Structural and Dynamic Properties of Concentrated Alkali Halide Solutions: A Molecular Dynamics Simulation Study
|
|
|
- Charleen Blake
- 10 years ago
- Views:
Transcription
1 J. Phys. Chem. B 2007, 111, Structural and Dynamic Properties of Concentrated Alkali Halide Solutions: A Molecular Dynamics Simulation Study Hao Du, Jayendran C. Rasaiah, and Jan D. Miller*, Department of Metallurgical Engineering, 135 South 1460 East, 412 William C. Browning Building, UniVersity of Utah, Salt Lake City, Utah 84112, and Department of Chemistry, UniVersity of Maine, Orono, Maine ReceiVed: July 22, 2006; In Final Form: NoVember 1, 2006 The physicochemical properties of alkali halide solutions have long been attributed to the collective interactions between ions and water molecules in the solution, yet the structure of water in these systems and its effect on the equilibrium and dynamic properties of these systems are not clearly understood. Here, we present a systematic view of water structure in concentrated alkali halide solutions using molecular dynamics simulations. The results of the simulations show that the size of univalent ions in the solution has a significant effect on the dynamics of ions and other transport properties such as the viscosity that are correlated with the structural properties of water in aqueous ionic solution. Small cations (e.g., Li + ) form electrostatically stabilized hydrophilic hydration shells that are different from the hydration shells of large ions (e.g., Cs + ) which behave more like neutral hydrophobic particles, encapsulated by hydrogen-bonded hydration cages. The properties of solutions with different types of ion solvation change in different ways as the ion concentration increases. Examples of this are the diffusion coefficients of the ions and the viscosities of solutions. In this paper we use molecular dynamics (MD) simulations to study the changes in the equilibrium and transport properties of LiCl, RbCl, and CsI solutions at concentrations from 0.22 to 3.97 M. I. Introduction For many years physicochemical properties, such as viscosity, diffusivity, and solubility of brine solutions, have been studied experimentally and theoretically as a function of concentration. The explanation for the dependence of these properties on concentration has been related to the effect of ions on water structure and its dependence on the concentrations of salt solutions. The distinctive feature of water is due to the hydrogen bonding between water molecules, and it is believed that ions of different sizes and charges alter the network structure of water in quite different ways. Previous viscosity measurements, spectroscopic analysis, 1-9 thermodynamic considerations, and flotation tests 15 have revealed that ions of small size (Li + ) interact strongly with water molecules, and form hydrophilic hydration shells, while very large ions behave more nearly like uncharged hydrophobic solutes that interact weakly with surrounding water molecules that form a disordered cage encapsulating the ion. 16,17 X-ray diffraction techniques have shown that the water structure is related to the size of ions in the solution Also, neutron scattering experiments have provided precise information regarding the solvation of water molecules around ions, and illustrate that the water structure is dominated by cation-anion interactions Molecular dynamics (MD) simulation is a fundamental tool that can be used to explore water/water, water/ion, and ionion interactions, and to elucidate the influence of salts on the dynamic properties of brine solutions In the past decade, much research has been devoted to the study of water structure, as well as the dynamic and thermodynamic characteristics of * Addresscorrespondencetothisauthor. [email protected]. University of Utah. University of Maine. electrolyte solutions. 13,17,28,30-41 Also efforts have been made to characterize the energy parameters of various ions. 35,39,42-44 The thermodynamics of solvation of simple ions as a function of their size, charge, and charge inversion have been studied by MD simulation at infinite dilution extensively, 17 and different types of hydration have been identified and discussed in relation to the energy and entropy of solvation. Systematic investigations by MD simulation of concentrated alkali halide solutions with respect to their effect on water structures and the physicochemical properties of the solutions are limited. In this paper we use MD simulations to study how a few of the equilibrium and transport properties of aqueous ionic solutions change as the ion concentration increases. We focus our attention on aqueous ionic solutions of LiCl, RbCl, and CsI at concentrations ranging from 0.22 to 3.97M. The solvation of these ions at room temperature and infinite dilution, where ion-ion interactions are absent, exemplifies the different types of hydration that can occur in solution. 17 The present investigations also reveal how the hydration of these ions is altered as the salt concentration increases, and provide valuable information for further X-ray diffraction and neutron scattering studies. II. Simulation Details For MD simulations we used the DL_POLY_214 program. 45 A simple cubic cell containing 256 particles including water molecules and ions with periodic boundary conditions was used for the simulation. The extended simple point charge (SPC/E) model for water 46 was used. The initial positions of water molecules and ions were distributed randomly in the simulation cell /jp064659o CCC: $ American Chemical Society Published on Web 12/14/2006
2 210 J. Phys. Chem. B, Vol. 111, No. 1, 2007 Du et al. TABLE 1: Potential Parameters for Water/Water, Water/ Ion Interactions ion/water σ io (Å) ɛ io (kj/mol) charge (q) ref Li Rb , 17 Cs Cl I O H , 32, 33 TABLE 2: Average Radii of the First Hydration Shell of Selected Particles distance, Å particle type this study (0.22 M) literature ref O , 32, 33 Li , , 32, 33 + Rb , , 32, 33 Cs , , 32, 42 Cl , , 32 I Figure 1. Hydration number of different anions as a function of The force field adopted in the present study was a combination of the Lennard-Jones and electrostatic interactions expressed as: φ(r ij ) ) 4ɛ ij[( σ 12 r ij) - ( σ r ij) 6] + q i q j (1) r ij where r ij is the distance between particle i and j, σ and ɛ are the size parameter and energy parameter, respectively, and q i is the charge of the ith atom (or ion). The intermolecular potential parameters are derived from the work of Dang et al. and are listed in Table 1. The potential parameters for unlike site pairs are expressed via the Lorentz-Berthelot mixing rules: solution concentration. III. Results and Discussion In this section, the MD simulation results were analyzed in terms of the structural and dynamic properties separately. The results are discussed according to ion sizes and their interactions with water molecules. 1. Structural Properties Water/Ion Interactions. The average radii of the primary hydration shell of selected particles (ion or oxygen atom) determined as the distance to the first minimum in the corresponding pair correlation functions in dilute solutions are listed in Table 2. It is obvious that the size of the hydrated Li + ion represented by the primary hydration shell radius of Å is much smaller than that of water in its coordination shell, which is Å. For larger cations such as Rb + and Cs +, the size of the hydration shell increases accordingly, and is larger than that of the pure water cluster. Similarly, owing to their large size, the Cl - and I - hydration shells are much larger than that of the pure water cluster. The size of the hydrated ions will significantly influence the structure of the system, as well as the dynamic properties of the system such as particle diffusion coefficients and system viscosity, which will be further discussed in later sections The hydration number N h of ions in the primary shell was calculated from the solute-oxygen radial distribution function (RDF) g io (r) using N h ) 4πF* 0 R 1gio (r)r 2 dr (4) σ ij ) σ i + σ j 2 Each simulation was for a constant number of ions and water, constant pressure, and constant temperature (NPT) assembly with the pressure fixed at 0.1 MPa and the temperature fixed at 300 K by using a Hoover s thermostat and barostat. 47 The Ewald sum was used to account for the electrostatic interactions. The Leapfrog method with a time step of 1 fs was used to integrate the particle motion. A total simulation time of 1 ns (10 6 steps of 1 fs) including a 200 ps equilibration period was performed. The final results were analyzed for a further simulation of 800 ps after the equilibration period. (2) ɛ ij ) ɛ i ɛ j (3) where the upper limit corresponds to the first minimum in g io (r) representing the radius for the first hydration sphere, and F* is the density of particles in a given volume. Figure 1 summarizes the hydration numbers for selected cations as a function of salt concentration. As expected, the hydration number is dependent on ion size, and for the same salt concentration increases as the size increases. As the solution becomes more concentrated, the hydration number of cations decreases monotonically with Cs + showing the most significant drop, and Li + the smallest decrease. For small ions such as Li +, the large local electric field binds water molecules in a tetrahedrally coordinated and tightly held hydrophilic hydration shell as shown in Figure 2A. As the solution becomes more concentrated, some of the water molecules participating in the Li + ion hydration shell are replaced by negatively charged Cl - ions as shown in Figure 2B, hence the hydration number of Li + ions decreases as the solution concentration increases. The strong hydrophilic hydration effects of Li + ions also explain the structure of water around the oppositely charged anions as well as in bulk water in the same solution, which will be discussed in later sections. For very large cations such as a Cs + ion, the local electric fields at the ion surface have decreased significantly, and they behave more like uncharged particles. 17 Hence, as the size of the cation increases, the dominating electrostatic hydrophilic hydration of small ions is gradually replaced by hydrophobic hydration of large ions where hydrogenbonded water molecules form a disordered cage surrounding the ions as can be seen in Figure 3A. When hydrophobic hydration dominates, water molecules are loosely bonded to the ion, and the radius of the primary hydration shell is large,
