SCISSOr LIFTS Productguide
H8101ME 3.0tonnemobilemid-risescissorlift Low profile (105mm) structure for on-ground installation Low voltage control Non return valve provides safety against hydraulic failure Dual hydraulic circuit with solenoid valves that protects againest pipe breakage Synchronism of platforms without any torsion bar No mechanical locking therefore no air requirement Set of 4 rubber pads 12 months warranty on parts and labour* Mobile capability, suitable for workshops for limited space Ideal for tyre & car body shops Full access to all sides of vehicles Low profile platform ideal for lifting large range of vehicles including low skirted sport cars Lifting capacity Platform depth Overall width Each platform width Distance between platforms Weight 3000kg 1450mm 105mm 1335mm 535mm 800mm 960mm 450kg 3.0 tonne Mobile Low profile Single phase Ideal for tyre shops
H8101E 3.2tonneshortplatformmid-risescissorlift Low profile (105mm) structure for on-ground istallation Low voltage control Non return valve provides safety against hydraulic failure Dual hydraulic circuit with solenoid valves that protects against pipe breakage Synchronism of platforms without any torsion bar No mechanical locking therefore no air requirement 12 months warranty on parts and labour* Ideal for tyre & car body shops Full access to all sides of vehicles Low profile platform ideal for lifting large range of vehicles including low skirted sport cars Lifting capacity Platform depth Overall width Each platform width distance between platforms Weight 3200kg 1450mm 105mm 1335mm 535mm 800mm 960mm 450kg 3.2 tonne Ideal for tyre shops Low profile Single phase Ideal for tyre and car body shops
H8603/1E 3.6tonneshortplatformhigh-risein-groundscissorlift Hydraulically synchronised platforms Low voltage control system Full access to sides, front and rear of vehicle Low ground clearance ideal for very low skirted vehicles Includes platform extensions (both sides) Hydraulic platforms synchronisation Complete with lifting blocks Control panel allows precise lifting Sensors ensures platform remains level during lifting ratchet safety mechanism 12 months warranty on parts and labour* Improves utilisation of workshop space Ideal for service bays, tyre shops, general repair, brake repairs, suspension and transmission replacement and body shops Flush fitted application allows for vehicles to drive over the platforms in all directions Lifting capacity Platform depth Overall width Each platform width Distance between platforms 3 Phase 1 Phase Pneumatic feed requirement 3600kg 1640mm-2040mm 330mm 2030mm 550mm 930mm 1830mm Motor 380V, 2.2kW Motor 220V 2.2kW 6-8 bar air supply Air and air regulator required 2000 max 3.6 tonne Flush fitted High-rise Three phase or Single phase ratchet locking mechanism
H8903/1E 3.2tonneextralowprofilehydraulicscissorlift Hydraulically synchronised platforms Low voltage control system Full access to sides, front and rear of vehicle Low ground clearance ideal for very low skirted vehicles Hydraulic platforms synchronisation Control panel allows precise lifting Non return valve provides safety against hydraulic failure Dual hydraulic circuit with solenoid valves that protects against pipe breakage Synchronism of platforms without any torsion bar No mechanical locking therefore no air requirement Complete with lifting blocks 12 months warranty on parts and labour* Ideal for service bays, tyre shops, general repair, brake repairs, suspension and transmission replacement and bodyshops Low profile platform ideal for lifting large range of vehicles including low skirted sports cars Lifting capacity Platform depth Overall width Each platform width Distance between platforms 3 Phase 1 Phase 3200kg 1500mm 105mm 1870mm 535mm 800mm 1900mm Motor 380V, 2.2kW Motor 220V 2.2kW 3.2 tonne Low profile High-rise Three phase or Single phase Full access to sides
