OLYMPUS SYSTEM MICROSCOPE FOR METALLURGICAL USE scanned by J. G. McHone 6Novl I,= for personal use only, not for sale INSTRUCTION MANUAL MODEL I." a 'C. A
CONTENTS STANDARD EQUIPMENT................... 2 VARIOUS COMPONENTS OF THE MODEL BHM.......,... 3 ASSEMBLY........................ 4 IDENTIFICATION AND FUNCTION OF VARIOUS COMPONENTS..... 5 OPTICAL SYSTEM...................... 8 1. Objectives 2. Eyepieces....................... 9 3. Vertical Illuminator.................... 11 A. Aperture iris diaphragm................ 12 B. Field iris diaphragm LIGHT SOURCE STAGES......................... 13 1. Removal of Specimen Holder 2. Stage Spacer 3. Metal Slides Vlll. OBSERVATION TUBE.................... 14 1. lnterpupillary Distance and Diopter Adjustments 2. Light Path Selection IX. FOCUSING ADJUSTMENT................... 15 1. Tension Adjustment of Coarse Adjustment Knobs 2. Automatic Pre-focusing Lever 3. Stage Height Locking Lever TROUBLESHOOTING.................... 16
C I. STANDARD EQUIPMENT Component BHM Microscope stand with base BHM-F-2 Revolving nosepiece BH-R E o o o o Observation tubes Binocular tube, incl~ned 3' BH-B 13 Trinocular tube, inclined 3, w~th vertical photo tube BH-TR3 O O Vertical illuminator for brightfield 15-watt tungsten lamp house BH-MA BH-LHM Tungsten bulb, 6V 15W, 3 pcs. LS15 Square mechanical stage with right-hand low drive controls BH-SV Transformer TE-l I M5X, MIOX, MZOX, M4X (set of four) Ob~ectlves M Plan 5X, M Plan lox, M Plan 2X, M Plan 4X, M Plan 1X (oil) (set of five) Eyepieces High eyepoint BiWF lox, paired Photo eyepiece F K3.3X Metal slide plates (set of f~ve) l rnrnersion oil, bottled o Eyepiece caps (2 pcs.) Filter 32.5C Vinyl dust cover
II. VARIOUS COMPONENTS OF THE MODEL BHM The Oiympus System Microscope for reflected light Model BHM consists of a modular, building-block system of various components and interchangeable accessories, as shown below. A wide variety of combinations, standard or optional, is available according to your requirements. d Eyepiece ---.- Observation tube /C---- 15-watt tungsten Vertical illuminator -- Objective -- Stage -- --.-- Cord adapter
a Ill. ASSEMBLY The picture below illustrates the sequential procedure of assembly. The numbers indicate the order of assembly of various components. Remove dust caps before mounting components. Take care to keep all glass surfaces clean, and avoid scratching the glass surfaces. O Eyepiece caps a Observation tube 8 Tungsten bc~ tb % This unit should be attached on the microscope stand with the lamp house pointing away from the observer.
IV. IDENTI FlCATlON AND FUNCTION OF VARIOUS COMPONENTS Mechanical tube length adjustment rings Larnp house Rotate the rings to match the interpupillary distance setting obta~ned from the scale, and to correct individual diopter adjustments. \ control knobs
lnterpupillary distance scale Low voltage ment knob Pilot lamp Voltmeter Main switch Analy~erotation / / / / Aperture iris Field iris diaphragm High/low magnification selector lever Position "L" for objective 5X and position "H" for objectives 1X and higher. Filter mount Polarizer mount
Summary of Putting the Microscope in Operation Model BHM Place a specimen on the mechanical stage (see page 13). Adjust the stage height (see page 151. Switch on the transformer. Swing the 1X objective into the light path and coarse focus. Make interpupillary and diopter adjustments (see page 14). Swing in the desired objective. Fine focus. Correct the illumination system. Adjust light intensiw. Adjust aperture iris diaphragm and field iris diaphragm (see page 121. Cut off this page at the dotted line and put it on the wall near the microscope as a reminder of correct microscope operation.
Q V. OPTICAL SYSTEM The optical system of the Series BH is divided into five sections: Objectives, Observation Tubes, Eyepieces, Illuminating System and Photomicrographic Equipment, The following section deals with objectives, eyepieces and illuminating system. 1. Objectives A. Types Two types of Olympus objectives are mentioned below, in accordance with their optical performance and corrections of various aberrations. Achromats: Corrected for chromatic aberration, and most popular for general use. Plan achromats: Capable of producing a flat image to the edge of the field. Recommended for visual observation of a large field and photomicrography of flat objects. B. How to Use Immersion objectives (engrave "HI" for homogeneous immersion): To utilize the full numerical aperture of an immersion objective, the objective and specimen are immersed in an Olympus immersion oil, provided. Care should be taken to prevent oil bubbles from forming in the oil film between specimen and objective. After use, carefully wipe off the immersion oil deposited on the top lens surface of the objective with gauze moistened with xylene. Take care not to immerse objectives other than immersion objectives. Special objectives: Long working distance objectives: Provide a longer working distance than standard objectives of equal power. Differential interference contrast objectives: These strain-free objectives of high N.A. can be used not only for the differential interference contrast method, but also for brightfield.
