LINED PIPES & FITTINGS

Transcription

1 LINED PIPES & FITTINGS ANSI Standard

2 LINED PIPES & FITTINGS The product The name of the product. Page No. PTFE Lined pipes 16 RL Lined pipes 17 SL Lined pipes 18 Jacketd lined pipes 19 Solid and Lined Spacers 20 Lined Elbow Lined Elbow Llined Elbow Lined Elbow Jacketd lined Elbows 25 Lined Equal Tees 26 Lined Letral Tees 27 Lined Equal Cross 28 Lined Reducing Lined Instrument Tees Lined Manifold 42 Jacketd Tees & Manifold 43 lined concentric reducers 44-45

3 LINED PIPES & FITTINGS Product The name of the product Page No. lined Eccentric reducers lined Reducing Flanges Lined Blind Flanges 53 Nozzle liner 54 Lined dip-pipe 55 Lined Heavy duty Dip-pipe 56 Lined Bended Dip-pipe 57 Lined Sprager 58 Bellow Con 1 59 Bellow Con 2 60 Bellow Con 3 61 Bellow Con 5 62 Lined Sight Glass 63 Tubular Sight Glass 64 Lined Spectacle 65 Lined Spade 66 Lined Swing Check Value 67

4 LINED PIPES & FITTINGS Engiplas A recognized leader in the field of fluoropolymer and thermoplastic liners, offers a unique complete design, manufacturing and installation packages for fluoropolymer lined steel pipe systems and vessels. The combination of relatively expensive, high performance fluoropolymer materials such as PTFE/PFA with an economical high strength carbon steel pipe or vessel structure, results in an overall economical solution to many problems concerning the handling and storage of a wide range of aggressive fluids or ultra-pure liquids. The range of materials used as a liner includes : PTFE (Polytetrafluoroethylene), the oldest fluorocarbon resin, discovered in 1938, with exceptional resistance to practically all chemicals, but requiring an extremely high level of expertise in welding and thermoforming technologies. PFA (Perfluoro-alkoxy), a more recent development having a similar chemical resistance to that of PTFE, but offering improved welding, thermoforming and High purity properties. MFA - is a copolymerization of tetrafluoroethylene and perfluoromethylvinylether. MFA is a new fluoropolymer, with outstanding physical and chemical properties similar to those of other totally fluorinated polymers. It is similar to PFA. FEP (Fluorinated ethylene propylene) resin, with a similar chemical resistance to that of PTFE but with improved welding and forming properties. FEP has lower operating temperatures than PTFE and PFA, but meets the requirements for maximum operating temperatures of both bonded and non-bonded liners. ECTFE is a melt processible fluoropolymer with a 1:1 alternate copolymer structure of Ethylene and Chlorotrifluoroethylene. ECTFE combines superior mechanical toughness with an outstanding chemical inertness. ETFE - Is a related copolymer to ECTFE, consisting of ethylene and tetrafluoroethylene, combines superior mechanical toughness with an outstanding chemical inertness. PVDF Polyvinylidene Fluoride, has excellent mechanical properties and is resistant to most chemicals. Generally offers improved welding and forming properties PP (Polypropylene), offers a reasonable level of chemical and temperature resistance, combined with excellent working properties. PE - (Polyethylene), offers a reasonable level of chemical and temperature resistance, combined with excellent working properties. XLPE (cross linked polyethylene) offers an excellent abrasion resistance and mechanical strength combined with chemical resistance equivalent to polyethylene. With more than 40 years of experience in this field, Engiplas is well known as a leader in the field of welding, thermoforming and lining with the full and ever expanding range of fluoropolymer and high performance thermoplastic materials. Engiplas is in the position to offer not only steel lined pipe systems and structures with common materials, but a wider range from HDPE, XLPE, PVC or C-PVC pipe systems or vessels. No other European company is in a position to offer this unique range of products, nor the capacity to handle projects involving almost all processing equipment such as vessels, Tanks, Heat exchangers, Filter-Housings and pipe systems. We are working with the client to evaluate the performance of the different materials, designing the equipment and the detailed configuration of the pipe system, testing and handing over the finished project. This specification covers materials, manufacturing, testing, inspection and packaging standards for Engiplas's standard and custom made ASME and DIN lined pipe system. 4

5 LINED PIPES & FITTINGS Materials of construction All materials used shall be traceable to origin and records shall be maintained for a minimum of five years. When specified, material and/or test certificates shall be supplied. Lining As standard, Pipe spools shall be lined with PTFE, if requested other materials are available according to Engiplas manual. As standard, Fittings shall be lined with PTFE or PFA, if requested other materials are available according to Engiplas manual. PTFE lining shall be made from resin conforming to the requirements of ASTM D1457 types I, III, IV or VI, ASTM D4894 or ASTM D4895. The PTFE resin shall be virgin material. Reworked material is not permitted. When tested in accordance with the specification, the minimum tensile strength and elongation at break shall be: 20.7 N/mm2 and 250 % for extruded material N/mm2 and 250 % for isostatically moulded material. The SG of the PTFE material shall be in the range 2.15 to 2.19 when tested to ASTM D792 or D1505. PFA PFA lining shall be made from resin conforming to the requirements of Type II materials as defined in ASTM specification D3307. The lining shall be made from virgin resin meeting the requirements of ASTM D3307 or clean reworked resin capable of meeting the requirements of this specification. When tested in accordance with ASTM D3307, the minimum tensile strength shall be 26.2 N/mm2 and the minimum elongation shall be 300 %. FEP FEP lining shall be made from resin conforming to the requirements of materials as defined in ASTM specification D The lining shall be made from virgin resin meeting the requirements of ASTM D or clean reworked resin capable of meeting the requirements of this specification. When tested in accordance with ASTM D638, the minimum tensile strength shall be 20 N/mm2 and the minimum elongation shall be 300 %. ETFE ETFE lining shall be made from resin conforming to the requirements of materials as defined in ASTM specification D3159. The lining shall be made from virgin resin meeting the requirements of ASTM D3159 or clean PTFE reworked resin capable of meeting the requirements of this specification. When tested in accordance with ASTM D638, the minimum tensile strength shall be 47 N/mm2 and the minimum elongation shall be 300 %. PVDF PVDF lining shall be made from resin conforming to the requirements of materials as defined in ASTM specification D3222. The lining shall be made from virgin resin meeting the requirements of ASTM D638 When tested in accordance with ASTM D638, the minimum tensile strength shall be 40 N/mm2 and the minimum elongation shall be 200 %. PP PP lining shall be made from resin conforming to the requirements of materials as defined in ASTM specification D4101. The lining shall be made from virgin resin meeting the requirements of ASTM D4101. When tested in accordance with ASTM D638, the minimum tensile strength shall be 25 N/mm2 and the minimum elongation shall be 300 %. XLPE XLPE lining shall be made from resin conforming to the requirements of materials as defined in ASTM specification D The lining shall be made from virgin resin meeting the requirements of ASTM D When tested in accordance with ASTM D638, the minimum tensile strength shall be 23 N/mm2 and the minimum elongation shall be 300 %. PE PE lining shall be made from resin conforming to the requirements of materials as defined in ASTM specification D The lining shall be made from virgin resin meeting the requirements of ASTM D When tested in accordance with ISO 527, the minimum tensile strength shall be 9 N/mm2. 5

