Air Fittings & Tubing

Transcription

1 For Pneumatic Piping Air Fittings & Tubing Air Fitting Series One-touch In/Out connection Possible to use in vacuum to 0kPa One-touch ini Series KJ Applicable tube etric size Applicable tube material Nylon Soft nylon Polyurethane 5 Unions Applicable tube ø.2 ø ø ø ø ø ø1 W/ sealant Electroless nickel plated Page General Purpose Fitting Series One-touch In/Out connection Possible to use in vacuum to 0kPa One-touch Fittings Series KQ2 Applicable tube etric size Low-torque rotation Rotary One-touch Fittings Series KS (Standard) Series KX (igh speed) Applicable tube etric size One-touch In/Out connection For compact and concentrated tubing applications One-touch Fittings anifold Series K Applicable tube etric size Possible to use in vacuum to 1.kPa Possible to use in vacuum1. -2 Insert Fittings Series KF Applicable tube etric size Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane 5 Unions 5 ø ø ø Unions Tubing connection/disconnection without use of tools iniature Fittings Series Nylon Soft nylon Polyurethane Applicable tube etric size Accepts soft copper tubing Self-align Fittings Series, DL, L, LL Applicable tube etric size Nylon Soft nylon Soft copper (C20T-0) Unions

2 Air Fittings & Tubing General Purpose Fitting Series Air Fitting Series One-touch In/Out connection With quick disconnect and air lock Self-seal Fittings Series KC Applicable tube etric size ulti tube, One-touch In/Out connection ulti-connector Series D Applicable tube etric size Rectangular ulti-connector Series KD Applicable tube etric size Centralized distribution of supply air Piping odule Series KB Applicable tube etric size Applicable tube material Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane 5 Unions tubes tubes tubes 20 tubes Applicable tube ø.2 ø ø ø ø ø ø1 W/ sealant Electroless nickel plated Page Inch-size One-touch Fittings Air Fitting Series One-touch Inch-size tubing/unf, NPT thread connection Possible to use in vacuum to 0kPa One-touch ini Series KJ Applicable area U.S.A. etc. One-touch Inch-size tubing/unf, NPT thread connection Possible to use in vacuum to 0kPa One-touch Fittings Series KQ2 Applicable area U.S.A. etc. One-touch Inch-size tubing/5, R, Rc thread connection Possible to use in vacuum to 0kPa One-touch Fittings Series KQ2 Applicable area Australia, Japan, etc. Applicable tube material Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane UNF Unions UNF Unions 5 Unions Applicable tube (inch) ø ø 5 2 ø 1 ø ø 5 1 ø ø W/ sealant Electroless nickel plated Page K D S T 2.0-2

3 Air Fittings & Tubing Fitting Series For Special Environments Inch-size One-touch Fittings Air Fitting Series Low-torque rotation for fast swivel and oscillating applications Rotary One-touch Fittings Series KS (Standard) Applicable tube Inch size Applicable thread UNF, NPT One-touch In/Out connection For compact and concentrated tubing applications One-touch Fittings anifold Series K Applicable tube Inch size Applicable thread NPT One-touch In/Out connection ulti-tube connector Rectangular ulti-connector Series KD Applicable tube Inch size Air Fitting Series One-touch In/Out connection For use where weld spatter is generated Flame resistant material UL-9 V0 FR One-touch Fittings Series KR Applicable tube etric size One-touch In/Out connection For use where weld spatter is generated Flame resistant material UL-9 V0 FR One-touch Fittings anifold Series KR Applicable tube etric size One-touch In/Out connection For use in corrosive environments Stainless series One-touch Fittings Series KG Applicable tube etric size One-touch In/Out connection For use in corrosive environments Stainless steel (SUS1) iniature Fittings Series S Applicable tube etric size Applicable tube material Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane Applicable tube material FR Soft nylon FR Double layer FR Soft nylon FR Double layer Nylon Soft nylon Polyurethane Nylon Soft nylon Polyurethane UNF tubes 20 tubes Unions ø ø 5 Unions 5 Applicable tube (inch) ø ø 5 2 ø 1 ø ø 5 1 ø ø Applicable tube ø.2 ø ø ø ø ø ø1 W/ sealant W/ sealant Electroless nickel plated Electroless nickel plated Spatter proof Page Page

4 Air Fittings & Tubing Fitting Series For Special Environments Air Fitting Series To dissipate static electricity Antistatic One-touch Fittings Series KA Applicable tube material Soft nylon Polyurethane 5 Unions Applicable tube ø.2 ø ø ø ø ø With sealant Electroless nickel plated Spatter proof Page Tubing General tubing 1.5Pa max. at 20 C Nylon Tubing Series T Color Black White Red Blue Yellow Green etric sizes ø ø (ø 5 2 ) ø (ø 5 1 ) ø ø ø1 Inch sizes (inch) ø " 1 1 (ø.2) ø 1 " ø " ø " ø 2 " Page 2.-1 For Slightly general flexible tubing 1.5Pa{.kgf/cm2}max.at20 C 1.0Pa max. at 20 C Soft Nylon Tubing Series TS Black White Red Blue Yellow Green 2.-2 Tubing Flexible 0.Pa max. at 20 C Polyurethane Tubing Series TU Black White Red Blue Yellow Green Clear Orange 2.- Extremely flexible 0.Pa max. at 20 C Soft Polyurethane Tubing Series TUS Black White Red Blue Yellow Green Opaque Yellow brown 2.- K D For flexibility and moving applications Polyurethane Coil Tubing Series TCU 1 tube 2 tubes tubes 2.-5 S T For flexible multi-tube applications Polyurethane Flat Tubing Series TFU 2 tubes tubes

5 Air Fittings & Tubing Tubing Use in spatter generating atmosphere/ Flame resistant material FR Soft Nylon Tubing Series TRS Flame resistance (Equivalent to UL-9 standard V-0) Color Black White Red Blue Green ø (ø 5 2 ) etric sizes ø ø (ø 5 1 ) ø ø ø1 Inch sizes (inch) ø (ø.2) ø 1 ø ø ø 2.- Page Accessories Tubing FR Double Layer Tubing Series TRB Flame resistance (Equivalent to UL-9 standard V-0) For preventing static electricity Antistatic Tubing Series TA Accessories / Tools ulti-tube older Series T ulti-holder Series TA Cutter Series TK Black White Red Blue Yellow Green Black Releasing Tool Series TG -5 Operation Guide For Air Fittings and Tubing With Sealant and Nickel Plated Option ow to Order S With sealant Without sealant S Sealant Note) With gasket for all of, 5 and threads X2 Option indication X2 With electroless nickel plated Fittings with Sealant The sealant (fluoro resin) is applied to the threaded portion with the correct thickness and range. This eliminates the work of wrapping and coating sealant, which simplifies piping. With sealant

6 Air Fittings & Tubing/Precautionsq Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to the main text for more detailed precautions of every series. Caution Caution Warning Selection qkeep the connection part of fitting and tubing from rotating to prevent cracking. Use Rotary One-touch Fittings Series KS (Standard) or KX (igh speed) for these cases. wthe tube bending radius in the vicinity of the fitting should be at least the minimum bending radius of the tube. If bent more than the min. bending radius, tubing may fail or be crushed. edo not use tubing for combustibles, explosives or poisoneous fluids like gas, fuel gas, coolant etc. They can permeate through tubing walls. rapplicable for general industry water. Consult SC if using other fluids. Surge pressure must be under the max. operating pressure. If surge pressure exceeds the max. operating pressure, fitting or tubing may be damaged. Installation qcheck whether tubing is not damaged before installing. Confirm model size, etc. wtake the change in tubing length due to applied pressure into consideration when piping. edo not apply unnecessary forces such as twisting, pulling, moment loads, etc. on fittings or tubing. This will cause damage to fittings and will crush, burst or release tubing. ravoid wear-out of tubing, twisted piping or damage to tubing to prevent crushing, bursting or release of tubing. twhen screwing together pipes and fittings etc., be certain that cutting dust from the pipe threads and sealing material do not get inside the piping. Furthermore, when pipe tape is used, leave 1.5 to 2 thread ridges exposed at the end. Environment qanti-static fittings (Series KA) and anti-static tubing (Series TA) are recommended for use where static electricity is a problem. Using other fittings or tubing may cause damage to the system and products. wflame resistant fittings (Series KR/KR) and tubing (Series TRS/TRB) are recommended for use in spatter applications. Fire may occur because of spattering. edo not use fittings and tubing where they are directly in contact with cutting oil, lubrication or coolant. Consult SC if using under such applications. aintenance Caution qreplace fittings or tubing having the following problems. a) Cracks, gouges, wearing, corrosion b) Air leakage c) Twists or crushing of tubing d) ardening, deterioration, softening of tubing wdo not reuse damaged fittings/tubing. Use of One-touch Fittings Caution q insertion and removal from One-touch fittings 1) Installing tube qcut the tube perpendicularly, being careful not to damage the outside surface. Use SC tube cutter TK-1, TK-2 or TK-. Do not cut the tube with pliers, nippers, scissors, etc., otherwise, the tube will be deformed and troubles may result. wgrasp the tube, slowly push it into the One-touch fittings until it comes to a stop. epull the tubing back gently to make sure it has a positive seal. Insufficient installation may cause air leakage or tube releasing. 2) Removing tube qpush in evenly on the release button. wpull out the tube while keeping the release button depressed. If the release button is not held down, the tube cannot be withdrawn. eto reuse the tubing, cut off the previously lodged portion of the tube. wto install the fittings, screw the fitting into the hexagonal face of the body, applying the appropriate wrench as close to the thread as possible. Use the spanner corresponding to the size of hexagonal portion, or hexagonal portion may be deformed. etightening the thread portion of an, 5 or fittings 1) First, tighten it by hand, then give it an additional 1/ turn with a wrench. 2) 5/ First, tighten it by hand, then give it an additional 1/ turn with a wrench. Excessive tightening may damage the thread portion or deform the gasket and cause air leakage. 2.0-

7 Air Fittings & Tubing/Precautionsw Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to the main text for more detailed precautions of every series. Caution Fittings with Sealant qthe standard thread torques of the fittings are as shown in the table below. In short, tighten by hand, then turn it two or three revolutions with a wrench. size NPT 1 1, NPT, R(PT) NPT, R(PT) NPT, R(PT) NPT, R(PT) Standard torque (Nm) to 9 to 1 to 2 2 to 0 wif the fitting is threaded in with excessive torque, a large amount of sealant will seep out. Remove the excess sealant. einsufficient tightening may loosen threads, or cause air leakage. rreuse 1) In most cases, two or three uses are possible. 2) Remove loose sealant stuck to the fitting by blowing air over the threaded portion of the fitting to prevent air leakage caused by entering sealant. ) If the sealant no longer provides an effective seal, wrap sealing tape over sealant before reuse. (Sealant in any form other than tape will not work.) tonce the fitting has been tightened, backing it out to its original position often causes the sealant to become defective. Air leakage will occur. Use of Tubing Other than SC s Brand Caution qwhen using a brand of tubing other than SC, be careful of the tolerance of the tube s 1) Nylon tubing ±0.1mm 2) Soft nylon tubing ±0.1mm ) Polyurethane tubing +0.mm, 0.2mm When the tolerance of the tube s is out of range mentioned above, do not use the tubing. Tubing can not be connected and it causes air leakage or tubing may come out. K D S T 2.0-

8 One-touch Fittings Applicable etric Size Series KQ2 ow to Order Connection, R(PT), Rc(PT) Symbol 2 Body White Black Color Release button Light gray Blue Accessory Name Nipple KQ2N Different dia. nipple Adapter KQ2C cap KQ2C Color cap KQ2P Plug (White) KQP Plug (Blue) KQ 2 0 One-touch Fitting 01 S Applicable tube 2 ø.2 0 ø 0 ø 0 ø ø ø 1 ø1 (Rod) odel ale connector Straight union T Different dia. straight S exagon socket head male connector TW F Female connector TX ale elbow TY Union elbow Y L Plug-in elbow D Reducer elbow ale branch connector LU Branch union elbow U K 5 male elbow V Universal male elbow VS ex. socket head universal male elbow UD VF Universal female elbow LF Female elbow XD VD Double universal male elbow X VT Triple universal male elbow R Z Branch universal male elbow E ZF Branch universal female elbow ZD Double branch universal male elbow LE ZT Triple branch universal male elbow Extended plug-in elbow W Extended male elbow Applicable to KQ2 (white body) only. Note) KQT0-0, KQT0-0, KQT-0, and KQT- are available as made to order. Port size/applicable tube 5 5 X 0. X R(PT), Rc(PT) 02 R(PT), Rc(PT) 0 R(PT), Rc(PT) 0 R(PT), Rc(PT) 00 Same dia. tube 0 ø 0 ø 0 ø ø ø 1 ø1 99 Same dia. rod Different dia. tube (Reducer) ale branch tee Union tee Different dia. tee Cross Different dia. cross Different dia. cross ale run tee ale delta Delta union Branch Y Union Y Different dia. union Y Plug-in Y Delta branch Different dia. double union Y Double plug-in Y Different dia. plug-in Y Plug-in reducer Bulkhead union Bulkhead connector Bulkhead male elbow With sealant Without sealant S Sealant Note) Port size of with sealant style: Only R(PT) R(PT) R(PT) R(PT) 2.1-9

9 Series KQ2: White body Series KQ : Black body Guide Collet Chuck Accepts nylon, and urethane tubes. as large retaining force. Release button Series KQ2: Light gray Series KQ : Blue Small disconnecting force. When the fitting is removed from the tubing, the chuck and collet are released, thus preventing them from biting into the tube excessively. PAT. Packing Can be used for a wide range of pressures from a low vacuum up to a pressure of 1.0Pa The use of a special profile ensures sealing and reduces resistance when the tube is inserted., R(PT), Rc(PT) Body O ring Stud when piping in a confined space. The body and threaded portion can turn independently. One-touch IN/OUT connection. Possible to use in vacuum to 0KPa. Applications for metric size tube Applicable tube material Nylon, soft nylon, polyurethane Order ade P Applicable Tubing Color material O. D. Series Series KQ2 Series KQ Specifications Operating fluid Air, Water ax. operating pressure 1.0Pa Operating vacuum pressure 0kPa Proof pressure.0pa Ambient and fluid temperature 5 to 0 C (Water: 0 to 0 C) JIS B020 (Taper pipe thread) portion JIS B0209 Class 2 (etric coarse thread) Nut JIS B01 Class 2 (etric fine thread) Sealant ( portion) With sealant or none Note1) Applicable for general industry water. Consult SC if using for other fluids. Surge pressure must be under the max. operating pressure. Component aterials Body Stud Chuck Guide Collet, Release button Packing, O ring Gasket Body White Black Nylon, Soft nylon, Polyurethane ø.2, ø, ø, ø, ø, ø, ø1 Release button Light gray Blue C0BD, PBT, PP C0BD ( portion) Stainless steel (SUS0) SUS0, C0BD, Polyacetal (PO) Polyacetal (PO) NBR SUS0, NBR 2.1- K D S T

10 Series KQ2 odel ex. socket head male connector Universal male elbow KQ2S P KQ2V P Internal hex. allows thread connection by using an Allen wrench for confined spaces. Universal male elbow allows thread connection by using a socket wrench for confined spaces. 5 male elbow KQ2K P.2.1- Used in applications where a 5 elbow or male connector stresses the tubing. Extended male elbow KQ2W P.2.1- For when the elbow extends over a standard elbow for easier of connection/ disconnection of tubing. Bulkhead union Bulkhead connector KQ2E P Used for junction connection of two tubes for installation of a panel. KQ2E P Used for transit connection of a tube and a male screw for installation of a panel. Nipple KQ2N P Used for connection of two One-touch fittings. Reducer nipple KQ2N P Used for connection of two One-touch fittings that are different tube s. ale connector ale elbow ale branch tee Used to pipe in the KQ2 P KQ2L P Used to pipe in right same direction from KQ2T angle to female female threaded threaded portion. portion. ost ost common style. common style. Female connector KQ2F P P.2.1- Used to pipe from the male threaded portion such as pressure gauge. Union elbow KQ2L P.2.1- P P.2.1- Used to connect tubes at right angles. Union tee Straight union Plug-in elbow Different dia.tee KQ2 P KQ2L Used to change by KQ2T Used to connect tubes 90 in a tube fetching in the same direction. direction from Onetouch fittings. KQ2T P.2.1- P.2.1- P.2.1- Different dia. straight Reducer elbow Different dia. tee Used to change by KQ2 P KQ2L 90 in tube fetching KQ2T P.2.1- Used to connect direction from Onetouch fittings and to different size tubes. size down. P Cross Different dia.cross Different dia.cross KQ2TW KQ2TX Used to connect tubes KQ2TY Used for four branch with size down in all connections of tubes. 90 directions. P Used to branch line from female thread in both 90 directions. Used to connect tubes in both 90 directions. Used to connect tubes with size down in both 90 directions. Used to branch from in the same direction from thread and in 90 directions. Used to branch connection of tubes with size down in three directions

