Optical Fiber Photoelectric Sensor

Transcription

1 Supply voltage Output 12 to 24 VDC (Optical fiber series) 0 ma Optical Fiber Photoelectric Sensor Leading-edge Features and Long-distance Sensing in an Optical Fiber Photoelectric Sensor -T with Auto-tuning Function Automatic Sensitivity Adjustment -H11 High-sensitivity Model Senses Distances Twice as Far as those of -A and Performs Detailed Sensing Operations Using the Variable Hysteresis Function -A Standard Model A High-speed Response of 200 µs -F High-speed Model Pulse Lighting Mechanism Enables a High-speed Response of 20 µs -VG Mark Sensor Model Green Light Source Accurately Senses Subtle Differences in Color at a Speed of 200 s Ordering Information Model Number Legend: Classification T: Auto-tuning H: High-sensitivity A: General-purpose F: Shorter response time V: For mark sensor 2. Light Source None: Red (standard) G: Green 3. Outputs 1: NPN (without self-diagnosis) 2: NPN (with self-diagnosis) 4: PNP (without self-diagnosis) 5: PNP (with self-diagnosis) 4. Output Form 1: Cable Accessories (Order Separately) (Cannot be used with the -T.) 1

2 Application Item Manual Sensitivity Adjustment Knob Protective Cover Makes adjustment possible without screwdriver. Water-resistance lost when used (enclosure rating reduced to IP50). Model E39-G3 E39-G4 Appearance Replacement part for cover supplied with Amplifier Unit. Amplifier Units Item Auto-tuning High-sensitivity Model -T11 -T21 -H11 Appearance 32 Light source Red LED (660 nm) 12 Power supply voltage 12 to 24 VDC +%, ripple (p-p) % max. to 30 VDC +%, ripple (p-p) % max. Current consumption 50 ma max. 35 ma max. Response time 500 ms max. 1 m sec max. Control output 0 ma max. at 30 VDC, NPN open collector Timer function --- -delay timer (fixed to 40 ms), switch selectable Self-diagnosis alarm output ma max. at 30 VDC, open collector Variable hysteresis function --- 0% to 20% Tuning monitor function Indicator (red/green LED) and buzzer --- Remote tuning function/ --- When, short-circuit the --- Remote bank function blue and pink wires. (Short-circuit the blue and purple wires for remote bank selection.): Short-circuit voltage 3 V max., short-circuit current 5 ma min. When, open the blue and pink wires: 9 V min. (input voltage: 24 V max.), response time 0 ms max. when. Output method Light and Dark selector

3 Item General-purpose Shorter response time For mark sensing Model NPN -A11 -A21 -F21 -VG11 -VG21 Appearance PNP -A41 -A51 -F Light source Red (660 nm) Green (565 nm) Power supply voltage to 30 VDC ripple (p-p) % max. 12 to 24 VDC +% ripple (p-p) % max. Current consumption 35 ma max. 40 ma max. Response time 200 ms max. : 20 ms max. : 30 ms max. Control output 0 ma, 30 VDC max., Open collector Timer function --- -delay timer (0.01 to 0.1 s; adjustable), Switch selectable Self-diagnosis alarm output ma, 30 VDC max. Residual voltage: 1 VDC max. External diagnosis input Input voltage --- Light : NPN: 1.5 V max; short current: 0.2 ma max. PNP: ±1.5 V max.; short current: 0.2 ma max. Light : NPN: Open; Light : 3.5 V min. (max. input: 5 V) PNP: Open; ±3.5 VDC max. (max. input: 5 V) to 30 VDC ripple (p-p) % max. 200 ms max delay timer (0.01 to 0.1 s; adjustable), Switch selectable ma, 30 VDC max. Residual voltage: 1 VDC max. --- Light : 1.5 V max; short current: 0.2 ma max. Light : Open; 3.5 V min. (max. input: 5 V) Response delay 400 ms 200 ms 400 ms 3

4 Fiber Unit Through-beam (Separate) Sensors Model Appearance (standard object)* (T: -T ; H: -H11; A: -A ; F: -F ; V: -VG ) E32-T11L E32-T12L E32-T21L E32-T22L E32-TC200 E32-TC200B E32-TC200B4 E32-T22 E32-TC200E E32-TC200F E32-TC200F4 E32-TC200A E32-T11 E32-T21 M4 screw 3-mm dia. M3 screw 2-mm dia. M4 screw M4 screw 2-mm dia. M3 screw M3 screw M3 screw M4 screw M3 screw T: 500 mm (1,200 mm**) (1.4-mm dia. min.) H: 700 mm ( mm**) (1.4-mm dia. min.) A: 350 mm (1,000 mm**) (1.4-mm dia. min.) F: 150 mm (1.4-mm dia. min.) V: 40 mm (120 mm**) (1.4-mm dia. min.) T: 500 mm (1.4-mm dia. min.) H: 700 mm (1.4-mm dia. min.) A: 350 mm (1.4-mm dia. min.) F: 150 mm (1.4-mm dia. min.) V: 40 mm (1.4-mm dia. min.) T: 150 mm (0.9-mm dia. min.) H: 200 mm (0.9-mm dia. min.) A: 0 mm (0.9-mm dia. min.) F: 50 mm (0.9-mm dia. min.) V: mm (0.9-mm dia. min.) T: 150 mm (0.9-mm dia. min.) H: 200 mm (0.9-mm dia. min.) A: 0 mm (0.9-mm dia. min.) F: 50 mm (0.9-mm dia. min.) V: mm (0.9-mm dia. min.) *Standard object: opaque; **For the E39-F1; ***Not trimmable T: 270 mm ( mm**) (1-mm dia. min.) H: 400 mm (3,000 mm**) (1-mm dia. min.) A: 200 mm (1,500 mm**) (1-mm dia. min.) F: 80 mm (1-mm dia. min.) V: 28 mm (190 mm**) (1-mm dia. min.) T: 270 mm (1-mm dia. min.) H: 400 mm (1-mm dia. min.) A: 180 mm (1-mm dia. min.) F: 80 mm (1-mm dia. min.) V: 28 mm (1-mm dia. min.) T: 70 mm (0.5-mm dia. min.) H: 0 mm (0.5-mm dia. min.) A: 50 mm (0.5-mm dia. min.) F: 26 mm (0.5-mm dia. min.) V: 7 mm (0.5-mm dia. min.) T: 70 mm (0.5-mm dia. min.) H: 0 mm (0.5-mm dia. min.) A: 50 mm (0.5-mm dia. min.) F: 26 mm (0.5-mm dia. min.) V: 8 mm (0.5-mm dia. min.) T: 70 mm (0.5-mm dia. min.) H: 0 mm (0.5-mm dia. min.) A: 50 mm (0.5-mm dia. min.) F: 26 mm (0.5-mm dia. min.) V: 8 mm (0.5-mm dia. min.) T: 250 mm (1-mm dia. min.) H: 360 mm (1-mm dia. min.) A: 180 mm (1-mm dia. min.) F: 80 mm (1-mm dia. min.) V: 28 mm (1-mm dia. min.) T: 240 mm (1,300 mm**) (1-mm dia. min.) H: 360 mm (1-mm dia. min.) A: 180 mm (1,000 mm**) (1-mm dia. min.) F: 80 mm (1-mm dia. min.) V: mm (120 mm**) (1-mm dia. min.) T: 65 mm (0.5-mm dia. min.) H: 0 mm (0.5-mm dia. min.) A: 50 mm (0.5-mm dia. min.) F: 26 mm (0.5-mm dia. min.) V: 6 mm (0.5-mm dia. min.) Min. sensing object (opaque objects) T: 0.2-mm dia. H: 0.5-mm dia. A: 0.5-mm dia. F: 0.5-mm dia. V: 0.5-mm dia. T: 0.2-mm dia. H: 0.5-mm dia. A: 0.5-mm dia. F: 0.5-mm dia. V: 0.5-mm dia. 0.2-mm dia. 0.2-mm dia. 0.2-mm dia. 0.2-mm dia. 0.2-mm dia. 0.2-mm dia. 0.2-mm dia. T: 0.2-mm dia. H: 0.3-mm dia. A: 0.2-mm dia. F: 0.2-mm dia. V: 0.2-mm dia. T: 0.2-mm dia. H: 0.3-mm dia. A: 0.2-mm dia. F: 0.2-mm dia. V: 0.2-mm dia. 0.2-mm dia. Features Long distance Long distance Long distance with thin fiber Long distance with thin fiber General-purpose General-purpose General-purpose General-purpose General-purpose General-purpose Flexible (resists breaking) Flexible (resists breaking) 4

5 Model Appearance (standard object)* (T: -T ; H: -H11; A: -A ; F: -F ; V: -VG ) E32-TC200C E32-TC200D E32-TC200D4 E32-T14L E32-T24 E32-T14 E32-T17L E32-T12F E32-M21 E32-T51 E32-T61 M4 screw **** M4 screw **** 3-mm dia. 1-mm dia. M4 screw 5-mm dia. M3 screw **** M4 screw M4 screw **** T: 200 mm (800 mm**) (1-mm dia. min.) H: 300 mm (1,600 mm**) (1-mm dia. min.) A: 150 mm (800 mm**) (1-mm dia. min.) F: 60 mm (1-mm dia. min.) V: 18 mm (0 mm) (1-mm dia. min.) T: 200 mm (1-mm dia. min.) H: 300 mm (1-mm dia. min.) A: 150 mm (1-mm dia. min.) F: 60 mm (1-mm dia. min.) V: 18 mm (1-mm dia. min.) T: 130 mm (1-mm dia. min.) H: 240 mm (1-mm dia. min.) A: 120 mm (1-mm dia. min.) F: 30 mm (1-mm dia. min.) V: mm (1-mm dia. min.) T: 45 mm (0.5-mm dia. min.) H: 90 mm (0.5-mm dia. min.) A: 45 mm (0.5-mm dia. min.) F: 15 mm (0.5-mm dia. min.) V: 2 mm (0.5-mm dia. min.) T: 1,000 mm (4-mm dia. min.) H: 1,800 mm (4-mm dia. min.) A: 900 mm (4-mm dia. min.) F: 380 mm (4-mm dia. min.) V: 80 mm (4-mm dia. min.) T: 7,000 mm (-mm dia. min.) H: 14,000 mm (-mm dia. min.) A: 7,000 mm (-mm dia. min.) F: 3,000 mm (-mm dia. min.) V: 800 mm (-mm dia. min.) T: 1,000 mm (4-mm dia. min.) H: 1,600 mm (4-mm dia. min.) A: 800 mm (4-mm dia. min.) F: 300 mm (4-mm dia. min.) V: 70 mm (4-mm dia. min.) T: 200 mm (2-mm dia. min.) H: 300 mm (2-mm dia. min.) A: 150 mm (2-mm dia. min.) F: 65 mm (2-mm dia. min.) V: 20 mm (2-mm dia. min.) T: 300 mm (1.5-mm dia. min.) H: 400 mm (1.5-mm dia. min.) A: 200 mm (1.5-mm dia. min.) F: 80 mm (1.5-mm dia. min.) V: 20 mm (1.5-mm dia. min.) T: 180 mm ( mm**) (1.0-mm dia. min.) H: 300 mm (3,000 mm**) (1.0-mm dia. min.) A: 150 mm (1,500 mm**) (1.0-mm dia. min.) F: 60 mm (450 mm) (1.0-mm dia. min.) V: 18 mm (130 mm**) (1.0-mm dia. min.) Min. sensing object (opaque objects) 0.2-mm dia. 0.2-mm dia. T: 0.3-mm dia. H: 0.2-mm dia. A: 0.1-mm dia. F: 0.2-mm dia. V: 0.1-mm dia. T: 0.2-mm dia. H: 0.1-mm dia. A: 0.1-mm dia. F: 0.3-mm dia. V: 0.2-mm dia. T: 0.2-mm dia. H: 1-mm dia. A: 1-mm dia. F: 0.2-mm dia. V: 2-mm dia. T: 0.7-mm dia. H: 2.1-mm dia. A: 0.8-mm dia. F: 1.5-mm dia. V: 2.1-mm dia. T: 0.3-mm dia. H: 0.7-mm dia. A: 0.9-mm dia. F: 0.7-mm dia. V: 0.6-mm dia. T: 0.2-mm dia. H: 0.4-mm dia. A: 0.3-mm dia. F: 0.3-mm dia. V: 0.3-mm dia. T: 0.4-mm dia. H: 1.0-mm dia. A: 1.0-mm dia. F: 1.0-mm dia. V: 1.0-mm dia. T: 0.2-mm dia. H: 0.3-mm dia. A: 0.2-mm dia. F: 0.5-mm dia. V: 0.5-mm dia. Features Flexible spiral cord Flexible spiral cord Side-view; long distance Side-view; save space Side-view Long distance Teflon-covered*****; withstands chemicals and harsh environments 4-head; 4-point sensing Heat-resistant; resists 150 C Heat-resistant; resists 300 C *Standard object: opaque; **For the E39-F1.; ***s for slit applications are in the following table. ****Not trimmable *****Teflon is a registered trademark of the Dupont Company and the Mitsui Dupont Chemical Company for their fluoride resin. 5

