EMULATOR IMMO MERCEDES CR1 aimmo.com.com.caim 1
Vito 2,2 Cdi 5 plugs A-Class 1,7 Cdi 5 plugs EDC/MSA15.1 2,5 Td 2,9 Td 3,0 Td 1 plug with mechanical and electronic ignition switch aimmo.com ECM Bosch with HC11E9 in vehicles with engines of 320-6 cylinders, 430-8 cylinders ML 320 and 2,0 gasoline SLK 1998. with mechanical ignition switch Lucas 4 plugs E-class, 2,2 diesel with mechanical and electronic ignition switch.com A-Class ECM VDO MSM 1,4 1,6-1,9 gasoline.caim 2
Thank you for purchasing our device. Emulator immo to Mercedes replaces damaged immobilizer or the car key for the group of Mercedes cars. It function after made changes in memory content of Engine Control Module ECM. aimmo.com In case of losing the car keys or a car burglary, it enable to drive off from the road to the car service. Due to a low cost, you can leave it in the car instead of buying a new immo or making car keys duplicate. There is a possibility of using it as the additional security!!!.com Red LED indicating about transmission: will blink and turn off after properly working..caim 3
When emulator is connected, disconnect CAN from original immo! aimmo.com.com A-class 1,7Cdi 5 plugs.caim 4
aimmo.com.com Vito 2,2 Cdi 5 plugs.caim 5
Vito Cdi 5 plugs aimmo.com.com Mercedes Vito 2,2 CDI the starter does not starting, there is an inscription at the instrument cluster start error..caim 6
aimmo.com.com The driver is positioned at the passenger side..caim 7
aimmo.com Connecting emulator to ECM 5 plugs Vito:.com GND 1. 04,1.05, 1.06 CAN-H 2.11 CAN-L 2.12 ACC 2.13.caim 8
aimmo.com.com In the ECM of Vito engine, 5 plugs CR1, find memory 24c04..caim 9
aimmo.com.com In the memory 24c04 in address: 1EE to 1F9 type: 2A 4E 00 00 FF FF 00 9C D4 13 56 01. Disconnected CAN from WSP!!! 10.caim
A-Class 1,7 Cdi 5 plugs imm aimmo.com.com Mercedes A-class 1,7 CDI the starter does not starting, there is an inscription at the instrument cluster start error. ECM under bonnet on left the side behind engine, covered by plastic. 11.caim
aimmo.com Connecting emulator to ECM 5 plugs A-class:.com GND 1.04, 1.05, 1.06 CAN-H 2.11 CAN-L 2.12 ACC 2.13 12.caim
aimmo.com In the A-class engine drivers, 5 plugs CR1 find memory 24c04..com 13.caim
aimmo.com In memory 24c04 in the address 1EE to 1F9 type 2A 4E 00 00 FF FF 00 9C D4 13 56 01..com Disconnected CAN from WSP!!! 14.caim
EDC/MSA 2,5 Td 2,9 Td 3,0 Td 1 plug - Sprinter 2,9 Td - E210 3,0 Td - C250 2,5 Td aimmo.com.com 15.caim
aimmo.com In an older type of engine control module ECM, 1 plug, need to find the memory 24c02 marked as B58 or memory 24c04..com In memory 24c02 in address 38 and 39 type 2A 4E and in addresses from 3F to 42 type 9C D4 13 56. 16.caim
aimmo.com Connecting emulator to ECM, EDC 1 plug. CAN H and CAN L to the suppressor. GND from LED. Power from LED. If there are problems with start, add ACC on 13 pin computer EDC (take it from second leg of LED)..com Disconnect CAN from WSP!!! 17.caim
ECM Bosch with HC11E9 in vehicles with engines of 320-6 cylinders, 430-8 cylinders ML 320 and 2,0 gasoline SLK 1998. with mechanical ignition switch imm aimmo.com.com 18 In ECM is Motorola, 4E28B HC11E9 52PLCC write from addresses 019 to 01d values FF (ETL 619 to 61E) and make personalization by tester HTT or Star Diagnosis because engine must work 60 seconds, to finish coding..caim
Lucas 4 plugs E-class, 2,0 diesel with mechanical and electronic ignition switch. aimmo.com.com E-class Mercedes 2,0 diesel 1996 Lucas A0195459432 ed013 sw25.96 fd30.96 19.caim
aimmo.com.com 20 Driver is positioned on the passenger side in the engine compartment. Connecting Emulator to ECM. power supply pin 16A CAN L pin 10A CAN H pin 1A ground pin 18C After connecting make personalization by tester.caim
HHT or Star Diagnosis. aimmo.com.com 21 Motorola HC11KW1 quartz 8Mhz -connecting programator X-Prog to motorola: pin 63 Vss mass GND pin 64 Vdd + 5V Vcc pin 69 reset B pin 70 Mod B to mass B4 pin 71 Mod A to mass GND pin 72 RXT B3 pin 73 TXD B2 Connect together pin 70 i 71 before making connection by head of cable with wire solder to mass. In ECM is Motorolla HC11KW1 cleaning from adress 22A to 22F on FF and make personalization of tester HHT or Star Diagnosis because engine must work about 60 second to finished coding. Disconnect CAN from WSP!!!.caim
A-class ECM VDO MSM 1,4 1,6-1,9 gasoline aimmo.com.com ECM is set up on air delivery pipe to engine with Air Mass Flow Sensor. 22.caim
aimmo.com Connecting emulator: red power suplly +12V ACC blue ground green CAN-H white - CAN-L.com 23.caim
To read and make change in memory, use Wellon programmer. aimmo.com After memory flash is read 29F200 (44pin) write in search window value 03 40 (or 04 40)..com 24.caim
aimmo.com.com 25 All values 03 40 (or 04 40) which will be find under chassis number change into 03 01 (or 04 31). After soldering we personalize by the Star Diagnosis. Disconnect CAN from WSP!!! Warning!!! Due to possible construction changes of the cars, before connecting the device check signals by multimeter on the immobilizer plug or in ECM.caim
We state, that we are the only authentic authors of this manual. We possess copyright to this publication. All rights reserved. Unauthorized copying, hiring, lending, public performance will be punished!!! Any trials of unauthorized copying, hiring, quoting prohibited!!! Both service and advertisement constitute copyright and they are the subject to the protection in accordance with the Act from 4 th Feb. 1994 on Copyright and Related Laws (Statute Book no. 24 position 93) and protection on the basis of the Act from 8 th June 1993 on combating an unfair competition (Statute Book no. 47 position 211) aimmo.com.com 26.caim