Fiber Solutions Short Form Catalog

Fiber Solutions Short - TABLE OF CONTENTS Introduction...3 Fiber Optic Cable by LanPro...3 LanPro and Corning Optical Fiber Cables...3 Singlemode...3 Multimode...4 Cross reference Table...4 LanPro Fiber Cable Code...5 Cable Types...7 Example Ordering Codes...10 Selection Table...10 Standard Connectors...11 Common specification Table for the LanPro Fiber Optic Connectors...11 Connector Color Codes...11 Standard Optical Connectors Part Number Code...11 Standard Connector Types...12 ST Connectors...12 Example P/N s for ST Type Optical Connectors...12 FC Connectors...12 Example P/N s for FC/PC Type Optical Connectors...12 SC Connectors...13 Example P/N s for SC Type Optical Connectors...13 LC Connectors...13 Example P/N s for LC Simplex Type Optical Connectors...13 Example P/N s for LC DuplexType Optical Connectors...13 Example P/N s for LC/APC Simplex Type Optical Connectors...14 MTRJ Connectors...14 Example P/N s for MTRJ Female Type Optical Connectors...14 Example P/N s for MTRJ Male Type Optical Connectors...14 Field Connectors...14 Example P/N s for SC&ST Field Type Optical Connectors...15 Cutter Tool for Field Connector...15 Fiber Optic Patch Cord and Pigtails...15 Connector End-Face Preparation Polish Grades...15 SPECIFICATIONS...16 Patchcord and Pigtail part numbering code...17 Example P/N s for Fiber Optic Duplex Patchcords...17 Fiber Optic Adaptors...19 Fiber Optic Adaptor Code...19 Example P/N s for Optical Adaptors...20 Fiber Optic Wall Enclosures (Boxes) and FO Patch Panels...20 Fiber Optic Wall Enclosures(Boxes) and FO Patch Panels CODES...21 Fiber Optic Wall Enclosures(Boxes) Empty...21 Example P/N s for Optical Empty Wall Enclosure...22 Fiber Optic Rack Mounted Patch Panels Unloaded...22 Example P/N s for Empty Rack Mount Unloaded Patch Panels...22 24 Port Fiber Optic Rack Mounted Patch Panels Factory Loaded...22 Example P/N s for 24 Port Fiber Optic Rack Mounted Patch Panels Factory Loaded...23 Fiber Optic Adaptor Panel Modules...23 Fiber Optic Adaptor Panel Unloaded CODE...23 Fiber Optic Adaptor Panel Loaded CODE...25 Few Example P/N s for Adaptor modules for Empty Rack Mount Loaded Patch Panels...26 Tools for Fiber Optics...27 LPT-FKIT01...27 LPT-FSCOPE01...30 LPT-CS3B...30 Fiber Solutions Short Form Catalog

Fiber Solutions Short Form Catalog 1 INTRODUCTION LanPro has consolidated itself with a broad Portfolio of products under the concept of ONE STOP SOURCE (OSS) philosophy, and is becoming one of the most demanded brands by System Integrators. LanPro produces and distributes a broad line o Fiber Optic Products that as a whole constitute the LanPro Fiber Solution. It has been split in two major areas: First, our Fiber Optic System, which includes the paraphernalia of Connectors, Patch Cords and Pigtails, Adaptors, Termination/Patch Panels, Accessories and Instruments and second, the Fiber Optic Cables per se. LanPro is committed to continue improving and enhancing its broad line of products in its LanPro Fiber Solution so that our clients can enjoy the benefits of the application of proven technologies in the Optical Fiber systems of today and Tomorrow. 2 FIBER OPTIC CABLES BY LANPRO LanPro has partnered with several fiber manufacturers in the development of Optical Cables that are suited for the myriad of applications in the field. Optical Cables are composed of two main parts: the Optical Fiber cores, bought from widely recognized manufacturers and the Jackets that are designed to protect those cores and suit them for the application. We have selected the best fiber cores for our Optical Cables. We have included Corning optical fiber as a first option in a document explaining the Multi-Mode and the Mono-Mode versions available at this moment. LanPro can use other brands as the core fibers as per our client specifications when production quantities meet the business objectives. 2.1 LanPro, Corning Optical Fiber. Names that are synonymous with cable and fiber combine to create the ultimate in fiber optics. LanPro partners with Corning Optical Fiber to deliver the world s most reliable and technologically advanced optical fiber cables. 2.2 Singlemode. Standard LanPro utilizes Corning SMF-28e+ fiber as its standard singlemode offering. This is a full-spectrum fiber that is fully backward-compatible with legacy singlemode fiber. It enables increased optical launch power of legacy singlemode fiber, improved macrobend specifications from 0.05 db to 0.03 db, and tighter zero dispersion wavelength (λo) tolerance from a range of ± 10 nm to ± 7 nm. This fiber supports all broadband applications and complies with the most stringent industry standards, such as: ITU-T G.652 (Tables A, B, C and D). IEC 60793-2-50 Type B1.3. TIA/EIA 492-CAAB. Telecordia GR-20-CORE. Long-Haul For long-haul applications, rely on LanPro and the technology of Corning LEAF fiber. This is the most widely deployed non-zero dispersion shifted (NZ-DSF) fiber in the world and the first low water peak NZ-DSF fiber. Its large effective area and industry-leading polarization mode dispersion (PMD) specifications enable 10 Gb/s and 40 Gb/s network systems of the future. 3

ClearCurve ZBL Lanpro, utilizing Corning ClearCurve ZBL Optical Fiber, delivers the best macrobending performance in the industry while maintaining compatibility with current optical fibers, equipment, practices and procedures. This fullspectrum singlemode optical fiber, when subjected to smaller radii bends, experiences virtually no signal loss. ClearCurve fiber exceeds the most stringent bend performance requirements of ITU-T Recommendations G.657. B3 while remaining fully compliant with ITU-T Recommendation G.652.D and the installed base of Corning SMF-28e and SMF-28e+ fiber. 2.3 Multimode. ClearCurve Multimode Fiber Corning ClearCurve ultra-bendable laser-optimized multimode optical fiber delivers the best macrobending performance in the industry while maintaining compatibility with current optical fibers, equipment, practices and procedures. ClearCurve OM3/OM4 multimode fiber is designed to withstand tight bends and challenging cable routes with substantially less signal loss than conventional multimode fiber. These fibers have superior measurement technology and manufacturing control, and industry-leading CPC coatings for superior microbend and environmental performance. ClearCurve fiber performance is ensured by minembc, the industry s leading standards-approved bandwidth measurement for OM3 fibers. ClearCurve fibers are the only ones to use this measurement to ensure 10 Gb/s performance. 62.5 micron These fibers support data rates of 1 Gb/s in both the 850 nm and 1300 nm windows. They comply with the most stringent industry standards, such as: ISO/IEC 11801, type OM1 fiber. IEC 60793-2-10, type A1b fiber. TIA/EIA, 492AAAA-A. Fiber Solutions Short Form Catalog 50 micron These fi bers support data rates of 10 Gb/s at 850 nm. They also comply with the most stringent industry standards, such as: ISO/IEC 11801, type OM2, OM3 and OM4* fibers. IEC 60793-2-10, type A1a.1, A1a.2 and A1a.3* fibers. TIA/EIA, 492AAAB, 492AAAC-A and 492AAAD. * Assumes IEC draft standard is harmonized with 492AAAD, which was approved by TIA. 2.4 Cross Reference Table. Fiber Type LanPro Corning OpticalFiber Standard Loose Tube SM ZC SMF-28e+ Fiber Performance Loose Tube SM ZB SMF-28e+ Fiber Tight Buffer SM ZE SMF-28e+ Fiber Long-Haul SM ZE LEAF Fiber Ultra-Bendable SM ZA ClearCurve ZBL 62,5 um MM QG 62,5 um MM QL Infi nicor 300 Fiber Infi nicor CL 1000 Fiber Description Full spectrum, low water peak singlemode, ITU-T G.652D Full spectrum, high performance low water peak singlemode with 0.35/0.25 attenuation, ITU-T G.652D Full spectrum, low water peak singlemode with 900um PVC buffer, ITU-T G.652.D Large Aeff, low water peak, NZ-DSF singlemode, ITU-T G.655 Full spectrum with best macrobending performance, ITU-T G.652.D and ITU-T G.657.A 1 Gb/s _< 300 m at 850 nm, OM1* 1 Gb/s _< 550 m at 1300nm 1 Gb/s _< 500 m at 850 nm, OM1* 1 Gb/s _< 1000 m at 1300nm 4

