Best MATERIALS.com WEATHER GARD TM. Discount Warehouse. Product Guide

Transcription

1 WEATHER GARD TM Product Guide Best MATERIALS.com Discount Warehouse

2

3 Table of Contents Section Page Section Page General Information Fastener Design Washer and Fastener Head Styles... 5 Structural Performance... 6 Self-Drilling Fasteners Impax Performance Drill Screws... 7 Impax Heavy Metal Thickness Structural Drill Screws... 8 Impax Sealer Drill Screws... 9 Impax 1/4" Drill Screws Impax Utility Self-Drill Stainless Flat Head Utility Self-Drill Alloy Capped Fasteners ZAC Impax 5/16" HWH Alloy Capped ZAC Impax 3/8" HWH Alloy Capped (for metal to metal) ZAC Impax 3/8" HWH Alloy Capped (for metal to metal and insulated panel to metal) MAC Impax Stainless Capped Self-Drill ZAC Self-Tapping Fasteners Prisma Self-Tapping Fasteners Carbon Steel Type A, AB, B Stainless Steel Type A, AB, B Architectural Fasteners (304SS Fasteners) SX Stainless Self-Drill irius SX Stainless Self-Drill SX TORX Self-Drill TW-S Stainless Self-Tapping (cladding fastener) SLA Stainless Self-Drill (Aluminum composite to aluminum) SA6/TDA (Panel fabrication fasteners) AP Rivet (Cladding panels to aluminum or steel) TU-S Blind Fastener (HPL cladding panel attachment) GAZ Design Elements Metal to Wood Woodgrip Fasteners EVERGRIP Stainless Fasteners...41 Stainless Aluminum Panel Woodgrip Woodgrip Capped Fasteners Panelmaster Metal to Wood Fastening System Panelmaster Tool & Collated Belted Fasteners Standing Seam Roof Attachment Standing Seam Panel Clips Bearing Plates Clip Fasteners Attachment Solutions AceClamp - for Standing Seam Roofs SOL-R - solar attachment for exposed fastener metal roofs Blind Rivets and Grommets Blind Rivets Blind Rivet Tools Grommet Fasteners Closure, Sealants, Flashings and Venting Products WG-7 Closure Pipe Flashing ProfileVent Ventco Ridge Cap Anchor Clip Butyl Tape Hannoband BG1 Joint Sealant Tape Novaflex Metal Roof Sealant Tools and Tool Accessories Installation Screw Guns and drive sockets...74 Panelmaster Tool Kit Blind Rivet Tools

4 There's More to See... The fasteners shown are standard products. Many related, non-standard items are not shown, but are available and will be priced on application. We offer a complete selection of fasteners, closures and accessories. Please contact us with specific requirements. A Word About the Specification of Fasteners Proper fastener selection takes into account where and how the fasteners are installed. Factors that must be considered include: materials being attached, environmental factors, installation conditions, and safety issues. Because product specifications, applications, and interpretations may differ, specifiers and purchasers must make their own product evaluation to be assured of suitability for the intended use. Disclosure Statement Fastener data shown herein is subject to change or correction for typographical error without notice. All test data and ultimate values shown in this catalog are the result of laboratory testing. Specific job conditions should be considered and appropriate safety factors applied when specifying fasteners. In actual applications, proper installation techniques must be used to assure adequate performance of the fastener. Assistance and recommendations are available by contacting your SFS intec, Inc. sales or customer service professional. Final selection of fasteners or accessories for use is ultimately the decision of the purchaser. While SFS intec, Inc. may assist by providing data and information for comparison, it makes no suggestions or warranties pertaining to the suitability of its products for any particular applicaion. Galvalume is a registered trademark of BIEC International, Inc. TORX is a registered trademark of Textron Inc.

5 Fastener Design Fastener Design Threaded fasteners for roofing and siding systems are available in a wide range of materials, designs, and coatings. When specifying your fastener, be sure to choose one that has a performance life equaling or exceeding the life of the proposed project. Fastener Materials Common Fastener compositions: Zinc plated and paint coated carbon steel Alloy capped fasteners with zinc-aluminum, stainless steel, and nylon capped head designs Stainless Steel: 300 Series austenitic stainless steel Stainless Steel: 400 Series martensitic stainless steel Bi-metal: stainless head and threaded shank with a joint welded hardened carbon steel drill or sharp point Coated Corrosion-Resistant Fasteners SFS intec offers various coating systems such as electroplating, mechanical plating, and VistaCoat Premium System. Zinc serves as a sacrificial coating to provide cut-edge plating protection. Metal Alloy Capped Fasteners ZAC design fasteners are available with a 5/16" and 3/8" capped hex washer head in Impax self-drilling fasteners, Woodgrip sheet-to-wood fasteners and self-tapping screws. MAC 300 Series Stainless Capped Head Self-Drilling Fasteners MAC 300 Series Stainless capped head design combines the corrosion resistance of stainless steel and a hardened steel fastener for self-drilling installation. MAC fasteners are available with a 5/16" capped hex washer head in Impax self-drilling fasteners and with a 1/4" hex washer head in Woodgrip fasteners. Prisma Nylon Head Self-Drilling and Self-Tapping Fasteners ZAC Zinc Aluminum Capped Head ZAC design fasteners provide the corrosion resistance of a zinc-aluminum alloy capped head on a hardened steel fastener for self-drilling or self-tapping installation. ZAC is the original capped zinc-aluminum head fastener and is used in more metal buildings than any other capped fastener. Prisma design fasteners combine the corrosion resistance of a nylon-molded head with a hardened steel fastener for self-drilling and self-tapping installation. The nylon head is formulated with the color built in. It naturally resists fading and will never rust like steel headed fasteners. Prisma design fasteners are available with 3/8" and 7/16" hex washer heads in selfdrillers, Woodgrip metal-to-wood fasteners, and selftapping AB fasteners.

6 Fastener Design Stainless Steel Fasteners A commonly held belief that stainless steel will not rust or corrode is not necessarily accurate. Stainless steel is a generic term covering over 200 different types of alloys that, to varying degrees, corrode less than carbon steel. It is important that a specifier be aware of the panel and project performance expectations when specifying stainless steel fasteners. Several types of stainless steel are used for fasteners. 300 Series Stainless/Austenitic 18-8 stainless alloy with 18% chromium and 8% nickel Best known grades are 304 and 316, both work hardened in the thread-rolling process to manufacture a self-tapping fastener capable of tapping threads into steel Can be manufactured as a self-drilling, bi-metal fastener by incorporating a heat-treated hardened carbon steel drill point joint welded to the austenitic stainless fastener Nonmagnetic Provides excellent corrosion resistance compared to martensitic 410SS fasteners and plated steel fasteners Austenitic stainless steel is considered the only type of stainless steel for panel fasteners 410 Series Stainless/Martensitic Stainless alloy with 11.5% to 13.5% chromium Can be heat treated to provide hardness to manu facture as self-tapping or self-drilling fasteners (when hardened, the part has less corrosion resistance) Poor corrosion resistance compared to austenitic stainless Magnetic Plated to improve corrosion resistance (like carbon steel fasteners) Martensitic stainless is not considered suitable for panel fasteners Bi-Metal Fasteners SX Fastener: Austenitic Stainless Self-Drilling Fasteners SX design fasteners combine the corrosion resistance of an austenitic 300 series stainless head and threaded shank with a hardened carbon steel point for selfdrilling installation. These bi-metal fasteners install like carbon steel fasteners and provide the corrosion resistance of series austenitic stainless. SX fasteners are true stainless steel self-drilling fasteners. When selecting a stainless steel fastener for any application where minimizing or virtually eliminating corrosion is the goal, a specifier should strongly consider the dramatically greater benefits of 300 series over 400 series stainless steel fasteners. The richer chemical composition and SX welded drill point make 300 series stainless steel fasteners more costly, but the corrosion resistance benefits are far superior.

7 Washer Styles Washer Styles Washer design contributes to the weather seal of a fastener. SFS offers several washer options based upon the type of fastener and the application requirements. Control Seal Bonded Washer EPDM rubber bonded to metal Metal washers are available in galvanized steel, aluminum, and stainless steel Bonded washers offer a low-profile appearance Provides positive weather seal between panel and fastener head Sealer Cupped Hex Washer Head EPDM rubber captured under integral cupped hex head washer Cupped washer head prevents overdriving EPDM washer and cupped head offers an excellent weather seal EPDM is protected from UV rays by cupped washer head EPDM rubber captured under the stamped dome Available on all #9 and #12 XG Woodgrip drill screws Reinforced domed shoulder distributes clamp load EPDM sealant compressed in three key areas Weather tight seal even if fastener is driven in on an angle* Fastener Head Styles SFS offers a wide variety of fastener head styles designed to meet your project and fastener requirements. Each head style will provide proper panel attachment and desired finish appearance. Available fastener head styles are: irius drive, low profile HWH (hex washer head) Cupped hex washer head sealer Metal-alloy capped cupped: HWH ZAC or HWH MAC Pancake head Low Profile TORX Low Profile Wafer Head *Proper installation techniques should always be employed. NEGATIVE reduced 00% File Name: FD00.5_ZAC_HeadStyle.eps Created by: EWB-12/10/02

8 Structural Performance Structural Performance Fastener and steel gauge sizes used throughout this Weather Gard section are nominal. Fastener Sizes Fastener Size #8 #9 #10 #12 #14 #17 Thread Diameter Decimal Equivalent Steel Gauge Sizes * Gauge Decimal Equivalent * Standard steel thickness used for panels, purlins and girts. Fasteners are designed to withstand a varied range of types of loading. Each panel or structural system has its own specific fastener loading requirements. Care must be taken to ensure that the appropriate loading requirements for each application are considered. Typical structural performance criteria that influence fastener design include: Ultimate Tension Strength The point at which a fastener fails under a load exerted in two direct opposite directions. Typical ultimate tension strengths of each fastener type are provided on the fastener information pages. Ultimate Torsion Strength The point at which a fastener fails under a twisting load exerted on the head during installation in a torsional direction. Typical ultimate torsion strengths of each fastener type are provided on the fastener information pages. Ultimate Shear Strength The point at which a fastener fails under a load exerted in offset opposing directions, usually upon the shank of the fastener. Typical ultimate shear strengths of each fastener type are provided on the fastener information pages. Pull-out Performance The ability of a fastener s threaded connection to remain intact and resist tensile loads. Self-tapping fasteners require that a pilot hole be drilled prior to installation. The pullout resistance will be directly related to the pilot hole diameter. Self-drilling fasteners have been developed, and are available, for most steel construction applications, to a metal thickness of 1/2". This type of fastener is manufactured with its own integral drill point, which is engineered to drill the optimum hole size to facilitate efficient thread forming in the metal structure, resulting in optimized pullout values. Pull-over Performance The ability of a fastener to resist the pulling of the fastened sheet material over the head of the fastener due to gravity, wind, or other load. The resistance to pullover failure is related to the strength and diameter of the fastener washer and the strength and thickness of the metal panel.

9 Self-Drilling Fasteners Impax Performance Self-Drill Impax and 1/4-14 Impax lap self-drill For metal to metal Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength steel and nested purlins. Ultimate performance in light, medium and heavy gage applications Impax Metal to metal Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate 1/4-14 Impax Lap Panel to panel side lap Drilling capacity: Some applications may require attaching light gage (24 26 ga) to sub-structural member. Composite thickness should not exceed.095. Designed and engineered to have low driving and thread engagement torque and provide maximum clamp load. Corrosion resistant coating system. Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins. NEGATIVE reduced 00% Part No. Part No. Part No. Part No. Length #12 Bond Seal (15 mm) #12 No Washer 1/4-14 Impax Lap w/ Bond Seal 1/4-14 Lap No Washer x 3/4" V2361-EDF A2361F x 1" V4577-EDF S4577F x 1-1/4" V4632-EDF S4632F x 1-1/2" V4677-EDF S4677F x 2" V4777-EDF S4777F File Name: WG3._S5051.eps NEGATIVE reduced 00% Created by: EWB-11/11/ /2" S4902-EDF S4902F Revised: EWB-00/00/ x 3" S4952-EDF S4952F x 4" S4981-EDF S4981F 1/4-14 x 7/8" V5051-GUF S5051F Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options Painted Stainless MAC File Name: 304 stainless bimetal.eps Created by: EWB-11/27/02 5/16" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 2900 Torsional: 92 in-lbs Shear: 2050 Pull-out (lbs ult.): 1" 4" 3/4" 12 ga (.109): ga (.075): ga (.060): Pull-over with Bond Seal (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 654 5/16" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 150 in-lbs Shear: 2850 Pull-out (lbs ult.):- 22 ga (.030): ga (.024): ga (.018): 204 AC a MAC irius Prisma Painted irius Sentri ZAC SX Painted Self Drilling MAC Sentri BI-METAL Prisma SX Self Drilling irius BI-METALPainted Sentri SX SX VistaCoat irius ZAC Stainless Sta S SeS ACA irius MAC PRISMA irius ZAC ZAC MAC PRISMA irius ? ?

10 Self-Drilling Fasteners Impax Heavy Metal Thickness Structural Drill Screws Impax 4.5 and 5 self-drill For metal to metal Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength steel and nested purlins. Delivers ultimate performance in medium and heavy gage applications Impax 4.5 Metal to metal Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Thread length: x 1-1/4":.650 Min projection: 3/16" of threads below substrate Impax 5 Metal to metal Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness. Thread length: x 1-1/4": x 1-1/2": x 2": Min projection: 3/16" of threads below substrate NEGATIVE reduced 00% Designed and engineered to have low driving and thread engagement torque and provide maximum clamp load. Corrosion resistant coating system. 5/16" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3450 Torsional: 100 in-lbs Shear: 2420 Pull-out (lbs ult.): 12 ga (.105): /16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile value Pull-over with Bond Seal (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 584 5/16" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3450 Torsional: 100 in-lbs Shear: 2420 Pull-out (lbs ult.): 12 ga (.105): /16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile value File Name: WG3.1_S4661.eps Pull-over with Bond Seal (lbs ult.): Created by: EWB-11/11/02 22 ga (.030): 1049 Revised: EWB-00/00/02 24 ga (.024): ga (.018): 584 Notes Dimensions are nominal inches unless noted. Self-drill pull out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. Part No. Part No. Length Bond Seal (15 mm) No Washer Impax x 1-1/4" S4661-EDF S4661F NEGATIVE reduced 00% Impax x 1-1/4" S4668-EDF S4668F x 1-1/2" S4741-EDF S4741F x 2" A2841-EDF A2841F File Name: WG2.2_S4668.eps Created by: EWB-11/27/02 Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. rius Painted ZAC Sentri MAC SX Self Drilling Prisma BI-METAL irius Painted Sentri SX SXSelf Self Drilling BI-METAL Painted ZAC MAC Stainless Stainless irius ZAC ZAC MAC PRISMA irius ? ??

11 Self-Drilling Fasteners Impax Sealer Drill Screws Impax sealer and 1/4-14 lap sealer self-drill For metal to metal Integral cupped Hex Washer Head configuration fastener with an EPDM sealing washer instead of the traditional bonded sealing washer. Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength steel and nested purlins Sealer Impax Metal to metal Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate Delivers ultimate performance in light, medium and heavy gage applications. Designed and engineered to have low driving and thread engagement torque and provide maximum clamp load. Corrosion resistant coating system. 5/16" AF Cupped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 2900 Torsional: 92 in-lbs Shear: 2050 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 724 Pull-over (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 692 1/4-14 Sealer Impax Lap Panel to panel side lap Drilling capacity: Some applications may require attaching light gage (24 26 ga) to sub-structural member. Composite thickness should not exceed.095 NEGATIVE reduced 00% File Name: WG2.3_S4636.eps Created by: EWB-11/27/02 5/16 Cupped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 150 in-lbs Shear: 2850 Pull-out (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 204 Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins. Part No. Part No. Length #12 Sealer 1/4-14 Sealer Lap x 3/4" V4486-FGF x 1" V4611-FGF x 1-1/4" V4636-FGF x 1-1/2" V4721-FGF 1/4-14 x 7/8" V5076-FFF NEGATIVE reduced 00% Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options Painted File Name: WG2.3_S5076.eps Created by: EWB-11/27/02 a irius Painted Sentri SX Self Drilling BI-METAL VistaCoat Stainless MA irius ?

