BRIDGE & SUPPLY COMPANY. Installation Guide. Ultra Includes:
|
|
- Ashley Harrison
- 7 years ago
- Views:
Transcription
1 BRIDGE & SUPPLY COMPANY Installation Guide Ultra 2000 Includes: Ultra 2000 Installation Guide Stock Trim Profiles Ultra 2000 Trim Installation Guide
2 Page 2 Table of Contents Ultra 2000 Profile, Colors Available, Additional Accessories... 3 Ultra 2000 Panel Installation Guide... 4, 5 Ultra 2000 Trim Installation Guide: One Piece Soffit... 6 Fascia Eave Trim... 6 Gable Trim... 6 Sidewall Flashing...7 Ridge Cap - 1 and 20 Wide... 7 W - Valley... 7 End Wall Flashing... 8 Outside Corner... 8 Inside Corner... 8 Overhead Door Trim... 8 Drip Cap... 9 Shingle Style Drip Edge... 9 Door Opening Trim... 9 Rat Guard... 9 Zee Trim J Channel & Box Base Trim F & J Trim... 10, 6, or 8 Fascia Square Track Cover Round Track Cover Round Double Track Cover... 11
3 Page 3 Ultra 2000 Custom Length Steel Roofing and Siding Sheets 38 wide providing 36 coverage with ribs 9 on center, in lengths 1 ft. through 40 ft. Standard G-60 29GA Stock Colors Available Sandstone ² Beige Light Gray ² Red ¹ Brown Dark Gray Patriot Red Burnished Slate Light Blue Clay Black Ocean Blue Regal White ¹ ² Burgundy Silver White ¹ ² Evergreen ² Tan Also available in Acrylic Coated Galvanized or Galvalume and Liner Grade in Regal White or Bright White All of the above colors are available in 29GA G-60 Ultra 2000 ¹ Available in G 100 Galvanized Coating ² Available in 26GA Ultra 2000 Light Panels White & Clear Peaklite Ridge Cap White & Clear Gray Sealer Tape - 3/8 x 45 Lg. Roll Touchup Paint Cannon Ball Steel Walk Doors Steel Perforated Soffit Panels Nails with Washer Woodgrip Screws with Washer Self-Drill Screws with Washer Roof Boots Additional Accessories Available Topside Formed Filler Strips Bottomside Formed Filler Strips LP Vented Closures Polyaire Filler Strips Profile Vent Material Square Track and Accessories Cannonball Kwik-Frame Door Fraiming Round Track and Accessories Cupolas Custom Bent Trims
4 Page 4 Ultra 2000 Installation Guide Handling When unloading bundles of Ultra 2000 extreme care should be used. Forklifts can dent or puncture bottom of sheets. Bundles may also bend or stretch in the middle if they are too long for forklift unloading. The panel edges must be protected during unloading and handling to assure good fitting laps. Cutting Storage Installation Any cutting and trimming necessary should be done with a steel cutting blade, Carborundum blade, profile shear, or nibbler. Always cut panels with the exterior side down. Avoid any Roof: Begin laying the roofing panels on the end of the building away from the prevailing wind so the side lap seams shall face away from the prevailing winddriven rain. The first panel determines the alignment of all remaining panels on the roof, so extreme care should be taken to accurately square the first sheet. The over-lapping rib edge should be flush with the edge of the roof, and the panel should overhang the eave approximately three inches to provide for a drip edge. The side rib with the drain channel should face the direction in which the sheets are being laid down. When the panel is positioned, it should be fastened through the first rib, top and bottom. The panel should be attached completely before starting the next panel. A tip for assuring straight alignment for successive rows of panels is to stretch chalk lines between nails driven into the ridge and end of each edge rafter. These lines will serve as guidelines to align panels. sparks or hot particles to the panel finish which could cause pitting and red rust. Sheets can have sharp edges, always wear eye and hand protection. Store Ultra 2000 panels in a dry place. Fan panels out to let air circulate. Stack off the ground on an incline to allow for any moisture run off. Panels should never be stored outside for more than a short period of time and should never be covered with plastic which allows condensation to occur. Any moisture trapped between sheets can cause superficial staining or lifting of the finish, considerably reducing the life of the paint. Failure to comply with the above recommendations voids any warranties. If roof requires more than one horizontal row of panels, temporarily fasten at two points, not the ends, along main middle ribs of Panel #1 in lower corner. Next, install Panel #2 above and end lapping over Panel #1. Align both panels with chalk line. Install Panel #3 next to Panel #1, side lapping. Install Panel #4 above Panel #3 side lapping over Panel #2 and end lapping over Panel #3. Temporarily fasten all panels. Check alignment at ridge and eave. Permanently fasten when all panels are in line. Refer to Figure. Ultra 2000 requires at least a 3/12 pitch with an 8 end lap when using more than one panel in a row. Sidewalls: Do not run siding all the way to the ground. Panels should lap at least 3 over splash board but not come in permanent contact with soil. The first siding panel must be plumb to assure straight alignment of the entire row of panels. Temporarily a wooden 1 x 2 or a steel rat guard can be used for a guideline about 3 below the top of the baseboard.