Fiber Solutions Short Form Catalog Fiber Type LanPro Corning OpticalFiber Ultra-bendable 50 um MM BI ClearCurve OM2 Fiber Ultra-bendable 50 um MM TP ClearCurve OM3 Fiber Ultra-bendable 50 um MM TG ClearCurve OM4 Fiber Ultra-bendable 50 um MM TI ClearCurve OM4 Fiber *Designation per ISO 11801 Fiber Standards. 2.5 LanPro Fiber Cable Code. 2.5.1 Series Type. LP-OCJJSSCCCBFF LP-OC JJ SS CCC B FF Description 10 Gb/s _< 150 m at 850 nm, OM2* 1 Gb/s _< 750 m at 850nm 10 Gb/s _< 300 m at 850 nm, OM3* 1 Gb/s _< 1000 m at 850nm 10 Gb/s _< 550 m at 850 nm, OM4* 1 Gb/s _< 110 m at 850 nm 10 Gb/s _< 600 m at 850 nm, OM4+* 1 Gb/s _<1100 m at 850nm LanPro Fiber Optic. Series Type. Jacket Suffix. Fiber Count. Buffer Construction. Fiber Type. JJ Outdoor/Indoor. 05 Loose Tube Single Jacket with FRP central strength member. 06 Loose Tube Single Jacket Armored. 09 Loose Tube Single Jacket Ribbon Cable. 11 Toneable Flat Drop Cable. 13 Compact Central Loose Tube Drop Cable. 14 Central Tube Single Jacket Armored. 15 Loose Tube Single Jacket with Steel Wire/Stranded Central Strength Member. 16 Loose Tube Single Jacket Light Armored Steel Wire/Stranded Central Strenght Member. 17 Loose Tube Single jacket Light Armored with FRP Central Strenght Member and Laminated Aluminum Tape. 40 Tight Buffer Distribution Riser Cable. 41 Tight Buffer Distribution Plenum Cable. 42 Loose Tube Dual Jacket Armored LSZH. 43 Loose Tube Double Jacket Riser-Chemical-Resistant. 44 Loose Tube Single Jacket Plenum. 45 Loose Tube Single Jacket Riser. 46 Loose Tube Single Jacket LSZH. 47 Loose Tube Single Jacket Indoor/Outdoor with laminated aluminum tape. 48 Central Tube Single Jacket Plenum. Direct Buried. 02 Loose Tube Dual Jacket Armored with central steel wire/strand. 03 Loose Tube Dual Jacket Armored with FRP central strength member. Direct Buried with armor. 01 Loose Tube Triple Jacket Dual Armor. 04 Loose Tube Dual Jacket Dual Armor. 18 Loose Tube Single jacket Armored with Metallic Central Strenght Member and Laminated Aluminum Tape. 19 Loose Tube Single jacket Armored with FRP Central Strenght Member and Laminated Aluminum Tape. 5

Duct, Direct Buried or Aerial. 20 Loose Tube Single Jacket Armored cable with Two steel wires strength member and Laminated Steel Tape. Aerial Self Supporting. 07 08 Loose Tube Single Jacket Armored Self-Supporting Figure 8 with central steel wire, messenger wire and laminated aluminum tape for strength. Type 08 (Loose Tube Single Jacket Self Supporting Figure 8 with central steel wire, messenger wire and laminated aluminum tape for strength. 12 Mini (Figure 8) Drop Cable. 21 Loose Tube Single PE Jacket with Layer of Galvanized steel wires strength member. Aerial Outdoor. 22 Loose Tube Single PE Jacket with bonded Steel Tape with Layer of Galvanized steel wires strength member and wrapping. Aerial For Power Line. 10 All Dielectric Self Supporting ADSS. Indoor. 25 Tight Buffer Distribution PVC Cable. 26 Tight Buffer Breakout Plenum cable. 27 Tight Buffer Breakout Riser cable. 28 Tight Buffer Distribution Riser cable. 29 Tight Buffer Distribution Plenum. 30 Tight Buffer Distribution LSZH. 2.5.2 Jacket Suffix. Fiber Solutions Short Form Catalog 00 Black Jacket (UV Resistant). 01 Gel Water Block Cable Core. 02 Dry Tube. 03 Interlock Armor Plenum Steel. 04 Interlock Armor Plenum Aluminum. 05 Interlock Armor Plenum Steel w/sub-units. 06 Interlock Armor Plenum Aluminum w/sub-units. 07 Interlock Armor Riser Steel. 08 Interlock Armor Riser Aluminum. 09 Interlock Armor Riser Steel w/sub-units. 10 Interlock Armor Riser Aluminum w/sub-units. 11 Ripcord. 11 Dry Water Block Cable Core. SS SS 2.5.3 Fiber Count. CCC 1-144 2.5.4 Buffer Construction. 1 Tight Buffer. 2 Quick Strip. 3 Single Fiber Loose Tube(Gel Filled). 4 Multi-fiber loose Tube(Gel- Filled). 5 Loose Buffer. 6 Bare/Ribbon. B 6

Fiber Solutions Short Form Catalog 2.5.3 FF Fiber Type. Fiber Type LanPro Corning Optical Fiber Description Standard Standard Loose Tube SM Performance Loose Tube SM ZC ZB SMF-28e+ Fiber SMF-28e+ Fiber Tight Buffer SM ZE SMF-28e+ Fiber Long-Haul SM ZG LEAF Fiber Ultra-Bendable SM ZA ClearCurve ZBL 62.5 μm MM QG InfiniCor 300 Fiber 62.5 μm MM QL InfiniCor CL 1000 Fiber Ultra-bendable 50 μm MM Ultra-bendable 50 μm MM Ultra-bendable 50 μm MM Ultra-bendable 50 μm MM BI TP TG TI ClearCurve OM2 Fiber ClearCurve OM3 Fiber ClearCurve OM4 Fiber ClearCurve OM4 Fiber Full spectrum, low water peak singlemode, ITU-T G.652.D Full spectrum, high performance low water peak singlemode with 0.35/0.25 attenuation, ITU-T G.652. D Full spectrum, low water peak singlemode with 900μm PVC buffer, ITU-T G.652.D Large Aeff, low water peak, NZ-DSF singlemode, ITU-T G.655 Full spectrum with best macrobending performance, ITU-T G.652.D and ITU-T G.657.A 1 Gb/s _< 300 m at 850 nm, OM1* 1 Gb/s _< 550 m at 1300 nm 1 Gb/s _< 500 m at 850 nm, OM1* 1 Gb/s _< 1000 m at 1300 nm 10 Gb/s _< 150 m at 850 nm, OM2* 1 Gb/s _< 750 m at 850 nm 10 Gb/s _< 300 m at 850 nm, OM3* 1 Gb/s _< 1000 m at 850 nm 10 Gb/s _< 550 m at 850 nm, OM4* 1 Gb/s _< 1100 m at 850 nm 10 Gb/s _< 600 m at 850 nm, OM4+* 1 Gb/s _< 1100 m at 850 nm B1.3 ( G652D) P IEC 60793-2-10 Type A1b IEC 60793-2-10 Type A1a *SMF-28e+ is a trademark and Corning, LEAF, InfiniCor and Plus Corning Optical Fiber are registered trademarks of Corning Incorporated, Corning, NY, U.S.A. 2.6 Cables Types. 7

