RESISTOFLEX GMBH flanged pipe, fittings and hoses are all without exception lined with seamless fluorocarbon resins like PTFE (Polytetrafluorethylen) and PFA (Perfluoralcoxy). This leads to the most advanced linings which are attainable. The patented THERMOLOK-Process guarantees, in connection with years of practice and manufacturing, world-wide top quality and therefore a high factor of safety and a very long life of the installed parts. RESISTOFLEX-PTFE-linings are relaxed and braced thermally inside the housings. This compensates the different expansion factors between steel and FLUOROFLEX -PTFE and no folds or cracks will occur. Modern quality assurance methods are used which create repeatable quality over the future years. RESISTOFLEX GMBH have the TÜV-approval according to ISO 9001:0. Furthermore we offer E-certificates for all lined pipe and fittings, acc. to catogory III, module B plus 1. Many checks and production supervision are existing such as incoming goods, raw materials, semifinished products and final testing. At some departments EDP supported data are elaborated or stored. The existing catalogue with all of its principle drawings shows the offered products and data. Furthermore it is information for producers, distributors and users and to promote understanding between buyers and sellers. The nominal pipe size NPS is mainly used as criterion. Based on technical reasons these NPS correspond only approximately to the true inside diameters of the lined pipe and fittings. 1. Introduction 2.1 Product range RESISTOFLEX GMBH offers flanged pipe, fittings, chemical transfer hoses etc. as per the following range: - Nominal pipe size DN 0 to DN - Nominal pipe size NPS 1/2" to NPS 24" - particular pipe spools up to DN / NPS 24" - products acc. to DIN 2848 / 287 reduced correlation utilizat. - products acc. to ASME / ANSI B16.5 lass 1 and - other pressure classes in DIN as PN16, PN or PN - lined pipe in single length of 6 meters / feet - variable wall thickness of liners up to mm / 6 inch - high vacuum resistance of all sizes - homogeneous, seamless linings - all parts producible in electrostatically nonchargeable PTFE or PFA - working ranges from 30 / F to +260 / +4 F Please take single values from the product data sheets and the technical data. 2.2 Linings Only virgin fluorocarbon resins will be used. They meet the following specifications : - ASTM D-4894 Granular resin PTFE - ASTM D-4895 Paste / fine powder resin PTFE - ASTM D-3307 Type II PFA - DIN 2874 Flanged pipe and fittings - GKV Quality requirements The linings and dimensions meet: - DIN 2848 PTFE / PFA - ASTM F-45 PTFE / PFA The temperature rates for PTFE and PFA lined parts are between 30 / F and +260 / +4 F. Owing to the shape or reinforcement these temperature rates may be reduced on some of the products. As a rule PTFE parts are manufactured in virgin white. Black coloured paste liners are also available. PFA parts are in virgin opaque. Electrically conductive linings from PTFE are dark black. 2. Technical Data TDS-EU-DIN-A-E-04
3.1 Physical Values Physical values are taken from semi-finished products, tensile specimen or films, after production by RESISTOFLEX GMBH. hemical and physical resistance are acc. to ASTM - D 543. If you need more information, we will obtain this from the resin manufacturers. Property Unit Value Value PTFE- PTFE- Granulat white Paste white Value PFA Method of Inspectio n specific gravity gr / cm3 2,13 2,18 2,13 2,18 2,13 2,16 DIN 53 479 tensile strength N / mm2 > > 26 > 21 DIN 53 455 / SPI FD-105 e longation % > 270 > 275 > 0 DIN 53 455 / SPI FD-105 tensile Modulus N / mm2 7 7 700 DIN 53 457 compressive strength : 1% yield point N / mm2 5 5 5 DIN 53 454 10% yield point N / mm2 18 18 thermal conductivity coefficient of linear thermal expansion urface resistivity s 0 volume resistivity 0 flammability permeability qg permeability coeff. PG W / m x K 35 35 35 DIN 52612 K -1 5 17 x 10-17 x 1 0-5 17,5 x 1 0-5 DIN 52 32 8 cm / min 1 2 1 2 5 x 1 4 DIN 53 48 2± 1 0 2± 1 0 1 2 1 2 1 2 1 6 DIN 53 48 2± 1 0 2± 1 0 1 2 self-extinguishin g DIN 53 459 c m 3-0 0 2 000 m 2 x 24h x bar DIN 53 3 / 5353 6 c thickness of sample m 3 ( 1-3) x 1 0-6 ( 1-3) x 1 0-6 0-6 ( 1-3) x 1 s = 2 mm m x sec x cmhg 3. General properties of virgin PTFE and PFA 3.2 Tensile-/elongation diagrams of PTFE-finepowder, s=2,4 mm, sample acc. to SPI FD-105. ε (%) 275 σ Ρ 30 N/mm 2 χα. ca. ε (%) 275 χα. ca. longitudinal τρανσϖερσαλ transversal 3.3 Administation registered application 2 σ Σ Ν /µµ N/mm 2 σ Ν /µµ 2 Σ N/mm 2 σ (N/mm (Ν/µµ 2 ) 2 ) (N/mm 2 ) σ (N/mm (Ν/µµ 2 ) 2 ) Fluoropolymer resins PTFE and PFA used by RESISTOFLEX GmbH for linings are also selected acc. to a.) production in compliance with the Federal lean Air Amendment of 1990 and are not damaging to the environment nor must carry labels and b.) are released as articles intended to contact food, as indicated below. - 90 / 128 / EWG, 92 / 39 / EWG, 93 / 9 / EWG, - Bedarfsgegenständeverordnung vom 10.04.92, - FDA 21 FR 177. The responsibility for testing and for suitability of the products, shipped by us regarding the application or installation remains with the user. Medical applications are not allowed without permission. As far as admixtures exist in the linings, they consist of industrial manufactured amorphous carbon black or are authorized acc. to the above mentioned licences. σ Ν /µµ 2 Ρ 30 N/mm 2
3.4 Time yield limit of PTFE - liner between +23 and +1 3.5 Maximum pressure ratings The chart below indicates the maximum pressure ratings for fluorcarbon plastic lined carbon steel pipe and fittings. at Temperature ( ) DIN ( bar ) DIN PN ( bar ) -10 1 5 32, 5 13, 5 30 70 12, 5 28 12 26, 5 1 11, 5 1 1 5 23 9, 5 0 8 17 TDS-EU-DIN-B-E-04
4.1 Steel pipe Steel pipe are either seamless or welded. They meet the following specifications : - St 37.0 = 1.04 - St 35.8 = 1.0354 4.2 Fittings are assembled from parts acc. to : DIN 2605 / 2606, Teil 1 DIN 26, Teil 1 DIN 2616, Teil 1 for elbows for tees for reducers or welded from steel pipe. Some of the parts are also machined; for these, the materials are RSt 37-2 or H II. 4.3 Flanges Variants : - welding neck flanges acc. to DIN 2632 - lapped joint short stub end and loose flanges acc. to DIN 2673 - slip on welding flanges acc. to DIN 76 - collar and lapped flanges acc. to DIN 2642B The used materials are : - RSt 37-2 / 1.0038 - H II / 1.04-22.8 / 1.0460 4. Pipe, Fittings and Flanges 4.4 Screws and Nuts The quality of screws / nuts being used in the case of assembled parts that are screwed together in the plant corresponds to DIN 267. For screws applies strength class 4.6 respectively 5.6 in steel as well as A2 respectively A4 in alloy steel. For nuts applies strength class 5 in steel as well as A2 respectively A4 in alloy steel. Hexagon socket head screws DIN 912 are only available in class 8.8, 12.9 or A4. Stud bolts DIN 938 will be offered in class 5.8 or A2. 4.5 Earthing studs allow the external earthing of the pipe system and are availabele on Value and on Select series. The studs are welded in the middle of the steel fitting or spool with a length of less than 0mm. For longer spools or fittings the stud is welded at 1 mm behind the flange. The material used for earthing studs is stainless steel. The dimensions of the suds are a M6 thread mm long. Vent extenders allow the venting system to perform through the insulation. With vent extenders it is also possible to collect the permeant. Vent extenders are available on Value and on Select Sereis. The vent extenders are welded in the middle of the steel fitting or spool with a length of less than 0mm. For longer spools or fittings the vent extender is welded at 1 mm behind the flange. The standard vent extender has a 1/8 NPS thread and a outer diameter of 19mm. It is 16mm long and the used material is St37. onductive or antistatic PTFE liner has a black carbon additive that allows for the dissipation of static electricity through the PTFE liner to the metal pipe or fitting wall. onductive liner is available in the Select Sereis only. onductive liner thickness are 6% - 8% less than for non-conductive liner. The physical values of conductive liner are approximately % lower than for non conductive liner.
The tolerances of the lined products observe the specification of DIN 2848 / 2874. Further details are contained in the single information sheets 5. Tolerances The marking of the products is permanent. It is made according to DIN 2848 / 2874. Special requests are possible. With the exception of some red.-flanges, blind-flanges and the solid PTFE parts, all lined pipe and fittings are provided with vent holes. These have diameters mostly from 3 to 4 mm. They serve to inspect after production as well as to indicate leaks when working. Depending on service conditions vent hole extensions with an internal thread could be welded on. This opens the possibility to either compensate for insulation, suck off permeation or to close them by screws to avoid environmental pollution. If vent hole extensions will be used, one per part is sufficient. We recommend to keep the vent holes always open. losed vent holes may cause collapsing of liners, due to permeated gas between lining and housing. 6. Marking 7. Vent Holes Metal surfaces on the outside of flanged pipe parts are subjected to steel shot blasting SA 2.5 and treated with zinc rich epoxy primer. Multilayer coatings tend to cracking while fixed at site; we do not recommend them. 8. Protective oating All assemblies have their flared gasket faces covered with end plates secured by either clips or metal bolts. This serves to protect the lining, to keep the flared face down as well as to maintain the interior clean. Parts with injected plastic (PFA) or isostatically pressed PTFE-gasket faces can be protected by plastic caps. The final inspection of the finished products occurs in several ways. First of all by visual control as to clean and good surfaces and subsequently by dimensional control of length, flange face, threads, check of marking etc. Finally a pressure and tightness test according to the shape and dimension is carried out. % of all parts are checked at room temperature as follows : - straight pipe = 14 x 10 5 Pa hydraulically or pneumatically - elbows = 14 x 10 5 Pa and 35 kv D - tees, crosses, instrument tees = 14 x 10 5 Pa and 35 kv D - chemical transfer hoses = 1,5 x nominal pressure - industrial hoses = 1,5 x working pressure - others = 35 kv D or according to agreements Pressure tests according to ASTM F-423 and F-781 (elevated pressure) are only carried by agreement. Special checks in warm water bath with outside pressure or vacuum checks under raised temperatures are possible. 9. Flange Protectors 10. Final Inspection TDS-EU-DIN--G-04
11.1 At the passage of media through pipe parts or flexible hoses static electric charges may form. In order to avoid these charges that may lead to spark formation and possibly to the ignition of gas-air mixtures, the PTFE-lining must allow electrical discharge. RESISTOFLEX GMBH produces upon special request lined pipe parts or fittings and flexible hoses that allow flow of static electricity. 11.2 Values The values refer only to PTFE powders that are adjusted to be electrically conductive. They apply both to the inside and outside surface and to the passage through the PTFE wall. As soon as the lining comes into contact with the armoured parts, i.e. pipe, hose, etc., flow of the charge through these occurs; this discharge takes place through metal parts and is therefore smaller than 10 6 Ohm. RESISTOFLEX GmbH produces PTFE linings having surface resistivities in the range between 10 4 and 10 8 Ohm. This is according to the Directions to avoid ignition danger as a result of electrostatic charges of the trade associations, committee of experts for chemistry, ZH 1/. Measuring is being carried out according to DIN 53 482 and / or ASTM D7. The following definitions apply : 11. Surface resistivity on PTFE-Linings 1. Volume resistivity R A = 1 x 10 6 bis 5 x 10 8 (Ω x cm 2 ) referred to an electrode surface of diameter 22 or diameter 49,5 mm according to 5 or cm 2. 2. Volume resistance R D in (Ω ) that is multiplied by the electrode surface. R D = 1 x 10 6 bis 1 x 10 8 (Ω ) 3. surface resistance R O is being measured. It gives information on the insulation condition on the surface of a material. R 0 = 1 x 10 6 bis 5 x 10 8 (Ω ) 11.3 Volume and surface resistivities The Volume and surface resistivities acc. to DIN 53 428 are within 10 4 and 10 6 Ohm for PTFE - granular resin and within 10 6 and 10 8 Ohm for PTFE - fine powder resin, depending on the kind of product. Electrically conductive PTFE - linings normally yield wallthicknesses which are 6 % to 8 % thinner than white ones. The physical values are also reduced to a level of approx. % below. 11.4 We furthermore would like to inform you, that for some liquids it might occur, that it absorbs the carbon black off the PTFE and could be contaminated.
