MSD DIGITAL INTELLIGENCE SDN.BHD. STANDARD OPERATING PROCEDURE For MIKROTIK ROUTERBOARD RB1100AH (For ADSL) This document has been prepared for the Customer's sole and exclusive information and use and may not be made available to any third parties except with MSD s written consent.
2012 MSD Digital Intelligence Sdn.Bhd., Selangor Company Number:761551-T All rights reserved. No part of this publication maybe reprinted, reproduced, stored in a retrieval system or transmitted, in any formor by any means, without the prior permission in writing from the owners. First published and distributed in Nov,2012.
The device used 1. 1unitPC 2. 1RouterRB1100AH 3. 1unitNetwork(Ethernet)cable 4. PowerCable Discussed in this guide 1. Mikrotik Configuration reset 2. Mikrotik CBC Ext. Configuration 3. ConnectionTest Pre-Configure Laptop 1. Download winbox.exe from Mikrotik(http://download2.mikrotik.com/winbox.exe) 2. Disable wireless interface and firewall.
MikrotikConfigurationreset 1. Plugin network cable from laptop and router port ETH1(any port will do) 2. Run winbox.exe and connect to router using MAC Address 3. Click on New Terminal 4. Type systemreset 5. Type y 6. Exit winbox
Mikrotik Router Configuration Setting IP Addressing Ether 2 Modem 1 Eth 8 Modem 2Eth 9 Modem 3 Eth 10 This configuration only for ADSL line not VSAT Plug in cable at router for ADSL (Take Note) 1. ADSL IP Moderm 1 (192.168.1.1) connect to eth 8 at router mikrotik 1100AH. 2. ADSL IP Moderm 2 (192.168.2.1) connect to eth 9 at router mikrotik 1100AH. 3. ADSL IP Moderm 3 (192.168.3.1) connect to eth 10 at router mikrotik 1100AH
For multiple ADSL, use this bonding script configuration IP > File Drag bonding script to GUI Click restore Router will reboot Open winbox.exe Click symbol to choose with mikrotik want to configure by Mac Address Type admin at login Type m5d1t383 for password Click connect
After that 1. ClickonIP>Addresses 2. Click symbol + a. SetRouterEther2Addressto10.30.4.1/24(IP VLAN 1) (DHCPRange100-200) then set interface as ether 2 and click apply. 10.30.4.1/24 Address Network Interface 10.30.4.1/24 10.30.4.0 Ether2
Example FinalIPaddressingConfiguration look like.
SettingDHCPRange 1. ClickonIP>DHCPServer 2. ClickDHCPSetup Interface DHCPRange Ether2 10.30.4.100 10.30.4.200 Selectinterface 10.30.4.0/24 SetDHCPAddressSpace 10.30.4.1 SetupGatewayforDHCPNetwork
10.30.4.100-10.30.4.200 SetDHCPRangeforeachinterface 8.8.8.8 4.2.2.2 DNSServer8.8.8.8 4.2.2.2 SetLeaseTimeto1hour
DHCP setup done FinalDHCPRangetable
Configure NAT Table VLAN 1 IP > Firewall >NAT General >chain: srcnat >source address: use ip network such as if ipvlan 1-10.16.8.1 so that mean use 10.16.8.0/24. Don t forget to put subnet mask /24 Action >action:masquerade SNMP setting 1. Click on IP>SNMP Felda Bukit Cherakah, Selangor Capping bandwidth setting 1. Click on Queue 2. Click on simple queue then click symbol + 3. Click on general> set queue name>set upload and download limitation>set target (refer to picture below)
Router password setting 1. Click on system>password>old password just ignore it 2. Set a new password-m5d1t383 3. Conform a new password-m5d1t383 ConnectionTest 1. DisablePC/Laptopwireless&firewall 2. ConnectEther2toPC/LaptopwithautomaticIPObtaining. 3. OnPC/Laptopruncommandprompt a. Windows=Start>run>type cmd >hitenter 4. Pinglaptop 5. Repeatstep2to4onall otherethernetportandipaddressconnectedtorouter.