E M C C o m p o n e n t s November 0 -terminal Filters For signal line MEM series MEM0S MEM0SC MEM0V MEM0F MEM608P 0[0805 inch]* 0[0805 inch] 0[0805 inch] 0[0805 inch] 608[060 inch] * Dimensions Code JIS[EIA]
(/5) REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than months. Be sure to follow the storage conditions (Temperature: 5 to 40 C, Humidity: 0 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 50 C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. () Aerospace/Aviation equipment () Transportation equipment (cars, electric trains, ships, etc.) () Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (0) Electric heating apparatus, burning equipment () Disaster prevention/crime prevention equipment () Safety equipment () Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment.
(/5) -terminal Filters For signal line Overview of the MEM Series Product compatible with RoHS directive Halogen-free Compatible with lead-free solders FEATURES Multilayer chip EMC filter. Monolithic structure makes it highly reliable. Closed magnetic circuit structure makes it possible to achieve high-density mounting without crosstalk. Has sharp attenuation characteristics with excellent EMC suppression. Wide range of products compatible with passing frequencies and attenuating frequencies. MEM0S T-type circuit is used. MEM0SC T-type circuit is used. Compatible with A current. MEM0V Double type circuit is used. Sharp attenuation characteristics. MEM0F type circuit is used. MEM608P type circuit is used. Compact with a low profile design. APPLICATION Noise removal from signal lines of data terminals, digital cameras, computers, game machines, flat TVs, etc. PART NUMBER CONSTRUCTION MEM 0 S 5R0 T Series name L W T Dimensions Product internal Cutoff frequency (mm) code (MHz) Packaging style 608.6 0.8 0.6 S 5R0 5 T Taping 0.0.5 0.8 SC 0R 00.0.5 0.85 V F Capacitance P (pf) at MHz 00 0 0 00 MEM0SC only Internal code OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type Operating temperature Temperature range Storage temperature Package quantity Individual weight C C pieces/reel mg MEM0S 40 to +85 40 to +85 4,000 8 MEM0SC 40 to +85 40 to +85 4,000 8 MEM0V 40 to +85 40 to +85 4,000 8 MEM0F 40 to +85 40 to +85 4,000 8 MEM608P 40 to +85 40 to +85 4,000.5 The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 500ppm.
(4/5) Overview of the MEM Series RECOMMENDED REFLOW PROFILE Preheating Soldering Peak T4 Natural cooling T: Temperature T T t T T t t t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T T t T t T4 t 50 C 80 C 60 to 0s 0 C 0 to 60s 50 to 60 C 0s max.
(5/5) MEM series MEM0S Type SHAPE & DIMENSIONS ±0. 4 0.min..5±0. IN/OUT OUT/IN 0.min 0.min 0.4±0.5 0.4±0.5 0.4±0.5 RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 0.85±0.5 0.4.4.6
(6/5) MEM series MEM0S Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Cutoff frequency Insertion loss Rated voltage Rated current (MHz) (db)min. (V)max. (ma)max. Part No. 5 0[70MHz to GHz] 0 00 MEM0S5R0T 5 0[90MHz to GHz] 0 00 MEM0S5R0T 50 0[00MHz to GHz] 0 00 MEM0S50R0T 00 0[400MHz to GHz] 0 50 MEM0S0RT 00 0[50MHz to GHz] 0 50 MEM0S0RT Measurement item Product No. Manufacturer Frequency characteristics N50C Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 0 0 Insertion loss (db) 0 40 50 5R0 5R0 0R 50R0 0R 60 70 0 00 000 0000 Frequency (MHz) Product No. Manufacturer N50C Agilent Technologies
(7/5) MEM series MEM0SC Type SHAPE & DIMENSIONS NC 6 ±0. 5 NC 4.5±0. 0.min. IN/OUT OUT/IN 0.min. 0.min. 0.8+0.5, 0. 0.4±0.5 0.4±0.5 0.4±0.5 RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM. 0.5 0.4..6