5 Page 5 Lap Detail Fastening Nails: Roof 2 Galvanized ring shank nails with a neoprene gasket should be driven through the top of each major rib, as in Drawing #1, taking care not to overdrive. The washer should be compressed securely against the metal. Sidewalls nails should be driven through the flat next to each major rib as in Drawing #2. Screws: When using plated self-drilling wood screws with combination metal and neoprene washer, at least penetration should be attained. Fasten in flat along each major rib on both roofing and siding as in Drawing #2 making sure the washer is secure. Drawing #1 Screw Fastener Positions for Eaves, Ridge and End laps Drawing #2 Nail Fastener Positions Drawing #3 Screw Fastener Positions for Intermediate Supports CORRECT TOO LOOSE TOO TIGHT
6 Page One Piece Soffit Fascia/Eave Trim 5-½ Roof Truss 12 2 Fascia Board One Piece Soffit J Channel 2 Fascia Eave Trim Roof Purlin 3- Fascia Eave Trim Roof Truss 4-1/8 Top Plate 7/8 Post 3 Gable Trim (Same as Outside Corner), 12, 14, and 16 Gable Trim
7 Page 7 4 Sidewall Flashing 6 Sidewall Flashing Purlin 5 Ridge Cap, 1 Wide Ridge Cap 5 2 Fastener 2-½ 1/2 Purlin Outside Closure -or- Vent Material 5 Ridge Cap, 20 Wide Ridge Cap 3 7 1/2 Purlin Outside Closure -or- Vent Material 2 Fastener W Valley Trim W Valley 13 13
8 Page 8 6 End Wall Flashing 5-1/2 Girt End Wall Flashing Outside Closure 6 Purlin 7 Outside Corner, 12, 14, and 16 Outside Corner Post Girt 8 Inside Corner, 12, 14 and 16 Post Inside Corner Girt 9 Overhead Door Trim and 12 Door Header Post 7/8 Girt 2 7-1/8 Door Stop Walk through door Overhead Door Trim
9 Page 9 10 Drip Cap Length: 10 Drip Edge 2-3/8 7/8 Door Stop Walk through door 11 Shingle Style Drip Edge Purlin 3 Truss Shingle Style Drip Edge 1/2 12 Door Opening Trim Post 6 Door Opening Trim Steel Siding 13 Rat Guard Length: /8 7/8 Base Board Rat Guard
10 Page Zee Trim Length: 10 or Fiberglass Panel 1-5/8 7/8 Girt Zee Trim or Fiberglass Panel 15 J Channel Length: 10 Door or Window Jamb 2-1/8 7/8 J-Channel 16 1 & Box Base Trim Foam Insulation Metal Siding Base Trim 17 F & J Trim Fascia/Eave Trim 1/2 6 Fascia Roof Truss 1- Fascia Board Perforated Soffit F & J Trim
11 Page 11 18, 6, or 8 Fascia Fascia/Eave Trim 8 6, 6, or 8 Fascia Fascia Board Roof Truss 19 Square Track Cover Perforated Soffit F & J Trim Track Support National Track Cover 3-1/ 3-1/2 Track Board 2-1/2 1/2 2-1/ on Door 19 Round Track Cover Track Cover 1-5/8 1- Track Support 6-7/8 1-1/ Track Board on Door 19 Round Double Track Cover Track Support Track Cover 1-5/ /8 Track Board # Track Bracket 4-1/2 on Door
12 BRIDGE & SUPPLY COMPANY Main Office: Warehouse: 400 Stoney Creek Drive th Street, S.E. P.O. Box 151 Sandusky, MI Grand Rapids, MI Ohio Plant: 9610 County Rd Fourteen Wauseon, OH Phone: Phone: Fax: Fax: Phone: (419) Fax: (419)
Residential Roofing Guide
Residential Roofing Guide TABLE OF CONTENTS Building Detail and Accessories...... 1 Panel Introduction and Handling...... 2 Cutting and Trimming.... 3 Roof Preparation..... 3 Roof Slope..... 3 Re-roofing...
