Improve the Speed of your System Startup

Transcription

1 Improve the Speed of your System Startup PowerLogic Factory Assembled Enclosures For metering, communications and control

2 Square D PowerLogic Factory Assembled Enclosures offer a wide range of designs for metering, communications, and control applications to simplify retrofit installations. Our enclosures are designed to order as a free-standing or wall-mounted system. With PowerLogic Factory Assembled Enclosures, you ll receive professionally crafted, factory tested, pre-wired enclosures that will greatly improve the speed of your system startup. All backed by the Square D quality standard of excellence. Service entrances and onsite generation Our Factory Assembled Enclosure units are available for your entire PowerLogic energy and power management system or automated power system controls project from the service entrance for revenue metering to high density tenant sub-metering and just about everything in between. If you don t see what you had in mind and would like to special order a custom enclosure, we offer design services to accommodate your needs. Power mitigation and main power distribution equipment Advantages: Designed to current NEC and UL standards Equipped with hazard and safety labels UL/CUL 508A listed* Efficient panel layout and well marked terminals reduce wiring errors and needless troubleshooting Complete with necessary documentation and mounting hardware for quick and easy installation PDUs and dataservers Processes, lines, machines or equipment Tenants, departments and subcontractors Engineering, planning, maintenance * Applies to sections 1-16.

3 Table of Contents Service Entrance/Utility Revenue Main/Critical Circuit Main + Multiple Feeders Meter (Qty) Display Type 12 Type 4 Type 1 Type 3R ION8600 meter (1) I 1 CM4000 series circuit monitor (1-4) R 2 ION7550 /ION7650 series meter (1-4) I 3 CM4000 series circuit monitors (1) + PM820 power meter (1-8) R + R 4 ION7550 /ION7650 series meters (1) + ION6200 series meter (1-8) I + R 5 Secondary Mains Feeders High Density Metering Communications Custom Enclosures Drawout Retrofit Cradles CM3000 series circuit monitor (1-4) R 6 ION7300 series meter (1-4) I or R 7 ION6200 series meter (1-4) R 8 PM820 power meter (1-4) R 9 ION6200 series power meter (1, 2, 4, 6, 8, 10, 12) PM800 series power meter (1, 2, 4, 6, 8, 10, 12) HDM - ION6200 series power meter (1 or 4) HDM - PM700 series power meter (1, 4, 8, 16) HDM - PM210 power meter (1, 4, 8, 16) R R Multiple Circuit Meter R or N 12 EGX (1) Ethernet switch (1) + EGX (1-3) I I I Light Industrial Applications 10 Commercial Building Applications 13 ION7550RTU (1-4) R or N 14 Niobrara Research & Development (NR&D) (1) 15 PM800 series power meter ION7300 series power meter ION6200 series power meter Controls 16 I I I I * Consult factory representative for special order. * ION6200 Only I = Integrated Display R = Remote Display N = No Display

4 1 Service Entrance/Revenue Utility PowerLogic ION8600 Factory Assembled Enclosures Type 3R Description: The ION8600 series socket meter enclosure is an ideal metering solution for monitoring electrical distribution networks, service entrances and substations requiring revenue accuracy and power quality analysis capabilities. This industrial enclosure is UL listed and equipped with pad-lockable latch and removable door. Multiple ION8600 units can be networked together via Ethernet or RS-485 using Modbus, ION or other industry standard communication protocols. Features Assemblies include meter and devices wired to terminal blocks, voltage disconnect and current transformer (CT) shorting block. Serial & Ethernet Communications are options for all units. Digital and/or Analog Input/Output (I/O) are options for all units. Units are available with optional 10-Pole test switch installed for voltage and CT testing, and calibration. Units are available with optional built in bar type CT s installed (Transocket Lever Bypass). Tailored to any meter system voltage type : 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase 240V, 480V & 600V Delta Three-Phase Supports Single Voltage Sources for Outdoor (Type 3R) applications Wall mountable and easy to install, using concealed holes in the back of the enclosure. Carbon steel construction, with industry standard ANSI 61 gray powder-coat finish. Custom engraved nameplates are available for all units. Enclosure Dimensions - see ordering information

5 Service Entrance/Revenue Utility 1 Ordering Information Model Order code Description Factory Assembled: Type 3R ION 8600 Meter Enclosures 9761E Typical lead time is 6 - weeks Meter Meter Type (meter included with enclosure) 8600 ION8600 Meter Enclosure Type - Indoor/Outdoor Applications - NEMA 3R A0 B0 C0 D0 E0 NEMA 3R Enclosure with one 8xxx Form 9S (13 Terminal) meter Installed and Wired - Dim 20 H x 12 W x 5-1/8 D NEMA 3R Enclosure with one 8xxx Form 35S (8 Terminal) meter Installed and Wired - Dim 20 H x 12 W x 5-1/8 D NEMA 3R Enclosure with one 8xxx Form 36S (13 Terminal) meter Installed and Wired - Dim 20 H x 12 W x 5-1/8 D NEMA 3R Enclosure with one 8xxx Form 39S (15 Terminal) meter Installed and Wired - Dim 20 H x 12 W x 5-1/8 D NEMA 3R Enclosure with one 8xxx Form 76S (15 Terminal) meter Installed and Wired - Dim 20 H x 12 W x 5-1/8 D Enclosure Type - Transocket Lever Bypass Enclosure - Indoor / Outdoor Applications - NEMA 3R Bar Type CT s and Neutral Bar (if Applicable) are Located Behind a Protected Swing Door Supports CT Ratios 100, 200, 300 & 400:5 - Ratios must be Specified with Order F0 G0 NEMA 3R Enclosure with one 8xxx Form 9S (13 Terminal) meter Installed and Wired - Dim 34 H X 25 W X 13-1/4 D NEMA 3R Enclosure with one 8xxx Form 36S (13 Terminal) meter Installed and Wired - Dim 34 H X 25 W X 13-1/4 D Meter System Type - PT s are not included, CT s are only included for enclosure types F&G A Three Phase Voltage Disconnect and Control Power 1 (1) 3-Pole Fusible Disconnect provided for meter protection - meter powered off of socket blades. (1) 3-Pole Fusible Disconnect provided for meter protection with separate (1) 1-Pole Circuit Breaker provided for 2 (65-120VAC, VDC) auxiliary control power. CT Shorting Block A 4 pole CT shorting block to accommodate 2 CT s (form 9S, 35S) B 6 pole CT shorting block to accommodate 3 CT s (form 9S, 35S, 36S) C 8 pole CT shorting block to accommodate 4 CT s (form 39S, 76S) D 10 pole Test Switch to accommodate 3 CT s & Phase Voltages (form 9S, 35S, 36S) Digital & Analog Input/Output Wiring 1 None 2 3-Form A Digital Inputs, 4 form C Relay Outputs Wired to Terminal Blocks (18 TB s total) Analog Input/Output - None Communications Wiring A B C D None COM 1 and COM 2/4 Wired to Terminal Blocks (12 TB s total) 10BaseT Ethernet equipped meter CAT5E cable will terminate directly on meter. COM 1 and COM 2/4 Wired to Terminal Blocks (12 TB s total) 10BaseFL Ethernet equipped meter CAT5E fiber cables will terminate directly on meter. COM 1 and COM 2/4 Wired to Terminal Blocks (12 TB s total) Example: Part Number 9761E8600A0A1B1C 9761E 8600 A0 A 1 B 1 C