6 E32-T16 with Slits Slit width 0.5-mm 1.0-mm Sensing method With 450 mm 800 mm -T Min. sensing object 0.2-mm dia. 0.3-mm dia. With 900 mm 1,200 mm -H11 Min. sensing object 0.2-mm dia. 0.4-mm dia. With 450 mm 600 mm -A Min. sensing object 0.25-mm dia mm dia. With 120 mm 250 mm -F Min. sensing object 0.25-mm dia mm dia. With 20 mm 60 mm -VG Min. sensing object 0.25-mm dia mm dia. Reflective Sensors Model Appearance (standard object) (T: -T ; H: -H11; A: -A ; F: -F ; V: -VG ) E32-D11L E32-D12 E32-D21L E32-D22L E32-DC200 E32-DC200B E32-DC200B4 E32-DC200E E32-DC200F E32-DC200F4 E32-D11 M6 screw 3 mm dia. M4 screw M6 screw M6 screw M3 screw M3 screw M6 screw 3 mm dia. White paper T: 150 mm (20 x 20 cm) H: 200 mm (20 x 20 cm) A: 0 mm ( x cm) F: 45 mm (5 x 5 cm) V: mm (2.5 x 2.5 cm) T: 80 mm ( x cm) H: 120 mm (20 x 20 cm) A: 60 mm ( x cm) F: 15 mm (2.5 x 2.5 cm) V: 2 mm (2.5 x 2.5 cm) T: 35 mm (5 x 5 cm) H: 50 mm (5 x 5 cm) A: 25 mm (2.5 x 2.5 cm) F: 11 mm (2.5 x 2.5 cm) V: 1 mm (2.5 x 2.5 cm) T: 35 mm (5 x 5 cm) H: 50 mm (5 x 5 cm) A: 25 mm (2.5 x 2.5 cm) F: 11 mm (2.5 x 2.5 cm) V: 1 mm (2.5 x 2.5 cm) T: 0 mm ( x cm) H: 150 mm (20 x 20 cm) A: 75 mm ( x cm) F: 33 mm (5 x 5 cm) V: mm (2.5 x 2.5 cm) T: 0 mm ( x cm) H: 150 mm (20 x 20 cm) A: 75 mm ( x cm) F: 33 mm (5 x 5 cm) V: mm (2.5 x 2.5 cm) T: 20 mm (2.5 x 2.5 cm) H: 36 mm (5 x 5 cm) A: 18 mm (2.5 x 2.5 cm) F: 8 mm (2.5 x 2.5 cm) V: 2 mm (2.5 x 2.5 cm) T: 20 mm (2.5 x 2.5 cm) H: 36 mm (5 x 5 cm) A: 18 mm (2.5 x 2.5 cm) F: 8 mm (2.5 x 2.5 cm) V: 2 mm (2.5 x 2.5 cm) T: 60 mm ( x cm) H: 90 mm ( x cm) A: 45 mm (5 x 5 cm) F 20 mm (2.5 x 2.5 cm) V: 7 mm (2.5 x 2.5 cm) Black paper T: 40 mm (20 x 20 cm) H: 60 mm (20 x 20 cm) A: 30 mm ( x cm) F: 8 mm (5 x 5 cm) V: --- T: 20 mm ( x cm) H: 32 mm (20 x 20 cm) A: 16 mm ( x cm) F: 3 mm (2.5 x 2.5 cm) V: --- T: 9 mm (5 x 5 cm) H: 14 mm (5 x 5 cm) A: 7 mm (2.5 x 2.5 cm) F: 2 mm (2.5 x 2.5 cm) V: --- T: 9 mm (5 x 5 cm) H: 14 mm (5 x 5 cm) A: 7 mm (2.5 x 2.5 cm) F: 2 mm (2.5 x 2.5 cm) V: --- T: 20 mm ( x cm) H: 30 mm (20 x 20 cm) A: 15 mm ( x cm) F: 5 mm (5 x 5 cm) V: --- T: 20 mm ( x cm) H: 30 mm (20 x 20 cm) A: 15 mm ( x cm) F: 5 mm (5 x 5 cm) V: --- T: 4.8 mm (2.5 x 2.5 cm) H: 7.2 mm (5 x 5 cm) A: 3.6 mm (2.5 x 2.5 cm) F: 1.5 mm (2.5 x 2.5 cm) V: --- T: 4.8 mm (2.5 x 2.5 cm) H: 7.2 mm (5 x 5 cm) A: 3.6 mm (2.5 x 2.5 cm) F: 1.5 mm (2.5 x 2.5 cm) V: --- T: 13 mm ( x cm) H: 20 mm ( x cm) A: mm (5 x 5 cm) F: 5 mm (2.5 x 2.5 cm) V: --- Sensing object Slit Min. sensing object (copper wire) T: mm dia. H: mm dia. A: mm dia. F: 0.2-mm dia. V: 3.0-mm dia. T: mm dia. H: mm dia. A: 0.04-mm dia. F: 2.4-mm dia. V: 1.6-mm dia. T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.26-mm dia. V: 1.0-mm dia. T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.26-mm dia. V: 1.0-mm dia. T: mm dia. H: mm dia. A: mm dia. F: mm dia. V: 0.2-mm dia. T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 1.0-mm dia. T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 1.0-mm dia. T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 1.0-mm dia. T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 0.5-mm dia. Features Long distance Long distance Long distance Long distance General-purpose General-purpose General-purpose General-purpose Flexible (resists breaking) 6

7 Model E32-D21 E32-DC200C E32-DC200D E32-DC200D4 E32-DC9G E32-DC9G4 Appearance M3 screw M6 screw M6 screw ** ** 1.2-mm dia. ** (standard object) (T: -T ; H: -H11; A: -A ; F: -F ; V: -VG ) White paper T: 8 mm (2.5 x 2.5 cm) H: 14 mm (2.5 x 2.5 cm) A: 7 mm (2.5 x 2.5 cm) F: 3 mm (2.5 x 2.5 cm) V: 1 mm (2.5 x 2.5 cm) T: 30 mm (5 x 5 cm) H: 44 mm (5 x 5 cm) A: 22 mm (2.5 x 2.5 cm) F: mm (2.5 x 2.5 cm) V: 2.5 mm (2.5 x 2.5 cm) T: 30 mm (5 x 5 cm) H: 44 mm (5 x 5 cm) A: 22 mm (2.5 x 2.5 cm) F: mm (2.5 x 2.5 cm) V: 2.5 mm (2.5 x 2.5 cm) T: 35 mm (5 x 5 cm) H: 60 mm ( x cm) A: 30 mm (5 x 5 cm) F: 9 mm (2.5 x 2.5 cm) V: 2.5 mm (2.5 x 2.5 cm) E32-D33 T: 6 mm (2.5 x 2.5 cm) 3-mm dia. 0.8-mm dia. H: mm (2.5 x 2.5 cm) A: 5 mm (2.5 x 2.5 cm) F: 1.8 mm (2.5 x 2.5 cm) V: --- E32-CC200 T: 0 mm ( x cm) H: 150 mm (20 x 20 cm) M6 screw A: 75 mm ( x cm) F: 33 mm (5 x 5 cm) V: mm (2.5 x 2.5 cm) E32-D32 T: 30 mm (2.5 x 2.5 cm) H: 40 mm (5 x 5 cm) 2-mm dia. A: 20 mm (2.5 x 2.5 cm) F: 9 mm (2.5 x 2.5 cm) V: 2.5 mm (2.5 x 2.5 cm) E32-D32L T: 60 mm ( x cm) H: 80 mm ( x cm) 3-mm dia. A: 40 mm (5 x 5 cm) F: 11 mm (2.5 x 2.5 cm) V: 4 mm (2.5 x 2.5 cm) E32-D14L 6-mm dia. T: 40 mm (5 x 5 cm) H: 40 mm (5 x 5 cm) A: 40 mm (5 x 5 cm) F: 12 mm (2.5 x 2.5 cm) V: 1.5 mm (2.5 x 2.5 cm) E32-D24 T: 15 mm (2.5 x 2.5 cm) 2-mm dia. H: 15 mm (2.5 x 2.5 cm) A: 15 mm (2.5 x 2.5 cm) F: 4 mm (2.5 x 2.5 cm) V: 1.6 mm (2.5 x 2.5 cm) E32-D12F T: 50 mm (5 x 5 cm) H: 50 mm (5 x 5 cm) 6-mm dia. A: 50 mm (5 x 5 cm) F: 20 mm (2.5 x 2.5 cm) V: 4 mm (2.5 x 2.5 cm) Black paper T: 1.6 mm (2.5 x 2.5 cm) H: 3 mm (2.5 x 2.5 cm) A: 1.5 mm (2.5 x 2.5 cm) F: --- V: --- T: 6 mm (5 x 5 cm) H: mm (5 x 5 cm) A: 4.5 mm (2.5 x 2.5 cm) F: --- V: --- T: 6 mm (5 x 5 cm) H: mm (5 x 5 cm) A: 4.5 mm (2.5 x 2.5 cm) F: --- V: --- T: 7 mm (5 x 5 cm) H: 12 mm ( x cm) A: 6 mm (5 x 5 cm) F: 1.5 mm (2.5 x 2.5 cm) V: --- T: 1.3 mm (2.5 x 2.5 cm) H: 2 mm (2.5 x 2.5 cm) A: --- F: --- V: --- T: 20 mm ( x cm) H: 30 mm (20 x 20 cm) A: 15 mm ( x cm) F: 6 mm (5 x 5 cm) V: 2 mm (2.5 x 2.5 cm) T: 5.3 mm (2.5 x 2.5 cm) H: 8 mm (5 x 5 cm) A: 4 mm (2.5 x 2.5 cm) F: 1.5 mm (2.5 x 2.5 cm) V: --- T: mm ( x cm) H: 16 mm ( x cm) A: 8 mm (5 x 5 cm) F: 4 mm (2.5 x 2.5 cm) V: --- T: 8 mm (5 x 5 cm) H: 8 mm (5 x 5 cm) A: 8 mm (5 x 5 cm) F: 2 mm (2.5 x 2.5 cm) V: --- T: 2.5 mm (2.5 x 2.5 cm) H: 2.5 mm (2.5 x 2.5 cm) A: 2.5 mm (2.5 x 2.5 cm) F: --- V: --- T: 15 mm (5 x 5 cm) H: 15 mm (5 x 5 cm) A: 15 mm (5 x 5 cm) F: 6 mm (2.5 x 2.5 cm) V: --- Min. sensing object (copper wire) T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 1.0-mm dia. T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 1.0-mm dia. T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 1.0-mm dia. T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 1.0-mm dia. T: mm dia. H: mm dia. A: mm dia. F: 0.03-mm dia. V: --- T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 0.5-mm dia. T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 0.5-mm dia. T: mm dia. H: mm dia. A: 0.04-mm dia. F: 1.1-mm dia. V: 1-mm dia. T: 0.03-mm dia. H: 0.03-mm dia. A: 0.03-mm dia. F: 0.5-mm dia. V: 1.0-mm dia. T: 0.03-mm dia. H: 0.03-mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 1.0-mm dia. T: 0.03-mm dia. H: 0.03-mm dia. A: 0.03-mm dia. F: 0.5-mm dia. V: 0.5-mm dia. *Standard object: opaque **Not trimmable ***Teflon is a registered trademark of the Dupont Company and the Mitsui Dupont Chemical Company for their fluoride resin. Features Flexible (resists breaking) Flexible spiral cord Flexible spiral cord Stainless steel sleeve Super-thin; detail sensing Coaxial; positioning accuracy General-purpose General-purpose Side-view; long distance Side-view; save space Teflon-covered***; withstands chemicals and harsh environments 7