More informationINSTALLATION MANUAL For Grand Rib-3 / Multi Purpose / & Classic Rib Roofing Panels
INSTALLATION MANUAL For Grand Rib-3 / Multi Purpose / & Classic Rib Roofing Panels Grand Rib-3 / Multi-Purpose / Classic Rib Grand Rib-3 / Multi-Purpose / & Classic Rib Grand Rib 3 panels are a strong,
More informationInstallation Manual for STANDING SEAM ROOFING
Installation Manual for STANDING SEAM ROOFING Absolute Steel Toll Free 877-833-3237 / Phone 480-768-1618 / Fax 480-768-1514 www.metalroofingsource.com Standing Seam features approximately one-inch high
More informationDiscount Direct Metal Roofing Plus Rib Roofing Panels Installation Instructions
Discount Direct Metal Roofing Plus Rib Roofing Panels Installation Instructions All questions and concerns please call 904-696-9700 Discount Direct Metal Roofing Plus Rib metal roofing panels are a strong,
More informationPOST FRAME LIGHT GAUGE APPLICATION GUIDE
POST RAME LIGHT GAUGE APPLICATION GUIDE Lebanon, PA 888.339.0059 Bridgton, ME 888.339.0059 Howe, IN 866.562.3782 www.everlastroofing.com Post rame Light Gauge Guage Post rame Trim Table of Contents Light
More informationGeneral Instructions and Guidelines
General Instructions and Guidelines Building Design and Construction To ensure adequate performance and longevity, protect metal panels from potentially corrosive situations and materials. When treated
More informationScrew Patterns Roof & Walls 403-279-2766 TR-36 MD-36 TSM-32. PBR-Panel
Screw Patterns Roof & Walls Overlap Underlap ¾ 9 TR-36 36 5/8 6 MD-36 36 ½ 8 TSM-32 32 1¼ 12 PBR-Panel 36 Bottom Edge Screw Pattern apply to every profile except for MD36 (1 screw beside every rib) High
More information4572 N Old US 31, Rochester, IN 46975 Toll Free: 877-889-7802 Fax: 574-223-7846 www.ramcosupply.com DETAIL MANUAL. and guide to Ramco Supply products
4572 N Old US 31, Rochester, IN 46975 DETAIL MANUAL and guide to Ramco Supply products Metal Roofing and Siding Panels & Accessories 1 4572 N Old US 31, Rochester, IN 46975 Ramco Supply s RAM Roofing Panels
More informationMETAL ROOFING INSTALLATION GUIDE
METAL ROOFING INSTALLATION GUIDE MIGHTY-RIB PBR (R-Panel) Regardless of whether your roofing project is a new installation or a re-roof, and whether your building is residential, commercial or agricultural,
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 27, 2013 the Easton - R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationDETAIL MANUAL. for Standing Seam. 2308 East 23rd Street Chattanooga, TN 37407. 1652 South Lee Hwy. Cleveland, TN 37311
DETAIL MANUAL for Standing Seam 1652 South Lee Hwy. Cleveland, TN 37311 2308 East 23rd Street Chattanooga, TN 37407 Best Buy Metals Standing Seam Roofing Panels Fig. 2 Standing Seam Panel Has 1 high nail-strip
More informationPreformed Metal Roofing and Siding
Page -1-1. GENERAL 1.1. Description This specification along with the drawings covers the furnishing of all material, products, equipment, accessories, tools, services, transportation, labor and supervision
More informationTable of Contents. Western States Standing Seam SS675 Panel Installation, Flashings & Shop Drawing Detail Guide. Notes to Designer /Installers..
Western States Standing Seam SS675 Panel Installation, Flashings & Shop Drawing Detail Guide Table of Contents Section Page Section Page Notes to Designer /Installers.. 1 Fastener Placement and Selection.2-3
More informationABSeam Panel Overview and Installation Instructions
82 Garden Spot Road Ephrata, PA 17522 717-445-6885 35 Ridge Road Newville, PA 17241 717-776-5951 ABSeam Panel Overview and Installation Instructions Applications: The ABSeam panel is an architectural panel
More informationProduct Catalog. Extreme Roofing, Inc. 2680 Rt. 982 Mammoth, PA 724.838.7695 www.extremeroofinginc.com
2012 Product Catalog Extreme Roofing, Inc. 2680 Rt. 982 Mammoth, PA 724.838.7695 www.extremeroofinginc.com 2 PH. 724.838.7695 Email. sales@extremeroofinginc.com Website. www.extremeroofinginc.com Fax.
More informationInstallation Guide MATTERHORN METAL ROOFING TO LAST A LIFETIME. MATTERHORN Standing Seam
Installation Guide MATTERHORN METAL ROOFING TO LAST A LIFETIME MATTERHORN Standing Seam System Components Placement G F J K I A. Standing Seam Panel B. Valley Cleat/Sidewall Counter Flashing D G B C A
More informationChapter 9: INSTALLING ROOFING
9.1 LEAK BARRIER (ICE AND WATER SHIELD) 9.2 SHINGLE UNDERLAYMENT 9.3 INSTALLING GUTTER APRON AND GABLE D-EDGE 9.4 INSTALLING SHINGLES 9.5 RIDGE VENT AND CAP Tools needed by each volunteer: Hammer (16 oz.
