Product Information/Specifications

Transcription

1 DECK WASH No. 61 Ideal for the Maintenance Cleaning of Exterior Wood, Vinyl or Composite Decks, Porches, Fences & Siding. AVAILABLE IN: Quart Only No. 61 Clear No oz. NOT TINTABLE sq. ft. (46-56 m2) per quart. Biodegradable Anionic Surfactants Water. Recycle or dispose of container or unused product call CLEANUP (U.S.A. only) Airless Spray: Conventional Spray: Brush: Pump Sprayer:. Roller: PREPARATIONS Dampen grass, plants, & other vegetation with water. Wear old clothing, protective eyewear & rubber gloves. Remove tab, turn nozzle to WATER position and wet entire surface to be cleaned. Turn nozzle to ON and apply product liberally. Allow product to work for at least five minutes. Do not allow product to dry on the surface. Rinse thoroughly with water. Scrubbing may be required on severely stained surfaces. (Mildewed areas may require No. 62 Multi-Surface Cleaner & Mildew Stain Remover.) Copyright 2006 Behr Process Corporation Created 10/06

2 No. 62 Clear No oz. INT/EXT MULTI-SURFACE CLEANER & MILDEW STAIN REMOVER No (19-23 m 2) sq. ft. per gallon EXTERIOR Use on Exterior Mildewed Stained Surfaces of all types: Concrete, Masonry, Stucco, Stone, Brick, Vinyl, Composite, Tile, Plastic, Fiberglass and Roofing Materials. INTERIOR Use on Interior Mildew Stained Surfaces, Bathroom Areas and Woodwork. Sodium Hypochlorite 4% 6% <0 g/l Water. Recycle or dispose of unused product call CLEANUP (U.S.A. only) Airless Spray: Conventional Spray: Brush: Nylon/Polyester blend Pump Sprayer: High Quality Pump Sprayer with Adjustable tip. Roller: Exterior Surface: Shake thoroughly before use. Dampen grass, plants, and other vegetation with water and protect these areas adjacent surfaces with plastic. Rinse thoroughly with water immediately after use. Wear old clothing, goggles and rubber gloves. Protect clothing from contact with liquid. Test a small area, rinse and let dry before continuing. Apply using a Pump Sprayer. Wear appropriate respirator, eye and apparel protection when using a sprayer. Apply to a wet surface. Allow product to work for at least one minute to remove mildew stains. Rinse thoroughly. While mildew stain removal is immediate, lightening aged-weathered wood may take up to 15 minutes for full effect. Scrubbing may be required on severely stained surfaces. Prolonged exposure on painted surfaces may damage finish. Thoroughly rinse the surface with water and allow to dry. Interior Surface: Shake thoroughly before use. Product must be diluted with one part BEHR No. 62 Multi-Surface Deck-Prep Cleaner & Mildew Stain Remover to three parts water. Do Not Use Full Strength. Avoid contact with clothing, carpet and fabrics. Wear old clothing, goggles and rubber gloves. Protect clothing from contact with liquid. Apply using a clean cloth or sponge; spraying is not recommended for interior applications. Scrubbing may be required on severely stained surfaces. Prolonged exposure on painted surface may damage finish. Thoroughly rinse the surface with fresh water. Copyright Behr Process Corporation Revised 9/06

