High Performance Railway Power



Similar documents
Power transformers. Special transformers Railway

Estimation of electrical losses in Network Rail Electrification Systems

Multi-conductor Train Simulations for Electrification Systems

Earthing Guidance Notes

Knowing the FACTS. FACTS that enhance power quality in rail feeder systems

Appendix 7. Conceptual Design of Electrification System. December 2010

Step Voltage Regulators

Modeling of Transmission Lines

Interfacing electrification and system reliability. Earthing of AC and DC railways 4,10,13

Simple Methods for Calculating Short Circuit Current Without a Computer By Dennis McKeown, PE GE Senior System Application Engineer

DISCONNECTORS AND LOAD SWITCHES for railways

The electrical energy produced at the gen

Steady State and Transient Short Circuit Analysis of 2x25 kv High Speed Railways

Simulation of Cable Overloading Problem on a University Distribution System

CONTROLS DATA MANAGEMENT PROCESS AUTOMATION EUROCUBE. General purpose single phase thyristors and solid state relays Product data.

Impedance Matching and Matching Networks. Valentin Todorow, December, 2009

Digital Energy ITI. Instrument Transformer Basic Technical Information and Application

The following table shows approximate percentage wise the

SIMULATING HYBRID ENERGY GRIDS IN SMART CITIES FOCUS ON ELECTRIC ENERGY SYSTEMS

AMSC s Superconductor Cable Technologies for Electric Utilities

Application Note. So You Need to Measure Some Inductors?

pole, 8 A Safety relay. Screw terminal. 35 mm rail (EN 60715) mounting. 2 CO (DPDT) 8/15 250/400 2, /0.65/0.

Figure. 1 - Split Phase 240/120V circuit (180 phase shift)

CHAPTER VIII LINE PLANT SYSTEM COMMUNICATION THROUGH RE CABLE

Evaluation of first power simulation

Alternating Current and Direct Current

Current valve. for AC 24 V pulse/pause control of electrical loads up to 30 kw

Measure 9: Updating the interoperability directives on high-speed and conventional railway networks First page:

Full representation of the real transformer

48 SERIES Relay interface modules 10 A

Line Reactors and AC Drives

CAT AVR V2.3. Instruction Manual. Voltage regulator for generators. March 2008

Module Title: Electrotechnology for Mech L7

38 Series - Relay interface modules A

Properties of electrical signals

Phase Attribute Identification using GPS Technology

DHANALAKSHMI COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING EE ELECTRICAL MACHINES II UNIT-I SYNCHRONOUS GENERATOR

Background Information

EMTP STUDIES PERFORMED TO INSERT LONG AC CABLES IN THE FRENCH GRID

reduction ore = metal oxides metal oxidation

2. A conductor of length 2m moves at 4m/s at 30 to a uniform magnetic field of 0.1T. Which one of the following gives the e.m.f. generated?

49 Series - Relay interface modules A. Features

Hyperlinks are Inactive

Product brochure Multi Functional Switchgear PASS M kv Flexible and compact switchgear solutions for windfarms

Inductors & Inductance. Electronic Components

Generator Stator Protection, under/over voltage, under /over frequency and unbalanced loading. Ramandeep Kaur Aujla S.NO

Selecting Current Transformers Part 1 By Darrell G. Broussard, P.E.

Reduction of Power Losses Using Phase Load Balancing Method in Power Networks

Radial Distribution Test Feeders

Report on structure and functionalities of the new online energy efficiency screening tool for railways

(3 )Three Phase Alternating Voltage and Current

AN Surging Ideas TVS Diode Application Note PROTECTION PRODUCTS. TRANSIENT IMMUNITY STANDARDS: IEC x

3. TYPES OF SERVICE AVAILABLE. 3.1 Scope

Definition AC Power Distribution

Table of Contents. The Basics of Electricity 2. Using a Digital Multimeter 4. Testing Voltage 8. Testing Current 10. Testing Resistance 12

Business Area Power Supply

EMI in Electric Vehicles

Prepared By: Sheilani Binti Shaari Department of Electrical Engineering/PKB

Summary of Electric Transmission Assessment Report

38 Series - Relay interface modules A

Increasing Data Center Efficiency by Using Improved High Density Power Distribution