12 Self-Drilling Fasteners Impax 1/4" Drill Screws 1/4-14 and 1/4-20 Impax self-drill For metal to metal Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength steel and nested purlins. Impax #2 point is designed with a reduced drill point diameter to provide higher pullout in single purlin attachment. Delivers ultimate performance in medium and heavy gage applications. Designed and engineered to have low driving and thread engagement torque and provide maximum clamp load. Corrosion resistant coating system. 1/4-14 Impax HWH #2 Point and #3 Point Metal to metal Drilling capacity: #2 point: #3 point: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate #2 5/16 AF Hex Washer Head #3 3/8" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 150 in-lbs Shear: 2850 #2 Point Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 903 #3 Point Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 687 Pull-over with Bond Seal (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 616 1/4-20 Impax HWH #4 Point Metal to metal Drilling capacity: Thickness is based NEGATIVE on reduced normal, 00% single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate File Name: WG2.4_S5155.eps Created by: EWB-11/27/02 3/8" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 4200 Torsional: 156 in-lbs Shear: 2920 Pull-out (lbs ult.): 12 ga (.030): ga (.024): ga (.018): 707 Pull-over with Bond Seal (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 629 Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. NEGATIVE reduced 00% File Name: WG(1.4)_14_20SpecialApp.eps Created by: EWB-12/13/02 Continued on following page

13 Self-Drilling Fasteners Impax 1/4" Drill Screws 1/4-14 and 1/4-20 Impax self-drill For metal to metal Part No. Part No. Part No. Part No. Part No. Part No. #3 & #4 Point #3 & #4 Point #2 Point Bond Seal #2 Point No Washer #2 Point Bond Seal #2 Point No Washer Length Bond Seal No Washer 5/16" HWH 5/16" HWH 3/8" HWH 3/8" HWH 1/4-14 x 3/4" S5010-GBF S5010F 1/4-14 x 1" S5155-GBF S5155F S5171-GBF S5171F 1/4-14 x 1-1/4" S5201-GBF S5201F S5191-GBF S5191F 1/4-14 x 1-1/2" S5251-GBF S5251F S5286-GBF S5286F S5271-GBF S5271F 1/4-14 x 2" S5351-GBF S5351F 1/4-14 x 2-1/2" S5381-GBF S5381F 1/4-14 x 3" S5451-GBF S5451F 1/4-14 x 4" S5461-GBF S5461F 1/4-20 x 3" #4 Point S5611-GBF S5611 1/4-20 x 4" #4 Point S5621-GBF S5621F 1/4-20 x 5" #4 Point S5641-GB S5641 1/4-20 x 6" #4 Point S5661-GB S5661 1/4-20 x 7" #4 Point S5671-GB S5671 1/4-20 x 8" #4 Point S5681-GB S5681 Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options rius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

14 Self-Drilling Fasteners Impax Utility Self-Drill Precision cold forged assuring superior point strength and the fastest drilling time performance. Ultimate performance in light and medium gage applications. Designed to provide maximum clamp load. Corrosion resistant coating system Impax #2 Point Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate #3 Point Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate 1/4" AF Capped Hex Washer Head Thread Major Dia:.163 Thread Minor Dia:.119 Tensile: 1575 Torsional: 42 in-lbs Shear: 1035 #2 Point Pull-out (lbs ult.): 14 ga (.075): ga (.060): ga (.048): 389 Pull-over with Bond Seal (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 421 5/16" AF Hex Washer Head Thread Major Dia:.186 Thread Minor Dia:.138 Tensile: 1825 Torsional: 48 in-lbs Shear: 1535 #3 Point Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 782 Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. Impax 1/4 HWH Self Drill With Bond Seal Without Bond Seal 8-18 x 1/2 HWH SD #2 S1050-BBF S1050F 8-18 x 5/8 HWH NIB SD #2 S1320F 8-18 x 3/4 HWH SD #2 S1350-BBF S1350F Impax 5/16 HWH Self Drill With Bond Seal Without Bond Seal x 5/8 HWH SD #2 S2401-CDF S2401F x 3/4 HWH SD #3 S2701-CDF S2701F x 1 HWH SD #3 S3301-CDF S3301F x 1-1/4 HWH SD #3 S3601-CDF S3601F x 1-1/2 HWH SD #3 S3901-CDF S3901F Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options rius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

15 Self-Drilling Fasteners 410 Stainless and 1/4-14 lap self-drill For metal to metal 410 SS is a magnetic heat-treatable stainless steel. Type 410 self-drilling fasteners provide fair resistance to corrosion in mild to light industrial environments Stainless SD #3 Point Metal to metal Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate 1/4-14 Stainless Lap Panel to panel side lap Drilling capacity: Some applications may require attaching light gage (24 26 ga) to sub-structural member. Composite thickness should not exceed /16" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 2800 Torsional: 92 in-lbs Shear: 1900 Point Pull-out (lbs ult.): 12 ga (.109): ga (.075): ga (.060): 624 Pull-over with Bond Seal (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 654 5/16" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3850 Torsional: 150 in-lbs Shear:2850 Pull-out (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 204 Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accomodate nested purlins. Part No. Part No. Part No. Part No. Length #12 Bond Seal #12 No Washer 1/4-14 Lap w/ Bond Seal 1/4-14 Lap No Washer x 3/4" SD3 G0325-FBF G0325F x 1" SD3 G0340-FBF G0340F x 1-1/4" SD3 G0801-FBF G0801F x 1-1/2" SD3 G0810-FBF G0810F 1/4-14 x 7/8" G0773-GWF G0773F Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options rius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

16 Self-Drilling Fasteners Flat Head Utility Self-Drill Wood to Metal For attaching plywood to steel Designed for attaching wood substrates to steel. Phillips drive and head design for counter sinking. Ply Metal Self-Drill Wafer Head #2 Phillips Drive Drilling capacity: More threads per inch for optimum holding power. Head Dia:.445 Thread Major Dia:.186 Header Self-Drill with Wings Flat Head #3 Phillips Drive Drilling capacity: Head Dia:.413 Thread Major Dia:.212 1/4-20 Flat Head Header Self-Drill #3 Phillips Drive Drilling capacity: Head Dia:.479 Thread Major Dia:.246 Notes Dimensions are nominal inches unless noted. The specific job conditions should be considered and appropriate safty factors applied when specifying the proper fasteners. Length Wood Thickness Steel Thickness Part No x 3/4" 3/8" plywood A x 1" 1/2" plywood A x 1-7/16" 3/4" plywood A x 2" up to 1" A x 2-1/2" up to 1-1/2" A2860 1/4-20 x 2-3/4" up to 1-3/4" A5085 Installation Tools: rpm screwdriver equipped with depth sensing nosepiece.

17 Alloy Capped Fasteners ZAC Impax 5/16" HWH Alloy Capped ZAC 5/16" HWH Zinc aluminum capped drill screws For metal to metal ZAC: the most widely used zinc aluminum capped fastener in the industry. Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength steel and nested purlins ZAC (5/16") Metal to metal Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate Integral cupped Hex Washer Head can never red rust. Designed and engineered to have low driving and thread engagement torque while providing maximum clamp load. 5/16" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 2900 Torsional: 92 in-lbs Shear: 2050 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 724 Pull-over (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 794 1/4-14 ZAC Lap (5/16") Panel to panel side lap Drilling capacity: Some applications may require attaching light gage (24 26 ga) to sub-structural member. Composite thickness should not exceed.095 thickness. NEGATIVE reduced 00% File Name: WG5.1_S464.eps Created by: EWB-11/27/02 5/16" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 150 in-lbs Shear: 2850 Pull-out (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 204 Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing and we believe typical. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins. Part No. Part No. Length ZAC 1/4-14 ZAC Lap 5/16" AF Hex Washer Head ZAC x 1" S4591-FLF x 1-1/4" X4646-FLF x 1-1/2" NEGATIVE reduced 00% X4731-FLF x 2" S4761-FLF 1/4-14 x 7/8" S5031-FMF File Name: 304 stainless bimetal.eps Created by: EWB-11/27/02 Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options a irius Painted Sentri SX Self Drilling BI-METAL VistaCoat Painted Stainless MA irius ?

18 Alloy Capped Fasteners ZAC Impax 3/8" HWH Alloy Capped ZAC 3/8" HWH Zinc aluminum capped drill screws For metal to metal ZAC: the most widely used zinc aluminum capped fastener in the industry. Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength steel and nested purlins ZAC (3/8") Metal to metal Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/16" of threads below substrate. Integral cupped Hex Washer Head can never red rust. Designed and engineered to have low driving and thread engagement torque while providing maximum clamp load. 3/8" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 2900 Torsional: 92 in-lbs Shear: 2050 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 724 Pull-over (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 794 1/4-14 ZAC Lap (3/8") Panel to panel side lap Drilling capacity: Some applications may require attaching light gage (24 26 ga) to sub-structural member. Composite thickness should not exceed.095 thickness. NEGATIVE File Name: WG5.2_S4631.eps Created by: EWB-11/27/02 3/8" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 150 in-lbs Shear: 2850 Pull-out (lbs ult.): 22 ga (.030): ga (.024): ga (.018): x 3/4 ZAC Lap (3/8") Sharp point Panel to panel Drilling capacity Self-piercing points are not designed for attaching light gage (24 26 ga) to sub-structural member. NEGATIVE reduced 00% File Name: WG5.2_S5065.eps Created by: EWB-11/27/02 3/8" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 2100 Torsional: 92 in-lbs Shear: 1800 Pull-out (lbs ult.) 22 ga (.030): ga (.024): ga (.018): 330 Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins. NEGATIVE reduced 00% File Name: WG5.2_A1653.eps Created by: EWB-11/27/02 Continued on following page

19 Alloy Capped Fasteners ZAC Impax 3/8" HWH Alloy Capped ZAC 3/8" HWH Zinc aluminum capped drill screws For metal to metal Part No. Part No.. Length /4-14 Lap) 3/8" Hex Washer Head ZAC x 3/4" A1653-FLF Sharp Point LAP x 1" S4576-FLF x 1-1/4" S4631-FLF x 1-1/2" S4676-FLF x 2" S4776-FLF x 2-1/2" S4901-FLF x 3" S4951-FLF 1/4-14 x 7/8" S5065-FMF Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options a irius Painted Sentri SX Self Drilling BI-METAL VistaCoat Painted Stainless MA irius ?

20 Alloy Capped Fasteners ZAC Impax 3/8" HWH Alloy Capped ZAC self-drill 3/8" HWH Zinc aluminum capped drill screws For metal to metal and insulated panel to metal ZAC: the most widely used zinc aluminum capped fastener in the industry. Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength steel and nested purlins ZAC (3/8") 4.5 point and 5 point Metal to metal Impax 4.5 Drilling capacity: Impax 5 Drilling capacity: Thickness is based on single thickness purlin/girt or multiple material thickness combined for total. Thread length: ZAC 4.5: x 1-1/4":.650 ZAC 5: x 1-1/4": x 1-1/2": x 2": Min projection: 3/16" of threads below substrate Designed and engineered to have low driving and thread engagement torque to prevent damage to the cap during installation while providing maximum clamp load. Integral cupped Hex Washer Head can never red rust. 3/8" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3450 Torsional: 100 in-lbs Shear: 2420 Pull-out (lbs ult.): 12 ga (.105): /16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile value Pull-over with assembled Seal washer (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 794 Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins. Part No. Part No. Panel Length Insulated (4.5 ) and (5) Thickness x 1-1/4" (4.5) S4665-FLF File Name: WG5.2_S4665.eps x 1-1/4" (5) NEGATIVE reduced 00% S4669-FLF Created by: EWB-11/27/ x 1-1/2" (5) S4742-FLF Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options rius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

21 Alloy Capped Fasteners MAC Impax 5/16" HWH 300 Series Stainless Capped Self-Drill MAC stainless capped drill screws For metal to metal MAC has a 300 series stainless steel capped, integral cupped Hex Washer Head configuration that can never red rust MAC Assembled with EPDM washer Metal to metal Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total, as in overlapped or nested purlin construction. Min projection: 3/16" of threads below substrate Designed and engineered to have low driving and thread engagement torque and provide maximum clamp load. 5/16 AF Stainless Capped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 2900 Torsional: 92 in-lbs Shear: 2050 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 724 Pull-over (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 692 1/4-14 MAC Lap Assembled with EPDM washer Panel to panel side lap Drilling capacity: Some applications may require attaching light gage (24 26 ga) to sub-structural POSITIVE member. reduced 00% Composite thickness should not exceed.095 thickness. NEGATIVE reduced 00% MAC 4.5 Assembled with EPDM washer Metal to metal Drilling capacity: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Nominal thread length: x 1-1/4":.650 Min projection: NEGATIVE 3/16" of reduced threads 00% below substrate File Name: WG5.3_S4650.eps Created by: EWB-11/27/02 File Name: WG5.3_S5100.eps Created by: EWB-11/27/02 5/16 AF Stainless Capped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 150 in-lbs Shear: 2850 Pull-out (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 204 5/16 AF Stainless Capped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3450 Torsional: 100 in-lbs Shear: 2420 Pull-out (lbs ult.): 12 ga (.105): /16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile value Pull-over (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 584 Notes Dimensions are nominal inches unless noted. Self-drill pull out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull out values are based on 40,000 PSI AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins. Part No. Part No. Part No. Length MAC 1/4-14 MAC MAC x 1" S4530-FAF x 1-1/4" S4650-FAF x 1-1/2" S4690-FAF x 2" S4770-FAF 1/4-14 x 7/8" S5100-GGF x 1-1/4" (4.5) NEGATIVE reduced 00% S4672-FAF ZAC MAC PRISMA File Name: WG5.3_S4672.eps irius Created by: EWB-11/27/02 Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options ZAC MAC Prisma irius Painted Sentri SX Self Drilling BI-M VistaCoat Painted Stainless

22 Alloy Capped Fasteners ZAC 3/8" HWH Alloy Capped Tapping Fasteners Integral cupped Hex Washer Head configuration can never red rust. Designed for attaching both metal to wood and metal to metal. 1/4-14 ZAC Type AB Milled Point Metal to wood Metal to metal Self-Drilling Metal Thickness: Sheet Thickness is based on normal, single or multiple POSITIVE material reduced thickness 00% combined for total Min depth penetration into the wood sub structure: 1" #17 Zac Type AB Strip-out Repair Metal to metal Repair fastener for stripped out #14 Type A or 1/4" AB Min projection: 3/8" of threads below substrate ZAC self-tapping fasteners: AB milled point For metal to metal Milled points do not require a pre-drilled hole when attaching 26 and 24 gage metal to wood. 3/8" AF Zinc Aluminum Capped Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 150 in-lbs Shear: 2850 Pull-out (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 204 3/8 AF Hex Head Thread Major Dia: Thread Minor Dia: File Name: WG5.4_A4395.eps Notes NEGATIVE reduced 00% Created by: EWB-11/11/02 Dimensions are nominal inches unless noted. When using Milled point fasteners for metal to metal see the tapping screw section for performance values. Pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. Part No. Part No. Length 1/4-14 AB Length #17 AB 3/8" ZAC 1" A4395-FMF 17 x 1" A6045-LFF 1-1/2" A4485-FMF 17 x 1-1/2" A6066-LFF 2" A4513-FMF 2-1/2" NEGATIVE reduced 00% A4510-FMF File Name: WG5.4_A6045.eps Created by: EWB-11/11/02 Installation Tools: Metal to metal application: rpm screwdriver equipped with depth sensing nosepiece. Metal to wood application: rpm screwdriver equipped with depth sensing nosepiece. Options rius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