Outdoor/Indoor Usable in Duct or Aerial. Long-haul communication systems. Junction communication systems. Subscriber network systems. Local area network systems. The LP-OC05XX is completely dielectric and usable in areas with high incidence of lightning or in the vicinity of power lines or plants. LP-OC47XX Loose Tube Single Jacket Fiber Optic Cable, with Laminated Aluminum Tape and FRP Strength Member Typical Cross-Section Optical Fiber Jelly Compound Loose Tube Filling Compound Laminated Aluminum Tape PE Outer Sheath Wrapping Aramid Yarns FRP Possible Underlay Possible Filler Waterproof Tape (Only For Designation 98~144) LP-OC05XX Loose Tube Single Jacket Optical Fiber Cable. Typical Cross-Section Optical Fiber Jelly Compound Loose Tube Filling Compound Peripheral Strength Component(aramid yarns) PE Sheath Central Strength Member(FRP) Possible Underlay Possible Filler LP-OC17XX Loose Tube Single PE Jacket Fiber Optic Cable, with Light Armor, and FRP Strength Member. Typical Cross-Section Optical Fiber Jelly Compound Loose Tube Filling Compound Corrugated Steel Tape PE Outer Sheath Wrapping Aramid Yarns FRP Possible Underlay Possible Filler Waterproof Tape LP-OC16XX Loose Tube Single Jacket Mettallic Strenght Member Fiber Optic Cable. Typical Cross-Section Optical Fiber Jelly Compound Loose Tube Filling Compound Corrugated Steel Tape PE Outer Sheath Wrapping Steel Wire/Strand Possible Underlay Waterproof Tape Possible Filler LP-OC15XX Loose Tube Single Jacket Mettallic Strenght Member Fiber Optic Cable. Typical Cross-Section Optical Fiber Jelly Compound Loose Tube Filling Compound Laminated Aluminum Tape PE Outer Sheath Wrapping Steel Wire/Strand Possible Underlay Waterproof Tape(Only For Designation 98~144) Possible Filler Fiber Solutions Short Form Catalog Direct Buried Usable in Direct burial or Aerial. Long-haul communication system. Junction communication systems. Subscriber network systems. Local area network systems. Protected against rodent or termite attack. LP-OC02XX Loose Tube Dual Jacket Armored Fiber Optic Cable with central steel wire / strand. Typical Cross-Section Optical Fiber Jelly Compound Loose Tube Filling Compound PE inner Sheath Waterproof Yarns Corrugated Steel Tape PE Outer Sheath Steel Wire/Strand Possible Underlay Possible Filler LP-OC03XX Loose Tube Dual Jacket Armored Optical Fiber Cable. Typical Cross-Section Optical Fiber Jelly Compound Loose Tube Filling Compound PE Inner Sheath Aramid Yarns Waterproof Yarns Corrugated Steel Tape PE Outer Sheath FRP Possible Underlay Possible Filler Direct Buried with armor Usable in Direct burial. Long-haul communication system. Junction communication systems. Subscriber network systems. Local area network systems. Extra protection with laminated aluminum additional to the corrugated steel tape. LP-OC18XX Loose Tube Dual Jacket Armored Optical Fiber Cable with central steel wire / strand cable and Laminated Aluminum. Typical Cross-Section Optical Fiber Jelly Compound Loose Tube Filling Compound Laminated Aluminum Tape PE inner Sheath Waterproof Yarns Corrugated Steel Tape PE Outer Sheath Steel Wire/Strand Possible Underlay Possible Filler LP-OC19XX Loose Tube Dual Jacket Armored Fiber Optic Cable with FRP central strenght member and Laminated Aluminum Tape. Optical Fiber Jelly Compound Loose Tube Filling Compound Laminated Aluminum Tape PE Inner Sheath Aramid Yarns Waterproof Yarns Corrugated Steel Tape PE Outer Sheath FRP Typical Cross-Section Possible Underlay Possible Filler Duct, Direct Buried or Aerial Usable for ducts, direct burial, aerial installation. Long-haul communication system. Subscriber network systems. Local area network systems. LP-OC20XX Loose Tube Single Jacket Armored Optical Cable with two steel wires strength member and Laminated Steel Tape. Optical Fiber Jelly Compound Loose Tube Steel Wire Waterproof Tape Steel Tape Typical Cross-Section PE Sheath 8

Fiber Solutions Short Form Catalog Aerial Self Supporting Usable for aerial installation. Long-haul communication systems. Subscriber network systems. Local area network systems. LP-OC07XX Loose Tube Single Jacket Armored Self Supporting Figure 8 Fiber Optical Cable with central steel wire, messenger wire and laminated aluminum tape for strength. Typical Cross-Section Aerial Outdoor Messenger Wire Optical Fiber Jelly Compound Loose Tube Filling Compound Laminated Aluminum Tape PE inner Sheath Waterproof Yarns Corrugated Steel Tape PE Outer Sheath Steel Wire/Strand Possible Underlay Possible Filler Usable for direct burial or aerial installation. Long-haul communication systems. Subscriber network systems. Local area network systems. LP-OC08XX Loose Tube Single Jacket Supporting Figure 8 Optical Cable with central steel wire, messenger wire and laminated aluminum tape for strength. Typical Cross-Section Messenger Wire Optical Fiber Jelly Compound Loose Tube Filling Compound Laminated Aluminum Tape PE Outer Sheath Wrapping Steel Wire Possible Underlay Waterproof Tape (Only For Designation 98~144) Possible Filler LP-OC22XX Loose Tube Single PE Jacket Fiber Optic Cable with Layer of Galvanized steel wires strength member. Optial Fiber Jelly Compound Loose Tube Steel Wire Typical Cross-Section LP-OC21XX Loose Tube Single PE Jacket Fiber Optic Cable with Layer of Galvanized steel wires strength member. Typical Cross-Section Filling Compound Wrapping Steel Tape Waterproof Tape PE Sheath Optical Fiber Jelly Compound Loose Tube Steel Wire Filling Compound PE Outer Sheath Aerial For Power Line ADSS Usable on Power Lines. Pole-to-pole or pole-to premises. LP-OC10XX Loose Tube Single Dual Jacket All Dielectric Self Supporting Fiber Optical Cable with central FRP Strenght Member and peripheral Aramid Yarns cable. (ADSS). Typical Cross-Section Optical Fiber Jelly Filled Loose Tube Water Blocking FRP Strength Member Inner Sheath Aramid Yarns Outer Sheath Possible Filler Indoor Used in indoor cabling. FTTH Cable (Fiber to the home). Inter-building voice or data communication backbone. Installed in ducts, underground conduit or aerial/lashed. As connecting soft cable along walls, ceiling, layers and tubes. As pigtail of communication equipment. As moveable connecting cable and patchcord. LP-OC25XX Indoor Tight Buffer Distribution PVC Fiber Optic Cable. Tight buffer fiber Aramid yarn PVC Jacket 9

2.7 2.8 Example ordering codes. Item Jacket Fiber 1 Loose Tube Dual Jacket Armored Cable, Corrugated Steel Tape. 2 Loose Tube Single Jacket. 3 4 Tight Buffer Distribution PVC Cable. Loose Tube Dual Jacket Armored Cable, Corrugated Steel Tape. Selection Table. 62.5um IEC 60793-2-10 Type A1b, MM 62.5um IEC 60793-2-10 Type A1b, MM 62.5um IEC 60793-2-10 Type A1b, MM Fiber Count Model 8 LP-OC03010084QL 4 LP-OC05010044QL 4 LP-OC25010041QL ITU-T G.652.D/B1.3, SM 8 LP-OC03010084ZC Printing on outer Sheat LANPRO OPTICAL FIBER P/N: LP-OC03010084QL 8F MM -62.5/125- A1b- LOT-110301 WWW.LANPRO.COM *** M LANPRO OPTICAL FIBER P/N: LP-OC05010044QL 4F MM -62.5/125- A1b -LOT-110301 WWW.LANPRO.COM *** M LANPRO OPTICAL FIBER P/N: LP-OC25010041QL 4F MM -62.5/125- A1b- LOT-110301 WWW.LANPRO.COM *** M LANPRO OPTICAL FIBER P/N: LP-OC03010064ZC 8F SM -9/125- G.652.D LOT-110301 WWW.LANPRO.COM *** M Fiber Solutions Short Form Catalog LanPro Optical Cable Types Selection Table Strenght Member Made of Galvanized Steel Loose Tube Structure Tight Buffer Strenght Member Made of Fiber Reinforced Plastic (FRP) Distribution Breakout Non Armored Applications Non Light Heavy Plain Plenum Riser LSZH ser Riser Chemical Res. Light Armored Heavy PVC Armored Armored Armored Armored Armored Armored Plenum Ri- LSZH Riser Plenum 5.1 Outdoor/ Indoor 5.2. Direct Buried 5.3. Direct Buried with armor 5.4. Duct, Direct Buried or Aerial 5.5. Aerial Self Supporting 5.6 Aerial Outdoor 15 16 5,9 44 45 46 48 17,47 6,14,42 41 40 2 3 18 19 1,4 20 8 21 7 22 5.7 Aerial For Power Line 10 5.8 Indoor 25 29 28 30 27 26 10