11 One-touch Fittings Series KQ2 ex. socket head universal male elbow Triple branch universal male elbow Union Y Used for six branches at KQ2VS P ex. on the top allows KQ2ZT P.2.1- right angles from the KQ2U P thread connection by female thread. using an Allen wrench Three individual parts for confined spaces. rotate 0. Used to connect tubes in the same direction. ale branch connector Branch union elbow Different dia.union Y KQ2LU P.2.1- Used for connection KQ2LU P KQ2U P Used for connection of at right angles from tubes at right angles. the female thread. Used to connect tubes with size down in the same direction. Universal female elbow KQ2VF P.2.1- Used for the same direction or at right angles from the male or female thread. ultiplex connections possible. Extended plug-in elbow KQ2W P When the elbow extends over a standard elbow for ease of connection/disconnection of tubing. Plug-in Y KQ2U P Used to branch tubing in the same direction from Onetouch fittings. Female elbow KQ2LF P.2.1- Used to pipe the tube at right angles from the male elbow. ale delta union KQ2D P Used for two branch piping at right angles from the female thread. Branch Y KQ2U P Used to branch line in the same direction from female thread. Double universal male elbow KQ2VD P.2.1- Used for branch piping at right angles from the female thread. Two individual parts rotate 0. Delta union KQ2D P Used for three branch connections of tubes at right angles. Plug-in reducer KQ2R P Used to change size of One-touch fittings. Triple universal male elbow KQ2VT P Used for branch piping at the right angles from the female thread. Three individual parts rotate 0. Delta branch KQ2UD P Used for four branch piping in the same direction from the female thread. Bulkhead male elbow KQ2LE P Used to connect two tubes through a panel changing by 90 in a tube fetching direction. Branch universal male elbow KQ2Z P exagonal head allows thread connection by using a box wrench. Used for branch connection. Different dia. double union Y KQ2UD P Used for four branch connections in the same direction reducing the size of the tubes. Adaptor KQ2N P Used to connect the fitting and R (PT) female thread. Branch universal female elbow KQ2ZF P Used for branch line in the same direction or at right angles from the male or female thread. ultiplex connection possible. Different dia. plug-in Y KQ2X P Used for branch connections from the fitting reducing the size of tubes. cap KQ2C P Used to plug the unused tube. K Double branch universal male elbow KQ2ZD P.2.1- Used for four branch connections at right angles from the female thread. Two individual parts rotate 0 Double plug-in Y KQ2XD P Used for four branch connections from the fitting reducing the size of tube. Color cap KQ2C P ounted on the release button corresponding to its applications. Distinguished by color. D S T ale run tee KQ2Y P Used for a branch line in the same direction from female thread and in 90 directions. Plug KQ2P, KQP P Used to shut unused One-touch fittings. KQP (Blue) KQ2P (White) 2.1-

12 Series KQ2 ale connector: KQ2 <5, > <R(PT)> R(PT).2 5 X 0. 5 X 0. KQ22-5 KQ22-01S KQ22-02S KQ20-5 X 1.0 KQ20- KQ20-01S 5 X 0. X 1.0 KQ20-02S KQ20-5 KQ20- KQ20-01S KQ20-02S KQ20-0S KQ20-01S KQ20-02S KQ20-0S KQ2-01S KQ2-02S KQ2-0S KQ2-0S KQ2-02S KQ2-0S KQ2-0S 1 KQ21-0S KQ21-0S SKQ1, #1 to #2 1 5 X 0. X X 0. X 1.0 KQ2S0-5 KQ2S0- KQ2S0-01S KQ2S0-5 KQ2S0- KQ2S0-01S KQ2S0-02S KQ2S0-01S KQ2S0-02S KQ2S0-0S KQ2S-01S KQ2S-02S KQ2S-0S KQ2S-0S KQ2S-02S KQ2S-0S KQ2S-0S KQ2S1-0S KQ2S1-0S (ex.) exagon socket head male connector: KQ2S <5, > <R(PT)> R(PT) Female connector: KQ2F 1 KQ2S0 to KQ2S KQ2S1 Rc(PT) KQ2F0 to KQ2F KQ2F1 KQ2F0-01 KQ2F0-02 KQ2F0-01 KQ2F0-02 KQ2F0-0 KQ2F0-01 KQ2F0-02 KQ2F0-0 KQ2F-02 KQ2F-0 KQ2F-02 KQ2F-0 KQ2F-0 KQ2F1-0 KQ2F1-0 (ex.) L A L A SKQ1, #25 to #1 SKQ, #1 to #2 (ex.) (2) area (mm 2 ) Nylon Urethane (9) Reference dimensions after R(PT) thread installation. Note1) : max. diameter Note2) ( ): Values for soft nylon L1 2 SKQ1, #2 to #5 SKQ, # to # (2) area (mm 2 ) Nylon Urethane (9) Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter Note2) ( ): Values for soft nylon L (2) area (mm 2 ) Nylon Urethane (9) Reference dimensions after R(PT) thread installation. Note1) 2: max. diameter Note2) ( ): Values for soft nylon <5, > <5, > <R(PT)> KQ2F0 to KQ2F1 <R(PT)> KQ2S0 to KQ2S1

13 One-touch Fittings Series KQ2 Straight union: KQ2.2 1 KQ22-00 KQ20-00 KQ20-00 KQ20-00 KQ2-00 KQ2-00 KQ21-00 KQ22 to KQ2 KQ L SKQ2, #1 to # SKQ, # area (mm 2 ) Nylon (2) Urethane (9) Note1) : max. diameter Note2) ( ): Values for soft nylon. Different diameter straight: KQ2 a b.2 1 KQ22-0 KQ20-0 KQ20-0 KQ20- KQ2- KQ2-1 KQ22 to KQ2 KQ L SKQ2, # to #11 SKQ, # area (mm 2 ) Nylon Urethane Note1) : max. diameter ale elbow: KQ2L <5> <> <R(PT)>.2 R(PT) 5 X 0. 5 X 0. X X 0. X SKQ2, # to #5 KQ2L2-5 KQ2L2-01S KQ2L2-02S KQ2L0-5 KQ2L0- KQ2L0-01S KQ2L0-02S KQ2L0-5 KQ2L0- KQ2L0-01S KQ2L0-02S KQ2L0-0S KQ2L0-01S KQ2L0-02S KQ2L0-0S KQ2L-01S KQ2L-02S KQ2L-0S KQ2L-0S KQ2L-02S KQ2L-0S KQ2L-0S KQ2L1-0S KQ2L1-0S (2) 1 2 L1 (ex.) area (mm 2 ) Nylon Urethane (1) () 5 Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter Note2) ( ): Values for soft nylon. <5, > <R(PT)> K D S T 2.1-1

14 Series KQ2 ale branch connector: KQ2LU <5, > <R(PT)> R(PT) 5 X 0. X X 0. X 1.0 SKQ, #1 to #1 KQ2LU0-5 KQ2LU0- KQ2LU0-01S KQ2LU0-02S KQ2LU0-5 KQ2LU0- KQ2LU0-01S KQ2LU0-02S KQ2LU0-0S KQ2LU0-01S KQ2LU0-02S KQ2LU0-0S KQ2LU-02S KQ2LU-0S KQ2LU-0S KQ2LU-02S KQ2LU-0S KQ2LU-0S (ex.) L L L A P area (mm 2 ) Nylon Urethane Reference dimensions after R(PT) thread installation. Note1) : max. diameter <5, > <R(PT)> 5 ale elbow: KQ2K <5, > <R(PT)> 1 R(PT) 5 X 0. X X 0. X 1.0 KQ2K0 to KQ2K KQ2K1 KQ2K0-5 KQ2K0- KQ2K0-01S KQ2K0-02S KQ2K0-5 KQ2K0- KQ2K0-01S KQ2K0-02S KQ2K0-0S KQ2K0-01S KQ2K0-02S KQ2K0-0S KQ2K-01S KQ2K-02S KQ2K-0S KQ2K-0S KQ2K-02S KQ2K-0S KQ2K-0S KQ2K1-0S KQ2K1-0S (ex.) L SKQ, #1 to # SKQ, # to # L A (2) area (mm 2 ) Nylon Urethane (5.) (.) Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter Note2) ( ): Values for soft nylon. <5, > <R(PT)> 2.1-

15 One-touch Fittings Series KQ2 Universal male elbow: KQ2V <5> <R(PT)> R(PT) 5 X 0. 5 X 0. 1 SKQ5, #1 to #1 KQ2V0-5 KQ2V0-01S KQ2V0-5 KQ2V0-01S KQ2V0-02S KQ2V0-01S KQ2V0-02S KQ2V0-0S KQ2V-02S KQ2V-0S KQ2V-0S KQ2V-0S KQ2V1-0S KQ2V1-0S (ex.) L1 L2 L A (55) (5) 1 Reference dimensions after R(PT) thread installation. (2) area (mm 2 ) Nylon Urethane Note1) 1: max. diameter Note2) ( ): Values for soft nylon. <5> <R(PT)> exagon socket head universal male elbow: KQ2VS <5> <R(PT)> R(PT) 5 5 SKQ5, # to #2 KQ2VS0-5 KQ2VS0-01S KQ2VS0-5 KQ2VS0-01S KQ2VS0-02S KQ2VS0-01S KQ2VS0-02S KQ2VS0-0S KQ2VS-02S KQ2VS-0S KQ2VS-0S KQ2VS-0S (ex.) L L L A area (mm 2 ) Nylon Urethane Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter <5> <R(PT)> K D S T 2.1-1

16 Series KQ2 Universal female elbow: KQ2VF <5> <R(PT)> Rc(PT) R(PT) 5 X 0. 5 X 0. SKQ, #1 to # KQ2VF0-5 KQ2VF0-01S KQ2VF0-5 KQ2VF0-01S KQ2VF0-02S KQ2VF0-01S KQ2VF0-02S KQ2VF0-0S KQ2VF-02S KQ2VF-0S KQ2VF-0S KQ2VF-0S (ex.) 1 2 L L L A Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter <5> <R(PT)> Female elbow: KQ2LF <5, > <Rc(PT)> RC(PT) 5 X 0. X X 0. X 1.0 SKQ #1 to #0 KQ2LF0-5 KQ2LF0- KQ2LF0-01 KQ2LF0-02 KQ2LF0-5 KQ2LF0- KQ2LF0-01 KQ2LF0-02 KQ2LF0-0 KQ2LF0-01 KQ2LF0-02 KQ2LF0-0 KQ2LF-02 KQ2LF-0 KQ2LF-0 KQ2LF-02 KQ2LF-0 KQ2LF-0 (ex.) L L area (mm 2 ) Nylon Urethane Note1) 1: max. diameter <5, > <Rc(PT)> Double universal male elbow: KQ2VD 2.1- R(PT) 1 2 (ex.) KQ2VD0-01S 1 KQ2VD0-02S. 1. KQ2VD0-0S KQ2VD0-01S 1 KQ2VD0-02S. 1. KQ2VD0-0S KQ2VD0-01S KQ2VD0-02S KQ2VD0-0S.2. KQ2VD0-0S KQ2VD-02S KQ2VD-0S KQ2VD-0S KQ2VD-02S KQ2VD-0S KQ2VD-0S SKQ, #1 to #1 L1 L L A P Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter

17 One-touch Fittings Series KQ2 Triple universal male elbow: KQ2VT R(PT) (ex.) 1 2 KQ2VT0-01S 1 KQ2VT0-02S. 1. KQ2VT0-0S KQ2VT0-01S 1 KQ2VT0-02S. 1. KQ2VT0-0S KQ2VT0-01S KQ2VT0-02S KQ2VT0-0S.2. KQ2VT0-0S KQ2VT-02S KQ2VT-0S KQ2VT-0S KQ2VT-02S KQ2VT-0S KQ2VT-0S SKQ, #1 to #1 L1 L L A P Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter Branch universal male elbow: KQ2Z <5> <R(PT)> R(PT) (ex.) 1 2 L1 L2 L P area (mm 2 ) A <5> Nylon Urethane 5 X 0. KQ2Z KQ2Z0-01S KQ2Z0-01S KQ2Z0-02S KQ2Z0-0S KQ2Z0-01S KQ2Z0-02S KQ2Z0-0S <R(PT)> KQ2Z-02S KQ2Z-0S KQ2Z-0S KQ2Z-0S 25 2 SKQ9, #1 to # Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter Branch universal female elbow: KQ2ZF <5> <R(PT)> R(PT) Rc(PT) (ex.) 1 2 L1 5 X 0. KQ2ZF KQ2ZF0-01S KQ2ZF0-01S KQ2ZF0-02S KQ2ZF0-01S KQ2ZF0-02S KQ2ZF-02S KQ2ZF-0S KQ2ZF-0S KQ2ZF-0S SKQ9, #1 to # L2 L A P Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter <5> <R(PT)> K D S T 2.1-1

18 Series KQ2 Double branch universal male elbow: KQ2ZD R(PT) (ex.) 1 2 L1 KQ2ZD0-01S 1 KQ2ZD0-02S. 1. KQ2ZD0-0S KQ2ZD0-01S 1 KQ2ZD0-02S. 1. KQ2ZD0-0S KQ2ZD0-01S KQ2ZD0-02S KQ2ZD0-0S.2. 2 KQ2ZD0-0S KQ2ZD-02S KQ2ZD-0S KQ2ZD-0S KQ2ZD-02S KQ2ZD-0S KQ2ZD-0S SKQ, #1 to #1 L L A P1 P Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter Triple branch universal male elbow: KQ2ZT R(PT) 1 2 L1 (ex.) KQ2ZT0-01S 1 KQ2ZT0-02S. 1. KQ2ZT0-0S KQ2ZT0-01S 1 KQ2ZT0-02S. 1. KQ2ZT0-0S KQ2ZT0-01S KQ2ZT0-02S KQ2ZT0-0S.2. 2 KQ2ZT0-0S KQ2ZT-02S KQ2ZT-0S KQ2ZT-0S KQ2ZT-02S KQ2ZT-0S KQ2ZT-0S SKQ11, #1 to #1 L L A P1 P Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter Union elbow: KQ2L.2 KQ2L2-00 KQ2L0-00 KQ2L L Q area (mm 2 ) Nylon Urethane KQ2L KQ2L KQ2L KQ2L () 29 SKQ, # to #2 Note1) : max. diameter Note2) ( ): Values for soft nylon. (2) 2.1-

19 One-touch Fittings Series KQ2 Branch union elbow: KQ2LU L1 L2 Q1 Nylon Urethane KQ2LU KQ2LU KQ2LU KQ2LU KQ2LU SKQ, #1 to #5 Note1) : max. diameter Q2 P area (mm 2 ) Plug-in elbow: KQ2L.2 Fitting size ød Fitting size ød 1 2 L1 L2 Nylon Urethane KQ2W2-99 KQ2W0-99 KQ2W KQ2W KQ2W A area (mm 2 ) KQ2W KQ2L2 to KQ2L SKQ, #1 to #25 Note1) : max. diameter KQ2L SKQ, # L1 L2 Nylon Urethane KQ2L2-99 KQ2L0-99 KQ2L KQ2L KQ2L KQ2L KQ2L () 2 KQ2L2 to KQ2L KQ2L1 Extended plug-in elbow: KQ2W SKQ, # to #11 SKQ, #9 A area (mm 2 ) (2) Note1) 1: max. diameter Note2) ( ): Values for soft nylon. Reducer elbow: KQ2L Fitting size ød 1 2 L1 L2 area (mm 2 ) Nylon Urethane.2 KQ2L KQ2L KQ2L KQ2L KQ2L KQ2L KQ2L KQ2L KQ2L SKQ, #1 to #25 Note1) 1: max. diameter A K D S T

