Installation and ssembly: Desktop Mount with Desk Clamp and Grommet for 19" - 30" LCD Screens Models: LCT100S GROMMET INSTLLTION DESK CLMP INSTLLTION Max Load Capacity: 20 lbs (9 kg) 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com
NOTE: Read entire instruction sheet before you start installation and assembly. Tools Needed for ssembly phillips screwdriver drill 3/8" (10 mm) drill bit Table of Contents WRNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112. This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Never exceed the Maximum Load Capacity. See page 1. lways use an assistant or mechanical lifting equipment to safely lift and position equipment. Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power. This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury. Parts List...3 Installation to Mounting Surface...4 ttaching dapter Plate ssembly to Screen...5 Cable Management...6 2 of 6
efore you begin, make sure all parts shown are included with your product. Parts List Description Qty column assembly 1 adapter plate assembly 1 C grommet assembly 1 D round rubber pads 2 E square rubber pads 2 F M4 x 12 mm phillips screw 4 G M4 x 30 mm phillips screw 4 H M5 x 12 mm phillips screw 4 I M5 x 30 mm phillips screw 4 J spacer 4 K 4 mm allen wrench 1 L 2.5 mm allen wrench 1 M cable clip 1 N cable tie 5 Parts may appear slightly different than illustrated. C D E F G H I J L K M N 3 of 6
Clamp Installation Method 1 pply four rubber pads (D, E) to bottom of column assembly () as shown below. ttach column assembly () to mounting surface with a maximum thickness of 3". Skip to step four. Grommet Installation Method 1 Remove clamp assembly from column assembly () as shown in fi gure 1.1. Remove mounting plate from grommet assembly (C) and attach to column assembly () with four M6 x 8 mm screws using 4 mm allen wrench (K) as shown in fi gure 1.2. fig. 1.1 D E M6 X 8 MM SCREWS CLMP SSEMLY fig. 1.2 MOUNTING PLTE M6 X 8 MM SCREWS pply four rubber pads (D, E) to bottom of column assembly () as shown below. 2 3 Drill a 3/8" (10mm) dia. hole through mounting surface with a maximum thickness of 3". Place column assembly () on mounting surface and secure using grommet assembly (C). E D C 4 of 6
ttaching dapter Plate ssembly to Screen WRNING Tighten screws so adapter plate assembly is fi rmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. lb (4.5 N.M.) maximum torque. If screws don't get three complete turns into the screen inserts or if screws bottom out and plate is still not tightly secured, damage may occur to screen or product may fail. 4 To prevent scratching the screen, set a cloth on a fl at, level surface that will support the weight of the screen. Place screen face side down. If screen has knobs on the back, remove them to allow the adapter plate assembly to be attached. Place adapter plate assembly () on back of screen. Choose hole pattern as shown in detail 1. FOR DISPLYS WITH FLT CKS: ttach adapter plate assembly () to display using four 12mm screws (F or H) as shown in fi gure 4.1. FOR DISPLYS WITH RECESSED CKS: ttach adapter plate assembly () to display using four 30mm screws (G or I) and four spacers (J) as shown in fi gure 4.2. VES 100mm fig. 4.1 VES 75mm F,H VES 75mm VES 100mm DETIL 1 fig. 4.2 G,I J 5 of 6
5 Loosen and position lock collar to desired height and retighten lock collar as shown in fi gure 5.1. Insert adapter plate assembly () onto column assembly () and let it rest on lock collar as shown in fi gure 5.2. Tighten set screw on rear of adaptery plate assembly () using 2.5 mm allen wrench (L) as shown in fi gure 5.3. fig. 5.1 fig. 5.2 fig. 5.3 LOCK COLLR LOCK COLLR SET SCREW 6 Cables may be routed using cable clip (M). CLES M 6 of 6 2011 Peerless Industries, Inc. ll rights reserved. ll other brand and product names are trademarks or registered trademarks of their respective owners.