Fiber Solutions Short Form Catalog 3 STANDARD CONNECTORS. LanPro manufactures and supplies several types of fiber Optic Connectors: ST, FC/PC Typical and One Piece, SC Typical, SC One Piece, FC/APC Typical, SC/APC Typical, SC Duplex Typical, and SC Duplex One Piece, all made to the most demanding standards in the industry. A choice of tools is also available for the crimping and termination of them. 3.1 Common specification table for the LanPro Fiber Optic Connectors. Specification Parameter Condition Multimode Singlemode Insertion Loss λ=1300 nm <0.5dB <0.5dB Return Loss PC Polish NA >35dB SPC Polish NA >40dB UPC Polish NA >50dB APC Polish NA >65dB Operation Temperature -20ºC to +70ºC 0.2dB 0.2dB Durability 500 cycles 0.2dB 0.2dB Vibration 10 to 55 Hz 1.5mm double amplitude 0.2dB 0.2dB Temperature Cycle -20ºC to +80ºC 0.2dB 0.2dB Tensile Strenght 10kgf 0.2dB 0.2dB 3.2 Connector Color Codes. Since the earliest days of fiber optics, orange, black or gray was multimode and yellow single mode. However, the advent of metallic connectors like the FC and ST made color coding difficult, so colored boots were often used. The TIA 568 color code for connector bodies and/or boots is Beige for multimode fiber except aqua for laseroptimized fiber, Blue for single mode fiber, and Green for APC (angled) connectors. 3.3 Standard Optical Connectors Part Number Code. LP-F11TMMBCHY 11 LP-F LanPro Optical 11 Fiber Solutions Code 11: Fiber Optic Connector T M B Connector Type A C D I F H J 5 L P Q ST Pre Angled FC/PC Pre Angled Typical type FC/PC Pre Angled One Piece Type FC/APC Pre-Angled 8º SC Pre Angled SC Pre Angled Duplex Type SC/APC Pre angled 8º One Piece Type SC II/APC Pre Angled 8º One Piece Type LC Simplex LC Duplex Type LC/APC Simplex Pre Angled 8º M MTRJ Female N MTRJ + Guide Pin Male R MTRJ II S MTRJ II + Guide Pin 1 LC II Simplex 2 LC II Duplex 3 LC II Simplex Square-Flange MODE/Polish Type 1 MM PC Polish 2 SM PC Polish 3 SM SPC Polish 4 SM UPC Polish 5 SM APC Polish Cable Boot Type 1 For 3.0mm cable 2 For 0.9mm cable 3 For 2.0mm cable (Only for MTRJ & LC) 4 For 1.8 mmcable Minizip 5 For both 3.0mm and 0.9mm kit 6 For both 3mm and 2mm kit 4 LC II Duplex Square-Flange 6 SC II Simplex 7 SC II Duplex 8 SC II Simplex Square-Flange 9 SF II Duplex Frange C H Y Boot Color 1 Black 2 Red 3 Yellow 4 Green 5 Blue 6 Ivory 7 Black and Red 8 White Housing 1 Black 2 Red 3 Yellow 4 Green 5 Blue 6 Ivory 7 Black and Red 8 White 9 Metal Yoke 1 Black 2 Red 3 Yellow 4 Green 5 Blue 6 Ivory 7 Black and Red 8 White Blank= None or 0 if there is no Yoke and a clip for duplex

3.4 Standard Connector Types. 3.4.1 ST Connectors. Example P/N s for ST Type Optical Connectors. P/N LanPro LP-F11A1519 LP-F11A2539 3.4.2 FC Connectors. Description The ST connector has been a work horse for years and can be found in every communications room around the globe. Simple to use, precision made, mechanically stable, the bayonet style locking mechanism secures against accidental disconnections. Built with a nickel plated brass body and a ceramic ferrule with a springcrimp barrel assembly and a crimp over sleeve with rubber boot. Cable sizes accommodated: 0.9, 2 and 3 mm. Fiber Optic Connector ST Thread Type MM 62.5/125 PC Polish with both 3mm and 0.9 mm Black Boots. Fiber Optic Connector ST Thread Type SM 9/125 PC Polish with both 3mm and 0.9 mm Yellow Boots. The FC connector is highly used in the telecommunications industry, in which long fiber links of 50 Km or more are common. In these cases the connector needs to have extremely low losses and accurate geometry. The FC connector has a screw thread fitting into the adapter to provide a secure connection. The FC connector is precision made and manufactured to demanding specifications with a nickel plated brass body and a ceramic ferrule/spring/ crimp barrel assembly plus a crimp over sleeve and rubber boot. These connectors are designed for 0.9, 2 and 3mm cable. They provide a consistent long-term mechanical and optical performance. The FC connector is available in single-mode UPC and APC versions as well as multimode. -The connector can be supplied as a pre-assembled one-piece connector or as multi-pieces connector. -Clips are available for SC and LC duplex connectors. Housing kits without ferrule are available. -PC and APC polish are available. Fiber Solutions Short Form Catalog FEATURES Low insertion loss and back reflection loss. High precision alignment. Boots in a variety of colors. Bayonet style housing for easy termination. Ferrule end surface predomed. Nickel plated brass body. Free-floating ceramic ferrule. Example P/N s for FC/PC Type Optical Connectors. LP-F11C1519 LP-F11C2539 Fiber Optic Connector FC Thread Type Multimode 62.5/125 PC Polish, with both 3mm and 0.9 mm Black Boots. Fiber Optic Connector FC Thread Type Singlemode 9/125 PC Polish, with both 3mm and 0.9 mm Yellow Boots. 12

Fiber Solutions Short Form Catalog 3.4.3 SC Connectors are frequently used for newer Network applications. The SC is a snap-in connector that is widely used in singlemode systems for its performance. The SC connector is also available in a Duplex configuration. They offer low cost, simplicity, and durability. SC connectors provide for accurate alignment via their ceramic ferrules. The square, snap-in connector latches with a simple push-pull motion and is keyed. They feature a 2.5mm Ferrule and molded housing for protection. Typical matched SC connectors are rated for 1000 mating cycles and have an Insertion Loss of 0.25 db. LP-F11F15168 LP-F11F25568 SC Connectors. Example P/N s for SC Type Optical Connectors. Simplex SC stands for Subscriber Connector- a general purpose push/pull style Connector developed by NTT. SC has an advantage in keyed duplexibility to support send/receive channels. Fiber Optic Connector SC Simplex Type Multimode 62.5/125 PC Polish Ivory Housing with both 3mm and 0.9 mm Black Boots, and White Yoke. Fiber Optic Connector SC Simplex Type Singlemode 9/125 PC Polish Ivory Housing with both 3mm and 0.9 mm Blue Boots and White Yoke. Duplex LP-F11H15758 LP-F11H25558 3.4.4 LC Connectors. Fiber Optic Connector SC Duplex Type Multimode 62.5/125 PC Polish Blue Housing with 2x3.0mm and 2x0.9mm Black and 2x3.0mm and 2x0.9 red Boots. Fiber Optic Connector SC Duplex Type Singlemode 9/125 PC Polish Blue Housing with both 3mm and 0.9 mm Blue Boots. This is an optical connector that reduces by half the size of a SC connector, this makes the scale of integration very high, it is increasingly common to see the switch with fiber ports for integrated duplex LC connectors mini GBIC or SFP modules. The anchoring system is very similar to the RJ must press on the tab above to introduce or release, this tab is so small that this is done with a fine-tipped screwdriver. The LC optical connector is considered a fourth-generation, improved size, strength and ease of use compared to previous generations. Example P/N s for LC Type Optical Connectors. Simplex LP-F11L1586 LP-F11L2585 Duplex LP-F11P1586 LP-F11P2585 Fiber Optic Connector LC Simplex Type MM 62.5/125 PC Polish Ivory Housing with both 3mm and 0.9 mm White Boots. Fiber Optic Connector LC Simplex Type SM 9/125 PC Polish Blue Housing with both 3mm and 0.9 mm White Boots. Fiber Optic Connector LC Duplex Type Multimode 62.5/125 PC Polish Ivory Housing with both 3mm and 0.9 mm White Boots Ivory Clip. Fiber Optic Connector LC Duplex Type Singlemode 9/125 PC Polish Blue Housing with both 3mm and 0.9 mm White Boots Blue Clip. 13

LC/APC Simplex LP-F11Q5184 LP-F11Q5284 LP-F11Q5384 3.4.5 MTRJ. Fiber Optic Connector LC/APC Simplex, Singlemode 62.5/125 APC Polish, Green Housing 3.0 mm White Boot 15mm. Fiber Optic Connector LC/APC Simplex, Singlemode 62.5/125 APC Polish, Green Housing 0.9 mm White Boot 8mm. Fiber Optic Connector LC/APC Simplex, Singlemode APC Polish, Green Housing 2.0 mm White Boot 15mm. Example P/N s for MTRJ Type Optical Connectors MTRJ Female. LP-F11M1311 LP-F11M2311 The MT-RJ connector was developed to meet growing customer demands for smaller, lower cost, and easier-to-use fibre optic connectivity. The MT-RJ reduces the space required on panels, wall plates and in closets by 50% throughout the network. This small form factor connector is ideal for horizontal and fibre-to-the-desk applications. The MT-RJ uses an improved version of an industry standard RJ-45 type plug. Fiber Optic Connector Female MTRJ Type MM 62.5/125 PC Polish Black Housing with Black Boot. Fiber Optic Connector Female MTRJ Type SM 9/125 PC Polish Black Housing with black boot. Fiber Solutions Short Form Catalog MTRJ Male LP-F11N1311 LP-F11N2311 Fiber Optic Connector Male MTRJ (With Guide Pin) Type Multimode 62.5/125 PC Polish Black Housing with Black Boot. Fiber Optic Connector Male MTRJ (With Guide Pin) Type Singlemode 9/125 PC Polish Black Housing with Black Boot. 3.4.6 Field Connectors. Field Installable connectors provide quick and easy installation and superior performance. It just takes 2 minutes to finish the installation. It is also a strong and reliable termination, The high precision mechanical splice technology enables fiber optical network to be installed effectively. Multimode and singlemode SC and ST are available. Performance. Fiber Type Polish Connection Loss Return Loss Singlemode SPC 0.9dB(Ave. 0.4dB) 40dB Multimode PC 0.75dB(Ave. 0.3dB) - FEATURES Factory-Polish & non-epoxy connector can save time of field connector. Compliant with TIA/EIA-568-B3 & FOCIS standard. 100% factory test for insertion loss. Easy to clean, straightforward termination procedure. 14