23 Capped Fasteners Prisma Nylon headed fasteners: self-tapping, self-drill and Woodgrip For metal to metal and metal to wood Prisma nylon head is absolutely corrosion proof. Nylon head can withstand extreme installation torque without failure. Requires no special socket for installation. #14 Type AB Metal to metal Self-Tapping AB: 1/4-14 x 3/4" 1/4-14 x 1-1/2" 1/4-14 x 2" 1/4-14 x 2-1/2" 1/4-14 x 3" Stainless AB: 1/4-14 x 3/4" Self-Drill: 1/4-14 x 1" 1/4-14 x 1-3/8" 1/4-14 x 2" Drill capacity: Special washer face allows the fastener to be used on sidewall without a sealing washer. Nylon heads are available in 90 standard colours. 7/16" Nylon Hex Washer Head 1/4-14: Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 142 in-lbs Shear: /4-14 AB Carbon Steel: Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 879 1/4-14 #3 Point Carbon Steel: Pull-out: (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 687 1/4-14 x 7/8 Lap Metal to metal Panel to panel side lap drilling capacity: Self-Drilling Metal Thickness: Thickness is based on normal, single or multiple material thickness NEGATIVE reduced 00% combined for total. File Name: WG5.5_prisma2b.eps Created by: EWB-12/04/02 7/16" Nylon Hex Washer Head 1/4-14: Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 142 in-lbs Shear: 2560 #10 Woodgrip Metal to wood 10 x 1" 10 x 1-1/2" 10 x 2" 10 x 2-1/2" 10 x 3" Min depth penetration into the wood sub structure: 1" Woodgrip Prisma 3/8" Nylon Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 1500 Torsional: 60 in-lbs min Shear: 933 Notes Dimensions are nominal inches unless noted. For Type AB metal to metal, see tapping File screw Name: section EG5.5_prisma4.eps for performance values. NEGATIVE reduced 00% Created by: EWB-12/4/02 Options None NEGATIVE reduced 00% File Name: WG5.5_prisma1.eps Created by: EWB-12/04/02

24 Self-Tapping Fasteners Tapping Screws Carbon Steel Self-tapping Type A. AB, B For metal to metal Carbon steel zinc-plated self-tapping fasteners are the original metal construction fastener that can be used in metal to metal and metal to wood applications. Tapping screws are available in long lengths for specialty applications. #14 Type A Metal to metal Attachment thickness: Metal thickness Drill bit size /8 (.125) /16 (.187) #8 (.199) The hole size determines installation performance and pullout strength. Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8" of threads below substrate #14 Type A Milled Point Carbon Steel, Silver Sentri Metal to wood Self-drilling metal thickness: Sheet Thickness is based on normal, single or multiple material thickness combined for total. Min depth penetration POSITIVE into reduced the 00% NEGATIVE reduced 00% wood sub structure: 1" File Name: WG7.1_A3240.eps Created by: EWB-11/27/02 3/8" AF Hex Head Thread Major Dia: Thread Minor Dia: Tensile: 3500 Torsional: 125 in-lbs Shear: 2400 Pull-out (lbs ult.): 14 ga (.075): ga (.060): ga (.048): 605 Pull-over (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 564 5/16" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3500 Torsional: 125 in-lbs Shear: 2400 Pull-out (lbs ult.): 1" SPF wood: 1013 Pull-over (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 564 1/4 Type AB and B Metal to metal Attachment thickness: Metal thickness Drill bit size AB /8 (.125) AB /32 (.156) AB #8 (.199) AB #7 (.201) B #8 (.199) B POSITIVE #7 reduced (.201) 00% B #1 (.228) B NEGATIVE #1 or reduced larger, 00% depending on hardness of steel Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8" of threads below substrate File Name: WG6.4_A3321.eps Created by: EWB-11/27/02 3/8" AF Hex Head Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional:142 in-lbs Shear: 2560 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 879 Pull-over (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 600 Notes Dimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. NEGATIVE reduced 00% File Name: WG7.1_A4420.eps Created by: EWB-11/27/02 Continued on following page

25 Self-Tapping Fasteners Tapping Screws Carbon Steel Self-tapping Type A. AB, B For metal to metal #17 Type AB Strip out repair Type A or AB Metal to metal Attachment thickness: Min projection: 3/8" of threads below substrate 3/8" AF Hex Head Thread Major Dia: Thread Minor Dia: Notes Dimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. Part No. Part No. Part No. Part No. Length* #14 A Bond Seal #14 A Milled Point Bond Seal 1/4 AB & #17 AB Bond Seal 1/4 B Bond Seal 3/4" A2980-GB A4320-GB A3800-GB 1" A3240-GB V3321-GBF A4420-GB A3860-GB 1-1/4" A3420-GB A4440-GB 1-1/2" A3460-GB V3438-GBF A4500-GB A3920-GB 2 " A3520-GB V3531-GBF File Name: WG7.1_A6040.eps A4000-GB 2-1/2" NEGATIVE reduced 00% Created by: EWB-11/27/02 A3580-GB A3597-GBF Revised: MPD-00/00/02 A4040-GB 3" A3620-GB A3626-GBF A4080-GB 3-1/2" A3640-GB A4140-GB 4" A3680-GB A4220-GB 5" A3720-GB A4260-GB 6" A3740-GB A4280-GB #17 x 3/4" A6020-KJ #17 x 1" A6040-KJ #17 x 1-1/2" A6060-KJ *Longer lengths available upon request Installation Tools: rpm on type B screwdriver equipped with depth sensing nosepiece. Options a irius Painted ZAC Sentri MAC SX Self DrillingPrisma BI-METAL irius Painted Sentri SX Self Drilling B VistaCoat Painted ZAC Stainless Stainless MA irius ZAC MAC PRISMA irius ?

26 Self-Tapping Fasteners Tapping Screws 300 Series (RH2) Product Name: #14 Stainless Steel Stainless (RH3) self-tapping Description: #3 Type Phillips A, AB, Drive B (RH4) : Insulation board For metal to roof to cover. metal Stainless steel zinc-plated self-tapping fasteners are designed for attaching metal to metal and metal to wood. Type B have wax surface treatment for added lubricity. #14 Type A 304 Stainless Metal to metal Attachment thickness: Metal thickness Drill bit size /8 (.125) /16 (.187) #8 (.199) The hole size determines installation performance and pullout strength. Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8" of threads below substrate Type AB and B 304 Stainless Metal to metal Attachment thickness: Metal thickness Drill bit size AB /8 (.125) AB /32 (.156) AB #8 (.199) AB #7 (.201) NEGATIVE reduced 00% B #8 (.199) B #7 (.201) B #1 (.228) B #1 or larger, depending on hardness of steel Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8" of threads below substrate #17 Type AB 304 Stainless Strip out repair Type A or AB Metal to metal Min projection: 3/8" of threads below substrate NEGATIVE reduced 00% Stainless tappers are used in high corrosive environments or where corrosions free performance is required to meet the design life of the project. File Name: WG7.2_E0600.eps Created by: EWB-11/27/02 File Name: WG7.2_E0880.eps Created by: EWB-11/27/02 3/8" AF 304 Stainless Hex Head Thread Major Dia: Thread Minor Dia: Tensile: 3370 Torsional: 125 in-lbs Shear: 1520 Pull-out (lbs ult.) 14 ga (.075): ga (.060): 1110 Pull-over (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 647 3/8" AF 304 Stainless Hex Head Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 142 in-lbs Shear: 2350 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 1250 Pull-over (lbs ult.): 22 ga (.030): ga (.024): ga (.018): 647 3/8" 304 Stainless AF Hex Head Thread Major Dia: Thread Minor Dia: Notes Dimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. Continued on following page

27 Self-Tapping Fasteners Tapping Screws 300 Series Stainless Steel Stainless self-tapping Type A, AB, B For metal to metal Part No. Part No. Part No. Length #14 A Bond Seal 1/4 AB & #17 AB Bond Seal 1/4 B Bond Seal 3/4" E0500-HP E1240-HP E0860-HPW 1" E0600-HP E1300-HP E0880-HPW 1-1/4" E0640-HP E1310-HP 1-1/2" E0660-HP E1320-HP E1000-HPW 2" E0700-HP E1060-HPW 2-1/2" E0720-HP E1080-HPW 3" E0740-HP E1100-HPW 3-1/2" E0760-HP E1120-HPW 4" E0780-HP E1140-HPW 5" E0820-HP E1180-HPW 6" E0840-HP E1200-HPW 7" E0850-HP E1210-HPW 8" E0855-HP E1215-HPW #17 x 3/4" E1960-KP #17 x 1" E1980-KP #17 x 1-1/2" E2000-KP Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options irius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

28 Architectural Fasteners SX Stainless Self-Drill SX austenitic stainless steel For metal to metal SX Austenitic stainless fasteners come with a Bi-metal welded carbon steel point. SX Austenitic stainless product line offers fastening solutions for attaching panels from very thin to 1/2" structural steel. Provides ultimate corrosion performance for attaching steel, stainless or aluminum panels. Designed for secured attachment to both panel and substructures. SX3 Self-Drill 5/8" O.D Stainless Bond Seal Metal to metal Drill capacity: SX5 Self-Drill 5/8" O.D Stainless Bond Seal Metal to metal Drill capacity: SX14 Self-Drill 5/8" O.D Stainless Bond Seal Metal to metal Drill capacity: SL2-S Free Spin Lap Self-Drill 1/2" (14mm) O.D. for #12 5/8" (16mm) O.D. for #14 Stainless Bond Seal Metal to metal Drill capacity: Stainless self-drill fasteners are engineered to have low driving torque and provide maximum clamp load. Ultimate drill performance in light, medium, and heavy gage applications. Washer O.D designed for both sidewall and roof panel attachment. 5/16" AF Hex Washer Head Dia: Nominal #14 Tensile: 2535 Torsional: 70 in-lbs Shear: 1864 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 610 Pull-over (lbs ult.): 24 ga (.024): ga (.018): 705 5/16" AF Hex Washer Head Dia: Nominal #12 Tensile: 2735 Torsional: 70 in-lbs Shear: 2240 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 582 Pull-over (lbs ult.): 24 ga (.024): ga (.018): 665 5/16" AF Hex Washer Head Dia: Nominal #12 Tensile: 2695 Torsional: 70 in-lbs Shear: 2695 Pull-out (lbs ult.): 12 ga (.105): /16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile value Pull-over (lbs ult.): 24 ga (.024): ga (.018): 646 5/16" AF Hex Washer Head Dia: Nominal #14 Tensile: 3740 Torsional: 70 in-lbs Shear: /16" AF Hex Washer Head Dia: Nominal #12 Tensile: 1670 Torsional: 70 in-lbs Shear: 1370 Continued on following page

29 Architectural Fasteners SX Stainless Self-Drill SX austenitic stainless steel For metal to metal continued SXC14 Self-Drill Standoff 3/4" O.D Stainless Bond Seal Insulated panel to metal #5 Point Drill capacity: /16" AF Hex Washer Head Dia: Nominal #12 Tensile: 3150 Torsional: 92 in-lbs Shear: 2780 SXCW Self-Drill 3/4" O.D Stainless Bond Seal Insulated panel to wood Drill capacity: /16" AF Hex Washer Head Dia: Nominal 1/4" Tensile: 3934 Torsional: 95 in-lbs Shear: 2450 Part No. Part No. Part No. Part No. Length Bond Seal No Washer Length Bond Seal No Washer SX3 Self-Drill Stainless HWH SX14 Self-Drill Stainless HWH x 1-1/8 SD x 1-9/16 SD x 1-1/2 SD x 1-7/8 SD x 2 SD x 2-1/2 SD SX5 Self-Drill Stainless HWH x 3-1/4 SD x 1-1/4 SD x 4 SD x 1-1/2 SD Part No. Panel x 1-5/8 SD Length Bond Seal Thickness x 2-1/8 SD SXC14 Self-Drill x 3-1/8 SD x 3-1/8" /2" 1-7/8" x 3-3/4 SD x 3-3/4" /8" 2-1/2" x 4-1/4 SD x 4-5/8" /8" 3-5/16" x 5-1/2 SD x 5-1/2" /16" 4-1/8" SL2 Lap Self-Drill Stainless HWH x 6-5/8" /8" 5-5/16" x 1 Lap SD SXCW Self-Drill 1/4-14 x 1-1/8 Lap SS x 3-1/2" /8" 1-7/16" 14 x 4-1/8" /2" 2-1/8" 14 x 4-9/16" /8" 2-9/16" 14 x 5-3/8" /8" 3-5/16" 14 x 6-1/4" /16" 4-1/8" Installation Options Tools: 0 ZAC 2000 rpm screwdriver MAC equipped Prisma with ZAC depth sensing MAC nosepiece. irius Prisma Painted irius Sentri Painted SX Self Drilling Sentri BI-METAL SX Painted irius Stainless Stainless Self Drilling ZAC MAC PRISMA ZAC MAC irius PRISMA irius ? 4

30 Architectural Fasteners irius SX Stainless Self-Drill irius SX austenitic stainless steel For metal to metal irius is a patented drive system available on a full range of metal building fasteners. irius SX stainless fasteners low profile head that has changed the future architectural appearance of sidewall fastening. Fastening system drive socket insures positive engagement and prevents damage to a painted fastener head. SX 3-L12 irius Self-Drill 1/2" O.D Aluminum Bond Seal Metal to metal Drill capacity: SX 5-L12 irius Self-Drill 1/2" O.D Aluminum Bond Seal Metal to metal Drill capacity: SX 14-L12 irius Self-Drill 5/8" O.D Stainless Bond Seal Metal to metal Drill capacity: SL2-S-L12 irius Free Spin Lap Self-Drill 1/2" or 5/8" O.D Stainless Bond Seal Metal to metal Drill capacity: Self-drilling point design assures superior point strength and the excellent drill performance through high strength steel. Stainless fasteners provide the ultimate corrosion performance for attaching steel, stainless or aluminum panels. SX austenitic stainless self-drill fasteners are engineered to have low driving torque and provide maximum clamp load. irius low profile and drive system Dia: Nominal #14 Tensile: 2535 Torsional: 70 in-lbs Shear: 1864 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 610 Pull-over (lbs ult.): 24 ga (.024): ga (.018): 705 irius low profile and drive system Dia: Nominal #12 Tensile: 2735 Torsional: 70 in-lbs Shear: 2240 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 582 Pull-over (lbs ult.): 24 ga (.024): ga (.018): 665 irius low profile and drive system Dia: Nominal #12 Tensile: 2695 Torsional: 70 in-lbs Shear: 2695 Pull-out (lbs ult.): 12 ga (.105): /16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile value Pull-over (lbs ult.): 24 ga (.024): ga (.018): 646 irius low profile and drive system Dia: Nominal #12 Tensile: 1670 Torsional: 70 in-lbs Shear: 1370 NEGATIVE reduced 00% File Name: WG3_SX14.eps Created by: EWB-12/19/02 Continued on following page

31 Architectural Fasteners irius SX Stainless Self-Drill irius SX austenitic stainless steel For metal to metal Part No. Part No. Length Bond Seal No Washer SX3-L12 irius Self-Drill 14 x 1-1/8 SD x 1-1/2 SD SX5-L12 irius Self-Drill x 1-1/4 SD x 1-1/2 SD x 1-5/8 SD x 2-1/8 SD SX14-L12 irius Self-Drill x 1-9/16 SD SL2-L12 irius Free Spin Lap Self Drill 1/4-14 x 1 Lap SD 14mm SS Bond Seal /4-14 x 1 Lap SD 16mm SS Bond Seal Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. The E420 irius drive socket (part # ) is required. Options irius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