6 LINED PIPES & FITTINGS Pipe Pipe shall be carbon steel to API 5L grade B, ASTM A106 grade B or BS 3601/BS 3602: part 1, EN /2 or equivalent. Flanges and welding-neck collars shall be forged steel to ASTM A105 N Slip on welding collars shall be steel plate to BS A, DIN grades RSt 37-2 or NF A grade E24, EN or equivalent Fittings Fabricated fittings shall be manufactured from the materials stated above. Cast fittings shall be manufactured from the following: Ductile Iron ASTM A395, BS2789 grade 420/12 or DIN 1693 Part 1 GGG40. Cast steel ASTM A216 WCB or equivalent Fabrication standards Qualification of welding procedures, welders and welding operators shall be in accordance with section IX of the ASME Boiler and Pressure Vessel Code or BS 4870 : Part 1 and BS 4871 : Part 1, DIN 8560 or EN All welds shall be visually examined and assessed in accordance with ASME B31.3 or relevant code. Dimensional standards Flanged cast steel fittings shall be in accordance with ASME B16.5 Class 150. Flanged Ductile Iron fittings shall be in accordance with ASME B16.42 Class 150. Fabricated fittings shall be in accordance with the dimensions shown in Engiplas manual. Pipe diameters and wall thicknesses shall be in accordance with the dimension table 1. Flanges for pipe and fittings Flanges for pipe and fittings shall be in accordance with ASME B16.5 Class 150. Flanges shall be slip-on, socket or weld-neck types. Loose backing flanges shall be suitable for use with welding collars. All relevant dimensions and tolerances shall be in accordance with ASME B16.5 Class 150. Threaded bolt holes are not permitted except for reducing flanges. Threaded bolt holes in reducing flanges shall be UNC unless specified otherwise. Welding collars for use with loose backing flanges shall be slip on welding, socket welding or welding neck type. The diameters and thicknesses shall be as given in dimension table 1. Spacers shall be either solid PTFE or lined steel. The outside diameters shall be as given in dimension table 1. The outside diameter of instrument tee bodies shall be the same as lined spacers. The lining on the faces of flanges shall have uniform thickness and shall not be less than 80 per cent of the actual wall thickness. 6

7 LINED PIPES & FITTINGS TABLE 1 Nom Size DT Mm D mm G mm I n X i B mm C mm S mm 1/2" 21,3 88,9 35,1 4X15,7 11, /4" 26,7 98,6 42,9 4X15,7 12, " 33, ,8 4X15,7 14, /4" 42,2 117,3 63,5 4X15,7 15, /2" 48, ,2 4X19,1 17, " 60,5 152,4 91,9 4X19,1 19, /2" 73,2 177,85 104,6 4X19,1 22, " 88,9 190,5 127,0 4X19,1 23, /2" 101,6 215,9 139,7 8X19,1 23, " 114,3 228,6 157,2 8X22,4 23, " 141, ,7 8X22,4 23, " 168,4 279,4 215,9 8X22,4 25, " 219,2 342,9 269,7 8X22,4 28, " 273,1 406,4 323,9 12X25,4 30, " 323,9 482,6 381,0 12X25,4 31, " 355,6 533,4 412,8 12X25,4 35, " 406,4 596,9 469,9 12X28,4 36, " 457, ,4 16X31,8 39, " ,5 584,2 20X31,8 42, " 609,6 812,8 269,2 20X35,1 47,

8 LINED PIPES & FITTINGS Construction Pipe spools Each flanged length shall have two loosed flanges or one fixed welded flange at one end and a welding collar with a loose backing flange at the other. Where vent bosses are not provided, a stop shall be provided on all spool lengths greater than 500mm. The stop is to prevent travel of the loose flange and shall be located within 150mm from the back of the collar. The stop shall be oriented so that it is on the centerline approximately opposite the vent hole. Flanged fittings. Completed fittings shall be one piece construction. Flanges shall be fixed. The preparation and assembly of welded branch connections shall be in accordance with BS 2633 or ASME B31.3, loose flanges are available on request. n Bolt holes. Bolt holes shall be off centers and equally spaced about the centerline to an accuracy of 1.5mm. n Linear and angular dimensions. Linear dimensions +/- 1.5mm Angular dimensions +/ Degrees. Venting Vent holes shall be provided in all pipe spools and shall be 3mm diameter. Pipe lengths up to 500mm shall have one vent PTFE vented plug. Fittings with injection bosses shall be fitted at mid point. Lengths between 500mm and 6000mm shall have two vents, one at each end within approx 100mm of the back of the flange. The vents shall be on the same longitudinal centre line which shall be opposite the flange stops where fitted. Attachment of flanges and collars. The attachment of flanges and collars shall be by both back fillet and bore welds. The transition form the bore to the flanged face shall incorporate a radius to prevent undue stressing of the liner. Fabrication dimensional tolerances. Tolerances for flanges and fittings shall be in accordance with the relevant standards. Fabricated pipework shall be in accordance with the following tolerances: n Straightness of pipes. No deviation of straightness greater than 1/500th of the length. n Squareness of flanges. Square to the axis of the pipe or fitting to within 0.05mm per 25mm measured across the face. n Flange faces. Faces shall not be uneven or concave. Convexity from the bore to the periphery shall not exceed 0.4mm per 25mm width of face. n Flange drilling. PCD +/- 1.5mm. c/c of bolt holes +/- 0.8mm. Eccentricity between PCD and RFD up to 2-1/2 +/- 0.8mm, 3 and greater +/- 1.5mm. 8