Fiber Solutions Short Form Catalog Example P/N s for SC&ST Field Type Optical Connectors. LP-F30A1519 LP-F30A2539 LP-F30F15166 LP-F30F25555 3.4.7 Fiber Optic Field Connector ST Thread Type MM 62.5/125 PC Polish with both 3.0mm and 0.9mm Black Boots. Fiber Optic Field Connector ST Thread Type SM 9/125 PC Polish with both 3.0mm and 0.9mm Yellow Boots. Fiber Optic Field Connector SC Type MM 62.5/125 PC Polish Ivory Housing with both 3.0mm and 0.9mm Black Boots Ivory Yoke. Fiber Optic Field Connector SC Type SM 9/125 PC Polish Blue Housing with both 3.0mm and 0.9mm Blue Boots Blue Yoke. Cutter Tool for Field Connector. 4 Cable End Connector Types/Arrangements. LPT-F30TOOL This tool is specifically designed for cutting the fiber to the size required by this connector. FIBER OPTIC PATCH CORD AND PIGTAILS. ST LC LC Duplex SC SC Duplex E-2000 4.1 MU Connector End-Face Preparation Polish Grades. PC Polish The Physical Contact (PC) polish results in a slightly curved connector surface, forcing the fiber ends of mating connector pairs into physical contact with each other. This eliminates the fiber-to-air interface, there by resulting in back reflections of -30 to -40 db. The PC polish is the most popular connector end-face preparation, used in most applications. SPC Polish In the Super PC (SPC) polish, an extended polishing cycle enhances the surface quality of the connector, resulting in back reflections of -40 to -55 db. This polish is used in high-speed, digital fiber optic transmission systems. UPC Polish, Ultra Physical Contact UPC has Back reflections of -50dB or higher APC Polish The Angled PC (APC) polish, adds an 8 degree angle to the connector end-face. Back reflections of <-60 db can routinely be accomplished with this polish. FC MTRJ 15 Flat PC and SPC APC Fiber Jacket Diameters available: 0.9mm, 2.0mm, 3.0mm.

4.2 Specifications. Specifications ST, MTRJ ST, MTRJ Specifications SC,FC SC, FC SPEC\Mode Single Mode(SM) Multi-Mode(MM) ST MTRJ ST MTRJ Insertion Loss (db) 0.3 0.5 0.3 0.5 Return Loss(dB) 45 35 35 20 Repeatability Durability (Mating Cycles) Op. Temp. range Polish Insertion Loss db Return Loss (db) Durability (Mating Cycles) Op. Temp. range SM PC 0.1dB >1000-40ºC to +80ºC MM UPC APC 0.3 0.3 0.2 0.3 40 35 50 60 >1000 SC:-25ºC ~ +70ºC FC: 40ºC ~ +80ºC >100 N Fiber Solutions Short Form Catalog Specifications LC,MU LC, MU Polish SM MM Insertion Loss(dB) 0.3 0.3 0.4 Return Loss(dB) 45 35 50 Repeatability 0.1dB Durability (Mating >1000 Cycles) Op. Temp. range -25ºC ~ +70ºC PC UPC Technical Index 9/125 A1 A2 B1 B2 Insertion 0.14 0.18 0.17 0.11 Losss(dB) Return Loss(dB) 52 50 54 51 16

Fiber Solutions Short Form Catalog 4.3 LP-F XX TT PP CC Patchcord and Pigtail part numbering code. LP-FXXTTPPCCJLLL J LL LanPro Optical Fiber Solutions Code 12: Fiber Optic Simplex Patchcord/pig Tail 13: Fiber Optic Duplex Patchcord Connector Type for both ends 0 None A ST Simplex C FC/PC Typical type Simplex disassembled D FC/PC Simplex E E2000 Simplex G E2000 Duplex 5 E2000/SM/APC Simplex 6 E2000/SM/APC Duplex I FC/SM/APC Simplex F SC SIMPLEX H SC Duplex Type K SC/SM/APC Duplex J SC/SM/APC Simplex L LC SIMPLEX P LC Duplex 7 LC/APC Simplex 8 LC/APC Duplex M MTRJ Female N MTRJ with Guide Pin Male Polish Grade M1 (A)Multimode PC polish S1 (B)Singlemode SPC polish, RL>40dB S2 (C)Singlemode, UPC polish, RL>50dB S3 (D)Singlemode, APC polish, RL>60dB Cable Type 01 Multimode 62.5/125um, 3.0 mm simplex cable, PVC Orange Jacket 03 Multimode 62.5/125um, 0.9 mm simplex cable, PVC Orange Jacket 04 Singlemode 9/125um, 3.0mm simplex cable, PVC Yellow Jacket 06 Singlemode 9/125um, 0.9mm simplex cable, white 07 Multimode 62.5/125um, 3.0mm zipcord cable, PVC Orange Jacket 08 Singlemode 9/125um, 3.0mm zipcord cable, PVC Yellow Jacket 09 Multimode 50/125um, 3.0mm simplex cable 10 Multimode 50/125um, 0.9mm simplex cable, PVC Orange Jacket 11 Multimode 50/125um, 3mm zipcord cable, gray 12 Multimode 62.5/125um, 2.0mm simplex cable, PVC Orange Jacket 13 Multimode 50/125um, 2.0mm simplex cable, PVC Orange Jacket 14 Singlemode 9/125um, 2.0mm simplex cable, PVC Yellow Jacket 16 Multimode 62.5/125um, 3.0mm MT-RJ dualan cable, PVC Orange Jacket 18 Multimode 50/125um, 3.0mm MT-RJ dualan cable, gray 23 Multimode 62.5/125um, 2.0mm zipcord cable, PVC Orange Jacket 24 Singlemode 9/125um, 2.0mm zipcord cable, PVC Yellow Jacket 25 Multimode 50/125um, 2.0mm zipcord cable, gray 26 Multimode 62.5/125um 1.8mm Zipcord PVC Orange Jacket 27 Singlemode 9/125um, 1.8mm, Mini-Zipcord, PVC Yellow Jacket 28 Multimode 50/125um, 1.8mm Mini-Zipcord, Gray 34 Multimode 50/125um, 0.9mm Simplex, Gra 35 Multimode 50/125um, 3mm Zipcord, Orange Jacket Cable Jacket Type P PVC Jacket L LSOH (LSZH) Jacket Length(e.g:) 10M (meter) 10F (Feet) XX TT PP CC J LLL Note: These two leters indicate both ends of the patchcord. E.g: AA Means: ST to ST A0 Means: ST pigtail Example P/N s for Fiber Optic Duplex Patchcords. LP-F13AAM107P3M LP-F13ADM107P3M LP-F13ADS108P3M FIBER OPTIC DUPLEX PATCHCORD 3m, ST/ST, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, FC/ST, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, FC/ST, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. 17