More informationPHILLIPSmfg.com 800.822.5055
PHILLIPSmfg.com 800.822.5055 About Us Phillips Manufacturing Company produces roofing metals, drywall framing components, stucco accessories and other finishing products. Established in 1955, we are a
More informationAsphalt Shingle Application Requirements
Alberta Allied Roofing Association Asphalt Shingle Application Requirements Section 1 Roof Decks 1.1 General Asphalt Shingles are not permitted to be installed directly over rigid insulation. When Asphalt
More informationSELF-STORAGE BUILDINGS
SELF-STORAGE BUILDINGS QUALITY and RELIABILITY The self-storage business has grown into a multi-billion dollar industry. Current businesses are expanding and new companies are starting up every day. The
More informationINSTALLATION OF A BAY WINDOW
INSTALLATION OF A BAY WINDOW Installation of a Bay Window These instructions relate to the replacement of an existing bay window or replacement of a straight window with a new bay window, in an opening
More informationUNIT 4: SHEATHING AND SHINGLING THE ROOF
KEY CONCEPTS 1. Identify tools needed for roofing 2. Steps to finishing a roof 3. Maintenance of a roof 4. Safety while roofing INSTRUCTIONAL ACTIVITIES 1. Complete Follow Up Worksheet from Unit 3 2. Roof
More informationPANELIZED HOME INSTALLATION GUIDELINE
PANELIZED HOME INSTALLATION GUIDELINE A typical home package will be constructed of Snap-N-Lock Insulated Panels clad with steel skins. 4" panels will be used for the walls, and 6" panels for the roof.
More informationCOMMERCIAL BUILDINGS. Quality Buildings Since 1983
COMMERCIAL BUILDINGS Quality Buildings Since 1983 Quality Buildings Since 1983 We are very proud of the buildings we construct Letter from the Owner: We appreciate your interest in a PDQ Building. I trust
More informationHfHMD uses LP SmartSide siding and trim.
HfHMD uses LP SmartSide siding and trim. These products are: More durable than cement fiber board. Much more volunteer-friendly to install. When installed correctly, have a 5/50- year pro-rated warranty.
More informationPOST AND FRAME STRUCTURES (Pole Barns)
POST AND FRAME STRUCTURES (Pole Barns) Post and frame structures. The following requirements serve as minimum standards for post and frame structures within all of the following structural limitations:
More informationSUPER SHED. Indoor shelter for your outdoor tools.
SUPER SHED Indoor shelter for your outdoor tools. Not everyone needs a garden shed. But, if you've no more space on your garage wall for that new leaf rake, if you can't find your potting trowel because
More informationPlans will call for one of two soffit/fascia details:
Plans will call for one of two soffit/fascia details: Ventilated vinyl soffit with bent aluminum fascia OR Ventilated LP Smartside soffit panels with 1x6 rabbeted fascia First, let s talk terminology:
More informationIF YOU NEED A POLE BARN OR DIY KIT CALL NOW AND LETS MAKE A DEAL
IF YOU NEED A POLE BARN OR DIY KIT CALL NOW AND LETS MAKE A DEAL Check out our Affordable Selection of DIY Pole Barn kit sizes and prices below. We offer a complete DIY pole barn kit plus independent experienced
More informationSECTION 07 61 13 STANDING SEAM METAL ROOFING
SECTION 07 61 13 STANDING SEAM METAL ROOFING PART 1 GENERAL 1.01 SCOPE OF WORK A. The Work shall include all labor, materials, equipment and supervision required to complete the work of the above referenced
More informationSAMPLE INSTRUCTIONS. Best Barns USA Assembly Book. the Denver. 12'x 12' or 12'x16' Revised November 29, 2010
Best Barns USA Assembly Book Revised November 29, 2010 SAMPLE INSTRUCTIONS the Denver 12'x 12' or 12'x16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775
More informationDrexel Metals Inc. DMC 100SS 16oz min. Copper Mechanical Seam Metal Roof System over Plywood
Drexel Metals Inc. DMC 100SS 16oz min. Copper Mechanical Seam Metal Roof System over Plywood Section 07411 Metal Roof Panels Part 1 General 1.1 Summary A. This section includes the following: a. Factory-formed
More informationShingle Installation Guide
Shingle Installation Guide Getting Started Dedicated to improving the environment, NewTech manufactures roofing tiles that are composed of up to 90% recycled post-industrial plastic. The manufacture of
More informationRetrofitting an Insulated Cold Roof
Retrofitting an Insulated Cold Roof As a metal-roofing contractor in the Upper Peninsula of Michigan, I am frequently asked to fix roof leaks that have less to do with roofing than with the way poorly
More informationVERTICAL LOCK Table of Contents
Table of Contents TABLE OF CONTENTS Vertical Lock Product Data Sheet... 2 Vertical Lock Engineering Data... 3 General Information... 6 Material Testing... 7 Panel Overview... 8 Handling Material & Storage
More informationStorage Store the siding in a dry and ventilated area. Do not place it directly on the ground. Always cover the siding after a day s work.
Installation Guide Before you begin, take the time to read this entire guide to clearly understand the requirements and steps to follow for proper installation. Warning Do not install defective material.