Lined products must not be welded, brazed or torch-cut since this may damage the lining. For shipment all flanges are protected by covers to prevent damaging during transport and storage. These covers should only be removed shortly before installation. If dismantled for inspection they should be replaced immediately. It is not necessary to use gaskets between the PTFE sealing faces. If, however, flares are connected to sealing faces of other materials, such as glass, ceramics, carbon, or metal, and where the flares may not be parallel, it is recommended that an additional PTFE gasket be employed. This gasket should be 5 mm thick. It can absorb unevenness. Excessive bolt tightening during assembly can deform the sealing face. To avoid this, the following bolt torques should not be exceeded. See table below for allowed torques. 12.1 Bolt torques of the flange screws to DIN for PN 1 PN 16 and PN are shown in the table below. These torque values are valid for lightly oiled bolts according to quality 5.6 / 5 and evtl. washers. orroded threads may increase the torque values ineffective or even double them. Tighten the flange bolts with a torque wrench, using a crisscross pattern that alternately tightens the bolts located 1 apart. Using this pattern, tighten the bolts in % increments of the final bolt torque until % of the final bolt torque has been achieved. For tightening to the final torque values, tighten bolts sequently clockwise once around the flange. This will help ensure that the bolts are evenly stressed. 12. Installation and Maintenance Instructions for Lined Pipe, Fittings, Transfer Hoses and Expansion Joints Dimension DN bolts PN10 PN 16 PN bolt torque Nm bolts bolt torque Nm bolts bolt torque 0-0 4 x M12 4 x M12 4 x M12 032-0 4 x M16-38 4 x M16 35-53 4 x M16 35-53 4 x M16 45-4 x M16 45-4 x M16 45-4 x M16 46-70 4 x M16 46-69 8 x M16 46-69 8 x M16 48-70 8 x M16 48-72 8 x M16 48-72 8 x M16-75 8 x M16-75 8 x M 55-83 1 8 x M16-110 8 x M16-1 8 x M24 110-1 1 8 x M 90-135 8 x M 90-135 8 x M24 1-172 8 x M 1-170 12 x M - 1 12 x M24-1 0 12 x M 95-145 12 x M24 110-1 12 x M27 1-1 12 x M 1-190 12 x M24 1-2 16 x M27 1-2 3 16 x M 1-245 16 x M24 160-2 16 x M30-3 0 16 x M24 5-275 16 x M27-3 16 x M33 5-4 0 x M24 160-2 x M30-3 x M33 2-385 x M27 190-3 x M33 235-4 x M36 290-510 Nm TDS-EU-DIN-D-E-04
A retorque should be applied a minimum of 24 hours after the initial torque or after the first thermal cycle. This allows for seating of the plastic and for relaxation of the bolts. If the system is to perform at elevated temperatures, it is recommended that hot water be circulated at the maximum operating temperature of the process if possible for a minimum of 24 h. This allows for the pipe system to experience one thermal cycle. After cool-down, retorquing of the system should be done. Torquing should only be done on the system in the ambient, cooled state, never while the process is at elevated temperature or excessive force could be applied to the plastic faces. Retorque should be done annually thereafter especially if the process line experiences elevated temperatures or extreme ambient temperature situations. Frequency of retorque depends on application. Vibration, bolt strenth or number of thermocycles are important. ontinous processes need less retorque. old flow of flare material is shown under 3.3 of this specification. All lined products have small vent holes. It is important that these are not be blocked by insulation or plugged by paint as this may cause the lining to collapse. These vent holes also serve as early warning leakage indicators.the number of vent holes may be reduced if necessary. Those which remain could be provided with screwed couplings to either closed with nipples or connected to a vacuum pump. To avoid damage to the sealing faces, pipes and fittings should only be dismantled below +. If a flange connection leaks even though all bolts are tight, DO NOT TIGHTEN UP ANY MORE. Never exceed the above mentioned bolt torques. Loosen the bolts opposite the leak and tighten up the other side. If leakage persists, the sealing faces should be inspected for grooves or chips. Grooves or nicks not deeper than approx. % of the flare thickness can be removed with fine-grained abrasive paper. 12.2 Maximum pressure ratings This chart indicates max. pressure ratings for PTFE lined carbon steel pipe and fittings as indicated in this catalogue. PN Temp. 10 1 0 Pressure bar 10 10 8 7 Pressure bar 18
13.1 Permeation Ratings Permeation on different kinds of fluoropolymer linings;comparison. 13. Permeation The test conditions are as follows: Material - surface of samples = cm 2 - test medium = Helium - test pressure p = 2 bar Thickness of Sample mm PFA - Film 2, 3 PTFE - Ram 4 PTFE - Granulat 4 PTFE - Paste 4 Temperatur e Time of Tes t / F h Permeation dm 3 m2 x 24h x bar / 77 382 ca. 5, 3 85 / 185 84 ca. 22 / 77 382 ca. 3, 3 85 / 185 84 ca. 30 / 77 382 4-1, 2 85 / 185 84 1,4-7 / 77 382 3-1 85 / 185 84 1,5-5.2 Permeation, migration of molecules through the lining wall Diffusion is a spontaneous transport of medium caused by thermodynamic forces to compensate for concentration differences. The media migrates in the direction of decreasing concentration. Of practical importance is the permeation through finite wall thicknesses with measured values for judgement. How now does the permation of a molecule through a plastic wall happen and which are the most important parameters? A molecule inside the tube wall exerts almost elastic vibrations against it. With it energy must be supplied to overcome the linkage forces in the plastic or to move through socalled free spaces (no voids). PTFE is a hypocrystalline substance and the so-called free spaces are to be found in the amorphous part. rystalline zones are not penetrated. A series of influences causes individually or together the permeated quantity. It is presumed that both from liquid media and from gases only the gases permeate. The moving forces with it are the concentration or the partial pressure. In the case of substance mixtures both single components and their interactives may migrate. Little molecules get easier through so-called free spaces than big ones. hain molecules as well permeate easier than branched ones, since their cross-sectional area is smaller. A temperature increase supplies energy; this increases vibrations in the wall and in the media. Thus the activity of the molecules increases, the wall expands and possibly the amorphous part of the wall PTFE increases and as a result more molecules move quicker through. We get into a limit area when a media has a similar or equal polarity as the lining. Then the liquid may partially dissolve in the wall; it is then spoken of a swelling. With it the space between the macromolecules of the wall increases, that is more and greater free spaces develop. All molecules move then quicker through the wall even if only one generates the swelling. The thicker the lining is, the smaller is the permeation. High crystallinity reduces permeation. Greatest caution is anyhow advisable here, since as manufacturers we always aspire to an optimum between permeation and durability with regards to crackings in the PTFE; high crystallinity reduces flexibility and increases drastically the risk of fracture. FLUOROFLEX products always guarantee durability, low permeation values and operational reliability. TDS-EU-DIN-E-E-04
In general PTFE is chemically inert. We therefore differentiate between chemical reaction and physical behaviour. That is why in the following we deal with the physical interaction between plastic and contacting media. Submicroscopic little spaces between the polymer molecules make it for some substances, as e. g. water vapor, monomeres etc., possible to diffuse into the PTFE. By this the spontaneous media transport caused by pressure and temperature is meant. The medium moves in the direction of decreasing concentration. Absorption means here that a liquid diffuses into the PTFE and that the quantity increases with increasing pressure and increasing temperature. If a lined tubing part is subjected to cyclic pressure and temperature loads, so that the liquid entrapped in the plastic wall evaporates or condenses, then the resistance of the plastic may be reduced at several points. This originates bubbles that in the course of time develop into so-called blisters. The PTFE there suffers a locally limited delamination. FLUOROFLEX-PTFE linings are brought into an optimal condition. Only raw material having on one hand a sufficient flexibility and on the other a relatively high share in crystalline PTFE are being used. The situation is additionally aggravated by the great operative temperature range of PTFE and the thermal fluctuation originating with it between operation and standstill. It is presumed that owing to the pressure drop vapour penetrates in the PTFE, and since there prevails a great temperature drop the vapour condenses in the wall. During cyclic operation, that is stop and restart, the entrapped condensation quantities are being expanded with rising temperature, their volume increases and the plastic is being locally laminated. Depending on this condition the formation of bubbles or blistering proceeds. This anyhow leads not at all or only after a comparatively long time to the total failure or outage of parts, since blisters mostly lie in the inner third of the wall, that is maintained in its function as separation layer. How can we reduce this phenomenon? Since mostly the process condition cannot be changed, an insulation of the tubing parts usually clearly improves the situation or even avoids these blisters completely, the insulation of the flange area or other metal suspensions being there particularly important. The insulation avoids the great temperature drop and thus the condensation that is later expansion. A qualifying test for PTFE is therefore also the so-called vapour-cold water test according to ASTM F-423. Papers treating this subject are: - Du Pont, reprint of the Journal of Teflon Nr. 1-D-2; A-62722-2. - Du Pont, Teflon/Tefzel, protection against corrosion in chemistry H-11959-2. - ASTM F-423 - NBS Voluntary Product Standard PS 33-70 des US Department of ommerce All data shown in this catalogue according to our best knowledge but does not constitute any form of guarantee. Recommendations for use are only advisory. They do not release the user from his obligation to prior check the delivered products concerning their safety and readiness for use. 14. PTFE Absorption Behaviour in hemical Aplication. General Information