32 Architectural Fasteners SX TORX Self-Drill SX austenitic stainless steel For metal to metal SX Austenitic stainless fasteners come with a Bi-metal welded carbon steel point. SX Austenitic stainless product line offers fastening solutions for attaching panels from very thin to medium gage applications. Provides ultimate corrosion performance for attaching steel, stainless or aluminum panels. SX 3-D10 TORX Self-Drill Metal to metal Drill capacity: Low profile TORX drive for aesthetic installed appearance Designed for secured attachment to both panel and substructures. Stainless self-drill fasteners are engineered to have low driving torque and provide maximum clamp load. Ultimate drill performance in light and medium gage applications. Drive TORX T20W Head Dia Thread Major Dia Thread Minor Dia Strength (ult.): Tensile: 1960 lbs Shear: 1456 lbs Pull-out (ult.): 12 ga (.105): 1189 lbs 14 ga (.075): 854 lbs 16 ga (.060): 696 lbs SX 5-D12 TORX Self-Drill 1/2" O.D Aluminum Bond Seal Metal to metal Drill capacity: SL2-S-D12 Lap TORX Self-Drill 3/8 O.D. Aluminum Bond Seal Metal to metal Drill capacity:.060 Drive TORX T-25 Head Dia Thread Major Dia Thread Minor Dia Strength (ult.): Tensile: 2735 lbs Torsional: 2240 lbs Shear: 70 lb-in Pull-out (ult.): 12 ga (.105): 1399 lbs 14 ga (.075): 795 lbs 16 ga (.060): 582 lbs Drive TORX T20W Head Dia Thread Major Dia Thread Minor Dia Strength (ult.): Tensile: 1670 lbs Torsional: 70 lb in Shear: 1370 lbs Pull-out (ult.): 16 ga (.060): 902 lbs 18 ga. (.048): 668 lbs Notes Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safty factors applied when specifying the proper fasteners. Continued on following page

33 Architectural Fasteners SX TORX Self-Drill SX austenitic stainless steel For metal to metal Part No. Part No. Length Bond Seal No Washer SX3-D10 TORX x 1 SD T20W x 1-3/16 SD T SX5-D12 TORX x 1-1/2 SD SL2-S-D12 Lap TORX 12 x 1 LAP SD Installation Fasteners should provide for a minimum of 3 fully developed threads through the metal substrate. Tools: rpm screwdriver equipped with depth sensing nosepiece. T20W or T25 TORX drive bit. Options irius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

34 Architectural Fasteners TW-S Stainless Self-Tapping Fastening cladding to timber battens, aluminum and steel framework Aesthetic fastening system for attaching cladding panels to timber battens, aluminum and steel framework. Low profile TORX drive head can be colored to match any cladding panel. TW-S-D12 #10-12 Self-Tapping Cladding Panel to Wood Material: 304 Austentic Stainless Steel TW-S-D13 #12-11 Self-Tapping Cladding Panel to Metal 304 Stainless Steel provides maximum resistance to corrosion. Drive: TORX T20W Head Dia: Thread Major Dia: Thread Minor Dia: Nom. Tensile: 1596 lbs Min. Torsional: 60 lb-in Nom. Shear: 1213 lbs Pull-out Strength - SYP Dimensional Lumber 1/4 : 481 lbs Pull-out Strength - Plywood 3/4 : 578 lbs 5/8 : 438 lbs 1/2 : 348 lbs Pull-out Strength - OSB (Oriented Strand Board) 23/32 : 449 lbs 19/32 : 412 lbs 7/16 : 228 lbs Drive: TORX T20W Head Dia: Thread Major Dia: Thread Minor Dia: Material: 304 Austentic Stainless Steel Nom. Tensile: Min. Torsional: Nom. Shear: 2144 lbs 65 lb-in 2200 lbs Pull-out Strength - Extruded Aluminum 1/8 : 800 lbs pre-drill: 13/64 (.203 ) 1/4 : 1800 lbs pre-drill: 13/64 (.203 ) Pull-out Strength - 55 KSI Yield Sheet Steel 16 ga. (.060 ) 637 lbs pre-drill: 3/16 (.187 ) Notes: Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safety factors applied when specifyng the proper fasteners. Description Part No. Global Code TW-S-D x TW-S-D12-4,8X x 1-1/ TW-S-D12-4,8X x 1-1/ TW-S-D12-4,8X x 1-3/ TW-S-D12-4,8X x 2-3/ TW-S-D12-4,8X60 TW-S-D x TW-S-D13-5,5X x 1-1/ TW-S-D13-5,5X x 1-1/ TW-S-D13-5,5X38 Installation Options Stainless Fastener length should provide for ZAC a minimum of 1 MAC penetration into Prisma wood substrate. irius Painted Painted Sentri SX Self Drilling BI-M Fastener length should provide for a minimum of 3/16 penetration of fully developed threads into metal substrate. Check with cladding panel manufacturer for specific installation guidelines. ZAC MAC PRISMA irius Tools: rpm screwdriver with depth sensing nosepiece. T20W TORX drive bit

35 Architectural Fasteners SLA Self-Drill Fastening aluminum composite panels to aluminum 304 austenitic stainless steel provides the optimum corrosion resistance performance. TORX T20W drive makes installaton fast and easy. Resistant to overdrive. SLA3 Self-Drill Aluminum composite panels to aluminum framework Drilling Capacity (Aluminum): Material: 304 Austentic Stainless Steel A2, material number , AISI 304 Resistant to back out. Low profile provides for an aesthetically pleasing façade. Custom color matching to your panel is available with scratch resistant coating Drive: TORX T20W Head Dia:.470 Dia Nominal:.190 Tensile: Shear: 1765 lbs 1177 lbs Pull-out Strength AlMg 1.8 mm (.07l ): 440 lbs AlMg 2 mm (.079 ): 517 lbs Notes: Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safety factors applied when specifyng the proper fasteners. Description Part No. Global Code Grip Range x 3/4" SD SLA3/6 S-D12-4,8X " Installation rpm screwdriver equipped with depth sensing nosepiece. T20W TORX drive bit. Options irius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

36 Architectural Fasteners SA6/TDA Panel Fabrication Fasteners 304 austenitic stainless steel Ensures compatability between fastener, panel and framework SA6 PHL Pan Head #10-16 Self-Drill Panel to Aluminum Aluminum to Aluminum Drilling capacity: Max.118 Material: 304 Austenitic Stainless Steel SA6 PHL Flat Head #10-16 Self-Drill Panel to Aluminum Aluminum to Aluminum Drilling capacity: Material: 304 Austenitic Stainless Steel TDA PHL Flat Head #10 Self-Tapping Type A Cladding Panel to Metal Metal to Metal Material: 304 Austenitic Stainless Steel Drive: #2 Philips Head Dia:.365 Thread Major Dia:.182 Thread Minor Dia:.134 Strength (ult.): Tensile: 1420 lbs Torsional: 50 in-lbs Shear: 1270 lbs Pull-out Strength - Aluminum.057 Aluminum: 465 lbs Assembled Shear Strength 1/8 Alum. Bracket to.057 Alum 687 lbs Drive: #2 Philips Head Dia:.346 Thread Major Dia:.185 Thread Minor Dia:.132 Strength (ult.): Tensile: 1760 lbs Torsional: 55 in-lbs Shear: 1182 lbs Pull-out Strength - Extruded Aluminum: 1/8 (.125 ): 823 lbs Drive: #2 Philips Head Dia:.346 Thread Major Dia:.185 Thread Minor Dia:.132 Strength (ult.): Tensile: 1760 lbs Torsional: 55 in-lbs Shear: 1182 lbs Pull-out Strength - Extruded Aluminum: 1/8 (.125"): 920 lbs pre-drill #21 (.159 ) Notes: Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. Description Part No. Global Code SA6 PHL Pan Head #10 x 3/4" SA6/6-D9-PH2-4,8X19 SA6 PHL Flat Head #10 x 3/4" SA6/6-PH2-4,8X19 #10 x 1" SA6/11-PH2-4,8X25 TDA PHL Flat Head #10 x 3/4" Type A TDA-S-PH2-4,8X19 #10 x 1" Type A TDA-S-PH2-4,8X25 Installation Fasteners should provide for a minimum of 3 fully developed threads through the metal substrate. Tools: rpm screw driver equipped with depth sensing nosepiece.

37 Architectural Fasteners AP Rivet Fastening cladding panels to aluminum or steel framework Can be used in assemblies of dissimilar materials, thick and thin, hard and soft, metal, composites and phenolic panels Good installed appearance Tamper resistant Won t loosen in high vibration and fatigue applications Reliable quality and repeatability of assembly No over-driving or under-driving Available painted to match any panel color AP16 Rivet Attach high-performance cladding panels to aluminum or steel sub-frames Drilling capacity: Material: Body: Aluminum AlMg5 Mandrel: Stainless Steel A3 2.7 (0.11 ) 16 (0.63 ) 1.5 (0.06 ) 5 (0.19 ) Nom. Tensile: 3720 N (836 lbs.) Pull-out Strength - Extruded Aluminum Pull-out Strength - 33 KSI Yield Sheet Steel Nom: Shear: 2410 N (542 lbs.) AIMg 1.8mm (.071 ): 2410 N (542 lbs) 22 ga. (030 ): 1210 N (272 lbs.) 18 ga. (.048 ): 2360 N (530 lbs.) Notes: Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safety factors applied when specifyng the proper fasteners. Pull-out strength values obtained with 5.1 mm (0.201 ) pre-drill. Description Part No. Global Code Grip Range 5 X 16mm AP S mm ( ") 5 X 18mm AP S mm ( ") 5 X 21 mm AP S mm ( ") Installation 5.1mm (0.201 ) pilot hole required in aluminum framework for fixed point. All other holes depend on material. Check the attachment method instructions provided by the cladding panel manufacturer. Options irius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

38 Architectural Fasteners TU-S Blind Fastener Fastening HPL cladding panels Enables brackets, straps or clips to be attached quickly and securely to the back of HPL cladding panels Cost-effective Installation can be performed by one person No special tools required Can be installed into panels 8mm to 13mm (.31 to.51 ) thick TU-S Blind Fastener Fasten brackets, straps or clips to the back of panels Material: Sleeve: Stainless steel (grade 316, DIN ) 3.3 (0.13 ) 6 (0.24 ) Mandrel: Carbon steel (is pulled off completely, i.e. no residue remains) 8 (0.31 ) Notes: Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safety factors applied when specifyng the proper fasteners. Description Part No. Global Code Bracket Range Panel Range 6 X 11mm TU-S-6X ( ") 8-13 mm ( ") 6 X 13mm TU-S-6X ( ") mm ( ") Installation Pre-drill pilot hole a minimum of 6.5mm deep and 6.0mm diameter. Residual panel thickness must be at a minimum of 1.5mm; check panel manufacturer s specific requirements. Insert fastener by hand through bracket into pre-drilled pilot hole; remove the mandrel with riveting tool. Utilize HSS blind hole drill bit, 6mm (0.236 ) diameter, with depth stop Bracket or clips requires a 7 mm (0.276 ) clearance hole An appropriate washer is required with thinner brackets.

39 Architectural Fasteners GAZ Design Elements Exposed fastening effects for cladding attachment GAZ Design Elements fasteners are a two-part fastening system. The 304SS anchor secures cladding to timber, steel or aluminum subframes. The design element cap is then effortlessly assembled on to the special fastener after installation. GA #14 Type A Anchor 300 series stainless steels provides maximum corrosion resistance Design elements available in a choice of colors and fascinating effects Creates special emphasis on internal or external surfaces Secure against unwinding through dynamic loads. Cannot be removed manually after curing. SW 9.5 (0.38 ) Material: Fastener: 304SS Sealing Washer: SS with vulcanized EPDM 6.5 (0.26 ) 45 (1.77 ) GA #14 Type B Anchor SW 9.5 (0.38 ) Material: Fastener: 304SS Sealing Washer: SS with vulcanized EPDM 6.3 (0.25 ) 32 (1.26 ) GAZ Design Element Caps Available in 316 Stainless Steel, 303 Stainless Steel or anodized aluminum Available in the following colors: Stainless Steel: Mill finish, 40 maximum surface roughness Aluminum: red, blue, green, black, gold, silver x x x x 1.26 Part No. Description Global Code Anchors x 1-1/4 Type A Stainless Steel Anchor GA-AS-S16-6,5X x 1-3/4 Type A Stainless Steel Anchor GA-AS-S16-6,5X x 1-1/4 Type B Stainless Steel Anchor GA-BS-S16-6,3X32 GAZ Design Elements Stainless Steel Cap GAZ-801-S Stainless Steel Cap GAZ-804-S Stainless Steel Cap GAZ-806-S Stainless Steel Cap GAZ-807-S Stainless Steel Cap GAZ-811-S Anodized Aluminum Cap GAZ Anodized Aluminum Cap GAZ Anodized Aluminum Cap GAZ Anodized Aluminum Cap GAZ Anodized Aluminum Cap GAZ x 1.26 Installation E395 special socket avaiable.

40 Metal to Wood Woodgrip Fasteners Woodgrip is the original sheet to wood fastener designed to self-drill metal panels: High Hex Washer Head provides driving stability and a sharp point for quick installation. Assembled with a control seal washer for a consistent, weather tight seal and improved installation appearance. Extended corrosion resistant coating system. Woodgrip XG is a sheet to wood fastener designed to self drill metal panels: Superior performance in OSB, plywood and 1x4 pine. Superior resistance to stripout Extra aggresive thread design. Improved pullout and backout values over other wood screws by as much as 30%. Extended corrosion resistant coating system. Woodgrip # 14 Type A mill point carbon steel self-tapping fasteners are designed for attaching both metal to wood and metal to metal: These fasteners do not require a pre-drilled hole when attaching 26 and 24 gage metal to wood. Corrosion resistant coating system. Woodgrip 9 15 HWH Sharp Point Assembled with Control Seal Metal to wood Drilling capacity: 24 ga (.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1" HiLo Woodgrip Assembled Bond Seal washer Metal to wood Drilling capacity: 24 ga (.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1" Woodgrip, HiLo Woodgrip, Woodgrip XG, Woodgrip #14 Type A MP, Low Profile Woodgrip For metal to wood HiLo Woodgrip is a sheet to wood fastener designed to self-drill metal panels: High Hex Washer Head provides driving stability and a milled point for quick installation. Assembled with a bond seal washer for a consistent, weather tight seal and improved installation appearance. Extended corrosion resistant coating system. Low Profile Woodgrip is a sheet to wood fastener designed to self-drill metal panels: Low profile head for pleasing appearance. Mill point ensures great drill performance. HiLo thread with added pull-out resistance. Available with bond seal for exterior sidewall application or no washer for interior applications. Corrosion resistant coating system. 1/4" Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933 1/4" Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933 Woodgrip XG 12 8 HWH Sharp Point Assembled with Control Seal Metal to wood Drilling capacity: 24 NEGATIVE ga (.024) reduced 00% Self-drills through the metal panel and taps into wood substrate. Large, aggressive thread design provides superior resistance to strip-out, and superior performance in OSB, plywood, and 1x4" pine. Min penetration in wood substrates should be no less than 1" Notes Dimensions are nominal inches unless noted. File Name: WG6.1_C0261.eps Created by: EWB-11/27/02 1/4" Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 2183 Torsional: 60 in-lbs min. Shear: 1946 Continued on following page