2. Eyepieces The eyepieces available with the Series BH are computed to correct slight residual errors left uncorrected in the objectives and designed to further magnify the primary image from the objective, limiting the field as viewed by the eye. Widefield eyepiece (WF): Color corrected and flat, w~de field; high eyepoint, convenient for observers wearing eyeglasses. Compensating eyepiece (K): Corrected for chromatic aberration and astigmatism. For use with high power objectives. Photo eyepiece {FK): For photomicrographic use. Fully corrected for field flatness in combination with all Olympus objectives. * The eyepieces mentioned above can be used with drop-in eyepiece micrometer discs. Q Use of eyepiece cap (for standard eyepiece) The eyepiece cap is recommended for those who wear eyeglasses. It prevents damage to the eyeglasses. Q Use of eyepiece with eye shield The eyepiece WFlOX incorporates a sliding eye shield. This eye shield can be polled out to prevent glare and loss of contrast caused by ambient light hitting the eyepiece front lens.
*** BiK5X and BiWF15X are optionally available. * The resolving power is obtained when the objective is used with fully opened aperture diaphragm. ce from the specimen or cover glass to the nearest point of the objective. A longer working distance is covenient to ge to the objective front lens or specimen, or when using a thicker cover glass. abbreviated N.A. A mathematical relationship that directly connects the resolving power and the light-gathering power of e with its aperture. N.A. is the product of the sine of half the angular aperture of a lens, and the refractive index of the rough which the light passes. It is a very important constant for high power lenses. The N.A. values can be used for mparing the resolving power of all types of objectives, dry, water or oil immersion. of a lens to register small details. Resolving power is of vital importance in critical microscopy. The resolving power is measured by its ability to separate two points (line structure in the object may be considered as a row of points). ing power is now placed at R=K Wavey K=cons tant wavelength of the light employed is 4mp to 7m p. Decreasing the wavelength of the light employed increases ng power. The higher the resolving power of an objective, the closer the image will be to the true structure of the object. ce in micron between the upper and lower limits of sharpness in the image formed by an optical system is termed "focal uctures outside these limits are more or less blurred and with low power objectives are apt to interfere with the image in smaller the aperture iris diaphragm setting and the lower the N.A., the larger the focal depth. Lack of focal depth is rent in photomicrography, particularly with low power objectives, as the image is projected on the film in one place. that represents the diameter in mm of the image of the field diaphragm that is formed by the lens in front of it. size of the field of view in mm. Tllis is derived from Field number of eyepiece.'
3, Vertical Illuminator The reflected illumination system adopted in the Model BHM is based on the Koehler principle, with features as follows: @ Aperture iris diaphragm and field iris diaphragm operate effectively @ The light source illuminates the full numerical aperture of the objective. @ The entire field of view can be evenly illuminated. @ The illuminator is provided with a high/low magnification selector lever to exactly match illumination with objective magnification in use. @ Optimum light intensity can be easily obtained.
A. Aperture lris Diaphragm In order to achieve optimum objective performance, the opening of the aperture iris diaphragm should be matched to the numerical aperture of the objective in use. It is often preferable, however, to stop down the aperture diaphragm slightly more than indicated by the objective N.A. This will result in better image contrast, increased depth of focus and a flatter field. After completing focus adjustment, remove one of the eyepieces from the observation tube and look into the empty eyepiece tube. As you stop down the aperture iris diaphragm, the image of the iris diaphragm can be seen in the objective pupil. Adjust the opening of the diaphragm to match the N.A. of the objective in use. If the specimen is low in contrast, it IS recommended to stop down to 7-8% of the objective N.A. Opening of the diaphragm Objective pupil,--+$\ 8. Field lris Diaphragm The field iris diaphragm controls the diameter of the ray bundle impinging on the specimen surface and thus increases image definition and reduces glare. For microscopic observation, it is necessary to stop down the field iris diaphragm until the diaphragm is just outside the field of view as you look through the eyepiece. For photomicrography, the field iris diaphragm must be stopped down in accordance with the field as viewed through the field of view eyepiece, focusing telescope, etc, in use. VI. LIGHT SOLIRCE The standard light source incorporates a 15W pre-centered tungsten filament bulb (LS15), combined with a socket for positive contact, eliminating the problems of defective contact and over-heating. * When used at the rated voltage 6V, the average life of the tungsten bulb LS15 is longer than 2 hours. This is, however, greatly reduced, if the bulb is used at higher voltage; for instance, the bulb life is reduced to 1/5 at 8V. Therefore, it is advisable to avoid prolonged use at readings over 6V (in the red zone). If high intensity illumination is required, ~t is recommended to use the optional hidh intensity halogen illuminator, * Do not switch the tungsten bulb on at high intensity. It reduces bulb life.