16. Pressure Dimensions - compared between atmosph. Pressures and full Vacuum PA MPa 2 1 Pa = 1 N/m 1 0 bar mbar m WS mm WS mm Hg psi 2 kp / cm 2 2 N / m MN / m ( Torr ) ( at ) 1-6 10-5 10-2 1,02 x 1 0-4 1,02 x 1 0-1 7,5 x 1 0-3 1,45 x 1 0-4 1,02 x 1 0-5 2 1 MPa = 1 MN/m 10 6 1 10 10 4 5 1,02 x 10 70 145 1 2 1 bar 10 5 10-1 1 10 3 4 1 2 1,02 x 10 7 1 5 1,02 1 mbar 10 2 0 3 1 mws 9,81 x 10,81 x 10 1 mmws 9,81,81 x 10 2 1 mmhg ( Torr ) 1,33 x 10,33 x 10 3 1 psi 6,89 x 10,89 x 10 2 4 1 kp/cm 9,81 x 10,81 x 10 1-4 10 3 2 2 2 1 kp/cm = 9,6 N/cm = 096 N/mm 2 1 kp = 9,6 kg x m/sec = 9,6 N - 1,02 x 1 0 3 9-9,81 x 1 0-2,81 x 1 0-6 5 9 9,81 x 10-9,81 x 1 0-2 10 3 4 1-1,33 x 1 0-3,33 3 6-6,89 x 1 0-2,89 x 1 0 2 9-9,81 x 1 0-1,81 x 1 0 1-2 2 1,5 x 10 1 7-1,45 x 1 0-2 1,02 x 1 0-3 1 9 1 10 3 1 7,36 x 10 1,42 0-1,36 x 10 1 6,03 x 10-1,5 x 1 0 2 1 -,36 x 1 0 1 7 -,03 x 1 0 1 1 2 7-1,42 x 1 0-3 10-4 1 1 1,93 x 10 2 1-1,36 x 1 0-3 2 1-7 5,17 x 10 1,03 x 10 7 2 2 9 10 1 10 4 2 1 7,36 x 10 1,42 x 10 1 TDS-EU-DIN-F-E-04
PTFE Lined Pipe Spool DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value F x L Select F x L Same construction as select series but only in fix length available: - 0 mm - 0 mm - 10 mm - 0 mm - 0 mm below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Fix or Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 32 1 1 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-PFT-E-4
PTFE Lined Pipe Spool Fabricated Steel Dimensional Data per DN Min L Max L S+ 10% Pipe Weight (ca. kg/m) 2 Flanges Weight (ca. kg) 0 45 2, 5 1, 2 1, 5 85 00 58 3 1, 6 2 90 0 3, 5 2, 5 2, 5 32 95 0 78 3 3, 4 3, 6 0 88 4 5 2 105 0 4 5, 8 5, 5 110 0 122 3 7, 1 6, 6 1 0 138 4 10 8, 3 130 0 8 4 14 9, 9 1 1 0 188 5 17, 5 13, 2 1 1 0 212 7 23, 5 16 175 0 2 6, 39 23 0 195 00 3 8 55, 5 31 210 30 370 8 74 39 3 2 0 430 9 85 52 0 0 00 482 10 67 4 5 0 532 7, 5 130 85 0 260 00 585 6, 5 5 90 0 5 5 4 116 Note: - DN, DN and DN not acc. to DIN 2848 Part Number System 1 ROF 0 10 W XX FF 00XX Type Finished Fitting Pipe Spool 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - - PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined 90 Degree Elbow DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value F x F Select F x L Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Fix or Loose Flanges Special Angle Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 32 1 1 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-L9T-E-04
PTFE Lined 90 Degree Elbow Fabricated Steel Dimensional Data per S ize L S+ 10% Note: DN 3 piece housing DN, and not acc to DIN 2848 Part Number System 1 B90 0 10 W XX FF 00XX Type Finished Fitting 90 Deg. Elbow 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - - PN Weight (ca. kg) 45 3 1, 5 95 58 3, 5 2, 1 110 3,75 2, 7 32 130 78 3,75 4 1 88 6 1 5 5, 9 1 122 75 7, 5 1 138 75 9, 6 5 8 5, 13, 1 1 245 188 5, 5 18, 1 1 285 212 6, 5 30 3 2 8, 5 47 0 4 3 12, 5 76 5 370 1 5 95 3 430 13, 5 142 0 6 482 14 185 4 7 532 14 5 0 830 585 14 985 5 5 578 Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined 45 Degree Elbow DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value F x F Select F x L Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose or Fix Flanges Special Angle Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 32 1 1 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-L5T-E-04
PTFE Lined 45 Degree Elbow Fabricated Steel Dimensional Data per Size Part Number System 1 B45 0 10 W XX FF 00XX Type Finished Fitting L 45 Deg. Elbow 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 S+ 10% Pressure 10 - - PN Weight (ca. kg) 45 45 3, 0 1, 5 58 3, 5 2, 1 70 3, 7 2, 7 32 78 3, 7 0 90 88 3 6 5 5, 9 85 122 7 7, 5 138 7 9, 6 1 8 5, 3 13, 1 1 135 188 5, 5 18, 1 1 1 212 6, 5 26 190 2 8, 5 39 0 2 3 12, 5 62 260 370 1 5 76 3 290 430 13, 5 110 0 3 482 14 141 4 3 532 14 194 0 390 585 14 2 455 5 5 216 Note: DN, and not acc. to DIN 2848 Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Equal Tee DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value F x F x F Select F x L x L below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges on Select Ser. Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders PFA lined 2-pc. construction Standard 32 1 1 0 3 0 4 0 Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-TET-E-04
PTFE Lined Equal Tee Fabricated Steel Dimensional Data per D N L Note: - DN 4 and not acc. to DIN 2848 - DN 0 face to face dimensiones not acc. to DIN 2848 Part Number System 1 TEE 0 10 W XX FF 00XX Type Finished Fitting Equal Tee 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 S+ 10% Pressure 10 - - PN Weight (ca. kg) 45 4 2, 5 95 58 4 3, 2 110 3, 5 5, 5 32 130 78 5 8 1 88 5 9, 5 1 5 11, 5 1 122 5 1 5 1 138 5 19, 5 5 8 6 24 1 245 188 5, 5 34 1 285 212 7 45 3 2 10 72 0 4 3 13 1 5 370 13 210 3 430 6, 5 312 0 6 482 6, 5 375 4 6 532 6, 5 0 0 0 585 6, 5 4 0 5 5 5 Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - 3 x Fixed B - 1 x Fixed 2 x Loose LL - 3 x Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Reducing Tee DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - 1 DN 1 1 DN 2 Value F x F x F Select F x F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Standard St. Special Paint Earthing Studs Vent Extenders Standard PFA-Lined St. Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-TRT-01-E-04
PTFE Lined Reducing Tee Fabricated Steel DN - 1 Dimensional Data per DN 1 DN 2 Part Number System 1 RTE 0 10 W XX FF 00XX Type Finished Fitting Red. Tee L1 Diameter L2 1 Pressure 10 - - PN 2 S 1 + 10% S 2 + 10% Liner W - White E - Anti-Static Resin Type Factory Defined Weight (ca. kg) 95 58 45 0 0 3, 1 110 45 0 0 3, 7 1 88 45 0 0 5, 3 1 110 88 5 3, 5 8 45 0 0 8, 8 1 110 8,9 5 5 1 88 1 5 110 1 1 138 88 5 5 17 3,5 16 1 5 17, 5 110 1 88 21 5 8 6 5 1 22 3,5 19 1 138 5 24 1 1 88 31 5 285 1 212 7 32 3,5 28, 5 1 138 5 34 5 8 6 35, 4 Note: - other dimensiones on request Factory Defined Flanges FF - 3 x Fixed B - 1 x Fixed 2 x Loose LL - 3 x Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Reducing Tee DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - DN 1 DN 2 Value Value not Available in these Sizes Select F x F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 0 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-TRT--E-04
PTFE Lined Reducing Tee Fabricated Steel DN - Dimensional Data per DN 1 DN 2 0 L1 L2 1 2 S 1 + 10% S 2 + 10% Weight (ca. kg) 5 56 5 138 5 59 3 2 10 8 6 63 1 285 212 7 5 83 245 4 3 8 13 6 89 3 2 7 5 118 285 5 370 8 13 6 1 3 2 7 1 Note: - other dimensiones on request Part Number System 1 RTE 0 10 W XX FF 00XX Type Finished Fitting Red. Tee Diameter Factory Defined Pressure 10 - - PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - 3 x Fixed B - 1 x Fixed 2 x Loose LL - 3 x Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Reducing Tee Flange DIN 01; dim. L1 acc to DIN 2848 E, PED at. III (>0) TEFLON by DuPont DN 3 - DN 1 3 0 4 0 DN 2 Value Value not Available in These Sizes Select F x F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Standard 2-pc Body onstruction Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-TRT-3-E-04
PTFE Lined Reducing Tee Fabricated Steel DN 3 - Dimensional Data per DN 1 DN 2 3 0 4 0 L1 L2 1 2 S 1 + 10% S 2 + 10% Weight (ca. kg) 375 170 3 385 176 430 6,5 8 3, 5 187 0 370 6 294 229 3 3 234 6 482 6,5 0 8 5 249 5 370 6, 5 362 302 0 3 308 6 532 6,5 4 8 5 324 6 370 6, 5 437 279 3 4 285 0 585 6,5 8 5 299 575 370 6, 5 412 363 4 3 369 0 5 5 0 8 5 383 6 370 6, 5 496 Part Number System 1 RTE 0 10 W XX FF 00XX Type Finished Fitting Red. Tee 0 0 0 032 0 0 064 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - - PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - 3 x Fixed B - 1 x Fixed 2 x Loose LL - 3 x Loose Note: - other sizes on request 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Equal ross DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value Equal crosses not avaliable in Value Select F x F x F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges on Select Ser. Stainless Steel Housing Heavy Duty Liner onductive Liner Special Paint Earthing Studs Vent Extenders PFA lined 3 pc. body construction Standard 32 1 1 0 3 0 4 0 Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-ET-E-04