3 CLEANER, BRIGHTENER & CONDITIONER No. 63 Exterior wood & composite decks, siding, shakes, shingles, fences and furniture. Exterior vinyl and aluminum siding, masonry, stucco and cement. No. 63 Blue No oz. NOT TINTABLE 200 (19 m2) sq. ft. per gallon of mixed F & 50% humidity Oxalic Acid 7% 10% 0 gm/l Material (Includes Water) 7 gm/l Coating (Excludes Water) Soap & Water. Recycle or dispose of paint call CLEANUP (U.S.A. only) Preparation: Be sure to have the following: source for tap water, garden hose with nozzle, acid resistant rubber gloves, goggles, large plastic mixing container and protective plastic drop cloths. Use BEHR No. 62 Multi-Surface Cleaner & Mildew Stain Remover or bleach and water where mildew, algae or fungus stains are present. Dampen grass, plants, and other vegetation with water and protect these areas and adjacent surfaces with plastic. Rinse thoroughly with water immediately after use Airless Spray: Conventional Spray: Pump Sprayer: High Quality Sprayer with adjustable tip. Brush: Bristle Broom or Brush Roller: Shake product thoroughly. Be sure that the plastic mixing container is large enough to hold up to 5 gallons of diluted solution. Do not mix in metal container. Dilute one part BEHR No. 63 Cleaner Brightener & Conditioner with 4 parts tap water in a clean plastic container (DO NOT USE METAL). To remove rust, red clay stains and for extremely hard to clean weathered wood surfaces, use product full strength. Test solution in a small, hidden area before applying to see its effectiveness. Do not apply product if surface and air temperatures are below 50 F (10 C) or above 90 F (32 C). Lightly dampen surfaces with water prior to cleaning. Apply solution liberally with a plastic container pump sprayer, brush, mop or roller. Keep the surface wet for minutes. Reapply solution as needed to keep the surface wet. Scrub surface using a stiff bristle broom or brush. The solution will foam. After the minute cleaning period, rinse the surface thoroughly. Surfaces other than wood may be dulled if not rinsed off quickly. Copyright Behr Process Corporation Revised 9/06

4 15 MINUTE QUIK-FIX DECK REMOVER & WOOD RESURFACER No. 64 Exterior deteriorated latex or oil-based coatings on wood decks, siding, fences, shake and shingles. Ideal for removing loose wood fiber, unsightly stains caused by oil or rusty water on uncoated tile, concrete, masonry, stucco, stone and brick. For 100% Acrylic water-based products, use a conventional paint stripper. No. 64 Clear No oz sq. ft. per gallon Depending on porosity of the surface. Allow a minimum of 24 hours in warm, dry weather, longer in cooler temperatures of in higher humidity. Sodium Hydroxide 10% 13% Flush sprayer and all tools with fresh water. Recycle or dispose of paint call CLEANUP (U.S.A. only) PREPARATION: Stir or shake before use. Do not thin product. Be sure to have the following before application source for tap water, garden hose with nozzle, acid resistant rubber gloves, goggles, plastic sprayer or disposable brush, stiff bristle broom or brush, protective plastic drop cloths and No Minute Quik-Fix Deck Finish Remover & Wood Resurfacer. Do not apply in direct sunlight or on hot surfaces. Use when temperature is between F. Airless Spray: Conventional Spray: Brush: Nylon/Polyester blend Pump Sprayer: High Quality Pump Sprayer with Adjustable tip. Roller: Dampen grass, plants, and other vegetation with water and protect these areas and adjacent surfaces with plastic. Rinse thoroughly with water immediately after use Wear old clothing, goggles, and acid resistant rubber gloves. Protect clothing from contact with product. Test in a small area for effectiveness, rinse and let dry before continuing. Apply using a Pump Sprayer or disposable nylon polyester brush. Natural bristle brushes or lambs wool applicators are not recommended. Wear appropriate respirator, eye and apparel protection when using a sprayer. Do not allow product to dry; keep surface wet for about 15 minutes while the old finish begins to lift from the surface. Reapply as needed to keep the surface wet during the removal period. Most deteriorated finishes will start to lift after about minutes. When the finish starts to lift, lightly scrub the surface using a stiff bristle broom or brush. Rinse with water from garden hose using nozzle at maximum pressure. Pressure Washing should be left to the professional, as this may harm the wood. If some of the old finish remains on the surface, repeat application procedure. For mildew, use no. 62 Multi-Surface Cleaner & Mildew Stain Remover or bleach and water. See label for instructions. Use no. 63 Cleaner Brightener & Conditioner on all wood surfaces to rejuvenate natural wood color and neutralize the stripping action. This provides stability for reapplication of a new finish or sealer. Some woods may darken after stripping. Copyright Behr Process Corporation Revised 9/06