More informationSECTION 07720 PREFORMED METAL STANDING SEAM ROOFING
SECTION 07720 PREFORMED METAL STANDING SEAM ROOFING PART ONE GENERAL DESCRIPTION This section includes pre-formed standing seam metal roofing and related flashings, closures, trim and accessories including,
More informationSTEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE
STEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE 3 TO 30 METRE SPAN TILT UP METHOD SUPPLIED BY: Last update 8 December 2010 2010 FBHS (Aust) Pty Limited FBHS (Aust) Pty Limited ABN 83 126 232 504 trading
More informationMetal Building Systems Installation and Flashings & Details Guide. Table of Contents
Table of Contents Section Page Notes to Designer/User..................1-2 Map of Typical Roof Conditions............3 Fastener Placement.......................4 Fastener Selection........................5
More informationand Siding Effective Date 12/08 1
Application Manual for Metal Roofing and Siding Effective Date 2/08 Table of Contents General Information... 4 Required Tools... 4 Getting Started... 5 Important Notes... 6 Safety Precautions... 7 Panel
More informationTable of Contents. Western States RustWall Wall and Soffit Panels Installation, Flashings & Shop Drawing Detail Guide
Western States RustWall Wall and Soffit Panels Installation, Flashings & Shop Drawing Detail Guide Table of Contents Section Page Section Page Notes to Designer /Installers.. 1 Fastener Placement and Selection.2-3
More informationMinimizing Water Intrusion Through Roof Vents in High-Wind Regions
Minimizing Water Intrusion Through Roof Vents in High-Wind Regions http://www.fema.gov HURRICANE IKE RECOVERY ADVISORY Purpose: To recommend practices for minimizing water intrusion through roof vent systems
More informationSection Page Section Page
Western States Western Rib Panel Installation, Flashings & Shop Drawing Detail Guide Table of Contents Section Page Section Page Notes to Designer / Installers..1 Fastener Placement and Selection.2-3 Key
More informationSHINGLE APPLICATION GUIDE
SHINGLE APPLICATION GUIDE CONTENTS 01. General conditions 01. Material requirements 02. Terms 07. Estimating shingle requirements 08. Roof preparation 10.Shingle application E version 2006 GENERAL CONDITIONS
More informationClassic Products, Inc. ClickLock Standing Seam Installation Manual
Classic Products, Inc. ClickLock Standing Seam Installation Manual Classic Products, Inc. 8510 Industry Park Drive Piqua, OH 45356 800.543.8938 Table of Contents page Introduction 1. 1 Starter. 2. 1 Panels.
More informationMETAL ROOFING SYSTEM ORDERING & INSTALLATION SELF HELP GUIDE. Fabral, Inc 1
METAL ROOFING SYSTEM ORDERING & INSTALLATION SELF HELP GUIDE Due to product improvements, changes and other factors, Fabral reserves the right to change or delete information herein without prior notice
More informationPREMIUM LAMINATED ASPHALT SHINGLES Dallas, TX Tuscaloosa, AL Phillipsburg, KS
Application Instructions for THESE ARE THE MANUFACTURER S APPLICATION INSTRUCTIONS FOR THE ROOFING CONDITIONS DESCRIBED. TAMKO BUILDING PRODUCTS, INC. ASSUMES NO RESPONSIBILITY FOR LEAKS OR OTHER ROOFING
More informationHow to Install UnderDeck The Original.
How to Install UnderDeck The Original. TOOLS: Chalk Line Caulk Gun Garden hose or water bucket Gloves Hammer or Screw Gun Power Mitre Saw with OSB Blade Pencil Pliers Safety Glasses Straight Edge / Carpenter
More informationFree 12 x 8 Shed Plan With Illustrations, Blueprints & Step By Step Details
Free 12 x 8 Shed Plan With Illustrations, Blueprints & Step By Step Details Brought To You By: MyShedPlans Click Here To Download 12,000 Shed Plans >> 12 x 8 Basic Shed This 8 12-ft. shed features a simple
More information!!!!!! !!! Decra Plus DPSW010 DPSTW011 DPSW012 DPSW013 DPSW014 DPSW015 DPSW016 DPSW020 DPSW021 DPSW024 DPSW030 DPSW031 DPSW035 DPSW030 DPSW031 DPSW035
Decra Plus Drawing no DPSW010 DPSTW011 DPSW012 DPSW013 DPSW014 DPSW015 Description Shown In Decra Brochure Most Commonly Used Detail t~êã=oççñ=b~îéë=aéí~áä=b~îéë=lîéêü~åö=táíü=fåëìä~íéç=c~ëåá~=~åç=pçññáí
More informationINSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl windows with an integral nailing fin. While the use of these installation instructions
More informationSECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK
SECTION 07410 PREFORMED METAL STANDING SEAM ROOFING PART 1 - GENERAL 1.1 DESCRIPTION OF WORK A. This section covers the pre-finished, pre-fabricated Architectural standing seam roof system. All metal trim,
More informationCB-100 CB-150 CS-100 SL-100 SL-150 SLZ-1000
CB-100 CB-150 CS-100 SL-100 SL-150 SLZ-1000 Details and Installation Guide October 2013 All information, descriptions and dimensions in this manual are current at the time of printing. As always, Custom-Bilt
More informationThe Olympia Difference
The Olympia Difference Valued Customer, Thank you for choosing Olympia Steel Buildings as the solution to your building needs. You can be confident that the Olympia team of professionals will provide you
More informationGUIDE SPECIFICATION. Manufacturer: DECRA Roofing Systems, Inc.