PTFE Lined Equal ross Fabricated Steel Dimensional Data per D N L Part Number System 1 KRE 0 10 W XX FF 00XX Type Finished Fitting Equal ross 0 0 0 032 0 0 0 0 S+ 10% Diameter 1 1 0 3 0 4 0 Pressure 10 - - PN Weight (ca. kg) 4 45 2, 5 95 4 58 3, 2 110 3, 5 7, 3 32 130 5 78 1 7 1 5 88 12, 7 1 5, 3 1 5 122 19, 3 1 5 138 26 5 6 8 32 1 245 5, 5 188 45, 3 1 285 7 212 60 3 10 2 96 0 4 13 3 146, 7 5 13 370 213, 3 3 6, 5 430 385 0 6 6, 5 482 485 4 6 6, 5 532 530 0 0 6, 5 585 560 0 5 5 7 Note: - DN 4 and not acc. to DIN 2848 - DN 0 face to face not acc to DIN 2848 Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - 4 x Fixed XX - 1 x Fixed 3 x Loose LL - 4 x Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Reducing ross DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - DN 1 DN 2 Value not available in Value Select F x F x F x F Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Standard Special Paint Earthing Studs Vent Extenders Standard PFA-Lined Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-RT-0-E-04
PTFE Lined Reducing ross Fabricated Steel DN - Dimensional Data per DN 1 DN 2 Note: - other dimensiones on request Part Number System 1 RKR 0 10 W XX FF 00XX Type Finished Fitting Red. ross L1 Diameter Factory Defined L2 1 Pressure 10 - - PN 2 S 1 + 10% S 2 + 10% Liner W - White E - Anti-Static Resin Type Factory Defined Weight (ca. kg) 95 55 45 3, 5 3 3, 5 110 45 3,0 8 0 110 95 55 3, 5 5, 0 45 0 3, 0 8, 3 1 88 110 5 5 11 110 5 3, 5 12 1 1 88 5 5 14 110 1 1 138 88 5,0 5 23 3,5 21 1 5 24 110 5 1 8 6,0 5 30 3,5 1 138 5, 0 32 Flanges FF - 4 x Fixed XX - 1 x Fixed 3 x Loose LL - 4 x Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Reducing ross Flange DIN 01; dim. L1 acc to DIN 2848 E, PED at. III (>0) TEFLON by DuPont DN 1 - DN 1 1 1 0 3 0 4 0 DN 2 1 0 0 0 0 0 0 Value not available in Value Select F x F x F x F Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Standard 3-pc Body onstruction Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-RT-1-E-04
PTFE Lined Reducing ross Fabricated Steel DN 1 - Dimensional Data per DN 1 DN 2 Note: - other sizes on request Part Number System 1 RKR 0 10 W XX FF 00XX Type Finished Fitting Red. ross L1 0 0 0 032 0 0 064 0 Diameter 1 1 0 3 0 4 0 L2 1 Pressure 10 - - PN 2 S 1 + 10% S 2 + 10% Liner W - White E - Anti-Static Resin Type Factory Defined Weight (ca. kg) 1 285 5 212 8 6, 0 5 48 1 3 285 2 212 6, 0 5, 0 91 0 3 0 4 0 1 285 212 5,0 183 4 3 5,2 3 2 6, 0 188 3 2 273 5 370 6,5 6, 5 0 4 3 2 0 2 6 360 430 6,5 5 370 6, 5 375 0 4 3 453 6 482 6,5 6, 5 5 370 461 5 370 5 6 532 6,5 6, 5 0 6 482 5 575 370 5 0 585 6,5 6, 5 0 6 482 535 0 700 585 698 0 5 5 6, 5 0 700 585 7 Flanges FF - 4 x Fixed XX - 1 x Fixed 3 x Loose LL - 4 x Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PFA Lined Instrument Tee DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - DN 1 DN 2 Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-TIT-00-E-04
PFA Lined Instrument Tee Fabricated Steel DN - Dimensional Data per Major size Part Number System 1 MST 0 10 W XX 00 00XX Type Finished Minor Size Fitting Instr. Tee L Diameter H onsult Factory 1 Pressure 10 - - PN 2 S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) 43 1,9 90 60 4 60 2, 2 43 2,4 110 75 4 60 2, 8 43 3,2 60 3, 6 1 92 4 75 75 6, 2 90 92 8, 1 43 3 60 7 135 130 4 75 75 8, 3 90 92 12, 6 Resin Type Factory Defined Flanges 00 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PFA Lined Instrument Tee DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - 0 DN 1 DN 2 Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs 1 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-TIT-0-E-04
PFA Lined Instrument Tee Fabricated Steel DN - 0 Dimensional Data per DN 1 DN 2 1 0 Part Number System 1 MST 0 10 W XX 00 00XX Type Finished Fitting Instr. Tee L Diameter H onsult Factory 1 Pressure 10 - - PN 2 S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) 43 5,5 60 5, 9 1 8 4 75 75 8, 9 90 92 16 75 1 212 75 4 1 7 60 8,2 90 92 21, 8 75 210 2 75 4 17, 8 60 15 90 92 23, 4 75 2 3 75 4 23, 2 60 13,7 90 92, 9 Resin Type Factory Defined Flanges 00 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Instrument Tee flanges acc. to DIN 01, E, PED at. III (>0) TEFLON by DuPont DN - DN 1 DN 2 Value Value Not Available in These Sizes Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 2-Pc Body onstruction 3 0 4 0 Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-TIT--E-04
PTFE Lined Instrument Tee Fabricated Steel DN - Dimensional Data per DN 1 DN 2 3 0 4 0 Part Number System 1 MST 0 10 W XX 00 00XX Type Finished Fitting Instr. Tee L 90 Diameter H onsult Factory 1 Pressure 10 - - PN 2 S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) 110 3 370 88 6,5 / 3 55, 5 1 62, 1 90 110 375 430 88 6,5 / 3 66, 5 43 53,1 1 73, 7 90 110 390 482 88 6,5 / 3 7 5 59,1 1 83, 7 90 110 4 532 88 6,5 / 3 9 5,5 1 93, 7 90 110 4 585 88 6,5 / 3 9 5 72,1 1, 7 90 110 510 5 88 5 / 3 9 5 79,1 1 107, 7 Resin Type Factory Defined Flanges 00 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Equal Lateral Tee E, PED at. III (>0) TEFLON by DuPont DN Value not available in Value Select F x F x F below not available on stock items.option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges on Select Ser. Stainless Steel Housing onductive Liner Special Paint Earthing Studs Vent Extenders 0 032 0 0 0 0 1 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EUR-DIN-LET-E-04
PTFE Lined Equal Lateral Tee Fabricated Steel Dimensional Data per DN L L1 L2 S+ 10% Weight (ca. kg) 290 90 3, 5 5, 2 32 3 90 2 78 5 5, 2 345 245 88 5 8, 1 370 105 2 5 11, 4 0 110 290 122 5 18 430 1 310 138 5 24 470 130 3 8 6 44 1 5 1 3 188 5, 5 53 1 575 1 4 212 7, 9 Part Number System 1 LTE 10 W XX FF 00XX Type Finished Fitting Lateral Tee Diameter 0 032 0 0 0 0 1 1 Pressure 10 - - PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - 3 x Fixed B - 1 x Fixed 2 x Loose LL - 3 x Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Reducing Flange DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - 1 DN 1 DN 2 Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing Eccentric onductive Liner Heavy Duty Liner Special Paint Earthing Studs 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-RFT-01-E-04
PTFE Lined Reducing Flange Fabricated Steel DN - 1 Dimensional Data per Major Size 1 Part Number System 1 RFK 0 10 W XX 00 00XX Type Minor Size Fitting Finished Reducing Flange L Diameter 1 2 Pressure 10 - - PN S+ 10% Liner Type W - White E - Anti-Static Weight (ca. kg) 45 3, 0 2,5 35 58 3, 5 2, 4 58 0 35 88 0 1 58 5,0 B 35 0 9 88 5, 1 0 / 3, 5 A 6, 8 35 138 88 6,6 0 B 6, 4 5 / 3, 5 A 12 88 12 45 8 B 5 / 0 12 138 10 19 5,0 / 0 A 45 212 138 18 8 5,0 / 5 B 17 All major size bolt holes straddle the natural centerline. A - Minor size bolt holes straddle the natural centerline. B - Minor size bolt holes straddle the centerline; Major size bolt holes with thread - Minor size bolt holes are on the natural centerline; Major size bolt holes with thread other dimensiones on request Factory Defined Resin Type Factory Defined Flanges 00 00XX - Standard 0052 - Earthing Stud 0070 - Stainless Steel
PTFE Lined Reducing Flange DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - 3 DN 1 DN 2 Value Value not available in this sizes Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing Eccentric onductive Liner Heavy Duty Liner Special Paint Earthing Studs 0 3 1 1 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-RFT-3-E-04
PTFE Lined Reducing Flange Fabricated Steel DN - 3 Dimensional Data per Major size 0 3 All major size bolt holes straddle the natural centerline. A - Minor size bolt holes straddle the natural centerline. B - Minor size bolt holes straddle the centerline; Major size bolt holes with thread - Minor size bolt holes are on the natural centerline; Major size bolt holes with thread Note: - DN 0 and up have cylindrical openings - other sizes on request Part Number System 1 RFK 0 10 W XX 00 00XX Type Minor Size Fitting Finished Reducing Flange L Diameter 1 2 Pressure 10 - - PN S+ 10% Liner Type W - White E - Anti-Static Weight (ca. kg) 28 5,0 / 0 138 A 27 45 2 8 5,0 / 5 1 212 5, 0 B 23 28 6,0 / 0 8 A 22 45 3 1 212 19 5,0 2 B 16 44 6,0 / 0 8 36 370 A 1 212 6,0 / 0 31 2 5, 5 28 8 47 430 6,0 / 0 A 2 38 Factory Defined Resin Type Factory Defined Flanges 00 Red. Flange 00XX - Standard 0052 - Earthing Stud 0070 - Stainless Steel
PTFE Lined Reducing Flange DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN 0 - DN 1 DN 2 Value Value not available in these sizes Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing Eccentric onductive Liner Heavy Duty Liner Special Paint Earthing Studs 0 4 0 0 0 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-RFT-0-E-04
PTFE Lined Reducing Flange Fabricated Steel DN 0 - Dimensional Data per Major size 0 4 0 Part Number System 1 RFK 0 10 W XX 00 00XX Type Minor Size Fitting Finished Reducing Flange L Diameter 1 2 Pressure 10 - - PN S+ 10% Liner Type W - White E - Anti-Static Weight (ca. kg) 8 6,0 / 0 482 2 A 60 370 6, 0 49 8 532 2 6,0 / 0 A 70 370 58 2 585 370 6,0 / 0 A 77 0 482 62 370 0 5 482 6,0 / 0 A 93 77 86 121 0 585 78 All major size bolt holes straddle the natural centerline. A - Minor size bolt holes straddle the natural centerline. B - Minor size bolt holes straddle the centerline; Major size bolt holes with thread - Minor size bolt holes are on the natural centerline; Major size bolt holes with thread Note: - DN 0 and up have cylindrical openings - DN not acc. to DIN 2848 - other sizes on request Factory Defined Resin Type Factory Defined Flanges 00 00XX - Standard 0052 - Earthing Stud 0070 - Stainless Steel