20 Series KQ2 Extended male elbow: KQ2W <5> <R(PT)>.2 1 (2) 1 2 L1 L2 area (mm 2 ) A R(PT) (ex.) Nylon Urethane 5 X 0. KQ2W KQ2W2-01S KQ2W2-02S X 0. KQ2W KQ2W0-01S KQ2W0-02S X 0. KQ2W KQ2W0-01S KQ2W0-02S KQ2W0-0S KQ2W0-01S KQ2W0-02S KQ2W0-0S KQ2W-02S KQ2W-0S KQ2W-0S 5 KQ2W-02S KQ2W-0S KQ2W-0S.5 1 KQ2W1-0S (1) KQ2W1-0S () 5 KQ2W2 to KQ2W KQ2W1 SKQ1, #1 to # SKQ, #11 to # Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter Note2) ( ): Values for soft nylon. <5> <R(PT)> ale branch tee: KQ2T <5> <> <R(PT)> (2) 1 2 L1 L2 area (mm 2 ) A R(PT) (ex.) Nylon Urethane 5 X 0. KQ2T KQ2T2-01S 1 9. KQ2T2-02S X 0. KQ2T X 1.0 KQ2T0-1.. KQ2T0-01S KQ2T0-02S X 0. KQ2T X 1.0 KQ2T KQ2T0-01S KQ2T0-02S KQ2T0-0S KQ2T0-01S KQ2T0-02S KQ2T0-0S KQ2T-01S KQ2T-02S KQ2T-0S KQ2T-0S KQ2T-02S KQ2T-0S KQ2T-0S KQ2T1-0S.5 1 (1) KQ2T1-0S (0) 11 KQ2T2 to KQ2T SKQ1, #1 to #2 Reference dimensions after R(PT) thread installation. KQ2T1 SKQ, # Note1) 1: max. diameter Note2) ( ): Values for soft nylon. <5, > <R(PT)> 2.1-

21 One-touch Fittings Series KQ2 Union tee: KQ2T.2 KQ2T2-00 KQ2T0-00 KQ2T L Q area (mm 2 ) Nylon.. 1. Urethane KQ2T KQ2T KQ2T KQ2T () 0 SKQ, #1 to # Note1) : max. diameter Note2) ( ): Values for soft nylon. (2) 5 Different diameter tee: KQ2T a b 1 2 L1.2 KQ2T2-0 KQ2T0-0 KQ2T KQ2T KQ2T KQ2T (92.2) KQ2T2 to KQ2T KQ2T L2 SKQ, # to # SKQ, #1 Q 1 2 (2) area (mm 2 ) Nylon Urethane Note1) 1: max. diameter Note2) ( ): Valves for soft nylon. Different diameter tee: KQ2T L Q 1 2 area (mm 2 ) a b Nylon Urethane KQ2T0-0 KQ2T0-0 KQ2T KQ2T Note1) : max. diameter Cross: KQ2TW Different diameter cross: KQ2TX L Nylon Urethane KQ2TW0-00 KQ2TW KQ2TW KQ2TW KQ2TW a b KQ2TX0-0 KQ2TX0- KQ2TX L 2 Q Q area (mm 2 ) Note1) : max. diameter area (mm 2 ) Nylon Urethane Note1) : max. diameter 1 2 K D S T 2.1-

22 Series KQ2 Different diameter cross: KQ2TY a b KQ2TY0-0 KQ2TY0- KQ2TY L 2 Q area (mm 2 ) Nylon Urethane Note1) : max. diameter 2 5 ale run tee: KQ2Y <5> <> <R(PT)>.2 1 (2) L1 L2 A 1 2 L area (mm 2 ) R(PT) (ex.) Nylon Urethane 5 X 0. KQ2Y KQ2Y2-01S 1 9. KQ2Y2-02S X 0. KQ2Y X 1.0 KQ2Y0-1. KQ2Y0-01S KQ2Y0-02S X 0. KQ2Y X 1.0 KQ2Y0-. KQ2Y0-01S 2 9 KQ2Y0-02S KQ2Y0-0S 29 KQ2Y0-01S KQ2Y0-02S KQ2Y0-0S 0.5 KQ2Y-01S KQ2Y-02S KQ2Y-0S KQ2Y-0S 5.5 KQ2Y-02S KQ2Y-0S KQ2Y-0S 5.5 KQ2Y1-0S KQ2Y1-0S 1 11 (11) 11 SKQ1, #1 to #2 Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter Note2) ( ): Values for soft nylon <5, > <R(PT)> 2.1-2

23 One-touch Fittings Series KQ2 ale delta: KQ2D <5, > <R(PT)> Delta union: KQ2D L1 L2 Q area (mm 2 ) A R(PT) (ex.) Nylon Urethane 5 X 0. KQ2D X 1.0 KQ2D KQ2D0-01S KQ2D0-02S X 0. KQ2D0-5 2 X 1.0 KQ2D0-1.. KQ2D0-01S KQ2D0-02S KQ2D0-0S.5.5 KQ2D0-01S.5 KQ2D0-02S KQ2D0-0S KQ2D-02S KQ2D-0S KQ2D-0S 5 2 KQ2D-02S KQ2D-0S KQ2D-0S.5 SKQ, #1 to #1 Reference dimensions after R(PT) thread installation. Note1) : max. diameter L KQ2D0-00 KQ2D KQ2D KQ2D KQ2D SKQ, # to #2 Note1) : max. diameter Q <5, > <R(PT)> area (mm 2 ) Nylon Urethane Branch Y : KQ2U <5, > <R(PT)>.2 1 (2) P area (mm 2 ) L A R(PT) (ex.) Nylon Urethane 5 X 0. KQ2U KQ2U2-01S KQ2U2-02S X 0. KQ2U X 1.0 KQ2U KQ2U0-01S KQ2U0-02S X 0. KQ2U0-5 X 1.0 KQ2U KQ2U0-01S KQ2U0-02S KQ2U0-0S 5.5 KQ2U0-01S KQ2U0-02S KQ2U0-0S KQ2U-02S KQ2U-0S KQ2U-0S KQ2U-02S KQ2U-0S KQ2U-0S KQ2U1-0S KQ2U1-0S (9) 111 KQ2U2 to KQ2U KQ2U1 SKQ1, #1 to # SKQ, #1 Reference dimensions after R(PT) thread installation. Note1) : max. diameter Note2) ( ): Values for soft nylon <5, > <R(PT)> K D S T

24 Series KQ2 Delta branch: KQ2UD 1 2 L I Q P area (mm R(PT) (ex.) 2 ) A Nylon Urethane KQ2UD0-01S KQ2UD0-02S KQ2UD0-01S KQ2UD0-02S SKQ1, # to #25 Reference dimensions after R(PT) thread installation. Note1) 1: max. diameter Union Y : KQ2U.2 L1 L2 Q Nylon Urethane KQ2U2-00 KQ2U0-00 KQ2U KQ2U KQ2U KQ2U KQ2U (9) 5 KQ2U2 to KQU KQ2U1 Different diameter union Y : KQ2U b a.2 P SKQ, #1 to # SKQ, #1 1 2 L1 area (mm 2 ) (2) Note1) : max. diameter Note2) ( ): Values for soft nylon. Q 1 Nylon Urethane KQ2U2-0 KQ2U0-0 KQ2U KQ2U L2 P 2 area (mm 2 ) KQ2U KQ2U KQ2U2 to KQU SKQ, # to #11 Note1) 1, 2: max. diameter KQ2U SKQ, # Different diameter double union Y : KQ2UD a b KQ2UD0-0 KQ2UD0-0 SKQ, #2 to # L L P.. I 2 Q area (mm 2 ) Nylon Urethane Note1) 1, 2: max. diameter

25 One-touch Fittings Series KQ2 Plug-in Y : KQ2U Fitting size ød L1 L2.2.2 KQ2U2-99 KQ2U0-99 KQ2U KQ2U KQ2U KQ2U KQ2U (9) KQ2U2 to KQU KQ2U1 P SKQ, #1 to # SKQ, #1 Q A (2) area (mm 2 ) Nylon Urethane Note1) : max. diameter Note2) ( ): Values for soft nylon. Double plug-in Y : KQ2XD Fitting size ød 1 2 L1 L2 I Q A P area (mm 2 ) Nylon Urethane KQ2XD0-0. KQ2XD0-0. SKQ, #20, # Note1) 1: max. diameter 2 Different diameter plug-in Y : KQ2X Fitting size 1 2 L1 L2 A P Q area (mm 2 ) ød Nylon Urethane KQ2X0-0 KQ2X KQ2X KQ2X SKQ, # to #25 Note1) 1: max. diameter K D S T 2.1-2

26 Series KQ2 Plug-in reducer: KQ2R Bulkhead union: KQ2E (2) Fitting size L A area (mm 2 ) ød Nylon Urethane.2 KQ2R KQ2R KQ2R KQ2R KQ2R0-0. KQ2R KQ2R KQ2R KQ2R KQ2R0-2. KQ2R KQ2R (29.5) 2 1 KQ2R (.1) SKQ20, #1 to #1 Note1) : max. diameter Note2) ( ): Values for soft nylon. T L area (mm 2 ) () (ex.) Nylon Urethane.2 KQ2E2-00 KQ2E0-00 X 1 X KQ2E X KQ2E X KQ2E-00 KQ2E-00 KQ2E X 1 X 1 2 X (9) SKQ20, #1 to #20 Note1) ( ): Values for soft nylon. ounting hole Bulkhead male elbow: KQ2LE 1 2 T B E area (mm 2 ) (ex.) (ex.) Nylon Urethane KQ2LE0-00 X KQ2LE X KQ2LE X KQ2LE-00 KQ2LE X 1 X SKQ20, # to #25 Note1) : max. diameter ounting hole Bulkhead connector: KQ2E T 1 2 L1 L2 area (mm 2 ) Rc(PT) () (ex.) (ex.) Nylon Urethane.2 KQ2E2-02 X KQ2E X KQ2E KQ2E KQ2E X KQ2E KQ2E KQ2E X KQ2E0-0 5 KQ2E X KQ2E-0.5 KQ2E X KQ2E KQ2E X (9) KQ2E SKQ20, #2 to #0 Note1) ( ): Values for soft nylon. ounting hole 2.1-2

27 One-touch Fittings Series KQ2 Adaptor: KQ2N Fitting size R(PT) 5 X 0. 5 X 0. (ex.) KQ2N0-5 KQ2N0-01S KQ2N0-5 KQ2N0-01S KQ2N0-02S 1 KQ2N0-02S 1 KQ2N0-0S KQ2N-0S L A ød Nipple: KQ2N cap: KQ2C Fitting size Reducer nipple: KQ2N Color cap: KQ2C L ød 1 2 KQ2N0-99 KQ2N KQ2N KQ2N KQ2N KQ2N Fitting size L 1 2 ød a b KQ2N0-0 KQ2N KQ2N KQ2N KQ2N L KQ2C0-00 KQ2C KQ2C KQ2C KQ2C KQ2C Note1) : max. diameter Plug: KQ2P, KQP KQ2C L KQ2C-0A KQ2C-0B KQ2C KQ2C-0A KQ2C-0B KQ2C KQ2C KQ2C KQ2C B (black), R (red), YR (orange), BR (brown), Y (yellow), G (green), CB (sky blue), GR (gray), W (white), BU (blue) KQ, KQ20-5, KQS, KQ2S0-5, KQL, KQ2L0-5, KQT, KQ2T0-5, KQY, KQ2Y0-5, KQ, KQ20-5, KQS, KQ2S0-5, KQL, KQ2L0-5, KQT, KQ2T0-5, KQY, KQ2Y0-5, K D S T Fitting size ød.2 KQ2P-2 KQP KQ2P-0 KQ2P-0 KQP-0 KQP KQ2P-0 KQP KQ2P- KQP-.5 KQ2P- KQP KQ2P-1 KQP-0.9 Note) KQ2P (white), KQP (blue) L A 2.1-2

28 Series KQ2 ade to Order Consult SC for detailed specifications, dimentions and delivery. Order ade qoil free applications Vaseline T is used as lubricant. For use in oil free applications, for example, paint air lines. Specifications Dimensions ow to Order Same as Series KQ2. Same as Series KQ2. Add -X at the end of the standard part number. (Example: KQ X ) wstainless One-touch fittings For use in highiy corrosive atmospheres where brass is not acceptable. Specifications Dimensions aterials in each part ow to Order Same as series KQ2. Same as series KQ2. (Some may be different, consult SC) Body Stud Chuck Guide Collet, Release button Packing, O ring SUS, PBT SUS ( portion) SUS0 SUS, PO PO NBR Every one of SUS0, SUS0 and SUS1 is possible to use. Consult SC

29 One-touch Fittings anifold Series K Compact piping. any varieties (0 types) available. One-touch fittings give the most efficient operation. K11 K K odel odel K11 K K1 K1 K K1 Port A One-touch fitting One-touch fitting One-touch fitting One-touch fitting One-touch fitting One-touch fitting Porting Port B One-touch fitting Rc(PT)female thread One-touch fitting One-touch fitting R(PT)male thread One-touch fitting Rod One-touch fitting Number of Port A,, Port B size ø ø ø Rc(PT) Rc(PT) ø ø ø ø, R(PT) ø, R(PT) ø, R(PT) ø,r(pt) ø, R(PT) ø, R(PT) ø, R(PT) ø, R(PT) ø, R(PT) ø ø ø ø ø Port A size ø ø ø K1 K1 K1 Applicable Tubing material Nylon, Soft nylon, Polyurethane ø, ø, ø, ø, ø Specifications odel K11 K K1 K1 K K1 Fluid ax. operating pressure Proof pressure Ambient and fluid temperature Air, Water 1.0Pa.0Pa 5 to 0 C, Water: 0 to 0 C (No freezing) JIS B020 (Taper thread) JIS B020 (Taper thread) Accessories None exagon socket head blank plug with sealant: 1 pc. None None None None Note1) Applicable for general industry water. Consult SC if using for other kinds of fluid. Surge pressure must be under the max. operating pressure. Component aterials odel K11 K K1 K1 K K1 Body PBT Stud C0BD C0BD C0BD PBT Chuck Guide Collet, Release button Packing, O ring Stainless steel (SUS0) C0BD, Stainless steel (SUS0) Polyacetal (PO) NBR 2.1-5

30 One-touch Fittings anifold Series K Construction K11 K Port A: One-touch fitting Port B: One-touch fitting Port A: One-touch fitting Port B: Rc(PT) female thread K1 K1 K Port A: One-touch fitting Port B: One-touch fitting K1 Port A: One-touch fitting Port B: One-touch fitting, R(PT) male thread Port A: One-touch fitting Port B: One-touch fitting stud Port A: One-touch fitting Port B: One-touch fitting K D S T 2.1-

31 Series K K11 FA FB N L1 K K K K K K L L L L L P. 1.5 Q Q A B 1.5 Port B min. port size K SK, #1 to # K1 F Rc(PT) T N K K K K K-0-0- K-0-0- (ex.) L L L L L L P. 1.5 Port B Q1 Q2 min. port size SK, # to # a b 1 2 K K K K K L1 L2 L P Q1 Q Port B min. port size Use Series K

32 One-touch Fittings anifold Series K K1 a b K R(PT) Port B 1 2 L1 L2 L P A Q1 Q2 1 2 (ex.) min. port size K S- 1 1 K S K S-.5.5 K S K S K S-.5 1 K S- 0.5 K S K S- 9 K S K1-0--0S K1-0--0S- 92 K S- 9 K1-0--0S K1-0--0S Precautions for the use with One-touch fittings Caution Refer to Air Fittings & Tubing Precautions for the details of installation/removal of One-touch fittings. Fitting size a b ød K1 1 2 K K K K K L1 L2 L P Q1 Q2 A A B Port B min. port size K D S T a b K K K L1 L L 1 L 11 P 1.5 Q1 50 Q Port B min. port size