3 Properties of Concentrated Alkali Halide Solutions J. Phys. Chem. B, Vol. 111, No. 1, Figure 2. Snapshot from MDS of 0.9 M LiCl solution containing 4 Li + and4cl - (A) and 3.97 M LiCl solution containing 16 Li + and 16 Cl - (B). Red, oxygen atom in water; yellow, hydrogen atom; purple, Cl - ; and green, Li +. Each Li + is tetrahedrally bonded with four water molecules at low concentration as seen in Figure 1A. When the solution becomes concentrated, some water molecules in the Li + tetrahedral hydration shell are replaced by Cl -, forming direct cation/anion pairing as seen in Figure 1B. Figure 4. Hydration number of different anions as a function of solution concentration. Figure 3. Snapshot from MDS of 0.9 M CsI solution containing 4 Cs + and4i - (A) and 3.97 M CsI solution containing 16 Cs + and 16 I - (B). Red, oxygen atom in water; yellow, hydrogen atom; purple, I - ; and green, Cs +. Water molecules form hydrophobic cages around cations, and stable hydration shells around anions. At high solution concentration, cations and anions pair up minimizing the number of water molecules in the primary hydration shell around ions. allowing more water molecules to be accommodated. As the number of ions increases in the solution, there will be fewer water molecules available to complete the cages around ions, and the cations and anions will pair up to include fewer water molecules in their hydration shells which are fragile and may break, as observed from Figure 3B. Therefore, the hydration number around these ions decreases with concentration and more dramatically for large ions than it does for the small Li + ions. The change of hydration number with salt concentration reveals the balance between the tendency for water molecules to be associated with each other as pure water clusters and the tendency to be associated with ions as hydration shells. For anions, some interesting results have been observed in our simulations. As seen in Figure 4, in LiCl solutions, the hydration number for Cl - was found to increase slightly until the salt concentration increased to 3.97 M. But when the cation is Rb +, the hydration number of Cl - decreases with respect to concentration. This means that the size of the cation has a substantial influence on the structure of water molecules not only around the cation but also around anions when the concentration is high. First of all, due to the asymmetry of the water molecule, the hydration state of anions is different than that of cations with similar size as shown schematically in Figure 5, and is energetically more favorable. Thus, in this arrangement water molecules can accommodate themselves stably around anions. In LiCl solutions, as seen from Figure 2B, it is clear that, as the salt concentration increases, Cl - ions will replace some of the water molecules in the Li + ion tetrahedral hydration Figure 5. Schematic model showing the hydration of Cl -. All the distances shown are obtained from g ClO(r). The orientation of the water molecule directly bonded with the Cl - is due to the asymmetry of water molecules, and thus the hydration of Cl - is energetically more stable than the hydration of similar sized cations. Figure 6. Schematic model showing the replacement of one water molecule in a Li + tetrahedral hydration structure with a Cl -. The three water molecules are within the distance to be included into the primary hydration shell of Cl -. structure. When this happens, as shown schematically in Figure 6, the distance between the Cl - ion and the water molecules in the Li + tetrahedral hydration shell is around 3.66 Å, which is very close to the distance of primary minimum in the Cl-O radial distribution function g OCl (r), and therefore, these water molecules are counted into the hydration shell of the Cl - ion. The more ions in the solution, the greater the possibility for the Cl - and Li + to pair up, leading, therefore, to the larger
4 212 J. Phys. Chem. B, Vol. 111, No. 1, 2007 Du et al. Figure 7. The first shell water/water coordination numbers as a function of solution concentration in different salt solutions. hydration number of the Cl - ions. At very high solution concentration, as many as three Cl - ions can directly bond with one Li + ion as seen in Figure 2B, therefore fewer water molecules are in the Cl - hydration shell, thus, the hydration number decreases. The discrepancy of Cl - ion hydration number at high concentration between neutron scattering experiment ( 5.5) 25 and this study ( 7.2) is due to the fact that in neutron scattering experiments, the hydration number is calculated based on correlation between the Cl - ion and deuterium atoms in D 2 O (g DCl (r)), whereas in this study, the calculation is based on the correlation between the Cl - ion and the oxygen atom in H 2 O (g OCl (r)). From Figure 6, it is clear that when g HCl (r) is used to calculate the Cl - ion hydration number, the distance between the Cl - ion and the hydrogen atoms is larger than the distance of the primary minimum in the g HCl (r), due to the orientation of the water molecules bonded with the Li + ion (water hydrogen atoms pointing away from the Cl - ion). Therefore, these Li + ion bonded water molecules are not counted in the primary Cl - ion hydration shell in the data from neutron scattering experiments. Further, at 3.97 M, the Cl - ion hydration number based on g HCl (r) is about 5.66 in this study, which is in very good agreement with neutron scattering study results. 25 For Rb +, which is a big cation, water molecules form a loose hydration shell as mentioned previously. For the same reason that the hydration number around large cations decreases with solution concentration, the hydration numbers around Cl - ions in RbCl solutions as well as I - ions in CsI solutions become smaller in more concentrated solutions Water/Water Interactions. Water molecules are capable of forming hydrogen bonds, and the number of water molecules directly bonded with a reference water molecule is the primary shell water/water coordination number. The variation of the primary shell water/water coordination number with concentration for different brine solutions is summarized in Figure 7. The variation of water/water coordination is explained in terms of the different hydration structures of ions in the solution. In pure water, water molecules form dynamic tetrahedral networks. When Li + ions are present, some water molecules will be tetrahedrally bonded around Li + ions. As shown schematically in Figure 8, when calculating the coordination number of water 1, besides water 2, 3, and 4, which are directly hydrogen bonded with water 1, water 5, 6, and 7 will also be counted because the distance between water 1 and water 5, 6, and 7, which is around 3.31 Å, is very close to the distance of Figure 8. Schematic model showing the hydration of Li + with distances between particles obtained from the radial distribution functions. It is shown that water 5, 6, and 7 are within the distance to be included into the primary shell of water 1. the primary minimum of pure water from the radial distribution function g OO (r), which is 3.33 Å. Therefore, the coordination number of water 1 is six. As more Li + ions are present, the number of water molecules tetrahedrally bonded with Li + ions increases accordingly, and one direct result is the water/water coordination number increases with salt concentration. Further, at very high solution concentration (3.97 M in this study), the first minimum of the O-O radial distribution function can be as large as 3.7 Å, which is also the theoretically closest distance between water 1 and water molecules that tetrahedrally bonded with water 5, 6, and 7 as is schematically shown in Figure 8. Also, at very high solution concentration, as previously discussed, Cl - can replace water molecules in the Li + ion tetrahedral structure, which leads to the fact that some of the water molecules in the Cl - ion hydration shell are within the distance to be counted as coordinating with water molecules in the Li + ion tetrahedral structure. All these factors contribute to the large water/water coordination number at high solution concentration. In contrast, when large Cs + ions are in the solution, water molecules are loosely caged around these ions. For water molecules composing the cages, because one position has been taken by these large ions, only three other water molecules can be hydrogen bonded to them and counted as primary waters of coordination, thus, the water/water coordination number of these cation bonded water molecules is less than that of the pure water cluster. As more ions are in the solution, more water molecules will be around ions, and consequently, the water/water hydration number decreases monotonically with salt concentrations. In this study, we did not distinguish the water molecules in pure water clusters and those that participate in ion hydration, which play a significant role in terms of the water/water hydration number when the solution concentration is high. For example, in 3.97 M LiCl solution, there are 16 cations, 16 anions, and 224 water molecules. Around each Li + ion, there are about 3.3 tetrahedral bonded water molecules that lead to a total of about 53 water molecules in cation hydration shells. The hydration number of Cl - is 7.33, which includes the contribution of water molecules bonded to the Li + ion that is simultaneously bonded with the Cl -. Taking this factor into consideration, there are only about 4.2 water molecules directly caged around each Cl -, totally about 77 water molecules. That leaves 94 water molecules to participate in pure water clusters. The observed large water/water coordination number of 6 at