PTFE Lined oncentric Reducer DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - 1 Major Size Minor Size Value F x F Select F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges on Select Ser. Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-RT-01-E-04
PTFE Lined oncentric Reducer Fabricated Steel DN - 1 Dimensional Data per Major size Part Number System 1 RSK 0 10 W XX FF 00XX Type Finished Minor Size Fitting onc. Reducer L 1 1 2 Diameter Pressure 10 - - PN S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) 45 2,4 1 3,0 58 2, 3 145 88 3, 0 3, 3 1 160 0 / 3, 0 1 1 88 0 8 1 138 6,7 0 / 3,0 185 138 88 6, 3 190 138 0 6, 9 8 12 5 / 3,0 8 88 9, 4 8 9,9 5 / 0 5 8 138 12, 3 212 5,0 / 0 0 212 138 17, 4 212 8 5,0 / 5 18, 3 Note: - other sizes on request Factory Defined Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined oncentric Reducer DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - Major Size Minor Size Value Value not available in this sizes Select F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 1 0 3 0 4 0 1 0 0 3 3 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-RT--E-04
PTFE Lined oncentric Reducer Fabricated Steel DN - Dimensional Data per DN 1 DN 2 0 3 0 4 0 Part Number System 1 RSK 0 10 W XX FF 00XX Type Finished Fitting onc. Reducer L1 Diameter 1 Pressure 10 - - PN 2 S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) 2 8 6,0 / 5 22, 1 270 1 2 212 6,0 / 5, 0, 2 1 305 3 212 6,5 / 5, 0 37, 8 310 3 2 6,5 / 6, 0 4 8 335 370 2 48 6,5 0 3 370 3 52, 6 0 430 3 73,6 4 6,5 430 370 482 370 105 495 6,5 3 482 430 1 3 532 430 148 495 6,5 0 532 482 7 3 585 430 198 6 6,5 0 585 482 210 4 5 532 282 7 5 0 5 585 291 Note: - DN 4 and not acc. to DIN 2848 - other sizes on request Factory Defined Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Eccentric Reducer DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont Major Size Minor Size Value eccentric reducers not available in value series Select F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges on Select Ser. Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 32 1 0 1 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-RET-032-E-04
PTFE Lined Eccentric Reducer Fabricated Steel Dimensional Data per DN 1 D N 2 L 1 1 2 Part Number System 1 RSE 0 10 W XX FF 00XX Type Finished Fitting Ecc. Reducer Diameter Pressure 10 - - PN S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) 32 130 78 3 3 145 88 0 / 3, 0 3, 3 1 0 160 3 1 1 88 3 8 1 138 5,0 / 0 6, 7 185 138 88 3 6, 3 190 138 4 6, 9 8 88 5,5 / 5 9, 4 8 5 / 3 9, 9 5 8 138 5 / 0 12, 3 0 212 138 7 / 6 17, 4 0 212 8 5 / 5 18, 3 270 2 8 6 / 5 22, 1 1 270 2 212 6 / 5, 2 1 305 3 212 6,5 / 5 38 310 3 2 6,5 / 6 45 335 370 2 6, 5 48 Factory Defined Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Solid Spacer DIN 2848 TEFLON by DuPont DN Value Select Option PN 32 1 1 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. DS-EUR-DIN-SFT-E-04
PTFE Solid Spacer Dimensional Data per DN Part Number System 1 DSF 0 10 W XX 00 00XX Type Finished L max Fitting PTFE Solid Spacer d2 0 0 0 032 0 0 0 0 Diameter d4 1 1 0 3 0 4 0 Weight (ca. kg) 14 45 1 16 58 1 22 2 32 31 78 37 88 3 48 4 64 122 5 76 138 6 101 8 75 1 30 1 188 1, 1 1 30 3 212 1, 4 30 1 2 2 0 4 3 3, 2 303 370 4 3 333 430 5 0 382 482 5, 2 4 430 532 6, 1 0 4 585 7, 2 590 5 8, 5 Note: - DN, DN and DN not acc. to DIN 2848 Pressure 10 - - PN Liner W - White Resin Type Factory Defined Flanges 00 - Spacer 00XX - Standard
PTFE Solid Spacer With Support Ring TEFLON by DuPont DN Value Select Option PN 32 1 1 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. DS-EUR-DIN-SXT-E-04
PTFE Solid Spacer With Support Ring Dimensional Data per DN Part Number System 1 DSX 0 10 W XX 00 00XX Type Finished L max Fitting PTFE Solid Spacer With Support Ring d2 0 0 0 032 0 0 0 0 Diameter d4 1 1 0 3 0 4 0 s Pressure 10 - - PN Weight (ca. kg) 14 4 5 2, 3 1 16 57 2, 3 1 22 70 2, 6 2 32 31 76, 1 2, 6 37 88, 9 2, 9 3 48 101, 6 2, 9 4 64 11 3 3, 2 5 76 139, 7 3, 6 6 101 9 4 75 1 30 1 19 7 3 1, 1 1 30 3 212, 5 3 1, 4 30 1 269 3 2 0 4 3 3, 6 3, 2 303 370 4 4 3 333 430 4 5 0 383 482 5 5, 2 4 430 532 5 6, 1 0 4 585 5 7, 2 590 5 5 8, 5 Liner W - White Resin Type Factory Defined Flanges 00 - Spacer 00XX - Standard 0052 - Earthing Stud 0070 - Stainless Steel
PTFE Lined Ring Spacer DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 32 1 1 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-SGT-E-04
PTFE Lined Ring Spacer Fabricated Steel Dimensional Data per DN L min L max S+ 10% d8 Weight (ca. kg/m) 85 2, 5 45 9 3 58 60 1, 2 3 70 1, 8 32 3 78 82 2, 1 105 3 88 92 2, 6 1 3 107 3, 7 1 3 122 127 7 1 3, 5 138 142 6, 3 135 5 8 162 9, 5 1 30 1 5 188 192 11 1 30 145 5 212 218 14 30 175 6, 2 273 18 0 190 6,75 3 328 29 8 370 378 30 3 5 9 430 438 0 2 10 482 488 60 4 2 7, 5 532 5 71 0 60 2 6, 5 585 594 75 60 260 5 5 695 113 Note: - DN, DN and DN not acc. to DIN 2848 Part Number System 1 DSG 0 10 W XX 00 00XX Type Finished Fitting Lined Ring Spacer 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - - PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges 00 - Spacer 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Distance Piece Form H DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value Lined Distance Pieces Not Available in Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 32 1 1 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-SHT-E-04
PTFE Lined Distance Piece Form H Fabricated Steel Dimensional Data per DN Part Number System 1 DSH 0 10 W XX 00 00XX Type Finished L min Fitting Distance Piece Form H L max 0 0 0 032 0 0 0 0 Diameter S+ 10% 1 1 0 3 0 4 0 Pressure 10 - - PN d8 Weight Pipe (ca. kg/m) Liner W - White E - Anti-Static Weight 2 ollars (ca. kg) 90 2, 5 45 1, 2 55 3 58 60 1, 6 45 55 3 70 2, 5 55 32 55 3 78 82 3, 4 7 55 105 3 88 92 5 9 60 1 3 107 5, 8 1, 3 60 1 3 122 127 7, 1 1, 6 70 1 3, 5 138 142 10 2, 3 70 135 5 8 162 14 2, 7 1 70 1 5 188 192 17, 5 4 1 75 145 5 212 218 23, 5 5 175 6, 2 273 39 6, 5 0 90 190 6,75 3 328 55, 5 9 90 8 370 378 74 10 3 90 5 9 430 438 85 14 0 90 2 10 482 488 17 4 230 7, 5 532 5 130 0 2 6, 5 585 594 5 23 1 260 5 5 695 4 32 Note: - DN, DN and DN not acc. to DIN 2848 Resin Type Factory Defined Flanges 00 - Spacer 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Lined Spectacle Blind Flange DIN 2848 / 2874 E, at. III (>0) TEFLON by DuPont Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. DN PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs 32 1 1 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. DS-EUR-ANSI-E90
PTFE Lined Spectacle Blind Flange Fabricated Steel Dimensional Data per Size L S+ 10% k d2 d4 Weight (ca. kg) 18 2, 5 14 45 5 2, 5 75 14 58 55 2, 5 85 14 7 32 2, 5 18 78 1 3 110 18 88 1, 2 4 1 18 1, 4 4 145 18 122 2 30 4 160 18 138 3 30 5 1 18 8 4 1 30 5 210 18 188 5, 5 1 30 5 2 22 212 7, 5 35 5 295 22 2 12 0 6,75 3 22 3 17 6 0 22 370 28 3 6 460 22 430 44 0 6 5 26 482 4 6 5 26 532 77 0 6 6 26 585 6 Notes: 1.) Drawing shows typical Value construction Part Number System 1 BRL 0 10 W XX 00 00XX Type Fitting Diameter Pressure Liner Resin Type Flanges Finished Spectacle Blind Flange 0 0 0 032 0 0 064 0 1 1 0 3 0 4 0 10 - - PN W - White E - Anti-Static Factory Defined 00 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel Form No. DS-EUR-ANSI-E90
PTFE Lined Blind Flange DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs 32 1 1 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-FBT-G-04
PTFE Lined Blind Flange Fabricated Steel Dimensional Data per Size Part Number System 1 BFL 0 10 W XX 00 00XX Type Finished L Fitting Blind Flange S+ 10% 0 0 0 032 0 0 0 0 Diameter Weight (ca. kg) 17 3 8 19 3 9 21 3 1, 2 32 21 3 1, 8 21 3 2, 1 21 3 3 21 3 4 23, 5 3, 5 5 2 5 5 6 1 26, 5 5 9, 1 1 27 5 11, 8 29 5 18 0 31 5 26 31 5 35 3 31 5 45 0 32 6 60 4 32 6 70 0 34 6 85 36 6 1 Note: DN,, 4 and are not acc. to DIN 2848 1 1 0 3 0 4 0 Pressure 10 - - PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges 00 00XX - Standard 0052 - Earthing Stud 0054 - Vent Boss 0070 - Stainless Steel
PTFE Nozzle Liner TEFLON by DuPont DN Value Nozzle Liner Not Available in Value S elect Opt. onductive Liner 32 1 1 0 3 0 4 0 Best Price & Lead Time (1-2 Weeks) Longer Lead Time (4-6 Weeks) Price and Delivery Upon Request TDS-EU-DIN-NLT-E-04
PTFE Nozzle Liner Dimensional Data DN Part Number System 1 NOZ 0 10 W XX 00 00XX Type Finished d Fitting PTFE Nozzle Liner T ol d + Diameter Pressure Liner Resin Type Flanges 0 032 0 0 0 0 S+ 10% 1 1 0 3 0 4 0 d 4+ 10% Weight (ca. kg/m) 21 1, 5 2,75 60 18 32 29 1, 5 3 70 28 35 2 3, 5 88 46 2 4 60 63 2 4 122 84 7 5 2 5 138 1,23 95 2, 5 5 8 1,58 1 118 3 5 188 1,98 1 1 3 5 212 2,12 186 4 6 2 3,76 0 228 5 5, 5 3 24 279 5 6, 7 370 6,32 288 5 7 370 6,82 3 3 6 6, 5 430 7,05 3 344 6 8 430 9,31 0 359 6 6, 5 482 7,92 0 386 6 6 482 7,87 4 8 6 6, 5 5 9,01 0 455 6 12 5 18,45 Note: - Max. length is 1,5m. Longer length on request 10 - DIN W - White Factory Defined 00 - Liner 00XX - Standard
PTFE Lined Dip Pipe E, PED at. III (>0) TEFLON by DuPont DN Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing Use in Vessels with Agitators onductive Liner PTFE Solid Nozzle Special Paint Vacuum Resistance Earthing Studs 32 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EUR-DIN-DPT-E-04
