System Data V/IPedge Feature Description IPedge Feature Desc. 6/25/13 OVERVIEW IPedge System Data settings allow system administrators to set IPedge settings such as: Caller number display, and Ringing types Caller ID types, COS, DR, and Conference override privileges Caller ID, LCD Refresh rates, and DSS Ringing/DND Indication Dialing, ringing, and numbering plans Emergency Call (911 and E911) settings or service marks of their respective owners. This document and the information included herein is subject to change without notice. 1-1
System Data V/IPedge Feature Description IPedge Feature Desc. 5/17/13 System Data Enterprise Manager allows a system administrator to set IPedge system data settings. System Data settings are primarily global IPT settings. There is one setting for Class of Service (COS), the COS Override Code, to set the digit length of the COS code. or service marks of their respective owners. This document and the information included herein is subject to change without notice. 1-2
System Data V/IPedge Feature Description IPedge Feature Desc. 6/25/13 System Data Not applicable. or service marks of their respective owners. This document and the information included herein is subject to change without notice. 1-3
System Data V/IPedge Feature Description IPedge Feature Desc. 7/25/13 PROGRAMMING System Data Settings are accessible via Enterprise Manager: System > System Data. Executive Override Enable/Disable break-in warning tone for Executive Override Settings: Enable/Disable (Default: Enable) Station MOH Source Music on-hold selection for Trunks and Stations. Refer to System > Music On Hold for system MOH assignments. MOH for trunks is set in the DID assignments. Settings: Music (source) 1 ~ 15, Beep Tone, and Quite Tone Ring Transfer Tone Select tones for the ringing party to hear after ring transfer OR off-hook campon. Settings: RBT (default) or MOH Transfer Privacy Enabled: CO buttons that have Multiple Appearances will only flash and ring on the transferred-to IPT. Disabled: CO buttons that have Multiple Appearances will flash and ring on all IPTs that have CO button Line Appearance Privacy Override This feature setting is enabled in Class of Service (COS). A station with Privacy Override may barge into a conversation and establish a conference by pressing an in-use line key. Important! Enabling this setting via System Data enables or disables a break-in/warning tone to let the existing members of the call know someone else has overridden the privacy and joined the call Settings: Enable/Disable (Default: Enable) Credit Card Code Credit Card Digits Enter the number dialed to initiate a credit card call. This is normally 0 in the USA. Settings: Up to 32 digits; Default: null Enter the minimum dial digits required for Credit Card calling. This is the quantity of digits in the credit card number. If this quantity of digits is not dialed when making a Credit Card call, the caller will be disconnected. This provides a mechanism to ensure that the call is charged to a credit card. Possible Values: 1-32 E911 Service Enable E911 service Availability. Settings: Enable/Disable (Default: Enable) or service marks of their respective owners. This document and the information included herein is subject to change without notice. 1-4
System Data V/IPedge Feature Description IPedge Feature Desc. 7/25/13 DR Override by SSD Enable DR Override by system speed dial. Settings: Enable/Disable (Default: Enable) If enabled, calls made using a System Speed Dial will override Toll/Destination Restriction. Auto Station Release Lost Call Destination Not used Lost Call Treatment provides the IPedge a mechanism for terminating calls that cannot be terminated with the usual calling patterns. One scenario would be a call that is recalled to a station, the station user is no longer there to answer the recall and no forwarding pattern is programmed. The call will ring at the recalled station until the Lost Call Timer has expired after which the system will direct the call to the Lost Call Destination. Value: up to five digits (Default: null) COS Override Code Multi-Conference Length of CoS override codes Values: 1-9 (default: 1) Enable of Disable multi-conference capability for internal or outgoing calls. Settings: Enable/Disable (Default: Enable) Caller Number Display Display Preference Transit Counter If a softkey competes with Caller ID, the Caller ID number will be displayed - if enabled, otherwise, soft-key will persist. Settings: Enable/Disable (Default: Enable) Select whether to display DNIS, or caller ID. Default: (DNIS) The Transit Counter limits the number of nodes that a call can traverse before being terminated as a lost call. Note: This value should always be one more than the number of nodes in an IPedge Net; for a standalone system the value should be 1 Values: 1-128 (Default: 1) Call History Prefix Add the dialing prefix 1 when using the Callback Feature in Call History. Values: Add (default) Do Not Add Emergency Digits Sent DP Make Ratio Enter an Alternative Emergency dialing sting. If no value is entered in this field, any previously entered value will be overwritten. Values: 1-5 digits (default = 911 ) Not used or service marks of their respective owners. This document and the information included herein is subject to change without notice. 1-5