6 2 Main/Critical Circuit PowerLogic CM4250/4000T Factory Assembled Enclosures Type 12 & 4 Description: The CM4250 and CM4000T circuit monitor enclosures are an ideal metering solution for monitoring key distribution points and sensitive loads requiring revenue accuracy and power quality analysis capabilities for critical loads. These pad-lockable, concealed hinge industrial enclosures are UL listed and are well suited for monitoring multiple services where the loads are fed from the same or separate voltage sources. CM4250 and CM4000T enclosure can monitor up to four separate sources/loads per panel utilizing one meter with remote display per load. Multiple CM4250 and CM4000T units can be networked together via Ethernet or RS-485 using Modbus communication protocol. Features Assemblies include meters and devices wired to terminal blocks, voltage disconnect(s), and current transformer (CT) shorting block(s). Available with multiple meters per panel. Serial & Ethernet Communications are options for all units. Digital and/or Analog Input/Output (I/O) are options for all units. Tailored to any meter system voltage type: 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase 240V, 480V & 600V Delta Three-Phase Supports Single or Multiple Voltage Sources for Indoor (Type 12) & Outdoor (Type 4) applications. Wall mountable and easy to install using concealed holes in the back of the enclosure. Carbon steel construction, with industry standard ANSI 61 gray powder-coat finish. Equipped with concealed hinged door, and universal pad-lockable latch. Custom engraved nameplates are available for all units. Enclosure Dimensions - see ordering information Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this equipment will be mounted on an inner swing door. The outer protective door must be opened to access door mounted equipment.

7 Ordering Information Model Order code Description Factory Assembled: Type 12 & 4 CM4250 & 4000T Meter Enclosures Main/Critical Circuit E Typical lead time is 3 - Weeks Meter Meter Type - (meter is included with enclosure) 4250 CM4250 Remote Display Meter 4000 CM4000T Remote Display Meter Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12 R1 NEMA 12 Enclosure with one meter with remote display Installed and Wired - Dim 24 H x 20 W x 10 D R2 NEMA 12 Enclosure with two meters with remote displays Installed and Wired - Dim 30 H x 24 W x 10 D R3 NEMA 12 Enclosure with three meters with remote displays Installed and Wired - Dim 36 H x 30 W x 10 D R4 NEMA 12 Enclosure with four meters with remote displays Installed and Wired - Dim 36 H x 30 W x 10 D Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4 Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required Cooling a custom design will be required. Please consult with engineering for a quote. Y1 Y2 Y3 Y4 NEMA 4 Enclosure with one meter with remote display Installed and Wired - Dim 24 H x 24 W x 12 D NEMA 4 Enclosure with two meters with remote displays Installed and Wired - Dim 30 H x 30 W x 12 D NEMA 4 Enclosure with three meters with remote displays Installed and Wired - Dim 36 H x 36 W x 12 D NEMA 4 Enclosure with four meters with remote displays Installed and Wired - Dim 42 H x 36 W x 12 D Meter System Type - PT s and CT s are not included A Three Phase - 208Y/120V WYE B Three Phase - 240V DELTA C Three Phase - 480Y/277V WYE D Three Phase - 480V DELTA E Three Phase - 600Y/347V WYE F Three Phase - 600V DELTA Voltage Disconnect and Control Power - For Options on a per enclosure basis /For Options on a per meter basis All feeders must have the same Meter System Type - Otherwise a custom quote is required Example: Part Number 9761E4000R1C2B4C 9761E 4000 R1 C 2 B 4 C (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from meter voltage inputs (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. 600/ V AC CPT provided for control power source Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter derived directly from meter voltage inputs Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure 600/ VAC CPT provided for control power source CT Shorting Block A 4 pole CT shorting block to accommodate 2 CT s per meter B 6 pole CT shorting block to accommodate 3 CT s per meter C 8 pole CT shorting block to accommodate 4 CT s per meter Digital & Analog Input/Output Wiring 1 None 2 4 DI s and 2 DO s & 1 KYZ Output and 1 AO and 1 AI wired to terminal blocks (includes default I/O + IOX DC Supply) 3 4 DI s, 3 Relay Outputs, KYZ Output and 1 DO wired to terminal blocks (Includes Default I/O + IOC44 + DC Supply) 4 DI s, 3 Relay Outputs, KYZ Output and 3 DO s, 1AO and 1 AI wired to terminal blocks 4 Includes Default I/O + IOX2411+ IOC44 + DC Supply) Communications Wiring A No communications terminal blocks included. B COM 1 wired to 5 - Two Tier TB s (5-IN, 5-OUT) One 100BaseFX, 10/100Base T equipped meter. CAT5E & Fiber cables will terminate directly on the meter. RS-485 Port wired to C terminal blocks (5-OUT) for 5 TB s total. Note: For multi meter panels each meter s comm. ports will be daisy chained together and wired to terminal blocks for both incoming and outgoing termination. Units that have Ethernet will wire exactly the same except the incoming 4-wire terminal blocks will be replaced by the meters comm. port for that network.

