 and water to remove all traces of wax, mold release compounds, etc.. Wipe clean with clean rags saturated with same solution. Immediately (within 1 hour) before applying coating directly to fiberglass, wipe down fiberglass with MoPoxY TM Thinner, 75-35, or MOTHANE TM Thinner, 43-EF-70, or BLP Vinyl Thinner, 475-31. Use only clean cotton rags for cleaning and fiberglass preparation. 17.A MoPoxY TM HS-50 NSF Epoxy System Approved by National Sanitation Foundation (NSF), Standard 61, for contact with potable water Coat Product Description Sq.Ft Mils Prime 40-BH-11 MoPoxY TM HS-50 NSF Epoxy 134 6 Finish 40-BW-5 MoPoxY TM HS-50 NSF Epoxy 134 6 Total Dry Mils 12 Provide adequate ventilation during application, continuing ventilation during entire cure cycle. Allow the system to cure a minimum of 7 days (at 75 F minimum) after application of the finish coat. Perform a fresh water rinse after cure cycle and prior to placing into service. Section 18 FUEL TANKS (INCLUDING COMPENSTATED FUEL TANKS) Surface Preparation: Steel - White Metal Sandblast (SSPC-SP5) is required. 18.A MoPoxY TM Mastic Epoxy System Coat Product Description Sq.Ft Mils Prime 40-AH-51 MoPoxY TM Mastic Epoxy 217 6 Finish 40-AW-32 MoPoxY TM Mastic Epoxy 217 6 Total Dry Mils 12 Provide adequate ventilation during application, continuing ventilation during entire cure cycle. Allow the system to cure a minimum of 7 days (at 75 F minimum) after application of the finish coat. Marine Coating Systems 26

Part III Coating Systems for Ships and Boats Section 19 BILGES & VOIDS Surface Preparation: Steel - Commercial Sandblast (SSPC-SP6) is preferred. Power Tool Clean (SSPC-SP3) or Hand Tool Clean (SSPC-SP2) are minimum acceptable. Fiberglass - Wet sand with a 50:50 solution of Al-Co-Sol, 75-41 and water to remove all traces of wax, mold release compounds, etc.. Wipe clean with clean rags saturated with same solution. Immediately (within 1 hour) before applying coating directly to fiberglass, wipe down fiberglass with MoPoxY TM Thinner, 75-35, or MOTHANE TM Thinner, 43-EF-70, or BLP Vinyl Thinner, 475-31. Use only clean cotton rags for cleaning and fiberglass preparation. Wood - New wood should be sanded with fine garnet paper. Previously painted wood should be thoroughly cleaned and washed, then sanded with medium-fine garnet paper to remove all gloss. Feather-edge old paint around bare areas and spot prime as below. If old paint is in poor condition, remove completely and treat as new wood. Primer should be thinned 15-20% on bare wood surfaces. 19.A MoPoxY TM Plus Epoxy System Combines maximum protection with minimum maintenance. Coat Product Description Sq.Ft Mils Prime 41-CW-1 MoPoxY TM Plus 131 8 Finish 41-CW-1 MoPoxY TM Plus 131 8 Total Dry Mils 16 Provide adequate ventilation during application, continuing ventilation during entire cure cycle. Allow the system to cure a minimum of 7 days (at 75 F minimum) after application of the finish coat. Marine Coating Systems 27

