PRESSURE REDUCING VALVES
|
|
- Amie Atkins
- 7 years ago
- Views:
Transcription
1 0E0-GB PRESSURE REDUCING VAVES MAIN FEATURES The pressure reducing valve is able, by varying its pressure drops, to hold the downstream pressure of the fluid at a constant level against changes in the upstream pressure and flow rate. The pressure reducing valve is used: - in water/plumbing systems: to hold a constant water pressure in the water supply main after the pressure reducing valve; - in plumbing systems/sanitary appliances: to maintain the water pressure constantly below the max. permissible value; - in water/plumbing systems: to save water. By controlling the pressure to the taps, excessive withdrawal of water from the taps is avoided; - in compressed air systems: to keep the air pressure constant in the main, regardless of fluctuations in pressure supplied by the compressors; - after tanks or storage cylinders: to reduce and stabilize the pressure in the main, which is normally lower.
2 GENERA The WATTS Cazzaniga pressure reducing valves Series DRV, DRVN and DRVD are of balanced seat type. This means that the inlet pressure, when acting on the two openings A and B with the same section, is compensated. Therefore it does not exert any force on the pin-plug system when the degree of valve opening changes. Instead, the outlet pressure acts on the diaphragm and hence on the pin-plug system which, therefore, is subjected to two opposing forces, namely: the force exerted by the outlet pressure tending to close the plug, and the pressure exerted by the spring tending to open it. This results in the pressure reducing valve acting like a balanced seat type having the outlet pressure almost unaffected by variations in upstream pressure. SETTING The difference between the downstream pressure P measured with zero flow rate and the same pressure measured with a general flow rate Q represents the pressure drop DP across the pressure reducing valve. It depends on the flow rate as shown in the pressure drop diagrams. If it is required for the upstream pressure not to exceed a given value P, this should be adjusted to value P when the flow rate is zero. At flow rate Q, the downstream pressure will be below the value P by an amount equal to pressure drops DP. When the pressure reducing valve is installed to ensure that the downstream pressure reaches a given value P at a certain flow rate Q, this pressure should be adjusted to value P + DP when the flow rate is zero. At flow rate Q the downstream pressure will be equal to P. SIZING The valve selection criterion consists in determining the diameter so that the speed of the fluid does not reach excessive levels, at nominal flow rate, thus causing excessive pressure drops and noisy effluent which are transmitted to the supply main. The flow rate-speed diagrams provide a guide for selecting the valve diameter in the case of liquids (see water) or gases with pressures of to 0 bar (see air). EXAMPES OF SIZING Example (cavitation) Pressure reducing valve with: Inlet pressure P = bar Outlet pressure P = 3 bar From the cavitation diagram it can be seen that the pressure reducing valve works constantly in the red zone. To avoid rapid deterioration, two valves can be used, one connected upstream to the other. Upstream valve: pressure change from to bar (green zone) Downstream valve: pressure change from to 3 bar (green zone). Example (flow rate) Pressure reducing valve DRV/N with: Inlet pressure (min.) P = bar Outlet pressure P = bar Max. flow rate Q = 0 l/min From the flow rate-speed diagram it can be seen that a diameter of 0 or can be used. The pressure drop diagram shows that in the two cases: DRV0/N Q = 0 l/min DP =. bar DRV/N Q = 0 l/min DP = 0. bar DRV Diaphragm pressure reducing valve with single balanced seat. Ensures min. pressure drops with high flow rates. Downstream pressure set by means of the setting screw () and is locked with lock nut (3) DRVM ike DRV, but with pressure gauge Ø0 for reading downstream pressure /speed diagram DRV - DRVN Speed (m/s) , 0, 0, 0, 00 / MM 000 3/ MM 00 MM 003./ MM 000./ MM 000 MM 003 / MM / MM 003 MM 0033./ MM 0030./ MM 0030 MM DN DN0 DN DN3 DN0 DN0 Air Water 0, 0, 0, 0, 0, 0, m3/h l/min /speed diagram DRVD Speed (m/s) 0, 0, 0, 0, DN0 DN DN0 DN00 DN DN0 DN00 0, m3/h l/s