8 Main/Critical Circuit 3 PowerLogic ION7550/7650 Factory Assembled Enclosures Type 12 & 4 Description: The ION7550 and ION7650 metering enclosures are an ideal metering solution for monitoring key distribution points and sensitive loads requiring revenue accuracy and power quality analysis capabilities. These pad-lockable, concealed hinge industrial enclosures are UL listed and well suited for monitoring multiple services where the loads are fed from the same or separate voltage sources. ION7550/7650 enclosures contain integrated display meters capable of monitoring up to four separate sources/loads per panel utilizing one meter per load. Features Assemblies include meters & devices wired to terminal blocks, voltage disconnect(s), and current transformer (CT) shorting block(s). Available with multiple meters per panel. Serial & Ethernet Communications are options for all units Digital and/or Analog Input/Output (I/O) are options for all units. Tailored to any meter system voltage type : 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase 240V, 480V & 600V Delta Three-Phase Supports Single or Multiple Voltage Sources for Indoor (Type 12) & Outdoor (Type 4) applications. Wall mountable and easy to install using concealed holes in the back of the enclosure. Carbon steel construction, with industry standard ANSI 61 gray powder-coat finish. Custom engraved nameplates are available for all units. Enclosure Dimensions - see ordering information Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this equipment will be mounted on an inner swing door. The outer protective door must be opened to access door mounted equipment.

9 Main/Critical Circuit 3 Ordering Information 9761E Model Order code Description Meter Factory Assembled: Type 12 & 4 ION7550 & ION7650 Meter Enclosures Typical lead time is 5 - Weeks for this offering Meter Type (meter is included with enclosure) 7550 ION7550 Integrated Display Meter 7650 ION7650 Integrated Display Meter Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12 A1 NEMA 12 Enclosure with one integrated display meter Installed and Wired - Dim 20 H x 16 W x 12 D A2 NEMA 12 Enclosure with two integrated display meters Installed and Wired - Dim 24 H x 24 W x 10 D A3 NEMA 12 Enclosure with three integrated display meters Installed and Wired - Dim 30 H x 30 W x 10 D A4 NEMA 12 Enclosure with four integrated display meters Installed and Wired - Dim 36 H x 30 W x 10 D Enclosure Type and Meter Quantity - Indoor / Outdoor Applications - NEMA 4 Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required Cooling a custom design will be required. Please consult with engineering for a quote. X1 NEMA 4 Enclosure with one integrated display meter Installed and Wired - Dim 24 H x 20 W x 12 D X2 NEMA 4 Enclosure with two integrated display meters Installed and Wired - Dim 30 H x 24 W x 12 D X3 NEMA 4 Enclosure with three integrated display meters Installed and Wired - Dim 36 H x 30 W x 12 D X4 NEMA 4 Enclosure with four integrated display meters Installed and Wired - Dim 36 H x 36 W x 12 D Meter System Type - PT s and CT s are not included A Three Phase - 208Y/120V WYE B Three Phase - 240V DELTA C Three Phase - 480Y/277V WYE D Three Phase - 480V DELTA E Three Phase - 600Y/347V WYE F Three Phase - 600V DELTA Voltage Disconnect and Control Power - For Options on a per enclosure basis /For Options on a per meter basis All feeders must have the same Meter System Type - Otherwise a custom quote is required (1) 3-Pole Fusible Disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from 1 meter voltage inputs (1) 3-Pole Fusible Disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC 2 separate control power source (1) 3-Pole Fusible Disconnect provided for protection of all meters in enclosure. 600/ VAC CPT provided for control power 3 source Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter 4 derived directly from meter voltage inputs Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. (1) 1-Pole Circuit Breaker 5 provided for 120VAC separate control power source Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. 600/ VAC CPT provided 6 for control power source CT Shorting Block A 4 pole CT shorting block to accommodate 2 CT s per meter B 6 pole CT shorting block to accommodate 3 CT s per meter C 8 pole CT shorting block to accommodate 4 CT s per meter Digital & Analog Input/Output Wiring 1 None 2 8 DI s, 4 DO s and 3 Relay Outputs wired to terminal blocks (33 TB s) per meter 3 16 DI s wired to terminal blocks & 4 Al s and 4 AO s wired to terminal blocks (56 TB s) per meter 4 16 DI s, 4 DO s & 3 Relay Outputs wired to terminal blocks and 4 AI s & 4 AO s wired to terminal blocks (73 TB s) per meter Communications Wiring A No communications terminal blocks included B COM 1 and COM 2 wired to 6 terminal blocks (3-IN, 3-OUT each COM port) for 12 TB s total One 10BaseT Ethernet & 10BaseFL equipped meter. CAT5E & Fiber cables will terminate directly on meter. COM 1 and COM 2 wired to C 6 terminal clocks (3-IN, 3-OUT each COM port) for 12 TB s total Example: Part Number 9761E7650A1A1C4C 9761E 7650 A1 A 1 C 4 C Note: For multi-meter panels for each RS-485 network there will be 3 TB s for incoming COMMs to first meter and 3 TB s for outgoing COMMs off test meter. Each meter in panel will be daisy chained together.