VII. STAGES 1. Removal of Specimen Holder 1) Square mechanical stage with right-hand low drive controls Model BH-SV The standard mechanical stage is provided with a springloaded specimen holder, which is capable of holding specimens up to 55rrtm x 85mm in size. The specimen holder is removable to obtain a large unobstrticted stage surface, (Fig. 1) 2) Large mechanical stage Model BH-SIC This 2Omm x 161 mm square mechanical stage has a traversing area of 11 Omm x 1mm, by rneans of coaxial low drive controls. It is possible to adjust the distance between the holders according to specimen sizes, For exceptionally large specimens, the holders cart be removed. For use with IC wafers, masks or other special specimens, custonier designed specimen holders can be utiliied. I Fig. 1 I 2. Stage Spacer In order to prevent interference between objectives and specimen holder it is recommended to use the stage spacer provided w~tti the stage Model BH-SV and place it in the manner shown in Fig. 3, prior to placing a thin specimen on the stage. (Fig. 3) 3. Metal Slides To level a specimen: 1) Put plasticine on a metal slide supplied. 2i Place a specimen on the plasticine, and press the specimen with a hand press until the specimen surface is Fiq. 3 properly leveled. * It is suggested to place a piece of tissue paper between the specimen and the plunger of the hand press in order to prevent scratching of the polished specimen surface. (Fig. 4) Fig. 4
, OBSERVATION TUBE lnterpupillary Distance and Diopter Adjustments 1) Hold the knurled dovetail slides @ of the right and left eyepiece tubes with both hands and push the tubes together, or pull them apart laterally, whichever is required, while looking through the eyepieces with both eyes, until perfect binccular vision is obtained. 2) Memorize your interpupillary distance setting. Scale @J is provided for this purpose. Fig. 5 3) Rotate the tube length adjustment ring @ on the right eyepiece tube to match your interpupillary distance setting which you obtained from the scale. (Fig. 5) 4) Look at the image through the right eyepiece with your right eye and focus on the specimen with the fine adjustment knobs. 5) Next, look at the image through the left eyepiece with your left eye and rotate the tube length adjustment ring @ to focus on the specimen without using the coarse and fine adjustment knobs. * The mechanical tube length of the Olympus metallurgical microscope is standardized at 2mm. 2. Light Path Selection The trinocular observation tube is provided with a light path selector lever to direct the light to the observation tube or to the photo tube, Lever position Pushed in all the way Pulled out all the way Amount of light 1% into binocular tube 2% into binocular tube 8% into photo tube Application (1) Normal observation 12) Dark specimens (1 Photomicrography (2) Observation of excessively bright specimens - * In case of long time exposure, it is necessary to darken the room or put a pair of light shield caps, provided with the trinocular tube, on the eyepiece tubes, in order to prevent light from coming on the film plane.