PTFE Lined Dip Pipe Fabricated Steel Dimensional Data per DN 1 Part Number System 1 TAN 10 W XX 00 00XX Typ Finished Outside Dia. x Wall Type Fitting Dip Pipe Diameter L1 + mm Factory Defined L2 + 5 mm Pressure 10 - - PN d3 d4 Liner W - White E - Anti-Static S+ 10% PTFE Type Factory Defined Weight of Pipe (kg/m) 33,7 x 2, 6 I 0 1 39 23 2, 7 2, 6 32 42,4 x 2, 6 I 0 1 49 3 5 78 3, 3 3, 3 0 0 48,3 x 3,2 I 2 1 55 35, 5 48,3 x 5,6 I 3,2 4 88 I 20 1 54 32 2, 7 7, 3 63 x 5 I 00 1 67 45 63 x 8,0 I 3,3 7, 9 I 2700 1 67 38 3, 3 12, 2 76,1 x 0 I 10 1 82, 5 62 122 3, 1 9, 2 0 1 88,9 x 5 I 2 1 96 73 3,4 12, 2 88,9 x 10 I 2 1 96 62 138 3, 4 22, 3 88,9 x 12 I I 1 96 54 3, 4 29 113 x 5,0 I 2 1 12 5 94 5 17, 5 113 x 10 I 2 1 12 5 84 8 5 29, 7 113 x 16,0 I I 1 12 5 72 5 42, 6 1,3 x 6,3 I 1900 1 177, 5 147 1,3 x 8,0 I 5,0 3 8 212 I 1900 1 177, 5 143 5, 0 36, 9 219,1 x 6, 3 I 2 1 230 196 2 5, 3 41, 2 Flanges 00 00XX - Standard 0052 - Earthing Stud 0070 - Stainless Steel
PTFE Lined Sparger E, PED at. III (>0) TEFLON by DuPont DN Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery PN Stainless Steel Housing Use in Vessels with Agitators onductive Liner Special Paint Vacuum Resistance Earthing Studs 32 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EUR-DIN-SPT-E-04
PTFE Lined Sparger Fabricated Steel Dimensional Data per DN Part Number System 1 ELR 10 W XX FN1 0XX Typ Finished Outside Dia. L x Wall Type + mm Fitting PTFE lined Sparger Diameter d3 Pressure 10 - - PN d4 Liner W - White E - Anti-Static S+ 10% Weight Weight of Pipe of Flange (kg/m) (kg) 33,7 x 2, 6 I 0 39 23 2, 7 2, 9 1, 2 32 42,4 x 2, 6 I 0 49 3 5 78 3, 3 3, 6 1, 7 48,3 x 3,2 I 2700 55 35, 5 48,3 x 5,6 I 3,2 4 1, 9 88 I 2900 54 32 2, 7 7, 3 1, 9 63 x 5 I 2 67 45 63 x 8,0 I 3,3 7, 9 2, 5 I 20 67 38 3, 3 12, 2 2, 5 76,1 x 0 I 1900 82, 5 62 122 3, 1 9, 2 3, 0 1 88,9 x 5 I 2 96 73 3,4 12, 2 3, 8 88,9 x 10 I 96 62 138 3, 4 22, 3 3, 8 88,9 x 12 I I 00 96 54 3, 4 29 3, 8 113 x 5,0 I 2 12 5 94 5 17, 5 1 113 x 10 I 2 12 5 84 8 5 29, 7 1 113 x 16,0 I I 12 5 72 5 42, 6 1 1,3 x 6,3 I 0 177, 5 147 1,3 x 8,0 I 5,0 31, 1 6, 6 212 I 0 177, 5 143 5, 0 37, 2 6, 6 219,1 x 6, 3 I 2 230 196 2 5, 3 41, 2 9, 4 0 032 0 0 0 0 1 PTFE Type Factory Defined Flanges FN1 = Type 1 FN2 = Type 2 FN3 = Type 3 00XX - Standard 0052 - Earthing Stud 0070 - Stainless Steel
PTFE Diaphragm TEFLON by DuPont max. Outside Diameter Number of onvolutes 135 3 Value not available in Value S elect Opt. White Liner Black Liner 145 6 1 8 190 8 210 6 6 2 245 13 8 11 8 8 8 260 11 270 8 275 9 295 9 9 330 13 395 13 4 17 4 13 490 16 Standard Best Price & Lead Time (1-2 Weeks) Longer Lead Time (4-6 Weeks) Price and Delivery Upon Request TDS-EU-DIN-DIT-E-04
PTFE Diaphragm Dimensional data max. Outside Dia. +0% / -3% Part Number System 1 MEM 245 08 W 00000000 Typ Finished Fitting PTFE Diaphragm Number of onvolutes max. Outside Diameter 135 145 1 190 210 2 245 260 270 275 295 330 395 4 4 490 d1 + 5% Number of onv. 03 06 08 09 11 13 16 17 d2 + 5% Liner W - White S - Black S + 10% 135 3 52 1, 5 145 6 1, 5 1 8 99 1, 5 190 8 96 38 1, 5 210 6 62 17 1, 8 210 6 75 17 1, 8 2 13 110 14 2, 3 2 8 145 2, 3 2 11 66 2, 3 245 8 96 2, 3 245 8 1 55 2, 3 245 8 143 45 2, 3 260 11 73 2, 5 270 8 132 2, 5 275 9 160 54 2, 5 295 9 160 55 2, 5 9 1 55 2, 5 330 13 7 55 2, 5 395 13 8 54 2, 7 4 17 8 54 3, 3 4 13 2 52 3, 3 490 16 330 3, 3 00000000-Standard
Pressure-temperature-diagramm for 2 convolutions Pressure-temperaturediagramms for PTFE-bellows with standard wall thickness Bellow with 2 convolutions Pressure-temperature-diagramm for 3 convolutions Pressure-temperature-diagramm for 5 convolutions Bellow with 3 convolutions Bellow with 5 convolutions TDS-EU-DIN-G-E-04
Pressure-temperature-diagramm for SHD-bellow with 2 convolutions for non-shock working Pressure-temperaturediagramms for PTFE-bellows with SHD wall thickness Bellow with 2 convolutions Pressure-temperature-diagramm for SHD-bellow with 3 convolutions for non-shock working Pressure-temperaturediagramm for SHD-bellow with 5 convolutions, for non-shock working Bellow with 3 convolutions Bellow with 5 convolutions
DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) vacuum resistance at 10 4 Pa at max. inherent resistance compress. (N / mm) W extension (N / mm) 5 2 10 1 26 24 6 3 10 1 26 24 6 3 10 1 26 24 6 3 19 1 81 63 6 3 30 1 1 90 9 5 45 1 9 9 5 70 1 170 1 13 6 112 1 194 130 1 13 6 166 1 1 230 138 1 13 6 245 1 1 263 145 PTFE-Expansion-Joint 2 onvolutions 13 6 0 0 6 660 10 770 1 2 1 7 45 3,4 1,5 45 6,7 3 7 212 6 8 3 10 1260 0 10 10 4 10 0 Angular deflection approx. 7 max. Axial travel is based on installation without misalignment or angular deflection. The burst pressure is approx. 4 times the max. working pressure shown on the diagramm. The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. For compression : ompression force F c = x S 1/2 where from table S = travel in mm For extension: Expansion force F w = W x S where W from table S = travel in mm 1,5 45 6,7 1,5 45 6,7 3,4 45 7 1 185 260 192 385 3 0 10 8 - - 10 3 8, 7 - - Flanges up to DN 0 have 2 limit bolts, DN 0 and have 3. TDS-EU-DIN-H-E-04
DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) vacuum resistance at 10 4 Pa at max. inherent resistance compress. (N / mm) W extension (N / mm) 10 4 10 1 21 12 5 10 1 21 13 6 10 1 21 13 6 19 1 63 51 9 30 1 81 64 19 9 45 1 124 84 13 70 1 5 13 112 1 175 104 1 14 166 1 1 197 105 1 28 14 245 1 1 2 108 PTFE-Expansion-Joint 3 onvolutes 28 14 0 0 30 14 660 30 770 1 2 1 7 45 3,4 1,5 45 6,7 264 90 190 93 1 95 3 32 18 1260 0 35 10 4 30 0 1,5 45 6,7 1,5 45 6,7 3,4 45 7 237 110 4 0 30 8 3 8, 7 Angular deflection approx. 14 max. Axial travel is based on installation without misalignment or angular deflection. The burst pressure is approx. 4 times the max. working pressure shown on the diagramm. The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. For compression : ompression force F c = x S 1/2 where from table S = travel in mm For extension: Expansion force F w = W x S where W from table S = travel in mm Flanges up to DN 0 have 2 limit bolts, DN 0 and have 3.
DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) inherent resistance compress. (N / mm) W extension (N / mm) 10 8 10 23 12 10 10 23 13 12 10 23 19 12 19 55 12 30 97 43 13 45 56 16 70 114 62 32 16 112 127 67 1 32 16 166 139 1 32 16 245 1 PTFE-Expansion-Joint 5 onvolutes 32 16 0 177 0 32 16 660 1 35 18 770 5 78 3 35 18 1260 210 0 10 67 0 5 alculation of the forces for: ompression of the bellow: force Fc = x S 1/2 with from table S = travel in mm. Extension of the bellow: force Fw = W x S with W from table S = travel in mm. Please notice: - urves and chart are only valid at neutral length and with limit bolts in place. - The max. angular deflection is approx.. - Above mentioned travel, misalignment or angular deflectio are alternatives, i.e. the percentage values are not allowed to exceed % when added together. - Burst pressure is minimum 4x the indicated in the chart. ompared with the pressure curves of the 2- and 3-convolute bellows, it is here much lower because of the risk of buckling. - The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. - For abrasive applications the bellows (on request) can be equipped with a PTFEnozzle liner, flared on one side. Movements are then restricted. Savety instructions: - Follow install. instructions. - Do not exceed pressure / temperature rating shown in the appropriate bellows chart. - Safeguard the units in hazardous service. - Leave limit bolts in. Severe damage can result if they are removed or altered. - Remove the flange covers only when ready to install the bellow - Insure that sealing faces are clean, smooth and parallel. - While installing the flanges, make sure the bolts do not jut out from the flange backside to the bellow. - Improperly installation or beyond the pressure / temperature rating may result in property damage or personal injury. TDS-EU-DIN-I-E-04
DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) inherent resistance compress. (N / mm) W extension (N / mm) 6 2 10 1 141 6 2 10 1 141 6 2, 5 10 1 141 8 3 19 113 9 4 30 260 160 9 5 45 111 144 10 5, 5 70 266 13 6 112 9 188 1 16 7 166 121 132 1 16 8 245 277 234 PTFE-SHD- Expansion Joint 2 convolutes 18 8 0 299 218 0 8 660 174 248 9 770 1 3 22 9 1260 124 377 0 24 10 10 638 563 vacuum data max. temperature ( F) for full vacuum DN - - - 1 1-0 - 0 / F 230 / 4 230 / 4 230 / 4 / 390 175 / 3 For compression forces: ompression force Fc = x S with from table, S = travel in mm. For extension forces: Extension force Fw = W x S with W from table, S = travel in mm. Please notice: - urves and chart are only valid at neutral length and with limit bolts in place. - The max. angular deflection is approx. 5. - Above mentioned travel, misalignment or angular deflection are alternatives, i.e. the percentage values are not allowed to exceed % when added together. - Burst pressure is about 4x the indicated in the chart. - The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. - For abrasive applications the bellows (on request) can be equipped with a PTFEnozzle liner, flared on one side. Movements are then restricted. Savety instructions: - Follow install. instructions. - Do not exceed pressure / temperature rating shown in the appropriate bellows chart. - Safeguard the units in hazardous service. - Leave limit bolts in. Severe damage can result if they areremoved or altered. - Remove the flange covers only when ready to install the bellow - Insure that sealing faces are clean, smooth and parallel. - While installing the flanges, make sure the bolts do not jut out from the flange backside to the bellow. - Improperly installation or beyond the pressure / temperature rating may result in property damage or personal injury.
DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) inherent resistance compress. (N / mm) W extension (N / mm) 9 3 10 1 94 9 4 10 1 94 9 4 10 1 94 13 6 19 133 75 8 30 173 104 9 45 74 96 16 10 70 178 12 112 1 1 1 13 166, 5 88 1 14 245 185 6 PTFE-SHD- Expansion Joint 3 convolutes 28 14 0 145 0 30 14 660 116 1 30 770 167, 3 3 35 1260 129 327 0 35 10 4 375 vacuum data max. temperature ( F) for full vacuum DN - - - 1 1-0 - 0 / F 230 / 4 230 / 4 230 / 4 / 390 175 / 3 For compression forces: ompression force Fc = x S with from table, S = travel in mm. For extension forces: Extension force Fw = W x S with W from table, S = travel in mm. Please notice: - Above shown curves and chart are only valid at neutral length and with limit bolts in place. - The max. angular deflection is approx. 10. - Above mentioned travel, misalignment or angular deflection are alternatives, i.e. the percentage values are not allowed to exceed % when added together. - Burst pressure is about 4x the indicated in the chart. - The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. - For abrasive applications the bellows (on request) can be equipped with a PTFEnozzle liner, flared on one side. Movements are then restricted. Savety instructions: - Follow install. instructions. - Do not exceed pressure / temperature rating shown in the appropriate bellows chart. - Safeguard the units in hazardous service. - Leave limit bolts in. Severe damage can result if they are removed or altered. - Remove the flange covers only when ready to install the bellow - Insure that sealing faces are clean, smooth and parallel. - While installing the flanges, make sure the bolts do not jut out from the flange backside to the bellow. - Improperly installation or beyond the pressure / temperature rating may result in property damage or personal injury. TDS-EU-DIN-J-E-04
DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) inherent resistance compress. (N / mm) W extension (N / mm) 12 5 10 48 38 12 5 10 48 38 12 8 10 48 38 18 8 19 53 30 22 10 30 69 43 22 10 45 30 38 23 14 70 71 29 14 112 56 1 35 14 166 32 35 1 35 14 245 74 62 PTFE-SHD- Expansion Joint 5 convolutes 0 58 0 42 660 46 66 42 16 770 67 3 43 17 1260 101 126 0 45 18 10 170 1 For compression forces: ompression force Fc = x S with from table, S = travel in mm. For extension forces: Extension force Fw = W x S with W from table, S = travel in mm. Please notice: - Above shown curves and chart are only valid at neutral length and with limit bolts in place. - The max. angular deflection is approx.. - Above mentioned travel, misalignment or angular deflection are alternatives, i.e. the percentage values are not allowed to exceed % when added together. - Burst pressure is about 4x the indicated in the chart. ompared with the pressure curves of the 2- and 3-convolute bellows, it is here much lower because of the risk of buckling. - The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. - For abrasive applications the bellows (on request) can be equipped with a PTFEnozzle liner, flared on one side. Movements are then restricted. Savety instructions: - Follow install. instructions. - Do not exceed pressure / temperature rating shown in the appropriate bellows chart. - Safeguard the units in hazardous service. - Leave limit bolts in. Severe damage can result if they are removed or altered. - Remove the flange covers only when ready to install the bellow - Insure that sealing faces are clean, smooth and parallel. - While installing the flanges, make sure the bolts do not jut out from the flange backside to the bellow. - Improperly installation or beyond the pressure / temperature rating may result in property damage or personal injury.
DN 032 0 0 0 axial movement n = 0 lateral movement angular movement torsion eff. bellow crosssection spring rate δ λ α Mt A cδ cλ cα cτ (+ mm) (+ mm) (grd) (knm) ( cm 2 ) (N/mm) (N/mm) (Nm/grd) (knm/grd) axial spring rate lateral spring rate angular torsional stress vacuum service at 72 F 23 5 ( 10 Pa) at 3 F 160 5 ( 10 Pa) 5 2, 3-260 106 1, 3 2 3 9 9, 5 31-130 14 7 1 3 5,5 2, 6 19 1 3 6 272 133 2, 1 3 3 11 1 5 31 1 3 6 136 16 1 1 3 6,5 2, 8 19 1 4 7 276 7 3, 1 5 3 13,5 13 33 2 4 3 195 23 2, 2 4 3 8,5 3 2 67, 1 234 3 4 1, 1 3 16 12 29 3 67, 4 173 34 3 8 3 PTFE-Expansion-Joint with SS Housing & Spacer Bead 0 1 10 3, 2 3 87, 3 2 229 5 1, 6 3 17,5 11 30 4 87, 6 178 53 1 1, 3 3 10 2, 3 16 7 135 3 769 13 5, 6 3 9 28 7 135 183 96 6, 5 2, 8 3 15 3, 9 9 179, 3 290 446 14 6, 9 4 1 5 30 1, 9 1, 7 290 95 14 6, 6 4 1 0 3 0 4 0 3, 9 17 2, 8 26 7 560 912 39 22 4 30, 5 30 2, 8 26 7 2 117 11 4 21 2 19 1 431, 9 412 1123 48 35 5 39 17, 5 30 6, 5 43 1 335 191 31 35 5 22 3 16 6, 5 666 5 3024 95 111 4 6 12, 5 7, 8 667, 4 269 308 49 41 4 6 27 4 17 9, 2 932, 1 4 37 121 108 5 75 47 14 12 932, 1 352 436 89 5 75 30 5 17 11 1119, 2 460 25 139 1 5 75 46 11, 5 23 1119, 2 378 672 1 116 5 75 26 2, 9 13 1448, 8 713 6211 281 333 7 9 52 11, 5 22 1448, 8 357 779 141 167 7 9 35 5 18, 9 548 3643 272 376 7 9 17, 5 24 38 1813, 3 430 645 214 284 7 9 28 2, 8 12 47 2235, 4 955 10492 586 943 1 1 63 1 5 22 47 2235, 4 4 923 261 419 1 1 35 3, 4 12 48 3, 9 548 6482 484 9 1 1 63 11 17 48 3, 9 305 1112 269 511 1 1 Reduction factors for application pressure, temperature related, acc. to flange material 1E1: temperature appl. pressure 1 230 F 212 302 392 4 bar 10 8 7, 5 6, 9 6, 2 psig 142 114 107 98 88 Flange material to select according to service temperature. TDS-EU-DIN-K-E-04
DN 32 axial movement n = 0 lateral movement angular movement torsion eff. bellow crosssection spring rate δ λ α Mt A cδ cλ cα cτ (+ mm) (+ mm) (grd) (knm) ( cm 2 ) (N/mm) (N/mm) (Nm/grd) (knm/grd) axial spring rate lateral spring rate angular torsional stress vacuum service at 72 F 23 5 ( 10 Pa) at 3 F 160 5 ( 10 Pa) 4 2, 1 17 1 19, 7 428 179 2, 2 2 3 7,5 7 24 1 19, 7 238 30 1, 2 1 3 5 2, 5 17 1 3 8 428 187 3, 3 4 3 8,5 9 22 2 3 5 354 34 2, 7 3 3 7,5 3, 9 19 2 4 3 357 141 4 7 3 12 12 3 4 2 390 43 5 6 3 PTFE-Expansion-Joint with SS Housing & Spacer Bead Flanges DIN PN 1 7 2, 7 16 5 67, 2 660 499 12 2, 6 3 13 9 23 5 67, 2 367 83 6, 5 1, 5 3 8 2, 9 16 8 87, 8 7 589 17 6 3 15 9, 5 23 8 87, 8 412 103 9, 6 2, 6 3 15 3, 2 16 1, 3 135, 2 616 700 22 8, 8 3 17,5 10 23 1, 8 135 523 172 19 6, 4 3 10 2, 3 14 1, 9 1, 7 7 1483 35 17 4 17,5 7 1, 9 1, 7 4 277 9, 5 4 1 0 3 0 4 0 13 3, 4 3, 1 26 2 890 14 62 4 23,5 11 21 3, 1 26 2 495 3 35 14 4 2, 5 13 5, 4 436 8 36 64 35 5 26 7, 5 19 5, 4 436 486 634 57 37 35 5 17,5 2, 5 13 11 672 975 08 179 146 4 6 35 8 18 11 672 558 932 84 4 6 2, 8 12 18 932 1188 6676 302 2 5 75 35 8, 5 18 18 932 679 1249 173 1 5 75 21 2, 7 12 22 1116 1190 7596 363 347 5 75 36 8, 5 17 22 1116 6 1414 7 198 5 75 22 2, 7 11 39 1439 1605 11370 635 672 7 9 44 11 18 39 1439 3 1423 318 336 7 9 3, 5 11 53 1830 10 8246 756 7 7 9 45 11, 5 16 53 1830 834 1417 421 417 7 9 24 2, 5 9, 6 66 24 1673 190 10 1248 1 1 48 10 16 66 24 837 2111 5 624 1 1 24 2 8, 1 97 3190 1675 274 1483 2297 1 1 48 8 13 97 3190 838 3161 742 1149 1 1 Reduction factors for application pressure, temperature related, acc. to flange material 1E1: temperature appl. pressure 1 230 F 212 302 392 4 bar 18, 7 17, 2, 5 psig 355 284 2, 5 244 2 Flange material to select according to service temperature.
