Polyester Powder Coated Bracket and Sprg Coil Self-Centerg Cap Patent No. 5,6,426 Application Ketics Model SRH hangers are used to isolate suspended sources of both noise and vibration. Suspended mechanical equipment such as -le fans, cabet fans, and pipg and ductwork close proximity to mechanical equipment are typical uses of Model SRH hangers featurg the patented No-Short self-centerg cap. Ketics mimum recoendation for the placement of sprg hangers is that they be stalled on all pipg the equipment room and on the first 50' (15 m) for pipg that extends outside of the equipment room. For typical stallations, the three sprg hangers closest to the equipment should have equal deflection to the equipment isolators. The remag sprg hangers should have a mimum deflection of 1" ( ). In noise sensitive areas, the pipe hangers selected should have the same deflection as that specified for the equipment isolation and all pipg the buildg should be isolated. High sound transmission loss ceilg systems can be isolated by the use of SRH hangers the ceilg suspension system. Standard SRH hangers are shipped fully assembled and ready for stallation threaded metal rod suspension systems. Model SRH hangers are available a wide range of load and static deflection selections and can be provided with labor-savg accessories for adaption to wire or strap suspension systems, and sprg may be preloaded for ease erectg pipg at a fixed elevation. KINETICS TM 1" and 2" Deflection Isolation Hangers Model SRH Description Ketics SRH vibration isolation hangers consist of free-standg, large diameter, laterally stable steel sprgs series with an elastomer-shear sert, assembled to a stamped or welded hanger bracket. To assure stability, the sprg element has a mimum lateral sprg stiffness of 1.0 times the rated vertical stiffness. Hangers with properly deflected coils will allow a support rod misalignment through a 30 arc without short circuitg. Isolation brackets will carry a 500% overload without failure. Hangers are available deflections from 1.20" to 2.40" (30 to 61 ), and capacities from 35 to 3500 lbs. ( to 1588 kg). Model SRH hangers are superior to hangers which corporate only sprgs, which can transmit noise through the all metal construction, and hangers which corporate only pads, which can transmit low frequency vibration. Ketics Model SRH hangers are recoended for the isolation of vibration produced by suspended mechanical equipment, low-speed suspended fans, transformers, ductwork, pipg, etc. How the self centerg no short cap works: Indexed steps sprg cap correspond to standard washer diameters for the appropriate rod diameter. The washer and rod stay centered the cap.
Specifications Vibration isolators for suspended equipment with mimum static deflection requirement exceedg 0. 4 " ( 1 0 m m ), a n d w h e r e b o t h h i g h a n d l o w f r e q u e n c y vibrations are to be isolated, shall be hangers consistg of a laterally stable sprg series with an elastomer--shear sert complete with load transfer plates and assembled a stamped or welded steel bracket. The bracket shall be fished with an polyester-based p o w d e r c o a t i n g. T h e m a n u f a c t u r e r s h a l l p r o v i d e dependent laboratory testg showg that the bracket with this fish has endured a mimum of 1,000 hours of exposure to salt spray fog testg per ASTM B117 without signs of corrosion. T h e e l a s t o m e r i n s e r t s h a l l b e m o l d e d f r o m o i l - r e s i s t a n t compounds and shall be color coded to dicate load capacity and selected to operate with its published load range. The sprg element shall have a mimum lateral stiffness of 1.0 times the rated vertical stiffness. Sprgs shall be color coded or otherwise identified to dicate load capacity. The hanger bracket shall be designed to carry a 500% overload without failure and to allow a support rod misalignment through a 30 arc without metal-tometal contact or other short circuit. The hanger bracket shall corporate sprg caps with dexed steps which correspond to the washer diameter of the appropriately sized hanger rod to keep the rod centered the sprg cap and reduce rod misalignment. I s o l a t i o n h a n g e r s s h a l l b e s e l e c t e d b y t h e m a n u f a c t u r e r f o r e a c h s p e c i fi c a p p l i c a t i o n t o c o m p l y w i t h d e fl e c t i o n r e q u i r e m e n t s a s s h o w n o n t h e Vibration Isolation Schedule or as dicated on the project documents. The combation isolation hanger assembly with neoprene sert shall be Model SRH, as manufactured by Ketics Noise Control, Inc.