10 Main + Multiple feeders 4 PowerLogic CM4250/4000T Main with PM820 Feeder Factory Assembled Enclosures Type 12 & 4 Description: The CM4250/4000T Main with PM820 feeder enclosure is an ideal metering solution for monitoring key distribution points and sensitive loads requiring revenue accuracy and power quality analysis capabilities. These pad-lockable enclosures are UL listed and offer an integrated solution that is well suited for monitoring the main service as well as multiple loads. These main plus feeder units allow for primary main service voltage monitoring in addition to separate voltage monitoring for the loads which share the same voltage source. Each unit is capable of monitoring up to one main service and eight separate loads per panel utilizing one meter per load. Multiple units can be networked together via Ethernet or RS-485 using Modbus communication protocol. Features Assemblies include meters & devices wired to terminal blocks, voltage disconnect(s), and 8-pole current transformer (CT) shorting block(s) on the main and 6-pole CT shorting blocks on feeders. Available with multiple meters per panel. Main meter and feeders will be wired for Inputs/Outputs. 8-Digital Inputs, 3-Relay Outs, KYZ Out, 3-Digital Outputs, 1-Analog Output, 1-Analog Input wired to terminal blocks (Includes default I/O + IOX IOC44 + DC supply). Each feeder will have 1-Digital Input, and 1-Digital Output wired to terminal blocks. (Includes Feeder default I/O only) One 100BaseFX, 10/100BaseT equipped meter. CAT5E & Fiber cabinet will terminate directly on the meter. Each meter RS-485 port will be daisy chained together, and wired to terminal blocks (5 OUT for 5 terminal blocks total). Tailored to any meter system voltage type: 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase 240V, 480V & 600V Delta Three-Phase Wall mountable and easy to install using concealed holes in the back of the enclosure. Carbon steel construction, with industry standard ANSI 61 gray powder-coat finish. Custom engraved nameplates are available for all units. Enclosure Dimensions - see ordering information Note: For Type 3R & 4 enclosures, if unit uses door mounted equipment, this equipment will be mounted on an inner swing door. The outer protective door must be opened to access door mounted equipment.

11 Main + Multiple feeders 4 Ordering Information Factory Assembled: Single Main - Multi Feeder Monitoring Panels - Type 12 & 4 CM4250 & CM4000T Main with PM820 Feeder Metering Enclosures Model Order code Description 9761M Typical lead time is 4 - Weeks This Enclosure offer utilizes remote display meters on the Main & Remote displays on the feeders Meter Meter Type (meters are included with enclosure) 4250 CM4250 Circuit Monitor with CMDVF & CMDGN12, IOX2411, IOC44 and ECC CM4000T Circuit Monitor with CMDVF & CMDGN12, IOX2411, IOC44 and ECC21 F82 PM820 Remote Display Meter. One per feeder Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12 R1 NEMA 12 Enclosure with one Main and one Feeder meter Installed and Wired - Dim 24 H x 24 W x 10 D R2 NEMA 12 Enclosure with one Main and two Feeder meters Installed and Wired - Dim 30 H x 24 W x 10 D R3 NEMA 12 Enclosure with one Main and three Feeder meters Installed and Wired - Dim 30 H x 24 W x 10 D R4 NEMA 12 Enclosure with one Main and four Feeder meters Installed and Wired - Dim 30 H x 30 W x 10 D R5 NEMA 12 Enclosure with one Main and five Feeder meters Installed and Wired - Dim 30 H x 30 W x 10 D R6 NEMA 12 Enclosure with one Main and six Feeder meters Installed and Wired - Dim 36 H x 30 W x 10 D R7 NEMA 12 Enclosure with one Main and seven Feeder meters Installed and Wired - Dim 36 H x 30 W x 10 D R8 NEMA 12 Enclosure with one Main and eight Feeder meters Installed and Wired - Dim 36 H x 30 W x 10 D Enclosure Type and Meter Quantity - Indoor/Outdoor - NEMA 4 Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required Cooling a custom design will be required. Please consult with engineering for a quote. Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Example: Part Number 9671E4000F82R3A2 9761M 4000 F82 R3 A 2 NEMA 4 Enclosure with one Main and one Feeder meter Installed and Wired - Dim 30 H x 24 W x 12 D NEMA 4 Enclosure with one Main and two Feeder meters Installed and Wired - Dim 30 H x 24 W x 12 D NEMA 4 Enclosure with one Main and three Feeder meters Installed and Wired - Dim 30 H x 30 W x 12 D NEMA 4 Enclosure with one Main and four Feeder meters Installed and Wired - Dim 30 H x 30 W x 12 D NEMA 4 Enclosure with one Main and five Feeder meters Installed and Wired - Dim 36 H x 30 W x 12 D NEMA 4 Enclosure with one Main and six Feeder meters Installed and Wired - Dim 36 H x 30 W x 12 D NEMA 4 Enclosure with one Main and seven Feeder meters Installed and Wired - Dim 36 H x 30 W x 12 D NEMA 4 Enclosure with one Main and eight Feeder meters Installed and Wired - Dim 36 H x 36 W x 12 D Meter System Type - PT s and CT s are not included A Three Phase - 208Y/120V WYE B Three Phase - 240V DELTA C Three Phase - 480Y/277V WYE D Three Phase - 480V DELTA E Three Phase - 600Y/347V WYE F Three Phase - 600V DELTA Voltage Disconnect and Control Power (2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. Control power for 1 meter derived directly from meter voltage inputs 2 3 (2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source for all meters (2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. 600/ VAC CPT provided for control power source derived from Main meter voltage inputs

12 Main + Multiple feeders 5 PowerLogic ION7550/7650 Main with ION6200 Feeder Factory Assembled Enclosures Type 12 & 4 Description: The ION75/7650 Main with ION6200 Feeder enclosure is an ideal metering solution for monitoring key distribution points and sensitive loads requiring revenue accuracy and power quality analysis capabilities. These pad-lockable enclosures are UL listed and offer an integrated solution that is well suited for monitoring the main service as well as multiple loads. These main plus feeder units allow for primary main service voltage monitoring in addition to separate voltage monitoring for the loads which share the same voltage source. Each unit is capable of monitoring up to one main service and eight separate loads per panel utilizing one meter per load. Multiple units can be networked together via Ethernet or RS-485 using Modbus, ION or other industry standard communication protocols. Features Assemblies include meters & devices wired to terminal blocks, voltage disconnect(s), and 8-pole current transformer (CT) shorting block on main and 6-pole CT shorting blocks on feeders. Available with multiple meters per panel. Main meter will be wired for Inputs/Outputs, feeders will not. 16 Digital Inputs, 4 Digital Outputs, and 3 Relay OUtputs wired to terminal blocks and 4 Analog Inputs and 4 Analog Outputs wired to terminal blocks. One 10 Base-T Ethernet and 10 Base-FL equipped meter. CAT 5E and fiber cables will terminate directly on meter. Each RS-485 port will be daisy chained together and wired to terminal blocks. Tailored to any meter system voltage type: 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase 240V, 480V & 600V Delta Three-Phase Wall mountable and easy to install using concealed holes in the back of the enclosure. Carbon steel construction, with industry standard ANSI 61 gray powder-coat finish. Custom engraved nameplates are available for all units. Enclosure Dimensions - see ordering information Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this equipment will be mounted on an inner swing door. The outer protective door must be opened to access door mounted equipment.