33 iniature Fittings, 5, R(PT)1/ Series ose nipple Barb fitting Barb Easy tube insertion igh retaining force PAT. Body Electroless nickel plated Gasket Low clamping torque Either nylon, soft nylon and polyurethane tubing. Barb Easy tube insertion igh retaining force Cap nut ose nipple tubing connection/disconnection Body is simple while keeping Electroless nickel a large retaining force. plated Electroless nickel plated. Gasket Low clamping torque Certain sealing effect Simple Connection/ Disconnection ose nipple tubing connection/ disconnection is simple while keeping a large retaining force. iniature Size For air connection in confined areas. Accepts any Styles of Plastic Tubing ose nipple and hose elbow accepts nylon, soft nylon, and polyurethane tubing. Specifications Applicable tube material Applicable tube dia. 5-R(PT) ax. operating pressure (at 20 C) Port size Component aterials aterial Body Gasket Nylon ø/ø ø/ø Soft nylon ø/ø ø.1/ø2.1 ø/ø ø/ø Polyurethane ø.1/ø2, ø/ø ø.1/ø2, ø/ø, ø/ø 1.5Pa 1.0Pa 0.Pa, 5, R(PT) JIS B0209 Class 2 (etric coarse thread), JIS B020 (Taper pipe thread) C0BD (Nipple -N, -5N: Stainless steel (SUS 0)) PVC, Nylon: GF0% Fitting arkings for Applicable aterial (Barb fitting, Barb elbow, Barb elbow ()) material determines the compatible fittings. (See diagram below.) Connection Fitting marking for applicable tube material Barb fitting Barb elbow Barb elbow () Surface treatment (Color) Soft nylon tube Polyurethane tube Electroless nickel plated (Silver color) R(PT), 5 Nylon tube Soft nylon tube Polyurethane tube Electroless nickel plated (Silver color) Electroless nickel plated (Black color) [Except stud] 2.1-

34 iniature Fittings Series Series, R(PT)1/ Series 5 Series/odel Style Application Note Series/odel Style Application Note Series/odel Style Application Note Barb fitting ø.1/2.1 Barb fitting Tee ø/ X -5AN- -AU- For nylon X Both sides ø.1/2-5t tube allows 90 X connection -AU- -ALU- -ALU- -UL -UT -N -P -G Series/odel P Barb fitting P Universal elbow P Universal tee P Nipple P Plug P Gasket P Barb fitting -01AN- -01AN- P Barb fitting -01AU- R (PT) -01AU- P ose nipple For soft nylon tube For polyurethane tube For soft nylon and polyurethane tube Soft nylon tube Body rotates 0 around the stud axis. polyurethane soft nylon and polyurethane Body rotates at 0 around the stud axis Body rotates at 0 around the stud axis Fitting to workpiece and fitting - fitting connection possible To plug unused port To seal thread ø/ X ø.1/2.1 X ø.1/2 X ø/ X female X male female X female X male male X male Style Application Note P For nylon tube For soft nylon and polyurethane tube For nylon, soft nylon and polyurethane tube ø/ X R(PT)1/ ø/ X R(PT)1/ ø/ X R(PT)1/ ø/ X R(PT)1/ ø/ X R(PT)1/ ø/ X R(PT)1/ -5AN- -5AU- P Barb fitting For soft nylon tube For polyurethane tube ø/ X 5 ø.1/2.1 X 5 ø.1/2 X 5 ø/ -5AU- For soft nylon X 5 and polyurethane tube ø/ -5AU- P X 5 Barb elbow ø/ -5ALN- For nylon tube X 5 Body rotates at 0 ø/ -5ALN- around stud X 5 P Barb elbow soft ø.1/2.1 nylon Body X 5-5ALU- rotates polyurethane X ø.1/2 at 0 5 around -5ALU- the soft stud nylon and polyurethane axis -5ALU- P Barb elbow () Body -5ALN- rotates at 0 For nylon around tube 5 the -5ALN- stud P axis -5ALU- -5ALU- Barb elbow () -5ALU- P ose nipple L- P Elbow P soft nylon Body rotates polyurethane at 0 around the stud axis soft nylon and polyurethane For nylon, soft nylon, and polyurethane tube -5- P ose elbow -5L- For nylon, soft nylon, and -5L- polyurethane P tube ose elbow () Body rotates -5L- -5L at 0 around the stud axis One-sided 90 elbow ø/ X 5 ø/ X 5 ø/ X 5 ø/ X 5 ø.1/2.1 X 5 ø.1/2 X 5 ø/ X 5 ø/ X 5 ø/ X 5 ø/ X 5 ø/ X 5 ø/ X 5 ø/ X 5 ø/ X 5 5 female X 5 female 5-5UL -5UT -5J -5N -5UN -5E -5ER -5-5B -5P -5G1-5G P Universal elbow P Universal tee P Extention fitting P Nipple P Union nipple P Bulkhead union P Bulkhead reducer P anifold Reducer bushing Plug Gasket P Gasket () Body rotates at 0 around the stud axis Body rotates at 0 around the stud axis Solid piece moves fitting up from workpiece Fitting to workpiece and fitting - fitting connection Body rotates at 0 around the stud axis Panel mount connection Reduction from Rc(PT)1/ to 5 and includes panel mounting 5 female P P P P Rc(PT)1/ can be diverted in up to 9, 5 stations, includes panel or bracket mounting For reducing Rc(PT)1/ female to To plug unused 5 port To seal 5 thread -5AL - -5AL - -5L-, -5L-, 5 female X 5 female X 5 female 5 female X 5 male 5 female X 5 female X 5 male 5 male X 5 female 5 male X 5 male 5 male X 5 male PAT 5 female X 5 female Rc(PT)1/ X 5 female Rc(PT)1/ X 5 female (9 stations) Rc(PT)1/ X 5 female aterial: PVC aterial: Nylon GF0% K D S T 2.1-

35 Series Series Barb fitting for soft tube: -AU- Barb fitting for soft tube: -AU- area: 0.9mm 2 Barb elbow for soft tube: -ALU- : 0.g area: 0.9mm 2 : 0.g Barb elbow for soft tube: -ALU- Universal elbow: -UL area: 0.mm 2 : 0.g Universal tee: -UT area: 0.mm 2 : 0.9g Nipple: -N area: 0.mm 2 : 1.g Gasket: -G area: 0.mm 2 : 1.g Plug: -P SA, #1 to # : 0.g area: 0.9mm 2 : 0.005g : 0.5g Series R(PT)1/ Barb fitting for nylon tube, soft tube: -01A -, - -01AN- Nylon tube -01AN- -01AU- Soft tube -01AU- SA, # to #11 A B 5 5 øc area (mm 2 ) ose nipple: -01-, SA, #/#1 A B øc E area (mm 2 )

36 iniature Fittings Series Series 5 Barb fitting for nylon tube: -5AN-, - -5AN- -5AN- S5B, #1/#2 A 1 B 5 øc 1. area (mm 2 ) Barb fitting for soft tube: -5AU-, -, - A B øc area (mm 2 ) -5AU AU- -5AU S5B, # to #5 Barb elbow for nylon tube: -5ALN-, - Barb elbow for soft tube: -5ALU-, -, - A B -5ALN- -5ALN- -5ALU- -5ALU- -5ALU S5B, # to # C area (mm 2 ) ALN- -5ALU-, - -5ALN- -5ALU- Barb elbow for nylon tube: -5ALN-, - Barb elbow for soft tube: -5ALU-, -, - -5ALN- -5ALN- -5ALU- -5ALU- -5ALU- ose nipple: -5-, - A B S5B, #11 to # A B S5B, #1/# C C area (mm 2 ) øe area (mm 2 ) ALN- -5ALU-, - -5ALN- -5ALU K D S T

37 Series Series 5 ose elbow: -5L-, - -5L- -5L- A S5B, #1/# B C D øe 1. øf.5.5 area (mm 2 ) ose elbow: -5L-, - -5L- -5L- A.5.5 B 1.5 S5B, #20/# C D øe 1. øf.5.5 G I area (mm 2 ) Elbow: -5L Tee: -5T Universal elbow: -5UL :.2g Universal tee: -5UT :.5g Extension fitting: -5J area: 2.mm 2 : 5.g Nipple: -5N area: 2.mm 2 :.g area:.0mm 2 :.g area:.0mm 2 Universal nipple: -5UN Bulkhead union: -5E : 1.5g area:.0mm 2 :.9g For the plate thickness.5 to mm, give the plate tapping X 0.5, and then screw-in. :.g S5B, # to #

38 iniature Fittings Series Series 5 Bulkhead reducer: -5ER anifold: -5 Bushing: -5B For the plate thickness.5 to mm, give the plate tapping X 0.5, and then screw-in. : g Plug: -5P Panel mounting plate thickness max..5mm For the plate thickness.5 to mm, give the plate tapping X 0.5, and then screw-in. : 59g Gasket: -5G1 : 5.g Gasket: -5G : 1.g : 0.01g : 0.0g S5B, #2 to #1 Precautions Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Tightening of or 5 thread Use of tubing with hose nipple Use of tube with barb fitting K Caution qtighten by hand, and give it an additional 1/ rotation with wrench. (The additional rotation should be doubled to 1/2 when using the universal elbow, universal tee, etc. which have two gaskets.) If tightened too much, thread portion may be damaged and gasket may be deformed. This will cause air leakage. On the contrary, if tightening is not sufficient, thread may loosen causing air leakage. Caution qcut the tube perpendicularly to the tube axis to a little longer length than required length. (Use tube cutter TK-1, TK-2 or TK-.) wpass the tubing through the cap nut. epush the tube until it comes to the end of the barb portion, or it may cause air leakage or hose releasing. rtighten the cap nut firmly by hand on the fitting. Caution qcut the tube perpendicularly to the tube axis with a little longer length than required length. (Use tube cutter TK-1, TK-2 or TK-.) wpush the tube in until it comes to the end of the barb portion, or it may cause air leakage or hose releasing. D S T

39 Self-seal Fittings Series KC Before Insertion of After Insertion of Spring O ring Retainer Valve Built-in self-seal mechanism Air does not exhaust after removal of tube. Stopper Cushion Release button O ring Body Guide Collet Chuck With sealant Standard Stud Rotates for simple piping in confined areas. PAT. One-touch fitting (With built-in selfseal mechanism) to prevent air exhaust when removing tube. Best for multiple use areas when pressure cannot be shut down. styles are available. Electroless nickel plated for copper-free applications. Applicable Tubing material Specifications Operating fluid ax. operating pressure Proof pressure Ambient and fluid temperature portion Nut Sealant ( portion) Copper-free application Component aterials Body Stud Chuck, Spring Guide Collet, Release button Valve, Retainer Stopper Packing, O ring Nylon, Soft nylon, Polyurethane ø, ø, ø, ø, ø Air 1.0Pa.0Pa 5 to 0 C (No freezing) JIB B020 (Taper pipe thread) JIB B01 Class 2 (etric fine thread) With sealant (Standard) All brass parts with electroless nickel plated C0BD, PBT C0BD ( portion) Stainless Steel (SUS0) SUS0, C0BD, Polyacetal (PO) Polyacetal (PO) Polyacetal (PO) C0BD, Polyacetal (PO) NBR

40 Self-seal Fittings Series KC odel ale connector KC P Used to pipe in the same direction from female threaded portion. Straight union KC P.2.1- Used to connect tubes in the same direction. One of two ports has a self-seal function. ale elbow KCL P Used to pipe in right angles to female threaded portion. ost common style. Straight plug for frequent use KC P.2.1- Used to connect a selfseal fitting and a tube in the same direction. It can save the tube cutting labor in the case of frequent tube installation and removal. Union tee KCT P Used to connect tubes in both 90 directions. Elbow plug for frequent use KCL P.2.1- Used to pipe a tube at right angles to a self-seal fitting. It can save the tube cutting labor in the case of frequent tube installation and removal. Union Y KCU P Used to connect tubes in the same direction.2 branched ports has a self-seal function. Check adaptor KCJ P.2.1- Used to add the self-seal mechanism to the usual Onetouch fittings, Series KQ. Bulkhead union KCE P.2.1- Used for junction connection of tubes for installation on a panel. One of two ports has a self-seal function. Bulkhead female union KCE P.2.1- Used for transit connection of a tube and a male screw for installation on a panel. K D S T 2.1-0

41 Series KC Precautions Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Insertion and Removal from Self-seal Fitting Caution Installing qcut the tube perpendicularly, taking care not to damage the outside surface. (Use tube cutter TK-1, 2 or. Do not cut the tube with cutting pliers, nippers, scissors, etc.) Flat or angled cuts will make it difficult to connect to fittings or, if connected, tube will release or air leakage will occur. wgrasp the tube, then slowly push it until it comes to a stop. epull it back gently to make sure that it has a positive seal. Incomplete installation may cause air leakage or tube release. Removing qpush the release button into the fitting. The button should be pushed evenly. wpull out the tube while keeping the release button depressed. (If the release button is not held down, the tube cannot be withdrawn.) eto reuse the tubing, cut off the previously lodged portion of the tube. If using tubing without cutting the damaged portion off, it may cause the air leakage or make it difficult to release the tube. The Number of Insertions and Removals from Self-seal Fitting Caution qthe number of insertions and removals as a rough quide is as follows. 00 times etal stem 00 times Installation of Self-seal Fitting Caution qthe fitting should be installed (Installation of R (PT) thread portion) by screwing with a spanner at the hexagonal portion of the body. The position of spanner should be a root as close as possible to R (PT) thread. Use the spanner corresponding to the size of hexagonal portion, or hexagonal portion may be deformed. Tightening the thread portion of an 5 size fitting Caution qfirst, tighten it by hand, then give it an additional 1/ turn with a wrench. Excessive tightening may damage the threaded portion or deform the gasket to cause air leakage. Insufficient tightening may leave the thread loosened or cause air leakage. Distinction of plug and applicable fitting Caution qthe applicable fitting should be chosen depending on the style of plug. Check adaptor ow to use: Use it for addition of selfseal mechanism to a standard Onetouch fitting series KQ. Self-seal fittings with check adaptor are not available. It causes the air leakage. Check adaptor KCJ -99 One-touch fitting series KQ Elbow plug for frequent use, straight plug for frequent use. ow to use: For use in the case of frequent tube installation and removing, tube cutting labor can be saved. These plugs are not available for a standard One-touch fittings Series KQ. If trying to install the plug into a KQ, plug will jump out of the fitting. Note the exclusive marking for self-seal fittings before use. Elbow plug for frequent use KCL -99 arking arking exclusive to self-seal fitting Straight plug for frequent use KC -99 Caution Self-seal fitting Series KC Built-in self-seal mechanism Insertion and Removal under a pressurized condition qwhen inserting/removing of the tube is difficult under a pressurized condition, it should be inserted or removed by lowering the pressure or after fully exhausting

42 Self-seal Fittings Series KC ale connector: KC <5> <R(PT)> R(PT) 5 X 0. 5 X 0. KC0-5 KC0-01S KC0-5 KC0-01S KC0-02S KC0-01S KC0-02S KC0-0S KC-02S KC-0S KC-0S KC-0S (ex.) L A area (mm 2 ) Nylon Urethane Reference dimensions after R(PT) installation. <5> <R(PT)> ale elbow: KCL Union tee: KCT R(PT) 5 X 0. 5 X 0. KCL0-5 KCL0-01S KCL0-5 KCL0-01S KCL0-02S KCL0-01S KCL0-02S KCL0-0S KCL-02S KCL-0S KCL-0S KCL-0S KCT0-00 KCT0-00 KCT0-00 KCT-00 KCT-00 (ex.) L1 L L Q A area (mm 2 ) Nylon Urethane Note1) : max. diameter area (mm 2 ) Nylon Urethane Reference dimensions after R(PT) installation. Note1) 1: max. diameter K Union Y : KCU KCU0-00 KCU0-00 KCU0-00 KCU-00 KCU L L P Q area (mm 2 ) Nylon Urethane Note1) : max. diameter 1 9 D S T 2.1-2