H88403Sr SHALLOW recess 4.0tonneservice,wheelalignment,Mot&atlscissorlift 180mm recess depth 4400mm & 4800mm platform lengths available Automatically activated, mechanical safety locks Manual device for lowering encase of power failure Optional auxiliary lift for wheel free working Suitable for service, MOT/ATL and alignment purposes Maximum operating stability under all loading conditions thanks to a set of master-slave cylinders with mechanical synchronisation (not electronic) Ideal for service bays, tyre shops and general repair Complete with lifting blocks Fits into many existing recesses Different length platforms gives greater flexibility Automatically activated mechanical safety locks Photocells for platform synchronisation control Limit switch with acoustic warning for the complete lowering Photocells for platform synchronisation Limit switch with acoustic warning on final lowering Dead man controls Capacity Lift/lower Motor Pnaumatic feed requirement 4000kg 4400mm/4800mm 50 seconds 2100mm 3.5kW 230-400v/50Hz-3ph 8-10 bar Air operated and air regulator required 180mm recess - 4400mm or 4800mm platform Fits into many existing recesses Three phase or Single phase Service, MOT/ATL and wheel alignment versions available
H88453SS 4.5tonneservice&wheelalignmentspacesaverscissorlift Control box fitted under platform Suitable for service and alignment purposes The torsion bar (internationally patented), grants the best long-term leveling performances, without maintenance The rear slip plate, reinforced with tempered steel is 1830mm long when fitted to an alignment lift Improves utilisation of workshop space Full access to sides, front and rear or vehicle Ideal for service bays, tyre shops and general repair Complete with lifting blocks 12 Months warranty on parts and labour* More room around lift due to space saving control box Automatically activated mechanical safety locks Photocells for platform synchronisation Limit switch with acoustic warning on final lowering Dead man controls Capacity 4500kg Second scissor capacity 3500kg 4800mm Lift/lower 45 seconds 2125mm Motor 3.5kW 230-400v/50Hz-3ph Pnaumatic feed 8-10 bar filtered/lubricated requirement Air and air regulator required 3 Phase Motor 400V 3/50Hz 3.5kW 4.5 tonne - 4800mm platform Space saving control box** Three phase or Single phase Service and wheel alignment versions available **Only availale on non ATL versions.
H88453 4.5tonneservice,wheelalignment,Mot&atlscissorlift Suitable for service, MOT/ATL and alignment purposes, offers maximum stability and precision during the lifting phase The torsion bar (internationally patented), grants the best long-term leveling performances, without maintenance The rear slip plate, reinforced with tempered steel is 1785mm long when fitted to an alignment lift Improves utilisation of workshop space Full access to sides, front and rear or vehicle Ideal for service bays, tyre shops and general repair Complete with lifting blocks 12 Months warranty on parts and labour* Automatically activated mechanical safety locks Photocells for platform synchronisation Limit switch with acoustic warning on final lowering Dead man controls Capacity 4500kg Second scissor capacity 3500kg 4800mm Lift/lower 45 seconds 2125mm Motor 3.5kW 230-400v/50Hz-3ph Pnaumatic feed 8-10 bar filtered/lubricated requirement Air and air regulator required 3 Phase 3.5kW motor 400V 3/50Hz 4.5 tonne - 4800mm platform Unique patented torsion bar Three phase or Single phase Service, MOT/ATL and wheel alignment versions available Do not scale. Subject to correct maintenance and usage. No liability accepted for specifications
H88503 5.0tonneservice,wheelalignment,Mot&atlspacesaverscissorlift Anti-skid access ramps on the platform allow maximum space on the floor with the lift raised The sliding parts on the metallic wheels are fitted with self lubricating brushes meaning minimal maintenance and maximum reliability over time The lifting arms are made from solid steel bars rather than tubular section bars The mechanical locks grant precision, safety and long life of the lift 12 Months warranty on parts and labour* Automatically activated mechanical safety locks Photocells for platform synchronisation control Limit switch with acoustic warning while lowering Dead man controls Capacity Lift/lower Motor Pnaumatic feed requirement 5000kg 5200mm 50 seconds 2100mm 3.5kW 230-400v/50Hz-3ph 8-10 bar Air operated and air regulator required 5 tonne - 5200mm platform Unique patented torsion bar Suitable for LWB vans Service, MOT/ATL and wheel alignment versions available Do not scale. Subject to correct maintenance and usage. No liability accepted for specifications
PLAN Examplesitelayout
