Seat Valves Series SVH0 ctuators are shut-off with virtually zero-leakage, even over a longer period of time Particularly suitable for mobile machines, thanks to the low-weight design and small dimensions Can be used as independent valve blocks, or can be at-tached to the L.8S series of proportional directional valves With suitable upstream control valves, all actuators con-nected to the blocks can be proportionally operated dditional auiliary functions can be implemented Description Series SVH0 low-weight (aluminium) valve blocks feature seat valves and are used to control single or double acting cylinders. They are applied where etremely low levels of leakage are required. The design is based on a direct acting, solenoidoperated / seat valve that seals in both directions. The valves close the flow path to or from hydraulic actuators with virtually zero leakage. Where double-acting actuators are to be controlled, the circuit must include a -position directional valve situated before the seat valves. In its mid-position, this valve must connect the service ports to tank. The SVH0 seat valves are available as: Self-contained monoblocks, with add-on sections Monoblocks for attaching to the L.8S series of proportional directional valves Intermediate and end sections for assembling customerspecific valve blocks. Technical data General characteristics Description, value, unit Nominal flow rate 0 l/min Operating pressure ma. 0 bar Oil temperature -0 C... +80 C Viscosity range 0... 00 mm /s Recommended filtration NS 8 class 9 Nominal voltages or ± 0% Volt DC Power consumption 7 Watt Duty cycle 00 % Enclosure protection IP, DIN 000. Performance graphs p[bar] 0 Values apply to one seat-valve cartridge in the energised position, for both flow directions. Measured with oil viscosity mm /s 8 0 8 Q [l/min] Reference: 00-P-0000-EN-0 Issue: 08.0 /
Monoblocks with add-on sections. Symbols for monoblocks SVH0M**.-.M..G.. actuator ports SVH0M88**.-.M..G.. 8 actuator ports 8 7 SVH0M00**.-.M..G.. 0 actuator ports 0 9 8 7. Dimensions of monoblocks SVH0M**.-.M..G.. SVH0M00**.-.M..G.. 0 9 07 8 7 9 8 9 07 8 0 8 SVH0M88**.-.M..G.. View X 8 7, 0 07 9 8 M8/ 90 7, 0, 0 / 00-P-0000-EN-0/08.0 Seat Valves SVH0
. Symbols for add-on sections.. Intermediate sections.. End sections SVH0Z**.-.M..G.. SVH0**.-.M..G... Dimensions of add-on sections SVH0.**.-.M..G.., 9 70 7, 88 9. ssembly eample SVH0M**D-0M..G.. X=. Manual override Standard covered by cap nut covered by cap nut, with actuating screw covered by cap nut, with fluted knob N H D Notpin I.KT. SW ma. ca..7 Electrical connectors Plug connection to DIN 0 G -wire connecting cable (cable length 00 mm) F Deutsch DT0-P-EP0 with diode PKEC D MP Junior Timer with diode PKEC J 00-P-0000-EN-0/08.0 Seat Valves SVH0 /
.8 Ordering Code Design (see. ) monoblock = M intermediate section = Z ) end section = ) Type of valve body (see. ) actuator ports = ) actuator ports = 8 actuator ports = 8 0 actuator ports = 0 Number of seat valves E. seat valve = 0 seat valves = 0 Manual override (see..) manual override, standard = N manual override covered by cap nut = H manual override covered by cap nut, with actuating screw = manual override covered by cap nut, with fluted knob = D S V H 0 M * * N - 0 M G / X= ) Design number (inserted by the factory) Port threads DIN 8 - M. = M DIN 8 - M. = M Electrical connector plug connection to DIN 0 = G -wire connecting cable (cable length 00 mm) = F MP Junior Timer with diode = J Deutsch connection with diode = D Coil voltage DC Volt = DC Volt = Variants / special features (inserted by the factory) ) Can be combined with LM0 ) Only intermediate and end sections ) Empty stations in blocks (see.7). Unless otherwise stated, the stations beginning from the highest number will be left empty. Diverter valves. Symbol / ssembly eample SVH0WV**.-0MG.. without float position C D E F G H SVH0WV.-0MG.. with float position C D E F G H T T M0 M9 M8 M7 M M M M M M M M M M M M / 00-P-0000-EN-0/08.0 Seat Valves SVH0
. Dimensions SVH0WV**.-0MG.. 00 8 View X 97 M M M M M M M M M 80 0 7 0 M8/7, M M M SVH0WV.-0MG.. 00 8 View X 97 M M M M M M M7 M8 M0 M9 M M M 80 0 7 0 M8/7 89 M M M. The seat-valve functions M : directional function at H M : directional function at G M : directional function at F M : directional function at E M : directional function at D M : directional function at C M7 : float position at H M8 : float position at G M9 : float position at D M0 : float position at C. Manual override Standard N covered by cap nut H covered by cap nut, with actuating screw covered by cap nut, with fluted knob D Notpin I.KT. SW ma. ca. 00-P-0000-EN-0/08.0 Seat Valves SVH0 /