43 Series KC Check adaptor: KCJ KCJ0-99 KCJ0-99 KCJ0-99 KCJ-99 KCJ-99 ød L A area (mm 2 ) Nylon Urethane Note1) : max. diameter Bulkhead union: KCE KCE0-00 KCE0-00 KCE0-00 KCE-00 KCE-00 T () X 1 1 X 1 1 X 1 20 X 1 X 1 (ex.) L ounting hole area (mm 2 ) Nylon Urethane Bulkhead female union: KCE Rc (PT) KCE0-02 KCE0-02 KCE0-0 KCE-0 KCE-0 T () X 1 1 X 1 1 X 1 20 X 1 X L1 (ex.) (ex.) L ounting hole area (mm 2 ) Nylon Urethane Straight union: KC KC0-00 KC0-00 KC0-00 KC-00 KC L area (mm 2 ) Nylon Urethane Note1) : max. diameter Straight plug for frequent use: KC KC0-99 KC0-99 KC0-99 KC-99 KC-99 ød L A area (mm 2 ) Nylon Urethane Note1) : max. diameter

44 Self-seal Fittings Series KC Elbow plug for frequent use: KCL KCL0-99 KCL0-99 KCL0-99 KCL-99 KCL-99 ød L L A area (mm 2 ) Nylon Urethane Note1) 1, 2: max. diameter 25 0 K D S T 2.1-

45 ulti-connector Series D The use of the multi-connector enables panel mount connections with other apparatus and can provide the reliability of one-touch installation and removal of multi-tubes(nylon, polyurethane). As a result, separate transportation of panel and machinery equipment and backup unit exchange are made possible. One-touch installation and removal Employs the unique built-in keying mechanism which provides one-touch installation and removal capability even in hard to see locations. In addition, it prevents installation mistakes when re-connecting. Installation processes are reduced considerably As compared with the use of many bulkhead unions, this installation is very easy and installation time is reduced considerably. Reliable tube retaining force This construction mechanism enables clamping and unclamping every tube in use by one operation and can provide a reliable tube retaining force. Number of connecting tubes 2 styles - tubes & tubes. D Plug odel Socket case Easy insertion of tube by the floating mechanism to adjust to the case hole. Clamp bolt Possible to clamp with one bolt at once. PAT. No. of connecting tubes U packing Tight seal. ulticonnector D-0N D-0NU D-0N D-0NU D-0N D-0NU D-0N D-0NU Specifications Socket side Plug side only DP-0N DP-0NU DP-0N DP-0NU DP-0N DP-0NU DP-0N DP-0NU Operating fluid ax. operating pressure Ambient and fluid temperature Plate Spacer Socket side only DS-0N DS-0NU DS-0N DS-0NU DS-0N DS-0NU DS-0N DS-0NU Socket Plug case old surely by inserting the both of tube and barb. Possible to connect in the required position by the convex and concave for engagement. Plug side Nylon T025 T00 T00 T05 T025 T00 T00 T05 Cover Stopper (With expander) Possible to insert smoothly by expansion of tube with expander. older Clamp ring Connect within one turning from the socket side to the plug side. Applicable tubing Soft nylon TS025 TS00 TS025 TS00 Polyurethane TU025 TU00 TU025 TU00 Air 1.0Pa 5 to 0 C (No freezing) Accessories (optional) D-C- D-C- Component aterials Socket case, Plug case, Clamp ring Plate older Socket, Plug, Stopper U packing Cover Cross recessed head screw, Clamp bolt Spacer ADC Black anodized SPCC, Chromated SPCC, Zinc chromated C0BD NBR CR SWR Zinc chromated SPC Zinc chromated D 2.1-5

46 ulti-connector Series D ow to Use Caution Removing Loosen clamp ring q, and separate the multiconnector into two parts, socket side and plug side. Clamping of tube qafter inserting tube, tighten clamp bolt y clockwise with a screwdriver. wbarb cassette creeps into the direction D and the tube will be clamped at the B clamp portion t consisting of barb e and case. Insertion and removal of tube qturn the clamp bolt y to the left with a screwdriver, loosen until the stopper w touches the case e, and barb cassette r will be pulled out in the direction A.Then clamp portion B, consisting of barb t and case e, will be freed. Next, insert or remove the tube. wthe corresponding numbers are stamped on both the socket and plug sides for each tube connection. eif it is hard to insert the tube, enlarge the tube end with the head of stopper, expander C, before inserting tube. rinsert tube until it clears mountain of barb t completely. Connection qpush together and rotate both of the cases, and the plug side will slide into the socket side at the proper position. wthe ring E, male and female, of the plug side and socket side will interlock with each other at the proper position by pushing together and rotating. efinal process of connection is to screw-in the clamp ring. Cover mounting qcover is mountable on both sides, plug side and socket side. wenlarge cover and mount cover onto mounting area. ow to Order D Number of connecting tubes Style P S ulti-connector Plug side Socket side 0 mm 0 mm 0 N material N Nylon Soft nylon NU Polyurethane Accessories (optional) C1 1 cover (One side) C2 2 covers (Both sides) K D S T 2.1-

47 Series D Dimensions/D, D Panel mounting hole (with the cover at socket side) Panel mounting hole D Panel mounting hole (with the cover at socket side) Panel mounting hole D-0N D-0N D-0NU D-0NU D-0N D-0N D-0NU D-0NU Barb I.D. (d) A B

48 ulti-connector Series D Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Caution Precautions Insertion of tube qbe sure to insert the tube slowly so that you will feel it move smoothly and can feel it touch the end. Once the tube has been properly inserted, pull it back gently, to make sure that it has a positive seal. If not inserted properly, it may cause the air leakage or tube releasing. win case the number of tubes to be used is less than (D) or (D), the positioning of the tube should be symmetrical to the center. K D S T 2.1-

49 Rectangular ulti-connector Connecting :, 20 Series KD ulti-connector is effective in saving labor for separate transportation of the panel and the machine and for exchanging units due to failure. Substantial reduction in mounting space In comparison with a model requiring many union joints for panels and partitions, this model needs only a small space. One-touch connection/ disconnection of connector ultiple pipes can be connected/disconnected in one-touch opperation without connection error. Thus man-hours for connection/disconnection is cut down substantially. One-touch tube connection One-touch fittings substantially cuts down man-hours for piping. KD20 Plug connector Socket connector Packing Usable from vacuum to 1Pa. odel Plate PAT.PEND Screw for bracket E type snap ring With One-touch fittings etric size: ø.2, ø, ø, ø Applicable to non-copper style (nickel plated) s of different sizes can be used simultaneously. Two types, with and 20 connector tubes, are available. Panel mounting bracket (Standard) Operation on the panel front permits mounting. oles for mounting bolts are not necessary. (ountable panel thickness is 5mm maximum.) Clamp bolt Socket case Plug case Irregular shape permits engagement in a proper position. No. of connecting tubes Color of release button ø.2 KD-2 ø KD-0 00g ø KD-0 ø KD-0 520g ø.2 KD20-2 Blue 20 ø KD g ø KD20-0 ø KD g Caution KD Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Applicable Tubing material Specifications Operating fluid ax.operating pressure ax.operating vacuum pressure Proof pressure Ambient and fluid temperature Nylon, Soft nylon, Polyurethane ø.2, ø, ø, ø Air 1.0Pa 0kPa 1.5Pa 5 to 0 C (No freezing) 2.1-9

50 ulti-connector Series KD Component aterials Plug case, Socket case Plate, Bracket Body Chuck Plug connector, Guide Socket connector Collet, Release button Packing Clamp bolt, Screw for bracket, Cross-recessed head machine screw E type snap ring Polyacetal (PO) SPCC Plated PBT, C0BD Electroless nickel plated (ø) SUS0 Stainless steel (SUS0), C0BD Electroless nickel plated, PO (ø) Polyacetal (PO) NBR SWR, Nickel plated Stainless steel (SUS0) Caution ow to Use Separation Loosen the clamp bolt to separate the plug side from the socket side. Part Numbers No.of connecting tubes 20 ø.2 ø ø ø ø.2 ø ø ø Plug Socket KDP-2 KDS-2 KDP-0 KDS-0 KDP-0 KDS-0 KDP-0 KDS-0 KD20P-2 KD20S-2 KD20P-0 KD20S-0 KD20P-0 KD20S-0 KD20P-0 KD20S-0 Color of release button Blue Connection Put together the irregular faces for engagement and connect the plug case to the socket. After tightening the clamp bolt by hand, tighten it further with allen wrench(nominal width across flats: ). ixed Sizes of Plug Connectors and Socket Connectors The rectangular multi-connector permits connector exchange in any desired position, thus allowing use of different sizes of tubes. Panel mounting qloosen () screws for bracket on the socket side using a Phillips screwdriver (JIS nominal No.2) until the bracket touches the stop ring. Part Numbers Connector Plug connector Socket co nnector (With packing) ø.2 ø ø ø ø.2 ø ø ø KDP-2 KDP-0 KDP-0 KDP-0 KDS-2 KDS-0 KDS-0 KDS-0 Color of release button Blue wshift the panel mounting bracket to the inside (ove the screw for bracket in the longitudinal direction of the slot) and put the connector in the panel mounting hole. (Panel mounting hole: See Dimensions.) qloosen the cross-recessed head machine screw using a Phillips screwdriver to remove the plate from the case. wafter exchanging connectors in desired places, fix the plate with a Phillips screwdriver to the case. eafter shifting the bolt for bracket to the outside, tighten the bolt with a Phillips screwdriver to fix the socket case. K D rloosen the screw for bracket until the bracket touches the stop ring and shift the bracket to the inside to remove the connector from the panel. S T 2.1-0

51 Series KD Dimensions KD ( ): Dimensions for KD-0 KD20 ( ): Dimensions for KD20-0 KD SKD2, #1 to # KD20 SKD202, #1 to # ade to Order Contact SC for detailed specifications, dimensions and delivery. ixed tube sizes ixed tube size manifolds are available to meet your individual requirements. Consult your SC sales representative for availability. Other tube sizes size () Number of tubes ø IN ø IN

52 Inch-size One-touch ini Series KJ Applicable Tubing ø 1 /, ø 5 /2, ø 1 / -2UNF, NPT 1 /1, NPT 1 / Guide 1 Guide 2 Chuck Accepts nylon and polyurethane tubes. as large retaining force. Release button (Orange) Low disconnecting force. When the fitting is removed, the chuck and collet are released, thus preventing them from biting into the tube excessively. Unique shape for easy tube release. Packing Can be used for a wide range of pressures from a low vacuum up to a pressure of 1.0Pa. The use of a special profile ensures sealing and reduces resistance when the tube is inserted. PAT.PEND Optimum piping in less space with 20% reduction of the outside diameter sealant as standard Possible to use in application where copper-free material is required. Possible to use in vacuum: 0kPa Applicable Tubing material Specifications Operating fluid ax. operating pressure ax. operating vacuum pressure Proof pressure Ambient and fluid temperature Sealant ( portion) Copper-free specification portion Nut Body (White) O ring Stud Possible to tube in narrower space. The body and threaded portion can turn independently. Stud is electroless nickel plated. Nylon, Soft nylon, Polyurethane ø, ø5 2, ø Air, Water 1.0Pa 0kPa.0Pa 5 to 0 C (Water: 0 to 0 C) (No freezing) ANSI/ASEB (NPT thread), JIS B02 2A, Class 2B (UNF thread) JIS B02 2A, Class 2B (UNF thread) With sealant (Standard) All brass parts electroless nickel plated Note1) Applicable for general industry water. Consult SC if using for other kinds of fluid. Surge pressure must be under the max. operating pressure. Component aterials Body Stud Chuck, Guide 2 Release button, Guide 1 Packing, O ring Gasket SUS0, C0BD, PBT C0BD ( portion) SUS0 PO NBR SUS0, NBR 2.2-1

53 Inch-size One-touch ini Series KJ odel ex. socket head male connector KJS P.2.2- Internal hex. allows thread connection by using a hex. key wrench, for confined spaces. Bulkhead union KJE P.2.2- Used to connect two tubes through a panel. Extended male elbow KJW P When the elbow extends over a standard elbow for ease of connection/ disconnection of tubing. ale connector KJ P.2.- Used to pipe in the same direction from female threaded portion. ost common style. Plug-in elbow KJL P.2.2- Used to change by 90 in a tube fetching direction from Onetouch fittings. Union Y KJU P.2.2- Used connect tubes in the same direction. Female connector KJF P.2.2- Used to pipe from male threaded portion such as pressure gauge. Reducer elbow KJL P Used to change by 90 in tube fetching direction from One-touch fittings and to size down. Different dia. union Y KJU P.2.2- Used to connect tubes with size down in the same direction. Straight union KJ P.2.2- Used to connect tubes in the same direction. Branch tee KJT P Used to branch line from female thread in both 90 directions. Plug-in Y KJU P.2.2- Used to branch tubing in the same direction One-touch fittings. Different dia. straight KJ P.2.2- Used to connect different size tubes. Union tee KJT P.2.2- Used to connect tubes in both 90 directions. Different dia. plug in Y KJX P.2.2- Used branch line of size down in the same direction with Onetouch fittings. ale elbow KJL P.2.2- Used to pipe at right angles to female threaded portion. ost common style. Different dia. tee KJT P.2.2- Used to connect tubes with size down in both 90 directions. Branch Y KJU P.2.2- Used to branch line in the same direction from female thread. Union elbow KJL P.2.2- Used to connect tubes at right angles. ale run tee KJY P.2.2- Used to branch line in the same direction from female thread and in 90 directions. Plug-in reducer KJR P.2.2- Used to change size of One-touch fittings. Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Interchangeability of Series KJ/KQ Caution qdo not use the plug-in KQ Series with the KJ Series, it will not hold. wfor combinations other than the plug-in KQ, they are interchangeable. Precautions Installation and Removal of One-touch ini Fittings Caution Installing qcut the tube perpendicularly, using caution not to damage its surface. (Use tube cutter TK-1, TK-2 or TK-. Do not cut the tube with cutting pliers, nippers, scissors, etc.) w Grasp the tube, then slowly push it until it comes to a stop. e Then pull it back gently to make sure that it does not pull out. Removing (Use one hand for removal.) qold the release button with the thumb and forefinger. wgrasp the tube with the remaining three fingers and palm. ethen pull out the tube by the three fingers and palm while pushing in the release button with the thumb and the forefinger. rto re-use the released tube, cut off the damaged portion of the tube. K D S T 2.2-2

54 Series KJ ale connector: KJ <-2UNF> <NPT> (T) (inch) UNF NPT -2UNF 1 1-2UNF KJ01-2 KJ01-S KJ01-S KJ0-2 KJ0-S KJ0-S KJ0-2 KJ0-S KJ0-S (ex.) UNF Reference dimensions after NPT thread installation. L A in. hole dia <-2UNF> <NPT> exagon socket head male connector: KJS <-2UNF> <NPT> (inch) 5 2 (T) UNF NPT -2UNF -2UNF 1 1 KJS01-2 KJS0-2 KJS0-S KJS0-S KJS0-2 KJS0-S (ex.) UNF KJS0-S Reference dimensions after NPT thread installation. Note1) : max. diameter L. 1.. A in. hole dia <-2UNF> <NPT> Female connector: KJF (inch) (T) UNF 5 2-2UNF -2UNF -2UNF KJF01-2 KJF0-2 KJF0-2 Note1) : max. diameter (ex.) L1 L in. hole dia Straight union: KJ (inch) KJ KJ KJ Note1) : max. diameter L in. hole dia

55 Inch-size One-touch ini Series KJ Different diameter straight: KJ (inch) in. 1 2 L 1 2 hole dia. a b KJ KJ KJ Note1) 1, 2: max. diameter ale elbow: KJL <-2UNF> <NPT> (inch) (T) UNF NPT -2UNF (ex.) KJL KJL01-S KJL01-S UNF KJL KJL0-S KJL0-S UNF KJL KJL0-S KJL0-S Reference dimensions after NPT thread installation. Note1) : max. diameter L1 L2 A in. hole dia <-2UNF> <NPT> Union elbow: KJL (inch) 5 2 KJL01-00 KJL0-00 KJL Note1) : max. diameter L Q in. hole dia K Plug-in elbow: KJL (inch) Fitting size ød (inch) KJL01-99 KJL0-99 KJL0-99 Note1) 1: max. diameter L L A in. hole dia D S T 2.2-