0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N

13 ELECTRIC MOTORS Basic Relations

PowerWorld Transmission Line Parameter Calculator

Type SA-1 Generator Differential Relay

Approved Meter Sockets and Cabinets

38 SERIES. Relay interface modules A. EMR Electromechanical Relays. Common features. SSR Solid State Relays. 6.

Short Circuit Current Calculations

Kinetic energy recovery on railway systems with feedback to the grid

Data center power dynamics within the settings of regional power grid

Comparison of Power Título Transmission Line Models with Finite Elements

The Intelligent AX1 Switchgear for Medium Voltage

SHORT CIRCUIT CURRENT CALCULATION AND PREVENTION IN HIGH VOLTAGE POWER NETS

Paralleling Power Sources Which Share a Common Neutral

Electrical Fault Level Calculations Using the MVA Method

VOLTAGE CONTROL IN DISTRIBUTION SYSTEMS AS A LIMITATION OF THE HOSTING CAPACITY FOR DISTRIBUTED ENERGY RESOURCES

Smart Grid and Renewable Energy Grid Integration. Jian Sun, Professor and Director Department of ECSE & Center for Future Energy Systems

INTRODUCTION TO SYSTEM PROTECTION. Hands-On Relay School 2012

DC Traction Power Supply. Powerful, efficient and safe. siemens.com/mobility

Circuits with inductors and alternating currents. Chapter 20 #45, 46, 47, 49

Variable Frequency Drives - a Comparison of VSI versus LCI Systems

How the National Grid System Operates. Chris Gorman Lead Account Executive Syracuse

Treasure Valley Electric Plan - Community Advisory Committee

ISIO 200. Binary Input/Output (I/O) Terminal with IEC Interface

RM17TE V AC. Main. Product or component type. Product specific application. Relay monitored parameters 250 V DC 5 A DC

Type: EASY719 DC RC Article No.: Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC. Description

Electrical safety requirements in DC distribution systems

OFFSHORE WIND FARM ELECTRICAL CONNECTION OPTIONS. W.Grainger 1 and N.Jenkins 2 SYNOPSIS

EARTHING SYSTEM CALCULATION

E-STOP relays, safety gate monitors

Inverter / Charger Installation General Operations and AC and DC Connections

Equipment: Power Supply, DAI, Transformer (8341), Variable resistance (8311), Variable inductance (8321), Variable capacitance (8331)

Three phase circuits

Chapter 11. Inductors ISU EE. C.Y. Lee

Product Data Bulletin

Instrument Transformers Application Guide

Quick Connect. quick - simple - efficient.

Understanding Power Factor and How it Affects Your Electric Bill. Presented by Scott Peele PE

Electric Power Systems An Overview. Y. Baghzouz Professor of Electrical Engineering University of Nevada, Las Vegas

Transcription:

High Performance Railway Power Introduction to Autotransformer system (AT) Banebranchen Session infrastructure May 9th 2012 Tommy O. Jensen/Atkins Danmark 1

Agenda Historical AT system reinvented Principle of operation AT supply system AT system at HSL-railways AT system in Sweden AT system in Norway Advantages/drawbacks of AT Suitable for use in Denmark? 2

Historical Valtellina 3 kv 15 Hz, Italien1902 Introduction of AC-systems 1900 AC locomotives are introduced Ganz develops the first AC locomotive (3 kv) 1905 Many AC systems open in the eastern US, among others New York New Haven (11 kv) 1910 Auto transformer supply tends to become a standard on densely traficated lines in USA (e.g. AT-systems +11/-22 kv 25 Hz) 1915 The Iron Ore line Kiruna-Narvik was electrified (15 kv 15 Hz with 80 kv supply) New Haven-system 11/22 kv 25 Hz CG1- loco at 4.600 kw New York 1934 3

AT system reinvented Increased demands for power necessitates new solutions for train power systems 1972 Japan, Sanyo Shinkansen (25/25 kv 60 Hz) 1981 France, TGV Paris-Lyon (25/25 kv 50 Hz) 1987 Hungary, simplified AT system (25/25 kv 50 Hz) 1995 Sweden, Kiruna Svappavaara (15/15 kv 16,7 Hz) Suitable for busy conventional railways, heavy haul and high speed lines. Substations are expensive and technical complicated installations. 4

Operation for Auto Transformer Principle of operation for an Auto Transformer 250 A e 1 +e 2 e 2 500 A Ampere winding balance: I 1 N 1 = I 2 N 2 ( the ideal transformer ) Power for autotransformator: S AT = U 1 I 1 = U 2 I 2 Common winding = reduced weight, smaller volume, reduced losses Lower price compared to normal two winding transformer. Option for low leak reactance, particularly important in a train power system Draw back no galvanic separation (easier "path" for short circuit currents) 5