GUIDE SPECIFICATION Manufacturer: DECRA Roofing Systems A Fletcher Building Company 1230 Railroad Street Corona, CA 92882 951-272-8180 phone 951-272-4476 facsimile www.decra.com SECTION 07313 [07 31 13]
More informationHome Depot Direct Special Order Retail Pricing 26 Gauge Horizon 16 & Ultra Loc 16 West Coast Standard
HORIZON 16 SKU # Retail UOM Model # Description WEST COAST MARKETS BYO5 Minimum Length 5ft for Horizon 16 and Ultra Loc 271814 $2.43 LnFt 4912200 26ga Horizon 16 Painted Galvalume Special Pricing for Copper
More informationStanding Seam Roof Systems
Standing Seam Roof Systems REAL PEOPLE. REAL PRODUCTS. REAL SOLUTIONS. www.a-s.com Building Benefits You Can Expect From A&S Materials Standing Seam roof panels weigh a relatively modest 11/2 pounds per
More informationSun Windows General Information Sun New Construction Window Installation Instructions
Sun Windows General Information Section 1 G F H H H A. Apply Weather Resistive Barrier B. Apply Sill Flashing Tape C. Place Waterproof Sill Shims D. Caulk Back of Nail Fin Sides & Top, Set Window, Fasten
More informationGreenGuard Housewrap Installation Guide
000768PACBPHW_Flashing Bro 5/23/03 2:52 PM Page 1 For the most current product information, go to www.green-guard.com. Pactiv Building Products believes the information and recommendations herein to be
More informationapplication instructions
application instructions ARCHITECTURAL COLLECTION PRIMED BOLD PROFILE 120 SERIES LAP SIDING (D5, T4, D8, T5, Q4) General At the time of manufacture, siding meets or exceeds the performance standards set
More informationCONTENTS. General conditions 2. Material requirements 3. Terms 4. Estimating shingle requirements 4. Roof preparation 6. Shingle application 9 - 1 -
CONTENTS General conditions Material requirements 3 Terms 4 Estimating shingle requirements 4 Roof preparation 6 Shingle application 9 Shingle Shingle application application guide guide - - b a 3a 3b
More informationPANEL CONCEPTS LLLP.
The Small Cottage Company DO-IT-YOURSELF CABINS & COTTAGES PANEL CONCEPTS INC. PANEL CONCEPTS LLLP. 2826 Gold 331 Creek N. M-33, Road Mio, Gold Michigan Creek, Montana 4864759733 (989) 826-6511 (406) 288-8585
More informationCITY OF WHITE BEAR LAKE BUILDING INSPECTION DEPARTMENT 4701 Highway 61 White Bear Lake, MN 55110 Fax: 651-429-8503. Re-Roofing: Asphalt Shingles
CITY OF WHITE BEAR LAKE BUILDING INSPECTION DEPARTMENT 4701 Highway 61 White Bear Lake, MN 55110 Fax: 651-429-8503 Re-Roofing: Asphalt Shingles This is a summary of the standard requirements based on the
More informationTitan Old World Spanish Tile
Installation Guide Titan Old World Spanish Tile Titan Manufacturing Phone: 407-587-5492 Fax: (866) 859-8607 www.titanroofsystems.com Rev 70908 This document includes the recommended and suggested installation
More informationRESIDENTIAL ROOFING & RE-ROOFING, ROOF VENTILATION AND ROOF SHEATHING REQUIREMENTS MICHIGAN RESIDENTIAL CODE 2000
RESIDENTIAL ROOFING & RE-ROOFING, ROOF VENTILATION AND ROOF SHEATHING REQUIREMENTS MICHIGAN RESIDENTIAL CODE 2000 SECTION R905 REQUIREMENTS FOR ROOF COVERINGS R905.1 Roof covering application. Roof coverings
More informationFinal inspections are completed by site visit only. Access to fenced yards shall be planned.