56 Series KJ Reducer elbow: KJL (inch) Fitting size ød (inch) KJL01-0 KJL KJL0-0 Note1) 1: max. diameter L L A in. hole dia Extended male elbow: KJW <-2UNF> <NPT> (inch) (T) UNF NPT -2UNF -2UNF 1 1-2UNF 1 1 KJW01-2 KJW01-S KJW01-S KJW0-2 KJW0-S KJW0-S KJW0-2 KJW0-S KJW0-S (ex.) Reference dimensions after NPT thread installation. Note1) : max. diameter L L2 A in. hole dia <-2UNF> <NPT> ale branch tee: KJT <-2UNF> <NPT> (inch) (T) UNF NPT -2UNF -2UNF 1 1-2UNF 1 1 KJT01-2 KJT01-S KJT01-S KJT0-2 KJT0-S KJT0-S KJT0-2 KJT0-S KJT0-S (ex.) Reference dimensions after NPT thread installation. Note1) : max. diameter L L2 A in. hole dia <-2UNF> <NPT> 2.2-5

57 Inch-size One-touch ini Series KJ Union tee: KJT L Q (inch) 5 2 KJT01-00 KJT0-00 KJT Note1) : max. diameter in. hole dia... Different dia. tee: KJT in. (inch) 1 2 L1 L2 Q1 Q2 1 2 hole a b dia. 5 2 KJT KJT Note1) 1, 2: max. diameter 2..9 ale run tee: KJY <-2UNF> <NPT> (inch) (T) UNF NPT -2UNF -2UNF 1 1-2UNF 1 1 KJY01-2 KJY01-S KJY01-S KJY0-2 KJY0-S KJY0-S KJY0-2 KJY0-S KJY0-S (ex.) Reference dimensions after NPT thread installation. Note1) : max. diameter L L L A in. hole dia <-2UNF> K <NPT> D S T 2.2-

58 Series KJ Union Y : KJU (inch) L1 L2 P Q KJU01-00 KJU0-00 KJU Note1) : max. diameter in. hole dia Different diameter union Y : KJU (inch) 1 2 L1 a b 5 2 KJU KJU Note1) 1, 2: max. diameter L P. 9. Q in. hole dia Plug-in Y : KJU (inch) Fitting size ød (inch) KJU01-99 KJU0-99 KJU0-99 Note1) 1: max. diameter L P. 9. A in. hole dia Different diameter Plug-in Y : KJX (inch) Fitting size ød (inch) KJX01-0 KJX0-0 Note1) 1: max. diameter L 5. P. 9. A in. hole dia

59 Inch-size One-touch ini Series KJ Branch Y : KJU <-2UNF> (inch) (T) UNF NPT -2UNF -2UNF 1 1 KJU01-2 KJU01-S KJU01-S KJU0-2 KJU0-S KJU0-S KJU0-2 KJU0-S (ex.) UNF KJU0-S Reference dimensions after NPT thread installation. Note1) 1: max. diameter L P A in. hole dia <UNF-2> <NPT> <NPT> Plug-in reducer: KJR (inch) Fitting size ød (inch) KJR01-0 KJR KJR0-0 Note1) : max. diameter. 9. L 2.5 A in. hole dia Bulkhead union: KJE (inch) 5 2 KJE01-00 KJE0-00 KJE0-00 ounting in. (T) L (ex.) hole hole UNF dia K D S T 2.2-

60 Inch-size One-touch Fittings Series KQ2 Applicable Tubing Inch Size UNF, NPT KQ2: White body KQ : Black body Guide Collet Chuck Accepts nylon, soft nylon and polyurethane tubes. as large retaining force. Release button (Red) KQ2: Orange KQ : Red Low disconnecting force. When the fitting is removed from the tubing, the chuck and collet are released, thus preventing them from biting into the tube excessively. Packing Can be used for a wide range of pressures from a low vacuum up to a pressure of 1.0Pa. The use of a special profile ensures sealing and reduces resistance when the tube is inserted. PAT. UNF, NPT Inch-sizes ", ", ", ", ", ", " Body O ring Stud when piping in a confined spaces. The body and threaded portion can turn independently. Applicable Tubing material (inch) Nylon, Soft nylon, Polyurethane ø, ø 5 2, ø 1, ø, ø 5 1, ø, ø Specifications Color Series KQ2 KQ Body White Black Release button Orange Red Operating fluid Air, Water ax. operating pressure 1.0Pa Proof pressure.0pa Ambient and fluid temperature 5 to 0 C (Water: 0 to 0 C) ANSI/ASEB (NTP thread) portion JIS B02 2A, Class 2B (UNF thread) Nut JIS B 02 2A, Class 2B (UNF thread) Sealant ( portion) With sealant Note1) Applicable for general industry water. Consult SC if using for other kind of fluids. Surge pressure must be under the max. operating pressure. Component aterials Body Stud Chuck Guide Collet Release button Packing, O ring Gasket C0BD, PBT, PP C0BD ( portion) Stainless Steel (SUS0) Stainless Steel (SUS0), C0BD, PO PO PO NBR PVC 2.2-9

61 Inch-size One-touch Fittings Series KQ2 odel ale connector KQ2 P Used to pipe in the same direction from female threaded portion. ost common style. Extended male elbow KQ2W P.2.2- For when the elbow extends over a standard elbow for easier of connection/disconnection of tubing. Plug-in Y KQ2U P Used to branch tubing in the same direction from One-touch fittings. Straight union KQ2 P Used to connect tubes in the same direction. ale branch tee KQ2T P Used to branch line from female thread in both 90 directions. Branch Y KQ2U P Used to branch line in the same direction from female thread. ale elbow KQ2L P Used to pipe at right angle to female threaded portion. ost common style. Union tee KQ2T P Used to connect tubes in both 90 directions. Bulkhead union KQ2E P.2.2- Used for junction connection of two tubes for installation of a panel. Union elbow KQ2L P.2.2- Used to connect tubes at right angles. ale run tee KQ2Y P Used for a branch line in the same direction from female thread and in 90 directions. Bulkhead connector KQ2E P.2.2- Used for transit connection of a tube and a male screw for installation of a panel. Plug-in elbow KQ2L P.2.2- Used to change by 90 in a tube fetching direction from Onetouch fittings. Plug-in reducer KQ2R P Used to change size of One-touch fittings. Plug KQ2P, KQP P.2.2- Used to shut unused One-touch fittings. KQ2P (Orange) KQP (Orange) Reducer elbow KQ2L P.2.2- Used to change by 90 in tube fetching direction from Onetouch fittings and to size down. Union Y KQ2U P Used to connect tubes in the same direction. Symbol 2 Accessory Body White Black Color Release button Orange Red Symbol Description KQ2P, KQP Plug (Orange) KQ 2 05 One-touch fitting odel ale connector Straight union ale elbow Union elbow L Plug-in elbow Reducer elbow W Extended male elbow ale branch tee T Union tee Y ale run tee Union Y U Plug-in Y Branch Y R Plug-in reducer Bulkhead union E Bulkhead connector ow to Order With mark: With sealant style is available. Additional models are available. See p S Applicable tube diameter Port size 2-2UNF 5 NPT 1 NPT NPT NPT NPT 00 Same dia. tube 99 Same dia. rod Sealant Without sealant S Sealant 2.2- K D S T

62 Series KQ2 ale connector: KQ KQ <KQ205-2> <NPT> (inch) Straight union: KQ2 ale elbow: KQ2L 01-2 KQ2L <KQ2L05-2> <NPT> (inch) (inch) -2UNF UNF NPT -2UNF 1 1 UNF NPT -2UNF 1 1-2UNF -2UNF -2UNF 1 1-2UNF -2UNF KQ KQ20-00 KQ KQ20-00 KQ KQ KQ21-00 KQ201-2 KQ201-S KQ201-S KQ201-5S KQ20-2 KQ20-S KQ20-S KQ20-5S KQ205-2 KQ205-S KQ205-5S KQ20-2 KQ20-S KQ20-5S KQ20-S KQ209-S KQ209-5S KQ209-S KQ211-S KQ211-5S KQ211-S KQ211-S KQ21-5S KQ21-S KQ21-S KQ2L01-2 KQ2L01-S KQ2L01-S KQ2L01-5S KQ2L0-2 KQ2L0-S KQ2L0-S KQ2L0-5S KQ2L05-2 KQ2L05-S KQ2L05-5S KQ2L0-2 KQ2L0-S KQ2L0-5S KQ2L0-S KQ2L09-S KQ2L09-5S KQ2L09-S KQ2L11-S KQ2L11-5S KQ2L11-S KQ2L11-S KQ2L1-5S KQ2L1-S KQ2L1-S (ex.) L (ex.) L L A Reference dimensions after NPT thread installation. Note1) : max. diameter in. hole dia Note1) : max. diameter 11 1 L2 A in. hole dia Reference dimensions after NPT thread installation. Note1) 1: max. diameter in. hole dia KQ <KQ205-2> <NPT> 01-2 KQ2L <KQ2L05-2> <NPT>

63 Inch-size One-touch Fittings Series KQ2 Union elbow: KQ2L (inch) KQ2L01-00 KQ2L0-00 KQ2L05-00 KQ2L0-00 KQ2L09-00 KQ2L11-00 KQ2L L Q in. hole dia Note1) : max. diameter Plug-in elbow: KQ2L (inch) Fitting size ød (inch) KQ2L01-99 KQ2L0-99 KQ2L05-99 KQ2L0-99 KQ2L09-99 KQ2L11-99 KQ2L L L A in. hole dia Note1) 1: max. diameter 2 Reducer elbow: KQ2L (inch) Fitting size ød (inch) KQ2L01-0 KQ2L01-05 KQ2L0-05 KQ2L0-0 KQ2L05-0 KQ2L05-09 KQ2L0-09 KQ2L0-11 KQ2L09-11 KQ2L09-1 KQ2L L1 L2 A in. hole dia Note1) 1: max. diameter Extended male elbow: KQ2W (inch) NPT KQ2W01-S KQ2W01-5S KQ2W0-S KQ2W0-5S KQ2W05-S KQ2W05-5S KQ2W0-S KQ2W0-5S KQ2W0-S KQ2W09-S KQ2W09-5S KQ2W09-S KQ2W11-5S KQ2W11-S KQ2W11-S KQ2W1-5S KQ2W1-S KQ2W1-S (ex.) L L A in. hole dia Reference dimensions after NPT thread installation. Note1) 1: max. diameter K D S T 2.2-

64 Series KQ2 ale branch tee: KQ2T <-2UNF> <R(PT)> (inch) -2UNF UNF NPT -2UNF 1 1-2UNF KQ2T01-2 KQ2T01-S KQ2T01-S KQ2T01-5S KQ2T0-2 KQ2T0-S KQ2T0-S KQ2T0-5S KQ2T05-S KQ2T05-5S KQ2T0-2 KQ2T0-S KQ2T0-5S KQ2T0-S KQ2T09-S KQ2T09-5S KQ2T09-S KQ2T11-S KQ2T11-5S KQ2T11-S KQ2T11-S KQ2T1-5S KQ2T1-S KQ2T1-S (ex.) L L2 A in. hole dia Reference dimensions after NPT thread installation. Note1) 1: max. diameter <-2UNF> <R(PT)> Union tee: KQ2T (inch) KQ2T01-00 KQ2T0-00 KQ2T05-00 KQ2T0-00 KQ2T09-00 KQ2T11-00 KQ2T L Q in. hole dia Note1) 1: max. diameter ale run tee: KQ2Y NPT (ex.) (inch) 1 1 KQ2Y01-S KQ2Y01-S KQ2Y01-5S KQ2Y0-S KQ2Y0-S KQ2Y0-5S KQ2Y05-S KQ2Y05-5S KQ2Y0-S KQ2Y0-5S KQ2Y0-S KQ2Y09-S KQ2Y09-5S KQ2Y09-S KQ2Y11-5S KQ2Y11-S KQ2Y11-S KQ2Y1-5S KQ2Y1-S KQ2Y1-S L1 L2 A in. hole dia Reference dimensions after NPT thread installation. Note1) 1: max. diameter

65 Inch-size One-touch Fittings Series KQ2 Plug-in reducer: KQ2R Union Y : KQ2U (inch) Fitting size ød (inch) (inch) KQ2U01-00 KQ2U0-00 KQ2U05-00 KQ2U0-00 KQ2U09-00 KQ2U11-00 KQ2R01-0 KQ2R01-05 KQ2R01-0 KQ2R0-05 KQ2R0-0 KQ2R05-0 KQ2R05-09 KQ2R0-09 KQ2R0-11 KQ2R09-11 KQ2R09-1 KQ2R L L L P A in. hole dia Note1) : max. diameter Q in. hole dia..5. Note1) : max. diameter Plug-in Y : KQ2U (inch) Fitting size ød (inch) KQ2U01-99 KQ2U0-99 KQ2U05-99 KQ2U0-99 KQ2U L L P Q A in. hole dia Note1) : max. diameter Branch Y : KQ2U (inch) NPT KQ2U01-S KQ2U01-5S KQ2U0-S KQ2U0-5S KQ2U05-S KQ2U05-5S KQ2U0-S KQ2U0-5S KQ2U0-S KQ2U09-S KQ2U09-5S KQ2U09-S KQ2U11-5S KQ2U11-S KQ2U11-S KQ2U1-5S KQ2U1-S KQ2U1-S (ex.) L P Q A in. hole dia Reference dimensions after NPT thread installation. Note1) : max. diameter K D S T

66 Series KQ2 Bulkhead union: KQ2E (inch) UNF KQ2E KQ2E KQ2E KQ2E KQ2E KQ2E KQ2E (ex.) L ounting hole in. hole dia Bulkhead connector: KQ2E (inch) NPT KQ2E01-5 KQ2E0-5 KQ2E05- KQ2E0-5 KQ2E09- KQ2E11- KQ2E1- KQ2E1- UNF (ex.) (ex.) L L in. ounting hole dia. hole Plug: KQ2P, KQP Fitting size ød (inch) L A KQ2P-01 KQ2P-0 KQ2P-05 KQ2P-0 KQ2P-09 KQ2P-11 KQ2P Inch-size One-touch Fittings Additional odels Available Style odel Port (inch) Port (inch) Style odel size size ex. -2UNF Triple -2UNF socket NPT universal NPT head male KQ2S NPT male KQ2VT NPT NPT NPT connector NPT 1 elbow 2 NPT -2UNF Double NPT 5 NPT branch male KQ2K NPT 1 universal NPT KQ2ZD male NPT elbow NPT elbow NPT NPT Triple NPT -2UNF branch Universal universal KQ2ZT NPT NPT male NPT male KQ2V NPT elbow NPT elbow NPT NPT NPT Female NPT ex. -2UNF connector KQ2F NPT socket NPT NPT head universal KQ2VS NPT NPT male NPT Female NPT elbow NPT elbow KQ2LF NPT Double -2UNF NPT universal NPT 5 2 NPT male KQ2VD 1 Different 1 elbow NPT NPT dia. KQ2 5 1 Universal -2UNF NPT straight female KQ2VF elbow 2 NPT NPT 5 5 NPT Different 1 Branch -2UNF universal NPT 1 dia. KQ2T 5 1 NPT male KQ2Z 1 tee NPT elbow NPT Refer to p and 2.1- for more information on styles Style odel Different dia. KQ2U union "Y" Cross KQ2TW Bulkhead male KQ2LE elbow Different dia. KQ2X Plug-in "Y" Nipple Reducer nipple cap KQ2N KQ2N KQ2C Port size (inch)