3 CAVITATION The cavitation diagram shows three zones of valve operation in relation to the upstream and downstream pressures, namely: zone C: normal duty, no cavitation zone B: medium duty, possible cavitation zone A: heavy duty, the valve cavitates. Continuous operation in the red cavitation zone causes rapid deterioration of the internal parts. If the pressure reducing valve is to be used in the red zone, please contact the WATTS Cazzaniga Engineering Department. APPICATION APPROVAS - DVGW approval (Arbeitsblatt W 3) - GA approval (DVR to 3) according to DIN 0 class I (noise below 0 db) - SVGW approval (W/TPW0). - TIN approval (Poland) - CSTB approval (NF P 3-00) (DRV, DRV0). - KTW certification for all materials in contact with water. 3 0 Overall dimensions (mm) DRV / DRVM Key:.. 3. ock nut. Setting screw.. Diaphragm. Inlet connection. Pin. Plug 0. Guide bushing. Filters. Outlet connection Cavitation diagram A Cavitation zone B Transition zone C Work zone (bar) Inlet pressure 0 0 Plug Inlet / outlet connections Diaphragm Seal and O-ring Setting screw and lock nut Filters A Downstream pressure B C (bar) TECNICA CARACTERISTICS bar Downstream pressure (outlet). to bar Connections to M / M tailpiece Downstream pressure adjustment (screw ) Clockwise rotation: increase in pressure Downstream pressure gauge (DRV-M only) Pressure gauge Ø0, scale 0 to bar Max. operating temperature 0 C Shot-blasted brass OT Shot-blasted brass OT with nylon fabric - diagram [ bar ] 0,0 0, / 3/././ , 0, 0, 0, DRV0/N DRV0/N DRV3/N DRV/N DRV0/N DRV/N [l/m]
4 APPICATION APPROVAS - DVGW approval (Arbeitsblatt W 3) - GA approval (DRV/N to DRV3/N) according to DIN 0 class I (noise below 0 db) - CSTB approval (NF P 3-00) (DRV/N, DRV0/N). - KTW certification for all materials in contact with water 3 0 Key:.. 3. Adjusting knob. Setting screw.. Diaphragm. Inlet connection. Pin. Plug 0. Filters. Outlet connection Overall dimensions (mm) DRVN / DRVMN Plug Inlet / outlet connections Diaphragm Seal and O-ring Setting screw Filters DRVN Diaphragm pressure reducing valve with single balanced seat. Ensures min. pressure drops with high flow rates. Downstream pressure set by means of knob (3) with adjustment scale to bar. DRVMN ike DRVN, but with pressure gauge Ø0 for reading downstream pressure. 00 / MM 000 3/ MM 00 MM 003./ MM 000./ MM 000 MM 00 / MM 000 3/ MM 00 MM 003./ MM 000./ MM 000 MM Shot-blasted brass OT Reinforced plastic with nylon fabric TECNICA CARACTERISTICS bar Downstream pressure (outlet). to bar Connections to M / M tailpiece Downstream pressure adjustment (knob 3) Clockwise rotation: increase in pressure Downstream pressure gauge (DRV-M/N only) Pressure gauge Ø 0, scale 0 to bar Max. operating temperature 0 C - diagram [ bar ] 0,0 0, / 3/././ , 0, 0, 0, DRV0/N DRV0/N DRV3/N DRV/N DRV0/N DRV/N [l/m]
5 APPICATION APPROVAS - ASSE, ANSI, CSA, UPC (USA) approvals - WATTS Patent, U.S. Patent N WATTS Patent, U.S. Patent N 3.. BY-PASS 3 Key:.. 3. Setting screw. ock nut.. Inlet connection. Diaphragm. Valve seat. Outlet connection 0. Filter. Filter cap. Plug 3. Guide bushing. By-pass EXPANSION Plug Inlet connection Diaphragm Seal and O-ring Setting screw and lock nut Filters UB (WATTS Patent, U.S. Patent N 3.. ) Diaphragm pressure reducing valve, single seated, with spring. Ensures min. pressure drops with high flow rates. Provided with upstream filter having ample surface and separate connection for easy cleaning. Downstream pressure set by means of screw (3). Fitted with by-pass valve, it allows freeing on the upstream main any overpressure at downstream side (generated, for example, by expansion of water in the water heaters). 0 / FF 00 3/ FF 0 FF 03./ FF 00./ FF 00 FF Cast iron Nordel with nylon fabric UPSTREAM PRESSURE Overall dimensions (mm) UB PUG REDUCED PRESSURE TECNICA CARACTERISTICS 0 bar Downstream pressure (outlet) Adjustable. to bar Upstream connection to F threaded tailpiece Downstream connection F threaded Downstream pressure adjustment (screw 3) Clockwise rotation: increase in pressure Max. operating temperature 0 C - diagram [ bar ] 0,03 0,0 0,0 / 3/././ ,0 0, 0, 0, 0, 0, DN0 DN0 DN DN0 DN DN [ l/h ]
6 APPICATION DRVD Flanged pressure reducing valve with single balanced seat and spring. Ensures min. pressure drops with high flow rates. Downstream pressure set by means of screw (). Nodular cast iron body faced with epoxy resins. DRVD ike DRVD but with max. inlet pressure: bar. DRVD0 ike DRVD but with max. inlet pressure: 0 bar. PN: bar Pout:.- bar 0003 DRVD0/ " DN0 000 DRVD/ "/ DN 0003 DRVD0/ 3" DN DRVD00/ " DN00 00 DRVD/ " DN 003 DRVD0/ " DN DRVD00/ " DN00 Pout: - bar 000 DRVD0//- " DN0 000 DRVD//- "/ DN 000 DRVD0//- 3" DN0 000 DRVD00//- " DN00 00 DRVD//- " DN 00 DRVD0//- " DN0 000 DRVD00//- " DN00 Pout: - bar 000 DRVD0//- " DN DRVD//- "/ DN 000 DRVD0//- 3" DN0 000 DRVD00//- " DN DRVD//- " DN 00 DRVD0//- " DN0 000 DRVD00//- " DN00 PN: bar Pout:.- bar 0000 DRVD0/ " DN0 000 DRVD/ "/ DN 0000 DRVD0/ 3" DN DRVD00/ " DN00 00 DRVD/ " DN 000 DRVD0/ " DN DRVD00/ " DN00 Pout: - bar 000 DRVD0//- " DN0 000 DRVD//- "/ DN 000 DRVD0//- 3" DN0 000 DRVD00//- " DN00 00 DRVD//- " DN 00 DRVD0//- " DN0 000 DRVD00//- " DN00 Pout: - bar 000 DRVD0//- " DN0 000 DRVD//- "/ DN 000 DRVD0//- 3" DN0 000 DRVD00//- " DN00 00 DRVD//- " DN 00 DRVD0//- " DN0 000 DRVD00//- " DN00 PN: 0 bar Pout:.