ACCESSOrIES Scissorlifts lightingkit Bradbury s lighting kits are 1.6 metres long and ideal for scissor lifts, 2 post lifts and 4 post lifts- they provide a bright and powerful illumination for the garage s working area. BrS-BradburyrollingSystem This revolutionary Bradbury idea will completely change your working method when used with a Wheel Alignment machine. JackingBeams Bradbury jacking beams are a high quality range which meet all your needs.finger guards fitted as standard.a range of lifting blocks available. Manual or air operated with double extending top beam for MOT use. Lighting Kit Extension Cables A802HE 2 2 m hose extension A803HE 3.5m hose extension SUV/4 x 4 bars H8603E or H8903E 4 x 4 Bars BrS - Bradbury rolling System Compatible with all lifts Pneumatic functioning No power supply needed Easy Installing, plug and play Ideal for 3-D alignments and SUV/OFF road vehicles Capacity up to 3 tonnes Manual/Air Operated Jacking Beams BJB20Sr(A) All class IV MOT, Service, ATL, Scissor & hybrid lifts BJB28r(A)DEATL1591 All class VII MOT, Service, ATL, Scissor & hybrid lifts BJB20r(A)DEATL1391 All class IV MOT, Service, ATL, Scissor & hybrid lifts BJB40r(A)DE All high tonnage lifts
Salesdesk Details of all requirements for a simple and fast installation are available via our sales desk +44(0) 1604 828 648. Frequentlyaskedquestions Equipment will be installed provided: The floor meets the required standard (see detailed site plan) or contact the sales desk. A suitable electrical and air supply to the specification detailed (see detailed site plan) or contact the sales desk. In most cases only one engineer will be installing the equipment suitable labour or lifting equipment should be provided. Any comment as to the suitability of the floor or position of the product given by any of Bradbury Equipment employee is given as advice only. It is the responsibility of the user of the equipment to confirm the site meets the individual site specification detailed within the site plan. Four and five tonne lifts have high columns that require a fork lift for safely completing the installation. A fork truck can be provided at an extra cost if not available on site. installation Bradbury install many thousands of lifts a year most of which are installed quickly and efficiently, we make every effort to ensure that customers/users are fully aware of the specific requirements to ensure this happens If you have any queries please contact our sales desk +44(0) 1604 828 648 note Prices and specifications may change without prior notice, contact our sales desk for latest information +44 ( 0) 1604 828 648. TEAM BRADBURY AREA MANAGER TEAM Scotland GerryGrayArea Sales Manager Tel: 07808 331465 Email: g.gray@bradburyequipment.co.uk northengland tonygilsonarea Sales Manager Tel: 07884 494185 Email: t.gilson@bradburyequipment.co.uk MidEnGland&WalES MarkJonesArea Sales Manager Tel: 07801 978780 Email: m.jones@bradburyequipment.co.uk SoUthEaStEnGland andymoloneyarea Sales Manager Tel: 07808 331466 Email: a.moloney@bradburyequipment.co.uk SoUthWEStEnGland JasonMorganArea Sales Manager Tel: 07970 110223 Email: j.morgan@bradburyequipment.co.uk SALES OFFICE TEAM KeithWMclarenGeneral Manager Tel: 01604 828648 Email: k.mclaren@bradburyequipment.co.uk tracylewis Team Leader Tel 01604 828582 Email: t.lewis@bradburyequipment.co.uk SteveGeorgeArea Sales Administrator Tel: 01604 828583 Email: s.george@bradburyequipment.co.uk oliversextoncad draughtsman & Administrator Tel: 01604 828584 Email: oliver.sexton@bradburyequipment.co.uk JodieWeeksSales and Marketing Co-Ordinator Tel: 01604 828581 Email: jodie.weeks@bradburyequipment.co.uk AFTER SALES DEPARTMENT Tel: 01604 828648 Email: sales@bradburyequipment.co.uk Bradburytrainingacademy The Bradbury Training Academy is available to both distributor and end user customers. It can be used for demonstration of our latest products up to full in depth factory training (sales and service). Available are 2 post, 4 post & scissor lifts, wheel alignment, brake tester, shock absorber, side slip, gas & smoke and tyre equipment. This facility the only one in the UK is available by appointment, please call 01604 828648 to organise a visit. otherbradburyproducts Brake testers motorcycle, car and commercial Commercial vehicle lifts, mobile and fixed Four and two post lifts Gas and smoke Headlamp aligners Hybrid lifts Jacking beams Play detector Pre-fabricated pits Scissor lifts Turn key project Wheel and tyre equipment Wheel alignment lifts and machines BradburyEquipment 153-165 Bridge Street Northampton NN1 1QG T +44(0) 1604 828 648 F +44(0) 1604 609 684 E sales@bradburyequipment.co.uk W www.bradburyequipment.co.uk Registered office 153-165 Bridge Street Northampton NN1 1QG Registered in England 4666699 important Specifications may change without prior notice All images and diagrams are for illustration purposes only. Scissor Lifts 22:10:12 - SIL779