67 Inch-size Rotary One-touch Fittings Series KS (Standard) Applicable Tubing Inch-size Slide bearing Smooth operation and longer life are provided from an oil containing slide bearing. Cassette (Red) The half union style is equipped with a tube rotation prevention mechanism. Rotary seal A special rotary seal minimizes friction while providing an excellent seal. older Standard nickel plated allows copper-free applications. Ball bearing A ball bearing ensures low-torque rotation. Stud s are coated with a Teflon T based sealant for quick assembly. Low-torque rotation style Rotary One-touch fittings Applicable to use for oscillating and rotating sections in robots. Brass parts are all electroless nickel plated. sealant is standard. ale connector ale elbow Applicable Tubing material Nylon, Soft nylon, Polyurethane ø 5 /2, ø 1 /, ø 5 /1, ø / Note1) Be careful about the max. operating pressure for Soft nylon and Polyurethane. Specifications Fluid ax. operating pressure ax. operating vacuum pressure Proof pressure Ambient and fluid temperature Air 1.0Pa 0kPa.0Pa 5 to 0 C (No freezing) ANSI/ASEB (NTP thread) JIS B02 2A, Class 2B (UNF thread) Rotating Torque/Allowable Number of Rotations Applicable tube ø 5 /2 ø 1 / ø 5 /1 Rotating torque Nm Allowable number of rotations (rpm) Note1) Value under pressure 0.5Pa Component aterials Principal element Body Stud, older, Guide Chuck, Retainer Collet, Release button, Snap ring O ring, Packing Rotary seal Slide bearing Scraper Ball bearing Gasket ø / Series KS PBT SUS0,C0BD (With electroless nickel plated) Stainless Steel (SUS0) Polyacetal NBR NBR Oil-containing polyacetal Bearing steel Stainless Steel (SUS0), NBR K D S T 2.2-

68 Series KS Series KS odel ale connector KS Connection thread -2 UNF NPT Applicable tube (inch) ø 5 2 " ø " ø 5 1 " ø " NPT ale elbow KSL NPT -2UNF NPT NPT NPT Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Caution Precautions qinimize the load shown below to protect the ball bearing. A flexible polyurethane tube is recommended

69 Inch-size Rotary One-touch Fittings Series KS ale connector: KS (Standard) <UNF> in. UNF hole area (mm 2 ) D1 D2 L A (inch) NPT (ex.) dia. Nylon Urethane -2 UNF KS KS0-S KS0-S KS0-5S KS09-S KS09-5S KS11-5S KS11-S 55.5 SKSINC, #1 to # Reference dimensions after NPT thread installation. <UNF> <NPT> <NPT> ale elbow: KSL (Standard) <UNF> <NPT> in. UNF D1 D2 L1 L2 (ex.) A area (mm hole 2 ) (inch) NPT dia. Nylon Urethane -2 UNF KSL KSL0-S KSL0-S KSL0-5S KSL09-S KSL09-5S KSL11-5S KSL11-S 5 SKSINC, #9 to #1 Reference dimensions after NPT thread installation. <UNF> <NPT> K D S T 2.2-2

70 Rotary One-touch Fittings Series KS/KX (Standard) (igh Speed) Slide bearing Smooth operation and longer life from an oil containing slide bearing. Rotary seal A special rotary seal minimizes friction while providing an excellent seal. older Standard nickel plated allows copper-free applications. Ball bearing A ball bearing ensures low torque rotation. Stud s are coated with a Teflon T based sealant for quick assembly. Series KS (Standard) Series KX(igh speed) Scraper Prevents chips from intruding into bearing parts. Rotary seal X ring shape minimizes friction while providing an excellent seal. Seal is fire and shock proof fluorine rubber. Proves against high friction heat in high speed rotation and longer life. Cassette The male connector is equipped with a tube rotation prevention mechanism. Series KS Blue Series KX White Ball bearing A ball bearing ensures low torque rotation. SUS0C improves corrosion resistance. Other parts specifications are same as those of Series KS. Low torque rotation style Rotary One-touch fittings Applicable to use for oscillating and rotating sections in robots. Brass parts are all electroless nickel plated. sealant is standard. Applicable Tubing material Specifications Nylon, Soft nylon, Polyurethane ø, ø, ø, ø, ø Note1) Be careful about the max. operating pressure for Soft nylon and Polyurethane. Operating fluid ax. operating pressure ax. operating vacuum pressure Proof pressure Ambient and fluid temperature Air 1.0Pa 0kPa.0Pa 5 to 0 C (No freezing) JIS B020, JIS B0209 Rotating Torque/Allowable Number of Rotations Applicable tube Rotating torque (Nm) Allowable number of rotations (rpm) Series KS Series KX Note1) Value under pressure 0.5Pa ø ø ø ø ø ale connector ale elbow Component aterials Principal element Series KS Series KX Body Stud, older, Guide Chuck, Retainer Collet, Release button, Snap ring PBT C0BD (electroless nickel plated), SUS0 Stainless steel (SUS0) Polyacetal O ring, Packing NBR Rotary seal NBR FP Slide bearing Scraper Ball bearing Oil-containing polyacetal Bearing steel NBR Stainless (SUS0C) Gasket Stainless steel (SUS0), NBR Note1) Retainer (C) of Series KX: C0BD (electroless nickel plated)

71 Rotary One-touch Fittings Series KS/KX Series KS/Series KX odel Connection thread ø Applicable tube ø ø ø ø ale connector KS KX 5 X 0. X 1.0 R(PT) R(PT) R(PT) R(PT) ale elbow KSL KXL 5 X 0. X 1.0 R(PT) R(PT) R(PT) R(PT) Precautions Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Caution qinimize the load shown below to protect the ball bearing. A flexible polyurethane tube is recommended. K D S T 2.1-2

72 Series KS/KX ale connector: KS (Standard) <5, > <R(PT)> Connection thread R(PT) 5 X 0. X X 0. X 1.0 SKS, #1 to # KS0-5 KS0- KS0-01S KS0-5 KS0- KS0-01S KS0-02S KS0-01S KS0-02S KS0-0S KS-02S KS-0S KS-0S KS-0S KS-0S (ex.) 1 2 D D2 L A in. hole area (mm 2 ) dia. Nylon Urethane Reference dimensions after R(PT) thread installation. <5, > <R(PT)> ale connector: KX (igh speed) <5, > <R(PT)> Connection thread R(PT) 5 X 0. X X 0. X 1.0 SKX, #1 to # KX0-5 KX0- KX0-01S KX0-5 KX0- KX0-01S KX0-02S KX0-01S KX0-02S KX0-0S KX-02S KX-0S KX-0S KX-0S KX-0S (ex.) 1 2 D D2 L A in. hole area (mm 2 ) dia. Nylon Urethane Reference dimensions after R(PT) thread installation. <5, > <R(PT)> 2.1-

73 Rotary One-touch Fittings Series KS/KX ale elbow: KSL (Standard) <5, > <R(PT)> Connection thread R(PT) 5 X 0. X X 0. X 1.0 KSL0-5 KSL0- KSL0-01S KSL0-5 KSL0- KSL0-01S KSL0-02S KSL0-01S KSL0-02S KSL0-0S KSL-02S KSL-0S KSL-0S KSL-0S KSL-0S (ex.) 1 2 D D2 1 2 L1 L2 A in. hole area (mm 2 ) dia. Nylon Urethane <5, > <R(PT)> SKS, #1 to #0 Reference dimensions after R(PT) thread installation. ale elbow: KXL (igh speed) <5, > <R(PT)> Connection thread R(PT) 5 X 0. X X 0. X 1.0 KXL0-5 KXL0- KXL0-01S KXL0-5 KXL0- KXL0-01S KXL0-02S KXL0-01S KXL0-02S KXL0-0S KXL-02S KXL-0S KXL-0S KXL-0S KXL-0S SKX, #1 to #0 (ex.) 1 2 D1 D2 L1 L2 A in. hole area (mm 2 ) dia. Nylon Urethane Reference dimensions after R(PT) thread installation. <5, > <R(PT)> K D S T 2.1-

74 Inch-size One-touch Fittings anifold Series K Applicable Tubing Inch-size Compact piping possible. anifold piping possible. any varieties ( styles) available. One-touch fittings-efficient operation possible. odel odel K11 K Port A One-touch fitting One-touch fitting Porting Port B One-touch fitting NPT thread Number of Port A,, Port B Port A size size ø ø ø ø5 1 ø ø NPT NPT Construction K11 K11 K Applicable Tubing material Specifications Nylon, Soft nylon, Polyurethane ø, ø, ø, ø, ø odel K11 K Fluid Air, Water ax. operating pressure 1.0Pa Proof pressure Ambient and fluid temperature.0pa 5 to 0 C (Water: 0 to 0 C) (No freezing) ANSI/ASEB (NTP thread) Note1) Applicable for general industry water. Consult SC if using for other kinds of fluid. Surge pressure must be under the max. operationg pressure. Component aterials odel K11 K Body PBT Stud C0BD Chuck Guide Collet, Release button Packing, O ring SUS0 SUS0, C0BD PO NBR K Port A: One-touch fitting Port B: One-touch fitting Port A: One-touch fitting Port B: NPT female thread

75 Inch-size One-touch Fittings anifold Series K K11 Applicable tube (inch) FA FB N L1 L2 K K K K K K L L L L P Q Q2 1 A B 1.5 Port B in. port size K Applicable tube F (inch) Thead NPT N L1 L2 T (ex.) K K K K K K L L L L P Q Q Port B in. port size Precautions for the use with One-touch fittings Caution Refer to Air Fittings & Tubing Precautions for the installation/removal of One-touch fittings and other precautions. K D S T 2.2-2

76 Inch-size Rectangular ulti-connector Series KD Connecting Tubing:, 20 ulti-connector is effective in saving labor for separate transportation of the panel and the machine and for exchanging units due to failure. Substantial reduction in mounting space In comparison with a model requiring many union joints for panels and partitions, this model needs only a small space. One-touch connection/ disconnection of connector ultiple pipes can be connected/disconnected in one-touch operation without connection error. Thus man-hours for connection/disconnection is cut down substantially. One-touch tube connection One-touch fittings substantially cut down man-hours for piping. KD20 KD Plug connector Socket connector Packing Usable from vacuum to 1Pa odel Number of connecting tubes 20 Plate O. D. Applicable Tubing material Specifications ø ø5 2 ø ø 5 1 ø ø 5 2 ø ø 5 1 Fluid ax. operating pressure ax. operating vacuum pressure Proof pressure Ambient and fluid temperature Screw for bracket E type snap ring Clamp bolt With One-touch fittings Inch size ø, ø 5 2, ø, ø5 1 Applicable to non-copper style (with electroless nickel plated) s of different sizes can be used simultaneously. Two styles, with and 20 connector tubes, are available. Panel mounting bracket (Standard) Operation on the panel front permits mounting. oles for mounting bolts are not necessary. (ountable panel thickness is 5mm maximum.) Socket case Plug case Irregular shape permits engagement in a proper position. Color of release button KD-01 KD-0 KD-0 KD-09 KD20-01 KD20-0 KD20-0 KD g 520g 520g 950g Red Nylon, Soft nylon, Polyurethane ø, ø 5 2, ø 5 1 ø, Air 1.0Pa 0kPa 1.5Pa 5 to 0 C (No freezing) 2.2-2

77 Inch-size Rectangular ulti-connector Series KD aterial Plug case, Socket case Plate, Bracket Body Chuck Plug connector Guide Socket connector Collet Release button Packing Clamp bolt, Screw for bracket, Cross recessed head machine screw E type snap ring No. of connecting tubes 20 ø ø 5 2 ø ø 5 1 ø ø 5 2 ø ø5 1 PO SPCC Plated PBT, C0BD Electroless nickel plated (ø 5 1 ) Stainless steel (SUS0) SUS0, C0BD Electroless nickel plated, PO (ø 5 1 ) Plug Socket KDP-01 KDS-01 KDP-0 KDS-0 KDP-0 KDS-0 KDP-09 KDS-09 KD20P-01 KD20S-01 KD20P-0 KD20S-0 KD20P-0 KD20S-0 KD20P-09 KD20S-09 PO NBR SWR, Nickel Plated Stainless steel (SUS0) Color of release button ixed Sizes of Plug Connectors and Socket Connectors The rectangular multi-connector permits connector exchange in any desired position, thus allowing use of different sizes of tubes. Red Caution ow to Use Separation Loosen the clamp bolt to separate the plug side from the socket side. Socket side Plug side Connection Put together the irregular faces for engagement and connect the plug case to the socket. After tightening the clamp bolt by hand, tighten it further with hexagon bar wrench (nominal width across flats:) Panel mounting qloosen () screws for bracket on the socket side using a Phillips screwdriver (JIS nominal No.2) until the bracket touches the stop ring. Connector Plug connector Socket connector (With packing) ø ø 5 2 ø ø 5 1 ø ø 5 2 ø ø5 1 KDP-01 KDP-0 KDP-0 KDP-09 KDS-01 KDS-0 KDS-0 KDS-09 Color of release button Red wshift the panel mounting bracket to the inside (ove the screw for bracket in the longitudinal direction of the slot) and put the connector in the panel mounting hole. (Panel mounting hole: See Dimensions.) qloosen the cross recessed head machine screw using a Phillips screwdriver to remove the plate from the case. wafter exchanging connectors in desired places, fix the plate with a Phillips screwdriver to the case. eafter shifting the bolt for bracket to the out side, tighten the bolt with a Phillips screwdriver to fix the socket case. K rloosen the screw for bracket until the bracket touches the stop ring and shift the bracket to the inside to remove the connector from the panel. D S T 2.2-2

78 Series KS Dimensions KD ( ): Dimensions for KD-09 KD20 ( ): Dimensions for KD20-09 KD SKD2, #1 to # KD20 SKD202, #1 to # Precautions for the use with One-touch fittings Caution Refer to Air Fittings & Tubing Precautions for the details of installation/removal of One-touch fittings and other precautions. ade to Order Contact SC for detailed specifications, dimensions and delivery. ixed tube sizes ixed tube size manifolds are available to meet your individual requirements. Consult your SC sales representative for availability

79 iniature Fittings/SUS1 Series S Possible to use in corrosive applications Stainless Steel aterial (SUS1) Compact piping space has a large retaining force. ose nipple assures easy installation and removal. Line up various styles Possible for special tubing in a same direction. Accepts many styles of plastic tubing ose nipple and hose elbow accepts nylon, soft nylon, and polyurethane tubing. ose nipple Barb Configuration for easy insertion into the tube olds the tube tightly Body Stainless steel: SUS1 Gasket Light clamping torque Tight seal Possible for combination use of nylon tube and polyurethane tube. Cap nut Certainly hold the tube by manual clamping Easy removing the tube by loosening Stainless steel: SUS1 Barb fitting Barb Configuration for easy insertion into the tube olds the tube tightly Body Stainless steel: SUS1 Gasket Light clamping torque. Sure seal. Specifications Applicable tube material Nylon Soft nylon Applicable tube dia. ø/ø ø/ø ø.1/ø2.1 ø/ø ø/ø Polyurethane ø.1/ø2 ø/ø, ø/ø ax. operating pressure 1.5Pa 1.0Pa 0.Pa Port size aterial Body Gasket 5 (JIS B0209 class 2) Stainless steel (SUS1) PVC, nylon /GF0% 2.-

80 iniature Fittings Series S odel odel S-5AU- S-5AU- S-5AU- S-5ALU- S-5ALU- S-5ALU- S-5- S-5- S-5L- S-5L- Style Barb fitting P.2.-2 Barb elbow P.2.-2 ose nipple P.2.-2 ose elbow Application For soft nylon tube For polyurethane tube For soft nylon and polyurethane tube For soft nylon tube For polyurethane tube For soft nylon and polyurethane tube Body rotates at 0 around the stud axis For nylon, soft nylon, and polyurethane tube For nylon, soft nylon, and polyurethane tube Body rotates at 0 around the stud axis /I.D. ø.1/ø2.1 X 5 ø.1/ø2 X 5 ø/ø X 5 ø/ø X 5 ø.1/ø2.1 X 5 ø.1/ø2 X 5 ø/ø X 5 ø/ø X 5 ø/ø X 5 ø/ø X 5 ø/ø X 5 ø/ø X 5 odel Style Application /I.D. S-5UL S-5UT S-5B S-5P S-5J S-5N S-5UN S-5ATU- S-5ATU- S-5ATU- Universal elbow P.2.-2 Universal tee P.2.-2 Bushing P.2.-2 Plug P.2.-2 Extention fitting P.2.-2 Nipple P.2.-2 Unilversal nipple P.2.-2 Barb tee for soft tubing Body rotates at 0 around the stud axis Body rotates at 0 around the stud axis To plug unused 5 port Solid piecemoves fitting up from work piece Fitting to work piece and fitting to fitting connection Body rotates at 0 around the stud axis For soft nylon tube For polyurethane tube For soft nylon and polyurethane tube Body rotates at 0 around the stud axis 5 female X 5 male 5 female X 5 female X 5 male For reducing Rc(PT) female to Rc(PT) 1 male 5 female X 5 female 5 male X 5 female 5 male X 5 male 5 male X 5 male PAT ø.1/ø2.1 X 5 ø.1/ø2 X 5 ø/ø X 5 ø/ø X 5-5G1 P.2.-2 Gasket P.2.-2 To seal 5 thread aterial: PVC -5G P.2.-2 Gasket () P.2.-2 S-5ALU- S-5L- S-5L- S-5ATU- only aterial: Nylon GF 0% K D S T 2.-