5 Properties of Concentrated Alkali Halide Solutions J. Phys. Chem. B, Vol. 111, No. 1, direct cation/anion interaction, which will lead to fewer water molecules participating in the hydration shells (energetically more favorable), the primary coordination number increases faster as a function of salt concentration. For the intermediate ion combination (Rb + and Cl - ), the ion/water and the ion/ion interactions are in close competition Further Water Structure Discussion. The ratio R io, which is expressed as: R io ) no. of water molecules in the secondary shell of particle i no. of water molecules in the primary shell of particle i (5) Figure 9. The first and second shell cation/anion coordination number variation as a function of solution concentration for different salts. this concentration mostly results from the contribution of water molecules around Li + ions. Water molecules in the Cl - hydration shell can also contribute when the Cl - ion is paired up with Li +. As to water molecules in pure clusters, their influence is not very significant if any Cation/Anion Interactions. The cation/anion coordination number as a function of salt concentration is summarized in Figure 9 where both the primary and secondary coordination numbers are presented. Generally speaking, independent of ion species, both the primary and secondary coordination numbers between cation and anion increase when the salt concentration increases. Specifically, for the Li + /Cl - combination, an increase of the secondary coordination number, which is the interaction of hydrated or solvent separated ions, is much more significant than an increase of the primary coordination number, which is the naked ion-ion interaction. In contrast, for the Cs + /I - combination, the primary coordination increases much more significantly with concentration. And for the Rb + /Cl - combination, the change in the coordination number for both the primary and the secondary shell is almost of the same magnitude. When Li + ions are in the solution, due to the strong local electric fields, water molecules are tightly bonded by Li + ions, excluding the direct contact with Cl - ions. When a large number of ions are in the solution, there is competition between ion/water and ion/ ion interactions. Because hydrophilic hydration of Li + ions dominates, driven by minimization of system energy, the coordination number between hydrated ions increases more significantly relative to the direct ion/ion contact. For larger ions such as Cs + ions, loose hydrophobic hydration shells are formed around these ions. On the other hand, water molecules try to keep their integrity as pure water clusters. Because of the where the subscript i represents the reference particle (ion or water molecule) and the subscript O represents the surrounding water. The variations of R io as a function of solution concentration are summarized in Table 3 for cation/water, anion/water, and water/water structures, respectively. In pure water, because all the water molecules are dynamically hydrogen bonded with other water molecules, and form tetrahedral structures, the ratio R OO is around 4.5, the same as the primary shell water/water coordination number. For cation hydration shells, it is noticed that there is almost a monotonic increase of R LiO from about 4.0 in very dilute solution to about 4.4 in concentrated solution. At very low concentration, water molecules tetrahedrally bonded with Li + ions are also tetrahedrally bonded with other water molecules in bulk. Because the radius of the secondary hydration shell of Li + is smaller than the secondary shell for a pure water cluster, fewer water molecules can be accommodated in the secondary hydration shell for Li +, leading to the observed lower R LiO number when compared to pure water clusters. When the solution concentration is increased, some of the water molecules in the primary Li + hydration shell are replaced by Cl - ions as previously discussed, thus, the number of water molecules in the primary hydration shell of a Li + ion is smaller. But some of the water molecules in the Cl - ion primary hydration shell are included in the secondary hydration shell of the Li + ion, therefore, R LiO increases with solution concentration. For larger cations such as Rb + and Cs +, it is obvious that R io is significantly lower than that of pure water clusters at all solution concentrations. As previously discussed, water molecules loosely bond with large cations. These water molecules participating in ion hydration shells are not able to form a complete tetrahedral water cluster with other water molecules. This breakdown of the continuous water network is most significant in the vicinity of the cations, and leads to the observed decrease of R io.as the solutions become more concentrated, Rb + ions and Cs + ions are paired up with corresponding anions in the solutions, and the R io increases with solution concentration as is the case for Li + ions. TABLE 3: Ratio of Water Molecules in the Secondary Shell to Those in the Primary Shell around Ions (R io) as a Function of Solution Concentration ratio of water molecules in the secondary shell to those in the primary shell around ions (R io) concn, M Li + Rb + Cs + Cl - /LiCl Cl - /RbCl I - /CsI LiCl RbCl CsI
6 214 J. Phys. Chem. B, Vol. 111, No. 1, 2007 Du et al. TABLE 4: Residence Times of Various Particles as a Function of Solution Concentration residence time, ps concn, M Cs + Rb + Li + Cl - /LiCl Cl - /RbCl I - /CsI H 2O/LiCl H 2O/RbCl H 2O/CsI For Cl - ions in LiCl solutions, it is interesting to notice that R io instead of increasing as a function of solution, decreases. This is because, in LiCl solution, the Cl - ion can replace water molecules in the primary Li + ion hydration shell. Under this condition, all the other water molecules that bonded with the same Li + ion will be included in the primary hydration shell of this Cl - ion, leading to an increased primary hydration number. On the other hand, due to the large distance between Cl - ion and water molecules in the same primary Li + ion hydration shell, water molecules in the secondary hydration shell of this Li + ion are not within the distance limit to be included in the secondary hydration shell of the Cl - ion. Thus, the R ClO in LiCl solution is significantly lower than that of R OO for pure water clusters, and decreases as a function of solution concentration. For Cl - ions in RbCl solutions and I - ions in CsI solutions, their R io variation follows the same trend as that of cations for the same reasons. One issue that needs to be addressed here is that despite the large sizes of these anions, their ability to break tetrahedral water networks is not as significant as that of large cations, as indicated by their larger R io for the same concentration. This characteristic is explained in terms of the asymmetry of water molecules. Consequently these anions have a greater hydration energy when compared to alkali cations of similar size, and are able to form a more stable hydration shell, 16,17 therefore being less destructive to water structures. R OO describes the structure of water molecules in the bulk. It can be seen that in LiCl solution, R OO decreases monotonically with the solution concentration for the same reason that explains the changes of R ClO in the same solution. In solutions containing larger cations, water molecules in the bulk maintain their tetrahedral network very well as indicated by the large R OO at all concentrations. The noticeable decrease of R OO in RbCl and CsI solutions with solution concentration is due to the fact that some water molecules participate in the formation of hydration shells around large ions in these solutions. In this way the integrity of tetrahedral water structures is lost. Such an analysis also explains the ion/water and cation/anion structures discussed in the previous sections. 2. Dynamic Properties Residence Times. The residence time of water in the primary hydration shells of ions, τ,is defined by τ ) 0 R(t) dt (6) R(t) is derived from time correlation functions 17,40,46 and is defined by R(t) ) 1 N h [θ i (0)θ i (t)] (7) N h i)1 where θ i (t) is the Heaviside unit step function, which has the value 1 if a water molecule i is in the hydration shell of the ion at time t and zero otherwise. N h is the hydration number. Following previous work, 17,40,42,48 the residence time can be accurately approximated by numerical integration of R(t) up to t ) 10 ps with the remainder calculated by fitting R(t) at extended time to an exponential decay e -t/τ. The single time characteristic parameter, τ, would be equal to the actual residence time if the decay of R(t) was exponential at all times. To take account for the temporary excursion of water molecules in the hydration shell, water molecules absent for less than 2 ps are considered as present. Residence times of various particles as a function of solution concentration using the exponential fit method were calculated and are presented in Table 4 for cations, anions, and water molecules. First, the residence time for water molecules in the primary water shell increases inversely with ion size for both cations and anions. Small ions such as Li + strongly interact with water molecules in the hydration shell and therefore significantly confine the movement of water molecules in the primary water shell, resulting in a substantially longer residence time. For large ions such as Cs +,Rb +, and I -, the local electric fields are weak as discussed earlier, and water molecules in the primary hydration shell are more loosely bonded to them. Thus they are more mobile and the residence time of water is shorter. A similar observation has also been documented in the literature. 17,40 Second, the residence time for water in the primary hydration shell around Li + ions increase significantly with solution concentration, while only moderate increase was observed for Rb + ions and almost no noticeable change for Cs + ions. This can also be explained in terms of different hydration shell structures around these ions. Strong hydrophilic hydration is dominating for small ions. At very high solution concentration, as many as one fourth of the total water molecules are tetrahedrally bonded by Li + ions, hence, when one water molecule diffuses away from a Li + ion, there is a very good chance for this water molecule to be tetrahedrally bonded by other Li + ions, therefore the diffusivity of water molecules around Li + ions decreases significantly with solution concentration. This is also the reason for the significantly increased residence times for water molecules around Cl - ions and within pure water clusters in LiCl solution as a function of solution concentration. When the ion size increases, hydrophobic hydration plays a more significant role and water molecules form cages and bond loosely around ions. Under this condition, the diffusivity of water molecules in pure water clusters and around ions is of the same magnitude. In very concentrated solutions, despite the fact that almost all water molecules participate in the hydration of ions, the mobility of water molecules does not change significantly. Therefore, in CsI solution, the residence time of water does not have a noticeable change with solution concentration. Only a marginal increase was noticed for water molecules in RbCl solutions.