Hanger Type SRH-1-35 SRH-1-70 SRH-1-1 SRH-1-245 SRH-1-370 SRH-1-500 SRH-1-600 SRH-1-700 SRH-1-805 SRH-1-50 SRH-1-100 SRH-1-0 SRH-1-450 SRH-1-6 SRH-1-800 SRH-1-1000 SRH-1-10 SRH-1-1700 SRH-1-00 SRH-1-2465 SRH-1-2865 SRH-1-3500 SRH-2-35 SRH-2-70 SRH-2-120 SRH-2-0 SRH-2-260 SRH-2-465 SRH-2-720 SRH-2-850 SRH-2-10 SRH-2-1200 SRH-2-2000 SRH-2-00 SRH-2-2750 SRH-2-30 SRH-2-30 Sprg Color Chrome /Wht Chrm/Wht Chrome Black Red Org/ /Gry /Brn Black White Chrome Blu/Blu Blu/Grn Blu/Blk lbs 35 70 1 245 370 500 600 700 805 50 100 0 450 6 800 1000 10 1700 00 2465 2865 3500 35 70 120 0 260 465 720 850 10 1200 2000 00 2750 30 30 kg 32 111 8 7 272 318 365 23 45 1 204 283 363 4 567 771 998 1118 00 1588 32 100 118 211 327 386 465 5 909 16 10 75 17 Load 1.61 1.55 1.56 1.52 1.29 1.45 1.35 1.40 1. 1. 1.19 2.12 1. 1.80 1.55 1.45 1.38 1.35 1.52 1.58 1.67 1.82 2.09 2.19 2.32 2.29 2.21 2.01 2.08 1.97 1.99 2.08 2.10 2.12 2.14 2.14 41 39 40 39 33 37 34 36 32 29 30 49 46 37 37 35 34 39 40 43 46 56 59 58 56 50 Deflection L 1 1 1 1 1 H W A Dmax Sprg O.D. Standard Ratgs Dimensiosn
keticsnoise.com/hvac/srh.html sales@keticsnoise.com 1-800-959-19 Manufacturg facilities Ohio, USA and Ontario, Canada. Sales offices worldwide. Ketics Noise Control, Inc. is contually upgradg the quality of our products. We reserve the right to make changes to this and all products without notice. SRH 1 and 2 12/
KINETICS TM 4" Deflection Isolation Hangers Model SRH Application Ketics SRH hangers are used to isolate suspended sources of both audible and audible noise and vibration. Suspended mechanical equipment such as -le fans, cabet fans, and pipg and ductwork close proximity to mechanical equipment are typical uses of Model SRH hangers. Ketics mimum recoendation for the placement of sprg hangers is that they be stalled on all pipg the equipment room and on the first 50 ft (15 m) for pipg that extends outside of the equipment room. For typical stallations, the three sprg hangers closest to the equipment should have equal deflection to the equipment isolators. The remag sprg hangers should have a mimum deflection of 1. ( ). In noise sensitive areas, the pipe hangers selected should have the same deflection as that specified for the equipment isolation and all pipg the buildg should be isolated. Standard Model SRH hangers are shipped fully assembled and ready for stallation threaded metal rod suspension systems. Model SRH hangers are available a wide range of load and static deflection selections and can be provided with labor-savg accessories for adaption to wire or strap suspension systems, and sprg may be preloaded for ease erectg pipg at a fixed elevation. Description Ketics SRH Vibration Isolation hangers consist of free-standg, large diameter, laterally stabile steel sprgs series with an elastomer-shear sert, assembled to a welded hanger bracket. Hangers corporate a high deflection, color-coded sprg element with load transfer plate and a 0.4. (10 ) deflection elastomeric isolator complete with load transfer plate. To assure stability, the sprg element has a mimum lateral sprg stiffness of 1.0 times the rated vertical stiffness. Sprgs are polyester powder coated, with a 1000 hour salt spray ratg per ASTM B-117. Hangers will allow a support rod misalignment through a 30 arc without short circuitg. Isolation brackets will carry a 500% overload without failure. Hangers are available deflections from 4.09. to 4.40. (104 to 112 ), and capacities from 100 to 3850 lbs. (46 to 17 kg). Model SRH hangers are superior to hangers which corporate a sprg only, which will transmit noise through the all-metal construction, and hangers which corporate noise stop pads only, which will transmit low frequency vibration that a sprg can isolate. Ketics Model SRH combation hangers are recoended for the isolation of vibration produced by suspended mechanical equipment, low speed suspended fans, transformers, ductwork, pipg, etc.
Hanger Type Sprg Color Rated Load lbs kg Deflection L H W A B Dmax SRH-4-100 SRH-4-0 SRH-4-500 SRH-4-750 SRH-4-1000 SRH-4-10 SRH-4-00 Black Red 100 0 500 750 1000 10 00 45 114 7 341 4 568 726 4.09 4. 4.15 4. 4.30 4.37 4.38 104 107 107 109 111 111 1 1 1 1 1 1 1 SRH-4-50 SRH-4-00 SRH-4-2750 SRH-4-3000 SRH-4-30 SRH-4-3500 SRH-4-3850 Bge/Blu Bge/Grn Bge/Blk Bge/Red Bge/Brn Bge/org 50 00 2750 3000 30 3500 3850 3 15 1249 62 14 1589 17 4. 4.59 4.65 4. 4.14 4.14 4. 115 117 118 106 3.52 3.52 3.52 89 89 89 Specifications Vibration isolators for suspended equipment with mimum static defl ection requirement exceedg 0.4. (10 ), and where both high and low frequency vibrations are to be isolated, shall be hangers consistg of a laterally stabile steel sprg series with an elastomer--shear sert complete with load transfer plates and assembled a welded steel bracket. The bracket shall be fi nished with an polyester powder coatg. The manufacturer shall provide dependent laboratory testg showg that the bracket with this fi nish has endured a mimum of 1,000 hours of exposure to salt spray fog testg per ASTM B117 without signs of corrosion. The elastomer sert shall be molded from oil-resistant compounds and shall be color coded to dicate load capacity and selected to operate with its published load range. The sprg element shall have a mimum lateral stiffness of 1.0 times the rated vertical stiffness. Sprgs shall be color coded or otherwise identifi ed to dicate load capacity. The hanger bracket shall be designed to carry a 500% overload without failure and to allow a support rod misalignment through a 30 arc without metal-to-metal contact or other short circuit. Isolation hangers shall be selected by the manufacturer for each specifi c application to comply with defl ection requirements as shown on the Vibration Isolation Schedule or as dicated on the project documents. The combation isolation hanger assembly with neoprene sert shall be Model SRH, as manufactured by Ketics Noise Control, Inc. keticsnoise.com/hvac/srh.html sales@keticsnoise.com 1-800-959-19 Manufacturg facilities Ohio, USA and Ontario, Canada. Sales offi ces worldwide. Ketics Noise Control, Inc. is contually upgradg the quality of our products. We reserve the right to make changes to this and all products without notice. SRH 4 12/