- bar 000 DRVD0/0 " DN0 000 DRVD/0 "/ DN 000 DRVD0/0 3" DN0 000 DRVD00/0 " DN DRVD/0 " DN 00 DRVD0/0 " DN0 Pout: - bar 000 DRVD0/0/- " DN0 000 DRVD/0/- "/ DN 000 DRVD0/0/- 3" DN0 000 DRVD00/0/- " DN DRVD/0/- " DN 00 DRVD0/0/- " DN0 Pout: - bar 000 DRVD0/0/- " DN DRVD/0/- "/ DN 000 DRVD0/0/- 3" DN0 000 DRVD00/0/- " DN DRVD/0/- " DN 00 DRVD0/0/- " DN0 Plug (ND 0 to 00) (ND to 00) Seal ip seal Seal ring Guide bushings Setting screw and lock nut Finish Nodular cast iron GS00- Nodular cast iron GS00- Brass Faced steel Epoxy resins (blue RA 0) TECNICA CARACTERISTICS Downstream pressure (outlet) Downstream pressure adjustment bar (ND00 only up to bar). to bar (standard) to bar (optional) to bar (optional) Clockwise rotation: increase in pressure Connections Flanged according to UNI3 (NP - - 0) ND00 only NP and NP Pressure gauge connections G / " ND0 to ND (upstream and downstream) G 3/" ND0 to ND00 Max. operating temperature 0 C
7 Overall dimensions (mm) - diagram DRVD [ bar] 0, 0, 0, 0, 0, DN00 DN0 DN DN00 DN0 DN DN0, [ l/min] B PN B PN B PN Key:.. 3. Plug. Seal.. Seal ring. Guide bushings. ip seal. Setting screw 0. screws
series 5350 5351 Materials Body: 1/2, 3/4 and 1 : dezincification resistant alloy brass EN 12165 CW617N
Pre-adjustable pressure reducing valves with self-contained cartridge - series CCREDITED ISO 9 FM ISO 9 No. CLEFFI / GB replaces / GB Function Pressure reducing valves are devices which, when installed
More informationPRESSURE REDUCER AND RELIEF VALVES WITH METALLIC BELLOW FOR WATER STEAM
PRESSURE REDUCER AND RELIEF VALVES WITH METALLIC BELLOW FOR WATER STEAM PRESSURE REDUCER AND RELIEF VALVES These devices are used to reduce and control a gaseous flow pressure (air, steam, gas ). The PRESSURE
More informationSelf-operated Pressure Regulators Universal Pressure Reducing Valve Type 41-23
Self-operated Pressure Regulators Universal Pressure Reducing Valve Type 41-23 Application Pressure regulators for set points from 5 mbar to 28 bar Valves in nominal sizes DN 15 to 100 Nominal pressures
More informationAUTOMATIC AIR VENT VALVES MANUAL VALVES FOR DISCHARGING AIR FROM RADIATORS
01B101-GB AUTOMATIC AIR VENT VALVES MANUAL VALVES FOR DISCHARGING AIR FROM RADIATORS MAIN FEATURES ADVANTAGE OF BUILT-IN MANUAL DISCHARGE - Provision for controlling operation of the automatic discharge
More informationPRESSURE REDUCING CONTROL VALVE
Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING CONTROL VALVE with LOW FLOW BY-PASS FEATURE Main Line
More informationMustang Series PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE. M115-2 (Globe) M1115-2 (Angle) Schematic. Standard Components
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Throttles to maintain minimum upstream pressure PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE
More informationTHERMOSTATIC ACTUATORS WITH LIQUID-FILLED SENSITIVE ELEMENTS AND TEMPERATURE LOCKING
0A-GB THERMOSTATIC ACTUATORS WITH LIQUID-FILLED SENSITIVE ELEMENTS AND TEMPERATURE LOCKING SERIES SD - CD - GA MAIN CHARACTERISTICS - Available in the versions: Standard With Remote Sensor With Remote
More informationPressure reducing valves. Guide of applications
Pressure reducing valves Guide of applications CONTENTS 2 page The pressure reducing valve : Definition 3 Water savings 3 Pressure reducing valves or Regulators? 3 WATTS, the inventor of the regulator
More informationSelf-operated Temperature Regulators Temperature Regulator Type 1u
Self-operated Temperature Regulators Temperature Regulator Type u Application Temperature regulators for cooling installations Control thermostats for set points ) from 0 to 250 C G ½ to G or DN 5 to 50
More informationCRANE. Σελίδα 1 από 2. Dimensions and Weights. Weight (kg) Size
CRANE Σελίδα από 2 DM93 Variable Orifice Double Regulating Valve PN6 Cast Iron Balancing Valve (VODRV), Flanged to BSEN 92-2 The DM93 variable orifice double regulating valves will give satisfactory performance
More informationBERMAD Waterworks. Pressure Relief/Sustaining Valve. 700 Series. Model 730. Features and Benefits. Major Additional Features
Pressure Relief/Sustaining Valve Prioritizing pressure zones Ensuring controlled pipeline fill-up Preventing pipeline emptying Pump overload & cavitation protection Safeguarding pump minimum flow Excessive
More information4/2-Way Pneumatic Solenoid Valve
4/2-Way Pneumatic Solenoid Valve Robust servo assisted piston valve Service friendly manual override Single or block assembly Explosion-proof versions Type 5413 cam be combined with Type 2508 Cable plug
More information4. Combi valves. 7. Fire hydrants. 8. Check valves. 9. Air valves
1. General company and product information 2. Flanged gate valves for water 3. Other gate valves for water 4. Combi valves 5. Service connection valves for water 6. Valves and fittings for gas 7. Fire