8 E32-D51 E32-D61 E32-D73 E32-R21 /E39-R3 E32-R16 /E39-R1 E32-L25 Model Appearance (standard object) (T: -T ; H: -H11; A: -A ; F: -F ; V: -VG ) E32-L25A E32-L25L E32-L24L M6 screw M6 screw ** ** M4 screw 1.25-mm dia. M6 screw *Standard object: opaque **Not trimmable Reflector E39-R3 Reflector E39-R1 White paper T: 60 mm ( x cm) H: 120 mm (20 x 20 cm) A: 60 mm ( x cm) F: 26 mm (5 x 5 cm) V: 5 mm (2.5 x 2.5 cm) T: 45 mm (5 x 5 cm) H: 45 mm (5 x 5 cm) A: 45 mm (5 x 5 cm) F: 20 mm (2.5 x 2.5 cm) V: 5 mm (2.5 x 2.5 cm) T: 30 mm (5 x 5 cm) H: 30 mm (5 x 5 cm) A: 30 mm (5 x 5 cm) F: 17 mm (2.5 x 2.5 cm) V: 3 mm (2.5 x 2.5 cm) T: 25 to 250 mm (35-mm dia. min.) H: to 250 mm (35-mm dia. min.) A: to 250 mm (35-mm dia. min.) F: 20 to 230 mm (35-mm dia. min.) V: --- T: 150 to 1,500 mm (35-mm dia. min.) H: 150 to 1,500 mm (35-mm dia. min.) A: 150 to 1,500 mm (35-mm dia. min.) F: 50 to 700 mm (35-mm dia. min.) V: --- T: 3.3 mm (2.5 x 2.5 cm) H: 3.3 mm (2.5 x 2.5 cm) A: 3.3 mm (2.5 x 2.5 cm) F: 3.3 mm (2.5 x 2.5 cm) V: --- T: 3.3 mm (2.5 x 2.5 cm) H: 3.3 mm (2.5 x 2.5 cm) A: 3.3 mm (2.5 x 2.5 cm) F: 3.3 mm (2.5 x 2.5 cm) V: --- H: 7.2±1.8 mm (2.5 x 2.5 cm) A: 7.2±1.8 mm (2.5 x 2.5 cm) F: 7.2±1.0 mm (2.5 x 2.5 cm) H: 4±2 mm (2.5 x 2.5 cm) A: 4±2 mm (2.5 x 2.5 cm) F: 4±2 mm (2.5 x 2.5 cm) Black paper T: 12 mm ( x cm) H: 24 mm (20 x 20 cm) A: 12 mm ( x cm) F: 5 mm (5 x 5 cm) V: --- T: 9 mm (5 x 5 cm) H: 9 mm (5 x 5 cm) A: 9 mm (5 x 5 cm) F: 4 mm (2.5 x 2.5 cm) V: --- T: 6 mm (5 x 5 cm) H: 6 mm (5 x 5 cm) A: 6 mm (5 x 5 cm) F: 3 mm (2.5 x 2.5 cm) V: --- Min. sensing object (copper wire) T: 0.03-mm dia. H: 0.03-mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 1.0-mm dia. T: 0.03-mm dia. H: 0.03-mm dia. A: 0.03-mm dia. F: 0.03-mm dia. V: 1.0-mm dia. T: 0.03-mm dia. H: 0.03-mm dia. A: 0.03-mm dia. F: 0.2-mm dia. V: 1.0-mm dia. --- T: 0.6-mm dia. H: 0.3-mm dia. A: 0.3-mm dia. F: 0.5-mm dia. V: T: 1.9-mm dia. H: 0.6-mm dia. A: 0.6-mm dia. F: 0.6-mm dia. V: T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.5-mm dia. V: T: mm dia. H: mm dia. A: 0.03-mm dia. F: 0.5-mm dia. V: H: mm dia. A: mm dia. F: mm dia. --- H: mm dia. A: mm dia. F: mm dia. Features Heat-resistive; resists 150 C Heat-resistive; resists 300 C Heat-resistive; resists 400 C Transparent objects sensing Transparent objects sensing Limited reflective; senses wafers and small difference in height Limited reflective; senses wafers and small difference in height Limited reflective, long distance; senses wafers and small difference in height Limited reflective, long distance, side-view; senses wafers and small difference in height 8

9 Fine Through-beam Model Appearance (standard object)* Min. sensing object (opaque objects) E32-T22S E32-T24S 1.7 mm dia. 3.5 x 3 mm dia. H: 1,000 mm (1.7-mm dia. min.) T: 650 mm (1.7-mm dia. min.) H: 700 mm (1.7-mm dia. min.) T: 450 mm (1.7-mm dia. min.) H: 0.5-mm dia. T: 0.4-mm dia. H: 0.5-mm dia. T: 0.4-mm dia. Features General purpose Side-view E32-T84S H: 700 mm (1.7-mm dia. min.) H: 0.4-mm dia. Sensing the wafers in cassettes (Fine, long beam sensor resisting 200 C) *Use the E32-T22S and E32-T24S in combination with the -H11, -T11, or -T21 Amplifier for stable wafer sensing. Slot Sensors Model Appearance (standard object)* Min. sensing object (opaque objects) E32-G14 mm (slot width) (4-mm dia. min.) T: 0.7-mm dia. H: 1.0-mm dia. A: 0.5-mm dia. F: 0.6-mm dia. V: 0.6-mm dia. *Standard object: opaque Liquid Level Fiber Unit Liquid Contact Model Model Appearance Standard sensing object E32-D82F1 E32-D82F2 Pure water at a temperature of 25 C. Sensing object angle range Repeat frequency Features Slot through-beam; no optical axis adjustment required Applicable Amplifier Unit (see note) ± max. 0.5 mm max. -NT/NM -NV -H When using the E32-D82F1 or E82-D82F2 with the -A, cut the plastic fiber part to 0.5 m, otherwise the energy of the light received by the -A will be insufficient. Pipe Mounting Model Model Appearance Standard sensing object Repeat frequency Applicable Amplifier Unit E32-L25T Liquid (Non-transparent liquids may not be sensed) 1 mm max. -NT/NM -A/H 9

10 High-precision Screen Sensors Model Appearance Slit width (H: -H11; A: -A ; F: -F ; V: -VG ) E32-T16P Not used H: 600 mm A: 300 mm 0.5 mm wide H: 0 mm A: 50 mm 1.0 mm wide H: 200 mm A: 0 mm E32-T16 Not used H: 1,500 mm A: 750 mm F: 330 mm V: 150 mm 0.5 mm wide H: 900 mm A: 450 mm F: 120 mm V: 20 mm 1.0 mm wide H: 1,200 mm A: 600 mm F: 250 mm V: 60 mm Min. sensing object* (horizontal beam) H: 1.3-mm dia. (1.1-mm dia.) A: 2.0-mm dia. (0.9-mm dia.) H: 1.3-mm dia. (0.4-mm dia.) A: 2.0-mm dia. (0.7-mm dia.) H: 1.3-mm dia. (0.6-mm dia.) A: 2.0-mm dia. (0.8-mm dia.) H: 6.0-mm dia. A: 6.0-mm dia. F: 7.0-mm dia. V: 7.0 mm dia. H: 5.0-mm dia. A: 5.0-mm dia. F: 7.0-mm dia. V: 7.0-mm dia. H: 6.0-mm dia. A: 6.0-mm dia. F: 7.0-mm dia. V: 7.0-mm dia. * Values not in parentheses represent sensing objects within the 11-mm sensing area and values in parentheses represent sensing objects in the center of the E32-T16P sensing area. The diameters of sensing objects in the above table represent sensing object sizes, on condition that the objects are not moving. Sensing Direction Sensing object Specifications Amplifier Units Indicator Sensitivity adjuster Circuit protection Ambient temperature Ambient humidity Ambient illumination Insulation resistance Dielectric strength Enclosure rating Material Connection method Weight (with 2-m cord) Light indicator (red), Stability indicator (green) 8 turns with indicator (except -T ) Reverse polarity, Output short-circuit Operating: 25 C to 55 C (with no icing) Storage: 40 C to 70 C 35% to 85% (with no condensation) Sunlight:,000 x max.; Incandescent lamp: 3,000 x max. 20 MW min. (at 500 VDC) 1,000 VAC, 50/60 Hz for 1 min IEC IP66 (with protective cover in place) (see note) Case: Heat-resistive ABS; Cover: Polycarbonate Cord-drawing method Approx. 0 g The enclosure rating is IP50 without the protection cover.

11 Fiber Unit Through-beam (Separate) Sensors Model Ambient temperature Ambient humidity Permissible bending radius E32-T11L Operating: 40 C to 70 C E32-T12L (with no icing) i E32-T21L E32-T22L E32-TC200 Operating: 35% to 85% Material 25 mm min. Black polyethylene IEC IP67 E32-TC200B E32-TC200B4 E32-T22 E32-TC200E E32-TC200F E32-TC200F4 E32-TC200A E32-T11 4 mm min. Vinyl chloride E32-T21 E32-TC200C 25 mm min. Black polyethylene E32-TC200D E32-TC200D4 E32-T14L E32-T24 E32-T14 E32-T17L E32-T12F Operating: 30 C to 70 C (with no icing) E32-M21 Operating: 40 C to 70 C (with no icing) E32-T51 E32-T61 Operating: 40 C to 150 C* (with no icing) Operating: 40 C to 300 C (with no icing) *When used continuously between 40 C and 130 C. 40 mm min. Teflon-covered black polyethylene 25 mm min. Black polyethylene 35 mm min. Fluoride resin 25 mm min. SUS Enclosure rating 11

12 Reflective Sensors Model Differential travel Ambient temperature E32-D11L 20% of max. of Operating: 40 C sensing distance to 70 C (with ihno E32-D12 (Adjustable in a icing) E32-D21L range of 0% to E32-D22L 20% when the -H11 is used.) E32-DC200 Ambient humidity Permissible bending radius Material Operating: 25 mm min. Black 35% to 85% polyethylene l E32-DC200B E32-DC200B4 E32-DC200E E32-DC200F E32-DC200F4 E32-D11 4 mm min. Vinyl chloride E32-D21 E32-DC200C 25 mm min. Black E32-DC200D polyethylene l E32-DC200D4 E32-DC9G E32-DC9G4 E32-D33 E32-CC200 E32-D32 E32-D32L E32-D14L E32-D24 E32-D12F E32-D51 E32-D61 E32-D73 E32-R21 E39-R3 E32-R16 E39-R1 E32-L25 E32-L25A E32-L25L*** E32-L24L*** Operating: 30 C to 70 C (with no icing) Operating: 40 C to 150 C (with no icing)** Operating: 40 C to 300 C (with no icing) Operating: 40 C to 400 C (with no icing) Operating: 40 C to 70 C (with no icing) Operating: 25 C to 55 C (with no icing) Operating: 40 C to 70 C (with no icing) Operating: 40 C to 5 C (with no icing) 40 mm min. Teflon-covered black polyethylene* 35 mm min. Fluoride resin 25 mm min. SUS mm min. (average at % decrease of sensing distance) Black polyethylene Reinforced polyethylene *Teflon is a registered trademark of the Dupont Company and the Mitsui Dupont Chemical Company for their fluoride resin. **When used continuously between 40 C and 130 C. ***Beam size: 2 mm dia. Enclosure rating IEC IP67 IEC IP66 IEC IP50 12