13 Ordering Information Main + Multiple feeders 5 Factory Assembled: Single Main - Multi Feeder Monitoring Panels - Type 12 & 4 ION7550 & ION7650 Main with ION6200 Feeder Metering Enclosures Model Order code Description 9761M Typical lead time is 6 - Weeks This Enclosure offer utilizes integrated display meters on the Main & Remote displays on the feeders Meter Meter Type (meters are included with enclosure) 7550 ION7550 Integrated Display Meter with expanded communications and I/O (Ethernet 10BaseT, 10BaseFL) 7650 ION7650 Integrated Display Meter with expanded communications and I/O (Ethernet 10BaseT, 10BaseFL) F62 ION6200 Remote Display Meter. One per feeder Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12 R1 NEMA 12 Enclosure with one Main and one Feeder meter Installed and Wired - Dim 24 H x 24 W x 10 D R2 NEMA 12 Enclosure with one Main and two Feeder meters Installed and Wired - Dim 30 H x 24 W x 10 D R3 NEMA 12 Enclosure with one Main and three Feeder meters Installed and Wired - Dim 30 H x 24 W x 10 D R4 NEMA 12 Enclosure with one Main and four Feeder meters Installed and Wired - Dim 30 H x 30 W x 10 D R5 NEMA 12 Enclosure with one Main and five Feeder meters Installed and Wired - Dim 30 H x 30 W x 10 D R6 NEMA 12 Enclosure with one Main and six Feeder meters Installed and Wired - Dim 36 H x 30 W x 10 D R7 NEMA 12 Enclosure with one Main and seven Feeder meters Installed and Wired - Dim 36 H x 30 W x 10 D R8 NEMA 12 Enclosure with one Main and eight Feeder meters Installed and Wired - Dim 36 H x 30 W x 10 D Enclosure Type and Meter Quantity - Indoor / Outdoor Applications - NEMA 4 Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required Cooling a custom design will be required. Please consult with engineering for a quote. Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Example: Part Number 9761M7650F62R8C2 9761M 7650 F62 R8 C 2 NEMA 4 Enclosure with one Main and one Feeder meter Installed and Wired - Dim 30 H x 24 W x 12 D NEMA 4 Enclosure with one Main and two Feeder meters Installed and Wired - Dim 30 H x 24 W x 12 D NEMA 4 Enclosure with one Main and three Feeder meters Installed and Wired - Dim 30 H x 30 W x 12 D NEMA 4 Enclosure with one Main and four Feeder meters Installed and Wired - Dim 30 H x 30 W x 12 D NEMA 4 Enclosure with one Main and five Feeder meters Installed and Wired - Dim 36 H x 30 W x 12 D NEMA 4 Enclosure with one Main and six Feeder meters Installed and Wired - Dim 36 H x 30 W x 12 D NEMA 4 Enclosure with one Main and seven Feeder meters Installed and Wired - Dim 36 H x 30 W x 12 D NEMA 4 Enclosure with one Main and eight Feeder meters Installed and Wired - Dim 36 H x 36 W x 12 D Meter System Type - PT s and CT s are not included A Three Phase - 208Y/120V WYE B Three Phase - 240V DELTA C Three Phase - 480Y/277V WYE D Three Phase - 480V DELTA E Three Phase - 600Y/347V WYE F Three Phase - 600V DELTA Voltage Disconnect and Control Power - For options on a per enclosure basis All feeders must have the same Meter System Type - Otherwise a custom quote is required (2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. Control power for 1 meter derived directly from meter voltage inputs 2 3 (2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source for all meters (2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. 600/ VAC CPT provided for control power source derived from Main meter voltage inputs

14 Secondary Mains 6 PowerLogic CM3000 Series Factory Assembled Enclosures Type 12 & 4 Description: The CM3250 and CM3350 enclosures are an ideal metering solution for monitoring key distribution points and sensitive loads requiring both revenue accuracy and power quality analysis capabilities. These pad-lockable enclosures are UL listed and well suited for monitoring multiple services where the loads are fed from the same or separate voltage source(s). CM3250 and CM3350 enclosures with remote display meters are capable of monitoring four separate sources/loads per panel utilizing one meter per load. Multiple CM3250 and CM3350 units can be networked together via Ethernet or RS-485 using Modbus communications protocol. Features Assemblies include meters & devices wired to terminal blocks, voltage disconnect(s), and current transformer (CT) shorting block(s). Available with multiple meters per panel. Serial & Ethernet Communications are options for all units. Digital and/or Analog Input/Output (I/O) are options for all units. Tailored to any meter system voltage type: 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase 240V, 480V & 600V Delta Three-Phase Supports Single or Multiple Voltage Sources for Indoor (Type 12) & Outdoor (Type 4) applications. Wall mountable and easy to install using concealed holes in the back of the enclosure. Carbon steel construction, with industry standard ANSI 61 gray powder-coat finish. Custom engraved nameplates are available for all units. Enclosure Dimensions - see ordering information Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this equipment will be mounted on an inner swing door. The outer protective door must be opened to access door mounted equipment.