More informationPressure reducing valve, direct operated, Type ZDR 6 D
RE 26 57/2.3 Replaces:.2 Pressure reducing valve, direct operated, ype ZDR 6 D Nominal size 6 Series 4X aximum operating pressure 2 bar aximum flow 5 L/min K 4279/ ype ZDR 6 DP2 4X/ Y Overview of contents
More informationSeated valves (PN 16) VF 2 2-way valve, flange VF 3 3-way valve, flange
Seated valves (PN 16) VF 2 2-way valve, flange VF 3 3-way valve, flange Description VF 2 VF 3 VF 2 and VF 3 valves provide a quality, cost effective solution for most water and chilled applications. The
More informationTypes 66R and 66RR Low-Pressure Relief Valves
November 2009 Types 66R and 66RR Low-Pressure Relief Valves W1953 W1908 TYPE 66R RELIEF VALVE TYPE 66RR RELIEF VALVE Figure 1. Typical Constructions Introduction Types 66R and 66RR low-pressure throttling
More informationFlow controller with integrated control valve (PN 16, 25, 40*) AFQM, AFQM 6 - return and flow mounting
Data sheet Flow controller with integrated control valve (PN 16, 5, 40*) AFQM, AFQM 6 - return and flow mounting Description AFQM 6 DN 40, 50 AFQM DN 65-15 AFQM DN 150-50 AFQM(6) is a self-acting flow
More information1805 Series Relief Valves
October 2011 1805 Series Relief Valves P1026 1805G Type 1805-2 Type 1805-4 Figure 1. Typical 1805 Relief Valves Introduction The 1805 Series relief valves are designed for use in farm tap applications
More informationProduct Manual. CVS Type 67AFR Filter Regulator. Introduction. Installation. Description
Product Manual CVS Type 67AFR Filter Regulator Introduction This CVS Controls product manual includes instructions for the installation, adjustment, maintenance and parts ordering of the CVS Type 67AFR
More informationS GATE KNIFE GATE VALVE WITH PNEUMATIC ACTUATOR
MAIN FEATURES The pneumatic S GATE knife gate valve is intended for the automatic shut off of pipes of the heavy fluids like slurries and powders. The main fields of application are the water treatment,
More information3/2-way Mini Solenoid Valve
3/2way Mini Solenoid Valve Directacting 0... bar DN mm... DN mm,,, subbase, banjobolt connection 21mm coil spacing when mounted on manifold Type can be combined with... Type 20 Type 207 Type able plug
More informationPipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
More informationType 3353 Angle Seat Valve
Type 3353 Angle Seat Valve Application On/off valve with pneumatic piston actuator Nominal size DN 15 to 50 (NPS ½ to 2) Nominal pressure PN Temperature range 10 to 180 C Globe valve with an angle seat
More informationBERMAD Waterworks. Quick Active Check Valve. 700 Series. Model 740Q. Features and Benefits. Major Additional Features
Booster Pump Control Valve Quick Active Check Valve Isolates system from the effects of pump starts and stops for: Solitary single speed pumps Battery of single speed pumps (add & switch) Battery of variable
More informationPilot Operated Pressure Reducing Valve PRV 47 (Steel) PRV47I (St.Steel)
OPTIONS: USE: AVAILABLE MODELS: Pilot Operated Pressure Reducing Valve PRV 47 (Steel) PRV47I (St.Steel) DESCRIPTION The ADCA PRV47 pilot operated pressure reducing valves are designed for use on steam,
More information1800C and 1800C-HC Series Service Regulators. Technical Bulletin
and -H Series Service Regulators Technical Bulletin and -H Series Service Regulators 0 Elster American Meter The Series pressure regulators are designed to control natural gas, air, nitrogen, carbon dioxide,
More information1.1 Z 011-A WAFER PATTERN BUTTERFLY TYP Z 011-A TECHNICAL DATA
WAFER PATTERN BUTTERFY TYP Z 0-A TECNICA DATA A universally applicable wafer type valve acc. to EN 3. The large variety of basic materials allows applications in different industries. Nominal diameter:
More informationAssisted lift operated 2/2-way solenoid valves Type EV250B
MAKING MODERN LIVING POSSIBLE Data sheet Assisted lift operated 2/2-way solenoid valves Type EV250B EV250B with assisted lift can operate from zero and up to 10 bar differential pressure. This 2/2-way
More informationWATER PRESSURE REDUCING VALVES
MADE IN THE USA WATER PRESSURE REDUCING VALVES TABLE OF CONTENTS PRODUCT PAGE How Pressure Reducing Valves Work 3 36 Series 4 36C Series 6 36H Series 8 AUTOMATIC PRESSURE REDUCTION Pressure reducing valves
More informationAPI Flanged Safety Relief Valves Series 526 CATALOG
API Flanged Safety Relief Valves Series 26 CATALOG The-Safety-Valve.com 1 Valve finder How to find the right product group High operating to set pressure ratio, high backpressure or low total height? Yes
More information2-Port Self-acting Temperature Control Valve Selection for Heating and Cooling Applications
Page 1 of 12 TI-S21-07 CH Issue 1 Cert. No. LRQ 0963008 ISO 9001 2-Port Self-acting Temperature Control Valve Selection How to select a system Valve selection: 1. Is the application for heating or cooling?