41 Metal to Wood Woodgrip 12 x 3/4 Lap Assembled Bond Seal washer Drilling capacity: 2 x 24 ga Panel to panel side lap, end lap and other stitch applications Woodgrip Fasteners Woodgrip, HiLo Woodgrip, Woodgrip XG, Woodgrip #14 Type A MP, Low Profile Woodgrip For metal to wood 1/4" Hex Washer Head: Thread Major Dia: Thread Minor Dia: Tensile: 2100 Torsional: 92 in-lbs min. Shear: 1800 Woodgrip HiLo Low Profile Exterior Sidewall Fastener, Bond Seal Drilling capacity: 24 ga. (.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1" T25 TORX Pan Head: Thread Major Dia: Thread Minor Dia: Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933 Woodgrip HiLo Low Profile Interior Liner Panel, NEGATIVE No reduced Washer 00% Drilling capacity: 24 ga. (.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1" File Name: WG6.1_A1701.eps Created by: EWB-11/27/02 T25 TORX Pan Head: Thread Major Dia: Thread Minor Dia: Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933 Available painted white only. #14 Type A Milled Point Carbon Steel, Silver Sentri Metal to wood Self-drilling metal thickness: Sheet Thickness is based on normal, single or multiple material thickness combined for total. Min depth penetration into the wood sub structure: 1" 5/16" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3500 Torsional: 125 in-lbs Shear: 2400 Notes Dimensions are nominal inches unless noted. NEGATIVE reduced 00% File Name: WG6.4_A3321.eps Created by: EWB-11/27/02 Continued on following page

42 Metal to Wood Woodgrip Fasteners Performance Pounds Ultimate Pull-out (lbs ult.) Wood: Spruce, Pine, Fir #9 Woodgrip Control Seal Washer 1-1/2" Penetration 748 1" Penetration 542 #10 HiLo Woodgrip Bond Seal Washer 1-1/2" Penetration 820 1" Penetration 524 #10 HiLo Torx Pan Head Woodgrip 1-1/2" Penetration 820 1" Penetration 524 #14 Type A Milled Point 1" Penetration 1013 Woodgrip, HiLo Woodgrip, Woodgrip XG, Woodgrip #14 Type A MP, Low Profile Woodgrip For metal to wood Pull-over 29 ga (110 ksi): ga (70 ksi): ga (70 ksi): ga (110 ksi): ga (70 ksi): ga (110 ksi): ga (70 ksi): ga (70 ksi): ga (.030): ga (.024): ga (.018): 564 Pull-out (lbs ult.) % Increase Strip-out vs. Woodgrip (in-lbs) #12 Woodgrip XG Control Seal Washer SPF 1-1/2" Penetration SPF 1" Penetration x4" Pine /4" Plywood /8" Plywood /2" Plywood /32" OSB /32" OSB Notes: Woodgrip and HiLo pull-out strength values may vary from tested loads depending upon specific wood density variations. Woodgrip and HiLo pull-over strength values are based on.035" thick, ½" OD Control Seal or Bond Seal washer and have been updated to reflect common tensile strengths of metal panels as a function of panel thicknesses. TORX pan head HiLo pull-out strength values may vary from tabulated loads depending upon specific wood density variations. Pull over strength values are based on ½" nominal OD TORX head and AZ55 Galvalume steel material. Pull-over 29 ga (110 ksi): ga (70 ksi): ga (70 ksi): 800 Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failure over time. This may be due to the fasteners being stripped out during installation and/or due to the lack of adequate wood fiber material to hold the fastener in place during thermal movement cycles or other forces which may be exerted upon the connection. Percent increase strip-out values of the Woodgrip XG over the standard Woodgrip are typical results, as encountered when fasteners are installed at 2500 rpm until full strip-out occurs. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fastener. Size Woodgrip HiLo Woodgrip Woodgrip XG Exterior Low Profile Interior Liner Panel #14 A Milled Point 1" V0161-CCF V1008-CDF V1806-EMF A0408-CFF A F V3321-GBF 1-1/2" V0261-CCF V1012-CDF V1841-EMF A0412-CFF V3438-GBF 2" V0381-CCF V1016-CDF V1851-EMF A0416-CFF V3531-GBF 2-1/2" V0461-CCF V1020-CDF V1856-EMF A3597-GBF 3" V0485-CCF V1024-CDF V1861-EMF A3626-GBF 12 x 3/4" (1/4" HWH) V1701-ECF V1707-EAF Installation Options Stainless Tools: rpm screw driver equipped ZAC with MAC Prisma irius VistaCoat Painted Painted ZAC ZAC Sentri MAC MAC SX PrismaBI- Self Drilling depth sensing nose piece. ZAC MAC PRISMA irius ZAC ZAC MAC PRISMA

43 Metal to Wood EVERGRIP 300 Series Stainless Fasteners EVERGRIP stainless bi-metal For metal to wood EVERGRIP stainless wood fastener is designed to self-drill metal panels: Head and the majority of shank is 300 Series Stainless Steel, with a welded, hardened carbon steel point for self-drilling performance. Provides the corrosion protection of stainless with the drill performance of a carbon steel fastener. Designed specifically for superior corrosion resistance in all wood treatments. Available with HWH or TORX drive pan head. EVERGRIP 9 15 HWH Sharp Point Assembled with stainless Bond Seal Metal to wood Drilling capacity: 24 ga (0.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1" 1/4" Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 1657 Torsional: 50 in-lbs min. Shear: 1550 EVERGRIP 9 15 T-25 (TORX ) Pan Head Assembled with stainless Bond Seal Metal to wood Drilling capacity: 24 ga. (0.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1" NEGATIVE reduced 00% File Name: WG6.3_E4160.eps Created by: EWB-11/27/02 T-25 (TORX) Pan Head Head Dia: Thread Major Dia: Thread Minor Dia: Tensile: 1657 Torsional: 50 in-lbs min. Shear: 1550 Utilizing the special SFS T-25 Torx drive bit manufactured by SFS intec is recommended for superior stability during the installation process. Performance Pounds Ultimate NEGATIVE reduced 00% Pull-out (lbs ult.) Wood: Spruce, Pine, Fir EVERGRIP Stainless Bond Seal 1-1/2" Penetration 748 1" Penetration 542 File Name: P_1481A_E.eps Created by:ewb-04/8/08 Revised: MPD-00/00/08 Pull-over 29 ga: ga: ga: 704 Notes: Dimensions are nominal inches unless noted. Pull out strength values may vary from tabulated loads depending upon specific wood density variations. Pull over strength values are based on AZ55 Galvalume steel material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied. Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failure over time. This may be due to the fasteners being stripped out during installation and/or due to the lack of adequate wood fiber material to hold the fastener in place during thermal movement cycles or other forces which may be exerted upon the connection. Installation HWH HWH T-25 Pan Head Tools: rpm screwdriver equipped Length 250/Bag 100/Box 250/Bag with depth sensing nosepiece. 1" E4160-CUF E4160-CUEG The EVERGRIP 9-15 T-25 (TORX) Pan Head 1-1/2" E4260-CUF E4260-CUEG ZAC MAC requires a T-25 PRISMATorx drive bit. irius 2" E4380-CUF E4380-CUEG Utilizing the special SFS T-25 Torx drive 2-1/2" E4460-CUF E4460-CUEG bit manufactured by SFS intec is 3" recommended for superior stability during the installation process. Description Part No. Quantity SFS Special T-25 Torx drive bit each Options ZAC MAC Prisma irius Painted Sentri SX Painted

44 Metal to Wood 300 Series Stainless Aluminum Panel Woodgrip Woodgrip stainless For aluminum panel Stainless, Aluminum Panel Woodgrip is an all stainless wood fastener designed for use with aluminum panels: Fastener is 304 stainless steel for corrosion protection. High hex washer head provides driving stability and a sharp point for quick installation into aluminum. Will not drill steel panels. Stainless Aluminum Panel Woodgrip 9 15 HWH Sharp Point Assembled with aluminum Bond Seal Metal to wood Self-drills through aluminum panel and taps into wood substrate. Min penetration in wood substrate should be no less than 1" 1/4" Hex Washer head Thread Major Dia: Thread Minor Dia: Tensile: 1657 Torsional: 50 in-lbs min Shear: 1550 Performance Pounds Ultimate Pull-out (lbs ult.) Wood: Spruce, Pine, Fir #9 Woodgrip Stainless Aluminum Bond Seal 1-1/2" Penetration 748 1" Penetration 542 Notes: Dimensions are nominal inches unless noted. Pull out strength values may vary from tabulated loads depending upon specific wood density variations. The specific job conditions should be considered and appropriate safety factors applied. Stainless Woodgrips are not designed to self-drill steel panels. Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failure over time. This may be due to the fasteners being stripped out during installation File and/or Name: due WG6.3_E0270.eps to the lack of adequate wood fiber material NEGATIVE to hold reduced the 00% fastener in place during thermal movement cycles or Created other forces by: EWB-11/27/02 which may be exerted upon the connection. Size Stainless Woodgrip 1" E0225-CKF 1-1/2" E0270-CKF 2" E0272-CKF 2-1/2" E0275-CKF 3" E0277-CKF Installation Tools: rpm screwdriver equipped with depth sensing nosepiece. Options irius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

45 Metal to Wood Woodgrip Capped Fasteners WoodZAC and WoodMAC For metal to wood WoodZAC has all the performance features of standard Woodgrip fasteners, plus a zinc alloy cap that can never red rust: 5/16" AF high Hex Washer Head for driving stability and a sharp point for quick installation. Assembled with a aluminum bond seal for weather tight seal and improved installation appearance. HiLo WoodZAC HWH Mill Point Assembled with aluminum Bond Seal Metal to wood Drilling capacity: 24 ga (.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1" WoodMAC has all the performance features of standard Woodgrips: 1/4" AF 300 series stainless capped HWH for a low profile head appearance that can never rust. 5/16" Hex Washer Head Zinc Alloy Cap Thread Major Dia: Thread Minor Dia: Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933 WoodZAC XG 12 8 HWH Sharp Point Assembled with EPDM washer Metal to Wood Drilling capacity: 24 ga (.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1" WoodZAC 12 x 3/4" LAP Sharp Point Assembled with EPDM washer Panel to panel side lap, end lap and other stitch applications 5/16" Hex Washer Head Zinc Alloy Cap Thread Major Dia: Thread Minor Dia: Tensile: 2183 Torsional: 60 in-lbs min. Shear: /16" Hex Washer Head Zinc Alloy Cap Thread Major Dia: Thread Minor Dia: Tensile: 2100 Torsional: 92 in-lbs min. Shear: 1800 #14 ZAC Type A Milled Point Metal to wood Self-drilling metal thickness: Sheet Thickness is based on normal, single or multiple material thickness combined for total. Min depth penetration into the wood sub structure: 1" NEGATIVE reduced 00% File Name: WG6.2_A1705.eps Created by: EWB-11/27/02 3/8" AF Zinc Alloy Capped Thread Major Dia: Thread Minor Dia: Tensile: 3500 Torsional: 125 in-lbs Shear: 2400 Notes Dimensions are nominal inches unless noted. Continued on following page

46 Metal to Wood Woodgrip Capped Fasteners WoodZAC and WoodMAC For metal to wood 1/4 ZAC Type AB Milled Point Metal to metal Metal to wood Self-drilling metal thickness: Sheet Thickness is based on normal, single or multiple material POSITIVE reduced thickness 00% combined for total. Min depth penetration into the wood sub structure: 1" WoodMAC 9 15 HWH Sharp Point Assembled with EPDM washer Metal to wood Drilling capacity: 24 ga (.024) Self-drills through the metal panel and taps into wood substrate. Min penetration in wood substrates should be no less than 1" NEGATIVE reduced 00% WoodMAC Lap 12 x 3/4" HWH Sharp Point Assembled EPDM washer Panel to panel side lap, end lap and other stitch applications NEGATIVE reduced 00% File Name: WG6.2_C0268.eps Created by: MPD-12/02/02 File Name: WG6.4_A4395.eps Created by: EWB-11/27/02 3/8" AF Zinc Alloy Capped Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 142 in-lbs Shear: /4" Cupped Stainless Capped Thread Major Dia: Thread Minor Dia: Tensile: 1500 Torsional: 60 in-lbs min. Shear: 933 1/4" Cupped Stainless Capped Thread Major Dia: Thread Minor Dia: Tensile: 2100 Torsional: 92 in-lbs min. Shear: 1800 Notes: Dimensions are nominal inches unless noted. Performance Pounds Ultimate Pull-out (lbs ult.) Wood: Spruce, Pine, Fir #10 HiLo Woodgrip 5/16" ZAC Aluminum Bond Seal 1-1/2" Penetration 820 1" Penetration 524 #9 Woodgrip 1/4" MAC EPDM Washer 1-1/2" Penetration 748 1" Penetration 542 NEGATIVE reduced 00% #14 A Milled Point 3/8" ZAC 1" Penetration /4" AB Milled Point 3/8" ZAC 1" Penetration 1013 File Name: WG6.2_A1708.eps Created by: EWB-11/27/02 Pull-over 29 ga: ga: ga: ga: ga: ga: ga: ga: ga: ga: ga: ga: 1094

47 Metal to Wood Woodgrip Capped Fasteners WoodZAC and WoodMAC For metal to wood Pull-out (lbs ult.) Strip Out* (in lbs) Pull-over #12 WoodZAC XG EPDM Washer SPF 1-1/2" Penetration ga (110 ksi): 577 SPF 1" Penetration ga (70 ksi): x 4" Pine ga (70 ksi): 800 3/4" Plywood /8" Plywood /2" Plywood /32" OSB /32" OSB * Strip-out values were determined by the dynamic strip-out test, wherein fasteners were driven though a 24 gage panel into the applicable substrate at 2500 rpm until stripout occured. The strip-out values listed above represent the average maximum strip-out measured by the digital data acquisition system when the fastener was driven into the given substrate. Notes: Woodgrip and WoodZAC pull out strength values may vary from tabulated loads depending upon specific wood density variations. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failure over time. This may be due to the fasteners being stripped out during installation and/or due to the lack of adequate wood fiber material to hold the fastener in place during thermal movement cycles or other forces which may be exerted upon the connection. Size HiLo WoodZAC WoodZAC XG WoodZAC WoodMAC WoodMAC #14 A Milled Point #14 AB Milled Point Lap Lap 3/8" ZAC 3/8" ZAC 1" A1066-DNF A1807-FCF C0168-CAF A3325-FMF A4395-FMF 1-1/4" A4428-FMF 1-1/2" A1071-DNF A1842-FCF C0268-CAF A4485-FMF 2" A1076-DNF A1852-FCF C0388-CAF A4513-FMF 2-1/2" A1081-DNF A1857-FCF C0468-CAF A4510-FMF 3" A1086-DNF A1862-FCF C0488-CAF 12 x 3/4" ZAC (5/16" HWH) A1705-FLF 12 x 3/4" MAC (1/4" HWH) A1708-EYF Installation Tools: Tools: Metal to metal application: rpm screwdriver equipped with depth sensing nosepiece. Metal to wood application: rpm screwdriver equipped with depth sensing nosepiece. Options a irius Painted Sentri SX Self Drilling BI-METAL VistaCoat Painted Stainless MA irius ?