9 LINED PIPES & FITTINGS Internal finish of housings The interior surfaces and flange faces shall be clean and free of sharp corners, burrs, rust, scale, weld spatter or other protrusions that could adversely affect the lining. Lining The method of lining and the fit of the lining shall ensure that the lining is capable of withstanding the temperature, pressure and vacuum ratings of the system. All interference fit linings in straight pipes shall be normalized prior to flaring. Completed linings shall show no evidence of pinholes, porosity, cracks or bad workmanship. Sealing surfaces shall be free of surface defects that could impair sealing effectiveness. Scratches, dents, nicks or tool marks on the sealing face shall not be deeper than 0.15mm. Any of these defect types less than 0.15mm but extending across the face shall cause the product to be rejected. Blind flanges shall have linings firmly attached. Production testing PTFE tube tests For each sinter batch, at least one representative sample of each nominal size of tube shall be selected and tests carried out to determine mechanical properties and SG. Where samples do not comply with the requirements stated in this specification, each tube in the batch shall have samples cut from each end and the samples shall be subjected to the same tests. Any sample not meeting the specified requirements shall lead to rejection of the whole tube. The outside diameter and wall thickness shall be measured. Tubes not complying with the standard shall be rejected. Cracks found at the ends of tubes shall be cut off along with at least 50mm of adjacent material. When specified, each liner tube shall be subjected to a flattening test. Each length of tube shall be passed through a pre-set gap between two powered rollers. The gap shall be set at 50 % of the outside diameter of the tube. The tube shall then be rotated about the longitudinal axis through 90 degrees and then passed back through the roller gap. The tube shall be examined for cracks and any cracks along with at least 50mm of adjacent material shall be cut out. PFA Lining tests. Regular production checks shall be carried out to determine mechanical properties and Melt flow rate of the material. Where the results do not comply with the requirements of this specification, the linings shall be rejected. 9

10 LINED PIPES & FITTINGS Hydrostatic pressure test Hydrostatic pressure test is carried out at 16 Bar g water or air. Any evidence of leakage shall be cause for rejection. Electrostatic test Electrostatic testing shall be carried out at a minimum voltage of 20,000 V. The full surface of every lining shall be tested. Any pinholes shall be cause for rejection. Final examination Each item shall be examined visually. Following satisfactory completion, the outside edge of the flange shall be stamped with a letter I to indicate compliance. External finish The outside surface of all pipe and fittings shall be finished as follows. Shot blast SA 2-1/2 and coat with one coat zinc phosphate, epoxy or zinc silicate primer. After painting, bolt holes and vents which become blocked shall be cleared. Marking and identification The following information shall be marked permanently on each pipe and fitting either by casting into the body or by hard stamping the flange edge in letters at least 6mm high: n Manufacturer's sign n Lining material In the case of pipe spools, the length shall be indelibly marked on the pipe body. Packaging All flanges shall be fitted with protective covers. These covers shall only be removed just prior to installation. Straight pipe spools shall be fitted with water resistant medium density fiberboard blanks using a minimum of 4 x M6 bolts. Fittings shall be fitted with medium density fiberboard blanks as above or alternatively, snap on proprietary plastic blanks may be used. Performance All lined pipe and fittings shall be capable of meeting the temperature, pressure, and vacuum ratings stated in Engiplas Lined pipes and fittings manual Service limitations. For positive and negative pressure limitations versus temperature, see tables 2 and 3. Service temperature limits, subject to compatibility with the fluid being handled are; n PTFE & PFA - minus 60 to +200 C n FEP - minus 40 to +170 C n ETFE - minus 20 to +145 C n PVDF - minus 20 to +115 C n XLPE - minus 20 to +85 C n PE & PP - minus 20 to +65 C When Lined tube and fittings are exposed to very low temperatures (less than minus 20 C) consideration must be given as to the suitability of the material used for the housings. See section 5 below for further information Chemical resistance. PTFE,PFA and FEP can be regarded for all intents and purposes as being totally resistant to all chemical solutions except for; molten alkali metals and their solutions Very strong fluorinating agents such as elemental fluorine and chlorine trifluoride. The question of vapor permeation of PTFE can be important with some chemicals under certain operating conditions and this phenomenon should be considered when selecting the lining material. For further information on permeation, as well as on the chemical resistance of other lining materials, please contact our technical services department. 10

11 LINED PIPES & FITTINGS PTFE, PFA and FEP linings are normally non-pigmented, whereas ETFE, PVDF, XLPE and PP may be pigmented, either for material identification or to facilitate a particular production process. Anti static PTFE and PFA are modified versions of the specifications mentioned above, with volume sensitivities less than 106 ohm-cm, and are black in color. TABLE 2 Pressure / temperature rating Pressure Temperature ANSI 150# ANSI 300# PSI BAR PSI BAR 20 C C C C C n Table 2 - valid for series PTFE-PFA up to 200 C / ETFE up to 150 C, PVDF up to 115 C, XLPE up to 85 C and PP & PE up to 70 C. The pressure ratings for ASME 150# and PN16 dimensioned fittings are based on ratings in ASME B n The pressure ratings for ASME 300# dimensioned fittings are based on the rating in ASME B #, down rated to compensate for the decrease in mechanical properties at elevated temperatures of the lining materials. 11

12 LINED PIPES & FITTINGS TABLE 3 Vacuum / temperature rating Liner Temp Diameter PTFE HD PTFE SHD PFA HD PFA Roto FEP ETFE Roto PVDF HD PVDF Roto XLPE Roto PP HD 20 C Full Full Full Full Full Full Full Full Full Full Full 50 C Full Full Full Full Full Full Full Full 100 C Full Full Full Full Full Full 150 C Full Full Full Full Full 200 C Full Full Full Full 20 C Full Full Full Full Full Full Full Full Full Full Full 50 C Full Full Full Full Full Full Full Full Full Full Full 100 C Full Full Full Full Full Full Full Full Full Full Full 150 C Full Full Full Full Full Full Full Full Full Full Full 200 C Full Full Full Full Full Full Full Full Full Full Full 20 C Full Full Full Full Full Full Full Full Full 50 C Full Full Full Full Full Full Full Full Full 100 C Full Full Full Full Full Full 150 C Full Full Full Full Full 200 C Full Full Full Full 20 C Full Full Full Full Full Full Full Full Full Full Full 50 C Full Full Full Full Full Full Full Full Full Full Full 100 C Full Full Full Full Full Full Full Full Full Full Full 150 C Full Full Full Full Full Full Full Full Full Full Full 200 C Full Full Full Full Full Full Full Full Full Full Full 20 C Full Full Full 50 C Full Full Full 100 C Full Full Full 150 C Full Full Full 20 C Full Full Full Full Full Full Full Full Full Full Full 50 C Full Full Full Full Full Full Full Full Full Full Full 100 C Full Full Full Full Full Full Full Full Full Full Full 120 C Full Full Full Full Full Full Full Full Full Full Full 20 C Full Full Full Full Full Full Full Full Full Full Full 50 C Full Full Full Full Full Full 100 C Full Full Full Full Full 20 C Full Full Full Full Full Full Full Full Full Full Full 50 C Full Full Full Full Full Full Full Full Full Full Full 100 C Full Full Full Full Full 20 C Full Full Full Full Full Full Full Full Full Full Full 50 C Full Full Full Full Full Full Full 80 C Full Full Full Full 20 C Full Full Full Full Full Full Full Full Full Full Full 50 C Full Full Full Full Full Full Full Full Full Full Full 80 C Full Full Full Full Full Full Full Please note that sudden changes in pressure (positive and negative), drops frequencies and thermal changes are an influence on the Vacuum resistance of the liner; hence thicker or bonded liner should be considered. 12