More informationType 92S Pilot-Operated Steam Regulator
Type 92S Pilot-Operated Steam Regulator Introduction The Type 92S steam regulator is piston actuated for high cycle steam service which includes a Type 6492L, 6492H or pilot (see Figure 1). These pilots
More informationPressure regulating valve with modulating kit, type DRV
Operation Installation and Maintenance Instructions Pressure regulating valve with modulating kit, type DRV hp-technik GmbH Industriepumpen-Förderaggregate und Anlagenbau Gablonzer Straße 21 D-76185 Karlsruhe
More informationZOP, ZOT SIGMA PUMPY HRANICE GEAR PUMPS 426 1.99 21.04
SIGMA UMY HRANICE GEAR UMS SIGMA UMY HRANICE, s.r.o. Tovární 605, 753 01 Hranice, Czech Republic tel.: +420 581 661 111, fax: +420 581 602 587 Email: sigmahra@sigmahra.cz, 426 1.99 21.04 Application In
More informationAIR-AIR PRESSURE MULTIPLIER (BOOSTER)
AIR-AIR PRESSURE MULTIPLIER (BOOSTER) The air-air pressure multiplier, or booster, is an automatic device that compresses air to give an outlet pressure that is double the inlet pressure. It is normally
More information3/2-way Solenoid Valve, direct-acting, NC or NO
3/2-way Solenoid Valve, direct-acting, NC or NO Electrical connection cable plug, Form A With or without manual override as standard Threaded port and sub-base s Impulse optional Type 6014 can be combined
More informationSelf-operated Temperature Regulators Type 1 to Type 9. PN 16 to 40 Class 125 to 300 DN 15 to 250 NPS ½ to 10 G ½ to 1 Up to 350 C Up to 660 F
Self-operated Temperature Regulators Type 1 to Type 9 PN 16 to 40 Class 125 to 300 DN 15 to 250 NPS ½ to 10 G ½ to 1 Up to 350 C Up to 660 F Edition April 2012 Information Sheet T 2010 EN Self-operated
More informationT U R B I N E G A S M E T E R
TURBINE GAS METER TURBINE GAS METER CGT 1 2 3 4 5 6 7 Design and function page 2 General technical data page 3 Measurement outputs page 4 Dimensions and weights page 5 Performance page 7 Pressure loss
More informationMAKING MODERN LIVING POSSIBLE. Thermostatic valve AVTA. Technical brochure
MAKING MODERN LIVING POSSIBLE Thermostatic valve AVTA Technical brochure 2 IC.PD.500.A3.02-520B3728 Danfoss A/S 07-2009/ RA-MC/mr Contents Page Features............................................................................................4
More informationMODEL 201 225LP 225LP2 225LP4 Safety Relief Valves
Edition GDRV.06 BRYAN DONKIN RMG CANADA LIMITED Serving the Gas Industry WORLDWIDE Applications Specifically designed to protect the downstream system or equipment from over pressure conditions by discharging
More informationSPERRYN GAS CONTROLS DELTA FLUID PRODUCTS LIMITED
SPERRYN GAS CONTROLS DELTA FLUID PRODUCTS LIMITED Domestic and Non-Domestic Meter Regulators G940/G941 - Domestic Meter Regulator Domestic regulator offering high performance in a compact unit. Sizes:
More informationFilter Housing SG Standard
Page of 7 Filter Housing SG Standard The steel standard filter housings with econometer and pneumatic drain are designed for the purification of compressed air and gases. Due to the modular design of the
More informationSCP 012-130 ISO. Other advantages: SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics.
SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics. SCP 012-130 ISO covers the entire displacement range 12-130 cmᶟ rev. at a maximum pressure of
More informationREGULATORS 175/153 Series
175/153 Series 175 HEATING 153 COOLING Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2002 Watson McDaniel Company Revised 7/2002 175 / 153 Screwed
More informationRUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a wafer valve designed for a wide range of industrial applications. The double-seated design provides bi-directional shut off. The design of the valve
More informationMaterials : Cast iron body
Size : Ends : Min Temperature : Max Temperature : DN 50 to DN 500 Between flanges ISO PN10-10 C + 90 C Max Pressure : 10 Bars up to DN 200 Specifications : Non rising stem and handwheel Bidirectional tightness
More informationEWE Ball Valve-Type Tapping Valve. EWE Ball-Type Tapping Valve. EWE GBM Tapping Valves. for water and gas
The following overview shows the different EWE tapping valves to help you to make your choice: EWE valve tapping valve for vertical tapping with operating shut-off, for all types of pipe, with external
More informationSLAM-SHUT VALVE. Type OSE. Europe, Middle East, Africa and Asia Pacific Documents Only. Process Management TM
SLAM-SHUT VALVE Type OSE Process Management TM DESCRIPTION The purpose of the OSE slam shut valve is to totally and rapidly cut off gas flow when the outlet pressure exceeds or drops below the setting.