13 Fine Through-beam Sensors Model Beam size Differencial travel E32-T22S E32-T24S E32-T84S 13 mm dia. (at a distance of 200 mm) *Average at 30% of sensing distance Slot Sensors Horizontal positioning accuracy Ambient temperature Operating: 40 C to70 C (with no icing) Operating: 40 C to 200 C (with no icing) Ambient humidity Model Ambient temperature Ambient humidity Permissible bending radius E32-G14 Operating: 40 C to 70 C (with no icing) Liquid Contact Model Model Differencial travel Ambient temperature E32-D82F1 E32-D82F2 3.0 mm max. Teflon part within 1.5 m of fiber tip: 40 C to 200 C (with no icing) Parts other than above: 40 C to 85 C (with no icing) Operating: 35% to 85% Ambient humidity Operating: 35% to 85% Permissible Material bending radius* mm min. Reinforced laminated vinyl chloride Operating: 35% to 85% laminated 25 mm min. SUS Material 25 mm min. Black polyethylene IEC IP67 Ambient pressure 50 kpa ( 0.49 kgf/cm 2 ) to 500 kpa (4.9 kgf/cm 2 ) Permissible bending radius* (average at % of sensing distance) 40 mm min. (plastic fiber: 25 mm min.) Bending-prohibited part: E32-D82F1: Within 150 mm of fiber tip E32-D82F2: Within 350 mm of fiber tip Material Sensing head: Teflon* (PFA) Fiber sheath: Black polyethylene y Connector: Nickel-coated brass Enclosure rating IEC IP67 Enclosure rating Enclosure rating IEC IP68** *The teflon part located cm underwater must not generate air bubbles when air is injected into the teflon part with a pressure of 98 kpa (1 kgf/cm 2 ). **Teflon is a registered trademark of the Dupont Company and the Mitsui Dupont Chemical Company for their fluoride resin. Pipe Mounting Model Model Suitable pipe Pipe material Ambient temperature E32-L25T Transparent pipes with an outer diameter of 8 to mm and an inner diameter of 6 to 8 mm High-precision Screen Sensors FEP transparent pipes or equivalent Operating: 40 C to 70 C (with no icing) Ambient humidity Operating: 35% to 85% Permissible bending radius Material mm min. Sensing head: Polycarbonate Fiber: Polyethylenecovered plastic Enclosure rating IEC IP50 Model Ambient temperature Ambient humidity Permissible bending radius E32-T16P Operating: 40 C to 70 C (with no icing) Operating: 35% to 85% R mm min. Material Sensing head: Heat-resistive ABS Fiber sheath: Vinyl chloride E32-T16 25 mm min. Sensing head: Heat-resistive ABS Sensing surface: PMMA Fiber sheath: Black polyethylene Enclosure rating IEC IP50 IEC IP67 13

14 Attachments Name Small Spot Lens Unit Long Distance Lens Unit Applications Sensing over 0.5-mm-dia. spots Model E39-F3A E39-F1 Appearance Reflective Through-beam (separate) Increasing sensing distance Applicable fibers E32-D32 E32-T11L E32-TC200 E32-T11 E32-TC200C E32-T61 With 20 mm 1,200 mm mm 1,300 mm 800 mm -T Standard object White paper 2.5 x 2.5 cm Opaque objects: 4-mm dia. min. With 20 mm mm 3,000 mm mm 1,600 mm -H11 Standard object White paper 2.5 x 2.5 cm Opaque objects: 4-mm dia. min. With 20 mm 1,000 mm 1,500 mm 1,000 mm 800 mm -A Standard object White paper 2.5 x 2.5 cm Opaque objects: 4-mm dia. min. With 16 mm 550 mm 670 mm* 400 mm 350 mm -F Standard object White paper 2.5 x 2.5 cm Opaque objects: 4-mm dia. min. With mm 190 mm** 120 mm 0 mm -VG Standard object --- Opaque objects: 4-mm dia. min. Directivity to 40 Differential travel 20% of sensing distance --- Ambient temperature Operating: 40 C to 70 C Material Shaft Aluminum Brass Lens *E32-T6: 450 mm. **E32-T6: 130 mm. Name Base --- Reflector --- Optical glass Operating: 40 C to 200 C (Do not exceed the operating temperature of the fiber.) Side-view Unit Applications Changing the sensing direction at 90 Model E39-F2 Appearance Through-beam (separate) Applicable fibers E32-T11L E32-TC200 E32-T61/11 E32-TC200C With 250 mm 250 mm 200 mm 0 mm -T Standard object Opaque objects: 3-mm dia. min. With 400 mm 500 mm 400 mm 200 mm -H11 Standard object Opaque objects: 3-mm dia. min. With 200 mm 250 mm 200 mm 0 mm -A Standard object Opaque objects: 3-mm dia. min. With 60 mm 0 mm 60 mm 30 mm -F Standard object Opaque objects: 3-mm dia. min. With mm 19 mm mm 6 mm -VG Standard object Opaque objects: 4-mm dia. min. Directivity 20 to 60 Differential travel --- Ambient temperature Material Shaft Brass Lens Base --- Reflector --- Opaque objects: 3-mm dia. min. Operating: 40 C to 200 C (Do not exceed the operating temperature of the fiber.) Optical glass 14

15 Name Applications Model Appearance E39-F3 Lens-equipped Reflective Unit Converting through-beam sensors to reflective sensors Reflective Applicable fibers E32-T11L E32-TC200 E32-T61 With White paper 55 to 150* mm (20 x 20 cm) 85 to 0 mm (20 x 20* cm) -T (standard object) Black paper to 17*mm (20 x 20 cm) 16 to 18*mm (20 x 20 cm) With White paper to 300 mm (20 x 20 cm) 35 to 180 mm (20 x 20 cm) -H11 (standard object) Black paper to 120 mm (20 x 20 cm) 5 to 80 mm (20 x 20 cm) With White paper to 150 mm (20 x 20 cm) 35 to 90 mm ( x cm) -A (standard object) Black paper to 60 mm ( x cm) 5 to 40 mm ( x cm) With White paper to 65 mm ( x cm) 20 to 40 mm (5 x 5 cm) 20 to 35 mm (5 x 5 cm) -F (standard object) Black paper --- to 20 mm (5 x 5 cm) --- With White paper --- to 15 mm (2.5 x 2.5 cm) --- -VG (standard object) Black paper --- Directivity --- Differential travel Ambient temperature Material Shaft Brass Lens Base Reflector % of sensing distance Operating: 40 C to 200 C (Do not exceed the operating temperature of the fiber.) Optical glass Aluminum *These values are possible when the angle of the E39-F3 is smallest (parallel). 15

16 Name Lens-equipped Reflective Unit Side-view Reflective Unit Applications Converting through-beam sensors to reflective sensors Model E39-F3 E39-F5 Appearance Reflective Converting through-beam to reflective sensor Reflective Applicable fibers E32-T11 E32-TC200C E32-TC200A With (standard object) White paper 90 to 0* mm (20 x 20 cm) 85 to 0* mm (20 x 20 cm) 5 to 30* mm ( x cm) -T Black paper to 9* mm ( x cm) With White paper 35 to 180 mm (20 x 20 cm) 60 mm ( x cm) -H11 (standard object) Black paper 5 to 70 mm (20 x 20 cm) to 60 mm (20 x 20 cm) 5 to 20 mm ( x cm) With White paper 35 to 90 mm ( x cm) 30 mm (5 x 5 cm) -A (standard object) Black paper 5 to 35 mm ( x cm) to 30 mm ( x cm) 5 to mm (5 x 5 cm) With White paper 20 to 40 mm (5 x 5 cm) 20 to 35 mm (5 x 5 cm) 13 mm (2.5 x 2.5 cm) -F (standard object) Black paper With White paper VG (standard object) Black paper --- Directivity --- Differential travel Ambient temperature 20% of sensing distance Operating: 40 C to 200 C (Do not exceed the operating temperature of the fiber.) Material Shaft Brass --- Lens Optical glass --- Base Aluminum Brass Reflector --- Stainless *These values are possible when the angle of the E39-F3 is smallest (parallel). Operating: 40 C to 70 C Beam Spot Characteristics E39-F3A Focal length d (mm) Fiber E32-D32 d : Insertion distance d: Focal length 0.5 O: Spot diameter (mm) Insertion distance (mm) 16

17 Spiral Tubes Model E39-F32A5 E39-F32A E39-F32B5 E39-F32B E39-F32C5 E39-F32C E39-F32D5 E39-F32D Appearance L End cap Tube Head connector Length (L) 500 mm 1,000 mm 500 mm 1,000 mm 500 mm 1,000 mm 500 mm 1,000 mm Applicable fiber E32-DC200E E32-DC200F(4) E32-D21 E32-TC200E E32-TC200F(4) E32-T21 E32-T21L E32-TC200 E32-TC200B(4) E32-T11 E32-T51 E32-T11L Ambient temperature Operating: 40 C to 150 C (Do not exceed the operating temperature of the fiber) Ambient humidity Operating: 35% to 85% Permissible bending R: 30 mm min. radius Tensile strength Between head connector and end cap with tube: 15 kgf $ cm max. (1.5 N $ m) Tube: 20 kgf $ cm max. (2 N $ m) Compression load Tube: 3 kg max. (29.4 N) E32-DC200 E32-DC200B(4) E32-CC200 E32-D11 E32-D51 E32-D11L Accessories Name Fiber Cutter Fine-fiber Attachment Fiber Connector Sleeve Bender Model E39-F4 E39-F9 E39-F E39-F11 Appearance Features Applicable fiber Used to cut fibers to desired lengths All models equipped with trimmable fibers Used when inserting fine fibers into the amp E32-DC200E, -TC200E E32-DC200F(4), -TC200F(4) E32-D21, -D21L, -D22L E32-T21, -T21L, -T22L E32-D32, -T22 E32-D24. -T24 E32-D33 E32-R21 Used to connect fibers when broken E32-DC200, -TC200 E32-DC200B(4), -TC200B(4) E32-TC200A E32-T14, -G14 E32-D11L, -T11L, -T12L E32-D14L, -T14L E32-T17L Used to bend fiber sleeves E32-TC200B(4) E32-TC200D(4) E32-DC200F(4), -TC200F(4) E32-DC9G(4) 17

18 Engineering Data Excess Gain Ratio -T E32-TC200 E32-T11L E32-T11L + E39-F1 (mm) (mm) (m) E32-T11L + E39-F2 E32-T11L + E39-F3 (When the angle of the E39-F3 is at its minimum (parallel).) E32-T21L Sensing object Sensing distance (mm) (mm) (mm) E32-T14L E32-T17L E32-T16 (mm) (m) (m) 18

19 E32-DC200 E32-D11L E32-D21L Sensing object Sensing object Sensing object (mm) (mm) (mm) -H11 E32-TC200 E32-TC200 + E39-F1 E32-T11L (mm) (m) (mm) E32-T11L + E39-F1 E32-T11L + E39-F2 E32-T11L + E39-F3 Sensing object (m) (mm) (mm) 19

20 E32-T21L E32-T14L E32-T17L (mm) (mm) (m) E32-T16 E32-T22S E32-T24S (m) (mm) (mm) E32-DC200 E32-D11L E32-D21L Sensing object Sensing object (mm) (mm) (mm) 20

21 E32-T84S (mm) -A /-F /-VG E32-T11L, E32-T12L E32-T11L + E39-F1 E32-T11L + E39-F2 -F -A -F -A -F -A -VG Operating level -VG Operating level -VG Operating level (mm) (cm) E32-T11L + E39-F3 E32-T21L, E32-T22L E32-T14L (mm) Sensing object -F -A -F -A -F -A Operating level -VG Operating level -VG Operating level (mm) (mm) (mm) 21