LP-F13AHM107P3M LP-F13AMM123P3M LP-F13APM107P3M LP-F13APS108P3M LP-F13DDM107P3M LP-F13DDS108P3M LP-F13DHM107P3M LP-F13DHS108P3M LP-F13HHM107P20M LP-F13HHM107P3M LP-F13FFM107P3M LP-F13HHS108P3M LP-F13FFS108P3M LP-F13HPM107P3M LP-F13FLM107P3M LP-F13HPS108P3M FIBER OPTIC DUPLEX PATCHCORD 3m, ST/SC duplex, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC PATCHCORD 3m, ST/MTRJ, PC POLISH 62.5/125 MM, Zipcord 2mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, LC duplex/st, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, LC duplex/st, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, FC/FC, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, FC/FC, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, FC/SC duplex, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, FC/SC duplex, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. FIBER OPTIC DUPLEX PATCHCORD 20m, SC Duplex/SC Duplex, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, SC duplex/sc duplex, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, SC simplex/sc simplex, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, SC duplex/sc duplex, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, SC simplex/sc simplex, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, SC duplex/lc duplex, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, SC simplex/lc simplex, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, SC duplex/lc duplex, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. Fiber Solutions Short Form Catalog LP-F13FLS108P3M FIBER OPTIC DUPLEX PATCHCORD 3m, SC simplex/lc simplex, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. LP-F13HMM123P3M FIBER OPTIC DUPLEX PATCHCORD 3m, SC duplex/mtrj, PC POLISH 62.5/125 MM, Zipcord 2mm PVC Orange Jacket. LP-F13HMS127P3M FIBER OPTIC DUPLEX PATCHCORD 3m, SC duplex/mtrj, SPC POLISH 9/125 SM, DUPLEX Mini Zipcord 1.8mm PVC Yellow Jacket. LP-F13IIS308P3M FIBER OPTIC DUPLEX PATCHCORD 3m, FC APC Simplex/ FC APC Simplex, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. LP-F13JJS308P3M LP-F13MMS124P3M LP-F13MPM123P3M LP-F13MPS124P3M LP-F13PPM107P3M LP-F13LLM107P3M LP-F13PPS108P3M LP-F13LLS108P3M LP-F13FPM107P3M FIBER OPTIC DUPLEX PATCHCORD 3m, SC Simplex/SC Simplex, APC, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, MTRJ/MTRJ, SPC POLISH 9/125 SM, DUPLEX 2mm PVC Yellow Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, LC duplex/mtrj, PC POLISH 62.5/125 MM, Zipcord 2mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, LC duplex/mtrj, SPC POLISH 9/125 SM, Zipcord 2mm PVC Yellow Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, LC duplex/lc duplex, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, LC simplex/lc simplex, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, LC duplex/lc duplex, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, LC simplex/lc simplex, SPC POLISH 9/125 SM, Zipcord 3mm PVC Yellow Jacket. FIBER OPTIC DUPLEX PATCHCORD 3m, SC simplex/lc duplex, PC POLISH 62.5/125 MM, Zipcord 3mm PVC Orange Jacket. 18

Fiber Solutions Short Form Catalog 5 SC Adaptor Simplex Type FIBER OPTIC ADAPTORS. Are mechanical devices designed to align fiber-optic connectors. It contains the split sleeve (interconnect sleeve) that holds the two ferrules of both connectors, at the front and back of the panel, together. ST Adaptor Thread Type ST Adaptor Flange Type SC Adaptor Duplex Type ST Adaptor Duplex Type MT-RJ Adaptor FC/PC Adaptor SquareType LC Adaptor Duplex Type FC/PC Adaptor D Type SC/APC Adaptor Simplex Type FC/PC Adaptor Flange Type ST to FC/PC Hybrid Adaptors ST to SC Hybrid Adaptors FC/PC to SC Adaptor ST to SC Duplex Adaptor 5.1 Fiber Optic Adaptor Code. LP-F15TTSSC 19 LP-F LanPro Fiber Optical 15 15: Fiber Optic Adaptor TT SS C Connector Type 01 ST Thread Type 02 ST Flange Type 03 ST Plastic Duplex Type 04 FC/PC Metal Square Type 05 FC/PC Metal D Type 06 FC/PC Flange Type 07 SC Simplex Type 08 SC Duplex Type 09 ST to FC/PC Hybrid Type 10 ST to SC Hybrid Type 11 FC/PC to SC Hybrid Type 12 ST to SC Duplex Hybrid Type 13 MT-RJ Type 14 LC Duplex Type 15 LC Duplex Type Flange Sleeve Type M1 Multi Mode Phosphor Bronze Sleeve S1 Singlemode Zirconia Sleeve Housing Color 1 Blue 2 Green 3 Ivory 4 Nickel plated bronze 5 White 15 TT SS C

Example P/N s for Optical Adaptors. LP-F1501M14 ST Thread MM Phorphor Bronze Sleeve Adaptor. LP-F1501S14 ST Thread SM Zirconia Sleeve Adaptor. LP-F1502M11 ST MM Phosphor Bronze Sleeve Flange Type Adaptor. LP-F1502S11 ST SM Zirconia Sleeve Flange Type Adaptor. LP-F1503M11 ST MM Phosphor Bronze Sleeve Duplex Type Adaptor. LP-F1503S11 ST SM Zirconia Sleeve Duplex Type Adaptor. LP-F1504M14 FC/PC MM Phosphor Bronze Sleeve Adaptor. LP-F1504S14 FC/PC SM Zirconia Sleeve Adaptor. LP-F1505M14 FC/PC MM Phosphor Bronze Sleeve Adaptor. LP-F1505S14 FC/PC SM Zirconia Sleeve Adaptor. LP-F1506M11 FC/PC MM Phosphor Bronze Sleeve Adapter. LP-F1506M11 FC/PC SM Zirconia Sleeve Adaptor. LP-F1507M11 SC MM Phosphor Bronze Sleeve Adapter. LP-F1507S11 SC SM Zirconia Sleeve Adaptor. LP-F1508M11 SC Duplex MM Phosphor Bronze Sleeve Adaptor. LP-F1508S11 SC Duplex SM Zirconia Sleeve Adaptor. LP-F1513M15 MT-RJ MM Adaptor. LP-F1514M11 LC Duplex MM Phosphor Bronze Sleeve Adaptor. LP-F1514S11 LC Duplex SM Zirconia Sleeve Adaptor. LP-F1507S12 SC/APC Zirconia Sleeve Adaptor. LP-F1509M11 ST to FC/PC MM Phosphor Bronze Sleeve Adaptor. LP-F1509S11 ST to FC/PC SM Zirconia Sleeve Adaptor. LP-F1510M11 ST to SC MM Phosphor Bronze Sleeve Adaptor. LP-F1510S11 ST to SC SM Zirconia Sleeve Adaptor. LP-F1511M11 FC/PC to SC MM Phosphor Bronze Sleeve Adaptor. LP-F1511S11 FC/PC to SC SM Zirconia Sleeve Adaptor. LP-F1512M11 ST to SC Duplex Phosphor Bronze Sleeve Adaptor. LP-F1512S11 ST to SC Duplex Zirconia Sleeve Adaptor. Fiber Solutions Short Form Catalog 6 FIBER OPTIC WALL ENCLOSURES (BOXES) AND FO PATCH PANELS. LanPro manufactures a variety of sturdy, well designed Wall Enclosures and Fiber Optic Patch Panels for Rack mounting that serve most fiber distribution needs in the Home and Medium size optical structured cabling. With loaded or unloaded versions, flexibility is a very desired characteristic our customers anticipate from Us. Based in a modular design that carries different types of modules with adaptors and fiber optic splices containers, they represent a very practical LanPro solution for your needs. Dimension: 14.5 x13.8 x4.4 Panel Size: Apply with 99 x 37mm Panel 20

Fiber Solutions Short Form Catalog 6.1 XX T P CC AA ZZ Fiber Optic Wall Enclosures(Boxes) and FO Patch Panels CODES. LP-FXXTPCCAAZZ Fiber Optic Wall Enclosure(Box) or Patch Panel Loaded or Unloaded 18 Fiber Optic Wall Enclosure(Box) or Patch Panel Unloaded 19 Fiber Optic Wall Enclosure(Box) or Patch Panel Loaded Box/Panel Type 1 Fiber Optic Wall Mounting Enclosure (Box) 4 Patch Panel Rack mounted Ports A B C D E F Box/Panel Color IV Ivory BK Black 12 Port 24 Port 36 Port 48 Port 12 and 24 Port 36 and 48 Port Adaptor Type 01 ST Thread Type 02 ST Flange Type 03 ST Duplex Type 04 FC/PC Metal Square Type 05 FC/PC Metal D Type 06 FC/PC Flange Type 07 SC Simplex Type 08 SC Duplex Type 09 ST to FC Hybrid Type 10 ST to SC Hybrid Type 11 FC to SC Hybrid Type 12 ST to SC Duplex Type 13 MTRJ Type 14 LC Duplex Square Type 15 LC Simplex Type 16 LC Duplex Footprint Type 18 SC Flangeless Type 19 SC Duplex Flangeless Type XX Mixed Adaptor Type YY Without adaptors/panels Sleeve Type M1 Multimode Phosphor Bonze Sleeve S1 Singlemode Zirconia Sleeve Blank Don t care XX T P CC AA ZZ 6.2 Fiber Optic Wall Enclosures (Boxes) Empty. These wall enclosures come without Modules for you to fill configure with a variety of Fiber Optic Adaptor Modules. 12 and 24 Port Unit 364mm * 350mm * 81mm (14.5*13.8*3.2 inches) 36 and 48 Port Unit 364mm * 350mm * 112mm (14.5*13.8*4.4 inches) 21