ROOFING RESIDENTIAL BUILDING INSPECTIONS DEPARTMENT www.ci.blaine.mn.us This handout is intended only as a guide and is based in part on the 2015 Minnesota State Building Code, Blaine City ordinances,
More informationSTANDARD PROCEDURES FOR INSTALLATION OF METAL ROOF SYSTEMS
ROOFING APPLICATION STANDARD (RAS) No. 133 STANDARD PROCEDURES FOR INSTALLATION OF METAL ROOF SYSTEMS 1. Scope 1.1 This application standard has been developed to provide consistent information for the
More informationFig. 2 WALL-TO-WALL PANEL CONNECTIONS CORNER WALL CONNECTION
SIPS SCREWS WITH MINIMUM 1" PENETRATION IN WOOD MEMBER IN SIP WALL PANEL CONNECTED TO @ 24" O.C. MAXIMUM OUTSIDE SKIN EACH SIDE OF FRAMING TYP. AS RECOMMENDED BY FOAM CORE AS EACH SIDE OF FRAMING TYP.
More informationPole Building Estimate Number: 4992 12/2/2010 NORTH SIDE-EAVE SIDE 2 ELEVATION
NORTH SIDE-EAVE SIDE 2 ELEVATION SOUTH SIDE-EAVE SIDE 1 ELEVATION WEST SIDE-GABLE SIDE 2 ELEVATION EAST SIDE-GABLE SIDE 1 ELEVATION Wheeling Centurydrain Steel Roofing Metal Drip Edge Facia Board Facia
More informationGENERAL RUBBER LINING PRINCIPLES
GENERAL RUBBER LINING PRINCIPLES I. METAL PREREQUISITES Metal to be lined should meet the requirements as stated in section 8 Metal Fabrication and section 12 Blasting and Cementing Procedures. The surface
More informationGUIDE SPECIFICATION. Manufacturer: DECRA Roofing Systems, Inc.
GUIDE SPECIFICATION Manufacturer: DECRA Roofing Systems A Fletcher Building Company 1230 Railroad Street Corona, CA 92882 951-272-8180 phone 951-272-4476 facsimile www.decra.com SECTION 07314 [07 31 14]
More informationWINDOW INSTALLATION GUIDE
WINDOW INSTALLATION GUIDE is not responsible for or liable for any use or misuse of the information contained in this window installation guide. Window Installation Guide This guide provides basic information
More informationROOF CONSTRUCTION Roof Styles Gable Roof Hip Roof Gambrel Roof
ROOF CONSTRUCTION The overall appearance of a building is greatly affected by the roof lines and the roofing materials. The designer has many standard designs to choose from and should be able to find
More informationBarewood Octagon and Elongated Windows Installation Instructions
Step-by-step instructions to a beautiful window. Measuring and Installation of your new window from Century Specialty Windows couldn't be easier with our step-by-step instructions. Quality, function and
More informationCedar Cottage Doghouse Plans
Overlapping cedar shingles add an element of charm to this medium size doghouse. The walls, floor, and trim are constructed of solid cedar, making it naturally weather resistant and provides excellent
More informationADDENDUM # 1 To: 1112-909-62-3698 RFP for: Various Construction Maintenance & Repair Services
818 S. FLORES ST. SAN ANTONIO, TEXAS 78204 www.saha.org Procurement Department ADDENDUM # 1 To: 1112-909-62-3698 RFP for: Various Construction Maintenance & Repair Services Remove and replace in their
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationPreparation / Roofing & Siding Application
Contents Page Preparation / Roofing & Siding Application... 2-3 Installation Tips... 4-5 Storage, Tools. 6 Safety Tips, Maintenance, Important Notice.. 7 Dormer Detail.. 8 Snow and Ice Management......
More informationROOFING APPLICATION STANDARD (RAS) No. 150 PRESCRIPTIVE BUR REQUIREMENTS
ROOFING APPLICATION STANDARD (RAS) No. 150 PRESCRIPTIVE BUR REQUIREMENTS 1. 2. 3. 3.0 Scope 1.1 This application standard shall be used where the authority having jurisdiction has adopted its use, and
More informationGeneral Specifications
- INSTALLATION GUIDE - Standing Loc Rib (SLR) High Custom Length Concealed Fastener 16 12 ¾ 1¼ 7 / 8 ¾ 1¼ ⅞ With Stiffener Ribs With Stiffener Ribs 16 12 ¾ 1¼ Flat Pan ¾ 1¼ Flat Pan 16 12 ¾ 1¼ With Striations
More informationVinyl Siding Estimating and Installation Guide
Vinyl Siding Estimating and Installation Guide Understanding the Basics Contractors and homeowners alike have depended on the low maintenance sidings from KP Building Products for the best product designs
More informationHURRICANE MITIGATION RETROFITS FOR EXISTING SITE-BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES
HURRICANE MITIGATION RETROFITS FOR EXISTING SITE-BUILT SINGLE FAMILY RESIDENTIAL STRUCTURES 101 Retrofits Required. Pursuant to Section 553.844 553.884, Florida Statutes, strengthening of existing site-built,
More informationCI SfB. (4-) Nn2. Onduline. Mini Profile. Onduline Garden Roof Range. Onduline Building Products Ltd
CI SfB (4-) Nn2 Onduline Mini Profile Onduline Garden Roof Range Onduline Building Products Ltd Onduline Garden Roof Range Onduline Mini Profile The new Onduline Mini Profile sheets have been designed
More informationLX STEEL BUILDING INSTALLATION MANUAL
LX STEEL BUILDING INSTALLATION MANUAL A complete guide to the installation of the Quicken Mfg. LX Building and its accessories Copyright 2015 Quicken Manufacturing Inc. 16454 SE Hwy 19 Cross City, FL 32628
More informationK2 STONE NATURAL VENEER
INTRODUCTION WHAT IS K2 NATURAL THINSTONE VENEER? Natural K2 Stone veneer is real stone, cut 1 inch thick, making it light enough to be installed as a veneer. Sometimes referred to as thin veneer, thin
More informationSuperform Products Ltd.