FOCUSING ADJUSTMENT Tension Adjustment of Coarse Adjustment Knobs A tension adjustment ring @ is provided next to the right hand coarse adjustment knob. With this device the tension of the coarse adji~stment is freely adjustable for either heavy or light movement, depending on operator preference. (Fig. 6) However, do not loosen the tension adjustment ring too much, because the stage drops or the fine adjustment knobs slip easily. 'k Be careful not to rotate the right and left coarse adjustment knobs in the opposite direct~on simultaneously. (Fig. 6i Fig. 6 2. Automatic Pre-focusing Lever This lever @ is provided to prevent possible contact between specimen and objective as well as to simplify coarse focusing. The lever is locked after coarse focus has been accomplished. This prevents further upward travel of the stage by means of the coarse adjustment knobs, and automatically provides a limit~ng stop if the stage is lowered and then raised again. The automatic pre-foctising lever does not restrict fine focusing. (Fig. 7) Fig. 7 3. Stage Height Locking Lever In addition to the vertical movement of the stage by means of coarse and fine adjustments, the stage height position can be changed by means of the stage height locking lever @. Maximum specimen height is 55rnm with the standard objectives, and 37mm with the differential interference contrast attachment. (Fig. 8)
X. TROUBLESHOOTING Troubles 1. Optical System Causes Remedies (a] With the illuminator switched on, the field of view cannot be seen. (b)the field of view is cut off or illuminated irregularly. The field iris diaphragm is not opened sufficiently. The light path selector lever is stopped midway. The nosepiece is not clicked into position. The field iris diaphragm is stopped down excessive1 y. The bulb or lamp house is not correctly positioned. Open the field diaphragm fully. Push the lever all the way. Slightly rotate the nosepiece until it clicks into position. Open the diaphragm sufficiently Insert the bulb or lamp house all the way. The highilow magnification selector lever of the illuminator is not correctly positioned. I (c) Dust or dirt is visible in / Dust or dirt on the bulb end. 1 I I the f ied of view. Dust on half mirror. 1 Dirty specimen. Dust on eyepiece. I / prism in the observation tube. I (d)excessive image contrast. Dust on the lower surface of the ped down excessively. Position the lever correctly.. Clean off the dust or dirt. Open the diaphragm. (e) Resolution problems: I ) Image is not sharp. 2) Insufficient contrast. The highilow magnification selector lever is not correctly positioned. The bulb or lamp house is not correctly positioned. The objective is not correctly positioned in the light path. Dirt on objective front lens. The immersion objective is used without immersion oil. Bubbles in the immersion oil. The Olyinpus specified oil is not used. The specimen is not properly illuminated. Place the lever in correct position. Push the bulb or lamp house ail the way home. Slightly rotate the nosepiece until it clicks into position. Clean the objective. Apply immersion oil. Remove bubbles, Use the specified oil Adjust the illumination.
- - Troubles Causes Remedies (f) The field of view IS The ob~ectlve IS not correctly poslpart~ally out of focus. tioned ~n the lrght path ~t clicks lnto positlon I The Image is partly out of focus. Slightly rotate the nosepiece unt~l =-not correctly pos- I Place the specmen on the stage and tioned on the stage. I secure it with the specimen holder. G i m e n surface 1s not at rrght Level the specimen surface cor- I angles w~th the opt~cal axis. rectly wrth a hand press. l- The high/low magnification selector Turn the lever all the way until ~t lever 1s not properly operated (or stops in position. I the lever 1s pos~tioned mrdway) (gf When objectives are changed, they are not parfocal. 2. Electric System (a)the light flickers and ' the intensity is varying. Mechanical tube length adjustment 1 rings on observat~on tube are not correctly adjusted. The filament of the bulb is likely to burn out. Adjust the rings correctly. Loose electrical connection. Secure the connection. (b)the pilot lamp lights / The bulb is burned out. I Replace the bulb. I but the illuminator I does not. k ~ r i cconnect~on. a Secure the connection. I {c) Reduced bulf I~fe. Ma~ns voltage is too hlgh. Use the tungsten bulb under 6V as well as possible, or use a high intensity light source, such as a halogen illuminator. 3. Focusing I (a) Coarse adjustment - is 1 ension adjustment ring is tighten- the adjustment ring protoo tight. ed too much. The user is trying to raise the stage passing over the upper focusing lrmit imposed by the engaged prefocus~ng lever. 1 Unlock the pre-focusing lever. iblthe stage drops and the specimen goes out of focus. The tension adjustment ring is too loose. Tighten the ring properly. (c)the stage cannot be raised to the upper limit of the working range. The pre-focusing lever is engaged in positioning the stage lower than the focusing position. ----- The stage height locking lever is engaged in a position lower than the focusing range. Unlock the pre-focusing lever. Unlock the lever, and raise the stage to the proper height, then lock the lever.
Troubles Causes Remedies (d)the stage cannot be lowered to the lower limit. 1 4. Observation Tube I (a) Incomplete vision. binocular The stage is locked higher than focusing position. lnterpupillary distance is not correctly adjusted. Loosening the stage height locking lever, lower the stage to a proper height, and then lock the lever. Correct the interpupillary distance. Diopter adjustment is incomplete. Right and left eyepieces are not matched. The user is unaccustomed with a binocular vision. Complete the diopter adjustment. Use a pair of matched eyepieces. Prior to looking at the binocular image of the specimen, try to look the entire field of view, or look at a far away object before resuming microscopic observation. 1 5. Stage (a)the Image moves eas~ly when you touch the stage. The stage IS not correctly clamped. The stage height locking lever is not tightened. Clamp the stage securely. Tighten the lever securely.
OWlsPCWOFnCALCm..)1D. 43-2, HATAGAYA?&HOME, SHIBUYA-MU TOKYO, JAPAN I