5 INTERIOR/EXTERIOR CONCRETE CLEANER & DEGREASER No. 990 Use on interior/exterior masonry surfaces such as garage floors, driveways, sidewalks, patios, walkways, porches, basement floors, steps, stepping stones and pool decks. Great on concrete, brick, stone, asphalt and exposed aggregate (concrete with pebbles) No. 990 No oz. 500 sq. ft. diluted at 4:1 and one gallon of full strength will cover 150 sq. F & 50% humidity Quaternary Amine Compound 14.2% 17% 0 gm/l Material (Includes Water) 3 gm/l Coating (Excludes Water). Recycle or dispose of container or unused product call CLEANUP (U.S.A. only) Mixing of Product Wear protective clothing; eye goggles and chemical resistant rubber gloves. Be sure the plastic mixing container is large enough to hold up to 2 gallons of diluted solution. Use BEHR Concrete Cleaner & Degreaser full strength for tough stains; 1:4 dilution (1 qt cleaner in 1 gal water) for general cleaning and 1:16 dilution (1 cup cleaner in 1 gal water) for cleaning previously painted surfaces. Stir diluted solution thoroughly. Avoid splashing. Airless Spray: Conventional Spray: Brush: Roller: Pump Sprayer: High Quality with an adjustable tip. Thinner: SURFACE PREPARATION Be sure to have the following before using BEHR S Concrete Cleaner & Degreaser And Concrete Etcher & Rust Remover: source for tap water, garden hose with a pressure nozzle, chemical resistant rubber gloves, eye goggles, large plastic mixing container, a plastic brush or broom, squeegee or mop and protective plastic drop cloths. Wear appropriate apparel, eye and skin protection when applying product. Wipe up all excess oil and grease spills. Scrape and sweep away dirt and loose contaminates on surface. Protect grass and any plant life by lightly dampening these areas with water; use plastic drop cloths to cover these and any other areas that might be accidentally splashed during the cleaning process. Failure to keep grass and plants dampened will result in damage to these areas. Use plastic drop cloths to cover and protect all areas not being cleaned. Wear protective clothing; eye goggles and chemical resistant rubber gloves. To ensure uniformity, lightly treat the entire area to be cleaned. Wet the surface first by spraying with a garden hose. Then apply the product (full strength for tough stains, diluted for general cleaning) and work into the surface with a plastic brush or broom. Copyright Behr Process Corporation Revised 6/07

6 INTERIOR/EXTERIOR CONCRETE ETCHER & RUST REMOVER No. 991 Use on Interior or Exterior exposed concrete, cement and cinder block surfaces such as garage floors, driveways, walkways, patios, pool decks, basement floors and basement walls. Do Not Use On Marble, Granite, Terrazzo, Colored Concrete or on brass, bronze or copper. No. 991 No oz sq. ft. (28-37m2) and one gallon of full strength product will etch and clean sq. ft. (14-18m2). Actual overage depends on porosity and severity of surface soil or F & 50% humidity Phosphoric Acid 31% 46%. 63gm/l Material (Includes Water) 166 gm/l Coating (Excludes Water). Recycle or dispose of container or unused product call CLEANUP (U.S.A. only) Mixing of Product Use large plastic container that is at least 2 gallons (8 L) for dilution. Do not mix or use in a metal container. Use one part product with one part water for areas. Use full strength on heavily stained exterior areas. Do Not Use Full Strength On Interior Surfaces and always work in a wellventilated areas. Stir diluted solution thoroughly. Avoid splashing. One gallon of diluted solution will etch and clean Airless Spray: Conventional Spray: Brush: Stiff Bristle Brush or Broom Pump Sprayer: High Quality with an adjustable tip. SURFACE PREPARATION Allow new concrete surfaces to cure approximately 30 days before etching. Use BEHR No. 990 Concrete Cleaner & Degreaser to remove dirt and grease. See product label for directions. Completely strip all coatings prior to use. On exterior surfaces use BEHR No Minute Quik-Fix. On interior surfaces or for 100% acrylic water-based products, use a conventional paint stripper. Be sure to rinse thoroughly before treating. Protect grass and any nearby plants by dampening these areas with water and covering with plastic drop cloths. Once the surface is ready for coating, use floor finishes such as BEHR Porch & Floor Enamel, BEHR 1- Part Epoxy Acrylic Concrete & Garage Floor Paint or BEHR Plus 10 Concrete Stain. Follow all label instructions. Use appropriate precautions (see warning). Avoid splashing. Spraying is not recommended. Keep area wet with water before and during the application of BEHR Concrete Etcher & Rust Remover. Work small areas at a time. On sloped surfaces, start at the lowest point working up to the highest point. Allow product to stand for 5-10 minutes then scrub with a stiff bristled, nonmetal brush or broom. Rinse surface thoroughly with fresh water while scrubbing. Do not let product dry on the surface. If product dries and a white powdery residue remains, it is critical to remove the residue by retreating with a diluted solution (1 part of product to 2 parts water) and scrubbing. Rinse thoroughly with water. Remove excess water with a non-metal squeegee or mop. Heavily stained areas or older stains may require additional applications. The surface is ready when it feels like fine to medium grit sandpaper and no residue or loose concrete remains on the surface. Copyright Behr Process Corporation Revised 6/07