More informationVdS 2100-09en. VdS Guidelines for water extinguishing systems. Non-return valves. Requirements and test methods. VdS 2100-09en : 2011-05 (01)
VdS Guidelines for water extinguishing systems VdS 2100-09en Requirements and test methods VdS 2100-09en : 2011-05 (01) Publishing house: VdS Schadenverhütung GmbH Amsterdamer Str. 172-174 50735 Köln,
More informationThermostatic actuator RAVV - for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16)
- for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16) Description RAVV can be combined with 2-way valves RAV- /8, VMT-/8 or VMA 15. Controller closes on rising temperature. There is a special
More informationBERMAD Waterworks. Pressure Reducing Valve. 700 Series. Model 720. Features and Benefits. Major Additional Features
Pressure Reducing Valve Flow and leakage reduction Cavitation damage protection Throttling noise reduction Burst protection System maintenance savings The Pressure Reducing Valve is a hydraulically operated,
More informationAutomatic Bypass Control AVDO
Application AVDO is a self-acting constant flow control primarily used either to maintain minimum flow rates through e.g. a low-capacity gas boiler or to control the differential pressure in a central
More information3/2-way pneumatic cartridge solenoid valve
3/2-way pneumatic cartridge solenoid valve Compact design with 11 mm width per station Orifices from 0.5 mm (9 bar) to 1.2 mm (1.5 bar) High durability and reliability Low power consumption, as well as
More informationThermostatic actuator RAVK - for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16) - for 3-way valves KOVM (PN 10), VMV (PN 16)
- for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16) - for 3-way valves KOVM (PN 10), VMV (PN 16) Description RAVK can be combined with: - 2-way valves RAV-/8, VMT-/8, VMA, or - 3-way valves
More informationPRESSURE REGULATOR SERIES 2100-4100 - 5100 R 4100 R 2100 R 5100 VIRTUAL CATALOGUE FAIL TO OPEN REGULATOR BALANCED VALVE HIGH FLOW COEFFICIENT
VIRTUAL CATALOGUE FAIL TO OPEN REGULATOR BALANCED VALVE HIGH FLOW COEFFICIENT PRESSURE REGULATOR WIDE PRESSURE-REGULATION RANGE CAN BE SUPPLIED WITH MINIMUM / MAXIMUM PRESSURE SLAM-SHUT VALVE R 4100 POSSIBILITY
More informationSystem 8. ü www.nassmagnet.com ( +49 511 6746-0. System 8
System 8 ü www.nassmagnet.com ( +9 11 7-0 System 8 The name System 8 stands for a modular system of solenoid coils, armature systems, solenoid operators and solenoid valves. The diameter of the armatures
More informationIndex 11.1. Page. Pumping Systems...11.2-11.4 Intensifiers...11.5 Gas Boosters...11.6-11.7 High Pressure Generators...11.8-11.9
Pumping Systems, Intensifiers, Gas Boosters and High Pressure Generators High Pressure Equipment Company produces a number of components and systems for general industrial, elevated pressure applications.
More informationORLANDO srl. M P R 50 025 OPTIMA Radial pressure gauges for swimming-pools 0-2,5 Bar
Chiavari (Ge) - Italia Tel.: Italia + 0185 + 38.50.10 Fax: Italia + 0185 + 38.50.11 e-mail: orlando@orlando.it Http://www.orlando.it M R 50...: Radial pressure gauge ø 50 ( available scale in bar: 4, 6,10,12,16
More informationThermostatic actuator RAVK - for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16) - for 3-way valves KOVM (PN 10), VMV (PN 16)
- for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16) - for 3-way valves KOVM (PN 10), VMV (PN 16) Description RAVK can be combined with: - 2-way valves RAV-/8, VMT-/8, VMA, or - 3-way valves
More informationHow To Use A Flowmeter
INLINE flowmeter for continuous flow measurement Economic integration in pipe systems without any additional piping 3-wire frequency pulse version to directly interface with PLC s (both PNP and NPN) Connection
More informationCommercial & Industrial Propane Regulators and Meters
Commercial & Industrial Propane Regulators and Meters Master Distributor for First Stage Regulators P32* Field adjustable 60 Mesh screen on inlet 1/4 FNPT 250 PSI Excellent stability P37* Patented balance
More informationTYPE E Main Valve Sizes 3 /8 through 12
SD 3001F PRINTED IN U.S.A. SD 3001F/0707 A B TYPE E MAIN VALVE C D E TYPE E Main Valve Sizes 3 /8 through 12 The Spence Type E Main Valve is of normally closed, single seat design featuring packless construction,
More information2-way flow control valve Type 2FRM 6
RE /0.0 Replaces:.0 -way flow control valve Type FRM Nominal size Series X Maximum operating pressure bar ) Maximum flow L/min ) When used in conjunction with a rectifier plate up to 0 bar H//D /97 + H//D
More informationThermostatic element RAVV for 2-way valves
Description / Application RAVV is a self-acting thermostatic element which can be combined with 2-way valve bodies RAV-/8, VMT-/8 or VMA 15. RAVV is used to control temperatures in small hot water cylinders
More informationOPERATING and MAINTENANCE MANUAL SERIES 2700A CONTROL VALVE CONTENTS. INTRODUCTION...1 Scope...1 Description...1 Valve Identification...