13 LINED PIPES & FITTINGS System design and supports. Due to the nature of the dual system of a metallic structure and a thermoplastic inner liner, the potential risk of leakage is situated at flange assemblies, especially if the system is installed without gaskets. The risk of leakage due to difficulties in assembly without gaskets is covered in the following section. Flanges may also leak because of high stress levels imposed on flanges due either to poor installation, lack of supports or non containment of forces and movements due to thermal expansion. Whilst it may not be necessary to run a stress analysis on every system, the designer should make every effort to avoid undue stress and movement due to thermal expansion, either by incorporating directional changes or expansion bellows. Stress analysis of systems working at high temperature is recommended. Pipe systems should be adequately supported in order to avoid excessive deflection of flanged joints, and supports should be installed preferably close to flanges. The requirement for adequate support is critical in areas of high levels of concentration of valves and fittings. Butterfly valves are usually designed for straight metallic or thermoplastic systems, with the diameter of the valve being defined as a function of the inner diameter of the pipe system in question. The inner diameter of lined steel pipe is considerably smaller than the actual steel pipe, and inner diameters of thermoplastic pipes tend to be considerably smaller due to their heavy wall thickness. For these reasons some interference between the inner liner of a lined pipe and the valve vane may be experienced. The designer should consider this possibility early in the selection process for pipe systems and valves, and if required, incorporate adequate conical spacers between the flanges of plastic lined pipe or fittings and the valve. Installation and maintenance instructions for lined pipes & fittings n n n n Lined products must not be welded, brazed or torch cut since this will damage the lining. The material should also be handled with due care and attention, avoiding all mechanical shocks. All flanges are covered to protect them from damage during shipment, storage and handling on site. Should covers be removed for inspection purposes prior to installation, they should be replaced immediately after the inspection of each item is completed. Under normal conditions, covers should only be removed immediately prior to installation. As gaskets are often not required (see below), utmost attention should be made to avoid scratching or otherwise damaging the lining on flange faces. When jointing PTFE/PFA lined pipe and / or fittings together it is generally unnecessary to use gaskets between the sealing faces. On the other hand, when connecting to other materials (steel, thermoplastics, glass fiber reinforced plastic etc) gaskets are mandatory. Gaskets are also required, on both sides, when solid spacers are used. Gaskets may also be used where flange faces are not absolutely parallel or where a gasket will act as a very thin spacer. When pipe work is dismantled and then re-assembled it may be necessary to install gaskets prior to re-assembly. 13

14 LINED PIPES & FITTINGS When joining PVDF or PP lined pipe systems Engiplas recommend that gaskets should be used, although with correct installation it is possible to obtain perfect sealing without them. Torque ratings to achieve sealing of PVDF and PP lined systems without the use of gaskets are relatively high (see below), and lined flange faces may be deformed to the extent that should pipework be dismantled for servicing, the deformation may inhibit subsequent sealing when the pipework is re-assembled. A gasket may be used at this stage in order to obtain sealing, but in the case that several contiguous fittings have been dismantled, the subsequent introduction of gaskets may cause overall dimensional problems. The operator should also pay attention to modify torque ratings for the assembly of joints subsequently using a gasket. Replacement of existing gaskets on an installation which has used gaskets as from the original assembly is, in many cases where PVDF or PP is concerned, a more economic and practical solution. As mentioned above, relatively high torque values are required to obtain sealing without gaskets, but excessive torque can deform the flange face to the extent that a gasket will be required. To avoid this situation as much as possible, the following torque ratings are recommended for jointing lined pipe and fittings for operations at maximum operating temperatures. Note that for pipe systems working at ambient temperature these torque ratings may be increased by 50%, in increments of, should any initial leakage occur. If a flanged connection assembled without a gasket starts to leak even though all the bolts have been tightened to the maximum torque rating, DO NOT CONTINUE TO TIGHTEN THEM ANY MORE. Instead, loosen slightly the bolts opposite the leak, and then tighten up the bolts in the area of the leakage. If leakage persists, the sealing faces of both components should be inspected for groves or chips. Groves or nicks not deeper than approximately 15% of the flare thickness can be removed with a fine grade abrasive paper. Note also that for bolting up joints with a gasket, or when bolting up to vessels or non-lined in line equipment, the operator should respect the torque rating specified for the gasket or for the other equipment or material, as this will generally be significantly lower than the rating required for lined pipe. Installation instructions specific to pipe systems without gaskets. All bolts should be tightened using a torque wrench, gradually tightening opposite bolts ("crisscross") in order to ensure uniform stress, increasing torque by approximately 20% of the required torque in 5 sequential operations, until 80 % of the final bolt torque has been achieved. For tightening to the final torque values, tighten bolts sequently clockwise once around the flange. This will help ensure that the bolts are evenly stressed. All joints should be re-torqued after an initial period of at least 24 hours and/or after an initial thermal cycle which has taken the system to the defined service temperature. The following torque ratings are established for 3 different lining materials, for ASME Class 150 systems, using A193 B7 bolts and A194 2H nuts as a minimum requirement for the determination of minimum mechanical properties. Please contact our technical services for torque ratings to be applied for higher pressure ratings. 14

15 LINED PIPES & FITTINGS TABLE 4 Bolt dimensions and torque ratings for ANSI 150# range Nominal Bore N and diameter of bolts PTFE, PFA, FEP Bolt Torque Ft/ Lb N/m ETFE, PVDF Bolt Torque Ft/ Lb N/m XLPE, PP Bolt Torque Ft/ Lb N/m 25 4 x x x x x x x x x x x Please note that all threads should be clean and lightly lubricated, and that the use of standard washers under both bolt head and nut is strongly recommended. In order to avoid causing damage to the sealing faces, flanges on pipes and fittings working at temperatures above 40 C should only be dismantled once the temperature of the system has been reduced to this temperature level. All PTFE/PFA lined products have small vent holes in the steel housing. It is important that these holes are not blocked by insulation or plugged by paint, as this may cause the lining to collapse. 15

16 PTFE-Lined Pipes 1.1 PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D APL 5 L Gr.B 3 ASTM A 105 SLIP-ON 4 ASTM A 105 LAP-JOINT 5 St DIN PTFE LINING WEIGHT for HD NB L min SD L max HD L max SHD L max LINED PIPE 2 FLANGES mm mm mm mm mm mm mm KG/M KG 1/2" 150 1,5 6, ,000 x x /4" 150 1,5 6, ,000 x x " 150 1,6 6, , , " 150 1,7 6, , , " 150 1,8 6, , , " 200 2,2 6, , , " 200 2,5 6, , , " 200 3,2 6, , , " 200 3,4 6, , , " , , , " , , , " 150 4,0 w 5, , , " 180 4,0 w 5, , , " 180 4,0 w 5, , , " 200 4,0 w 5, , , " 200 4,0 w 5, , , " 250 4,0 w 5, , , " 250 4,0 w 5, , , Standard Version: one fixed flange one loose (lap joint) Part Number: PLPxxx-xxxx - Where XXX are Dia Length (in mm) Available on request: Two fixed or two loosed flanges ANSI B16.5 Class 300 flanges Longer lengths than 6000 mm 16