7 Properties of Concentrated Alkali Halide Solutions J. Phys. Chem. B, Vol. 111, No. 1, TABLE 5: Comparison of Calculated Diffusion Coefficients at 0.22 M with Values Reported in the Literatures at Infinite Dilution ion or diffusion coefficient, 10-9 m 2 s -1 molecule this study literature ref Li Rb Cs , 30, 40 Cl I H 2O Self-Diffusion Coefficients. The tracer diffusion coefficient D i of an ion can be calculated from its mean square displacement (MSD) 17,40,49 by using the relationship 1 D i ) lim tf 6 [r i (t) - r i (0)]2 (8) where r i (t) is the position of a particle i at time t. The diffusion coefficients of ions in dilute solution (0.22 M in this study) are summarized in Table 5, and compared with literature values at infinite dilution. The diffusion coefficients of ions calculated in the current study are close to the values from the literature, demonstrating that the simulation has been validated. The observed differences in the diffusion coefficients can be explained in terms of the solution concentration in the simulation, which is 0.22 M for the current study and is the infinite dilute state for the references. The diffusion coefficients for cations, anions, and water are shown as a function of salt concentration in Table 6. From the table, it can be seen that the diffusion coefficients for the ions and water molecules decrease with increasing salt concentration. Close analysis of these data indicates that the decrease in diffusion coefficients with concentration is the smallest for the CsI solution and largest for LiCl solution. In both cases, as the concentration increases, the diffusion coefficients of the cation and anion become more nearly alike. A similar observation has been made in previous studies of aqueous solutions of NaCl and KCl solutions at high concentrations. 40,50 As for the systems containing large ions (Cs +,Rb +, and I - ) with weaker electric fields, the observed decrease of ion diffusivity can be explained also in terms of increased ion pairing, which slows down the movement of ions and water molecules bound to them. The self-diffusion of water molecules in LiCl solution changes dramatically in magnitude as the solution becomes denser. The self-diffusion coefficient of SPC/E water at 25 Cis m 2 s -1 and decreases by 40% as the concentration of the LiCl solution increases from 0.22 M to 3.97 M (see Table 6). Over the same concentration range, the diffusion coefficient of water in RbCl and CsI shows a slight increase (more apparent in CsI solutions) and finally an overall drop by 33% and 6% respectively at 3.97 M from their values 0.22 M. The decrease in the diffusion coefficient of water with concentration of LiCl can be attributed to fewer unbound water molecules outside the tightly bound hydration sheaths of Li + ions and LiCl ion pairs. The initial increase in the diffusion coefficient of water as the salt concentration of RbCl and CsI increases is interesting and may be attributed to the increase in number of water molecules in the more loosely bound hydration cages of these ions. As the concentration increases further increased ion pairing slows down the movement of the ions and water molecules bound to them as discussed above. In CsI solutions, water molecules exist either in ion hydration shells or in pure water clusters; nevertheless, the mobility of water molecules in these two phases does not have a significant difference as discussed previously, therefore the diffusivity of water molecules is relatively independent of the solution concentration Viscosity. The shear viscosity η, which describes resistance to flow, can be calculated by using equilibrium fluctuation of the off-diagonal components of the stress tensor. 51 Averaging over the three off-diagonal components can improve the statistical convergence of the calculation. It was shown by Daivis and Evans 29,51 that, for an isotropic system, the statistical convergence can be further improved by including equilibrium fluctuations of the diagonal components of the stress tensor. The generalized Green-Kubo formula therefore can be expressed as: where V and T are volume and temperature of the simulation cell, k B is the Boltzmann constant, q Rβ is a weight factor (q Rβ ) 1ifR*β, q Rβ ) 4 / 3 if R)β ), and P Rβ is defined as where δ Rβ is the Kronecker delta (δ Rβ ) 1ifR)β, δ Rβ ) 0 if R*β ). By analogy with the Einstein relationship for self-diffusion, the shear viscosity can be calculated by using the mean-square displacement of the time integral of the shear components of the stress tensor: 52 where η ) V 0 10k B T V η ) lim tf 20k B Tt R β q Rβ P Rβ (t)p Rβ (0) dt (9) δ Rβ P Rβ ) (σ Rβ + σ βa )/2-3 ( σ γγ ) (10) γ R β q Rβ [L Rβ (t) - L Rβ (0)] 2 ) V lim tf 20k B Tt R β q Rβ [ L Rβ (t)] 2 (11) TABLE 6: Diffusion Coefficients for Cations, Anions, and Water Shown as a Function of Salt Concentration diffusion coefficient, 10-9 m 2 s -1 concn, M Li + Rb + Cs + Cl - /LiCl Cl - /RbCl I - /CsI H 2O/LiCl H 2O/RbCl H 2O/CsI infinitely dilute solution 17,
8 216 J. Phys. Chem. B, Vol. 111, No. 1, 2007 Du et al. L Rβ (t) ) 0 t PRβ (t )dt (12) It has been shown by Mondello and Grest 52 that eqs 11 and 12 give the same results as the Green-Kubo formulation for MD simulations of short-chain alkanes. In this study, we used eqs 11 and 12 to calculate the shear viscosity of the system. To calculate the shear viscosity more accurately, the correlation was integrated for 20 ps, which is roughly twice the rotational diffusion time of water molecules, and averaged over 40 times the entire equilibrium run. Shear viscosity for SPC/E water at 300 K was calculated and compared with experimental results to test the simulation procedure. The calculated viscosity of water was around 1.1 g m -1 s -1 (mpa s), which is in good agreement with the experimental value of 0.88 g m -1 s -1 (mpa s). This indicates that our MD simulations can predict the viscosity of pure water with quite good accuracy. We assume that our calculations of the viscosity of salts in SPC/E water also provide a good representation of the viscosities in real solutions. The viscosities calculated from our MD simulations of brine solutions as a function of solution concentration are shown in Figure 10. As expected, the size of the ions has a significant influence on the viscosity of the solution. When small ions are present (LiCl solution), the system shear viscosity increases monotonically with solution concentration. As the ion size increases (RbCl solution), the system viscosity shows very weak dependence on the solution concentration. Further increases in ion sizes (CsI solution) leads to an obvious decrease of viscosity as a function of solution concentration. This variation of solution viscosity as a function of ion size and solution concentration has also been observed experimentally by several research groups, 15,53 so our simulations show the same trends. In LiCl solution, Li + ions interact strongly with either water molecules or corresponding anions, and form stable tetrahedral structures, which contribute substantially to a thicker system. Though Cl - ions, due to their large size, do not form strong bonds with water molecules, the influence of cations is dominating. This observation is in good agreement with experimental measurements and theoretical modeling in the literature. 53 Consequently, the mobility of the solution will decrease, and system shear viscosity, which describes mobility macroscopically, will increase. The higher the solution concentration, the more significant role the Li + ions play, thus the higher the viscosity. In contrast, when large ions (Cs + and I - ) are present in the solution, loose hydrophobic shells are formed around these ions, and the ion/water interaction is not as strong as water/water interaction, accounting for the decrease in the system shear viscosity. In this research, the solution shear viscosity was calculated in a NPT ensemble, which may introduce errors compared to a NVE ensemble. However, the errors are expected to be small with respect to the obvious changes of solution viscosity with solution concentration. IV. Conclusion In this study the structure and dynamics of concentrated LiCl, RbCl, and CsI aqueous solutions have been studied successfully by using molecular dynamics simulation. It is found that a small ion such as Li +, owing to strong electronegativity, significantly immobilizes the water molecules by tetrahedrally bonding with them, and therefore leads to a more compact structure. The higher the salt concentration, the denser the water molecules are packed as indicated by a monotonic increase of water/water coordination numbers as a function of salt concentration. On Figure 10. System shear viscosity change as a function of solution concentration. the other hand, large ions such as Rb +,Cs +, and I - form weak bonds with water molecules, and a loose hydrophobic hydration shell. Thus, the coordination between water molecules decreases with salt concentration. Also, as the ion size increases, the ion/ water electrostatic interaction becomes less significant when compared to the hydrogen bonding interaction of water molecules. This agrees satisfactorily with the observed dominating increase of naked Cs + /I - ion pair contact, and hydrated Li + / Cl - ion pair contact with respect to an increase in salt concentration. We have concluded that ion size influences the mobility of water molecules in solution. When small ions such as Li + are present, the mobility of water molecules in both the ion hydration shell and the bulk water decreases as a function of salt concentration. In contrast, for solutions containing large ions (CsI and RbCl), the ion/water electrostatic interaction does not contribute significantly to immobilize the water molecules. Consequently, the residence time of water molecules does not show a substantial change with solution concentration. The changes of residence times support the observations of selfdiffusion coefficients of particles as a function of salt concentration, which show that when Li + ions are present, the diffusion coefficients of water molecules in the solution decrease significantly with salt concentration, and when Cs + and I - ions are present, there is no significant change of the water diffusion coefficients with salt concentration. The change of system viscosity with solution concentration as determined from MD simulation in this study successfully compliments the experimental results reported in the literature, 17,38 and provides an in-depth understanding regarding the variation of viscosities as a function of ion sizes and salt concentrations from a molecular perspective. For LiCl solutions, the system viscosity increases monotonically with salt concentration due to the strong ion/water interactions in the solution. As the ion size increases, hydrophobic hydration becomes dominating, and leads to negligible variation of system viscosity with salt concentration in the case of RbCl. Further increase in the ion size to Cs + and I - reveals a noticeable decrease of system viscosity as a function of salt concentration. The excellent agreement between the simulation results and the experimental results for the variation of viscosity with ion size and concentration provides information to describe the phenomenological behavior of alkali halide solutions.