OPERATING and MAINTENANCE MANUAL SERIES 2700A CONTROL VALVE CONTENTS INTRODUCTION...1 Scope...1 Description...1 Valve Identification...2 1.0 VALVE INSTALLATION...2 2.0 VALVE MAINTENANCE...3 Actuator Disassembly...3
More informationRefrigeration and air conditioning Date: 10/2013
Catalogue 40 WEH Connectors for filling, evacuating and testing of refrigeration and air conditioning components Refrigeration and air conditioning Date: 10/2013 WEH - We Engineer Hightech All rights reserved,
More informationCoolflo Safe Touch Shower Mixing Valve ST20015CP
Coolflo Safe Touch Shower Mixing Valve ST20015CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot accept
More informationHigh CATALOG. LESER worldwide. Performance. Flanged Safety Relief Valves Series 441 Series 441 Full nozzle Series XXL Series 444 Series 458
LESER UK Bristol sales@leser.co.uk LESER Germany Hamburg and Hohenwestedt sales@leser.com André Ramseyer AG Flamatt, Switzerland info@ramseyer.ch LESER China Tianjin, Beijing, Shanghai and Shenzhen sales.china@leser.com
More informationUnit 24: Applications of Pneumatics and Hydraulics
Unit 24: Applications of Pneumatics and Hydraulics Unit code: J/601/1496 QCF level: 4 Credit value: 15 OUTCOME 2 TUTORIAL 1 HYDRAULIC PUMPS The material needed for outcome 2 is very extensive so there
More informationECOplus Solar Cylinder
TECHNICAL INFORMATION Solar Cylinder Wagner& Co Connection Options for CONVECTROL II The Effective Convection Brake Technically and fluidically optimized barriers separate the water cooled in the pipes
More informationThermostatic valve Type AVTA
MAKING MODERN LIVING POSSIBLE Data sheet Thermostatic valve Type AVTA Thermostatic valves are used for proportional regulation of flow quantity, depending on the setting and the sensor temperature. The
More informationThermostatic actuator RAVI - for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16) - for 3-way valves KOVM (PN 10), VMV (PN 16)
- for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16) - for 3-way valves KOVM (PN 10), VMV (PN 16) Description RAVI is self-acting thermostatic actuator primarily for use for temperature control
More informationV47 Series Temperature Actuated Modulating Water Valves
V47 Series Temperature Actuated Modulating Water Valves Master Catalog 125 Valves, Miscellaneous (Other Than Gas) Section V Product Bulletin V47 Issue Date 0286 Application The V47 modulating valves regulate
More informationAutomatic balancing valves ASV
Automatic balancing valves ASV ASV-P ASV-PV ASV-PV ASV-PV ASV-BD ASV-I ASV-M 15-40 15-40 50 65-100 15-50 15-50 15-50 Description / Application ASV balancing valves are used for dynamic hydronic balance
More informationRickmeier Solutions. Gear pumps for superior Lubrication
Rickmeier Solutions Gear pumps for superior Lubrication P U M P E N T E C H N O L O G I E #1. Introduction Position and significance of Rickmeier products Rickmeier supplies pumps, valves and systems for
More information3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics
3/2-, 5/2-5/3-way Solenoid Valves for process pneumatics Type 6518 stard High flow-rate capacity Reduced power consumption Single or manifold mounting stard Type 6518/6519 can be combined with... Stard-,
More informationTA-FUS1ON. Fully adjustable Kvs control and balancing valves. That s just two good.
TA-FUS1ON Fully adjustable Kvs control and balancing valves. That s just two good. Supported by the Reece hvac-r network. Through our 36 stores around Australia, Reece hvac-r is committed to supporting
More information3/2, 5/2, 5/2 bistable and 5/3 way pneumatic solenoid valve
3/2, 5/2, 5/2 bistable and 5/3 way pneumatic solenoid valve Type 6518 Type 6519 Type 6518/6519 can be combined with... Single or block mounting Suitable for outdoor and chemical atmospheres Suitable for
More informationSingle sub-base valve
solenoid valves Mini-valves 10 mm Electrical connection... Mounting... Port sizes... Rated temperature... Fluid... Working pressure... Nominal flow... Pneumatic connections Voltage... Power... NC poppet
More informationDuplex Filters 40 FLDK 0008(C)-0120(C)
Industrial Filters Accumulators Duplex Filters 40 FLDK 0008(C)-0120(C) Filters for inline installation for continuous operating Ball valve change over Optimised flow characteristics by 3D computer aided
More information820 NOVA mv THERMOPILE POWER SUPPLY THERMOELECTRIC SAFETY DEVICE SERVO-CONTROLLED PRESSURE REGULATOR SHUT-OFF SOLENOID VALVE.