17 RL lined pipes 1.1 PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D APL 5 L Gr.B 3 ASTM A 105 SLIP-ON 4 ASTM A 105 LAP-JOINT 5 St DIN DN ANSI B Class 150# Lining materials L min PFA ETFE PVDF PP XLPE PE L max PIPE 2 FLANGES mm mm mm mm mm mm mm mm Kg/m Kg 1/2 3/ /4 1 1/ , , / , , , , , , , , , , , , , Standard Version: one fixed flange one loose (lap joint) Part Number: PLPxxx-xxxx - Where XXX are Dia Length (in mm) Available on request: Two fixed or two loosed flanges ANSI B16.5 Class 300 flanges 17

18 SL lined pipes 1.1 PFA ASTM D FEP ASTM D PVDF ASTM D PP ASTM D PE ASTM D APL 5 L Gr.B 3 ASTM A 105 SLIP-ON 4 ASTM A 105 LAP-JOINT 5 St DIN ANSI B Class 150# Lining materials WEIGHT DN L min PFA FEP PVDF PP PE L max PIPE 2 FLANGES mm mm mm mm mm mm mm Kg/m Kg 1/2 x ,500 3/4 x ,500 1 x , /4 x , / , , / , , , , , ,0 w 3,0 w 3,0 w 4,0 w 4,0 w 3, ,0 w 3,0 w 3,0 w 4,0 w 4,0 w 3, ,0 w 3,0 w 3,0 w 4,0 w 4,0 w 3, ,0 w 3,0 w 3,0 w 4,0 w 4,0 w 3, ,0 w 3,0 w 3,0 w 4,0 w 4,0 w 3, ,0 w 3,0 w 3,0 w 4,0 w 4,0 w 3, ,0 w 3,0 w 3,0 w 4,0 w 4,0 w 3, ,0 w 3,0 w 3,0 w 4,0 w 4,0 w 3, Standard Version: one fixed flange one loose (lap joint) Part Number: PLPxxx-xxxx - Where XXX are Dia Length (in mm) Available on request: Two fixed or two loosed flanges ANSI B16.5 Class 300 flanges 18

19 Jacket Lined Pipe 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D St DIN APL 5 L Gr.B 3 ASTM A 105 SLIP-ON 4 ASTM A 105 LAP-JOINT 5 St DIN St DIN APL 5 L Gr.B 7 St DIN St DIN DN L min L max B L1 PTFE PFA ETFE PVDF Part. No Jacket OD Inch mm mm Inch mm mm mm mm mm 1" LSP /2" / LSP " LSP " LSP " LSP " LSP " LSP " LSP Standard Version: One fixed flange one loose (lap joint) Available on request: Loosed flanges ANSI B16.5 Class 300 flanges 19

20 Solid And Lined Spacers 1.1 PTFE Granular white ASTM D PVDF ASTM D PP ASTM D St DIN APL 5 L Gr.B 3 St DIN D D D Form F 5-20 mm Form G mm Form H mm ANSI B Class 150# PTFE PVDF PP DN D Part. No mm mm mm 1/ SPC / SPC SPC / SPC / SPC SPC / SPC SPC SPC SPC SPC SPC SPC SPC SPC SPC SPC SPC SPC Available on request: Different Lengths (L) 20

21 Lined Elbow PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK L S L DN L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No mm mm mm mm mm mm mm mm mm Kg 1/2" X X 3.0 X X X 1.5 ALE /4" X X 3.0 X X X 2.0 ALE " ALE /5" ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " 600 X ALE " 610 X ALE " 673 X ALE " 737 X ALE " 864 X ALE Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 21

22 Lined Elbow PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK 2 L 3 1 S 3 L DN L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No mm mm mm mm mm mm mm mm mm Kg 1/2" X X 3.0 X X X 1.8 ALE /4" X X 3.0 X X X 2.0 ALE " ALE /5" ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " 203 X ALE " 216 X ALE " 241 X ALE Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 22

23 Lined Elbow PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK 3 L 1 2 S L 3 DN L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No mm mm mm mm mm mm mm mm mm Kg 1/2" X X 3.0 X X X 1.6 ALE /4" X X 3.0 X X X 1.8 ALE " ALE /5" ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " 190 X ALE " 203 X ALE " 216 X ALE " 241 X ALE " 279 X ALE Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 23

24 Lined Elbow PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK L 3 2 L 3 1 S DN L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No mm mm mm mm mm mm mm mm mm Kg 1/2" X X 3.0 X X X 1.6 ALE /4" X X 3.0 X X X 1.8 ALE " ALE /5" ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " 190 X ALE " 203 X ALE " 216 X ALE " 241 X ALE " 279 X ALE Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 24

25 Jacket Lined Elbow 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D A A 234 WPB 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK A SAE 5 A 234 WPB L S L DN L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No mm mm mm mm mm mm mm mm mm Kg 1/2" X X 3.0 X X X 1.5 ALE /4" X X 3.0 X X X 2.0 ALE " ALE /5" ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " ALE " 600 X ALE " 610 X ALE " 673 X ALE " 737 X ALE " 864 X ALE Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 25

26 Lined Equal Tee 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No mm mm mm mm mm mm mm mm mm Kg 1/2" 65 x X X X 3.0 ALET /4" 75 x X X X 3.5 ALET " ALET " ALET " ALET " ALET " ALET " ALET " ALET " ALET " ALET " ALET " ALET " * ALET " * ALET " * ALET " * ALET " * ALET Standard Version: Three fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 26

27 Lined Letral Tee 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D XLPE ASTM D PE ASTM D St DIN APL 5 L Gr.B 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK 2 L L1 L DN L L1 PTFE PFA ETFE PVDF XLPE PE Weight Part. No Inch mm mm mm mm mm mm mm mm Kg 1" x LLT /2" LLT " LLT " LLT " LLT " x LLT " x LLT Standard Version: Three fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 27

28 Lined Equal Cross 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No Inch mm mm mm mm mm mm mm mm Kg 1/2" 65 x X X X 3.1 DLC /4" 75 x X X X 4.0 DLC " 89 x DLC " DLC " DLC " DLC " DLC " DLC " DLC " DLC " DLC " * DLC " * DLC " * DLC " * DLC " * DLC " * DLC " * DLC Standard Version: Four fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 28