9 Properties of Concentrated Alkali Halide Solutions J. Phys. Chem. B, Vol. 111, No. 1, Acknowledgment. Financial support provided by the Department of Energy, Basic Science Division (Grant No. DE- FG-03-93ER14315) is gratefully acknowledged. In addition, this study was prompted to some extent by collaborative research supported by NSF under grant Nos. INT and INT J.C.R acknowledges support from the National Science Foundation under Grant No. CHE Supporting Information Available: Plots of radial distribution functions. This material is available free of charge via the Internet at References and Notes (1) Nickolov, Z. S.; Miller, J. D. J. Colloid Interface Sci. 2005, 287, 572. (2) Luck, W. A. P.; Schioeberg, D. AdV. Mol. Relax. Interact. Processes 1979, 14, 277. (3) Luck, W. A. P. Water: Compr. Treatise 1973, 3, 211. (4) Luck, W. A. P. Proc. Int. Symp. Fresh Water Sea, 4th 1973, 4, 531. (5) Max, J.-J.; Chapados, C. J. Chem. Phys. 2000, 113, (6) Max, J.-J.; Chapados, C. J. Chem. Phys. 2001, 115, (7) Max, J.-J.; De Blois, S.; Veilleux, A.; Chapados, C. Can. J. Chem. 2001, 79, 13. (8) Terpstra, P.; Combes, D.; Zwick, A. J. Chem. Phys. 1990, 92, 65. (9) Dillon, S. R.; Dougherty, R. C. J. Phys. Chem. A 2002, 106, (10) Kaminsky, M. Z. Phys. Chem. (Muenchen, Germany) 1957, 12, 206. (11) Kaminsky, M. Z. Naturforsch. 1957, 12a, 424. (12) Bryant, R. G. Annu. ReV. Biophys. Biomol. Struct. 1996, 25, 29. (13) Dang, L. X. J. Am. Chem. Soc. 1995, 117, (14) Dang, L. X. Book of Abstracts; 214th ACS National Meeting, Las Vegas, NV, September 7-11, 1997; American Chemical Society: Washington, DC, 1997; PHYS. (15) Hancer, M.; Celik, M. S.; Miller, J. D. J. Colloid Interface Sci. 2001, 235, 150. (16) Lynden-Bell, R. M.; Rasaiah, J. C. J. Chem. Phys. 1997, 107, (17) Koneshan, S.; Rasaiah, J. C.; Lynden-Bell, R. M.; Lee, S. H. J. Phys. Chem. B 1998, 102, (18) Licheri, G.; Piccaluga, G.; Pinna, G. Chem. Phys. Lett. 1975, 35, 119. (19) Licheri, G.; Piccaluga, G.; Pinna, G. Rend. Semin. Fac. Sci. UniV. Cagliari 1972, 42, 85. (20) Licheri, G.; Piccaluga, G.; Pinna, G. Gazz. Chim. Ital. 1972, 102, 847. (21) Lawrence, R. M.; Kruh, R. F. J. Chem. Phys. 1967, 47, (22) Soper, A. K. J. Phys.: Condens. Matter 1997, 9, (23) Enderby, J. E.; Cummings, S.; Herdman, G. J.; Neilson, G. W.; Salmon, P. S.; Skipper, N. J. Phys. Chem. 1987, 91, (24) Enderby, J. E. NATO ASI Ser., Ser. C 1987, 205, 129. (25) Yamagami, M.; Wakita, H.; Yamaguchi, T. J. Chem. Phys. 1995, 103, (26) Berendsen, H. J. J. Comput.-Aided Mol. Des. 1988, 2, 217. (27) Berendsen, H. J. C.; Van Gunsteren, W. F. NATO ASI Ser., Ser. C 1984, 135, 475. (28) Dang, L. X. J. Chem. Phys. 1992, 97, (29) Haile, J. M. Molecular Dynamics Simulation: Elementary Methods; Wiley: New York, (30) Uchida, H.; Matsuoka, M. Fluid Phase Equilib. 2004, 219, 49. (31) Koneshan, S.; Lynden-Bell, R. M.; Rasaiah, J. C. J. Am. Chem. Soc. 1998, 120, (32) Lee, S. H.; Rasaiah, J. C. J. Phys. Chem. 1996, 100, (33) Lee, S. H.; Rasaiah, J. C. J. Chem. Phys. 1994, 101, (34) Lynden-Bell, R. M.; Rasaiah, J. C. J. Chem. Phys. 1996, 105, (35) Dang, L. X. Chem. Phys. Lett. 1992, 200, 21. (36) Dang, L. X.; Smith, D. E. J. Chem. Phys. 1993, 99, (37) Dang, L. X. Chem. Phys. Lett. 1994, 227, 211. (38) Dang, L. X.; Smith, D. E. J. Chem. Phys. 1995, 102, (39) Smith, G. D.; Jaffe, R. L.; Partridge, H. J. Phys. Chem. A 1997, 101, (40) Chowdhuri, S.; Chandra, A. J. Chem. Phys. 2001, 115, (41) Chowdhuri, S.; Chandra, A. J. Chem. Phys. 2003, 118, (42) Smith, D. E.; Dang, L. X. J. Chem. Phys. 1994, 100, (43). Smith, D. E.; Dang, L. X. Chem. Phys. Lett. 1994, 230, 209. (44) Dang, L. X. J. Chem. Phys. 1992, 96, (45) Smith, W.; Forester, T. R. J. Mol. Graphics 1996, 14, 136. (46) Berendsen, H. J. C.; Grigera, J. R.; Straatsma, T. P. J. Phys. Chem. 1987, 91, (47) Melchionna, S.; Ciccotti, G.; Holian, B. L. Mol. Phys. 1993, 78, 533. (48) Impey, R. W.; Madden, P. A.; McDonald, I. R. J. Phys. Chem. 1983, 87, (49) Allen, M. P.; Tildesley, D. J. Computer Simulation of Liquids; Oxford University Press: New York, (50) Koneshan, S.; Rasaiah, J. C. J. Chem. Phys. 2000, 113, (51) Daivis, P. J.; Travis, K. P.; Todd, B. D. J. Chem. Phys. 1996, 104, (52) Mondello, M.; Grest, G. S. J. Chem. Phys. 1997, 106, (53) Jiang, J.; Sandler, S. I. Ind. Eng. Chem. Res. 2003, 42, 6267.
2054-2. Structure and Dynamics of Hydrogen-Bonded Systems. 26-27 October 2009. Hydrogen Bonds and Liquid Water
2054-2 Structure and Dynamics of Hydrogen-Bonded Systems 26-27 October 2009 Hydrogen Bonds and Liquid Water Ruth LYNDEN-BELL University of Cambridge, Department of Chemistry Lensfield Road Cambridge CB2
Hydrogen Bonds The electrostatic nature of hydrogen bonds
Hydrogen Bonds Hydrogen bonds have played an incredibly important role in the history of structural biology. Both the structure of DNA and of protein a-helices and b-sheets were predicted based largely
List the 3 main types of subatomic particles and indicate the mass and electrical charge of each.