HOW TO LOAD THE WALL ENCLOSURE? For 12 port you need... 2 x 17-XXBXX (130x29mm)adaptor panels + 2 x 16-XXB-BK. For 24 port you need... 4 x 17-XXBXX (130x29mm) adaptor panels. For 36 port you need... 6 x 17-XXCXX plate + 2 x 16-XXB-BK (99x37mm). For 48 port you need... 8 x 17-XXCXX plate (88x37mm). Example P/N s for Optical Empty Wall Enclosure. LP-F181EBKYY LP-F181FBKYY 6.3 12 & 24 port empty Fiber Optic Wall Enclosure Without panels. 36 & 48 port empty Wall Enclosure Without panels. Fiber Optic Rack Mounted Patch Panels Unloaded. Example P/N s for Empty Rack Mount Unloaded Patch Panels. LP-F184ABKYY LP-F184CBKYY LP-F184DBKYY 12 Port empty Rack Mount Unloaded Patch Panel Black Color. 36 Port empty Rack Mount Unloaded Patch Panel Black Color. 48 Port empty Rack Mount Unloaded Patch Panel Black Color. Fiber Solutions Short Form Catalog 6.4 24 Port Fiber Optic Rack Mounted Patch Panels Factory Loaded. These are 24 port rack mount cabinets. They are not configurable in, they have to be ordered from factory, fully loaded. No options on this model. The factory can configure the product to customer connector specs and special combinations can be ordered. all these holes are pre-punched and fixed SC Duplex SC Simplex FC ST LC Duplex Square Type LC Simplex LC Duplex (SC foot print) & MTRJ Compatible 22

Fiber Solutions Short Form Catalog Example P/N s for 24 Port Fiber Optic Rack Mounted Patch Panels Factory Loaded. LP-F194BBK08M1 LP-F194BBK08S1 LP-F194BBK16M1 LP-F194BBK16S1 7 FIBER OPTIC ADAPTOR PANEL MODULES. Fiber Optic Wall Enclosures (Boxes) and Fiber Optic Rack Mounted Patch Panels use Fiber Optic Adaptor Panel Modules that can be loaded or unloaded with fiber optic adaptors. A choice of Fiber Optic Adaptor Panels Modules are manufactured by LanPro with stringent specifications in order to comply with the demanding standards of today. 7.1 Fiber Optic Adaptor Panel Unloaded CODE. LP-F16HHPCC 16: Adaptor Unloaded Type & Port, xx: don t care Adaptor Type Adaptor Type: 24 Port MM Loaded with SC Duplex Type Adaptors Phosphor Bronze Sleeves. 24 Port SM Loaded with SC Duplex Type Adaptors Zirconia Sleeves. 24 Port MM Loaded with LC Duplex Footprint Type Adaptors Phosphor Bronze Sleeves. 24 Port SM Loaded with LC Duplex Foot Print Type Adaptors Zirconia Sleeves. Hole Type HH P: Panel Type A 4Ports P: Panel Type B 6Ports HH P: Panel Type C 2x3Ports P: Panel Type D 8Ports 130x29mm 130x29mm 99x37mm 160x25.5mm ST Thread 01 01 01A 01B 01C 01D ST Flange 02 02 02A 02B 02C 02D ST Duplex 03 03 NA NA 03C NA FC Square 04 04 04A 04B 04C 04D FC D Type 05 04 04A 04B 04C 04D FC Flange 06 02 02A 02B 02C 02D SC Simplex 07 02 02A 02B 02C 02D SC Duplex 08 03 03A 03B 03C 03D LC Duplex 14 05 x 05B 05C 05D Square Type LC Simplex 15 06 06A 06B 06C 06D LC Duplex (SC Footprint) 16 07 x 07B 07C 07D MTRJ 13 07 x 07B 07C 07D ST to FC 09 02 02A 02B 02C 02D ST to SC Simplex 10 02 02A 02B 02C 02D FC to SC 11 02 02A 02B 02C 02D ST to SC Duplex 12 03 03A 03A 03C 03D Dummy N.A. xx xxa xxb xxc xxd P Dummy Panel & Size A=B: Dummy Panel, 130x29mm C: Dummy Panel, 99x37mm D: Dummy Panel, 160x25.5mm HH Hole Types Note: Adaptor Type is included in the table for reference purpose only as it is not part of the formula. It indicates that this adaptor type uses the corresponding hole type in the column at the right. 23

ST Thread 01 02.311 9.8.385 FC Flange, ST Flange, SC Simplex.520.526.375 RECOMMENDED PANEL HOLE 2X R.053 Fiber Solutions Short Form Catalog ST,SC Duplex, ST to SC Duplex 03 04 #2-56UNC-2B 2x FC Square, FC D Type 45.188.530 26.1 30.7.375 (.375) 9.6 SUGGESTED PANEL CUTOUT MAXIMUN PANEL THICKNESS 1.7 2X.098 05 06 LC Duplex Square Type LC Simplex Simplex Mounting Duplex Mounting Panel Thickness 2.3 - Panel Cutout Dimensions for Mounting LC Adapters Dimension Minimun (mm) Maximun (mm) A C A 11.7 11.8 B 7.1 7.2 C 13.2 13.4 B D 06 05 E* D 13.2 13.4 E* 1.2 1.7 *Panel Thickness E applies after srface preparation i.e. painting, etc. 24

Fiber Solutions Short Form Catalog 25 07 7.2 LC Duplex SC Footprint/MTRJ Fiber Optic Adaptor Panel Loaded CODE. LP-F17TTPCCSSC 17: Adaptor Loaded Type & Port Adaptor Type Panel Color CC IV= Ivory BK= Black Adaptor Type: TT Hole Type P: Panel Type A 4Ports P: Panel Type B 6Ports Sleeve Type SS M1 Multimode Phosphor Bronze Sleeve S1 Singlemode Zirconia Sleeve P: Panel Type C 2x3Ports P: Panel Type D 8Ports 130x29mm 130x29mm 99x37mm 160x25.5mm ST Thread 01 01 01A 01B 01C 01D ST Flange 02 02 02A 02B 02C 02D ST Duplex 03 03 03A 03B 03C 03D FC Square 04 04 04A 04B 04C 04D FC D Type 05 04 05A 05B 05C 05D FC Flange 06 02 06A 06B 06C 06D SC Simplex 07 02 07A 07B 07C 07D SC Duplex 08 03 08A 08B 08C 08D ST to FC 09 02 09A 09B 09C 09D ST to SC Simplex 10 02 10A 10B 10C 10D FC to SC 11 02 11A 11B 11C 11D ST to SC Duplex 12 03 12A 12B 12C 12D MTRJ 13 07 x 13B 13C 13D LC Duplex Square Type 14 05 x 14B 14C 14D LC Simplex 15 06 15A 15B 15C 15D LC Duplex Footprint type 16 07 x 16B 16C 16D SC Flangeless 18 02 18A 18B 18C 18D SC Duplex Flangeless CC.71 18.39 9.9 STANDARD MT-RJ MOUNTING PATTERN Panel Color CC IV= Ivory BK= Black 19 03 19A 19B 19C 16D.093 2.36.42 10.7.71 18.39 9.9 STANDARD SC CUTOUT CC SS C Note: Hole Type is included in the table for reference purpose only as it is not part of the formula. It indicates that this hole type corresponds to the Adaptor Type TT in the column at the left. P.093 2.36.525 13.3 Adaptor Color C 1=Blue Used for SM 2=Green Used for SM APC Polish 3=IVORY used for MM 4=Black Used for MM X=Metal Used for MM and SM