PAINTING SYSTEMS GUIDE INDEX OF PRODUCT DATA SHEETS 330 Line ACR-A-LAC TM 100% Acrylic Gloss Enamel 330-7 ACR-A-LAC TM 100% Acrylic Metal Primer Red 260-45 ARCHITECTURAL TM Latex Block Filler 60-7 BLOC-FIL TM Latex Block Filler 19-10 BLOC-SEAL TM Block Fill Base 1335 Line COVENTRY 100% Acrylic Latex Semi-Gloss Enamel 2335 Line COVENTRY Acrylic Eggshell Enamel 19-8 COVENTRY Wood Sealer, White 319-8 COVENTRY Latex Enamel Undercoat 335 Line COVENTRY Latex High Gloss Enamel 35 Line COVENTRY Latex Flat Wall Paint 135 Line COVENTRY LUSTARITE Alkyd Satin Enamel 19-7 COVENTRY Prymall 2 Q.D. Primer & Sealer 74-12 DUB-L-TITE TM Silicone Waterproofing, Clear 43-25 ELASTOMERIC ROOF COATING Reflective White 43-20 ELASTOMERIC WALL COAT, White 19-8 ENAMEL UNDERCOAT and Wood Sealer: see also COVENTRY 70-41 FLO-TEC TM Phenolic Heavy Duty Gym Floor Finish 55-DW-3 FOG DRY ACRYILIC COATING, Flat White 55-AW9 FOG DRY ACRYILIC COATING, Gloss White 6-DW-58 FOG DRY ALKYD FLAT COATING, White 61-BW-2 FOG DRY ALKYD GLOSS COATING, White 61-AW-6 FOG DRY ALKYD SEMI-GLOSS COATING, White 9-5 GALVA-TEC TM 100% Acrylic Galvanized Primer 80166 GALVANIZING REPAIR COATING DOD-P-21035A 1

PAINTING SYSTEMS GUIDE INDEX OF PRODUCT DATA SHEETS 308-Line H 2 O Concrete Stain 100% Acrylic 310-Line H 2 O RUS-KIL Acrylic DTM Rust Resistant Coating 310-Line H 2 O RUS-KIL Acrylic DTM Rust Resistant Primers 350-Line H 2 O Floor & Patio Satin Finish!00% Acrylic Polyurethane 62-AY-5 HEAT RESISTANT ALUMINUM, Silicone Acrylic 11-61 HEAT RESISTANT ALUMINUM, Silicone Alkyd 62-AY-1 HIGH HEAT RESISTANT ALUMINUM, Silicone 28-DR-147 HIGH SOLIDS PRIMER, Red Oxide 470-31 JACK TAR 100% Phenolic Marine Spar Varinsh 470-34 JACK TAR Marine Spar Varnish w/ Ultraviolet Filter 492-3 JACK TAR Non-Skid Deck Compound 432 Line JACK TAR Silicone Yacht Finish 9835-165 LACQUER Sanding Sealer 9835-172 LACQUER SS Hi Build White 9835-Line LACQUER Tint Bases 9835-098 LACQUER, Clear, WW Gloss 9835-100 LACQUER, Clear, WW Satin LUSTARITE : See COVENTRY LUSTARITE 40-CM-1 40-AW-42 28-DR-160 40-AX-7 40-BX-6 28-DH-50 41-Series 40-AF-10 41-BW-1 41-BH-12 41-AH-2 MARE ISLAND EPOXIES: See MIL-P-24441 MIL-P-24441 F 150 Type IV Green Primer MIL-P-24441 F 152 Type IV White MO-BAR TM PM-III Universal Primer, Red (Gray 29DH093) MO-TAR TM C-200 Epoxy Coating, Black MO-TAR TM HB 90 Epoxy Coating MO-ZINC TM 3 Inorganic Zinc Rich Primer MOPACOTE : See WEATHER-TITE TM MOPOX-ACRYL TM Acrylic Epoxy Coating MoPoxY TM Clear Base - see 513 line for data MoPoxY TM DECK ARMOR AR-100 MoPoxY TM DECK ARMOR NS-200, Non-skid MoPoxY TM GF Glass Flake Phenolic Epoxy Coating, Gray 2