48 Panelmaster Fastening System (RH2) Product Panelmaster Name: #14 (RH3) Description: Collated belted #3 Phillips fasteners Drive (RH4) : For Post Frame Insulation Metal board Panel to Attachment roof cover. Increased speed of installation Improved working ergonomics Stand-up roof attachment Fasteners installed uniformly every time Special footpieces available for attachment through the panel rib Installs fasteners 1" 3" long Panelmaster Tool Kit Standard tool kit includes: Panelmaster tool DeWalt 18V drive unit Battery charger and extra battery One extension piece Extra drive bits Corded DeWalt drive unit available One-year full replacement warranty Belted Fasteners SFS intec fasteners 1" through 3" lengths with sealing washers Can be painted to match any panel color All fasteners packaged 500 per carton Woodgrip Fasteners Item Length SFS Part # Woodgrip 9 15 HWH Control Seal Washer VistaCoat HiLo Woodgrip HWH Bond Seal Washer VistaCoat Woodgrip XG HWH Bond Seal Washer VistaCoat 1" V0161-CCBL 1-1/2" V0261-CCBL 2" V0381-CCBL 2-1/2" V0461-CCBL 3" V0485-CCBL 1" V1008-CDBL 1-1/2" V1012-CDBL 2" V1016-CDBL 2-1/2" V1020-CDBL 3" V1024-CDBL 1" V1806-EMBL 1-1/2" V1841-EMBL 2" V1851-EMBL 2-1/2" V1856-EMBL 3" V1861-EMBL Long-Life Fasteners Item Length SFS Part # WoodMAC 9-15 HWH Seal Washer VistaCoat Evergrip 9-15 HWH Stainless Bond Seal Washer Evergrip 9-15 Torx Stainless Bond Seal Washer 1" C0168-CABL 1-1/2" C0268-CABL 2" C0388-CABL 2-1/2" C0468-CABL 3" C0488-CABL 1" E4160-CUBL 1-1/2" E4260-CUBL 2" E4380-CUBL 2-1/2" E4460-CUBL 1" " "

49 Panel Clips, Bearing Plates and Fasteners Standing Seam Clips Engineered panel clips For standing seam panel attachments Engineered panel clips are custom designed and manufactured for your panel system. Clips are supplied in galvanized steel, coated steel, stainless steel and other materials. Engineered fixed and float clip designs are available. - Snap Lock Snap Lock Panel Design Configurations require very low profile clip bases with a base feature to hold the panel above the low profile fastener heads. 1" Snap Lock Clip G90 Galvanized: 18 ga. Packaged 200 per carton Roof Panel Blanket Insulation Clip Roof Panel Low Profile Head Fastener Roof Purlin Standard clips are available from stock without tooling cost to you. Sealant can be pre-applied to the clips to maintain the seal at the clip attachment. Clip design options are available for review and evaluation. All clips also available in stainless steel. Fixed Clips are primarily used with these panels. Low profile head fasteners should be used with these panels to provide clearance for the panel over the fastener heads. These clips are manufactured from steel, stainless steel and other materials with various finishes to fit the needs of the panel application. 1-1/2" Snap Lock Clip G90 Galvalume: 24 ga. Packaged 1000 per carton Roof Panel Blanket Insulation Clip Roof Panel Low Profile Head Fastener Roof Purlin 1-1/2" Snap Lock G90 Galvanized: 18 ga. or 20 ga. Packaged 500 per carton 1-1/2" Snap Lock Clip G90 Galvanized: 18 ga. Packaged 125 per carton 1-5/8" Snap Lock (3 hole) Clip G90 Galvanized: 18 ga. Packaged 500 per carton 1-3/4" Snap Lock (2 hole) Clip G90 Galvanized: 18 ga. Packaged 250 per carton 1-3/4" Snap Lock (1 hole) Clip G90 Galvanized: 18 ga. Packaged 500 per carton 1-3/4" Snap Lock (3 hole) Clip G90 Galvanized: 20 ga. Packaged 500 per carton Continued on following page

50 Panel Clips, Bearing Plates and Fasteners Standing Seam Clips Engineered panel clips For standing seam panel attachments - Snap Lock BattenTrim (spider) Clip 304SS (1/4 Hard): 22 ga. Packaged 500 per carton - Architectural/Mechanical Architectural/Mechanical Panel Design Configurations require low profile bases with clearance for the fastener head. Sliding Clip Assembly Roof Panel Roof Panel Roof Purlin Fixed and Float Clips are used with these panels. The clips may have pre-applied sealant to maintain the panel seal at the clip attachment point. These clips are manufactured from steel, stainless steel and other materials with various finishes to fit the needs of the panel application. Sliding Clip Assembly Roof Panel Roof Panel Roof Purlin Blanket Insulation Blanket Insulation 1-1/2" Fixed Clip (.38 Hor.) G90 Galvanized: 22 ga. Packaged 250 per carton 1-1/2" Fixed Clip (.43 Hor.) G90 Galvanized: 24 ga. Packaged 350 per carton 2" Fixed Clip (.57 Hor.) G90 Galvanized: 22 ga. Packaged 250 per carton 2" Fixed Clip (.70 Hor.) G90 Galvanized: 22 ga. Factory applied sealant Packaged 400 per carton 2" Fixed Clip (.70 Hor.) G90 Galvanized: 22 ga. Packaged 400 per carton 2-3/8" Fixed Clip (.66 Hor.) G90 Galvanized: 22 ga. Packaged 200 per carton 2-3/8" Fixed Clip (.70 Hor.) G90 Galvanized: 22 ga. Factory applied sealant Packaged 250 per carton 2-3/8" Fixed Clip (.70 Hor.) G90 Galvanized: 22 ga. Packaged 250 per carton

51 Panel Clips, Bearing Plates and Fasteners Standing Seam Clips Engineered panel clips For standing seam panel attachments - Architectural/Mechanical 3" Fixed Clip (.66 Hor.) G90 Galvanized: 22 ga. Packaged 200 per carton 3" Fixed Clip (.70 Hor.) G90 Galvanized: 22 ga. Packaged 250 per carton 3" Fixed Clip (.935 Hor.) G90 Galvanized: 22 ga. and 24 ga. Packaged 250 per carton 3" Fixed Clip (.70 Hor.) G90 Galvanized: 22 ga. Factory applied sealant Packaged 250 per carton 1-1/2" Float Clip (.65 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Factory applied sealant Packaged 100 per carton 1-1/2" Float Clip (.38 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 80 per carton 1-1/2" Float Clip (.71 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 100 per carton 2" Float Clip (.57 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 80 per carton 2" Float Clip (.70 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Factory applied sealant Packaged 100 per carton 2" Float Clip (.66 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Factory applied sealant Packaged 80 per carton 2" Float Clip (.70 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Factory applied sealant Packaged 100 per carton 2" Float Clip (.70 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Factory applied sealant Packaged 100 per carton Continued on following page

52 Panel Clips, Bearing Plates and Fasteners Standing Seam Clips (RH3) Description: Engineered #3 Phillips panel Drive clips (RH4) : For standing Insulation seam board panel to attachments roof cover. - Architectural/Mechanical 2" Float Clip (.71 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 60 per carton 3" Float Clip (.70 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Factory applied sealant Packaged 100 per carton 3" Float Clip (.66 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Factory applied sealant Packaged 60 per carton 3" Float Clip (.70 Hor.) G90 Galvanized: 22 ga. Tab Base: 16 ga. Factory applied sealant Packaged 100 per carton 3-3/8" Float Clip (.71 Hor.) For 2" Panel G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 70 per carton 4-3/8" Float Clip (.71 Hor.) For 3" Panel G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 60 per carton 3-3/8" Float Clip (.71 Hor.) For 3" Panel G90 Galvanized: 22 ga. Tab Base: 16 ga. Packaged 80 per carton Continued on following page

53 Panel Clips, Bearing Plates and Fasteners Standing Seam Clips Engineered panel clips For standing seam panel attachments - Architectural/Mechanical Butterfly Tab 1-1/2" G90 Galvanized: 22 ga. Packaged 200 per carton Butterfly Base 1-1/2" G90 Galvanized: 22 ga. Packaged 200 per carton Butterfly Tab 2" G90 Galvanized: 22 ga. Packaged 150 per carton Butterfly Base 2" G90 Galvanized: 18 ga. Packaged 150 per carton Continuous Base 1-1/2" or 2" 1-1/2" G90 Galv.: 22 ga. 1-1/2" Packaged ft pieces per carton 2" G90 Galv.: 18 ga. 2" Packaged ft pieces per carton

54 Panel Clips, Bearing Plates and Fasteners Snap Lock and Universal Bearing Plates Bearing Plates For standing seam panel attachments Unique design fits most standing seam clips Hole spacings can be customized to meet customer requirements Produced in ga. materials Available in various dimensions - Bearing Plates Snap Lock Bearing Plate Dimension 4.75" x 6" 24 ga. G-90 Galv. Packaged 125 per carton Universal Bearing Plate Dimension: 4" x 6" or 4" x 5" 18, 20, 22 and 24 ga. G-90 Galv. Packaged 125 per carton

55 NEGATIVE reduced 00% File Name: WG8.2_A1187.eps Created by: EWB-11/27/02 Panel Clips, Bearing Plates and Fasteners Clip Fasteners Clip attachment fasteners For metal to metal, metal to wood Designed with unique head styles, drill point configurations and material types to meet performance requirements to attach standing seam roof clips. #10 Type A: Pancake Head 2/2 Quadrex Drive Carbon Steel, Zinc Plated Metal to wood #10 Type A: Pancake Head Phillips Drive 300 Series Stainless Steel Metal to wood #10 Self-Drill: Pancake Head 2/2 Quadrex Drive Carbon Steel, Zinc Plated Metal to metal Min projection: POSITIVE 3/8" of reduced threads 00% below substrate #12 8 XG Sharp Point: Pancake Head 2/2 Quadrex Drive Carbon Steel, Zinc Plated Metal to wood NEGATIVE reduced 00% NEGATIVE reduced 00% #12 Type A: Pancake Head 2/2 Quadrex Drive Carbon Steel, Zinc Plated Metal to wood #12 Self-Drill: Pancake Head 2/2 Quadrex Drive Carbon Steel, Zinc Plated Metal to metal Min projection: 3/8" of threads below substrate. Roof Panel Blanket Insulation Clip Engineered profile features preventing panel damage from fastener head contact. Engineered installation torque drive control for uniform installation performance. Roof Panel Low Profile Head Fastener Roof Purlin File Name: WG8.2_A1187.eps Created by: EWB-11/27/02 File Name: WG8.2_S3450.eps Created by: EWB-11/27/02 Head Height: Head Dia: Thread Major Dia: Thread Minor Dia: Carbon Stainless Tensile: Torsional: 48 in-lbs 50 in-lbs Shear: #10 Type A, Pull-out (lbs ult.): SPF wood: 1" penetration: 821 #10 Self Drill, Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 782 Head Height: Head Dia: Thread Major Dia: Thread Minor Dia: Tensile: 2183 Torsional: 60 in-lbs Shear: 1946 Performance (lbs ult.): Pull-out SPF 1-1/2" Penetration 874 SPF 1" Penetration 571 1x4" Pine 590 3/4" Plywood 587 5/8" Plywood 446 1/2" Plywood /32" OSB /32" OSB 456 Head Height: Head Dia: Thread Major Dia: Thread Minor Dia: Tensile: 1940 Torsional: 90 in-lbs Shear: 1805 Pull-out (lbs ult.): SPF wood: 1" penetration: 724 Head Height: Head Dia: Thread Major Dia: Thread Minor Dia: Tensile: 2900 Torsional: 92 in-lbs Shear: 2050 Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): 724 Continued on following page

56 Panel Clips and Fasteners Clip Fasteners Clip attachment fasteners For metal to metal, metal to wood 1/4-14 #2 Point Drilling capacity (#2 point): Attachment thickness: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8" of threads below substrate Roof Panel Blanket Insulation Roof Panel Clip Roof Panel Roof Purlin 5/16" AF Hex Washer Head 3/8" AF Hex Washer Head Thread Major Dia: Thread Minor Dia: Tensile: 3800 Torsional: 150 in-lbs Shear: 2850 #2 Point, Pull-out (lbs ult.): 12 ga (.105): ga (.075): ga (.060): #5 Point: Pancake Head 2/2 Quadrex Drive Carbon Steel, Zinc Plated Metal to metal Drilling capacity: Attachment thickness: Thickness is based on normal, single thickness purlin/girt or multiple material thickness combined for total. Min projection: 3/8 of threads below substrate NEGATIVE reduced 00% File Name: WG(7.2)_S5271_14_14Impax.eps Created by: EWB-12/12/02 Head Height: Head Dia: Thread Major Dia: Thread Minor Dia: Tensile: 3450 Torsional: 100 in-lbs Shear: 2420 Pull-out (lbs ult.): 12 ga (.105): /16" (.187): Exceeds tensile value 1/4" (.250): Exceeds tensile value Notes Dimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners. Fasteners installed in less than 1" of solid wood may have an increased potential for a connection failure over time. This may be due to the fasteners being stripped out during installation and/or due to the lack of adequate wood fiber material to hold the fastener in place when forces are exerted upon the connection. Length #10 Type A Pancake Carbon Steel #10 Type A Pancake Stainless Steel #10 Self-Drill Pancake #12 8 XG Pancake #12 Type A Pancake #12 Self-Drill Pancake #5 Point Pancake Installation Tools: rpm #10 self drill, rpm on 1/4-14 self drill screwdriver equipped with depth sensing nosepiece. 1/4 14 #2 Point 5/16 AF HWH 1/4 14 #2 Point 3/8 AF HWH 1" A1191F E0235F S3431F A1900F A1710F S4552F S5171F 1-1/4" S5191F 1-1/2" A1351F S4221F A1940F S4750F S5286F S5271F 2" A1391F E0271F S4421F A1950F

57 Attachment Solutions AceClamp Attachment Solution for Standing Seam Roofs Fast - No assembly required Easy - One top-mount fastener Secure - Locks in place AceClamp ML Fits Mechanical Lock panels Attachment Solution for: solar HVAC snowrails conduit windclamps signs Single Lock Double Lock T-Seam Z-Rib AceClamp SL Fits - Snaplock panels - Mechanical Lock panels with seam dimension of.500" Snaplock Mechanical Lock (small seam) Notes AceClamp is not designed for use on batten seam panel systems and is not recommended for nail flange panel systems. AceClamp is not to be used as any part of a fall protection system. For all applications, determining the suitability of the product and the installation orientation relative to the seam are the responsibility of the professional design engineer. Model Part # Packaging AceClamp ML per box/5 boxes per case AceClamp SL per box/5 boxes per case Drive Bit Installation Tools: 1/4" hex driver (bit # ). Finish tightening with calibrated torque wrench.