22 E32-T17L E32-T12F E32-D11L -F -A -F -A -F -A Sensing object -VG Operating level -VG Operating level -VG Operating level (m) (cm) (mm) E32-D21L, E32-D22L E32-D14L E32-D12F -F Sensing object -A -F -A Sensing object -F -A Sensing object -VG Operating level -VG Operating level -VG Operating level (mm) (mm) (mm) Operating Range -T E32-DC200 E32-D11L X Y X Y E32-D21L X Y 22

23 -H11 E32-T11L + E39-F3 E32-DC200 E32-D11L Sensing object Sensing object Sensing object E32-D12 E32-D21L E32-DC200E Sensing object Sensing object Sensing object E32-D21 E32-D11 E32-CC200 Sensing object Sensing object Sensing object E32-D32 E32-D32L E32-D33 E32-D51 E32-L25L E32-T84S Sensing object Operating position Y X Sensing object Sensing object X 23

24 -A /-F /-VG E32-T11L + E39-F3 E32-DC200 E32-D11L -F -A -F -A -VG -F -A Sensing object Sensing object Sensing object With -A: Adjust the angle of E39-F3 so that the sensor can sense an object at a distance of 90 mm. (For -F: 50 mm) E32-D12 E32-D21L + E32-D22L E32-DC200E -VG Amplifier -F Amplifier -A Amplifier -F -A -A Sensing object Sensing object Sensing object E32-D21 E32-D11 E32-D33 -VG -F -A -A -A Sensing object Sensing object E32-CC200 E32-D32L E32-D14L -F -A -VG Amplifier -F Amplifier -A Amplifier -VG -F -A Sensing object 24

25 E32-D24 E32-D12F E32-D51 -F -A -VG -F -A Set distance X (mm) -F -A Sensing object Sensing object E32-D61 E32-D73 E32-R16 -F -A Sensing object -F -A Sensing object -A Sensing object E32-L25L Operating position Y Sensing object Sensing object X X 25

26 Parallel Operating Range (Typical) -T E32-TC200 E32-T11L Parallel operating range Y (mm) E32-T11L +E39-F1 Parallel operating range Y (cm) E32-T21L Parallel operating range Y (mm) X Y X Y X (m) X Y Set distance Parallel operating range Y (mm) Parallel operating range Y (mm) Parallel operating range Y (mm) E32-T11L + E39-F2 E32-T14L X Y X Y Set distance X Y E32-T17L E32-T12F Parallel operating range Y (cm) X Y X (m) Parallel operating range Y (cm) X Y Set distance X (m) 26

27 -H11 E32-TC200 E32-TC200 + E39-F2 E32-T11L E32-T11L + E39-F1 E32-T11L + E39-F2 E32-T21L E32-T21L E32-T22 E32-T11 Set distance E32-T21 E32-T14L E32-T24 E32-T14 E32-T17L E32-T12F 27

28 E32-M21 E32-T51 E32-T61 Set distance X (mm) E32-T22S E32-T24S -A /-F /-VG E32-TC200 E32-TC200 + E39-F2 E32-T11L/-T12L -VG -F -A -A -VG -F -A E32-T11L + E39-F1 E32-T11L + E39-F2 E32-T21L/-T22L -VG -F -A Set distance -VG -F -A -VG -F -A 28

29 E32-TC200E E32-T11 E32-T21 -VG -A -VG -A -A -F Set distance X (mm) -F -F E32-T14L E32-T24 E32-T14 -VG -F -A -VG -A -F -A E32-T17L E32-T12F E32-M21 -A -A -A -VG -F -VG -F -F21 Set distance E32-T51 E32-T61 E32-T61 + E39-F1 -A -A -A -F E32-T22S E32-T24S -A -VG -F -A -VG -F 29

30 Number of Turns of Sensitivity Adjuster and Sensing Distance (Typical) -H/E32-D11L Sensing Object: White Paper of 5 x 5 cm -A, -F/E32-D11L Sensing Object: White Paper of x cm with -A and 5 x 5 cm with -F (mm) (mm) -A -F Color Sensing (Typical) Green Light Source -VG /E32-D11L The following graph shows the relationship between colors and the number of turns of the sensitivity adjustor when the E32-D11L is in operation with the sensing distance adjusted to 5 mm. Munsell chroma (MC) White CM484 Sensitivity adjuster Sensitivity adjuster Yellow CM124 Amber CM 78 Yellow green CM157 Orange CM 85 Aqua CM263 Red CM 6 Purple CM379 Magenta CM431 Blue CM336 Green CM241 Black CM489 5 mm Color paper (2.5 x 2.5 cm) Number of turns 30

31 Nomenclature -T -H11 Stable Operation Indicator (Green Indicator) Tuning Indicator (Two Colors: red/green indicator) Tuning Button Light Reception Indicator (Red Indicator) Stable Operation Indicator (Green Indicator) Sensitivity Indicator The position of the indicator can be checked. 8-turn Sensitivity Adjuster Light Reception Indicator (Red Indicator) Operation Mode Selector L-: Output transistor is when light is received. D-: Output transistor is when light is not received. Mode Setting Selector Timer Switch : Timer function is. : Timer function is. Light Reception Monitoring Terminal (see note) Monitoring is used with the E39-VX Beam Checker Mode Selector SET: The light source flashes. Set to this mode to adjust the light axis. L-: Output transistor is when light is received. D-: Output transistor is when light is not received. Hysteresis Adjuster Timer Switch : Timer function is. : Timer function is. Light Reception Monitoring Terminal Monitoring is used with the E39-VX Beam Checker The light reception monitoring terminal is not available with the -T11. -A11/-A41 -VG11 -A21/-A51 -F21/-F51 -VG21 Stable Operation Indicator (Green Indicator) 8-turn Sensitivity Adjuster Light Reception Indicator (Red Indicator) Sensitivity Indicator Sensitivity adjustment can be checked visually. Stable Operation Indicator (Green Indicator) Sensitivity Indicator 8-turn Sensitivity Adjuster Light Reception Indicator (Red Indicator) Timer Adjuster Mode Selector SET: The light source flashes. Set to this mode to adjust the light axis. L-: Output transistor is when light is received. D-: Output transistor is when light is not received. Light Reception Monitoring Terminal Monitoring is used with the E39-VX Beam Checker Set the mode selector to L- or D- after the light axis is adjusted. Mode Selector SET: The light source flashes. Set to this mode to adjust the light axis. L-: Output transistor is when light is received. D-: Output transistor is when light is not received. Timer Switch : Timer function is. : Timer function is. Light Reception Monitoring Terminal Monitoring is used with the E39-VX Beam Checker 31

32 Operation Output Circuits Type Model Mode switch Output transistor NPN -T21 Light when light is received. Dark when light is not received. Light (red) Stability (green) Main circuit Tuning (red/ green) Output circuit Z D Brown Black Orange Z D Blue Pink Purple Load Load Control output Self-diagnostis output t Remote tuning input Remote bank selection input Z D : V Z = 39 V -T11 E3x-H11 -A11 -VG11 Light when light is received. Light (red) Stability (green) Main circuit Brown Black 0 ma max. Load Dark when light is not received. Z D Blue Z D : V Z = 39 V -A21 -VG21 -F21 Light when light is received. Light (red) Stability (green) Brown Load (Relay) Dark when light is not received. Main circuit Black Z D Z D K Control output Orange Pink Load (Relay) Self-diagno- sis output Externalcheck input Blue Z D : V Z = 39 V PNP -A41 Light when light is received. Light (red) Stability (green) Brown Z D Dark when light is not received. Main circuit Black 0 ma max. Load Blue Z D : V Z = 39 V -A51 -F51 Light when light is received. Brown Dark when light is not received. Light (red) Stability (green) Main circuit Z D K Z D Orange Black Pink Control output Load (Relay) External-check input Self-diagnosis output Load (Relay) Blue Z D : V Z = 39 V 32

33 Timing Charts Type Model Mode switch Output transistor NPN -T21 Light when light is received. -T11 -H11 -A11 -VG11 -A21 -VG21 -F21 Dark Light Dark Light Dark when light is not received. when light is received. when light is not received. when light is received. when light is not received. Light received Light not received Light indicator (Red) Output transistor Load (relay) Light indicator (Red) Output transistor Load (relay) Operate Release Light received Light not received Light indicator (Red) Output transistor Load (relay) Operate Release Light received Light not received Light indicator (Red) Output transistor Load (relay) Operate Release Light received Light not received Light indicator (Red) Output transistor Load (relay) Operate Release Light received Light not received Light indicator (Red) Output transistor Operate Release Light received Light not received Load (relay) Operate Release Timing chart T (Between brown and black) T (Between brown and black) (Between brown and black) (Between brown and black) T (Between brown and black) T (Between brown and black) 33

34 Type Model Mode switch Output transistor PNP -A41 Light when light is received. -A51 -F51 Dark Light Dark when light is not received. when light is received. when light is not received. Light received Light not received Light indicator (Red) Output transistor Load (relay) Light indicator (Red) Output transistor Load (relay) Operate Release Light received Light not received Light indicator (Red) Output transistor Load (relay) Operate Release Light received Light not received Light indicator (Red) Output transistor Operate Release Light received Light not received Load (relay) Operate Release Timing chart (Between blue and black) (Between blue and black) T (Between blue and black) T (Between blue and black) 34

35 Sensitivity Adjustment -T 1. Locate the sensor head in the sensing range of the. 2. Set the mode selector to TUNING. 3. Locate the object at the sensing position and press the tuning button. Through-beam Model Reflective Model Reflective Model Mark Light is not received. Base 4. Move the object and press the tuning button. The tuning indicator (red) is lit. The built-in buzzer beeps once. Through-beam Model Reflective Model Reflective Model Mark Light is received.. Base If tuning is OK: The tuning indicator turns green. The built-in buzzer beeps once. If tuning is NG: The tuning indicator (red) is still lit. The built-in buzzer beeps 3 times. Change the position of the object and the sensing distance that have been set and repeat from the beginning. 5. Set the mode setting selector to RUN to complete the sensitivity setting on the. The tuning indicator (green) is. 6. Select the logical output required with the operation mode selector. Maximum Sensitivity Setting 1. Set the mode setting selector to TUNING. 2. Press the tuning button, at which time the object may or may not be located at the sensing position. The tuning indicator (red) is lit. The built-in buzzer beeps once. 3. Set the mode setting selector to RUN to complete the maximum sensitivity setting on the. It will take approximately three seconds for the stable operation indicator or light reception indicator to be lit. After the maximum sensitivity setting is completed, the tuning indicator will turn green and then it will be automatically turned in approximately three seconds. The maximum sensitivity of the can be automatically set regardless of the set distance or light reception. The sensitivity of the -T11 and -T21 are set to maximum before shipping. 35

36 -H11/-A /-F /-VG Using a sensing object, adjust Sensitivity Adjustor so that the indicators operate as described in the following table: Through-beam Sensing method Sensing Light Indicators Interrupted With sensing object Incident Green: Light Red: Light Reflective Sensing Without sensing object With sensing object Without sensing object Incident Interrupted Green: Light Red: Light Green: Light Red: Light Green: Light Red: Light Sensing of the difference in color or shade Color that has a high reflection ratio Incident Interrupted Green: Light Red: Light Color that has a low reflection ratio Green: Light Red: Light Retroreflective Interrupted With sensing object Reflector Green: Light Red: Light Incident Without sensing object Reflector Green: Light Red: Light 1. If the indicators operate as described in the table, the can operate in stable condition within the rated temperature range. 2. Even when the green indicator is, the will operate stably if the operating temperature change since the initial settings is within + C. 36