PAINTING SYSTEMS GUIDE INDEX OF PRODUCT DATA SHEETS 69-AW-5 MoPoxY TM H2O-100 Waterborne Epoxy Acrylic, White 69-DR-1 MoPoxY TM H2O-200 Waterborne Epoxy Metal Primer 69-AW-6 MoPoxY TM H2O-200 Waterborne Polyadide Epoxy Coating, White 40-DR-5 MoPoxY TM HB High Build Metal Primer 40-BW-5 MoPoxY TM HS-50 NSF Epoxy Coating (For Potable Water) 41-CW-2 MoPoxY TM HS-60 NSF Epoxy Coating (For Potable Water) 613 Line MoPoxY TM HS High Solids Epoxy Coating 613-10 MoPoxY TM HS High Solids Epoxy Metal Primer 40-CM-11 MoPoxY TM HZR Zinc Rich Epoxy Primer, Green 41-BK-14 MoPoxY TM IR High Solids Epoxy 40-AY-2 MoPoxY TM MASTIC Aluminum 40-AH-51 MoPoxY TM MASTIC Epoxy Coating, Gray 40-AW-32 MoPoxY TM MASTIC Epoxy Coating, White 41-AH-1 MoPoxY TM PH Phenolic Epoxy Coating, Gray 41-CH-1 MoPoxY TM PLUS High-Build Epoxy Coating 41-AF-2 MoPoxY TM PRE-PREP Rust Penetrating Sealer 41-DM-3 MoPoxY TM PRIME Zinc Preconstruction Primer, HAPS Free 41-DM-1 MoPoxY TM PRIME Zinc Preconstruction Primer\ 40-DR-12 MoPoxY TM PRIME Preconstruction Primer 41-DM-2 MoPoxY TM ZR HS Zinc Rich HAPS Free Primer 40-CM-4 MoPoxY TM ZR Zinc Rich Epoxy Primer, Green 72 Line MOTHANE TM HS-1000 Aliphatic Acrylic Polyurethane Enamel 30 Line NAM-A-LAC All Purpose Enamel 71 Line NUWOOD Penerating Wood Finish 72-35 NUWOOD Polyurethane Gloss Finish 72-36 NUWOOD Polyurethane Satin Finish 72-45 NUWOOD Tung Oil Clear Stain 19-7 PRYMALL 2 Q.D. Primer and Sealer: See also COVENTRY 310 Line RUS-KIL H20 Acrylic see H2O RUS-KIL 650 Line RUS-KIL HI-HIDE 650 Gloss Enamel 655 Line RUS-KIL HI-HIDE 655 Semi-Gloss Enamel 3

PAINTING SYSTEMS GUIDE INDEX OF PRODUCT DATA SHEETS 10 Line RUS-KIL Rust Inhibiting Coating 10 Line RUS-KIL Rust Inhibiting Primer (Red, Gray, White) 28-DR-79 SILICONE ALKYD High Heat Primer 206-10 SMOOTH-COTE Exterior 100% Acrylic House Paint Primer 296 Line SMOOTH-COTE Exterior Acrylic Flat House Paint 295 Line SMOOTH-COTE Exterior Acrylic Semi-Gloss House Paint 205-20 SMOOTH-COTE Exterior & Interior Primer (Oil) 205-22 SMOOTH-COTE Exterior Alkyd Oil Base House Paint 205-10 SMOOTH-COTE Exterior Oil Base House Paint Primer (Alkyd) 291 Line SMOOTH-COTE Exterior Vinyl Acrylic Flat House Paint 293-Line SMOOTH-COTE Interior Alkyd Semi-Gloss Enamel 292-Line SMOOTH-COTE Interior Latex Eggshell 289-Line SMOOTH-COTE Interior Latex Flat 219-19 SMOOTH-COTE Interior Latex Primer/Sealer 290-Line SMOOTH-COTE Interior Latex Semi-Gloss Enamel 9-78 SPEED PRIME Red Oxide Primer 28-DR-166 50-Line SPEED PRIMER HS High Solids Primer, Red SPEEDECK Floor & Deck Enamel SPRAY FOG DRY: see FOG DRY 9-42 VINYL WASH PRIMER 40 Line WEATHER-TITE TM 100% Acrylic Latex House Paint - Flat 140 Line WEATHER-TITE TM 100% Acrylic Latex House Paint - Gloss 240 Line WEATHER-TITE TM 100% Acrylic Latex House Paint - Satin 60-Series WEATHER-TITE TM 100 Premium Siliconized Acrylic Caulk 74-7 WEATHER-TITE TM Clear Waterproofing Sealer 5-20 WEATHER-TITE TM Southern White Gloss House Paint 5-6 WEATHER-TITE TM Southern White House Paint Primer 6-6 WEATHER-TITE TM Universal 100% Acrylic Latex Primer 7-10 WEATHER PROTECTOR Exterior Clear Sealer & Preservative 44 Line WEATHER PROTECTOR Interior/Exterior Acrylic Latex Stain 4