Connessioni tra VideoJet10, VIP10, ZN-T8000 e dispositivi supportati da CBCController, ZNController, DEVController Cabling between VideoJet10,VIP10, ZN-T8000 and devices allowed by CBCController, ZN-Controller, DEVController Vicon P&T V1311VPS 2 Rx+ Response OUT + 3 Tx- Command IN - 5 GND GND 7 Tx+ Command IN + 8 Rx- Response OUT - Surveyor-VFT 2 Rx+ Response OUT + 3 Tx- Command IN - 5 GND GND 7 Tx+ Command IN + 8 Rx- Response OUT - V1311-VPS: Dip Switch SW1: n 5, n 4 ON, n 3, n 2, n 1 Dip Switch SW2: address Surveyor: Dip Switch SW1: n 1 PAL, n 2 VPS, n 3 DUPLEX, n 4 RS422, n 5~8 Dip Switch SW2: address (HTML: Interfaces COM1) Serial port function: Vicon Dome Baud Rate: 4800 CDR-04S CDR-01S CDR-04S CDR-01S 2 Tx RX RX 3 Rx RS 232 TX TX 5 GND GND GND CDR-01S/ CDR-04S: Remote Mode: RS-232 ID: 000 (Default) (HTML: Interfaces COM1/COM2)
DTRX3 DTRX3 3 Tx- RxB 7 Tx+ RxA Web server (HTML: Interfaces COM1) Serial port function: DTRX3 SW328+DTRX3 DTRX3 SW328 3 Tx- RxB Utilizzare il cavo in dotazione alla matrice 7 Tx + RxA Use cable coming with video switcher SW328: Dip Switch SW1: n 1, n 2 ON, n 3 ON, n 4 (HTML: Interfaces COM1) (HTML: Interfaces COM2) 16x4 Switcher Cablaggio: utilizzare una prolunga pin-to-pin maschio-femmina con connettori 9 poli a D Impostazione matrice: Utilizzare il connettore PC per collegarsi alla porta COM2 del codec VCS attraverso la prolunga maschio-femmina ed utilizzare la porta AUX della matrice per il collegamento con i ricevitori di telemetria DTRX3. La programmazione della matrice è disponibile sul manuale della stessa. Si consiglia di installare sempre almeno una tastiera nel sistema per procedere alla programmazione di tutti i parametri. Cables: pin to pin cable Switcher setting: Use PC connector and COM2 of VCS codec and use AUX port (of the switcher) to connect the telemetry receivers. (HTML: Interfaces COM2)
AuroraCorD AuroraCorD Terminator Box 3 Tx RS-232 RxD 2 Rx RS-232 RXT Utilizzare i cavi in dotazione per collegare la porta COM1 del DVR al Terminator Box. AuroraCorD: Al fine di operare correttamente, impostare la porta COM1 del DVR in modalità PRN/Host,, Baud rate: 1200. (HTML: Interfaces COM1 / COM2) Vicon Switcher (COM1) V1422 (KeyPad) 2 RxD- 3 Command out - 3 TxD - 6 Response in - 5 GND 8/2 GND 7 TxD + 1 Response in + 8 RxD + 7 Command out + Impostazione della matrice: La porta di comunicazione Keypad della matrice e la tastiera che si intende utilizzare compatibilmente con la porta 1 del codec VCS; si faccia attenzione ad impostare tutte le tastiere del sistema alla stessa velocità di comunicazione. In caso si utilizzino diverse tastiere V1311-DVC, si consiglia di utilizzare il distributore dati opportuno. Switcher Settings: Use the KeyPad connector and the distributor line if more V1300-DVC are connected. (HTML: Interfaces COM1)
DPLEX16II DPLEX16II remote in DPLEX 4 GND 5 GND 3 Tx 2 Rx 2 Rx 3 Tx (HTML: Interfaces COM1) Data Bits: 8 Parity: Interface Mode: CDR16T CDR-16T (HTML: Interfaces COM1) 1 Serial port function: 2 2 Transparent 3 3 4 5 5 6 7 8 QS-CXII QS-CXII remote 9 5 2 3 Tx 3 2 Rx 5 9 - (HTML: Interfaces COM1)
AFZC-22 AFZC-22 2 Rx 3Tx 3 Tx 2 Rx 5 GND 5 GND (HTML: Interfaces COM1) DPLEX16-ECO DPLEX16-ECO 23 Rx 3 Tx 11 Tx 2 Rx 1 GND 5 GND (HTML: Interfaces COM1) QD-04P QD-04P 6 Tx 2 Rx 1 Rx 3 Tx 9 GND 5 GND (HTML: Interfaces COM1)