81 Series S Barb fitting for soft nylon: S-5AU-, -, - C S-5AU S-5AU S-5AU L area (mm 2 ) Barb elbow for soft nylon: S-5ALU-, -, - A C S-5ALU S-5ALU S-5ALU L area (mm 2 ) S-5ALU-, - S-5ALU- ose nipple: S-5-, - S-5- S-5- B 1. L E øf.5.5 area (mm 2 ) ose elbow: S-5L-, - S-5L- S-5L- A 1.5 B C E øf.5.5 L.. 1 N 5.5 area (mm 2 ) Universal elbow: S-5UL Universal tee: S-5UT area: 2.mm 2 :.5g area: 2.mm 2 :.5g 2.-2

82 iniature Fittings Series S Bushing: S-5B Plug: S-5P Extension fitting: S-5J area: mm 2 : 5.5g : 1.2g Nipple: S-5N A1 area:.0mm 2 :.g Barb tee for soft tubing: S-5ATU-, -, - A2 S-5ATU S-5ATU S-5ATU C S-5ATU-, - S-5ATU- Universal nipple: S-5UN area:.0mm 2 :.g Gasket: -5G1, -5G area (mm 2 ) Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Tightening of 5 thread Caution qtighten by hand, and give it an additional 1/ rotation with a wrench. (The additional rotation should be doubled to 1/2 when using the universal elbow, universal tee, etc. which have two gaskets.) If tightened too much, thread portion may be damaged and gasket may be deformed. This will cause air leakage. On the contrary, if tightening is not sufficient, thread may loosen causing air leakage. Caution Caution area:.0mm 2 : 1.g Precautions Use of tube with hose nipple qcut the tube perpendicularly to the tube axis to a little longer length than required length. (Use tube cutter TK-1, TK-2 or TK-.) wpass the tube through the cap nut. epush the tube until it comes to the end of the barb portion, or it may cause air leakage or hose releasing. rtighten the cap nut firmly by hand on the fitting. Use of tube with barb fitting qcut the tube perpendicularly to the tube axis to a little longer length than required length. (Use tube cutter TK-1, TK-2 or TK-.) wpush the tube in until it comes to the end of the barb portion, or it may cause air leakage or release hose. K D S T : 0.01g : 0.0g 2.-2

83 Polyurethane Tubing Series TU,TIUB For general air pressure tubing Orange color now becomes standard 0m roll available for all color types Burst Pressure Characteristics Curve Series Table : 20m roll : 0m roll size etric size (Series TU) Inch size (Series TIUB) odel TU025 TU00 TU005 TU5 TU0 TIUB01 TIUB05 TIUB0 TIUB11 TIUB1 I. D Black (B) White (W) Red (R) Blue (BU) Yellow (Y) Green (G) Clear (C) Orange (YR) Specifications Fluid ax. operating pressure Burst prssure in. bending radius Operating temperature aterial 5 2 " 5 1 " Air, Water 0.Pa at 20 C Refer to pressure characteristics curve to +0 C (Water: 0 to 0 C) (No freezing) Polyurethane Nominal size (inch) " 1 " " " " Precautions Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Caution qapplicable for general industry water. Consult SC if using for other kinds of fluids. Surge pressure must be under the max. operating pressure. If exceeding that value, fitting may damaged and tubing may burst. wthe value of the max. operating pressure is at a temperature of 20 C. Refer to the burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises which may burst the tubing. ethe values of the min. bending radius is at a temperature of 20 C. igher temperatures allows the tubing to bend more. ow to Order TU025 BU Indication of tube model Color indication Symbol Color B Black W White R Red BU Blue Y Yellow G Green C Clear YR Orange ade to Order q 0m roll for etric size (black, white, red, blue, yellow, green) and Inch size (black, white, red, blue, yellow, green) Suffix -X to the end of part number. Ex.) TIUB01Y-0- X Consult SC in case of ø1. 20 Length per roll Symbol Roll size 20 20m roll 0 0m roll w 20m roll for Inch size (except black and white) Suffix -X to the end of part number. Ex.) TIUB01Y-20- X e Longer roll length (black, white, red, blue, yellow, green) Suffix -X to the end of part number. Ex.) TU025B-500- X Available 0m for ø, 200m for ø, 500m for ø and ø. Contact SC for other lengths. K D S T 2.-

84 Nylon Tubing Series T,TIA For general air tubing Nylon tubing Burst Pressure Characteristics Curve Series Table etric size (Series T) size Inch size (Series TIA) odel T025 T00 T00 T05 T00 T5 T09 T11 TIA01 TIA05 TIA0 TIA11 TIA I. D Black (B) White (W) Red (R) Blue (BU) Yellow (Y) Green (G) : 20m roll : 0m roll Specifications Fluid ax. operating pressure Burst pressure in. bending radius Operating temp. aterial 5 2 " 5 1 " Air, Water 1.5Pa at 20 C Refer to burst pressure characteristics curve to +0 C (Water: 0 to 0 C) (No freezing) Nylon Nominal size (inch) " 1 " " " " Precautions Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Caution qapplicable for general industrial water. Consult SC if using for other kinds of fluid. Surge pressure must be under the max. operating pressure. If exceeding that value, fitting may be damaged and tubing may be burst. wthe value of the max. operating pressure is at a temperature of 20 C. Refer to the burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rise which may burst the tubing. ethe values of the min. bending radius is at a temperature of 20 C and variable rate % max. In case that operating temperature is higher than 20 C, variable rate may be over % even if bending radius is within the specified range. ow to Order T025 B Indication of tube model Color indication Symbol Color B Black W White R Red BU Blue Y Yellow G Green ade to Order 20 q 0m roll for etric size (black, white, red, blue, yellow, green) and Inch size (black, white, red, blue, yellow, green) Suffix -X to the end of part number. Ex.) T025R-0- X Consult SC in case of ø1. Length per roll Symbol Roll size 20 20m roll 0 0m roll (Black and white only) w 20m roll for Inch size (except black and white) Suffix -X to the end of part number. Ex.) TIA01BU-20- X e Longer roll length (black, white, red, blue, yellow, green) Suffix -X to the end of part number. Ex.) T025B-500- X Available 0m for ø, 200m for ø, 500m for ø and ø. Contact SC for other lengths. K D S T 2.-1

85 Soft Nylon Tubing Series TS,TISA For general air pressure Playable Burst Pressure Characteristics Curve Series Table : 20m roll : 0m roll size etric size (Series TS) Inch size (Series TISA) odel TS025 TS00 TS00 TS5 TS09 TS1 TISA01 TISA05 TISA0 TISA11 TISA I. D Black (B) White (W) Red (R) Blue (BU) Yellow (Y) Green (G) Specifications Fluid ax. operating pressure Burst prssure in. bending radius Operating temperature aterial 5 2 " 5 1 " Air 1.0Pa at 20 C Refer to pressure characteristics curve to +0 C (No freezing) Nylon Nominal size (inch) " 1 " " " " Precautions Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. Caution quse nylon or polyurethane tubing for general industry water. If using soft-nylon tubing, air leakage or tubing coming out caused by the contraction may occur. wthe value of the max. operating pressure is at a temperature of 20 C. Refer to the burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises which may burst the tubing. ethe value of the min. bending radius is at a temperature of 20 C and variable rate % max. In case that operating temperature is higher than 20 C, variable rate may be over % even if bending radius is within the specified range. ow to Order TS00 W Indication of tube model Color indication Symbol Color B Black W White R Red BU Blue Y Yellow G Green ade to Order 0 q 0m roll for etric size (black, white, red, blue, yellow, green) and Inch size (black, white, red, blue, yellow, green) Suffix -X to the end of part number. Ex.) TS00BU-0- X Consult SC in case of ø1. Length per roll Symbol Roll size 20 20m roll 0 0m roll (Black and white only) w 20m roll for Inch size (except black and white) Suffix -X to the end of part number. Ex.) TISA01BU-20- X e Longer roll length (black, white, red, blue, yellow, green) Suffix -X to the end of part number. Ex.) TS25B-500- X Available 0m for ø, 200m for ø, 500m for ø and ø. Contact SC for other lengths. 2.-2

86 Soft Polyurethane Tubing Series TUS Suitable for piping in confined spaces Extremely flexible Soft Polyurethane Tubing TUS related accessories lnner Sleeve Series TJ Reinforces soft polyurethane tubing. Insert an inner sleeve into soft polyurethane tubing when used with a One-touch fitting. Series Table odel I.D. Black (B) White (W) Red (R) Blue (BU) Yellow (Y) Green (G) Opaque (N) Yellow brown (YB) TUS025 TUS00 TUS005 5 : 20m roll TUS5.5 : 0m roll TUS0 odel TJ-025 TJ-00 TJ-005 TJ-5 TJ-0 Specifications aterial Wall thickness Be sure to read before handling. Refer to p.0-2 and 0-2 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.2.0- and 2.0- for more detailed precautions of every series. 2.- Applicable tube model TUS025 TUS00 TUS005 TUS5 TUS0 Length C200T (Nickel plated) 0.2mm Precautions Caution quse nylon or polyurethane tubing for general industry water to prevent the tubing from coming out or bursting due to possibility of surge pressure generation. wthe value of the max. operating pressure is at a temperature of 20 C. Refer to the burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rise which may burst the tubing. ethe value of the min. bending radius is at a temperature of 20 C. igher temperatures allows the tubing to bend more. ruse inner sleeve taking the removing force into consideration when used with Onetouch fittings. Specifications Fluid ax. operating pressure Burst pressure Applicable tube fitting in. bending radius (2) Operating temperature aterial drawing Without strenght N inner sleeve (Using One-touch fitting) With inner sleeve Air 0.Pa at 20 C Refer to burst pressure characteristics curve. One-touch fitting, Insert tube fitting, ose nipple () to +0 C (No freezing) Polyurethane Note1) Not clear but opaque due to material. Note2) in. bending radius is measured as shown in the figure below. Note) Always use inner sleeve (Series TJ) in safety circuit or critical area. ow to Order TUS5 B Indication of tube model Bend the tube into U-form at a temperature of 20 C. Fix one end and close loop gradually. easure 2R when the tube breaks or is crushed. 0 Burst Pressure Characteristics Curve Length per roll Symbol Roll size Color indication 20 20m roll Symbol Color 0 0m roll (Black, Blue only) B Black W White R Red BU Blue Y Yellow G Green N Opaque YB Yellow brown

87 Accessories/Tools ulti-tube older Series T Easy arrangement of tubing Easy loading and firm holding of tube Possible to separate options depending on number of connecting tubes Use of flame resistance resin (V-0) Applicable Tubing material odel T-0 T-0 T-0 T- T- Nylon, Soft nylon, Polyurethane ø, ø, ø, ø, ø No. of connecting tubes (AX.) Specifications Ambient temperature aterial Color Accessories 20 to 0 C Flame resistance polypropylene (UL-9 standard, V-0) Black For mounting Cross recessed head countersunk tapping screw (Black zinc chromate treatment) Size No. of (Nominal X Length) tubings T-0 2 X T-0 2. X T-0 T- X T- ulti-tube older/dimensions odel T-0 T-0 T-0 T- T- N (No. of holding parts) P L1.25 L2 W Caution qcut the multi-tube holder depending on number of tubes to be connected. <Cutting method> Cut the groove for separation with side cutters. W2 11 ow to Use W ounting screw Nominal X Length 2 X 2. X 2. X X X winstall the multi-tube holder to equip-ment by use of the phillips head recessed, countersunk tapping screw. elay the tube across the gripper and push on the tube. rfor removing the tubes, pull up the tubes from the gripper. K D S T -1

88 Accessories/Tools ulti-holder Series TA Can be used to secure the KE series exhaust valve with One-touch fitting One-touch fitting can also be secured. Union tee: KQT Elbow: KQL Straight: KQ Depending on the number of holders required, they can be separated as desired (align the cutter with the cutting groove and cut the holder) Specifications Ambient temperature ( C) aterial Color odel odel TA-0 TA-0 TA- TA- Number of tubes ulti-holder/dimensions 20 to 0 C Flame resistance polypropylene (UL-9 standard V-0) Black Applicable exhaust valve KEA0 KEB0 KEA0 KEB0 KEC-02 KEA- KEB- KEA- KEB- KEC-0 Applicable one touch fitting Union tee Union elbow Straight union KQT0-00 KQT0-00 KQT-00 KQT-00 KQL0-00 KQL0-00 KQL-00 KQL-00 KQ0-00 KQ0-00 KQ-00 KQ-00 odel P L W 1 2 Q TA-0 TA-0 TA- TA

89 Accessories/Tools Cutter Series TK Cutter: TK-1 Perpendicular cutting Reduced operating force Enclosure/safety lock contained material Note) Never cut metals such as electric wires. TK-1 Nylon, soft nylon, polyurethane, and other soft plastic tube 1mm or less 10g Cutter: TK-2 Possible to cut a tube up to 1mm. material Note) Never cut metals such as electric wires. TK-2 Nylon, soft nylon, polyurethane, and other soft plastic tube 1mm or less 10g K D S T -

90 Accessories/Tools Cutter Series TK Cutter: TK- (Useful type) Safety lock contained. Note) Never cut metals such as electric wires. material TK- Nylon, soft nylon, polyurethane, and other soft plastic tube mm or less 2g -

91 Accessories/Tools Releasing Tool Series TG For loading and unloading of tubes for One-touch fittings mounted in a narrow space or on manifolds. Easy one-hand operation Available for two sizes of applicable tubes. Easy exchange with one hand. size material TG-1 TG-2 etric size Inch size ø, ø ø ", ø " Nylon, Soft nylon, Polyurethane Color Blue Red g Caution Process qput the end of tool into the release button parallel to the tube. ow to Use Size change Push both sides at once to release. Reverse and fix at the same position as before. Applicable tube size is indicated on the back side. wafter inserting, grasp the handle tightly and insert the end of the tubing to the stroke end. Note) Insert firmly to guard against accidental tube release. eafter inserting end of tube, relax your grip on the tool. Returning force of spring releases the tube. K D S T -5

92 Uni One-touch Fittings New-stand male threads for piping that reduces the screw-in time by 1/ Uni thread ridge shape A gasket made of stainless sheet covered with laminated NBR on both sides is seated on the chamfer of a female thread for a perfect sealing construction irrespective of the difference in thread diameters due to the difference in the types of female threads, variation in tolerance, or difference in the size of chamfer. (It is applicable to any female thread with an ordinary chamfer.) Applicable tubing /etric size Style odel Port size ø ø ø ø ø ø1 Applicable tubing /Inch size Style odel Port (inch) size ale connector KQ ale connector KQ ale elbow KQL ale elbow KQL A ridge shape has been created as a Uni thread for common applications for Rc(PT), G(PF), NPT and NPTF The male thread for piping drastically cuts piping manhours Branch tee ale run tee Branch Y KQT KQY KQU Branch tee ale run tee Branch Y KQT KQY KQU Extended male elbow exagon socket head male connector KQW KQS Extended male KQW elbow Refer to the catalog No. CAT. E505 for the details. 5 ale elbow Universal male elbow KQK KQV -