. Electrical connectors Plug connection to DIN 0 G -wire connecting cable (cable length 00 mm) F Deutsch DT0-P-EP0 with diode PKEC D MP Junior Timer with diode PKEC J. Ordering Code S V H 0 W V N - 0 M G / Directional functions CDEFGH = C EFGH = C EFG = Without float position = * With float position at C = With float position at D = With float position at C and D = Without float position = * With float position at G = With float position at H = With float position at G and H = Manual override manual override, standard = N manual override covered by cap nut = H manual override covered by cap nut, with actuating screw = manual override covered by cap nut, with fluted knob = D Design number (inserted by the factory) Port threads DIN 8 - M. = M Electrical connector plug connection to DIN 0 = G -wire connecting cable (cable length 00 mm) = F MP Junior Timer with diode = J Deutsch connection with diode = D Coil voltage DC Volt = DC Volt = Variants / special features (inserted by the factory) / 00-P-0000-EN-0/08.0 Seat Valves SVH0
Single and multi-monoblocks for attaching to L.8S valves. Symbols SVH0M8S.-.. SVH0M888S.-.. 7 8 SVH0M008S.-.. 9 0 7 8 SVH0M8S.-.. SVH0M8S.-... Dimensions View X 8 8 7 8 0 0 M8/7 7 SVH0M8S.-... ) 0, SVH0M8S.-.. Min. length for calculating the total bolt length 7 7 ) 0, 9, 78, 00-P-0000-EN-0/08.0 Seat Valves SVH0 7/
SVH0M8S.-.. ) Min. length for calculating the total bolt length 7 7 0, 9, 98, 7, SVH0M888S.-.. ) 7 8 7 Min. length for calculating the total bolt length 7 0, 9, 98, 7,, SVH0M008S.-.. ) 7 0 9 Min. length for calculating the total bolt length 7 8 7 0, 9, 98, 7, 7,9, ) Threaded plugs for the end of block must be ordered separately (ordering-no.: 008) 8/ 00-P-0000-EN-0/08.0 Seat Valves SVH0
. Seat valve with pressure relief valve SVH0M8S.-0***G.. p=... bar 8 8 0 0 ) 7 9, 9. Manual override Standard covered by cap nut covered by cap nut, with actuating screw covered by cap nut, with fluted knob N H D I.KT. SW ma. ca.. Electrical connectors Plug connection to DIN 0 G -wire connecting cable (cable length 00 mm) F Deutsch DT0-P-EP0 with diode PKEC D MP Junior Timer with diode PKEC J 00-P-0000-EN-0/08.0 Seat Valves SVH0 9/
. ssembly eample SVH0M8SN-0M..G.. X=.7 Ordering Code Type of valve body actuator port with pressure relief valve ) = actuator ports = actuator ports = actuator ports = 8 actuator ports = 8 0 actuator ports = 0 Number of seat valves E. seat valve = 0 seat valves = 0 With interface for series L.8S valves = 8S Manual Override manual override, standard = N manual override covered by cap nut = H manual override covered by cap nut, with actuating screw = manual override covered by cap nut, with fluted knob = D S V H 0 M 8 S N - 0 M G / X= ) Design number (inserted by the factory) Port threads DIN 8 - M. = M DIN 8 - M. = M without (E.: SVH0M8S..) = *** Electrical connector plug connection to DIN 0 = G -wire connecting cable (cable length 00 mm) = F MP Junior Timer with diode = J Deutsch connection with diode = D Coil voltage DC Volt = DC Volt = Variants / special features (inserted by the factory) ) Please specify the required pressure setting in bar. ) Empty stations in blocks (see.). Unless otherwise stated, the stations beginning from the highest number will be left empty. For the end of the block: pcs. threaded plug with profiled sealing ring, M8, ordering-no.: 008 0/ 00-P-0000-EN-0/08.0 Seat Valves SVH0
pplication eamples. Monoblock. Monoblock attached to a series L.8S valve cap screws, he. skt. head SVH0**N-0MG X = cap screws, he. skt. head threaded screws SVH0M8SN-0MG X = SVH0M00**N-0MG SVH0M008SN-0MG =... L/MIN, =... L/MIN b a Eternal preselector valve Internal preselector valve LP8SED00-***-0M8G b a LU8SSCK-0M/0 LU8SZU0 P T LS Specific functional features: ctuator ports and are shut-off with virtually zero leakage. Double-acting cylinders are controlled in both directions by energising the seat valves and and using the preselector valve to determine the direction. Single-acting cylinders are controlled in both directions by energising the seat valve and, to etend the cylinder, operating the preselector valve. float function is obtained by energising seat valves and. 00-P-0000-EN-0/08.0 Seat Valves SVH0 /
info.kl@bucherhydraulics.com www.bucherhydraulics.com 0 by ucher Hydraulics GmbH, D-7977 Klettgau ll rights reserved. Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense. The information does not relieve users from the duty of conducting their own evaluations and tests. ecause the products are subject to continual improvement, we reserve the right to amend the product specifications contained in this catalogue. Classification: 0.00.0.90. / 00-P-0000-EN-0/08.0 Seat Valves SVH0