37 Light Axis Adjustment with Flashing Function -T This function enables the user to adjust with ease the light axis of the through-beam fiber with the light source flashing. All models have this function. 1. Set the mode setting selector to FLASH. 2. If the axis of the light emission fiber head and that of the light reception fiber head do not agree with each other and the amount of light reception becomes 90% of the peak value or less, the flashing function of the will Mode Setting Selector work. The retains the peak value when the mode setting selector is set to FLASH and the axes of the fiber heads are adjusted to agree with each other. θ Fiber for light emission Fiber for light reception Optical input The peak of light reception 90% of the peak value Lit in this range. Angle of the head (θ) Flashing Lit Flashing -A /-F /-VG 1. Set the mode selector to SET. 2. Adjust the light axis by moving the fiber with the light flashing. Improper Light Axis Proper Light Axis Mode Selector Flashing Light axis adjusted Light with no flushing 3. Set the mode selector to L- or D- after the light axis is adjusted. 37 1

38 Self-diagnostic Function With this function, the checks changes in environmental conditions (especially a change in the ambient temperature) and self-diagnoses the resistance against the changes. The result is shown by the indicators or an output signal. Stable Operation Indicator (Green Indicator) Light Reception Indicator (Red Indicator) Displays Stable Operation Indicator: Changes in environmental conditions (changes in the ambient temperature, the operating voltage, or the volume of dust) are checked and the resistance against them are self-diagnosed. The result is shown via the indicator. Light Reception Indicator: The amount of light received is indicated by this indicator. Output The resistance against changes in environmental conditions is indicated by the indicator and the result is output. Amount of light Operating level x 1.2 Operating level Operating level x 0.8 Control output (L-) Self-diagnostic output* Indicator ÈÈ Green ÈÈ 0.3 s min. 0.3 s min. ÍÍÍÍÍ Red ÍÍÍÍÍ ÈÈÈÈ Green ÈÈÈÈ ÉÉÉÉÉ ÈÈÈ Green ÈÈÈ Tip of the fiber connected to the light source side in Flashing light Flashing the SET mode ÉÉÉÉÉ *If the self-diagnostic output is when the sensing object is moving at low speed, use the with an -delay timer circuit. Remote Tuning/Remote Bank Function (-T21) Remote Tuning Function Basically, the method of remote tuning is same as that of sensitivity adjustment. When the remote tuning function of the is used, the is tuned with the remote tuning input signal instead of the tuning button which has to be pressed. 1. Set the mode selector to RUN. 2. The following signal conditions must be given as remote tuning input conditions. Brown +V Black; control output Orange; self-diagnostis output Purple; remote bank selection Pink Blue 0 V If no remote tuning is done, cut off the purple wire at its source or connect the pink wire to the positive terminal of the power supply. 38 2

39 Power supply Remote tuning input Sensitivity setting H T 1 T 2 T 1 L Maximum sensitivity T 1 : 0.5 to 3 s T 2 T 2 : 0.5 to 1 s min. H L T 2 : 5 s min. Remote Bank Function The remote bank input signal allows the setting of two kinds of sensitivity adjustment values. Brown +V Black; control output Orange; self-diagnosis input Pink Purple Bank 1: SW = Bank 2: SW = Blue 0 V To set two kinds of sensitivity adjustment values, the purple and blue wires must be connected with each other and select bank 2 to tune the. Variable Hysteresis Function (-H11) Sensing of Plate Level Differences (If sensing is impossible with the hysteresis value set to maximum) Refer to the following when using the hysteresis adjuster. Reflection of light Reflection of light Reflection of light Large hysteresis differential Small hysteresis differential A B Unstable A Unstable B A B Sensing operation is not stable because zone B is within the hysteresis differential range. Reduce the sensitivity of the with the sensitivity adjuster and turn off zone B. Reduce the hysteresis value with the hysteresis adjuster so that zone A will be. 39 3

40 Set both the sensitivity adjuster and hysteresis adjuster to maximum. 1 2 SENS min max Sensitivity adjuster min max Hysteresis differential adjuster Decide the position of the fiber head and that of the sensing object in zone A. (E) Locate the head in zone A and turn the sensitivity adjuster counterclockwise slowly until the stable operation indicator and light reception indicator are (i.e., position E as shown in the illustration). 1 2 SENS min max When the head is located in zone B, light reception indicator is lit. YES S NO L Locate the head in zone B and turn the hysteresis adjuster counterclockwise slowly and make sure that the light reception indicator is lit. min NO S max L Set the hysteresis adjuster to maximum. min max S L YES S L Set the hysteresis adjuster to the point where the light reception indicator is lit (i.e., position E as shown in the illustration). (H) min max Locate the head in zone A and turn the sensitivity adjuster clockwise until the stable operation indicator and light reception indicator are (i.e., position F as shown in the illustration). (G) (F) 1 2 SENS min max The light reception indicator is lit when the head is located in zone B and the light reception indicator is when the head is located in zone A. S NO L Locate the head in zone A and turn the sensitivity adjuster counterclockwise until the light reception indicator and stable operation indicator are (i.e., position O as shown in the illustration). (G) (E) 1 2 SENS min max YES Sensing is possible. S L B A 40 4

41 External Diagnostic Input Function With this function, light projection can be stopped when desired. The operation of the sensor can be checked with this function before the is placed into actual operation. -A Light is emitted from the projection fiber head when the self-diagnostic input is. The sensor, however, will not operate. NPN Type Light projection stops Brown (+V) Pink (externalcheck Input) -F /-VG No light is emitted from the projection fiber head when self-diagnostic input is. External-diagnostic input (between blue and pink) LED for light projection Short Open Blue (0 V) Indicator Light Brown (+V) Pink (externalcheck Input) By short-circuiting the pink and blue cords, light projection can be stopped (with a short-circuit current of 0.2 ma max.). Blue (0 V) PNP Type Light projection stops Brown (+V) Pink (externalcheck Input) Blue (0 V) Brown (+V) External-diagnostic input (between brown and pink) LED for light projection Indicator Short Open Light Pink (externalcheck Input) Blue (0 V) By short-circuiting the brown and pink cords, light projection can be stopped (with a short-circuit current of 0.2 ma max.). Special Fiber Units The following special accessories are available (order separately). Contact your OMR representative for the details. Fiber Units with Special Length of Stainless Steel Tube Fiber with different lengths of stainless steel tubes are available. Applicable Models E32-TC200F (tube with 0.9 dia.) E32-TC200B/DC200F (tube with 1.2 dia.) E32-DC200B (tube with 2.5 dia.) Appearance L The length can be ordered in increments of mm between mm min. and 120 mm max. Tolerance: +1.0 mm if L is 40 mm or less. and +2.0 if L is more than 40 mm. (Note that standard Fiber Units have a 90-mm or 40-mm long stainless steel tube.) 41 5

42 Fiber Units with 90 Bend in Stainless Steel Tube Applicable Models E32-TC200B/TC200F/DC200F Appearance Stainless Steel Tube with a 90 Bend at the Base Length 2 R Stainless Steel Tube with a 90 Bend at the Tip 1 R Length Bending radius 1 (+1) R mm 15.0 mm R mm 17.5 mm R mm 20.0 mm R mm 22.5 mm The length overall is 120 mm max. If larger 1 is required, use the E39-F11 Sleeve Bender. Sensing Distance for Tubes with 90 Bends Bending radius 1 (+1) R mm.0 mm R mm 17.5 mm R.0.0 mm 20.0 mm R mm 22.5 mm Model Amplifier Bending radius The length overall is 120 mm max. If larger 2 is required, use the E39-F11 Sleeve Bender. Standard R5.0 R7.5 R.0 R12.5 E32-TC200B -T 270 mm 170 mm 220 mm 240 mm 270 mm -H mm 260 mm 330 mm 360 mm 400 mm -A 180 mm 1 mm 140 mm 160 mm 180 mm E32-TC200F -T 65 mm 30 mm 65 mm 65 mm 65 mm -H11 0 mm 55 mm 0 mm 0 mm 0 mm -A 50 mm 30 mm 50 mm 50 mm 50 mm E32-DC200F -T 20 mm 15 mm 20 mm 20 mm 20 mm -H11 36 mm 30 mm 36 mm 36 mm 36 mm -A 18 mm mm 18 mm 18 mm 18 mm Fiber Unit with Longer Fiber Applicable Models E32-TC200/-DC200 E32-TC200B/-DC200B E32-TC200E/-DC200E E32-TC200F/-DC200F E32-TC200A Appearance The length can be ordered in increments of 1 m between 6 m min. and 20 m max.. (2-m and 5-m fiber length types are standard for E32-TC200, E32-DC200.) 42 6

43 Fiber Length vs. Sensing Distance Through-beam Fiber Unit (Based on the sensing distance using a fiber length of 2 m as 0%) Reflective Fiber Unit (Based on the sensing distance using a fiber length of 2 m as 0%) (%) (%) Fiber length (m) -A, E32-TC200 (Typical) Fiber length (m) -A, E32-DC200 (Typical) (mm) (mm) Fiber length (m) Fiber length (m) 43 7

44 Dimensions Fiber Units Through-beam (Sold in Pairs) E32-T11L Two hexagon clamping nuts (T = 2.4) M2.6 x Two toothed washers (for M4) 1.4 dia Sensing head (nickelplated brass) Optical fiber, 2.2 dia. M4x0.7 E32-T12L 1.4 dia. 2.4 dia. Sensing head (nickel-plated brass) 3 dia. Optical fiber, 2.2 dia (14) 3 11 (14) E32-T21L 0.9 dia. Two hexagon clamping nuts Two toothed washers Sensing head M3 x 0.5 (nickel-plated brass) Optical fiber, 1 dia. Fiber attachment (E39-F9) 25 E32-T22L 0.9 dia. 1.8 dia. Sensing head, 2 dia. (stainless) Heat-shrinkable tubing Optical fiber, 1 dia. Fiber attachment (E39-F9) E32-TC dia. E32-T dia. (1.7) 11 M2.6 x 0.45 Sensing head SUS (2) Two hexagon clamping nuts Two toothed washers Sensing head M4 x 0.7 (nickel-plated brass) E32-TC200B E32-TC200B4 Stainless 1.0 dia. tube 1.2 (SUS304) dia max. Two hexagon clamping nuts Two toothed washers Sensing head M4 x 0.7 (nickel-plated brass) Optical fiber, 2.2 dia. 2.4 Optical fiber, 2.2 dia (40) (see note) Heat-shrinkable tubing 1.4 dia. Optical fiber, 1 dia. Fiber attachment (E39-F9) 25 E32-TC200E 0.5 dia. The value in the parentheses is for the E32-TC200B4. Two hexagon clamping nuts Two toothed washers Sensing head M3 x 0.5 (nickel-plated brass) Optical fiber, 1 dia. Fiber attachment (E39-F9) 25 2 dia E32-TC200F E32-TC200F4 Stainless tube (SUS304) 0.5 dia. 0.9 dia. min. Two hexagon clamping nuts Two toothed washers Sensing head M3 x 0.5 (nickel-plated brass) Optical fiber, 1 dia. Fiber attachment (E39-F9) (40) (see note) The value in the parentheses is for the E32-TC200F4. E32-TC200A 1.0 dia. 2.6 dia. Two hexagon clamping nuts Two toothed washers Sensing head M3 x 0.5 (nickel-plated brass) E32-T11 Sensing head (nickelplated brass) M4 x 0.7 Sixteen, dia. M2.6 x 0.45 Two hexagon clamping nuts Two toothed washers Protective tube Optical fiber, 2.2 dia. 5.5 (1.5) dia. Optical fiber, 2.2 dia (14)