Terminology for AT systems Normally used terms: Auto transformer only has one coil with three terminations Primary and secondary side have no galvanic separation *) Plus conductor is connected to contact wire and positive feeder (PL) Minus conductor is only connected to negative feeder (NL) Midpoint termination ideally 0 V is connected to track / return circuit Angel between plus and minus conductors is 180 Normal designations are 2x25 kv or +25/-25 kv *) Power supply (transformer) from the high voltage grid, e.g. 220 kv, will normally be galvanic separated from the train power system. 6

AC supply system Direct supply running rail (RR) or Direct supply with return conductor (RC) Return conductor RC 7

AC supply systems Booster transformer with return conductor (BT-RC) 8

AC supply systems Auto transformer with full range voltage supply (AT-2U) Train power transformer with two secondary coils 9

AC supply systems Auto transformer with contact wire voltage supply (AT-1U) Train power transformer equipped with one secondary coil Some times named AT-Light 10

AC supply systems Earth currents with direct supply (RR) Earth currents with direct supply with return conductor (RC) 11

AC supply systems Earth currents with BT system Earth currents with AT system 12

AC supply systems Why choose a complicated AT system? Source: Comparison of BT and AT system, EMC-symposium York 1-2. July 2004. Prof. György Varju, Budapest University Because supply conditions will improve significantly! 13

AC supply systems Why choose a complicated system? NL (-25 kv) Inductance in an overhead line AC system is heavily dependent on the geometric design PL (+25 kv) CL (+25 kv) Inductance can be reduced by a symmetric configuration and small distances between conductors Reduced EMC impact on the surroundings and reduced stray currents with balanced impedances in PL and FL (reduced "leakage" of currents) RR (0 kv) 14

AC supply systems Why choose a complicated system? Principle of supply (normal operation) Relative impedance Acceptabel distance single track Booster transformer (BT-RC) 100 % 20-30 km Direct (RR-RC) ~ 65 % 30-40 km Direct with supply feeder (RR-RC-FL) ~ 60 % 35-45 km Auto transformer (AT) ~ 20-25 % 60-80 km Possible increased distance between substations Significantly improved quality of voltage Reduced losses Better utilization of brake energy 15

AT system at HSL-railway French AT transformer 225 kv /2x27,5 kv Nominal power 72 MVA (36-36 MVA) SNCF TGV 16

AT system at HSL-railway Electric layout for AT supply Supply station, feeder cables, substation 17

AT system in Sweden Supply system with distributed auto transformers ( AT-Light ) Source: BVS 1543.11601 Kraftförsörjningsanläggningar Autotransformatorsystem systembeskrivning, 18

AT system in Sweden Supply system with distributed auto transformators ( AT-Light ) Banverket AT system 2 x 15 kv AT-transformers 5 MVA Used at Vännas Umeå line 19

AT system in Sweden Supply system with distributed auto transformators ( AT-Light ) 20

AT system in Norway Supply system with distributed auto transformators ( AT-Light ) Omformerstasjon 15 kv samleskinne returstrøm samleskinne 1o km 1o km 1o km Negativledning NL -15 kv Positivledning PL + 15 kv Kontaktledning KL + 15 kv 21

AT system in Norway 22

AT system in Norway 23

Advantages / drawbacks AT-system AT system compared to BT system + Very low voltage drop in overhead catenery system. + Reduced losses in overhead catenary system = saved energy! + Auto Transformer every 10th km compared to Booster Transformer every 3rd km. + Possible longer distance between substations. - More conductors mounted in overhead catenary system. - More complicated switching equipment in train power system - Risk of locally higher earth current caused by higher power levels. BT system employed on lines with parallel signaling and telecommunication cables in order to avoid electromagnetic disturbances. AT system can offers the same advantages. AT system is widely used on high speed lines and railways with heavy freight traffic. AT system can be used on long single track lines to reduce numbers of substations. 24

AT system interesting in Denmark? Electrification 2011 Existing network too expensive to rebuild. Cost for Kystbanen estimated at 120 mio.kr! Lines to be electrified in the future could prove interesting. 25

AT system interesting in Denmark? Electrification till 2020 Lunderskov-Esbjerg København - Ringsted Ringsted Rødby/Femern Note: Yellow substations not yet decided! 26

AT-system interesting in Danmark? Probable development after 2020 The rest of Sealand 2018-2022 Main lines in Jutland 2020-2025 Other local lines 2025-2035 27

Banebranchen Session 2012 May 9th - 2012 Thank you for your attention! Electric railway at Skærum Teglværk 1909 Electric railway at Ørestad 2012 Questions? 28