SIT Group 820 NOVA mv MULTIFUNCTIONAL CONTROL FOR GAS THERMOPILE POWER SUPPLY THERMOELECTRIC SAFETY DEVICE SERVO-CONTROLLED PRESSURE REGULATOR SHUT-OFF SOLENOID VALVE PIN 3AP700/2 SINGLE-KNOB MULTIFUNCTIONAL
More informationSOLENOID VALVES AND PNEUMATIC VALVES
2 A S E R I E S Catalogue 2005-2006 Directly operated solenoid valves Series A 2/2 way, 3/2 way monostable, bistable (with magnetic memory) Ports M5,, cartridge ø4 The Series A solenoid valves are of the
More informationSeries 240 Type 3244-1 and Type 3244-7 Pneumatic Control Valves Type 3244 Three-way Valve
Series 240 Type 3244-1 and Type 3244-7 Pneumatic Control Valves Type 3244 Three-way Valve DIN and ANSI versions Application Mixing or diverting valve for process engineering and industrial applications
More informationBOWIE PUMPS OPERATION - MAINTENANCE
BOWIE PUMPS OPERATION - MAINTENANCE PUMPING PRINCIPLE: The meshing owieeof the gears cause a slight depression, with the resulting enmeshing of the gears causing a vacuum drawing the fluid being pumped
More informationSize : Ends : Min Temperature : Max Temperature : Materials : Cast iron body
Size : Ends : Min Temperature : Max Temperature : DN 32/40 to DN 1000 Between flanges GN10/16, ASA150 up to DN600-10 C + 110 C ( 130 C temporarily ) Max Pressure : 16 Bars up to DN300 Specifications :
More informationPneumatic Shut-off Butterfly Valve Type 3335/31a SRP or DAP
Pneumatic Shut-off Butterfly Valve Type 3335/31a SRP or DAP Application Tight-closing butterfly valve for process engineering and industrial applications DN 50 to 300 NPS 2 to 12 Nominal pressure PN 10
More informationShut-off & Lockout Valves 1/4" to 1-1/2" port size
Section 16 Shut-off & Lockout Valves 1/4" to 1-1/2" port size Contents T72 Excelon Shut-off & Lockout Valves 1/4", 3/8" Port Sizes....................................ALE-16-2 T73 Excelon Shut-Off & Lockout
More informationYELLOW JACKET Hose Adapters, Valves, and Parts right to the last detail
YELLOW JACKET Hose Adapters, Valves, and Parts right to the last detail NEW Valve core tool page 35 EXPANDED LINE Quick couplers page 36 33 1/4" 4-IN-1 BALL VALVE TOOL for vacuum, charge, cores and recovery
More informationINLINE SD-PUMPS WITH IEC-STANDARD MOTOR
INLINE SD-PUMPS WITH IEC-STANDARD MOTOR AT_-1/ Hz DN1 3 r/min min H G 1/ G 1/ 17 11 3xM, Depth 1 1 Ø1 Ø1 xø19 7 3xØ1 9 17 1 xø1 17 1 kw A kg H OKN-13 E1 F19 7. (9). 9 OKN-13 C1 F19. (.) 11. 1 9 OKN-1 E1
More informationFLOAT SWITCHES FLOW SWITCHES FOR LIQUIDS PRESSURE SWITCHES
01D351-GB FLOAT SWITCHES FLOW SWITCHES FOR LIQUIDS PRESSURE SWITCHES DOLOMIT FLOAT SWITCHES The DOLOMIT float switches find application in liquid level control in tanks and wells; they require connection
More informationHOPPER SHAPE KNIFE GATE VALVE
HOPPER SHAPE KNIFE GATE VALVE The model knife gate is a uni-directional wafer valve designed for industrial bulk handling service applications (powdered and granular products). The special design of the
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationQLM and QLD Series Three-port Control Valves
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
More information3/2, 5/2, 5/2 bistable and 5/3 way pneumatic solenoid valve
3/2, 5/2, 5/2 bistable and 5/3 way pneumatic solenoid valve Type 6518 Type 6519 Type 6518/6519 can be combined with... Single or block mounting Suitable for outdoor and chemical atmospheres Suitable for
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationHFS and HFD Series. High Flow Single and Duplex Filters Max. 11200 l/min. 10 bar. Heavy Duty Reliability. Applications: Contact Information:
High Flow Single and Duplex Filters Max. 11200 l/min. 10 bar Heavy Duty Reliability New High Flow Single and Duplex Filters ensure reliability in industrial, marine, and power generation applications up
More information1301 Series High-Pressure Regulators
1301 Series High-Pressure Regulators Bulletin 71.1:1301 December 2013 P10 Figure 1. Type 1301F Regulator Features Durable Stainless Steel Diaphragm For high-outlet pressure applications. Spare Valve Disk
More informationHose and Tube Fittings Series 1-3
Embracing Challenge Hose and Tube Fittings Series 1-3 out of plastics PP, PVDF, PTFE Series 1 Special Features Corrosion resistant Gas tight Easy to handle Different connection threads Application Hose
More informationDMP 331. Industrial Pressure Transmitter for Low Pressure. Stainless Steel Sensor
DMP Industrial Pressure Transmitter for Low Pressure Stainless Steel Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 / 0. % FSO from 0... 00 mbar up to 0... 40 bar Output signals
More informationAir Eliminators and Combination Air Eliminators Strainers
Description Air Eliminators and Combination Air Eliminator Strainers are designed to provide separation, elimination and prevention of air in piping systems for a variety of installations and conditions.
More information