2 onvoluted PTFE Expansion Joints with Reinforcing Rings DN Value not available in Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of 1.0038 Flanges of 1.4541 onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy 1 1 0 3 0 4 0 Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E2T-SD-E-04
2 onvoluted PTFE Expansion Joints with Reinforcing Rings Dimensional Data DN L + 2% Thread S + 10 % d 1 + 5 % d 3 + 5 % Weight (ca. kg) 35 4 x M12 45 3 24 43 1, 6 35 4 x M12 58 3 24 43 1, 6 35 4 x M12 3 24 43 1, 6 35 4 x M16 88 3 36 57 2, 5 4 x M16 3 75 3, 6 57 4 x M16 122 3 60 91 4 57 8 x M16 138 3, 5 76 104 5, 2 67 8 x M16 8 4 134 6, 9 1 83 8 x M16 188 122 163 11, 2 1 75 8 x M 212 5 1 188 12, 3 8 x M 2 5, 4 0 0 1 12 x M 3 5, 5 3 26 1 12 x M 370 5, 5 2 345 33 3 160 16 x M 430 6 3 438 57 0 178 16 x M24 482 6, 5 390 462 72 4 185 x M24 532 6, 5 4 5 79 0 230 x M24 585 6, 5 470 555 83 160 x M27 5 5 575 6 108 Part Number System 1 K2W 0 10 W P1 SS 00XX Type Finished Fitting Expansion Joint with 2 onvolutes 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste Standard Flanges SS 0017 - Standard 1.0038 0018 - Flanges 1.4541
3 onvoluted PTFE Expansion Joints with Reinforcing Rings DN Value not available in Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of 1.0038 Flanges of 1.4541 onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy 1 1 0 3 0 4 0 Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E3T-SD-E-04
3 onvoluted PTFE Expansion Joints with Reinforcing Rings Dimensional Data DN L + 2% Thread S + 10 % d 1 + 5 % d 3 + 5 % Weight (ca. kg) 45 4 x M12 45 3 24 43 1, 7 45 4 x M12 58 3 24 43 1, 7 46 4 x M12 3 24 43 1, 7 4 x M16 88 3 36 57 2, 6 56 4 x M16 3 75 3, 8 77 4 x M16 122 3 60 91 6 77 8 x M16 138 3, 5 76 104 5, 3 91 8 x M16 8 4 134 7 1 111 8 x M16 188 122 163 11, 4 1 101 8 x M 212 5 1 188 12, 7 137 8 x M 2 5, 4 0 21 0 12 x M 3 5, 5 3 27 196 12 x M 370 5, 5 2 345 35 3 2 16 x M 430 6 3 438 60 0 233 16 x M24 482 6, 5 390 462 75 4 2 x M24 532 6, 5 4 5 91 0 327 x M24 585 6, 5 470 555 110 x M27 5 5 575 6 1 Part Number System 1 K3W 0 10 W P1 SS 00XX Type Finished Fitting Expansion Joint with 3 onvolutes 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste Standard Flanges SS 0017 - Standard 1.0038 0018 - Flanges 1.4541
5 onvoluted PTFE Expansion Joints with Reinforcing Rings DN Value not available in Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of 1.0038 Flanges of 1.4541 onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy 1 1 0 3 0 Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E5T-SD-E-04
5 onvoluted PTFE Expansion Joints with Reinforcing Rings Dimensional Data DN L + 2% Thread S + 10 % d 1 + 5 % d 3 + 5 % Weight (ca. kg) 4 x M12 45 3 24 43 1, 9 4 x M12 58 3 24 43 1, 9 4 x M12 3 24 43 1, 9 4 x M16 88 3 36 57 2, 7 88 4 x M16 3 75 3 117 4 x M16 122 3 60 91 5 117 8 x M16 138 3, 5 76 104 5, 4 139 8 x M16 8 4 134 7, 1 1 167 8 x M16 188 122 163 12 1 3 8 x M 212 5 1 188 1 2 7 8 x M 2 5, 4 0 22 0 12 x M 3 5, 5 3 29 288 12 x M 370 5, 5 2 345 3 3 16 x M 430 6 3 438 0 343 16 x M24 482 6, 5 390 462 81 Part Number System 1 K5W 0 10 W P1 SS 00XX Type Finished Fitting Expansion Joint with 5 onvolutes 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste Standard Flanges SS 0017 - Standard 1.0038 0018 - Flansche 1.4541
2 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings DN Value not available in Value Select Optionen Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of 1.0038 Flanges of 1.4541 onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy 1 1 0 3 0 Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E2T-HD-E-04
2 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings Dimensional Data DN L + 3% Thread DIN 01 S min. S max. d 1 + 5 % d 3 + 5 % Weight (ca. kg) 36 4 x M12 45 2 5 23 41 1, 4 36 4 x M12 58 2 5 23 42 1, 5 36 4 x M12 2, 5 24 43 1, 39 4 x M16 78/88 2, 5 36 57 2,55 47 4 x M16 2, 5 75 3, 7 51 4 x M16 122 2, 5 60 91 5 52 8 x M16 138 2,75 6 76 104 5, 2 64 8 x M16 8 2,75 6 134 6, 9 1 77 8 x M16 188 2,75 6 122 163 11, 3 1 72 8 x M 212 3 6,75 1 188 12, 5 92 8 x M 2 3, 5 6,75 4 0, 5 0 135 12 x M 3 3, 7 5 3 26, 5 135 12 x M 370 4 7, 5 2 345 34 3 1 16 x M 430 5 9 335 435 56 0 6 16 x M24 482 5 10 390 462 74 Part Number System 1 K2W 0 10 W P3 SS 00XX Type Finished Fitting SHD Expansion Joint with 2 onvolutes 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste SHD Flanges SS 0017 - Standard 1.0038 0018 - Flanges 1.4541
3 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings DN Value not available in Value Select Optionen Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of 1.0038 Flanges of 1.4541 onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy 1 1 0 3 0 Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E3T-HD-E-04
3 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings Dimensional Data DN L + 3% Thread DIN 01 S min. S max. d 1 + 5 % d 3 + 5 % Weight (ca. kg) 54 4 x M12 45 2 5 23 41 1, 5 54 4 x M12 58 2 5 23 42 1, 6 54 4 x M12 2, 5 24 43 1, 7 58 4 x M16 78/88 2, 5 36 57 2, 6 69 4 x M16 2, 5 75 3, 8 77 4 x M16 122 2, 5 60 91 6 78 8 x M16 138 2,75 6 76 104 5, 3 96 8 x M16 8 2,75 6 134 7 1 1 8 x M16 188 2,75 6 122 163 11, 4 1 108 8 x M 212 3 6,75 1 188 12, 7 137 8 x M 2 3, 5 6,75 4 0 21 0 195 12 x M 3 3, 7 5 3 27 196 12 x M 370 4 7, 5 2 345 35 3 16 x M 430 5 9 335 435 59 0 233 16 x M24 482 5 10 390 462 75 Part Number System 1 K3W 0 10 W P3 SS 00XX Type Finished Fitting SHD Expansion Joint with 3 onvolutes 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste SHD Flanges SS 0017 - Standard 1.0038 0018 - Flanges 1.4541
5 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings DN Value not available in Value Select Optionen Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of 1.0038 Flanges of 1.4541 onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy 1 1 0 3 0 Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E5T-HD-E-04
5 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings Dimensional Data DN L + 3% Thread S min. S max. DIN 01 d 1 + 5 % d 3 + 5 % Weight (ca. kg) 87 4 x M12 45 2 5 23 41 1, 6 87 4 x M12 58 2 5 23 42 1, 7 87 4 x M12 2, 5 24 43 1, 8 94 4 x M16 78/88 2, 5 36 57 2, 7 112 4 x M16 2, 5 75 4 124 4 x M16 122 2, 5 60 91 8 126 8 x M16 138 2,75 6 76 104 5, 5 5 8 x M16 8 2,75 6 134 7, 2 1 185 8 x M16 188 2,75 6 122 163 11, 8 1 174 8 x M 212 3 6,75 1 188 13, 1 2 8 x M 2 3, 5 6,75 4 0 21, 7 0 3 12 x M 3 3, 7 5 3 27, 8 316 12 x M 370 4 7, 5 2 345 36 3 3 16 x M 430 5 9 335 435 61 0 375 16 x M24 482 5 10 390 462 77 Part Number System 1 K5W 0 10 W P3 SS 00XX Type Finished Fitting SHD Expansion Joint with 5 onvolutes 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste SHD Flanges SS 0017 - Standard 1.0038 0018 - Flanges 1.4541
PTFE-Expansion Joints with SS Housing and Spacer Bead TEFLON by DuPont DN 32-1 DN Value not available in Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of 1.0038 Flanges 1.4541 Bellow of 1.4541 Bellow of Hastelloy 4 onductive Liner PN 32 1 1 Standard Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-EST-321-E-0904
PTFE-Expansion Joints with SS Housing and Spacer Bead DN 32-1 Dimensional Data per DN 032 0 L + 5% - 1,5% S + 10 % + 5 % d 1 + 5 % d 3 + 5 % Weight (ca. kg) 145 3 70 35 61 3, 9 2 3 70 35 61 1 7 4 44 77 5 242 4 44 77 8 0 0 0 179 4 92 56 89 5, 7 294 4 92 56 89 6, 5 181 4 107 72 108 6, 9 287 4 107 72 108 7, 9 185 4 122 84 124 8 275 4 122 84 124 9 1 1 Part Number System 1 EKS 10 W XX LLL1 XX Type Finished 179 5 147 107 1 10 267 5 147 107 1 11 221 5 178 126 181 14 363 5 178 126 181 17 248 5 8 4 212 18 388 5 8 4 212 23 Fitting Stainless Steel Expansion Joint 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - - PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges LL L1 - loose /loose - Length 1 LL L2 - loose /loose - Length 2 26 - Flanges 1.0038 27 - Flanges 1.4541
PTFE-Expansion Joints with SS Housing and Spacer Bead TEFLON by DuPont DN - DN Value not available in Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of 1.0038 Flanges 1.4541 Bellow of 1.4541 Bellow of Hastelloy 4 onductive Liner PN 0 3 0 4 0 Standard Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-EST--E-0904
PTFE-Expansion Joints with SS Housing and Spacer Bead DN - Dimensional Data per DN 0 L + 5% - 1,5% S + 10 % + 5 % d 1 + 5 % d 3 + 5 % Weight (ca. kg) 246 5 8 4 2 418 5 8 4 2 33 241 5 3 8 324 32 390 5 3 8 324 38 3 0 287 6 370 306 376 429 6 370 306 376 51 296 6, 410 337 8 56 7 6, 410 337 8 66 288 6, 4 387 461 74 432 6, 4 387 461 85 4 0 Part Number System 1 EKS 0 10 W XX LLL1 XX Type Finished 329 6, 5 438 516 85 536 6, 5 438 516 113 310 6, 570 489 570 104 510 6, 570 489 570 129 334 5 670 594 678 126 482 5 670 594 678 144 Fitting Stainless Steel Expansion Joint 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - - PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges LL L1 - loose /loose - Length 1 LL L2 - loose /loose - Length 2 26 - Flanges 1.0038 27 - Flanges 1.4541
PTFE-Expansion Joints with SS Housing and Spacer Bead (DIN PN ) TEFLON by DuPont DN 32-1 DN Value not available in Value Select PN Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of 1.0038 Flanges 1.4541 Bellow of 1.4541 Bellow of Hastelloy 4 onductive Liner 32 1 1 Standard Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-EST-PN-321-E-0904
PTFE-Expansion Joints with SS Housing and Spacer Bead (DIN PN ) DN 32-1 Dimensional Data per PN DN 032 0 L + 5% - 1,5% S + 10 % + 5 % d 1 + 5 % d 3 + 5 % Weight (ca. kg) 146 3 70 35 61 4 6 3 70 35 61 2 163 4 44 77 6 263 4 44 77 5, 2 0 0 0 1 4 92 56 89 6 308 4 92 56 89 7, 2 197 4 107 72 108 7, 7 281 4 107 72 108 8, 9 211 4 122 84 124 10 303 4 122 84 124 11 1 1 Part Number System 1 EKS W XX LLL1 XX Type Finished 217 5 147 107 1 13 323 5 147 107 1 16 2 5 178 126 181 19 293 5 178 126 181 21 6 5 8 4 212 23 3 5 8 4 212 28 Fitting Stainless Steel Expansion Joint 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - - PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges LL L1 - loose /loose - Length 1 LL L2 - loose /loose - Length 2 26 - Flanges 1.0038 27 - Flanges 1.4541
PTFE-Expansion Joints with SS Housing and Spacer Bead (DIN PN ) TEFLON by DuPont DN - DN Value not available in Value Select PN Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of 1.0038 Flanges 1.4541 Bellow of 1.4541 Bellow of Hastelloy 4 onductive Liner 0 3 0 4 0 Standard Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-EST-PN--E-0904
PTFE-Expansion Joints with SS Housing and Spacer Bead (DIN PN ) DN - Dimensional Data per PN DN 0 L + 5% - 1,5% S + 10 % + 5 % d 1 + 5 % d 3 + 5 % Weight (ca. kg) 239 5 8 4 2 36 326 5 8 4 2 2 5 3 8 324 51 364 5 3 8 324 57 3 0 293 6 375 306 376 71 1 6 375 306 376 305 6, 410 337 8 103 416 6, 410 337 8 112 328 6, 4 387 461 128 488 6, 4 387 461 146 4 0 Part Number System 1 EKS 0 W XX LLL1 XX Type Finished 377 6, 5 438 516 5 541 6, 5 438 516 179 3 6, 570 489 570 173 8 6, 570 489 570 1 337 5 670 594 678 2 1 5 670 594 678 0 Fitting Stainless Steel Expansion Joint 0 0 0 032 0 0 0 0 Diameter 1 1 0 3 0 4 0 Pressure 10 - - PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges LL L1 - loose /loose - Length 1 LL L2 - loose /loose - Length 2 26 - Flanges 1.0038 27 - Flanges 1.4541