Basic Chemistry Why do we study chemistry in a biology course? All living organisms are composed of chemicals. To understand life, we must understand the structure, function, and properties of the chemicals
5s Solubility & Conductivity
5s Solubility & Conductivity OBJECTIVES To explore the relationship between the structures of common household substances and the kinds of solvents in which they dissolve. To demonstrate the ionic nature
Molecular Dynamics Simulations
Molecular Dynamics Simulations Yaoquan Tu Division of Theoretical Chemistry and Biology, Royal Institute of Technology (KTH) 2011-06 1 Outline I. Introduction II. Molecular Mechanics Force Field III. Molecular
INTERMOLECULAR FORCES
INTERMOLECULAR FORCES Intermolecular forces- forces of attraction and repulsion between molecules that hold molecules, ions, and atoms together. Intramolecular - forces of chemical bonds within a molecule
The Hofmeister series
The Hofmeister series a review of monatomic ions near the hydrophobic/water interface Student: Ernst Rösler Student ID: 0105813 Course: Literature Study MSc Chemistry, track Theoretical and Computational
(1) e.g. H hydrogen that has lost 1 electron c. anion - negatively charged atoms that gain electrons 16-2. (1) e.g. HCO 3 bicarbonate anion
GS106 Chemical Bonds and Chemistry of Water c:wou:gs106:sp2002:chem.wpd I. Introduction A. Hierarchy of chemical substances 1. atoms of elements - smallest particles of matter with unique physical and
1 The water molecule and hydrogen bonds in water
The Physics and Chemistry of Water 1 The water molecule and hydrogen bonds in water Stoichiometric composition H 2 O the average lifetime of a molecule is 1 ms due to proton exchange (catalysed by acids
Chapter 13 - LIQUIDS AND SOLIDS
Chapter 13 - LIQUIDS AND SOLIDS Problems to try at end of chapter: Answers in Appendix I: 1,3,5,7b,9b,15,17,23,25,29,31,33,45,49,51,53,61 13.1 Properties of Liquids 1. Liquids take the shape of their container,
The strength of the interaction
The strength of the interaction Host Guest Supramolecule (host-guest complex) When is the host capable to recognize the guest? How do we define selectivity Which element will we use to design the host
Matter, Materials, Crystal Structure and Bonding. Chris J. Pickard
Matter, Materials, Crystal Structure and Bonding Chris J. Pickard Why should a theorist care? Where the atoms are determines what they do Where the atoms can be determines what we can do Overview of Structure
Sample Exercise 8.1 Magnitudes of Lattice Energies
Sample Exercise 8.1 Magnitudes of Lattice Energies Without consulting Table 8.2, arrange the ionic compounds NaF, CsI, and CaO in order of increasing lattice energy. Analyze From the formulas for three
CHAPTER 6 Chemical Bonding
CHAPTER 6 Chemical Bonding SECTION 1 Introduction to Chemical Bonding OBJECTIVES 1. Define Chemical bond. 2. Explain why most atoms form chemical bonds. 3. Describe ionic and covalent bonding.. 4. Explain
LECTURE 11 : GLASSY DYNAMICS - Intermediate scattering function - Mean square displacement and beyond - Dynamic heterogeneities - Isoconfigurational
LECTURE 11 : GLASSY DYNAMICS - Intermediate scattering function - Mean square displacement and beyond - Dynamic heterogeneities - Isoconfigurational Ensemble - Energy landscapes A) INTERMEDIATE SCATTERING
H 2O gas: molecules are very far apart
Non-Covalent Molecular Forces 2/27/06 3/1/06 How does this reaction occur: H 2 O (liquid) H 2 O (gas)? Add energy H 2O gas: molecules are very far apart H 2O liquid: bonding between molecules Use heat
AP Chemistry A. Allan Chapter 8 Notes - Bonding: General Concepts
AP Chemistry A. Allan Chapter 8 Notes - Bonding: General Concepts 8.1 Types of Chemical Bonds A. Ionic Bonding 1. Electrons are transferred 2. Metals react with nonmetals 3. Ions paired have lower energy
Chapter 2: The Chemical Context of Life
Chapter 2: The Chemical Context of Life Name Period This chapter covers the basics that you may have learned in your chemistry class. Whether your teacher goes over this chapter, or assigns it for you
Forensic Science Standards and Benchmarks
Forensic Science Standards and Standard 1: Understands and applies principles of scientific inquiry Power : Identifies questions and concepts that guide science investigations Uses technology and mathematics
Section Activity #1: Fill out the following table for biology s most common elements assuming that each atom is neutrally charged.
LS1a Fall 2014 Section Week #1 I. Valence Electrons and Bonding The number of valence (outer shell) electrons in an atom determines how many bonds it can form. Knowing the number of valence electrons present
POWDER X-RAY DIFFRACTION: STRUCTURAL DETERMINATION OF ALKALI HALIDE SALTS
EXPERIMENT 4 POWDER X-RAY DIFFRACTION: STRUCTURAL DETERMINATION OF ALKALI HALIDE SALTS I. Introduction The determination of the chemical structure of molecules is indispensable to chemists in their effort
Why? Intermolecular Forces. Intermolecular Forces. Chapter 12 IM Forces and Liquids. Covalent Bonding Forces for Comparison of Magnitude
1 Why? Chapter 1 Intermolecular Forces and Liquids Why is water usually a liquid and not a gas? Why does liquid water boil at such a high temperature for such a small molecule? Why does ice float on water?
Type of Chemical Bonds
Type of Chemical Bonds Covalent bond Polar Covalent bond Ionic bond Hydrogen bond Metallic bond Van der Waals bonds. Covalent Bonds Covalent bond: bond in which one or more pairs of electrons are shared
6.5 Periodic Variations in Element Properties
324 Chapter 6 Electronic Structure and Periodic Properties of Elements 6.5 Periodic Variations in Element Properties By the end of this section, you will be able to: Describe and explain the observed trends
Sample Exercise 8.1 Magnitudes of Lattice Energies
Sample Exercise 8.1 Magnitudes of Lattice Energies Without consulting Table 8.2, arrange the following ionic compounds in order of increasing lattice energy: NaF, CsI, and CaO. Analyze: From the formulas
CHAPTER 10: INTERMOLECULAR FORCES: THE UNIQUENESS OF WATER Problems: 10.2, 10.6,10.15-10.33, 10.35-10.40, 10.56-10.60, 10.101-10.
CHAPTER 10: INTERMOLECULAR FORCES: THE UNIQUENESS OF WATER Problems: 10.2, 10.6,10.15-10.33, 10.35-10.40, 10.56-10.60, 10.101-10.102 10.1 INTERACTIONS BETWEEN IONS Ion-ion Interactions and Lattice Energy
Chapter 2 The Chemical Context of Life
Chapter 2 The Chemical Context of Life Multiple-Choice Questions 1) About 25 of the 92 natural elements are known to be essential to life. Which four of these 25 elements make up approximately 96% of living
Since we will be dealing with aqueous acid and base solution, first we must examine the behavior of water.
Acids and Bases Know the definition of Arrhenius, Bronsted-Lowry, and Lewis acid and base. Autoionization of Water Since we will be dealing with aqueous acid and base solution, first we must examine the
Acids and Bases: A Brief Review
Acids and : A Brief Review Acids: taste sour and cause dyes to change color. : taste bitter and feel soapy. Arrhenius: acids increase [H ] bases increase [OH ] in solution. Arrhenius: acid base salt water.
Chapter 4: Structure and Properties of Ionic and Covalent Compounds
Chapter 4: Structure and Properties of Ionic and Covalent Compounds 4.1 Chemical Bonding o Chemical Bond - the force of attraction between any two atoms in a compound. o Interactions involving valence
Which substance contains positive ions immersed in a sea of mobile electrons? A) O2(s) B) Cu(s) C) CuO(s) D) SiO2(s)
BONDING MIDTERM REVIEW 7546-1 - Page 1 1) Which substance contains positive ions immersed in a sea of mobile electrons? A) O2(s) B) Cu(s) C) CuO(s) D) SiO2(s) 2) The bond between hydrogen and oxygen in
Modern Construction Materials Prof. Ravindra Gettu Department of Civil Engineering Indian Institute of Technology, Madras
Modern Construction Materials Prof. Ravindra Gettu Department of Civil Engineering Indian Institute of Technology, Madras Module - 2 Lecture - 2 Part 2 of 2 Review of Atomic Bonding II We will continue
NaCl Lattice Science Activities
NaCl Lattice Science Activities STEM: The Science of Salt Using a Salt Lattice Model Teacher Notes Science Activities A Guided-Inquiry Approach Using the 3D Molecular Designs NaCl Lattice Model Classroom
stoichiometry = the numerical relationships between chemical amounts in a reaction.
1 REACTIONS AND YIELD ANSWERS stoichiometry = the numerical relationships between chemical amounts in a reaction. 2C 8 H 18 (l) + 25O 2 16CO 2 (g) + 18H 2 O(g) From the equation, 16 moles of CO 2 (a greenhouse
Physics 9e/Cutnell. correlated to the. College Board AP Physics 1 Course Objectives
Physics 9e/Cutnell correlated to the College Board AP Physics 1 Course Objectives Big Idea 1: Objects and systems have properties such as mass and charge. Systems may have internal structure. Enduring
States of Matter CHAPTER 10 REVIEW SECTION 1. Name Date Class. Answer the following questions in the space provided.