45 E32-T21 Sensing head (nickel-plated brass) M3 x 0.5 Two hexagon clamping nuts Four, 0.25 dia. Two toothed washers Protective tube Optical fiber, 1 dia. Fiber attachment (E39-F9) 25 E32-TC200C dia. Two hexagon clamping nuts Sensing head Two toothed washers M2.6 x 0.45 M4x0.7 (nickelplated brass) (75) 22 dia Optical fiber, 2.2 dia. E32-TC200D E32-TC200D4 E32-T14L Two hexagon clamping nuts Stainless Two toothed washers 1.0 dia. tube Sensing head M4 x (SUS304) 0.7 (nickel-plated 1.2 brass) dia. max Optical fiber, 2.2 dia (40) (see note) Sensing head, 3 dia. (stainless) (when straight) (75) (when straight) Heat-shrinking tubing Optical fiber, 2.2 dia. 22 dia. The value in the parentheses is for the E32-TC200D dia Sensing surface E32-T24 Sensing head 1 dia. SUS304 2 dia. 1.4 dia. 45% Protective tube Optical fiber, 1 dia. Fiber attachment (E39-F9) E32-T14 Lens unit (PMMA) 4.4 dia Heat resistive ABS E32-T17L Sensing head (ABS) M14 x 1 -mm dia. lens (PMMA) Two hexagon clamping nuts Optical fiber, 2.2 dia. R3.5 Optical axis Two, 3.2 dia. Optical fiber, 2.2 dia ,000 E32-T12F 4-mm dia. lens Sensing head, 5 dia. Fluoride resin 4 dia. Optical fiber, 2.2 dia

46 E32-M21 Sensing head M3 x 0.35 (SUS303) Two hexagon clamping nuts Two toothed washers Silicone tube Plastic fibers, four, 1 dia. One set of silicone tubes is black while the other set is gray for easy identification when they are connected to the light source and receiver. Sleeve E32-T dia. Two hexagon clamping nuts Two toothed washers Sensing head M4 x 0.7 (nickel-plated brass) Resistant temperature is 150 C. Resistant temperature is 130 C when used continuously dia Optical fiber, 2.2 dia. E32-T dia. M2.6 x 0.45 Two hexagon clamping nuts Two toothed washers SUS flexible tube Hexagon clamping screw Sensing head M4 x dia. 4 dia. 5 dia. Sleeve (SUS303) 4 dia A 5 28 B (See note) 13 Section A resists 300 C and section B (which is inserted to the Amplifier) resists 1 C. The operating temperature of section B must also be within the withstand temperature range of the Amplifier. 46 3

47 Reflective E32-D11L Two, 1.4 dia. 4 dia. Two hexagon clamping nuts Two toothed washers Sensing head (nickel-plated brass) M6 x 0.75 Two optical fiber, 2.2 dia E32-D12 3 dia (standard length) Two, 1 dia. Sensing head (stainless) Heat-shrinkable tubing Optical fibers, two, 2.2 dia. E32-D21L Two, 0.9 dia. Two hexagon clamping nuts Two toothed washers Sensing head M4 x 0.7 (nickel-plated brass) Optical fiber, two, 1 dia. Two fiber attachments (E39-F9) E32-D22L Two, 0.9 dia. 2.7 dia. Sensing head 3 dia. (nickel-plated brass) Optical fiber, two, 1 dia. Two fiber attachments (E39-F9) E32-DC200 Two hexagon clamping nuts Two, 1.0 dia. 4 dia. Two toothed washers Sensing head M6 x 0.75 (ADC) Optical fiber, 2.2 dia. E32-DC200B E32-DC200B4 E32-DC200E 4.8 Two, 1.0 dia dia. max. Two, 0.5 dia. 3 Stainless tube (SUS304) (40) (see note) Two hexagon clamping nuts Two toothed washers Sensing head M6 x 0.75 (fine screw) Two hexagon clamping nuts Two toothed washers Sensing head M3 x 0.5 (SUS304) Optical fiber, two, 1 dia. Optical fiber, 2.2 dia. Two fiber attachments (E39-F9) 25 The value in the parentheses is for the E32-DC200B

48 E32-DC200F E32-DC200F4 Stainless tube Two, 0.5 dia. (SUS304) 1.2 dia. min. Two hexagon clamping nuts Two toothed washers Sensing head M3 x 0.5 (SUS304) Optical fiber, two, 1 dia. Fiber attachment (E39-F9) (40) (see note) The value in the parentheses is for the E32-TC200F4. E32-D11 Sixteen, dia. Sensing head (SUS303) Two hexagon clamping nuts M6 X 0.75 Two toothed washers ( teeth) Protective tube Optical fiber, two, 2.2 dia E32-D21 Sensing head (nickel-plated brass) M3 x 0.5 Two hexagon clamping nuts Two toothed washers Four, 0.25 dia. Protective tube Optical fiber, two, 1 dia. Fiber attachment (E39-F9) E32-DC200C Two, 1.0 dia. Two hexagon clamping nuts Two toothed washers Sensing head M6 x 0.75 (nickelplated brass) (150) 22 dia. 5.2 Optical fiber, x 2 dia (when straight) E32-DC200D E32-DC200D4 Stainless Two, 1.0 dia. tube 2.5 dia. (SUS304) max. Two hexagon clamping nuts Two toothed washers Sensing head M6 x 0.75 (SUS304) (150) 22 dia. The value in the parentheses is for the E32-DC200D (40) (see note) Optical fiber, two, 2.2 dia. 90 (when straight) 400 E32-DC9G E32-DC9G4 1.2 dia. max. Stainless tube 4 Sleeve 8 15 Do not bent the stainless tube in this range (40) (see note) The value in the parentheses is for the E32-TC200F4. E32-D33 Two, 0.25 dia. Sensing head (SUS303) 0.8 dia. 3 dia. Heat-shrinkable tubing Optical fiber, two, 1 dia. Fiber attachment (E39-F9)

49 E32-CC200 Sixteen, 0.25 dia. for light reception 1.0 dia. for light emission 2.5 dia. Two hexagon clamping nuts Two toothed washers Sensing head M6 x 0.75 Optical fiber, two, 2.2 dia. (nickel-plated brass) The fiber for the light source is identified by a white line. E32-D32 Light source fiber (0.5 dia.) Sensing head SUS303 Optical fibers, two, 1 dia. 2 dia. 3 dia. Heat-shrinkable tubing Two fiber attachments (E39-F9) 25 Receive fiber (0.25 dia.) x E32-D32L Light source (1 dia.) The fiber for the light source is identified by a white line. (standard length) ,570 Receive (0.265 dia.) x 16 Sensing head, 3 dia. (stainless) Branching box, 6 dia. (heat-resistive ABS black resin) Optical fibers, two, 2.2 dia. The fiber for the light source is identified by a yellow dotted line. E32-D14L 45 Sensing head (stainless) Heat-shrinkable tubing Optical fiber, two, 2.2 dia dia Light baffle E32-D24 Sensing surface Sensing head (SUS304) 45% 2 dia. 3 dia. Heat-shrinkable tubing Optical fibers, two, 1 dia. Two fiber attachments (E39-F9) Light baffle Sensing surface E32-D12F Sensing head, 6 dia. Fluoride resin 5 dia. Optical fiber, two, 2.2 dia

50 E32-D Two, 1.5 dia. 4.9 Two hexagon clamping nuts Two toothed washers Sensing head,m6 x 0.75* Optical fiber, 2.2 dia. *nickel-plated brass Resistant temperature is 150 C. Resistant temperature is 130 C when used continuously. E32-D dia. M4 x 0.7 Two hexagon clamping nuts Two toothed washers Sensing head (SUS303) M3 x dia. 3.5 dia. SUS flexible tube Hexagon clamping screw SUS304 Sleeve A B (See note) Section A resists 300 C and section B (which is inserted to the Amplifier) resists 1 C. The operating temperature of section B must also be within the withstand temperature range of the Amplifier. E32-D dia. Sensing head 1.25 dia. 2.5 dia dia. Two hexagon clamping nuts Two toothed washers M4 x 0.7 (SUS303) SUS flexible tube 4 dia. 2.8 dia. SUS303 Hexagon clamping screw 5 dia. Sleeve A B (See note) 13 C 6.4 E32-R21 Lens (PMMA) Section A resists 400 C, section B resists 300 C, and section C (which is inserted to the Amplifier) resists 1 C. The operating temperature of section C must also be within the withstand temperature range of the Amplifier. Sensing head Two hexagon clamping nuts Two washers Silicone tube M6 x 0.75 Optical fibers, two, 1 dia. Two fiber attachments (E39-F9) 25 5 dia E32-R16 Nameplate (6) Lens (PMMA) Optical fiber, two, 2.2 dia. Standard length: 2 m Two, M3 screws (attachment) Mounting bracket (attachment) 50 7

51 E32-L25 E32-L25A White line Optical fiber, two, 2.2 dia. Two, 3.2 dia., 6 dia. spot facing Two, 3.2 dia., 6 dia. spot facing White line Sensing head (ABS) The fiber for the light source is identified by a white line. Optical fiber, two, 2.2 dia. E32-L25L 4 18 Two fiber attachment (E39-F9) Two, 1 dia. optical fibers Sensing head (PC) Two, 3.2 dia, 6 dia. counter sinking E32-L24L Side view prism (PC) Two fiber attachment (E39-F9) 20 Optical axis Two, 1 dia. optical fibers 25 Sensing head (PC) Two, 3.2 dia, 6 dia. counter sinking 51 8

52 Fine Through-beam E32-T22S E32-T24S Sensing head (nickel-plate brass) Optical fiber 2.2 dia. 3.5 dia Mounting bracket (attachment) 2 dia. 2 Sensing surface E32-T84S (standard length) (see note) 4 dia. 2.9 dia. flexible tube (stainless) 4 dia. 5 dia. Sleeve 3.5 dia. Sensing head (stainless) 3 dia. Lens (2 dia.) Section A resists 200 C and section B (which is inserted to the Amplifier) resists 1 C. The operating temperature of section B must also be within the withstand temperature range of the Amplifier. Slot Fiber Units E32-G14 Sensing head (ABS) R1.6 R1.6 Mounting Holes Two, M3 R Optical axis Lens (PMMA) Optical fiber, 2.2 dia

53 Liquid Level Fiber Units E32-D82F1/E32-D82F2 (Liquid Contact Model) 6 dia. sensing head (Teflon) 9 dia. fiber connector (nickel-plate brass) Two, 2.2 dia. optical fiber (see note 2) Bending-prohibited length: 150 (350) (see note 1) To Amplifier 1. The value in the parentheses is for the E32-D82F2. 2. Since the 2-m optical fiber on the Amplifier side is made of plastic, the fiber is trimmable. E32-L25T (Pipe Mounting Model) Optical axis Two, 3.2 dia. lens (PC) Two, fiber attachment Two, 1 dia. optical fiber Mounting hole Sensing head (PC) (standard length) 53

54 E32-T (R) 4 20 Mounting Holes mm Wide Silt Seal (Sold in Pairs) Sensing head (ABS) (R) Two, M (R) Black dia. 20 Lens (2 x ) (PMMA) Two, 3.2 dia. 1-mm Wide Silt Seal (Sold in Pairs) Mounting bracket E39-L Black Fiber 2.2 dia. 33 E32-T16P Two, 3.2 dia., 6 dia counter sinking mm-wide Slit Seal (Sold in Pairs) E32-T16P with E39-L94 Mounting Sensing head (2 x 11) (PMMA) Two, M Sensing head (heat-resistive ABS) Black mm-wide Slit Seal (Sold in Pairs) Sensing head dia. optical fiber Black 2.2-dia. fiber E39-L94 Mounting Bracket

55 Amplifier -T11 -T Light reception indicator Stable operation indicator 1.2 Tuning indicator 59 4 Two, Cord: 2-m polyvinyl chloride-covered cord (4-mm dia., 3 cores*) Weight: Approx. 0 g *The cords for the -T21 model has 6 cores dia. Mounting bracket (removable) H11 -A -F -VG 15.8 Light reception indicator 9 Stable operation indicator 59 4 Two, 2.4 dia Cord: 2-m polyvinyl chloride-covered cord (4-mm dia., 5 cores*) Weight: Approx. 0 g *The cords for the -A11, -A41, and -VG11 models have 3 cores Mounting bracket (removable) 3.2 dia

