BDL4681XU BDL4675XU. Video Wall Installation Guide

Transcription

1 BDL4681XU BDL4675XU Video Wall Installation Guide

2 Video walls can create a stunning visual effect, attracting attention and audiences to view your messages and other video content. To ensure optimal performance from your video wall, we urge you to read through this document as it contains very important information which will help avoid technical issues in the future. Before You Start Before commencing on implementing your video wall, and to avoid issues and problems later that could void your warranty, we strongly recommend that you follow these steps to ensure important conditions are met. Your video wall must be installed on a flat and level surface which is strong enough to bear its weight. If mounting the video wall on a physical wall, ensure that the mounting bracket is firmly and securely attached to the wall, and that the complete structure is able to support the entire weight of the video wall. If you plan to cascade your displays in Landscape mode, do NOT remove the plastic screws on the bottom of each display. These screws offer protection to the unit by cushioning the weight from the display above. Removing the screw may result in damage due to the direct transfer of weight from above, and could lead to a pinkish hue around the displayed image. When mounted in a video wall, multiple displays emit a considerable amount of heat. To avoid overheating and to ensure the longest possible lifetime for your products, make sure that there is an absolute minimum of 6cm clearance between the wall or structure and the video wall. we recommend a minimum of 10cm clearance to ensure better air flow and heat dissipation. Because of the fragile nature of the LCD display, and because it is easily damaged from scratches or pressure, we recommend the use of appropriate padding materials during installation to offer better protection. Items needed for Installation Corner Alignment Brackets Bottom (B) Middle (M) Top (T) Left (L) Right (R) M4 x 10mm Screws - 12x (F) Installation Cascading Displays in Landscape Mode 1. Mount and fasten the display on the mounting bracket or stand by carefully threading the screws through the respective holes and tightening with a Philips (cross) screwdriver. 2. Link the displays by placing a corner alignment bracket in to the respective slot on the rear side of each panel, making sure to insert the right bracket in to each slot (B for Bottom, M for middle, T for Top, L for left and R for right). Fasten with 2 screws per tab (except for M which uses 4) 3. Check the installation, and make sure that there is contact between the displays on the top and the bottom. via the spacer screws as shown below. Failure to do this may damage your LCD screens through the direct transfer of weight. 4. Ensure that there is at least 60mm clearance between the mounted displays and the wall or structure in order to allow optimal heat dissipation and ventilation. 60mm Note: In this guide, procedures described are based on the installation of a standard 2 x 2 display configuration (2 displays horizontally, and 2 displays vertically). For video walls consisting of more displays, the number of corner alignment kits and screws may vary.

3 Installation Cascading Displays in Portrait Mode 1. To mount in portrait mode, remove the spacer screws in each display, indicated by the dotted circles in the figure below. 2. Mount and fasten the display on the mounting bracket or stand by carefully threading the screws through the respective holes and tightening with a Philips (cross) screwdriver. 3. Link the displays by placing a corner alignment bracket in to the respective slot on the rear side of each panel, making sure to insert the right bracket in to each slot (L for Bottom, M for middle, R for Top, B for left and T for right). Fasten with 2 screws per tab (except for M which requires 4) 4. Ensure that there is at least 60mm clearance between the mounted displays and the wall or structure in order to allow optimal heat dissipation and ventilation. 60mm Edge Finishing Installation Whether used as a standalone unit or as a part of a video wall, the edge finishing kit will transform your BDL4681XU/BDL4675XU in to a most stylish and elegant display. Mounting the edge-finishing kit is childsplay - just follow these simple instructions and your display or video wall will be ready in no time at all. Inside your edge finishing kit you will find the following components: Cosmetic Plates Top (C) Bottom (D) Left (B) Right (A) Flat Enclosure (E) Corner Enclosure (F) M4 x 6mm Screw (G) M4 x 12mm Screw (H)