29 Lined Reducing Tee 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No ** mm mm mm mm mm mm mm mm mm mm Kg 3/4" 1/2" 75 x 3.0 x x x x x 3.0 ALRT " 1/2" x x x x x 3.7 ALRT x 3.0 3/4" x x x x x 3.9 ALRT /2" x x x x x 5.1 ALRT " 3/4" x x x x x 5.3 ALRT " ALRT /2" x x x x x 7.5 ALRT /4" x x x x x 7.7 ALRT " / 3 1" 7.9 ALRT " 9.4 ALRT Standard Version: Three fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 29

30 Lined Reducing Tee 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No ** mm mm mm mm mm mm mm mm mm mm Kg 1" 13.8 ALRT " 1.5" / ALRT " 15.0 ALRT " 19.0 ALRT " 1.5" 19.8 ALRT / 3 2" 21.5 ALRT " 23.5 ALRT " 28.2 ALRT " 6.0 / ALRT " 2" / ALRT " 35.2 ALRT / 4 4" 37.0 ALRT " 6.0 / ALRT " 6.0 / ALRT " 2" 47.0 ALRT " ALRT " 6.0 / / ALRT " 63.0 ALRT Standard Version: Three fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 30

31 Lined Reducing Tee 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No ** mm mm mm mm mm mm mm mm mm mm Kg 10" 12" 1" 1.5" 6.5 / / ALRT " 6.0 / ALRT Standard Version: Three fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 64.6 ALRT " ALRT / / 4 4" 79.3 ALRT " 83.0 ALRT / / " 94.0 ALRT " ALRT " 6.5 / 3 * ALRT " 6.0 / ALRT " 6.5 / 4 * ALRT " 6.5 / ALRT " 4.5 * ALRT " ALRT / 6 * 10" ALRT

32 Lined Reducing Tee 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No ** mm mm mm mm mm mm mm mm mm mm Kg 1" 6.5 / 3 * ALRT " ALRT " ALRT / 3 3" 6.5 / 4 * ALRT " 4" / 4.5 * ALRT " ALRT " 6.5 / 6 * ALRT " ALRT " ALRT " 6.5 / 3 * ALRT " ALRT " ALRT / 3 3" 6.5 / 4 * ALRT / 4" 16" * ALRT " ALRT " 6.5 / 6 * ALRT " ALRT " ALRT " ALRT Standard Version: Three fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 32

33 Lined Reducing Tee 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No ** mm mm mm mm mm mm mm mm mm mm Kg 1" ALRT " 6.5 / 3 * ALRT " 6.0 / ALRT " 6.5 / 4 * ALRT " 6.5 / ALRT " 6" * ALRT " ALRT " ALRT " 6.5 / 6 * ALRT " ALRT " ALRT Standard Version: Three fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 33

34 Lined Reducing Tee 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No ** mm mm mm mm mm mm mm mm mm mm Kg 1" ALRT " 6.5 / 3 * ALRT " 6.0 / ALRT " 6.5 / 4 * ALRT " 6.5 / ALRT " 6" 4.5 * ALRT " ALRT " ALRT " ALRT / 6 * 14" ALRT " ALRT " ALRT Standard Version: Three fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 34

35 Lined Reducing Tee 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No ** mm mm mm mm mm mm mm mm mm mm Kg 1" ALRT " 6.5 / 3 * ALRT " 6.0 / ALRT " 6.5 / 4 * ALRT " 6.5 / ALRT " 6" 4.5 * ALRT " ALRT " ALRT " ALRT " 6.5 / 6 * ALRT " ALRT " ALRT " ALRT Standard Version: Three fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 35

36 Lined Instrument Tees 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D PE ASTM D St DIN GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 2 H S DN 1 L DN 1 DN 2 L H PTFE PFA ETFE PVDF PE PP Weight Part. No ** Inch Inch mm mm mm mm mm mm mm mm Kg 1/2" 2.0 ALIT " 3/4" x ALIT " 2.2 ALIT /2" 2.4 ALIT " 3/4" ALIT X 3.5 1" 2.8 ALIT " ALIT /2" 3.3 ALIT X 3/4" ALIT " 1" / ALIT " ALIT " ALIT /2" 4.3 ALIT X 3/4" ALIT " 1" / ALIT " ALIT » ALIT Standard Version: Fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 36

37 Lined Instrument Tees 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D PE ASTM D St DIN GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 2 H S DN 1 L DN 1 DN 2 L H PTFE PFA ETFE PVDF PE PP Weight Part. No ** Inch Inch mm mm mm mm mm mm mm mm Kg 1/2" 5.5 ALIT X 3/4" ALIT / 3.5 1" ALIT " " ALIT " ALIT / 4.0 3" ALIT /2" 7.7 ALIT X 3/4" ALIT / 3.5 1" ALIT " " ALIT " ALIT / 4.0 3" ALIT /2" 9.9 ALIT X 3/4" ALIT / 3.5 1" ALIT " " ALIT " ALIT / 4.0 3" ALIT Standard Version: Fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 37

38 Lined Instrument Tees 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D PE ASTM D St DIN ASTM A 105 SLIP-ON GGG / A ASTM A 105 WELD-NECK DN 2 H S DN 1 L DN 1 DN 2 L H PTFE PFA ETFE PVDF PE PP Weight Part. No ** Inch Inch mm mm mm mm mm mm mm mm Kg 1/2" 13.1 ALIT X 3/4" ALIT / 3.5 1" ALIT " " ALIT " ALIT / 4.0 3" ALIT /2" 41.5 ALIT X 3/4" ALIT / 3.5 1" ALIT " " ALIT " ALIT / 4.0 3" ALIT /2" 50.7 ALIT X 3/4" ALIT / 3.5 1" 6.5 / 3 * 53.1 ALIT " " ALIT " / 4 * 73.7 ALIT / 4.0 3" ALIT Standard Version: Fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 38

39 Lined Instrument Tees 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D PE ASTM D St DIN GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 2 S H DN 1 L DN 1 DN 2 L H PTFE PFA ETFE PVDF PE PP Weight Part. No ** Inch Inch mm mm mm mm mm mm mm mm Kg 1/2" 57.0 ALIT X 3/4" ALIT / 3.5 1" 6.5 / 3 * 59.0 ALIT " " ALIT " / 4 * 83.0 ALIT / 4.0 3" ALIT /2" 66.0 ALIT X 3/4" ALIT / 3.5 1" 6.5 / 3 * 68.5 ALIT " " ALIT " / 4 * 93.7 ALIT / 4.0 3" ALIT /2" 69.0 ALIT X 3/4" ALIT / 3.5 1" 6.5 / 3 * 72.0 ALIT " " ALIT " / 4 * ALIT / 4.0 3" ALIT Standard Version: Fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 39