System Data V/IPedge Feature Description IPedge Feature Desc. 7/25/13 Call Button Jumping If enabled, line calls move from a DN button to a Line Button after they are answered. The DN button is then cleared to receive another call. The DN effectively acts as an answer button for the IPT Note: Operation only applies if line answered has a CO, GCO, or Pooled Line button appearance on the IPT. Disable: Line Calls remain on the DN after answer. Settings: Enable/Disable (Default: Enable) Standard Ringing Cadence Sys CF Cascade Not used System Call Forward Cascade, which when enabled, means that a call that forwards to a destination that is also forwarded will follow the destination s call forward. For example: Station A is assigned System Call Forward to Station B which also has System Call Forward assigned. When enabled, a call which forwards from station A to station B would follow the forwarding of station B when the call forward timer expired. When disabled, a call forwarded from Station A would not follow the forwarding assigned to station B. CSTA B-Ch. Operation CSTA provides full B channel path information. If disabled, CSTA will provide Channel Group only. Repeat Last No. Dialed Enable: Store incomplete and complete numbers in the Last Number Dialed buffer Disable: Store only complete numbers in the Last Number Dialed buffer Default Calling Number Enabled: The system will send the default calling number to the SIP Trunk Provider when stations make SIP Trunk calls on the local node. Disable: System will not send default calling number. Values: Enable / Disable (Default: Disable) DSS Ringing/DND Indication Select the DSS LED pattern: Ringing: DSS will flash red when DN is ringing, o in DND mode Idle: LEDs will NOT flash red, and remain idle (unlit) when DN is ringing; DSS LED will flash red if in DND mode. Idle (DND On): Same as Idle, however, DSS LEDs will be solid red (no flashing) to indicate DND mode. Values: Ringing (default), Idle, Idle (DND-On) or service marks of their respective owners. This document and the information included herein is subject to change without notice. 1-6
System Data V/IPedge Feature Description IPedge Feature Desc. 7/25/13 Caller ID Call Types If this feature is not selected for a call type, the DN of the calling station will display on the IPT instead of Caller ID. ISDN CPN Number Type ISDN Calling Party number type of Number Setup message format Values: System Default, Unknown, Int l, National, Network, Subscriber ISDN CPN Numbering Plan ISDN Calling Party Numbering plan ID setup message format. Values: System Default, Unknown, ISDN, Data, Telex, National, Standard, Private. LCD Keystrip Refresh Interval Caller ID Line Access Code Time in hours between refresh commands send to the LCD. Values 0-24 (Default: 0) Line or Trunk Access Code that the IPT will dial to access an outside line when the caller ID softkey to dial a selected Caller ID number. Default: 9 Automatic Location Management When enabled, sends the IPT terminal information to the E911 service. or service marks of their respective owners. This document and the information included herein is subject to change without notice. 1-7
System Data V/IPedge Feature Description IPedge Feature Desc. 5/17/13 CAPACITY N/A AVAILABILITY N/A RESTRICTIONS N/A or service marks of their respective owners. This document and the information included herein is subject to change without notice. 1-8
System Data V/IPedge Feature Description IPedge Feature Desc. 5/17/13 HARDWARE No additional hardware is necessary for this feature. or service marks of their respective owners. This document and the information included herein is subject to change without notice. 1-9
System Data V/IPedge Feature Description IPedge Feature Desc. 6/25/13 FEATURE INTERACTION Feature interaction is described in the parameter descriptions. or service marks of their respective owners. This document and the information included herein is subject to change without notice. 1-10