56 Reflector Reflector (Small) E39-R3 Reflector E39-R1 11 Adhesive tape Two, 3.5 dia Mounting bracket is attached Two, M Attachments E39-F1 Lens Kit 4 dia. 8.9 M2.6 x 0.45 Effective depth: 3.8 Spot facing depth: 0.9 E39-F2 Side-view Attachment 4 dia. 2.8 dia M2.6 Effective depth: 3.2 Spot facing depth: 0.9 E39-F3 Convergent Beam Conversion Kit Two, 4 dia. M3 toothed washers +0.2 Two, dia. Two, M3 x 3 Slotted head machine screw One set includes two units. E39-F5 Side-view Diffuse Reflective Conversion Kit (for the E32-TC200A) E39-F3A Reflective Lens Unit (for the E32-D32) M3 x 6 Angle fixing screw Sensing hole Two, 3.2 dia Two, 3.2 dia. Mounting hole Two, M3 Fiber unit mounting holes (E32-TC200A) dia. 4 dia. Lens (3.7 dia.) M2 x dia

57 Protective Spiral Tubes E39-F32A, E39-F32A5 E39-F32B, E39-F32B5 M3 x 0.5 depth: 4 Head connector 4.6 dia. End cap 3 dia. 6 dia. E39-F32C, E39-F32C5 M4 x 0.7 depth: L 1. L is as follows: E39-F32A and E39-F32B: 1,000 E39-F32A5, E39-F32B5: A pair of E39-F32A(5) s is sold as E39-F32B(5). 7 dia. Head connector 5.6 dia. End cap 4 dia L L is as follows: E39-F32C: 1,000 E39-F32C5: 500 E39-F32D, E39-F32D5 M6 x 0.75 depth: 4 Head connector 7 dia. End cap 5 dia. 8.5 dia. 12 L 12 L is as follows: E39-F32D: 1,000 E39-F32D5: 500 Accessories E39-F4 Fiber Cutter Holes for standard fiber Holes for thin fiber E39-F9 Attachment for Thin Fiber E39-F Fiber Connector 1.1 dia. Insertion mark Retention clip Splice Retention clip Fiber 3.6 dia (2.4 dia.) 3.8 dia dia dia. One set includes two Units

58 E39-G3 Manual Sensitivity Adjustment Knob Cannot be used with the -T. dia. E39-G4 Protective Cover Cannot be used with the -T

59 Installation Connections Connection with S3D2 Sensor Controller Connection with S3D8 Sensor Controller Blue Black Brown Black Blue 0 V Brown +12 V 0 V V IN1 IN1 IN2 NORM INV A maximum of two Optical Fiber Photoelectric Sensors can be connected. A maximum of eight Optical Fiber Photoelectric Sensors can be connected. Power supply voltage Output Functions NPN input PNP input 0 to 240 VAC Relay AND, OR S3D2-AK-US S3D2-AKB-US AND, OR, and timer S3D2-CK-US S3D2-CKB-US Flip-flop S3D2-BK-US --- Transistor AND, OR, and timer S3D2-CC-US S3D2-CCB-US 59 16

60 Precautions Fiber Units Tightening Force The tightening force applied to the Fiber Unit should be as follows: Screw-mounting Model Spring mounting clip Toothed washers Fiber Connection and Disconnection The Amplifier has a push lock. Connect or disconnect the fibers to or from the Amplifier using the following procedures: 1. Connection Nuts (attachment) Column Model Retaining screw (M 3 max.) Clamping torque 3 kgf cm max. Fiber units Clamping torque M3/M4 screw 8 kgf cm max. (0.78 N m) M6 screw kgf cm max. (0.98 N m) 2-mm dia. column 3 kgf cm max. (0.29 N m) 3-mm dia. column 3 kgf cm max. (0.29 N m) E32-D14L kgf cm max. (0.98 N m) E32-T12F 8 kgf cm max. (0.78 N m) E32-D12F 8 kgf cm max. (0.78 N m) E32-T16 5 kgf cm max. (0.49 N m) E32-R21 6 kgf cm max. (0.59 N m) E32-M21 Up to 5 mm to the tip: 5 kgf cm max. (0.49 N m) Up to 5 mm from the tip: 8 kgf cm max. (0.78 N m) E32-L25A 8 kgf cm max. (0.78 N m) Insert the fibers into the Amplifier and press the push lock until the Amplifier clicks to lock the fibers. The fibers will have insertion marks when they are cut with the E39-F4 (Fiber Cutter). The portion from the tips to the insertion mark should be inserted to the. 2. Disconnection Be sure to press the push lock again to unlock before pulling out the fiber, otherwise the fiber may be deteriorated. Fiber Insertion If the portion from the tip to the insertion mark of the fibers are not inserted into the Amplifier Unit, the sensing distance will be reduced. 2.2-mm dia. Fiber Insertion mark Fiber unit Amplifier Thin Fiber with the E39-F4 Attachment The portion from the tips to the insertion mark should be inserted into the. Fiber unit 12.6 mm 12.6 mm Amplifier Use a proper-sized wrench. Fiber with Fixed Length The portion from the tips to the insertion mark should be inserted into the. Amplifier 12.6 mm 17 60

61 Cutting Fiber Insert a fiber into the Fiber Cutter and determine the length of the fiber to be cut. Press down the Fiber Cutter in a single stroke to cut the fiber. When the fiber is cut, an insertion mark is inscribed on the fiber. For a 2.2-mm dia. standard fiber only dia. Insertion mark Connection Do not pull or press the Fiber Units. The Fiber Units have a withstand force of 1 kg or 3 kg (pay utmost attention because the fibers are thin). Do not bend the Fiber Units beyond the permissible bending radius. Do not bend the edge of the Fiber Units. Correct Amplifier 40 mm max. Fiber unit Insert a fiber into the Fiber Cutter in the direction indicated by the arrow (refer to the following figure). 2 Incorrect 20 mm max. The cutting holes cannot be used twice. If the same hole is used twice, the cutting face of the fiber will be rough and the sensing distance will be reduced. Always use an unused hole. Use either one of the two holes on the right (refer to the following figure) to cut a thin fiber as follows: 1. An attachment is temporarily fitted to a thin fiber before shipment. 2. Secure the attachment after adjusting the position of it in the direction indicated by the arrow. 3. Insert the fiber into the E39-F4 to cut. 1 Temporarily fitted Do not apply excess force on the Fiber Units. Correct Incorrect Fiber unit Nylon wireholder Metal holder The Fiber Head could be broken by excessive vibration. To prevent this, the following is effective: A A one-turn loop loop can can absorb absorb vibrations. Cutter E39-F4 Two holes for thin fiber Tape Three holes for standard fiber (2.2 mm dia.) Insert the fiber in the direction indicated by the arrow

62 Bending Radius E39-F11 Sleeve Bender The bending radius of the stainless tube should be as large as possible. The smaller the bending radius becomes, the shorter the sensing distance will be. Insert the tip of the stainless sleeve to the Sleeve Bender and bend the stainless sleeve slowly along the curve of the Sleeve Bender (refer to the figure). R 12.5 R dia. 1.2 dia. max. 1.3 dia. max. min. R R 5 Fiber tip position mark Handling E32-D51/-T51 Heat-resisting Fiber The bending radius of the fibers should be 35 mm min. Connecting fibers via the E39-F Fiber Connector is not possible. The withstand temperature of the Heat-Resisting Fibers is 150 C max. In continuous operation, the ambient temperature should be 130 C max. E32-T14/-T51 If the sensor is because some object in front of the lenses reflects light, attach the black seals (sold together) to the lenses. E32-T14/-G14 Seal 90 o max. Stainless tube E32-L25 (A) Wafer Sensor Insert the fiber with a white line into the light projection side of the Amplifier. The tightening force of the sensor head is 8 kgf cm (0.75 N m). Avoid places where water could be sprayed onto the E32-L25(A). E32-T16 Slit Seal (Attachment) Peel the E32-T16 Slit Seal off the ground paper and affix the Slit Seal to the sensing face of the sensor so that the corners of the Slit Seal fit in with the corners of the sensing face. To sense an object at a distance of 30 cm max., a 0.5-mm wide Slit Seal must be used. Do not bend here. E32-T16 Sensing Head Attachment slit Amplifier Units Mounting Mounting 1. Mount the front part on the mounting bracket (sold together) or a DIN rail. 2. Press the back part onto the mounting bracket or the DIN rail. 1 DIN rail Dismounting By pulling back the lock (yellow) on the bottom with a flat blade screwdriver, the Amplifier can be dismounted with ease. In the case of side mounting, attach the mounting bracket on the Amplifier first, and secure the Amplifier with M3 screws and washers. The diameter of the washers should be 6 mm max. Washers (6 dia. max.) 2 3 Others When power is off: The moment power is turned off, the could output a pulse signal which could affect the operation of the devices connected to it. This will happen more often if power is supplied to the from an external power supply, thus affecting the connected timer and counter. Use a built-in power supply as much as possible to avoid this. If power is supplied to a photoelectric sensor through a cord that is wired together with other power lines in the same duct, the cord will be influenced by the power lines and malfunctioning of the photoelectric sensor or damage could result. Wire the cord separately or use a sealed cord to supply power to the photoelectric sensor. In the case of the cord is extended, use a wire with 0.3 mm 2 max.. The total length of the cord should be 0 m max. Power Power line line Power supply: If a standard switching regulator is used as a power supply, the frame ground (FG) terminal and the ground (G) terminal must be grounded, or otherwise the can malfunction, influenced by the switching noise of the power supply. The supplied voltage must be within the rated voltage range. Unregulated full- or half-wave rectifiers must not be used as power supplies. Do not use a hammer to hit the Amplifier when mounting or the Amplifier will loose watertightness

63 Attachment Units Applications E39-F Fiber Connector Use the following procedure (refer to the figure) to connect fibers via the Fiber Connector. Retention Unit Splice Retention Unit E39-F3A Reflective Unit Lens When the E39-F3A is attached to the fiber, the can sense the light reflected from the interior of the E39-F3A. If this happens, adjust the sensitivity of the Amplifier with Sensitivity Adjustor. Place a sensing object or white paper at the sensing distance set and adjust the insertion length of the Fiber Unit to the E39-F3A so that the light spot is as small as possible. Then fix the position of the Fiber Unit with the hexagonal wrench (attachment) Tighten Each fiber should be as close as possible before they are connected. will be reduced by approximately 25% when fibers are connected. Only fibers with 2.2 mm dia. can be connected. Protective Spiral Tube Insert a fiber to the Protective Spiral Tube from the head connector side (screwed) of the tube. Loosen B A Insertion Fiber Unit (E32-D32) Lens A: The focus is farther than the E39-F3A. B: The focus is closer than the E39-F3A E39-G3 Sensitivity Adjustor 1. Remove the cover of the. 2. Attach the E39-G3 (refer to the figure). Protective spiral tube Fiber Unit Knob Cover Push the fiber into the Protective Spiral Tube. The tube should be straight so that the fiber is not twisted when inserted. Then turn the end cap of the spiral tube. Protective spiral tube Fiber Unit Secure the Protective Spiral Tube on a suitable place with the attached nut. Mounting panel Hexagon clamping nut 3. After the cover is attached to the case, turn the knob of the E39-F3A clockwise or counterclockwise once. To confirm that the knob has been set properly, turn the knob clockwise or counterclockwise until you hear a click (8 turns max. are necessary). looses watertightness if E39-G3 is attached (the enclosure rating will be IP50). Protective spiral tube Fiber Unit Toothed washer Use the attached saddle to secure the end cap of the Protective Spiral Tube. To secure the Protective Spiral Tube at a position other than the end cap, apply tape to the tube so that the portion becomes thicker in diameter. Saddle Tube End cap 63 20

64 ALL DIMENSIS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by To convert grams into ounces, multiply by Cat. No. E215-E1-3 OMR Corporation Systems Components Division H.Q. 28F Crystal Tower Bldg , Shiromi, Chuo-ku, Osaka 540 Japan Phone: Fax: In the interest of product improvement, specifications are subject to change without notice. Printed in Japan M (0691) a 64 21