Installation Instructions

Transcription

1 nstallation nstructions RYL SOWR SS NOT: O NOT STOR UNTS OUTOORS. KP OUT OF SUNLT N XPOSUR TO WTR. Keep the unit cartoned all the way to the bathroom site for added protection. Unit should be handled with care. Preparation for nstallation: f possible, provide access to the shower drain. n most cases, the drain fitting should be installed through the pre-drilled hole before the unit is placed in the framed pocket. When installing the base on a slab, the drain must be installed before moving it into place. The base will have to be tilted or lifted so that the drain collar slips over the pipe. five inch diameter hole through the slab around the pipe will permit the collar of the drain fitting to extend below the top surface of the slab. Otherwise, a lower profile drain fitting will have to be obtained. f the shower base is installed over a basement or in a place where the drain connections are accessible from below, the drain fitting and waste pipe can be installed after the shower base has been placed in the framed pocket. The width of the shower door enclosure will be determined by the finished wall materials. See: etermining lass nclosure imensions section of this manual for more information. See applicable PROUT RM or dimensional information when planning the framed pocket. NSTLLTON: mportant: Read complete instructions before beginning installation Upon receipt of the shower base, immediately inspect it for damage or defects. f any are noted, o Not install the shower base and contact ustomer Service at Plan the installation in relation to the finished wall surfaces. Take into account the dimensions of both the shower base and the shower door to be used with it. x 4 LOKN FNS WLL FUR TYPL ROSS STON NTRY 7-/" (9mm) 6" (5mm) SU FLOOR " WST PP MORTR OR PLST TO LVL & SUPPORT SOWR S TTNTON NSTLLR: PLS LV TS NSTRUTONS WT T ONSUMR Product Specifications May hange Without Notice

2 Make sure your framed pocket is square and plumb in accordance with rough-in dimensions shown in the appropriate PROUT RM. 7-/" (9mm) 5" x 5" OPNN FUR " (03mm) Rectangular with Right or Left and rain Models: WL30R, WL30L, WL3R, WL3L 7-/" (9mm) 5" x 5" OPNN FUR 3 Square and Rectangular with enter rain Models: WL33N, WLN, WLN, WL4N, WL43N, WL4N, WL3N, WLN00 7-/" (9mm) 5" x 5" OPNN FUR 4 Neo-ngle Showers Models: WLN, WL33N Provide an opening in the sub floor no less than 5" x 5" square. This opening should be centered on the shower base drain hole. (See PROUT RM). The opening should accommodate a " waste pipe. The waste pipe should be /" above the surface of the sub floor

3 RYL SOWR S PROUT RM /" 3" /" imensions in nches MOL WL33N WLN WLN WL4N WL43N WL4N WL30L WL30R WL3N WL3L WL3R WLN F " WL Left/Right rain /" 3" /" WL Square/Rectangular rain " Stud Line Nail or Screw Wall oard aulk NO-NL SOWR S PROUT RM /" 3" imensions in nches MOL WLN WL33N N/ N/ F N/ N/.5 6" WL Left/Right rain " Stud Line Nail or Screw Wall oard aulk

4 rain ody Silicone Sealant Rubber asket FUR 5 Strainer Shower ase Fiber asket Locking Nut When the base is level and the bottom edge of the dam is fully in contact with the sub floor, attach it to the framing through the mounting flanges. Pre-drill pilot holes, and countersink. ttach with drywall screws or galvanized roofing nails into the blocking and wall studs every " inches. nstall wallboard above the mounting flanges and secure to studs. pply tile (or other finishing material) over the wallboard leaving an /" gap between the bottom of the finish material and the splash rim of the base. aulk this gap. Remove the strainer from the drain assembly. isassemble the locknut and two gaskets. pply a /4" bead of caulking (silicone) to the drain hole in the shower and insert the drain body. nstall the rubber washer, fiber washer, and lock nut (in that order). and tighten the locknut. Remove excess caulking from the finished side. (See Figure 5). pply a lubricant (liquid soap for example) to the inside of the rubber seal of the drain. This will permit the " diameter waste pipe to slip into the drain assembly as the shower base is lowered into place. f installing the shower base over a basement or crawlspace, the waste pipe can be installed after the shower is placed in the framed pocket. pply a grid pattern of mortar or plaster to the sub floor in the alcove. With the drain assembly passing over the waste pipe slowly lower the shower base into place. Push down firmly until the base is level in all directions. /4" high shim is needed to insure a level base since the top of the threshold is /4" higher than the back or sides of the shower. (See Figure 6). TL TL SV ULK /" P WLL OR STU LN SRW OR NL SRW OR NL TL STU LN SOWR S FUR 7 Using a large screwdriver and the tool provided with the drain, tighten the inside compression nut to seal the waste pipe connection. Finish the installation by snapping the strainer into place. NOT: Watertight installation of the drain is installers responsibility. rain leakage is excluded from the limited warranty. LVL /4" SM MORTR OR PLST FUR 6 TOP OF M FUR