15 Ordering Information Model Order code Description Factory Assembled: Type 12 & 4 CM3250 & CM3350 Meter Enclosures Secondary Mains E Typical lead time is 3 - Weeks Nameplates Available Upon Request (Provide Nameplate Schedule With Order) Meter Meter Type (meter is included with enclosure) 3250 CM3250 Remote Display Meter 3350 CM3350 Remote Display Meter Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12 R1 NEMA 12 Enclosure with one meter with remote display Installed and Wired - Dim 24 H x 20 W x 10 D R2 NEMA 12 Enclosure with two meters with remote displays Installed and Wired - Dim 30 H x 24 W x 10 D R3 NEMA 12 Enclosure with three meters with remote displays Installed and Wired - Dim 30 H x 30 W x 10 D R4 NEMA 12 Enclosure with four meters with remote displays Installed and Wired - Dim 36 H x 30 W x 10 D Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4 Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required Cooling a custom design will be required. Please consult with engineering for a quote. Y1 Y2 Y3 Y4 NEMA 4 Enclosure with one meter with remote display Installed and Wired - Dim 24 H X 24 W X 12 D NEMA 4 Enclosure with two meters with remote displays Installed and Wired - Dim 30 H X 30 W X 12 D NEMA 4 Enclosure with three meters with remote displays Installed and Wired - Dim 36 H X 30 W X 12 D NEMA 4 Enclosure with four meters with remote displays Installed and Wired - Dim 36 H X 36 W X 12 D Meter System Type - PT s and CT s are not included A Three Phase - 208Y/120V WYE B Three Phase - 240V DELTA C Three Phase - 480Y/277V WYE D Three Phase - 480V DELTA E Three Phase - 600Y/347V WYE F Three Phase - 600V DELTA Voltage Disconnect and Control Power - For Options on a per enclosure basis /For Options on a per meter basis All feeders must have the same Meter System Type - Otherwise a custom quote is required Example: Part Number 9761E3350Y1A2B1C 9761E 3350 Y1 A 2 B 1 C (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from meter voltage inputs (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. 600/ V AC CPT provided for control power source Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter derived directly from meter voltage inputs Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure 600/ VAC CPT provided for control power source CT Shorting Block A 4 pole CT shorting block to accommodate 2 CT s per meter B 6 pole CT shorting block to accommodate 3 CT s per meter C 8 pole CT shorting block to accommodate 4 CT s per meter Digital & Analog Input/Output Wiring - Option 2 not available with Comm. Option C 1 None 2 4 DI s, 3 Relay Outputs, KYZ Output and 1 DO wired to terminal blocks (Includes Default I/O + IOC44 + DC Supply) per meter Communications Wiring A No communications terminal blocks included. B COM 1 wired to 5 - Two Tier TB s (5-IN, 5-OUT) One 100BaseFX, 10/100BaseT equipped meter. CAT5E & Fiber cables will terminate directly on the meter. RS-485 Port wired C to terminal blocks (5-OUT) for 5 TB s total. Note: For multi meter panels each meter s comm. ports will be daisy chained together and wired to terminal blocks for both incoming and outgoing termination. Units that have Ethernet will wire exactly the same except the incoming 4-wire terminal blocks will be replaced by the meters comm. port for that network.

16 Secondary Mains 7 PowerLogic ION7300 Series Factory Assembled Enclosures Type 12 & 4 Description: The ION7300 series enclosures are and ideal metering solution for high accuracy feeder monitoring and secondary mains. These pad-lockable enclosures are UL listed and well suited for monitoring multiple loads fed from the same or separate voltage sources. ION7300 series enclosures are capable of monitoring up to four separate sources/loads per panel utilizing one remote display or integrated display meter per load. Multiple ION7300 series units can be networked together via Ethernet or RS-485 using Modbus, ION or other industry standard communication protocols. Features Assemblies include meters & devices wired to terminal blocks, voltage disconnect(s), and current transformer (CT) shorting block(s). Available with multiple meters per panel. Serial & Ethernet Communications are options for all units. Digital and/or Analog Input/Output (I/O) are options for all units. Tailored to any meter system voltage type: 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase 240V, 480V & 600V Delta Three-Phase Wall mountable and easy to install using concealed holes in the back of the enclosure. Carbon steel construction, with industry standard ANSI 61 gray powder coat finish. Custom engraved nameplates are available for all units. Enclosure Dimensions - see ordering information Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this equipment will be mounted on an inner swing door. The outer protective door must be opened to access door mounted equipment.