40 Lined Instrument Tees 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D PE ASTM D St DIN GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 2 S H DN 1 L DN 1 DN 2 L H PTFE PFA ETFE PVDF PE PP Weight Part. No ** Inch Inch mm mm mm mm mm mm mm mm Kg 1/2" 78.3 ALIT X 3/4" ALIT / 3.5 1" 6.5 / 3 * 79.1 ALIT " " ALIT " / 4 * ALIT / 4.0 3" ALIT Standard Version: Fixed flanges Available on request: Loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 40

41 Lined Concentric Reducer 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No Inch Inch mm mm mm mm mm mm mm mm Kg 3/4" 1/2" x x x x x 2.1 H 1" 1/2" x x x x x x 2.3 ALCR /4" x x x x x x 2.3 ALCR " 3/4" x x x x x x 3.1 ALCR " ALCR " 1" 4.1 ALCR / " 4.8 ALCR " 1" 5.8 ALCR / " 6.9 ALCR " 6.7 ALCR " 1.5" / ALCR " 7.0 ALCR " 10.0 ALCR " ALCR " / 3.5 ALCR " " 14.0 ALCR Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 41

42 Lined Concentric Reducer 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No Inch Inch mm mm mm mm mm mm mm mm Kg 1" 10.5 ALCR " 3" / ALCR " 15.5 ALCR " 8" 10" 12" 14" 1" 4.5 / ALCR " 20.0 ALCR " 5.0 / ALCR " 23.0 ALCR " 22.0 ALCR " 25.3 ALCR " 35.0 ALCR " ALCR " 44.0 ALCR " 45.5 ALCR " ALCR " 52.5 ALCR " 69.0 ALCR " ALCR " 80.0 ALCR Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 42

43 Lined Concentric Reducer 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No Inch Inch mm mm mm mm mm mm mm mm Kg 10" 98.0 ALCR " 12" ALCR " ALCR " ALCR " 14" ALCR " ALCR " ALCR " 14" ALCR " ALCR " ALCR " ALCR " 18" ALCR " ALCR Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 43

44 Lined Eccentric Reducer 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No Inch Inch mm mm mm mm mm mm mm mm Kg 1.5" 1" ALECR " 1" 4.0 ALECR / " 4.3 ALECR " 6.7 ALECR " 1.5" / ALECR " 7.0 ALECR " 11.0 ALECR " 2» / ALECR " 14.8 ALECR " 17.0 ALECR " 3" / ALECR " 21.0 ALECR " 4" 22.0 ALECR " 26.0 ALECR Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 44

45 Lined Eccentric Reducer 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB GGG / A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No Inch Inch mm mm mm mm mm mm mm mm Kg 4" 33.0 ALECR " 6" ALECR " 44.7 ALECR " 45.0 ALECR " 8" ALECR " 53.0 ALECR " 67.5 ALECR " 10" ALECR " 80.0 ALECR " 98.0 ALECR " 12" ALECR " ALECR " ALECR " 14" ALECR " ALECR Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 45

46 Lined Eccentric Reducer 1.1 PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB 3 ASTM A 105 SLIP-ON DN 1 DN 2 L PTFE PFA ETFE PVDF XLPE PE PP Weight Part. No Inch Inch mm mm mm mm mm mm mm mm Kg 20" 12" ALECR " ALECR " ALECR " ALECR " 20" ALECR Standard Version: Two fixed flanges Available on request: One or Two loosed flanges ANSI B16.5 Class 300 flanges Different Lengths (L) 46

47 Lined Manifold 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D Nozzle DN D d1 H T S max Part. No mm mm mm mm mm 1/2" ASDP /4" ASDP " ASDP " ASDP " ASDP " ASDP " ASDP " ASDP " ASDP " ASDP " ASDP " ASDP " ASDP " ASDP " ASDP " ASDP " ASDP

48 Jacketd Tees & Manifold 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D ST37 / A106 / API 5L 48

49 Lined Reducing Flanges 1 PTFE white ASTM D4894/5 2 ASTM A St DIN GGG / A DN2 K2 K1 DN1 DN2 K2 DN1 DN2 K2 DN1 K1 K1 S S S L L L TYPE A TYPE B TYPE C DN 1 DN 2 L PTFE PFA ETFE PVDF PE PP Form Weight Part. No Inch Inch mm mm mm mm mm mm mm Kg 3/4 1/ C 1.7 LCRF /4 1 1/ /2 3 1/2 C 2.1 LCRF /4 C 2.4 LCRF /4 C 3.9 LCRF C 3.5 LCRF / C 4.1 LCRF /4 35 C 4.0 LCRF C 4.1 LCRF /4 3.0 B 5.0 LCRF B 4.9 LCRF /2 C 5.1 LCRF B 5.9 LCRF / C 5.6 LCRF C 5.6 LCRF A 6.8 LCRF / B 6.6 LCRF B 6.4 LCRF Available on request: ANSI B16.5 Class 300 flanges 49

50 Lined Reducing Flanges 1 PTFE white ASTM D4894/5 2 ASTM A St DIN GGG / A DN2 K2 K1 DN1 DN2 K2 DN1 DN2 K2 DN1 K1 K1 S S S L L L TYPE A TYPE B TYPE C DN 1 DN 2 L PTFE PFA ETFE PVDF PE PP Form Weight Part. No Inch Inch mm mm mm mm mm mm mm Kg A 12.0 LCRF /2 4.0 A 12.0 LCRF B 12.0 LCRF C 10.0 LCRF A 16.0 LCRF /2 4 A 15.0 LCRF A 14.0 LCRF B 13.0 LRCF C 13.0 LCRF A 22.0 LCRF /2 4 A 20.0 LCRF A 19.0 LCRF A 18.0 LCRF B 17.0 LCRF A 29.0 LCRF / A 28.5 LCRF A 28.0 LCRF Available on request: ANSI B16.5 Class 300 flanges 50

51 Lined Reducing Flanges 1 PTFE white ASTM D4894/5 2 ASTM A St DIN GGG / A DN2 K2 K1 DN1 DN2 K2 DN1 DN2 K2 DN1 K1 K1 S S S L L L TYPE A TYPE B TYPE C DN 1 DN 2 L PTFE PFA ETFE PVDF PE PP Form Weight Part. No Inch Inch mm mm mm mm mm mm mm Kg 2 A 28.0 LCRF A 24.0 LCRF A 22.0 LCRF A 19.0 LCRF B 16.0 LCRF A 44.0 LCRF A 38.0 LCRF A 36.0 LCRF A 31.0 LCRF A 28.0 LCRF B 24.0 LCRF A 56.0 LCRF A 50.0 LCRF A 47.0 LCRF A 42.0 LCRF A 38.0 LCRF A 35.0 LCRF Available on request: ANSI B16.5 Class 300 flanges 51