58 .7" Attachment Solutions SOL-R Solar Fastening System for exposed fastener metal roofs Fast, Easy, Secure Installs quickly Rapid adjustment UV resistant, corrosion-free Eliminates conductivity Specifications SOL-R Dimensions Material Docking device.3" 1.18" System components of metal substitute Polyphthalamide (PPA) with 50% glass fiber reinforcement A2/AISI 304 stainless steel bolt for height and position adjustment Aluminum reinforcement plates on the base plate Pre-assembled butyl sealant on the base plate Cap Base plate flexible height adjustment 2" min. height 2.5" max. height 4.5" 4.8" 4.41" 1.65" 1.6".53" Values based on central fastenings Test result is valid for the whole range of the setting position. Compression strength Db Test results refer to the ultimate load required for the component to break when stressed in compression. The force F is applied on the contact surfaces of the component. F x = 846 lb s = 73 lb 3765N 327N Tensile strength Zb Test results refer to the ultimate load required for the component to break when stressed in tension. The force F is applied on the contact surfaces of the component. F x = 505 lb s = 15 lb 2248N 68N Shear strength Qb Test results refer to the ultimate load required for the component to break when stressed in shear. The force F is applied on the contact surfaces of the component. F x = 387 lb s = 23 lb 1724N 104N If the SOL-R docking device is placed in a vertical position, calculate with the following values: Db x = 364 lb 1621N s = 29 lb 130N Zb x = 346 lb 1543N s = 20 lb 89N x = arithmetical mean value s = standard deviation Qb x = 346 lb 1543N s = 20 lb 89N Notes All calculations, measurements, fasteners and design methods have to be verified by a responsible designer or an engineer, regarding the corresponding structure and loads. Please consult local, regional and national codes and approval requirements. Description Part # Packaging SOL-R units/case

59 Blind Rivets and Grommets (RH2) Product Blind Name: Rivets #14 (RH3) Blind Description: rivets attach #3 Phillips light Drive gage (RH4) : Insulation board to roof cover. Many corrosion resistant options Tamper resistant Won't loosen in high vibration or fatigue applications Quality and repeartability of assembly No over-driving or under-driving The installed function of the rivet will be consistent and is independent of the installer's technique Easy to use, lightweight portable installation tools BULB-TITE Rivets BULB-TITE rivets were first developed to solve application requirements in the Pre-Engineered Metal Building industry. Since that time the BULB-TITE product line has been expanded to meet application requirements in a wide range of industries. The BULB-TITE rivet body folds into three seperate legs forming a large blind-side head. This large bearing head evenly distributes the BULB-TITE's clamp force in soft, thin or brittle materials while providing high pull-through resistance. The BULB-TITE's wide grip range enables a single BULB-TITE to work in a greater variation of thicknesses. Aluminum Rivet/Aluminum Mandrel Part No. Part No. Head Style Rivet Diameter No Washer w/ Washer Grip Range Pre-Drill Hole Size Dome Head Protruding Crown 5/32" #20 ( ) Dome Head Protruding Crown 5/32" #20 ( ) Dome Head Protruding Crown 3/16" #4 ( ) Dome Head Protruding Crown 3/16" #4 ( ) Dome Head Protruding Crown 3/16" #4 ( ) Dome Head Protruding Crown 3/16" #4 ( ) Dome Head Protruding Crown 3/16" #4 ( ) Dome Head Protruding Crown 3/16" #4 ( ) Dome Head Protruding Crown 3/16" #4 ( ) Dome Head Protruding Crown 3/16" #4 ( ) Dome Head Protruding Crown 3/16" #4 ( ) Dome Head Protruding Crown 1/4" /4 ( ) Dome Head Protruding Crown 1/4" /4 ( ) Dome Head Protruding Crown 1/4" /4 ( ) Dome Head Protruding Crown 1/4" /4 ( ) Dome Head Protruding Crown 9/32" /16 ( ) Dome Head Protruding Crown 9/32" /16 ( ) Dome Head Protruding Crown 9/32" /16 ( ) Large Flange Prot. Crown 9/32" /16 ( ) Large Flange Prot. Crown 9/32" /16 ( ) Large Flange Prot. Crown 9/32" /16 ( ) Dome Head Recessed Crown 3/16" #4 ( ) Dome Head Recessed Crown 3/16" #4 ( ) Dome Head Recessed Crown 3/16" #4 ( ) Dome Head Recessed Crown 3/16" #4 ( ) Dome Head Recessed Crown 3/16" #4 ( ) Dome Head Recessed Crown 3/16" #4 ( ) Dome Head Recessed Crown 3/16" #4 ( ) Dome Head Recessed Crown 3/16" #4 ( ) Dome Head Recessed Crown 3/16" #4 ( ) Dome Head Recessed Crown 1/4" /4 ( ) Dome Head Recessed Crown 1/4" /4 ( ) Dome Head Recessed Crown 1/4" /4 ( ) Dome Head Recessed Crown 1/4" /4 ( ) Continued on following page

60 Blind Rivets and Grommets Blind Rivets Blind rivets attach light gage MEGA GRIP Rivets The MEGA GRIP is a high strength structural blind rivet offering several advantages over conventional blind rivets. MEGA GRIP's wide grip range enables a single MEGA GRIP to replace up to five different lengths of standard rivets. High shear strength is achieved by MEGA GRIP's flush break self plugging mandrel. MEGA GRIP rivets are hole-filling, resulting in tighter joints and improved sealing for weather resistance. MEGA GRIP rivets are installed via standard rivet tools and do not require special nose tips. Aluminum Rivet/Aluminum Mandrel Head Style Rivet Diameter Part No. Grip Range Pre-Drill Hole Size Dome 3/16" #8 ( ) Dome 3/16" #8 ( ) Dome 1/4" G ( ) Dome 1/4" G ( ) Countersunk 3/16" #8 ( ) Countersunk 3/16" #8 ( ) Countersunk 1/4" G ( ) Countersunk 1/4" G ( ) Large Flange 3/16" #8 ( ) Large Flange 3/16" #8 ( ) Large Flange 1/4" G ( ) Large Flange 1/4" G ( ) Extra Length Metric Rivets SFS intec supplies a complete line of metric blind rivets according to DIN7337 standards in 3mm, 4mm and 5mm diameters. Standard material is Aluminum/Steel. Stainless Steel 304 and 316 alloys are available upon special request. All dimensions for Metric Series are given in millimeters. Additional diameters of 4.8mm, 6mm and 6.4mm available on special request. Aluminum Rivet/Steel Mandrel Head Style Rivet Diameter Part No. Grip Range Pre-Drill Hole Size Dome 3mm Dome 3mm Dome 3mm Dome 3mm Dome 4mm Dome 4mm Dome 4mm Dome 4mm Dome 4mm Dome 4mm Dome 5mm Dome 5mm Dome 5mm Dome 5mm Dome 5mm Dome 5mm Dome 5mm Dome 5mm Dome 5mm Continued on following page

61 Blind Rivets and Grommets Blind Rivets Blind rivets attach light gage PolyGrip Multigrip Blind Rivets PolyGrip rivets feature a wide grip range, enabling a single PolyGrip to replace up to three different lengths of standard blind rivets. PolyGrip rivets expand radially, filling the application hole, resulting in tighter joints and improved sealing. The PolyGrip's locked mandrel core creates a weather resistant fastener. Improved material support is provided by the PolyGrip's larger blindside head formation. Large flange head style available upon request. Stainless Rivet/Stainless Mandrel Head Style Rivet Diameter Part No. Grip Range Pre-Drill Hole Size Dome 1/8" #30 ( ) Dome 1/8" #30 ( ) Dome 1/8" #30 ( ) Dome 5/32" #20 ( ) Dome 5/32" #20 ( ) Dome 5/32" #20 ( ) Dome 3/16" #10 ( ) Dome 3/16" #10 ( ) Dome 3/16" #10 ( ) Aluminum Rivet/Stainless Mandrel Head Style Rivet Diameter Part No. Grip Range Pre-Drill Hole Size Dome 1/8" #30 ( ) Dome 1/8" #30 ( ) Dome 1/8" #30 ( ) Dome 5/32" #20 ( ) Dome 5/32" #20 ( ) Dome 5/32" #20 ( ) Dome 3/16" #10 ( ) Dome 3/16" #10 ( ) Dome 3/16" #10 ( ) Dome 3/16" #10 ( ) Dome 3/16" #10 ( )

62 Blind Rivets and Grommets Blind Rivets Blind rivets attach light gage American Standard Blind Rivets Standard blind rivets are ideally suited for metal trim applications and other light gauge installations. SFS intec provides a selection of 1/8" diameter rivets painted to match standard industry colors. Other sizes and colors available upon request. Aluminum Rivet/Aluminum Mandrel Head Style Rivet Diameter US Dimension Part No. Grip Range Pre-Drill Hole Size Dome 1/8" 42 L #30 ( ) Dome 1/8" 43 L #30 ( ) Dome 1/8" 44 L #30 ( ) Dome 1/8" #30 ( ) Dome 1/8" #30 ( ) Dome 5/32" 52 L #20 ( ) Dome 5/32" 54 L #20 ( ) Dome 5/32" #20 ( ) Dome 5/32" #20 ( ) Dome 3/16" #11 ( ) Dome 3/16" #11 ( ) Dome 3/16" 66 L #11 ( ) Dome 3/16" #11 ( ) Dome 3/16" #11 ( ) Dome 3/16" #11 ( ) Dome 3/16" #11 ( ) Dome 3/16" #11 ( ) Countersunk 1/8" #30 ( ) Countersunk 1/8" #30 ( ) Countersunk 1/8" #30 ( ) Countersunk 1/8" #30 ( ) Countersunk 5/32" #20 ( ) Countersunk 5/32" #20 ( ) Countersunk 3/16" #11 ( ) Steel Rivet/Steel Mandrel Head Style Rivet Diameter US Dimension Part No. Grip Range Pre-Drill Hole Size Dome 1/8" 42 L #30 ( ) Dome 1/8" 43 L #30 ( ) Dome 1/8" 44 L #30 ( ) Stainless Rivet/Stainless Mandrel Head Style Rivet Diameter US Dimension Part No. Grip Range Pre-Drill Hole Size Dome 1/8" 42 L #30 ( ) Dome 1/8" 43 L #30 ( ) Dome 1/8" 44 L #30 ( ) Dome 1/8" 46 L #30 ( ) Dome 1/8" #30 ( ) Dome 5/32" #20 ( ) Dome 5/32" #20 ( ) Dome 5/32" #20 ( ) Dome 3/16" 62 L #11 ( ) Dome 3/16" #11 ( ) Dome 3/16" #11 ( ) Dome 3/16" #11 ( ) White 001 White 014 Bright White 330 Warm White 348 Bone White 818 Sierra White Tan 020 Tan Beige 109 Sand Beige 248 Light Stone 415 Beige 422 Taupe 548 Ivory Brown 110 Brown 230 Desert Brown 374 Dark Brown Green 052 Teal Green 228 Green 232 Evergreen 385 Patina 660 Hemlock 732 Denali Green 798 Hartford Green 925 Classic Green Red 074 Colonial Red 102 Crimson Red 393 Burgundy 691 Barn Red 890 Red 928 Terra Cotta Bronze 042 Burnished Slate 324 Dark Bronze 537 Medium Brown Blue 012 Blue 421 Navy 432 Blue Teal 843 Regal Blue Gray 051 Charcoal Gray 091 Zinc Gray 302 Pearl Gray 416 Slate Gray 578 Old Town Gray 696 Pewter Gray 850 Ash Gray Black 023 Black 507 Matte Black Metallic 1160 Champagne Metallic 1161 Silver Metallic 1162 Zactique Metallic 1116 Copper Penny Metallic

63 Blind Rivets and Grommets Blind Rivet Tools Installation Tools for Blind Rivets AccuBird 14.4 Volt Cordless Riveting Tool Weight: 4.8 lbs. (2.2 kg) Working Stroke:.79" (20 mm) Traction Power: 1,900 lbs. (6,500 N) Power Pack: 14.4 Volt, rechargeable Li-Ion / 1.3 Ah Part Number: Battery Charger: 110V/60Hz, 60 minute charge time PowerBird 14.4 Volt Cordless Riveting Tool Weight: 4.8 lbs. (2.2 kg) Working Stroke:.79" (20 mm) Traction Power: 2,900 lbs. (13,000 N) Power Pack: 14.4 Volt, rechargeable Li-Ion / 2.6 Ah Part Number: Battery Charger: 110V/60Hz, 60 minute charge time RV74G Electric (AC) Powered BULB-TITE Tool The RV74G is the newest refinement in GESIPA Electric Powered BULB-TITE installation tool that is designed for Metal Building Construction applications. This tool is suited to sidewall panel applications. Attaching the optional 74-EXT extension adapts the RV74G for installing BULB-TITE's in roofing applications from a standing position. Work Capacity: 5/32", 3/16", 1/4" & 9/32" BULB-TITE Rivets* *Requires appropriate sized RV8840 series BULB-TITE pulling head. Weight: 6.5 lbs. w/ pulling head attached Length: 14" w/o pulling head, 18" w/ pulling head attached Traction Power: 3,000 lbs. Work Stroke: Continuous reciprocating.375" per cycle Part Number: RV 74-EXT Pulling Head Extension Unit Attachment of the 74 EXT extension unit adapts the RV74G tool for roofing applications. This ergonomic feature enables BULB-TITE installation while standing. Weight: 1.5 lbs. Length: 12-13/16" (Extends tool by 12") Part Number: BULB-TITE Pulling Heads RV8840-X (5,6,8,9 Diameter BULB-TITE Rivets) RV8840 series pulling heads are designed for use with 6603, 8604, 8605 series BULB-TITE rivets which feature multi-grip type mandrels. These heads are equipped with jaws and tips for specific diameter BULB-TITE rivets. The special BULB-TITE crown-swaging nose tip pivots to align the tip onto the BULB-TITE rivet's head crown for improved bore sealing of installed rivets. Specify the BULB-TITE rivet diameter when ordering. Weight: 0.5 lbs. Length: 6 1/16" Part Number: Pulling Head - 5/32" Dia Pulling Head - 3/16" Dia Pulling Head - 1/4" Dia Pulling Head - 9/32" Dia. RV24RE BULB-TITE Removal Tool Designed for use with Aluminum BULB-TITE rivets, the tool greatly simplifies rivet removal in repair operations. The specially ground jaws cut rivet heads off cleanly without damage to the application material. Part Number:

64 Blind Rivets and Grommets Blind Rivet Tools Installation Tools for Blind Rivets Taurus 1 Hydro-pneumatic Power Riveting Tool Nose tips for each rivet diameter are stored in tool's base. Same hydraulic section as the Taurus 2 ensures long tool life and reduced maintenance. Suspension loop retracts into tool body. Work Capacity: 1/8" ø in all materials Weight: 2.87 lbs. Pulling Strength: 1, psi Working Stroke:.590 in. Part Number: Taurus 2 Hydro-pneumatic Power Riveting Tool New 3-piece jaw design increases jaw life reducing service costs. Integrated mandrel collection system with grip release shutoff conserves compressed air resources. Padded ergonomic tool grip enhances comfort lowers operator fatigue. Taurus 3 Hydro-pneumatic Power Riveting Tool Taurus 3 is up to 40% lighter than comparable tools in this power range. Long working stroke installs multi-grip rivets in a single stroke. Reliable exhaust-air mandrel ejection with large collector and saftey interlock. Taurus 4 Hydro-pneumatic Power Riveting Tool Taurus 4 offers the high pulling force required for many of today's 1/4" diameter structural blind rivets. Work Capacity: Up to 3/16" ø in all materials Weight: 3.75 lbs. Pulling Strength: 2, psi Working Stroke:.709 in. Part Number: Work Capacity: Up to 1/4" ø in all materials and 9/32" Alum BT Weight: 4.19 lbs. Pulling Strength: 3, psi Working Stroke:.984 in. Part Number: Work Capacity: Up to 1/4" ø structural blind rivets and 9/32" Alum BT Weight: 4.4 lbs. Pulling Strength: 5, psi Working Stroke:.750 in. Part Number:

65 Blind Rivets and Grommets Grommet Fasteners Grommet fasteners attach fiberglass panels Allow for one side attachment of fiberglass panels through a pre-drilled hole. Designed to pull fiberglass panels together without cracking the material. Come assembled with EPDM washers for a weather tight seal. Grommet Fasteners Materials: Neoprene rubber w/ molded brass nut Size 3/8" Grommet: Part No. E0260-CS Fastener: x 1-1/4" stainless 5/16" AF Hex Head Washer: 15 mm O.D stainless Bond Seal Size 1/4" Grommet: Part No. E0080-CU Fastener: 6-32 x 1-1/4" stainless 1/4" AF Hex Head Washer: 12 mm O.D stainless Bond Seal Notes Dimensions are nominal inches unless noted. Options irius Painted Sentri SX Self Drilling BI-METAL Painted Stainless irius ?

66 Closure and Venting Products WG-7 Closure WG-7 closure and WG-7 adhesive closure For panel opening filler The industry standard for closure material time testedmillions of feet installed over the last 30-plus years. Polyethylene foam for exceptional strength and compressibility. Available with adhesive applied to the contact side of the panel surface assures positive positioning during installation. Resist damaging ultra violet rays and ozone deterioration. Over 1800 panel configurations available. Manufactured in multiple plants for quick delivery. WG-7 Closure Material Thickness: 1", 1-1/2", 2" Color: Black Technical Properties Typical Inside Closure Typical Outside Closure Test Test Method Units Values Density ASTM D3575 lb/ft³ max Working Temperature Range Internal F -76 min 25% 5.1 Compression Deflection 50% ASTM D3575 psi % - 1/2 hr 15 Compression Set 25% - 24 hr ASTM D3575 % max 6 Tear Strength ASTM D3575 psi 11.5 Tensile Strength ASTM D3575 psi 46.8 Elongation ASTM D3575 % 165 Flammability FMVSS302 4"/min Pass Shore Hardness ASTM D2240 OO 55 *Data represents typical values measured on 0.4" thick specimen and should be considered as a guidline only.