4 Installation For a Landscape Video Wall For Standalone Unit 1. Mount the cosmetic plates in their respective places on the edge of your display, and screw in to place using the 12mm M4 screws. 1. Mount the cosmetic plates in their respective places on the edge of your display, and screw in to place using the 12mm M4 screws. 2. On each corner, mount a corner enclosure piece and fasten each one with 2 of the 6mm M4 screws 2. On each corner, mount a corner enclosure piece and fasten each one with 2 of the 6mm M4 screws. Where the displays meet, use a flat enclosure piece, and fasten each of these too with 2 of the 6mm M4 screws. For a Portrait Video Wall 1. Mount the cosmetic plates in their respective places on the edge of your display, and screw in to place using the 12mm M4 screws. 2. On each corner, mount a corner enclosure piece and fasten each one with 2 of the 6mm M4 screws. Where the displays meet, use a flat enclosure piece, and fasten each of these too with 2 of the 6mm M4 screws. Important: When mounting, make sure that all edge enclosure pieces are fitted to the respective positions (i.e. bottom to bottom, etc). When rotating, the RIGHT side of the displays should be on the bottom. Important: When mounting, make sure that all edge enclosure pieces are fitted to the respective positions (i.e. bottom to bottom, etc) Troubleshooting If you experience a colour difference among the displays in the same video wall, swap the signal connections to confirm whether the issue lies in the signal or the displays. If the problem is with the signal, check the following: Do not connect more than 2 signal splitters in a serial manner. Use the same brand and model signal splitters wherever possible. Do not use cables longer than 10 metres to avoid loss of signal strength. Use the same brand and model PC graphics cards as colour differences may occur at different signal intensity. If the problem is with the displays, ensure the following settings are identical in each display: BRIGHTNESS, CONTRAST LEVEL, TINT, COLOUR, COL- OUR TEMPERATURE, LIGHT SENSOR and SMART CON- TRAST in the PICTURE menu. The BRIGHTNESS setting in PANEL SAVING inside the CON- FIGURATION menu The GAMMA SELECTION and SMART POWER settings inside the ADVANCED OPTIONS menu. For additional assistance, please contact your local sales representative or visit the website:

5 Public Signage Solutions Remote Control Extender RCX4601/00 Easily control your Video Wall The Remote Control Extender enables you to control your video wall from every possible angle! Simple control of your Video Walls to make your audience spellbound With the Remote Control Extender The Remote Control Extender offers you the possibility to extend the IR signal. The IR sensor on our range of zero bezel displays is placed in the back cover of the display. The extender makes use of the IR-in function of the display to make the control and set up of your bezel-less displays easy. One single Remote Control Extender is able to control one display. Compatible with BDL4675XU and BDL4681XU

6 Chief: all-new FUSION Solución para Video Wall totalmente nueva Los LSMVU y MSMVU son soportes para video wall de fácil instalación y mantenimiento, que ahorran tiempo y costes. Inspirada en los comentarios de los instaladores, la nueva serie de soportes FUSION (MSMVU/LSMVU) se extienden desde la pared 178 mm., para facilitar el acceso a los cables y mantenimiento en instalaciones de difícil acceso, incluso en las pantallas centrales de un video wall. El ajuste fino de nivel asegura una verticalidad perfecta de la pantalla, incluso si la pared no lo está. Esta gama de soportes incluye una amplia variedad de características que facilitan hacer la instalación y el mantenimiento de las instalaciones multi-pantalla en un suspiro. El sistema ControlZoneTM permite el ajuste fino de altura y nivel después de la instalación. Ajuste las pantallas lateralmente con el Centerless, un ajuste post instalación que permite acelerar la misma y simplifica el mantenimiento general con un simple deslizamiento para separarlas. El exclusivo ClickConnect de Chief emite un clic audible cuando las pantallas están correctamente encajadas en el soporte así se sabe que la instalación es segura, además se puede añadir un candado para mayor seguridad. Los nuevos soportes extraíbles FUSION de Chief ahorran tiempo y dinero en instalaciones de video wall. Los soportes se pueden utilizar en configuraciones de video wall de 2 x 2 o más con pantallas de