CHAPTER 10 REVIEW States of Matter SECTION 1 SHORT ANSWER Answer the following questions in the space provided. 1. Identify whether the descriptions below describe an ideal gas or a real gas. ideal gas
Lecture 22 The Acid-Base Character of Oxides and Hydroxides in Aqueous Solution
2P32 Principles of Inorganic Chemistry Dr. M. Pilkington Lecture 22 The Acid-Base Character of Oxides and Hydroxides in Aqueous Solution Oxides; acidic, basic, amphoteric Classification of oxides - oxide
KINETIC MOLECULAR THEORY OF MATTER
KINETIC MOLECULAR THEORY OF MATTER The kinetic-molecular theory is based on the idea that particles of matter are always in motion. The theory can be used to explain the properties of solids, liquids,
Use the Force! Noncovalent Molecular Forces
Use the Force! Noncovalent Molecular Forces Not quite the type of Force we re talking about Before we talk about noncovalent molecular forces, let s talk very briefly about covalent bonds. The Illustrated
SELF DIFFUSION COEFFICIENT OF LENNARD-JONES FLUID USING TEMPERATURE DEPENDENT INTERACTION PARAMETERS AT DIFFERENT PRESSURES
JIChE06 The Sixth Jordan International Chemical Engineering Conference 12 14 March 2012, Amman, Jordan SELF DIFFUSION COEFFICIENT OF LENNARD-JONES FLUID USING TEMPERATURE DEPENDENT INTERACTION PARAMETERS
Chem 106 Thursday Feb. 3, 2011
Chem 106 Thursday Feb. 3, 2011 Chapter 13: -The Chemistry of Solids -Phase Diagrams - (no Born-Haber cycle) 2/3/2011 1 Approx surface area (Å 2 ) 253 258 Which C 5 H 12 alkane do you think has the highest
Element of same atomic number, but different atomic mass o Example: Hydrogen
Atomic mass: p + = protons; e - = electrons; n 0 = neutrons p + + n 0 = atomic mass o For carbon-12, 6p + + 6n 0 = atomic mass of 12.0 o For chlorine-35, 17p + + 18n 0 = atomic mass of 35.0 atomic mass
Chemistry 1050 Chapter 13 LIQUIDS AND SOLIDS 1. Exercises: 25, 27, 33, 39, 41, 43, 51, 53, 57, 61, 63, 67, 69, 71(a), 73, 75, 79
Chemistry 1050 Chapter 13 LIQUIDS AND SOLIDS 1 Text: Petrucci, Harwood, Herring 8 th Edition Suggest text problems Review questions: 1, 5!11, 13!17, 19!23 Exercises: 25, 27, 33, 39, 41, 43, 51, 53, 57,
Chapter 2 Polar Covalent Bonds: Acids and Bases
John E. McMurry www.cengage.com/chemistry/mcmurry Chapter 2 Polar Covalent Bonds: Acids and Bases Modified by Dr. Daniela R. Radu Why This Chapter? Description of basic ways chemists account for chemical
Thermodynamics of Crystal Formation
Thermodynamics of Crystal Formation! All stable ionic crystals have negative standard enthalpies of formation, ΔH o f, and negative standard free energies of formation, ΔG o f. Na(s) + ½ Cl 2 (g) NaCl(s)
Molecular Models in Biology
Molecular Models in Biology Objectives: After this lab a student will be able to: 1) Understand the properties of atoms that give rise to bonds. 2) Understand how and why atoms form ions. 3) Model covalent,
Name period AP chemistry Unit 2 worksheet Practice problems
Name period AP chemistry Unit 2 worksheet Practice problems 1. What are the SI units for a. Wavelength of light b. frequency of light c. speed of light Meter hertz (s -1 ) m s -1 (m/s) 2. T/F (correct
SIZE OF A MOLECULE FROM A VISCOSITY MEASUREMENT
Experiment 8, page 1 Version of April 25, 216 Experiment 446.8 SIZE OF A MOLECULE FROM A VISCOSITY MEASUREMENT Theory Viscous Flow. Fluids attempt to minimize flow gradients by exerting a frictional force,
Chemical Bonds and Groups - Part 1
hemical Bonds and Groups - Part 1 ARB SKELETS arbon has a unique role in the cell because of its ability to form strong covalent bonds with other carbon atoms. Thus carbon atoms can join to form chains.
Molecular dynamics calculations and the analysis of results
Molecular dynamics calculations and the analysis of results Dr Billy D. Todd Centre for Molecular Simulation Swinburne University of Technology PO Box 218, Hawthorn Victoria 3122, Australia Email: [email protected]
Understanding the p-n Junction by Dr. Alistair Sproul Senior Lecturer in Photovoltaics The Key Centre for Photovoltaic Engineering, UNSW
Understanding the p-n Junction by Dr. Alistair Sproul Senior Lecturer in Photovoltaics The Key Centre for Photovoltaic Engineering, UNSW The p-n junction is the fundamental building block of the electronic
Collision of a small bubble with a large falling particle
EPJ Web of Conferences 67, 212 (214) DOI: 1.11/ epjconf/ 21467212 C Owned by the authors, published by EDP Sciences, 214 Collision of a small bubble with a large falling particle Jiri Vejrazka 1,a, Martin
Chapter 10 Liquids & Solids
1 Chapter 10 Liquids & Solids * 10.1 Polar Covalent Bonds & Dipole Moments - van der Waals constant for water (a = 5.28 L 2 atm/mol 2 ) vs O 2 (a = 1.36 L 2 atm/mol 2 ) -- water is polar (draw diagram)
Oxidation / Reduction Handout Chem 2 WS11
Oxidation / Reduction Handout Chem 2 WS11 The original concept of oxidation applied to reactions where there was a union with oxygen. The oxygen was either furnished by elemental oxygen or by compounds
Health Science Chemistry I CHEM-1180 Experiment No. 15 Molecular Models (Revised 05/22/2015)
(Revised 05/22/2015) Introduction In the early 1900s, the chemist G. N. Lewis proposed that bonds between atoms consist of two electrons apiece and that most atoms are able to accommodate eight electrons
Brønsted-Lowry Acids and Bases
Brønsted-Lowry Acids and Bases 1 According to Brønsted and Lowry, an acid-base reaction is defined in terms of a proton transfer. By this definition, the reaction of Cl in water is: Cl(aq) + Cl (aq) +
Chemistry B11 Chapter 6 Solutions and Colloids
Chemistry B11 Chapter 6 Solutions and Colloids Solutions: solutions have some properties: 1. The distribution of particles in a solution is uniform. Every part of the solution has exactly the same composition
Chapter 2 Polar Covalent Bonds; Acids and Bases
John E. McMurry http://www.cengage.com/chemistry/mcmurry Chapter 2 Polar Covalent Bonds; Acids and Bases Javier E. Horta, M.D., Ph.D. University of Massachusetts Lowell Polar Covalent Bonds: Electronegativity
A mutual electrical attraction between the nuclei and valence electrons of different atoms that binds the atoms together is called a(n)
Chemistry I ATOMIC BONDING PRACTICE QUIZ Mr. Scott Select the best answer. 1) A mutual electrical attraction between the nuclei and valence electrons of different atoms that binds the atoms together is
Unit 11 Practice. Name: Class: Date: Multiple Choice Identify the choice that best completes the statement or answers the question.
Name: Class: Date: Unit 11 Practice Multiple Choice Identify the choice that best completes the statement or answers the question. 1) Crystalline solids. A) have their particles arranged randomly B) have
Candidate Style Answer
Candidate Style Answer Chemistry A Unit F321 Atoms, Bonds and Groups High banded response This Support Material booklet is designed to accompany the OCR GCE Chemistry A Specimen Paper F321 for teaching
BOND TYPES: THE CLASSIFICATION OF SUBSTANCES
BOND TYPES: THE CLASSIFICATION OF SUBSTANCES Every (pure) substance has a unique set of intrinsic properties which distinguishes it from all other substances. What inferences, if any can be made from a
Sketch the model representation of the first step in the dissociation of water. H 2. O (l) H + (aq) + OH- (aq) + H 2. OH - (aq) + H 3 O+ (aq)
Lesson Objectives Students will: Create a physical representation of the autoionization of water using the water kit. Describe and produce a physical representation of the dissociation of a strong acid
Chemistry. The student will be able to identify and apply basic safety procedures and identify basic equipment.
Chemistry UNIT I: Introduction to Chemistry The student will be able to describe what chemistry is and its scope. a. Define chemistry. b. Explain that chemistry overlaps many other areas of science. The
Explain the ionic bonds, covalent bonds and metallic bonds and give one example for each type of bonds.
Problem 1 Explain the ionic bonds, covalent bonds and metallic bonds and give one example for each type of bonds. Ionic Bonds Two neutral atoms close to each can undergo an ionization process in order
Anatomy and Physiology Placement Exam 2 Practice with Answers at End!
Anatomy and Physiology Placement Exam 2 Practice with Answers at End! General Chemical Principles 1. bonds are characterized by the sharing of electrons between the participating atoms. a. hydrogen b.