17 Ordering Information 9761E Model Order code Description Meter Factory Assembled: Type 12 & 4 ION7300, ION7330 & ION7350 Meter Enclosures Typical lead time is 6 - Weeks Meter Type - (meter is included with enclosure) 7300 ION7300 Remote or Integrated Display Meter 7330 ION7330 Remote or Integrated Display Meter 7350 ION7350 Remote or Integrated Display Meter Secondary Mains Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12 A1 NEMA 12 Enclosure with one meter with integrated display Installed and Wired - Dim 20 H x 16 W x 12 D A2 NEMA 12 Enclosure with two meters with integrated displays Installed and Wired - Dim 20 H x 20 W x 12 D A3 NEMA 12 Enclosure with three meters with integrated displays Installed and Wired - Dim 24 H x 20 W x 10 D A4 NEMA 12 Enclosure with four meters with integrated displays Installed and Wired - Dim 24 H x 24 W x 10 D R1 NEMA 12 Enclosure with one meter with remote display Installed and Wired - Dim 20 H x 16 W x 12 D R2 NEMA 12 Enclosure with two meters with remote displays Installed and Wired - Dim 24 H x 20 W x 10 D R3 NEMA 12 Enclosure with three meters with remote displays Installed and Wired - Dim 24 H x 24 W x 10 D R4 NEMA 12 Enclosure with four meters with remote displays Installed and Wired - Dim 30 H x 24 W x 10 D Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4 Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required Cooling a custom design will be required. Please consult with engineering for a quote. X1 NEMA 4 Enclosure with one meter with integrated display Installed and Wired - Dim 20 H x 20 W x 12 D X2 NEMA 4 Enclosure with two meters with integrated displays Installed and Wired - Dim 24 H x 20 W x 12 D X3 NEMA 4 Enclosure with three meters with integrated displays Installed and Wired - Dim 24 H x 24 W x 10 D X4 NEMA 4 Enclosure with four meters with integrated displays Installed and Wired - Dim 30 H x 24 W x 10 D Y1 NEMA 4 Enclosure with one meter with remote display Installed and Wired - Dim 20 H x 20 W x 12 D Y2 NEMA 4 Enclosure with two meters with remote displays Installed and Wired - Dim 24 H x 24 W x 12 D Y3 NEMA 4 Enclosure with three meters with remote displays Installed and Wired - Dim 30 H x 24 W x 12 D Y4 NEMA 4 Enclosure with four meters with remote displays Installed and Wired - Dim 30 H x 30 W x 12 D Meter System Type - PT s and CT s are not included A Three Phase - 208Y/120V WYE B Three Phase - 240V DELTA C Three Phase - 480Y/277V WYE D Three Phase - 480V DELTA E Three Phase - 600Y/347V WYE F Three Phase - 600V DELTA Voltage Disconnect and Control Power For Options on a per enclosure basis /For Options on a per meter basis All feeders must have the same Meter System Type - Otherwise a custom quote is required 1 (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from meter voltage inputs 2 (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source 3 (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. 600/ V AC CPT provided for control power source 4 Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter derived directly from meter voltage inputs 5 Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source. 6 Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure 600/ VAC CPT provided for control power source CT Shorting Block A 4 pole CT shorting block to accommodate 2 CT s per meter B 6 pole CT shorting block to accommodate 3 CT s per meter Digital & Analog Input/Output Wiring (Available on integrated display meters only. A and X Enclosure Types) 1 None 2 4 DI s and 4 DO s wired to terminal blocks (16 TB s) per Meter 3 4 AI s and 4 AO s wired to terminal blocks (24 TB s) per Meter 4 4 DI s and 4 DO s wired to terminal blocks & 4 AI s and 4 AO s wired to terminal blocks (40 TB s) per meter Communications Wiring A No communications terminal blocks included. B COM 1 and COM 2 wired to 6 terminal blocks (3-IN, 3-OUT each COM port) for 12 TB s total C One Ethernet equipped meter. CAT5E cable will terminate directly on meter. COM 1 and COM 2 wired to 6 terminal blocks (3-IN, 3-OUT each COM port) for 12 TB s total Note: For multi meter panels each meter s comm. ports will be daisy chained together and wired to terminal blocks for both incoming and outgoing termination. Units that have Ethernet will wire exactly the same except the incoming 2-wire terminal blocks will be replaced by the meters comm. port for that network. Example: Part Number 9761E7350R1C3B1C 9761E 7350 R1 C 3 B 1 C 7

18 Feeders 8 PowerLogic ION6200 Factory Assembled Enclosures Type 12 & 4 Description: The ION6200 enclosures are an ideal metering solution for high accuracy feeder monitoring and submetering. These pad-lockable enclosures are UL listed and well suited for monitoring multiple services where the loads are fed from the same or separate voltage sources. ION6200 enclosures are capable of monitoring up to four separate sources/loads per panel utilizing one meter with remote display per load. Multiple ION6200 units can be networked together via Ethernet or RS-485 using Modbus, ION or other industry standard communication protocols. Feautures Assemblies include meters & devices wired to terminal blocks, voltage disconnect(s), and current transformer (CT) shorting block(s). Available with multiple meters per panel. Serial & Ethernet Communications are options for all units. Digital and/or Analog Input/Output (I/O) are options for all units. Tailored to any meter system voltage type: 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase 240V, 480V & 600V Delta Three-Phase Supports Single or Multiple Voltage Sources for Indoor (Type 12) & Outdoor (Type 4) applications. Wall mountable and easy to install using concealed holes in the back of the enclosure. Carbon steel construction, with industry standard ANSI 61 gray powder-coat finish. Custom engraved nameplates are available for all units. Enclosure Dimensions - see ordering information Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this equipment will be mounted on an inner swing door. The outer protective door must be opened to access door mounted equipment.

19 Feeders 8 Ordering Information Factory Assembled: Type 12 & 4 ION6200 Meter Enclosures Model Order code Description 9761E Typical lead time is 3 - Weeks Meter Meter Type (meter is included with enclosure) 6200 ION6200 Remote Display Meter Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12 R1 NEMA 12 Enclosure with one meter with remote display Installed and Wired - Dim 20 H x 16 W x 8 D R2 NEMA 12 Enclosure with two meters with remote displays Installed and Wired - Dim 24 H x 20 W x 8 D R3 NEMA 12 Enclosure with three meters with remote displays Installed and Wired - Dim 24 H x 24 W x 8 D R4 NEMA 12 Enclosure with four meters with remote displays Installed and Wired - Dim 30 H x 24 W x 8 D Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4 Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required Cooling a custom design will be required. Please consult with engineering for a quote. Y1 Y2 Y3 Y4 NEMA 4 Enclosure with one meter with remote display Installed and Wired - Dim 24 H x 20 W x 10 D NEMA 4 Enclosure with two meters with remote displays Installed and Wired - Dim 30 H x 24 W x 10 D NEMA 4 Enclosure with three meters with remote displays Installed and Wired - Dim 30 H x 30 W x 10 D NEMA 4 Enclosure with four meters with remote displays Installed and Wired - Dim 36 H x 30 W x 10 D Meter System Type - PT s and CT s are not included A Three Phase - 208Y/120V WYE B Three Phase - 240V DELTA C Three Phase - 480Y/277V WYE D Three Phase - 480V DELTA E Three Phase - 600Y/347V WYE F Three Phase - 600V DELTA Voltage Disconnect and Control Power - For Options on a per enclosure basis /For Options on a per meter basis All feeders must have the same Meter System Type - Otherwise a custom quote is required (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from 1 meter voltage inputs Example: Part Number: 9761E6200R1A2B1B 9761E 6200 R1 A 2 B 1 B (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. 600/ V AC CPT provided for control power source Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter derived directly from meter voltage inputs Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source. Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure 600/ VAC CPT provided for control power source CT Shorting Block A 4 pole CT shorting block to accommodate 2 CT s per meter B 6 pole CT shorting block to accommodate 3 CT s per meter Digital & Analog Input/Output Wiring (Available on integrated display meters only. A and X Enclosure Types) 1 None 2 2 DO s wired to terminal blocks (2 TB s) per Meter. Analog I/O - None Communications Wiring A No communications terminal blocks included B COM 1 wired to 6 terminal blocks (3-IN, 3-OUT) C EGX100 with power supply wired to Com1 and terminal blocks (3-out) modbus protocol only. Note: For multi meter panels each meter s comm. ports will be daisy chained together and wired to terminal blocks for both incoming and outgoing termination. Units that have Ethernet will wire exactly the same except the incoming 2-wire terminal blocks will be replaced by the meters comm. port for that network.