(8/5) MEM series MEM0SC Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Capacitance (pf) Tolerance (%) Measuring frequency: (MHz), measuring voltage: (V) Rated voltage (V)max. Rated current (A)max. DC resistance ( )max. Terminal No. to Part No. 0 ±0 0.5 MEM0SC00T ±0 0.5 MEM0SC0T 47 ±0 0.5 MEM0SC470T 00 ±0 0.5 MEM0SC0T 50 ±0 0.5 MEM0SC5T Measurement item Product No. Manufacturer Capacitance 494A Agilent Technologies Frequency characteristics N50C Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 0 Insertion loss (db) 0 0 40 SC5 SC0 SC00 SC0 SC470 50 60 0 00 000 0000 Frequency (MHz) Product No. Manufacturer N50C Agilent Technologies
(9/5) MEM series MEM0V Type SHAPE & DIMENSIONS ±0. 4 0.min..5±0. IN/OUT OUT/IN 0.min 0.min 0.4±0.5 0.4±0.5 0.4±0.5 RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 0.85±0.5 0.4.4.6
(0/5) MEM series MEM0V Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Cutoff frequency Insertion loss Rated voltage Rated current (MHz) (db)min. (V)max. (ma)max. Part No. 0 0 [00MHz to GHz] 0 00 MEM0VRT 50 0 [50MHz to GHz] 0 00 MEM0V5RT 80 0 [00MHz to GHz] 0 00 MEM0V8RT 0 0 [50MHz to GHz] 0 00 MEM0VRT 40 0 [450MHz to GHz] 0 00 MEM0V4RT 00 0 [550MHz to GHz] 0 00 MEM0V0RT Measurement item Product No. Manufacturer Frequency characteristics N50C Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 0 Insertion loss (db) 0 0 40 50 R 5R 8R R 4R 0R 60 70 0 00 000 0000 Frequency (MHz) Product No. Manufacturer N50C Agilent Technologies
(/5) MEM series MEM0F Type SHAPE & DIMENSIONS ±0. 4 0.min..5±0. IN/OUT OUT/IN 0.min 0.min 0.4±0.5 0.4±0.5 0.4±0.5 RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 0.85±0.5 0.4.4.6
(/5) MEM series MEM0F Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Cutoff frequency Insertion loss Rated voltage Rated current (MHz) (db)min. (V)max. (ma)max. Part No. 0 0 [00MHz to GHz] 00 MEM0F0R0T 5 0 [00MHz to GHz] 00 MEM0F5R0T 50 0 [400MHz to GHz] 00 MEM0F50R0T 75 0 [700MHz to GHz] 00 MEM0F75R0T 00 0 [.5GHz to GHz] 00 MEM0F0RT Measurement item Product No. Manufacturer Frequency characteristics N50C Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 0 0 Insertion loss (db) 0 40 50 0R0 5R0 50R0 75R0 0R 60 70 0 00 000 0000 Frequency (MHz) Product No. Manufacturer N50C Agilent Technologies
(/5) MEM series MEM608P Type SHAPE & DIMENSIONS.6±0. 4 0.min. 0.8±0. IN/OUT OUT/IN 0.5min 0.5min 0.6±0. 0.±0. 0.5±0. 0.±0. RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 0.. 0.8 0. 0. 0.9.0
(4/5) MEM series MEM608P Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Cutoff frequency Insertion loss Rated voltage Rated current (MHz) (db)min. (V)max. (ma)max. Part No. 5 0[70MHz to GHz] 0 00 MEM608P5R0T 5 0[90MHz to GHz] 0 00 MEM608P5R0T 50 0[00MHz to GHz] 0 00 MEM608P50R0T 75 0[00MHz to GHz] 0 00 MEM608P75R0T 00 0[400MHz to GHz] 0 00 MEM608P0RT Measurement item Product No. Manufacturer Frequency characteristics N50C Agilent Technologies INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 0 0 Insertion loss (db) 0 40 50 60 5R0 5R0 50R0 75R0 0R 70 80 90 0 00 000 0000 Frequency (MHz) Product No. Manufacturer N50C Agilent Technologies
(5/5) MEM series Packaging style REEL DIMENSIONS.0±0.5 ø60min..0 ø80±.0 ø±0. ø±0.8 8.4 +.0 0.0 4.4max. TAPE DIMENSIONS.5 +0. 0.0±0.05 4.0±0. B.75±0..5±0.05 8.0±0. A 4.0±0. K Type A B K MEM0S.55±0.0.0±0.0.0max. MEM0SC.55±0.0.0±0.0.0max. MEM0V.55±0.0.0±0.0.0max. MEM0F.55±0.0.0±0.0.0max. MEM608P.0±0.0.90±0.0 0.90max. 60min. Taping 00min. Drawing direction 00min. MEM0S, MEM0V, MEM0F MEM0SC MEM608P