67 Closure and Venting Products Pipe Flashing Square and round base pipe flashing For roof pipe flashing Pipe opening can be easily customized on job sight utilizing clearly marked pipe diameters on each flashing. EPDM and Silicone are both flexible materials, resistant to ultraviolet rays, cracking or weathering. Available in EPDM black or gray and silicone red. Square Base Size Pipe size Base size 1 1/4 2-3/4" 4-1/2" Closed Top 2 7/8 4" 6" 3 1/4 5-3/4" 8" Closed Top 4 2-3/4 7" 10" /4" 11" 6 4-3/4 10" 12" 7 5-1/2 11" 14" 8 6-3/4 13-1/2" 17" 9 9-1/2 20-1/2" 25" /2" 34" The aluminum base is corrosion resistant and conforms easily to any panel configuration or roof pitch. Retrofit flashing is available for piping with welded caps or cross bars. Colors available in standard square and round base pipe flashing. Round Base Size Pipe size Base Size 1 1/4 2-1/2" 4-3/4" Closed Top 2 1-3/4 3" 6-1/4" 3 1/4 5" 7-3/4" Closed Top /4" 9-1/4" 5 4-1/4 7-3/4" 10-3/4" 6 5 9" 12-1/4" " 14-1/4" " 16-1/2" " 25-1/2" Retrofit Square Base Size Pipe size Base Size 1 1/2 4" 8-3/16" /4" 14-1/4" 3 9-1/4 16-1/4" 21-1/2" Retrofit Round Base Zipper Size Pipe size Base Size 1 3/4 2-3/4" 4-3/4" /4" 10-3/4" 3 3-1/4 10" 25-1/4"

68 Closure and Venting Products Pipe Flashing Square and round base pipe flashing For roof pipe flashing Multi-Flash Square Base Size Standard Pipe size Retrofit Pipe size 3 1/4 5-3/4" 2 4-1/2" /4" 3-1/2 6-3/4" 8 6-3/4 13-1/2" 6-1/2 12" MAXI /2" 13 27" Material Specifications Test Type EPDM Silicone (Hi-Temp) Advance ozone resistance 500 pphm 70 Hrs. 70 Hrs. High temperature: Intermittent +275º F +500º F Continuous +212º F +437º F Low temperature: Resistance tested to -65º F -100º F Tensile strength 1450 psi 700 psi Options Colors Available

69 Closure and Venting Products ProfileVent Metal roofing ridge vent in a roll ProfileVent Rolls New or re-roof on Purlin or wood deck Construction: Use a 2" opening at the ridge to provide ventilation. On new or re-roof wood deck construction, cut a 2" slot at the ridge (1" each side, start cut 6" from gable ends). On purlin construction position panels to leave a 2" opening. 40 year limited warranty Glue spots prevent slipping during installation Fits under any ridge cap Fits any pitch 2:12 20:12 One person roll-out installation Won t scratch panel finish Won t crack, dent or rust during shipping or installation Won t clog from airborne dust Prevents insect infiltration Prevents snow infiltration Provides proven roof ventilation Meets all model building codes Packing in English, French and Spanish No waste use leftovers on next job Will not support a flame Made in U.S.A. Available in convenient sizes 20' package 50' package 100' package Allow 2" opening at ridge for 1ventilation. ProfileVent is rolled out along the ridge, gable to gable, about 1" up-slope from the ridge cap edge. The positioning adhesive on most profiles will hold ProfileVent in position and allow for repositioning. ProfileVent can be cut with 2 scissors or utility knife. Inset: When splicing ProfileVent, make the splice at the center top of the high rib and use caulk or sealant along the splice. Screw down or pop rivet the ridge 3cap according to manufacturer s instructions (works with any ridge cap). Current panel profiles 3/4" Hi-Rib R-Panel ProfileVent matches most major OEM profiles. Call for Details.

70 Closure and Venting Products ProfileVent Metal roofing ridge vent in a stick For 3/4" Hi-Rib roofs 1" deep x 2" wide x 3' length Installs just like closure No release paper New improved adhesive Cut to fit profile Won t dry out from exposure 24 pieces/carton 72 linear feet ProfileVent 3' Stick New or re-roof on Purlin or wood deck Construction: Use a 2" opening at the ridge to provide ventilation. On new or re-roof wood deck construction, cut a 2" slot at the ridge (1" each side, start cut 6" from gable ends). On purlin construction position panels to leave a 2" opening. Allow 2" opening at ridge for 1ventilation. ProfileVent is positioned along the ridge, gable to gable, about 1" up-slope from the ridge cap edge. The positioning adhesive on most profiles will hold ProfileVent in position and allow for repositioning. 2 ProfileVent can be cut with scissors or utility knife. Inset: When splicing ProfileVent, make the splice at the center top of the high rib and use caulk or sealant along the splice. Screw down or pop rivet the ridge 3cap according to manufacturer s instructions (works with any ridge cap). Current panel profiles 3/4" Hi Rib

71 Closure and Venting Products Ventco Ridge Cap Anchor Clip Ridge cap anchor clip Anchor clips are recommended in high wind areas and on panels with major ribs 16" on center or greater. M9002 3/4" Anchor Clip M9004 1" Anchor Clip M /4" Anchor Clip M /2" Anchor Clip M /4" Anchor Clip M /2" Anchor Clip Ventco Ridge Cap Anchor Clip An independent engineering corporation tested the performance of the Ventco Ridge Cap Anchor Clip under high wind loading. During testing, a roof/ridge vent/cap system was subjected to wind speeds that follow the Dade County Test protocol. The following observations were made concerning the performance and structural integrity of the clip and ridge cap: No lifting of the ridge cap up to 115 mph No fastener pull out or loosening The ridge cap remained in contact with ventilation system No difference in performance when the cap is secured to the clip with screws or rivets Specifications 20 gauge galvanized steel Visible surface painted black for aesthetic purposes Install your metal roofing panel 1according to manufacturer s instructions. Apply mastic above and below pre-drilled holes in the clip. Before installing ProfileVent, insert #14A screw through the large downslope access hole in top of the Ridge Cap Anchor Clip. Lift the back end of clip. Slip 2ProfileVent under the clip. Push clip back down and insert another #14A screw in the up-slope hole. Packaging 25 clips per small box 24 small boxes per master box 600 clips per master box Anchor Clip Detail Options None Anchor Clip U.S. Pat (other patents pending)

72 Closure and Venting Products Butyl Tape Sealant Tape Designed for side and end lap sealing of metal panels, roof vents and pipe flashing Exceeds sealing requirements for AC, refrigeration and windows Extruded on silicone coated paper for easy application Greater cohesive strength Superior adhesion Withstands extreme roof temperatures Superior low temperature compressibility Cold flow resistant Resistant to UV light Contains anti-oxidants, fungicides and anti-bacterial agents Seal not affected by normal movement of building Wide service temperature range Tested Physical Properties Test Method Test Typical Results Meets or exceeds all requirements of: Military Spec MIL-C 18969B Type II Class B Federal Spec TT-C 1796A Type II Class B N.A.A.M.M. SS-1C-68 A.A.M.A AND M.B.M.A. Ice Damming - Five-Inch static water head test F.D.A. Regulations (# ) GSTM 10* Color Light Grey ASTM D Cone 77 F/25 C, g/5sec. 1/10mm ASTM C Non-volatiles, % 212± F/100±-2 C ASTM D F 12.9 lbs 25 C 1.50 kg ASTM D Specific 77 F/25 C 1.55 GSTM 11* Service temperature - range -60 to +275 F -51 to +135 C GSTM 16* Sag (3 160 F/71 C) None ASTM C Cold temperature flexibility 1/2" (12.7 mm) No cracking or Mandel -60 F/-51 C loss of adhesion GSTM 9* Webbing and elongation: 77 F/25 C 32 F/0 C GSTM 1* Adhesive/cohesive failure 3%/97% 77 F/25 C ASTM D Tensile strength, 77 F/25 C 25 ASTM D Weatherability - 1,000 hours in Q.U.V. No discoloration weatherometer (Cycle of 8 hours cracking, crazing, or 150 F/65 C; then 4 hours of loss of adhesion 104 F/40 C) * GSTM test methods available upon request. Recommendation Surfaces: All surfaces to be sealed should be free of dust, dirt, oil and moisture before applying sealant. Temperature: Apply in dry conditions above 40 F (4 C); At temperatures below 40 F (4 C) atmospheric condensation surfaces inhibit adhesion and should be avoided. : Apply MB-10A tape to surface directly from roll. Press sealant through the silicone release paper with a smooth, even hand motion. Note: for metal roofing and siding applications, place sealant under the fastener to prevent wind blown rain from leaking through the fastener holes. SFS Part # Size Feet Per Roll Rolls/Carton V8000 3/16" Bead Butyl Sealant 25' Roll 48 V8020 3/8" x 3/32" Butyl Sealant 45' Roll 48 V8040 1/2" x 3/32" Butyl Sealant 50' Roll 20 V8080 3/4" x 3/32" Butyl Sealant 50' Roll 14 Rolls are packed in water-resistant cartons.

73 Closure and Venting Products Hannoband BG1 Joint Sealant Tape Hannoband BG1 is a pre-compressed, self-expanding polyurethane foam with acrylate dispersion impregnation Provides resistance to rain, wind, sound, draft and dust Use for sealing joints and seams in metal panels, gaps around door and window frames, and expansion joints in buildings Pressure sensitive adhesive for fast and easy installation Flame retardant Technical Data BG1 provides maximum environment protection by: Greatly reducing air infiltration Highest levels of resistance to wind driven rain Superior sound proofing Extended functional life Highest fire rating Smallest thermal change (temperature gradient) inside and outside of sealed joint Property BG1 Color black Air Tightness ASTM E 283 2,4 l/sm (360 Pa) (1,59 cfm/ft (7,5 psf)) 0,55 l/sm (75 Pa) (0,3 cfm/ft (1,57 psf)) Resistance to water penetration ASTM E 331/E Pa ( 12,5 psf) Heat resistance -30 C - 90 C (-40 F F) Short Term: -40 C C (-40 F F) Tensile strength ASTM D3574/ISO 1798 > 100 kpa / > 14 psi Elongation ASTM D3574/ISO 1798 > 200% Compression force ASTM D3574/ISO ,4 kpa / 0,49 psi, 40% compression Density ISO kg/m³ ± 10% (4 lb/ft³) Thermal Conductance DIN EN λ = 0,0429 W/mk Shelf Life 18 months from date of production Compressed Expanded Joint Joint Width Roll Part # Dimension Dimension Depth Max. Min. Length Packaging /4" x 1" 1" x 1" 1" 1/8" 1/4" 26.2 ft. 12 rolls/ctn /8" x 1" 1-1/2" x 1" 1" 1/4" 3/8" 18.4 ft. 12 rolls/ctn Disposal Residue tape can be disposed of in the household waste. The local regulations are to be adhered to. Safety On the basis of existing data and experience, the product is not hazardous in the meaning of the Hazardous Material Regulations. We recommend however that you take the same care and use the same hygiene as with chemical materials. Cleaning Skin cleansing with soap and water. The impregnate and/or adhesive residues is possible with a petroleum-based cleaning agent. Please observe the safety regulations.

74 Closure and Venting Products Novaflex Metal Roof Sealant Novaflex metal roof sealant provides unbeatable adhesion to most common construction materials, including Kynar Non-corrosive, single component, oxime cured silicone sealant and/or adhesive s include metal roofs and siding, wood, galvanized steel, flashing, aluminum, PVC, windows and masonry Tack free in 10 minutes; completely cured in 2 days Permanently flexible; will not shrink, crack, sag or slump Provides a waterproof, weather tight seal Extrudes down to 0 F Will not freeze Product Specifications Physical Property Test Method Performance Range Appearance Colored paste Extrusion Rate 1/8" 50 psi grams Skin Over Time 50%RH & 77 F 5-10 minutes Through Cure 50%RH & 77 F 24 hours Technical Properties* Physical Property Test Method Typical Value Specific Gravity Tensile Strength ASTM D psi Elongation ASTM D % Tear Resistance ASTM D pli Shore Hardness ASTM D ± 8 Service Temperature -40 C C (-40 F F) Type S Join Sealant Designation ASTM C920 Grade NS Class 25 Use NT, M, G, A, O Adhesion Glass pli Aluminum ASTM D pli Vinyl pli * The values outlined reflect testing that was conducted on laboratory prepared specimens, actual results may vary. The information provided in the above table is not intended for use in preparing specifications. Please consult manufacturer for additional information. Continued on following page

75 Closure and Venting Products Novaflex Metal Roof Sealant Novaflex Novaflex Part # Sealant Color Part # Sealant Color White Sandstone Almond Red Dark Bronze Brown Black Green Sierra Tan Antique White Medium Bronze Translucent Light Gray Charcoal Gray Hemlock Green Gutter Gray Packaging Tube size and dimension: 10.3 fl. oz. (304 ml); 9" x 2" x 2" Case size: 12 tubes per case; weight - 20 lbs. Sold in case quantity only Installation Cures times of materials listed on this sheet are dependent upon environmental conditions such as temperature, humidity and application thickness Adhesion should be checked on small samples prior to full-scale application Can be used on interior and exterior Removable tips - no wasted sealant left in fixed tips No waste; ability to use entire tube, or can save with end cap Not paintable Safety Advantages and Precautions Low odor Solvent free VOC Compliant in all 50 states Not recommended for surfaces that are to be painted Not recommended for joints submerged under water Do not install if surface temperature is below 0 F or exceeds 120 F Obey all local, state and federal regulations for proper disposal of solvent and silicone waste Storage Shelf life of 18 months from date of manufacture when stored in the original, unopened container at 75 F or less

76 Tools and Accessories (RH2) Installation Product Screw Name: Guns #14 Installation (RH3) screw Description: guns and #3 drive Phillips sockets Drive (RH4) : Insulation board Installation to roof cover. tools Screw guns and noise pieces are matched for individual products to insure consistent installation performance. DI 600 Power Screwdriver For installing self-drilling fasteners Feature: Versa clutch system Screw gun manufactures and individual tools are tested and pre-qualified for reliable field performance before recommendation. Volts: 110 Amps: 6.5 Speed: rpm variable speed CF 50 Setting Nose Piece Installation tool with depth locator for long SX composite panel fasteners Features: ZA 1/4"/80 drive shaft E 380 drive socket irius Drive Socket The E-420 setting tool is required for installing the irius drive system The fasteners are clamped firmly via the teeth under the fastener head Socket E-420 E-420 parts kit Spare jaws Hex and Torx Drive Bits irius Drive Bit (E420) J0865 1/4" x 2-9/16" x 1/4" Lobular Hex Drive Mag Socket J0984 1/4" x 1" x 1/4" Lobular Hex Drive Mag Socket J0875 5/16" x 2-9/16" x 1/4" Lobular Hex Drive Mag Socket J0925 3/8" x 2-9/16" x 1/4" Lobular Hex Drive Mag Socket J0945 No. 3 Sq. Recess Drive Bit J0955 2/2 Quadrex x 3" x 1/4" Hex Drive J6900 1/4 Hex Magnetic Bit Holder T20W TORX Drive Bit J6800 T25 TORX Drive Bit 1" J2020 T25 TORX Drive Bit 1-5/16" SFS T-25 TORX Special For Evergrip T30 TORX Drive Bit