5 etermining lass nclosure imensions f installing a square or rectangular shower base, subtract from the stud wall at each side to arrive at the correct door opening size. gain, if alternate materials are used, adjust the dimensions accordingly. TUL OOR WT ROMMN SOWR OORS SQUR / RTNULR SOWRS WL33N: 4 WLN: 44 WLN: 46 WL4N: 930 WL43N: 975 WL4N: 975 WL30R: 995 WL30L: 995 WL3: 995 WL3L: 995 WL3N: 995 WLN: 995 FUR 9 L OF TRSOL Neo-ngle Showers MOL WLN WL33N 7" 6-5/" 3-3/" 7" represents the dimension from the stud wall to the face of the finish materials. t assumes installation of /" thick wall board attached to the studs above the shower mounting flanges, and /4" nominal thickness ceramic wall tile. f other materials are used, adjust the dimensions accordingly. FT Products Shower Fixtures may vary + or - /" to the example indicated. FUR

6 Shower ase are and leaning This base is made of co-extruded acrylic. t has been specifically designed and engineered to exceed demanding strength and stress factors required for use. t is stain resistant, high gloss finish. Like any fine finish, it requires reasonable care to maintain its beauty and luster. ay-to-ay leaning: Wash with warm water, a soft cloth and mild liquid detergent. For Stubborn Stains: Use a Nonabrasive, liquid detergent cleaner, or a product made to clean acrylic, applied using a soft cloth. To nhance The Luster: ulled areas may be restored or light scratches removed by rubbing with a plastic polish such as el-loss or Novis Plastic Polish No., or in extreme cases with a light-duty automotive compound. f automotive compound is used, it should be followed by a light application of automotive paste wax or Novis Plastic Polish No.. aution: ry cleaning agents and solvents will damage the surface. urning cigarettes should not be allowed to come into contact with the surface or discoloration may ensue. NVR US RSV SOURN POWRS, SOLVNT S LNSRS, OR SOURN PS S TY TN TO ULL T FNS. Limited Five Year Warranty Subject to the xclusions set forth below, FT Products promises to the consumer to repair, or at the option of FT Products, to replace any part of this plumbing product,and any other supplied part of this product under normal use for one year from the date of purchase. ll costs of removal, transportation and reinstallation to obtain warranty service shall be paid by the consumer. uring the warranty period, FT Products will provide, subject to the xclusions" section setforth below, all parts free of charge, necessary to correct defects, if this plumbing product has been installed and maintained in accordance with written instructions furnished by FT Products with this plumbing product. xclusions: FT PROUTS SLL NOT LL FOR NNTL OR ONSQUNTL MS, NLUN OSTS OF NSTLLTON, WTR M, OR FOR MS RSULTN FROM US OR MSUS OR FROM FLUR TO NSTLL OR MNTN TS PLUMN PROUT N ORN WT T WRTTN NSTRUTONS FURNS Y FT PROUTS. T US OF LNN PROUTS ONTNN LUM YPORT (LORN) SLL ONSTTUT MPROPR MNTNN. SOM STTS O NOT LLOW T XLUSON OR LMTTON OF NNTL OR ONSQUNTL MS, SO T OV LMTTON MY NOT PPLY TO T ONSUMR. T ONLY WRRNTY M Y FT PROUTS S ST FORT OV N LL MPL WRRNTS W MT RS, NLUN T MPL WRRNTS OF MRNTLTY OR FTNSS FOR PRTULR PURPOS R R Y XLU.Warrant Service: n order to obtain warranty service or adjustments, contact the builder, dealer, or plumber from whom the product was purchased, or the ustomer Service epartment. n obtaining warranty service, all transportation, shipping, and freight charges connected with transporting any part of this plumbing product must be prepaid by the consumer. t is the responsibility of the consumer to establish the warranty period by verifying the original purchase date. bill of sale, cancelled check or some other appropriate payment record may be kept for this purpose. This warranty give you specific legal rights. You may also have other rights which vary from state to state. Replacement Parts Please keep this manual for future reference. Retain product invoice in case warranty service becomes necessary. Record the Model Number in this booklet. This will assist when ordering replacement parts, or in seeking technical assistance. Technical ssistance or Replacement Parts may be obtained by contacting: FT USTOMR SRV UNT STTS N Packing List Qty escription Shower Floor rain ssembly Mechanical No-aulk onnection WL nstallation nstruction