7 CONCRETE & MASONRY PAINT STRIPPER NO. 992 Use on painted or stained Interior/Exterior Concrete, Masonry, Stone, Brick and Metal Surfaces such as: Garage Floors, Driveways, Walkways, Patios, Pool/Cool Decks, Basement Floors and Concrete Walls. Removes coatings such as: stains, epoxies, urethanes, elastomeric, alkyds, sealants, latex and most industrial and architectural paints. Do Not Use On Marble, Granite, Terrazzo, Colored Concrete, Brass, Bronze or Copper. No. 992 Spread rate is approximately sq. ft. per gallon. Penetration varies according to coating type, thickness and F & 50% humidity Surface dry time will vary, depending on air & surface temperature. Make sure surface is visually and completely dry to touch prior to recoating. CAUTION: Surfaces may become slippery when wet. Use caution when walking on surface when moisture is present. Glycol/Alcohol/Acid 8.0% 9.4% 8.52 lbs 40.6% WT. If product comes in contact with painted or finished surfaces, rinse immediately with fresh water. Thoroughly rinse all surfaces, clothing and tools with fresh water after use. Collect lifted coating and dispose of it in accordance with local government regulations. Contact your household refuse collection service for disposal of empty containers or unused product.. Airless Spray: Tip: Conventional Spray: Brush: Stiff Bristle Brush or Broom Pump Sprayer: SURFACE PREPARATION Shake Well Prior To Use. Pour the N Concrete & Masonry Paint Striper into a paint tray or bucket. If water seems to have separated out, stir product until uniform. For vertical and glossy or greasy surfaces, scuff sand the surface lightly with a medium grit sand paper prior to application to prevent sagging of paint stripper. Test Patch: A test area will indicate the time required to lift coating and the suitability of the product for the paint and substrate. Protect grass and any nearby plants by dampening these areas with water and covering with plastic drop cloths. Prevent all rinse solution from entering storm drains. Wear protective clothing, goggles, acid resistant gloves, and a NIOSH approved air purifying respirator with an organic vapor cartridge. Apply a thick, even layer of stripper onto the surface using a paintbrush or an airless sprayer. Stripper thickness should be such that the original coated surface is completely covered. Penetration varies according to coating type, thickness and temperature. Coating Will Wrinkle When The Job Is Done. Most coatings will take between 1 6 hours to lift. Check periodically during the waiting period, to ensure that the coating is completely covered with the stripper. If the coated surface becomes visible again, re-apply a light coating. The stripper should remain wet and active until the coating wrinkles. If hot or windy conditions cause drying, re-apply a light coating. Use a scraper, squeegee or pressure washer to remove all coating and residue. The stripper is formulated to remove several layers of coating in one application. Some areas however, may require an additional application to remove all layers. The stripped surface must be rinsed with water thoroughly to remove all chemical residues before recoating. Copyright 2008 Behr Process Corporation Created 7/08