TYPICAL CORNER REINFORCING NOTE : SEE ENGINEERED REBAR SCHEDULES SUPPLIED BY THE MANUFACTURER STEEL REINFORCEMENT WALL CORNER 90 Copyright 2012 Sept. 2012 5.1.1 Rebar Spacing 6" 12" Max. Load LB./FT. 2000
More informationStormproof Your Roof. I ve done enough roof repairs to know that storm water that gets past the shingles
Stormproof Your Roof Self-adhering underlayment provides critical protection in vulnerable locations BY MIKE GUERTIN I ve done enough roof repairs to know that storm water that gets past the shingles and
More informationAdditions and Alterations
Additions and Alterations Addition and alteration construction is a miscellaneous grouping of home improvement and renovation projects that are generally geared toward the enhancement of an existing principal
More informationInstallation Manual. Solar Pool Heating System. Read the complete manual before beginning the installation
Solar Pool Heating System Installation Manual Read the complete manual before beginning the installation 1. Sizing the System Visit www.techno-solis.com to size the system using the sizing calculator.
More informationCLIENT. Inspection Report. 271 Front St. Alert Bay, B.C. Island Building Inspections V ANCOUVER I SLAND B. C.
CLIENT Inspection Report 271 Front St. Alert Bay, B.C. Island Building Inspections 2013 V ANCOUVER I SLAND B. C. Elevation Photos For the Property at 271 Front Street Alert Bay, BC ELEVATION PICTURES Front
More informationPRO-PANEL II. Panel Information. Detail Conditions. Flashing Profiles. Notes. Accessory Profiles. Testing Information
Table of ontents Product Page No. Product Page No. Panel Information Profile... PPP-2 Panel Overview... PPP-2 Flashing Profiles Eave (Direct Fasten)... PPP-3 leat... PPP-3 Box Gutter... PPP-3 Box Gutter
More informationThe Butler MR-24 Standing Seam Roof Difference. A comparison between metal roof systems
The Butler MR-24 Standing Seam Roof Difference A comparison between metal roof systems Roof Systems Necessities Weathertight (don t leak!) Low maintenance Weathertightness Roof clips, seams, panel alignment
More informationROOF CONSTRUCTION Roof Styles Gable Roof Hip Roof Gambrel Roof
ROOF CONSTRUCTION The overall appearance of a building is greatly affected by the roof lines and the roofing materials. The designer has many standard designs to choose from and should be able to find
More informationGerard Installation Manual Shingle Profiles
Gerard Installation Manual Shingle Profiles Granite Ridge Shingle Guardian Shingle March 2014 This Installation Manual is designed as an instructional tool to clearly depict to the contractor, installer,
More informationSteel Roofing and Siding Information & Installation Guide
Back to Service Steel Roofing and Siding Information & Installation Guide Locally Owned and Operated in Woodburn, Oregon Wholesale Manufacturer of Steel Roofing, Siding & Trim Introduction Valley Rolling
More informationfirst look at GigaCrete s revolutionary new New Construction GigaHouse GigaHouse Utilizing GigaPanel
first look at GigaCrete s revolutionary new New Construction GigaHouse GigaHouse Utilizing GigaPanel What is GigaCrete GigaCrete is a family of products based on low carbon footprint Green ceramic binders
More informationTHE USE OF STEEL BUILDING PANELS FOR ANIMAL CONFINEMENT
BACKGROUND Technical TSB 4.1 Bulletin Construction THE USE OF STEEL BUILDING PANELS FOR ANIMAL CONFINEMENT BACKGROUND TBP 2005.2 This Technical Bulletin is intended to assist users in the design and maintenance
More informationStandard Details for Metal Roofing & Siding
Standard Details for Metal Roofing & Siding Post Frame and Residential Structures Check out New Installation Videos at www.fabral.com Blue Book Reprint 5.11.indd 1 5/11/2011 9:09:22 AM Disclaimer The details
More informationWe urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit.
Important Information for New Construction Installations Attention Installer! We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden
More informationPrefab Instruction Manual
Prefab Instruction Manual http://www.muellerinc.com TABLE OF CONTENTS A. Site and Foundation Preparation 1. General Information 2. Squaring of Foundation 3. Anchor Bolt Settings (Pgs. 3,4) B. Building
More information