JBS FUNDAMENT Thermofluor Screen
Cat. No. CS-330 Amount 1 Kit For in vitro use only. Quality guaranteed for 3 months. Store at 4 C. Application Screen for thermal stability of proteins as a function of the FUNDAMENTAL variables ph and
Chemical Reactions in Water Ron Robertson
Chemical Reactions in Water Ron Robertson r2 f:\files\courses\1110-20\2010 possible slides for web\waterchemtrans.doc Properties of Compounds in Water Electrolytes and nonelectrolytes Water soluble compounds
EXPERIMENT 9 Dot Structures and Geometries of Molecules
EXPERIMENT 9 Dot Structures and Geometries of Molecules INTRODUCTION Lewis dot structures are our first tier in drawing molecules and representing bonds between the atoms. The method was first published
molecular aggregates would then be present in the water: e.g., linear chains containing
VISCOSITY MEASUREMENTS OF ALCOHOL-WATER MIXTURES AND THE STRUCTURE OF WATER BY M. AGENO AND C. FRONTALI PHYSICS LABORATORY, ISTITUTO SUPERIORE DI SANITA, ROME, ITALY Communicated by Emilio Segr', February
Name Class Date. In the space provided, write the letter of the term or phrase that best completes each statement or best answers each question.
Assessment Chapter Test A Chapter: States of Matter In the space provided, write the letter of the term or phrase that best completes each statement or best answers each question. 1. The kinetic-molecular
CHAPTER 6 REVIEW. Chemical Bonding. Answer the following questions in the space provided.
Name Date lass APTER 6 REVIEW hemical Bonding SETIN 1 SRT ANSWER Answer the following questions in the space provided. 1. a A chemical bond between atoms results from the attraction between the valence
SOLUBILITY, IONIC STRENGTH AND ACTIVITY COEFFICIENTS
SOLUBILITY, IONIC STRENGTH AND ACTIVITY COEFFICIENTS References: 1. See `References to Experiments' for text references.. W. C. Wise and C. W. Davies, J. Chem. Soc., 73 (1938), "The Conductivity of Calcium
Chapter Outline. Review of Atomic Structure Electrons, Protons, Neutrons, Quantum mechanics of atoms, Electron states, The Periodic Table
Review of Atomic Structure Electrons, Protons, Neutrons, Quantum mechanics of atoms, Electron states, The Periodic Table Atomic Bonding in Solids Bonding Energies and Forces Periodic Table Chapter Outline
CHEMISTRY BONDING REVIEW
Answer the following questions. CHEMISTRY BONDING REVIEW 1. What are the three kinds of bonds which can form between atoms? The three types of Bonds are Covalent, Ionic and Metallic. Name Date Block 2.
Chemical Bonds. Chemical Bonds. The Nature of Molecules. Energy and Metabolism < < Covalent bonds form when atoms share 2 or more valence electrons.
The Nature of Molecules Chapter 2 Energy and Metabolism Chapter 6 Chemical Bonds Molecules are groups of atoms held together in a stable association. Compounds are molecules containing more than one type
NET IONIC EQUATIONS. A balanced chemical equation can describe all chemical reactions, an example of such an equation is:
NET IONIC EQUATIONS A balanced chemical equation can describe all chemical reactions, an example of such an equation is: NaCl + AgNO 3 AgCl + NaNO 3 In this case, the simple formulas of the various reactants
Bonds. Bond Length. Forces that hold groups of atoms together and make them function as a unit. Bond Energy. Chapter 8. Bonding: General Concepts
Bonds hapter 8 Bonding: General oncepts Forces that hold groups of atoms together and make them function as a unit. Bond Energy Bond Length It is the energy required to break a bond. The distance where
Chemical Sputtering. von Kohlenstoff durch Wasserstoff. W. Jacob
Chemical Sputtering von Kohlenstoff durch Wasserstoff W. Jacob Centre for Interdisciplinary Plasma Science Max-Planck-Institut für Plasmaphysik, 85748 Garching Content: Definitions: Chemical erosion, physical
A pure covalent bond is an equal sharing of shared electron pair(s) in a bond. A polar covalent bond is an unequal sharing.
CHAPTER EIGHT BNDING: GENERAL CNCEPT or Review 1. Electronegativity is the ability of an atom in a molecule to attract electrons to itself. Electronegativity is a bonding term. Electron affinity is the
Molecular Cell Biology
Harvey Lodish Arnold Berk Paul Matsudaira Chris A. Kaiser Monty Krieger Matthew P. Scott Lawrence Zipursky James Darnell Molecular Cell Biology Fifth Edition Chapter 2: Chemical Foundations Copyright 2004
CHEMISTRY STANDARDS BASED RUBRIC ATOMIC STRUCTURE AND BONDING
CHEMISTRY STANDARDS BASED RUBRIC ATOMIC STRUCTURE AND BONDING Essential Standard: STUDENTS WILL UNDERSTAND THAT THE PROPERTIES OF MATTER AND THEIR INTERACTIONS ARE A CONSEQUENCE OF THE STRUCTURE OF MATTER,
PERIODIC TABLE OF GROUPS OF ELEMENTS Elements can be classified using two different schemes.
1 PERIODIC TABLE OF GROUPS OF ELEMENTS Elements can be classified using two different schemes. Metal Nonmetal Scheme (based on physical properties) Metals - most elements are metals - elements on left
Chapter 6. Solution, Acids and Bases
Chapter 6 Solution, Acids and Bases Mixtures Two or more substances Heterogeneous- different from place to place Types of heterogeneous mixtures Suspensions- Large particles that eventually settle out
Theme 3: Bonding and Molecular Structure. (Chapter 8)
Theme 3: Bonding and Molecular Structure. (Chapter 8) End of Chapter questions: 5, 7, 9, 12, 15, 18, 23, 27, 28, 32, 33, 39, 43, 46, 67, 77 Chemical reaction valence electrons of atoms rearranged (lost,
Insight Into Chain Dimensions in PEO/Water Solutions
Insight Into Chain Dimensions in PEO/Water Solutions BOUALEM HAMMOUDA, DEREK L. HO Center for Neutron Research and Polymers Division, National Institute of Standards and Technology, 100 Bureau Drive, Gaithersburg,
1.1.2. thebiotutor. AS Biology OCR. Unit F211: Cells, Exchange & Transport. Module 1.2 Cell Membranes. Notes & Questions.
thebiotutor AS Biology OCR Unit F211: Cells, Exchange & Transport Module 1.2 Cell Membranes Notes & Questions Andy Todd 1 Outline the roles of membranes within cells and at the surface of cells. The main
The Synthesis of trans-dichlorobis(ethylenediamine)cobalt(iii) Chloride
CHEM 122L General Chemistry Laboratory Revision 2.0 The Synthesis of trans-dichlorobis(ethylenediamine)cobalt(iii) Chloride To learn about Coordination Compounds and Complex Ions. To learn about Isomerism.
Nuclear Structure. particle relative charge relative mass proton +1 1 atomic mass unit neutron 0 1 atomic mass unit electron -1 negligible mass
Protons, neutrons and electrons Nuclear Structure particle relative charge relative mass proton 1 1 atomic mass unit neutron 0 1 atomic mass unit electron -1 negligible mass Protons and neutrons make up
Lewis Dot Notation Ionic Bonds Covalent Bonds Polar Covalent Bonds Lewis Dot Notation Revisited Resonance
Lewis Dot Notation Ionic Bonds Covalent Bonds Polar Covalent Bonds Lewis Dot Notation Revisited Resonance Lewis Dot notation is a way of describing the outer shell (also called the valence shell) of an
Lecture 3: Models of Solutions
Materials Science & Metallurgy Master of Philosophy, Materials Modelling, Course MP4, Thermodynamics and Phase Diagrams, H. K. D. H. Bhadeshia Lecture 3: Models of Solutions List of Symbols Symbol G M
Chapter 6 An Overview of Organic Reactions
John E. McMurry www.cengage.com/chemistry/mcmurry Chapter 6 An Overview of Organic Reactions Why this chapter? To understand organic and/or biochemistry, it is necessary to know: -What occurs -Why and
10.7 Kinetic Molecular Theory. 10.7 Kinetic Molecular Theory. Kinetic Molecular Theory. Kinetic Molecular Theory. Kinetic Molecular Theory
The first scheduled quiz will be given next Tuesday during Lecture. It will last 5 minutes. Bring pencil, calculator, and your book. The coverage will be pp 364-44, i.e. Sections 0.0 through.4. 0.7 Theory
The polarity of water molecules results in hydrogen bonding [3]
GUIDED READING - Ch. 3 PROPERTIES OF WATER NAME: Please print out these pages and HANDWRITE the answers directly on the printouts. Typed work or answers on separate sheets of paper will not be accepted.
Introduction, Noncovalent Bonds, and Properties of Water
Lecture 1 Introduction, Noncovalent Bonds, and Properties of Water Reading: Berg, Tymoczko & Stryer: Chapter 1 problems in textbook: chapter 1, pp. 23-24, #1,2,3,6,7,8,9, 10,11; practice problems at end