20 Feeders 9 PowerLogic PM800 Series Factory Assembled Enclosures Type 12 & 4 Description: The PM800 series enclosures are an ideal metering solution for high accuracy feeder monitoring and submetering. These pad-lockable enclosures are UL listed and well suited for monitoring multiple loads fed from the same or separate voltage sources. PM800 series enclosures are capable of monitoring up to four separate sources/loads per panel utilizing one remote display meter per load. Multiple PM800 series units can be networked together via Ethernet or RS-485 using Modbus communication protocol. Features Assemblies include meters & devices wired to terminal blocks, voltage disconnect(s) and current transformer (CT) shorting block(s). Available with multiple meters per panel. Serial & Ethernet Communications are options for all units. Digital and/or Analog Input/Output (I/O) are options for all units. Tailored to any meter system voltage type: 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase 240V, 480V & 600V Delta Three-Phase Supports Single or Multiple Voltage Sources for Indoor (Type 12) & Outdoor (Type 4) applications Wall mountable and easy to install using concealed holes in the back of the enclosure. Carbon steel construction, with industry standard ANSI 61 gray powder-coat finish. Custom engraved nameplates are available for all units. Enclosure Dimensions - see ordering information Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this equipment will be mounted on an inner swing door. The outer protective door must be opened to access door mounted equipment.

21 Ordering Information 9761E Model Order code Description Factory Assembled: Type 12 & 4 PM810, PM820, PM850 & PM870 Meter Enclosures Typical lead time is 3 - Weeks Nameplates Available Upon Request (Provide Nameplate Schedule With Order) Meter Meter Type (meter is included with enclosure) 0810 PM810 Remote Display Meter 0820 PM820 Remote Display Meter 0850 PM850 Remote Display Meter 0870 PM870 Remote Display Meter Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12 R1 NEMA 12 Enclosure with one meter with remote display Installed and Wired - Dim 20 H x 16 W x 8 D R2 NEMA 12 Enclosure with two meters with remote displays Installed and Wired - Dim 24 H x 20 W x 8 D R3 NEMA 12 Enclosure with three meters with remote displays Installed and Wired - Dim 24 H x 24 W x 8 D R4 NEMA 12 Enclosure with four meters with remote displays Installed and Wired - Dim 30 H x 24 W x 8 D Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4 Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required Cooling a custom design will be required. Please consult with engineering for a quote.e. Y1 Y2 Y3 Y4 NEMA 4 Enclosure with one meter with remote display Installed and Wired - Dim 24 H x 20 W x 10 D NEMA 4 Enclosure with two meters with remote displays Installed and Wired - Dim 30 H x 24 W x 10 D NEMA 4 Enclosure with three meters with remote displays Installed and Wired - Dim 30 H x 30 W x 10 D NEMA 4 Enclosure with four meters with remote displays Installed and Wired - Dim 36 H x 30 W x 10 D Meter System Type - PT s and CT s are not included A Three Phase - 208Y/120V WYE B Three Phase - 240V DELTA C Three Phase - 480Y/277V WYE D Three Phase - 480V DELTA E Three Phase - 600Y/347V WYE F Three Phase - 600V DELTA Voltage Disconnect and Control Power - For Options on a per enclosure basis /For Options on a per meter basis All feeders must have the same Meter System Type - Otherwise a custom quote is required (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from 1 meter voltage inputs Example: Part Number 9761E0820R1C3B5C 9761E 0820 R1 C 3 B 5 C (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source (1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. 600/ V AC CPT provided for control power source Feeders Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter derived directly from meter voltage inputs Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure (1) 1-Pole Circuit Breaker provided for 120VAC separate control power source Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure 600/ VAC CPT provided for control power source CT Shorting Block A 4 pole CT shorting block to accommodate 2 CT s per meter B 6 pole CT shorting block to accommodate 3 CT s per meter Digital & Analog Input/Output Wiring 1 None (No I/O Wiring Provided) 2 1 DI and 1 DO wired to terminal blocks (2 TB s) (Default I/O + DC Supply) per meter 3 3 DI s and 3 DO s wired to terminal blocks (6 TB s) (Includes default I/O + PM8M22 + DC Supply) per meter 4 7 DI s and 3 DO s wired to terminal blocks (10 TB s) (Includes default I/O + PM8M22) per meter 2 AI s and 2 AO s wired to terminal blocks & 3 DI s and 3 DO s wired to terminal blocks (14 TB s) 5 Includes Default I/O + PM8M22 + DC Supply) per meter Communications Wiring A B C No communications terminal blocks included Both RS-485 ports wired to TB s 2-Wire port wired to 3-Two Tier TB s (3-IN, 3-OUT) & 4-Wire port wired to 5-Two-Tier TB s (5-IN, 5-OUT) One Ethernet equipped meter. CAT5E cable will terminate directly on meter. 4-Wire port will be wired to terminal blocks (5-OUT) Note: For multi meter panels each meter s comm. ports will be daisy chained together and wired to terminal blocks for both incoming and outgoing termination. Units that have Ethernet will wire exactly the same except the incoming 4-wire terminal blocks will be replaced by the meters comm. port for that network. 9