Few Example P/N s for Adaptor modules for Empty Rack Mount Loaded Patch Panels. LP-F1701BBKM1X LP-F1705BBKM1X LP-F1705BBKS1X LP-F1708BBKM13 LP-F1708BBKS11 LP-F1716BBKM13 LP-F1716BBKS11 LP-F16XXBBK LP-F1701DBKM1X LP-F1705DBKM1X LP-F1705DBKS1X LP-F1708DBKM13 LP-F1708DBKS11 These panels are used on 12 & 24 wall Enclosure and 12 rack mount cabinets only Fiber Optic Adaptor Black Panel Loaded with 6 ST Thread Adaptors Multimode with Phosphor Bronze Sleeve, 130x29 mm size for 12&24 wall Enclosures. Fiber Optic Adaptor Black Panel Loaded with 6 FC D Type Adaptors Multimode with Phosphor Bronze Sleeve 130x29mm, for 12 & 24 wall Enclosures. Fiber Optic Adaptor Black Panel Loaded with 6 FC D Type Adaptors Singlemode with Zirconia Sleeve 130x29mm, for 12 & 24 wall Enclosures. Fiber Optic Adaptor Black Panel Loaded with 3 Ivory SC Duplex Adaptors Multimode with Phosphor Bronze, Sleeve 130x29mm, for 12 & 24 wall Enclosures. Fiber Optic Adaptor Black Panel Loaded with 3 Blue SC Duplex Adaptors Singlemode with Zirconia Sleeve, 130x29mm, for 12 & 24 wall Enclosures. Fiber Optic Adaptor Black Panel Loaded with 3 Ivory LC Duplex Footprint Type Adaptors (6 Ports) Multimode with Phosphor Bronze, Sleeve 130x29mm, for 12 & 24 wall Enclosures. Fiber Optic Adaptor Black Panel Loaded with 3 Blue LC Duplex Footprint Type Adaptors (6 Ports) Singlemode with Zirconia Sleeve, 130x29mm, for 12 & 24 wall Enclosures. Blank(Dummy) Panel 130x29mm for 12 & 24 Port. Used on 48 port rack mount cabinets only. Fiber Optic Adaptor Black Panel Loaded with 8 ST Thread Adaptors Multimode with Phosphor Bronze Sleeve, 160X25.5 mm, for 48 Ports Rack Mount. Fiber Optic Adaptor Black Panel Loaded with 8 FC D Type Adaptors Multimode with Phosphor Bronze Sleeve 160X25.5 mm, for 48 Port Rack Mount. Fiber Optic Adaptor Black Panel Loaded with 8 FC D Type Adaptors Singlemode with Zirconia Sleeve 160X25.5 mm, for 48 Port Rack Mount. Fiber Optic Adaptor Black Panel Loaded with 4 Ivory SC Duplex Adaptors Multimode with Phosphor Bronze Sleeve, 160X25.5 mm, for 48 Port Rack Mount. Fiber Optic Adaptor Black Panel Loaded with 4 Blue SC Duplex Adaptors Singlemode with Zirconia Sleeve, 160X25.5 mm, for 48 Port Rack Mount. LP-F1716DBKM13 Fiber Optic Adaptor Black Panel Loaded with 4 Ivory LC Duplex Footprint Type Adaptors (8 Ports) Multimode with Phosphor Bronze Sleeve, 160X25.5 mm, for 48 Port Rack Mount. LP-F1716DBKS11 Fiber Optic Adaptor Black Panel Loaded with 4 Blue LC Duplex Footprint Type Adaptors (8 Ports) Singlemode with Zirconia Sleeve, 160X25.5 mm, for 48 Port Rack Mount. LP-F16XXDBK Blank(Dummy) Panel 160x25.5mm for 48 Port Rack Panel. Fiber Solutions Short Form Catalog LP-F1701CBKM1X LP-F1705CBKM1X LP-F1705CBKS1X LP-F1708CBKM13 LP-F1708CBKS11 LP-F1716CBKM13 LP-F1716CBKS11 LP-F16XXCBK Used on 36 Ports wall Enclosure and rack mount units. Fiber Optic Adaptor Black Panel Loaded with 6 ST Thread Adaptors Multimode with Phosphor Bronze Sleeve, 99X37 mm, for 36 Ports Only. Fiber Optic Adaptor Black Panel Loaded with 6 FC D Type Adaptors Multimode with Phosphor Bronze Sleeve 99X37 mm, for 36 Ports Only. Fiber Optic Adaptor Black Panel Loaded with 6 FC D Type Adaptors Singlemode with Zirconia Sleeve 99X37 mm, for 36 Ports Only. Fiber Optic Adaptor Black Panel Loaded with 3 Ivory SC Duplex Type Adaptors (6 Port) Multimode with Phosphor Bronze Sleeve, 99X37 mm, for 36 Ports Only. Fiber Optic Adaptor Black Panel Loaded with 3 Blue SC Duplex Type Adaptors (6 Port) Singlemode with Zirconia Sleeve, 99X37 mm, for 36 Ports Only. Fiber Optic Adaptor Black Panel Loaded with 3 Ivory LC Duplex Footprint Type Adaptors (6 Ports) Multimode with Phosphor Bronze Sleeve, 99X37 mm, for 36 Ports Only. Fiber Optic Adaptor Black Panel Loaded with 3 Blue LC Duplex Footprint Type Adaptors (6 Ports) Singlemode with Zirconia Sleeve, 99X37 mm, for 36 Ports Only. Blank(Dummy) Panel 99x37mm for 36 Port Wall Enclosure. 26

Fiber Solutions Short Form Catalog 8.1 8 Tools for Fiber Optics. LPT-FKIT01. LPT-FCS01 Tool, Carbide Scribe ( Cleaving Tool). LanPro has gathered the best tools for the common SC, ST and FC connectors termination in a useful kit for the field technician. This kit is composed of the following list of components: This precision tool scratches the fiber lightly generating a starting point for the fracture that propagates radially across the surface of the fiber when bent or pulled by the technician, a clean and a nearly flat cleave is generated in preparation to the polishing phase. LPT-FKCUT01 Tool, Fiber Optic Kevlar Cutter. This specially made stain less steel with chrome plating finish Kevlar cutting tool is ergonomically designed for comfortable use and for easily cutting the protective Kevlar yarns of a fiber optic cable. Length 5.8 (147mm). LPT-FSTRP01 Tool, Fiber Optic Cable Stripper. This precision tool made of hardened carbon steel and black oxide finish has been ergonomically designed for comfortable operation and has three(3) stripping guides for 2mm outer jackets, 250um and 900um buffers, and includes adjustment for special gauges. Size is: 6.3 (162mm). LPT-FSTPOL01 Tool, Fiber Optic Polish Disk for ST Connectors. This puck for hand polishing ST type fiber optic connectors is fabricated with CNC machines for repeatability, and the highest quality and accuracy. The special design doesn t permit vapor locking and the development of surface tension so your ST connectors properly polished. Made of Stainless Steel for durability. 27

LPT-FSCPOL01 Tool, Fiber Optic Polish Disk for SC and FC connectors. This puck for hand polishing SC and FC type fiber optic connectors is fabricated with CNC machines for repeatability, and the highest quality and accuracy. The special design of this tool prevents lock of vapor and development of surface tension so your SC and FC type connectors properly polished. It is made for durability with Stainless-Steel. LPT-FSRG01 Tool, Siringe for Optical Connector Epoxy Injection. These are specially suited Syringes for the job of injecting the epoxy adhesive needed in the connector preparation, work in conjunction with the LPT-FSRGTIP01. LPT-FSRGTIP01 Tool, Siringe Tip for Optical Connector Epoxy Injection. These are specially suited flat tip needles for the job of injecting the epoxy adhesive needed in the connector preparation, work in conjunction with the LPT-FSRG01 syringe. Fiber Solutions Short Form Catalog LPT-FRPAD01 Tool, Rubber Working Pad. This pad is a perfect working area for preparing the optical connectors for firm positioning your work. LPT-FCRMP01 Tool, Crimper.137,.190 and.173 H dies. This crimp tool includes a handle and 3 hex dies: 0.137, 0.190 and.173 H dies. This crimp tool can be used on all our OEM ST, SC and FC connectors. LPT-FMIX01 Tool, Epoxy Mixer. These mixers are made of PVC and help you mix the adhesive, and are re-usable. LPT-FMIXP01 Tool, Epoxy Mixer Pad. This pad is made of PVC and can is used to mix the adhesive. It can be re-used. 28

Fiber Solutions Short Form Catalog LPT-FWIP01 Tool, Wipe Paper. These wipes come in two fashions, Dry Type and Wet Type, both antistatic. The wet for cleaning the fibers from the gel substance that protects them and the dry to clean any article left after the wet cleaning. LPT-FCLEAN01 Tool, Cleanser. Alcohol based cleaner for damping the wet papers for cleaning the fibers from the gel substance that protects them. LPT-FGLASS01 Tool, Glass Working Pad. This Glass working pad is a very flat surface for placing the polish film and facilitate a proper polish to the fiber. LPT-FABEPOX01 Tool, Two Part Fast Epoxy Glue. This is a two part fast 5 minutes epoxy adhesive for preparing the fiber optic connector. LPT-FPOFLM01 Tool, 6um (Brown Color) Diamond Polish Film. A square sheet of precise 6 um (Brown color) diamond polish film. LPT-FPOFLM02 Tool, 1um (Purple Color) Diamond Polish Film. A square sheet of precise 1 um (Purple color) diamond polish film. 29

LPT-FPOFLM03 Tool, 0.05um(White Color)Aluminum Oxide Polish Film. A square sheet of precise 0.5 um (White color) Aluminum Oxide diamond polish film. 8.1 LanPro s microscope for Optical Fiber inspection enables the technician to do quality inspection of polished terminations. It helps the field technician s decision on accepting or rejecting the finished connector. 8.2 LPT-FSCOPE01 LPT-CS3B Adjustable Cable Slitter. 6 inches in length (150mm) Patented design easily adjusts to slit the jackets of 4.5mm to 25mm (0.18-1.0 ) diameter cables. With adjustable tension. Fiber Solutions Short Form Catalog Replacement blade: LPT-C3251. 30

LPFSOLSF_CAT_ENB01W