52 Lined Reducing Flanges 1 PTFE white ASTM D4894/5 2 ASTM A St DIN GGG / A DN2 K2 K1 DN1 DN2 K2 K1 DN1 DN2 K2 K1 DN1 S S S L L L TYPE A TYPE B TYPE C DN 1 DN 2 L PTFE PFA ETFE PVDF PE PP Form Weight Part. No Inch Inch mm mm mm mm mm mm mm Kg 2 A 56.0 LCRF A 50.0 LCRF A 47.0 LCRF A 42.0 LCRF A 38.0 LCRF A 35.0 LCRF B 33.0 LCRF A 71.0 LCRF A 68.0 LCRF A 62.0 LCRF A 60.0 LCRF A 55.0 LCRF A 49.0 LCRF B 40.0 LCRF A 77.0 LCRF A 72.0 LCRF Available on request: ANSI B16.5 Class 300 flanges 52

53 Lined Blind Flange 1 PTFE white ASTM D4894/5 2 ASTM A St DIN GGG / A S L DN 1 L PTFE Weight Part. No mm Kg 1/ LBF / LBF LBF / LBF / LBF LBF / LBF LBF LBF LBF LBF LBF LBF LBF LBF LBF LBF LBF LBF Available on request: ANSI B16.5 Class 300 flanges 53

54 Nozzel liner 1 PTFE white ASTM D4894/5 C S 1 H D Nozzle DN D C H S max Part. No mm mm mm mm 1.5" ANL " ANL " ANL " ANL " ANL " ANL " ANL " ANL " ANL " ANL " ANL " ANL " ANL " ANL

55 Dippipe Lined 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D PVDF ASTM D PP ASTM D A105 / ST A106 / API 5L 4.0 A105 / ST A105 / ST PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D PVDF ASTM D PP ASTM D ST37 / A106 / API 5L Nozzle DN DN2 Steel pipe L max L1 D d S Part. No mm mm mm mm mm 1" 33.4 * ALDP " * ALDP " * ALDP " * ALDP " 88.9 * ALDP " * ALDP " please * ALDP " indicate in your * ALDP " request * ALDP " * ALDP " * ALDP " * ALDP " * ALDP " * ALDP " 506 * ALDP

56 Dippipe Lined Hd.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D PVDF ASTM D PP ASTM D A105 / ST A106 / API 5L 4.0 A105 / ST A105 / ST PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D PVDF ASTM D PP ASTM D ST37 / A106 / API 5L 9.0 ST37/52 Nozzle DN DN2 Steel pipe L max L1 Part. No D d S mm mm mm mm mm 1" 33.4 * ALDP " * ALDP " * ALDP " please * ALDP " indicate 88.9 * ALDP in your 4" request * ALDP " * ALDP " * ALDP " * ALDP

57 Dippipe Lined Hd 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D PVDF ASTM D PP ASTM D A105 / ST A106 / API 5L 4.0 A105 / ST PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D PVDF ASTM D PP ASTM D ST37 / A106 / API 5L L1 S L A 0 Simple1 C D Nozzle DN DN2 Steel pipe L max L1 D A C S max Part. No mm mm mm deg mm mm 1" 33.4 * ALBDP " * ALBDP " * ALBDP " * ALBDP " please 88.9 * ALBDP " indicate * ALBDP " in your * ALBDP " request * ALBDP " * ALBDP " * ALBDP " * ALBDP " * ALBDP

58 Lined Sprager 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D PVDF ASTM D PP ASTM D A105 / ST A106 / API 5L 4.0 A105 / ST PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D PVDF ASTM D PP ASTM D ST37 / A106 / API 5L 6.0 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D PVDF ASTM D PP ASTM D PTFE Granular white ASTM D PFA ASTM D PVDF ASTM D PP ASTM D4101 L1 L S d4 X X1 D Nozzle DN DN2 Steel pipe L max L1 D X X1 d4 S max min max Part. No mm mm mm mm mm mm mm 1" 33.4 * ALS " * ALS " * ALS " * ALS " 88.9 * ALS " * ALS " please * ALS " indicate in your * ALS " request * ALS " * ALS " * ALS " * ALS " * ALS " * ALS " 506 * ALS

59 Bellows Con 1 1 PTFE white ASTM D4894/5 2 A105 / ST St DIN Coated Steel Bolt 4.0 SS316 Axial movement Lateral movement Angular movement Max pressure bar Max pressure bar Catalog number DN L +/- mm mm Degrees 20 deg c 180 deg c 1" ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL

60 Bellows Con 2 1 PTFE white ASTM D4894/5 2 A105 / ST St DIN Coated Steel Bolt 4.0 SS316 DN L Axial movement Lateral movement Angular movement Max pressure bar Max pressure bar +/- mm mm Degrees 20 deg c 180 deg c Catalog number 1" ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL

61 Bellows Con 3 1 PTFE white ASTM D4894/5 2 A105 / ST St DIN Coated Steel Bolt 4.0 SS316 DN L Axial movement Lateral movement Angular movement Max pressure bar Max pressure bar +/- mm mm Degrees 20 deg c 180 deg c Catalog number 1" ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL

62 Bellows Con 5 1 PTFE white ASTM D4894/5 2 A105 / ST St DIN Coated Steel Bolt 4.0 SS316 DN L Axial movement Lateral movement Angular movement Max pressure bar Max pressure bar +/- mm mm Degrees 20 deg c 180 deg c Catalog number 1" ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL " ABL

63 Lined Sight Glass 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN GGG40/ A216 3 ASTM A 105 SLIP-ON 3.1 ASTM A 105 WELD-NECK 4.0 Tempered Glass / BOROSILICATE 5.0 A105 / ST37 DN A mm B mm S mm Part. No 1" ALS " ALS " ALS " ALS " ALS " ALS " ALS " ALS " ALS " ALS " ALS

64 Lined Tubular Glass 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D A105 / ST Tempered Glass / BOROSILICATE 4.0 Coated Steel Bolt DN L mm S mm C mm D mm Weight Kg Part. No 1" ALSG " ALSG " ALSG " ALSG " ALSG " ALSG " ALSG " ALSG " ALSG " ALSG " ALSG " ALSG " ALSG

65 Lined Spectacle 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN SS304 / SS DN A mm L mm D mm d mm S mm Part. No 1" ALSP " ALSP " ALSP " ALSP " ALSP " ALSP " ALSP " ALSP " ALSP " ALSP " ALSP " ALSP " ALSP " ALSP

66 Lined Spade 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D PVDF ASTM D PP ASTM D XLPE ASTM D PE ASTM D St DIN A 234 WPB 1 2 DN L mm B mm C mm Part. No 1" ATSG " ATSG " ATSG " ATSG " ATSG " ATSG

67 Lined Swing Check Valve 1.1 PTFE Paste white ASTM D4895/D PTFE Granular white ASTM D PFA ASTM D ETFE ASTM D ST37 / ST37/52 DN L mm C mm A mm F mm M mm Open angle Weight Kg Part. No 2" ALSV " ALSV " ALSV " ALSV " ALSV " ALSV " ALSV " ALSV " ALSV

68